Honeywell 7580 Genesis User's Guide User Manual To The 91874fdb 57ba 474f 9c4b 505739350b9f

User Manual: Honeywell 7580 to the manual

Open the PDF directly: View PDF .
Page Count: 68

Genesis 7580

Presentation Area Imager

User’s Guide

Disclaimer

Honeywell International Inc. (“HII”) reserves the right to make changes in

specifications and other information contained in this document without prior

notice, and the reader should in all cases consult HII to determine whether any

such changes have been made. The information in this publication does not

represent a commitment on the part of HII.

HII shall not be liable for technical or editorial errors or omissions contained

herein: nor for incidental or consequential damages resulting from the furnishing,

performance, or use of this manual.

This document contains propriety information that is protected by copyright.

All rights reserved. No part of this document may be photocopied, reproduced,

or translated into another language without the prior written consent of HII.

© 2010 - 2012 Honeywell International Inc. All rights reserved.

Web Address: www.honeywellaidc.com

Trademarks

SwiftDecoder, MetroSelect, and MetroSet are trademarks or registered

trademarks of Metrologic Instruments, Inc. in the United States and/or other

countries.

Microsoft, Windows 95, and Windows are registered trademarks of Microsoft

Corporation.

IBM is a trademark of International Business Machines Corporation.

Checkpoint is a registered trademark of Checkpoint Systems, Inc.

Other product names mentioned in this manual may be trademarks or

registered trademarks of their respective companies and are the property of their

respective owners.

Patents

For patent information, please refer to www.honeywellaidc.com/patents.

iii

Table of Contents

Introduction

Product Overview ............................................................................................. 1

Base Kit Components ....................................................................................... 2

Optional Accessories ........................................................................................ 2

MS7580 Components ....................................................................................... 4

Labels ............................................................................................................... 5

Maintenance ..................................................................................................... 5

Cable Installation and Removal ........................................................................ 6

Interface Installation

RS232 .............................................................................................................. 7

Keyboard Wedge .............................................................................................. 8

RS485 .............................................................................................................. 9

USB ................................................................................................................ 10

Mounting the MS7580

Components of Adapter Kit 46-00911 ............................................................ 13

Components of Wall Mount Kit 46-00913 ....................................................... 13

Installation of Adapter Kit 46-00911 ............................................................... 14

Installation of Wall Mount Kit 46-00913 .......................................................... 16

Operation

Modes of Operation ........................................................................................ 17

Audible Indicators ........................................................................................... 19

Visual Indicators ............................................................................................. 20

Failure Modes ................................................................................................. 21

Field of View ................................................................................................... 22

Depth of Field by Minimum Bar Code Element Width .................................... 23

IR Activation Range ........................................................................................ 24

Illumination Source ......................................................................................... 25

IR Source ....................................................................................................... 26

Targeting Source ............................................................................................ 27

iv

Troubleshooting Guide ......................................................................... 29

Design Specifications ........................................................................... 33

Applications and Protocols .................................................................. 35

Configuration and Upgrades ................................................................ 37

Configuration Modes ...................................................................................... 37

Upgrading the Firmware ................................................................................. 37

MS7580-124-EAS Model

Integrated RF EAS Antenna Connection ........................................................ 39

EAS System Connection ................................................................................ 40

Configuration for EAS Applications ................................................................ 42

EAS Tag Deactivation Range ......................................................................... 44

Imager Pinouts–MS7580-124-EAS ................................................................ 46

Cable Pinouts ................................................................................................. 47

Antenna Disconnect ....................................................................................... 47

Imager and Cable Terminations

Standard Imager Pinouts ................................................................................ 49

Standard Cable Pinouts .................................................................................. 50

Limited Warranty ................................................................................... 53

Regulatory Compliance

Safety ............................................................................................................. 55

EMC ............................................................................................................... 56

Index ....................................................................................................... 59

Customer Support ................................................................................. 61

Technical Assistance ...................................................................................... 61

Product Service and Repair ............................................................................ 61

1

Introduction

Product Overview

The MS7580 Genesis is a high performance presentation area-imaging bar code

imager that utilizes CMOS imaging sensors for superior image quality. Genesis

utilizes custom decoder software, for reliable decoding of both 1D and 2D bar

code symbologies. Sharp images can be captured and transmitted in a variety of

outputs including: .jpg, .bmp, and .tiff.

Omnidirectional scanning capabilities and an excellent motion tolerance provides

aggressive scanning of all standard 1D, GS1 DataBar™ (RSS), PDF417,

microPDF, Composite, Matrix, and Postal Codes symbology types. Firmware

updates are easily loaded into Flash memory.

The MS7580 provides an extended scan volume and a built in object detection

sensor (IR) that instantly turns on the imager when an object is presented within

the imager’s field of view.

Genesis Interface Support

MS7580–124

Interfaces supported include:



• RS232

• USB

• Keyboard Wedge



• RS485 (External via Cable)



39

EAS equipped models are indicated with an EAS extension on the model number

(i.e., MS7580-124-EAS). See pages –47 for additional product information.

 USB is configurable for Keyboard Emulation Mode, Bi-Directional Serial Emulation

Mode or IBM OEM. The default USB setting is Keyboard Emulation Mode.

 Applicable for IBM®

Note: Standard models ship with the ability to read all 1D, PDF, and 2D bar

codes. Decoding and functional capability is limited and imagers will

not support key features including, but not limited to, the ability to

decode PDF, 2D or OCR fonts without proper limited use licenses

provided by Honeywell. If you wish to purchase a limited license for one

or more of the key features not included in the standard imager, please

specify at the time of sale or otherwise contact a customer service

representative for more information.

host applications.

2

Base Kit Components

Part # Description

MS7580-124 Genesis 7580 Presentation Area Imager



00-02544 MetroSelect™ Single-Line Configuration Guide



00-05252



Area-Imaging Supplemental Configuration Guide*



GEN-7580-UG Genesis 7580 User’s Guide*





39

EAS equipped models are indicated with an EAS extension on the model number

(i.e., MS7580-124-EAS). See pages –47 for additional product information.

 www.honeywellaidc.com Manuals are available for download from .

Optional Accessories

Part # Description

AC to DC Power Transformer - Regulated 12VDC @ 1.25A output.

46-00862 90VAC to 255VAC United States, Canada and Japan

46-00863 90VAC to 255VAC Continental European

46-00864 90VAC to 255VAC United Kingdom

46-00865 90VAC to 255VAC China

46-00866 90VAC to 255VAC Australia

Other items may be ordered for the specific protocol being used. To order additional items,

contact the dealer, distributor, or customer service. See page 61 for contact information.

3

Part # Description

The MS7580 requires a cable designed for a 12VDC area imager.

Do not attempt to use any cables other than the specified cables listed below

(cable series 5S-5Sxxx). Any damage incurred from incorrect cable usage

will void the limited warranty shown on page

Cable Compatibility Warning

53.

5S-5S000-3 RS232 12V VLink Cable with Built in Power Jack

Straight Black Cable with Short Strain Relief

5S-5S002-3 Keyboard Wedge 12V VLink Cable with Adapter Cable

Straight Black Cable with Short Strain Relief

5S-5S213-N-3

USB Direct Cable for 12V Host Power

Locking Plus-Power™ Type A Connector

Straight Black Cable with Short Strain Relief

5S-5S235-3

USB 12V VLink Cable with Built in Power Jack

Non-Locking Type A Connector

Straight Black Cable with Short Strain Relief

MX-RS485-5S006-3

RS485 Voltage Converter Cable with Build in Power

Jack

Straight Black Cable with Short Strain Relief

The following MS7580-124-EAS cables are compatible with Checkpoint

®

39

System devices. For additional cable information for the MS7580-124-EAS,

refer pages –47.

MX-5S114-E-3 RS232 12V VLink Straight, Black Cable

with Built in Power Jack

MX-5S236-E-3 USB 12V VLink Straight Black Cable with

Built in Power Jack, Non-Locking Type A Connector

46-00911 MS7580 Wall Mount Adapter Kit

46-00913 MS7580 Wall Mount Kit

00-05250 MS7580 Wall Mount Installation Guide

Other items may be ordered for the specific protocol being used. To order additional items,

contact the dealer, distributor, or customer service. See page 61 for contact information.

4

MS7580 Components

Item Item Description

1 Blue and White LED

See Visual Indicators (on page 20)

2 Button Mode Select Button

3 Speaker See Audible Indicators (on page 19)

4 Window LED Aperture

5 Adjustable Base

6 Cable Connection 10-pin RJ45, Female Socket,

See Imager Pinout Connections (on page 49)

7 Cable Release See Cable Installation and Removal (on page 6)

Note: The MS7580-124-EAS model is equipped with an integrated antenna

for Electronic Article Surveillance (EAS) system support. See pages

39–47 for additional product information.

Figure 1. Imager Components

5

Labels

Each MS7580 has a label located near the top of the output window. This label

provides the imager’s model number, date of manufacture, serial number, CE

and caution information. Additional information has been molded into the

underside of the imager's case. The following figure gives an example of the

label and the molded text with their locations identified.

Figure 2. Label and Molded Text Samples

For North America:

CAUTION: To maintain compliance with applicable standards, all circuits

connected to the scanner must meet the requirements of a NEC Class 2

power source or Limited Power Source as defined in UL 60950-1 Clause 2.5.

For Other Countries:

CAUTION: To maintain compliance with applicable standards, all circuits

connected to the scanner must meet the requirements of a Limited Power

Source as defined in IEC 60950-1 Clause 2.5.

Maintenance

Smudges and dirt on the imager's window can interfere with the imager's

performance. If the window requires cleaning, use only a mild glass cleaner

containing no ammonia. When cleaning the window, spray the cleaner onto a lint

free, non-abrasive cleaning cloth and then gently wipe the window clean.

If the imager's case requires cleaning, use a mild cleaning agent that does not

contain strong oxidizing chemicals. Strong cleaning agents may discolor or

damage the imager's exterior.

6

Cable Installation and Removal

Installation

1. Insert the cable’s modular connector into the socket on the imager.

2. Pull gently on the cable strain relief to ensure the cable is installed.

Note: If the cable is not fully latched, the imager may power intermittently.

Figure 3. Installing the Cable

Removal

Turn the host power off and disconnect the power supply from the cable before

attempting to disconnect the cable from the imager.

1. Locate the small pinhole on the imager near the cable connection point.

2. Bend a paperclip into the shape shown below.

3. Insert the paperclip into the pinhole and apply pressure to release the

connector lock.

4. Pull gently on the strain-relief of the cable to remove the cable from the

imager.

Figure 4. Disconnecting the Cable

MS7580-124-EAS Model Note

See page 39 for additional cable installation/removal instructions specific to the

MS7580-124-EAS Genesis with integrated RF EAS antenna.

7

Interface Installation

RS232

1. Turn off power to the host device.

2. Plug the interface cable’s modular

connector into the socket on the imager.

3. Connect the other end of the cable to a

dedicated COM port on the host device.

4. Plug the 12V power supply

into the

power jack on the cable.

5. Check the AC input requirements

of the power supply to verify the voltage

matches the AC outlet. The outlet must

be located near the equipment and

easily accessible.

6. Connect AC power

7. The MS7580 will start to initialize.

The white and blue LED will alternately

fade on and off for three seconds.

When the imager has finished

initializing, the imager will flash the white

LED three times while simultaneously

beeping three times. The low intensity

blue LED will remain turned on.

to the transformer.

8. Turn on power to the host device.

Installation Notes

• MS7580-124-EAS models are equipped with an integrated RF EAS

antenna. See page 39 for additional cable installation instructions for

EAS equipped Genesis models.

• Plugging the imager into a port on the host system does not guarantee

that scanned information will be communicated properly to the host

system. The imager is shipped from the factory configured with default

settings. Please refer to the MetroSelect Single-Line Configuration

Guide (PN 00-02544) or MetroSet™2’s help files for instructions on

changing the imager’s configuration. In addition, please check that the

imager and host system are using the same communication protocol.



Figure 5. RS232

The MS7580 requires 12V power to function for RS232 operation. Honeywell

recommends using the external power supply shipped with the MS7580.

See caution on page 5.

8

Keyboard Wedge

1. Turn off power to the host device.

2. Plug the interface cable’s modular

connector into the socket on the imager.

3. Disconnect the keyboard from the

host device.

4. Connect the “Y” ends of the

communication cable to the keyboard

and the keyboard port on the host

device. A male/female adapter cable is

supplied with the imager kit.

5. Plug the 12V power supply

6. Check the AC input requirements of the

power supply to verify the voltage

matches the AC outlet. The outlet must

be located near the equipment and be

easily accessible.

into the

power jack on the cable.

7. Connect AC power to the transformer.

8. The MS7580 will start to initialize. The

white and blue LED will alternately fade

on and off for three seconds. When the

imager has finished initializing, the

imager will flash the white LED three

times while simultaneously beeping

three times. The low intensity blue LED

will remain turned on.

9. Turn on power to the host device.

Installation Note

Plugging the imager into a port on the host system does not guarantee that

scanned information will be communicated properly to the host system. The

imager is shipped from the factory configured with default settings. Please refer

to the MetroSelect Single-Line Configuration Guide (PN 00-02544) or

MetroSet2’s help files for instructions on changing the imager’s configuration. In

addition, please check that the imager and host system are using the same

communication protocol.



Figure 6. Keyboard Wedge

The MS7580 requires 12V power to function for Keyboard Wedge operation.

See caution on page 5.

9

RS485

1. Turn off power to the host device.

2. Plug the interface cable’s modular

connector into the socket on the imager.

3. Connect the other end of the cable to

proper COM port of the host device

4. Turn on power to the host device.

.

5. The MS7580 will start to initialize.

The white and blue LED will alternately

fade on and off for three seconds.

When the imager has finished

initializing, the imager will flash the white

LED three times while simultaneously

beeping three times. The low intensity

blue LED will remain turned on.

Installation Note

Plugging the imager into a port on the host system does not guarantee that

scanned information will be communicated properly to the host system.

The imager is shipped from the factory configured with default settings.

Please refer to the MetroSelect Single-Line Configuration Guide (PN 00-02544)

or MetroSet2’s help files for instructions on changing the imager’s configuration.

In addition, please check that the imager and host system are using the same

communication protocol.



Figure 7. RS485

The MS7580 requires 12V power from the host for RS485 operation.

10

USB

1. Turn off power to the host device.

2. Plug the interface cable’s modular

connector into the socket on the

imager.

3. Plug the USB end of the cable into

the host’s USB port.

Steps 4–6 are for VLink cables with a

built in power jack and 12V external

power supply. Skip to step 6 for USB

direct connect cables

4. Plug the power supply into the

power jack on the VLink cable.

receiving 12V

power from the host.

5. Check the AC input requirements

of the power supply to verify the

voltage matches the AC outlet.

The outlet must be located near the

equipment and be easily

accessible.

6. Connect AC power to the transformer.

7. Turn on power to the host device.

8. The MS7580 will start to initialize. The

white and blue LED will alternately fade

on and off for three seconds. When the

imager has finished initializing, the

imager will flash the white LED three

times while simultaneously beeping

three times. The low intensity blue LED

will remain turned on.

Installation Notes

• MS7580-124-EAS models are equipped with an integrated RF EAS

antenna. See page 39 for additional installation instructions for MS7580-

124-EAS models.

• The MS7580 meets the requirements for Full Speed USB hardware.

The USB interface is configurable for Keyboard Emulation Mode,

Bi-Directional Serial Emulation Mode or IBM OEM. The default setting

for the USB interface is Keyboard Emulation Mode.



3

The MS7580 requires 12V power from the host for pass-through capabilities to function.

See page for a complete list of USB cable options.

Figure 8. USB

See caution on page 5.

11

• For information on configuring the MS7580 for USB Serial Emulation

Mode or IBM OEM, refer to the USB section of the MetroSelect

Single-Line Configuration Guide (PN 00-02544).

• Plugging the imager into a port on the host device does not guarantee

that scanned information will be communicated properly to the host

device. The imager is shipped from the factory configured with default

settings. Please refer to the MetroSelect Single-Line Configuration

Guide (PN 00-02544) or MetroSet2’s help files for instructions on

changing the imager’s configuration. In addition, please check that the

imager and host system are using the same communication protocol.

12

13

Mounting the MS7580

Components of Adapter Kit 46-00911

Item Item Description Qty.

A

Adapter Plate

1

B Locking Plate 1

C Base Cover 1

D

M3 x .5 - 10 mm Flat Head Phillips Screw

4

E

M3 x .5 - 8 mm Flat Head Phillips Screw

4

F #7 x 1.00 in. FHP Wood Screw 3

G MS7580 Wall Mount Installation Guide 1

Figure 9. 46-00911 Kit Components

Components of Wall Mount Kit 46-00913

Item Item Description Qty.

A Wall Mount 1

B #7 x 1.00 in. FHP Wood Screw 2

C

MS7580 Wall Mount Installation Guide

1

Figure 10. 46-00913 Kit Components

14

Installation of Adapter Kit 46-00911

1. Remove the rubber feet on the bottom of the MS7580.

2. Attach the adapter plate to the bottom of the imager with the four

M3 x .5 x 10 mm screws (  ) provided in the kit.

3. Attach the base plate to the adapter plate with the four M3 x .5 x 8 mm

screws (  ) provided in the kit.

Figure 11

4. Before mounting the locking plate, consider the position the imager will rest

when fully installed. There are two tabs located on the locking plate.

These tabs indicate the two directions the imager may face when locked

into position (see figure below).

Figure 12

15

5. Use the locking plate as a guide to drill three #39 pilot holes (A) in the

mounting surface.

Figure 13. Locking Plate (Not Drawn to Scale)

6. Secure the locking plate to the wall with the three #7 wood screws ()

provided in the kit.

Figure 14

7. Position the imager so the base plate sits flush over the locking plate.

Twist the imager 90° counter-clockwise to lock the imager into place.

Figure 15

16

Installation of Wall Mount Kit 46-00913

1. Drill two #39 pilot holes in the mounting surface. The pilot holes should be

centered vertically 44 mm apart.

2. Position the wall mount over the pilot holes with the arrow pointing up.

3. Secure the wall mount to the wall with the two #7 wood screws () provided

in the kit.

Figure 16

4. Slide the imager's base under the upper corner tabs on the wall mount.

5. Slide the remainder of the base in and down behind the lower corner tabs.

Figure 17

17

Operation

Modes of Operation

The MS7580 supports two standard modes of operation for scanning bar codes,

automatic activation and manual activation scanning. Scanning while in the

automatic activation mode can occur in either one of two configurable options,

pass-through or presentation. Both the pass-through and the presentation

options are enabled by default.

Automatic Activation Mode

With the default configuration, the imager

operates in the pass-through state for 300 ms and then changes to the

presentation state for additional decoding capability.

Pass-through Scanning

Scanning method:

–The imager decodes only 1D and PDF bar codes.

1. Pass the bar code through the active scan area to scan, decode and

send data.

Presentation Scanning–The imager decodes all 1D, PDF and 2D matrix codes

Scanning method:

1. Place the object in the IR activation range.

2. Hold the object's bar code in front of the scan window within the active

scan area to scan, decode and send data.

Manual Activation

The imager decodes all 1D, PDF and 2D matrix codes.



Scanning method:

1. Press the button one time to activate linear targeting.

2. Press the button one time to activate linear targeting.

 The MS7580 requires 12V power for pass-through capabilities to function.

 The default configuration is recommended for optimum scan performance.



Imager configuration bar codes require the manual activation mode.

18

3. Press the button one time to activate linear targeting.

4. Align the linear targeting line over the desired bar code.

Note: When scanning 1D bar codes, the bar code must be presented to

the imager in the correct orientation, see Figure 18. PDF and 2D

matrix codes may be presented in any orientation.

Figure 18. 1D Bar Code Orientation

5. Press button a second time to decode and send the data

6. The imager will return to the default presentation mode by either the

default time length or by double pressing the button.

Note: Decoding and functional capability of the imager is restricted through the

use of license numbers provided by Honeywell. Imagers will not support

key features such as, but not limited to, the ability to decode PDF, 2D or

OCR fonts without proper licenses. If you wish to purchase a limited

license for one or more of the key features not included in the standard

imager, please specify at the time of sale or otherwise contact a customer

service representative for more information. Standard models ship with

the ability to read all 1D, PDF, and 2D bar codes. OCR fonts are disabled

by default and must be specifically requested at an additional cost.

19

Audible Indicators

The MS7580 provides audible feedback during operation. The audible feedback

indicates the status of the imager. Eight settings are available for the tone of the

beep (normal, 6 alternate tones and no tone). To change the tone, refer to the

MetroSelect Single-Line Configuration Guide, PN 00-02544 or MetroSet2’s

help files.

One Beep

When the imager successfully reads a bar code the imager will beep once and

the white LED will flash once indicating data has been transmitted successfully.

The blue LED will return to the low intensity state if no other objects are

presented in the active scan area.

If the imager does not beep once and the white light does not flash, then the bar

code has not been successfully read.

Short Razzberry Tone

This tone is a failure indicator (see Failure Modes on page 21).

Long Razzberry Tone

This tone is a failure indicator (see Failure Modes on page 21).

Three Beeps - At Power Up

When the MS7580 first receives power it will start an initialization sequence.

The white and blue LEDs will alternately fade on and off for approximately

3 seconds. When the imager has finished initializing the white LED will flash

three times while simultaneously beeping three times to indicate the imager is

ready for use.

Three Beeps - Configuration Mode

When entering configuration mode, the white LED will flash while the imager

simultaneously beeps three times. The white and blue LEDs will continue to

flash while in this mode. Upon exiting configuration mode, the imager will beep

three times, and the LEDs will stop flashing.

When configured, 3 beeps can also indicate a communications timeout during

normal scanning mode.

When using single-code-configuring, the imager will beep three times:

a normal tone followed by a short pause, a high tone and then a low tone.

This indicates that the single configuration bar code has successfully configured

the imager.

20

Visual Indicators

The imager has blue and white LED

indicators surrounding the button on the

top of the imager. When the imager is on,

the intensity of the LED and the flashing or

stationary activity of the LEDs, indicates

the status of the current scan and the

diagnostic imager.

No LEDs are Illuminated

The LEDs will not be illuminated if the imager is not receiving power from the

host or transformer.

Steady Low Intensity Blue

The imager is in stand-by mode. Present a bar code to the imager and the blue

LED will switch to a high intensity blue when the IR detects the object.

Steady High Intensity Blue

The high intensity blue LED is illuminated when the imager is active and

attempting to decode a barcode.

Single White Flash

When the imager successfully reads a bar code the imager will beep once and

the white LED will flash once indicating data has been transmitted successfully.

The blue LED will return to the low intensity state if no other objects are

presented in the active scan area.

If the imager does not beep once and the white light does not flash, then the bar

code has not been successfully read.

Steady White

When the imager successfully reads a bar code it will beep once and the white

LED will turn on indicating data is being transmitted.

Note: After a successful scan, the imager transmits the data to the host device.

Some communication modes require that the host inform the imager when

data is ready to be received. If the host is not ready to accept the

information, the imager’s white LED will remain on until the data can

be transmitted.

Alternating Flashing of Blue and White

This indicates the imager is in configuration mode. A short razzberry tone

indicates that an invalid bar code has been scanned while in this mode.

Figure 19.

21

Failure Modes

Long Razzberry Tone – During Power Up

Failed to initialize or configure the imager. If the imager does not respond after

reconfiguration, return the imager for repair.

Short Razzberry Tone – During Scanning

An Invalid bar code has been scanned when in configuration mode.

22

Field of View

Figure 20. Field of View

23

Depth of Field by Minimum Bar Code Element Width

Minimum Bar Code Element Width

1D PDF

QR+

Datamatrix

A B C D F G

mm

.13 .19 .26 .33 .25 .38

mils

5.0 7.5 10.4 13 10 15

Figure 21. Depth of Field by Minimum Bar Code Element Width

Note: Standard models ship with the ability to read all 1D, PDF and 2D bar

codes. Decoding and functional capability is limited and imagers will not

support key features including, but not limited to, the ability to decode

PDF, 2D or OCR fonts without proper limited use licenses provided by

Honeywell. If you wish to purchase a limited license for one or more of the

key features not included in the standard imager, please specify at the

time of sale or otherwise contact a customer service representative for

more information.

24

IR Activation Range

The MS7580 has a built in object detection sensor that instantly turns on the

imager when an object is presented within the imager’s IR Activation Area,

shown below.

Figure 22. IR Activation Area

25

Illumination Source

Figure 23. Illumination Source

26

IR Source

Figure 24. IR Source

27

Targeting Source

Figure 25. Targeting Source

28

29

Troubleshooting Guide

The following troubleshooting guide is for reference purposes only. Contact a

customer service representative or technical support representative to preserve

the limited warranty terms. See page 61 for contact information.

All Interfaces

Symptoms Possible Causes Solution

No LEDs, beep

or illumination

No power is being

supplied to the

imager.

Check transformer, outlet, and

power strip. Make sure the cable

is plugged into the imager.

No power is being

supplied to the

imager from the host.

Some host systems cannot supply

enough current to power the

MS7580. A power supply may be

required.

Long Razz tone

on power up

There has been a

imager configuration

failure.

Contact a customer service

representative, if the imager will

not hold the saved configuration.

There has been a

diagnostic failure.

Contact a customer service

representative, if the imager will

not function.

Long Razz tone

when exiting

configuration

mode

There was a failure

saving the new

configuration.

Re-try to configure the imager.

Contact a customer service

representative if the imager will not

hold the saved configuration.

Long Razz tone

There is a scanning

mechanism failure.

Contact a customer service

representative.

Short Razz tone

in configuration

mode

An invalid bar code

has been scanned.

Scan a valid bar code or quit

configuration mode.

30

Symptoms Possible Causes Solution

The imager

powers up, but

does not beep

when bar code is

scanned.

The beeper is

disabled and no tone

is selected.

Enable the beeper and select a

tone.

The imager

powers up, but

does not scan

and/or beep.

The bar code

symbology trying to

be scanned is not

enabled.

UPC/EAN, Code 39, interleaved 2

of 5, Code 93, Code 128, Codabar

and PDF are enabled by default.

Verify that the type of bar code

being read has been selected.

The imager

powers up, but

does not scan

and/or beep.

The imager is trying

to scan a barcode that

does not match the

configured criteria.

Verify that the bar code being

scanned falls into the configured

criteria (i.e. character length lock or

minimum bar code length settings).

The following item is only relevant for RS232 and Serial USB Interfaces.

The imager

scans a bar

code, but locks

up after the first

scan and the

white LED stays

on.

The imager is

configured to support

some form of host

handshaking but is not

receiving the signal.

If the imager is setup to support

ACK/NAK, RTS/CTS, or

XON/XOFF, verify that the host

cable and host are supporting the

handshaking properly.

The imager

scans, but the

data transmitted

to the host is

incorrect.

The imager’s data

format does not

match the host

system requirements.

Verify that the imager’s data

format matches that required by

the host. Make sure that the

imager is connected to the proper

host port.

31

Symptoms Possible Causes Solution

The imager

beeps at some

bar codes and

NOT for others

of the same bar

code symbology.

The bar code may

have been printed

incorrectly.

Check if it is a check

digit/character/or border problem.

The imager is not

configured correctly

for this type of bar

code.

Check if check digits are set

properly.

The minimum symbol

length setting does

not work with the bar

code.

Check if the correct minimum

symbol length is set.

The imager

scans the bar

code but there

is no data.

The configuration is

not set correctly.

Make sure the imager is

configured

for the appropriate mode.

The next four items are only relevant for a Keyboard Wedge interface.

The imager

scans but the

data is not

correct.

The configuration is

not set correctly.

Make sure that the proper PC type

AT, or PS2 is selected. Verify

correct country code and data

formatting are selected. Adjust

inter-character delay symptom.

The imager is

transmitting each

character twice.

The configuration is

not set correctly.

Increase interscan code delay

setting. Adjust whether the F0

break is transmitted. It may be

necessary to try this in both

settings.

Alpha characters

show as lower

case.

The computer is in

Caps Lock mode.

Enable Caps Lock detect setting

of the imager to detect if the PC is

operating in Caps Lock.

Everything works

except for a

couple of

characters.

These characters

may not be supported

by that country’s key

look up table.

Try operating the imager in Alt

mode.

32

Symptoms Possible Causes Solution

The imager

scans but the

data is not

correct.

The imager and host

may not be configured

for the same interface

parameters.

Check that the imager and the

host are configured for the same

interface parameters.

The following item is only relevant for an RS232 interface.

The imager

powers up OK

and scans OK

but does not

communicate

properly with

the host.

The com port at the

host is not working or

not configured

properly.

Check to make sure that the baud

rate and parity of the imager and

the communication port match

and the program is looking for

“RS232” data.

The imager

powers up OK

and scans OK

but does not

communicate

properly with

the host.

The cable is not

connected to the

correct com port.

Check to make sure that the cable

is connected to the correct com

port.

Characters are

being dropped.

Inter-character delay

needs to be added to

the transmitted output.

Add some inter-character delay to

the transmitted output by using

the Configuration Guides

(PN 00-02544 and 00-05252).

The following item is only relevant for a USB interface.

No LEDs, beep

or Illumination

The USB host may not

be active.

The MS7580 will not

operate from hub/host

power without host

communication.

Turn on the host device.

The imager is not

receiving sufficient

power to support

operation.

Refer to the electrical

specifications on page 34.

Verify adequate power is being

supplied to the imager.

33

Design Specifications

Operational

Light Source: LED 645 nm ±7.5 nm

Pulse Duration: Up to 600µs (Default)

Maximum Output

of the LED:

Maximum 70 mA emits 5800 mlm

Depth of Scan Field: 0 mm – 158 mm (0" – 6.2") for 0.33 mm (13 mil)

Field of View:

51 mm x 31 mm (2.0" x 1.2") @ Face / Window

184 mm x 109 mm (7.2" x 4.3") @ 158 mm (6.2") from

Face

Minimum Element

Width:

1D 0.1 mm (4 mil)

2D 0.254 mm (10 mil)

Resolution: 832 x 504 Pixels

Infrared Activation

Range: 0 mm (0") face to 152 mm (6")

Optional Decode and

Imaging Capabilities:

Autodiscriminates all Standard 1-D, RSS, PDF417,

microPDF, MaxiCode, Data Matrix, QR Code, UCC,

EAN Composites, Postals, Aztec

(Image Transfer) – BMP, TIFF, or JPEG output on

USB and RS232 Interfaces

System Interfaces:

PC Keyboard Wedge, RS232, USB, RS485 (external

via cable)

Print Contrast: 20% Minimum Reflectance Difference

Number Characters

Read:

4096 Bytes Maximum

Beeper Operation: 7 tones or no beep

Indicators (LED)

Default Settings:

High Intensity Blue

The imager is active and attempting

to scan.

Low Intensity Blue The imager is idle.

White Good Read

34

Mechanical

Height (H): 150 mm (5.91")

Width (W): 83 mm (3.27")

Depth (D): 80 mm (3.15")

Weight:

340 g ± 15 g

(12 oz. ± 5 oz.)

Termination: 10 pin modular RJ45

Electrical

+12 Volt

Adapter Value

+5 Volt

USB Power Value

Input Voltage: 12VDC ± 0.25V 5VDC ± 0.25V

Power:

Peak 2.0 W (Typical)

 1.6 W (Typical)

Operating 1.7 W (Typical) 1.4 W (Typical)

Idle 1.3 W (Typical) 1.0 W (Typical)

Current:

Peak 167 mA (Typical)

 320 mA (Typical)

Operation 142 mA (Typical) 280 mA (Typical)

Idle 109 mA (Typical) 200 mA (Typical)



DC Transformer:

Peak Values of at least 1 ms in width.

Class 2; 12VDC @ 1.25 A

For regulatory compliance information see pages 55–58

Environmental

Temperature: Operating = 0°C to 40° (32° to 104°F)

Storage = -40°C to 60°C (-40°F to 140°F)

Humidity: 0% to 95% Relative Humidity, Non-Condensing

Light Levels: Up to 100,000 Lux

Shock: Designed to withstand 1.5 m (5 ft.) drops

Contaminants: Sealed to resist airborne particulate contaminants

Ventilation: None required

35

Applications and Protocols

The model number on each imager includes the imager number and factory

default communications protocol.

Imager Version Identifier Communication Protocol(s)

MS7580 124

Interfaces supported include:

• RS232 (TXD, RXD, RTS

• USB

, CTS)

• Keyboard Wedge



• RS485 (External via Cable)



TXD and RTS are transmitted at TTL levels. Contact a customer service

representative for information on additional RS232 options.



USB is configurable for Keyboard Emulation Mode, Bi-Directional Serial Emulation

Mode or IBM OEM. The default USB setting is Keyboard Emulation Mode.

The MS7580 with a built-in PC Keyboard Wedge interface is designed for

Keyboard emulation use only. Many RS232 configurable functions, available in

other Honeywell imagers, are also available as keyboard wedge functions.

The following are the most important selectable options specific to the keyboard

wedge.

Keyboard Type

• *AT (includes IBM® PS2 models 50, 55, 60, 80)

• IBM PS2 (includes models 30, 70, 8556)

Keyboard Country Type

• *USA

• Italian

• Swiss

• Belgian

• Japanese

• Swedish/Finnish

• French

• Russian Cyrillic

• Turkish

•

German

•

Slovenian

•

United Kingdom

•

Hungarian

•

Spanish

* Indicates a default setting. For information on how to change the default

settings, refer to the help files in MetroSet2, the MetroSelect Single-Line

Configuration Guide or the Area-Imaging Supplemental Configuration Guide.

36

37

Configuration and Upgrades

Configuration Modes

The MS7580 has three modes of configuration.

• Bar Codes

The MS7580 can be configured by scanning the bar codes included

in the MetroSelect Single-Line Configuration Guide or the Area-Imaging

Supplemental Configuration Guide. The manuals are available for download

at www.honeywellaidc.com.

• MetroSet2

This user-friendly Windows®

www.honeywellaidc.com

-based configuration program allows you to

simply ‘point-and-click’ at the desired imager options. MetroSet2 is available

for download at .

• Serial Programming

This mode of configuration is ideal for OEM applications. Serial

programming mode gives the end-user the ability to send a series of

commands using the serial port of the host system. The commands are

equivalent to the numerical values of the bar codes located in the

MetroSelect Single-Line Configuration Guide.

Upgrading the Firmware

The MS7580 is part of Honeywell’s line of imagers with flash upgradeable

firmware. The upgrade process requires, a new firmware file supplied to the

customer by a customer service representative and Honeywell’s MetroSet2

software. A personal computer running Windows®

Note: Do not use the standard cable supplied with Keyboard Wedge or RS485

MS7580 interface kits for firmware upgrades. If using USB or RS232 for

the upgrade process, the standard USB or RS232 cable provided with the

imager can be used.

95 or greater with an

available RS232 serial or USB port is required to complete the upgrade.

 See Contact Information on page 61.



www.honeywellaidc.com

MetroSet2 is available for download, at no additional cost, from

.

38

To upgrade the firmware in the MS7580:

1. Plug the imager into a serial communication port on the host system.

2. Start the MetroSet2 software.

3. Click on the plus sign (+) next to POS Scanners to expand the supported

imager list.

4. Choose the MS7580 Genesis from the list.

5. Click on the Configure Genesis/7580 Scanner button.

6. Choose Flash Utility from the options list located on the left side of the

screen.

7. Click on the Open File button in the Flash Utility window.

8. Locate and open the flash upgrade file.

9. Select the COM port that the imager is connected to on the host system.

10. Verify the settings listed in the Flash Utility window.

11. Click on the Flash Imager button to begin the flash upgrade. A message

will appear on the screen when the upgrade is complete.

39

MS7580-124-EAS Model

MS7580-124-EAS models are equipped with an integrated antenna for Electronic

Article Surveillance (EAS) system support. The following information should be

used in conjunction with the manufacturer’s EAS system documentation for

successful integration of an MS7580-124-EAS Genesis.

Integrated RF EAS Antenna Connection

The following information is applicable for MS7580-124-EAS kits containing an

RS232, MX-5S114-E-3 cable or a USB, MX-5S236-E-3 cable.

Insert the cable’s EAS connector into the antenna connector on the imager.

There will be an audible click when the connector lock engages.

Figure 26. Antenna Connect

40

EAS System Connection

The following information should be used in conjunction with the manufacturer’s

documentation EAS system.

Checkpoint®

Honeywell cables compatible with Checkpoint EAS systems include five

additional wires for device connection*. Consult the table below for the

appropriate wire and terminal configuration.

EAS System Integration

Antenna and Interlock†

Cable

(MX-5S236-E-3 or MX-5S114-E-3)

Connection

Checkpoint Device

Wire Color Wire Gauge Connection Type

Solid Light Green Thin INTLK + Terminal Interlock†

Solid Black

Thin INTLK - Terminal, GND

Red and White Thick Antenna + Terminal

Antenna

Black and White Thick Antenna - Terminal

No Insulation/Shield Antenna Shield

† Interlock functionality requires specific EAS device settings. Consult the

manufacturer’s EAS system documentation for the appropriate switch and timing

potentiometer settings.

* Caution Statements

For North America:

Caution: To maintain compliance with applicable standards, all circuits

connected to the scanner must meet the requirements of a NEC

Class 2 power source or Limited Power Source as defined in UL

60950-1 2nd edition Clause 2.5.

For Other Countries:

Caution: To maintain compliance with applicable standards, all circuits

connected to the scanner must meet the requirements of a Limited

Power Source as defined in IEC 60950-1 2nd edition Clause 2.5.

41

Inside the Checkpoint device, two switch banks set the deactivation antenna

tuning. The recommended settings for the switch banks are shown below.

See page 44 for tag deactivation guidelines.

Switch Bank Settings

SW1

SW2

Switches 1 - 6

OFF

Switches 1 - 6

OFF

Settings of 0pF to 47pF are recommended to achieve a maximum

deactivation range.

42

Configuration for EAS Applications

EAS support is disabled by default in the MS7580-124-EAS series. To enable

EAS support the imager must be configured for a system type and signal mode.

Follow the configuration sequence below to configure the imager for EAS

functionality.

1. Scan the system type bar code below to enable EAS system support.

Enable Checkpoint System EAS Support

³ 3 3 7 2 2 0

2. Scan either the Enable Continuous Mode bar code or

Regular Mode

In regular EAS mode, the imager will signal the EAS system to

activate immediately after the area imager successfully transmits a

bar code. The imager will also signal the EAS system to deactivate

after the configured EAS timeout expires.

the Enable Regular

Mode bar code.

Note: If regular mode is enabled an EAS timeout length will need to

be configured (see page 43).

Enable Regular Mode

³ 1 4 6 1 0 5

Continuous Mode

In continuous mode, the imager will signal the EAS system to activate

when it first powers on. The area imager will never deactivate the

EAS system while in continuous mode. The EAS timeout setting has

no effect in continuous mode.

Enable Continuous Mode

³ 1 4 6 1 1 5

43

3. Scan the desired EAS timeout length (applicable for regular mode only).

The EAS timeout length specifies the maximum time that the area imager

will leave the EAS interlock signal asserted following a successful scan. The

EAS timeout setting has no effect in continuous mode.

Note: If the area imager routinely fails to deactivate EAS tags, increase the

value of the timeout setting.

EAS Timeout 100 ms

³ 8 4 6 0 0 0

EAS Timeout 500 ms

³ 8 4 6 0 5 0

EAS Timeout 1s

³ 8 4 6 0 1 0 0

EAS Timeout 5s

³ 8 4 6 0 5 0 0

To Disable EAS Support

Scan the bar code below to disable EAS support.

Disable EAS Support

³ 3 3 7 2 0 0

44

EAS Tag Deactivation Range

Antenna Precaution

The integrated EAS antenna is built into the stand/base of the imager. Do not

enclose or rest the imager’s base in close proximity to dense metal. The metal

may interfere with the antenna decreasing the expected deactivation range.

Tag Storage Precaution

Do not store tags within 45.7 cm [18.0″] of the MS7580. Tags stored closer than

45.7 cm [18.0″] may be unintentionally deactivated. The precautionary area

includes storage areas located under the MS7580.

Deactivation Range

Proper tag deactivation requires the entire tag to pass through the expected tag

deactivation range indicated in figures 27 (below) and 28 (on page 45).

Figure 27. Expected Tag Deactivation Area (Side View)

45

Figure 28. Expected Tag Deactivation Area (Top View)

46

Imager Pinouts–MS7580-124-EAS

Figure 29. MS7580-124-EAS, 10-Pin Female Modular Socket

RS232

USB

Pin



Function Pin Function

1

Signal/Power Ground

1

Signal/Power Ground

2

CTS Input

2

Tied to Pin 4 in Cable

3 RS232 Receive Input 3 No Connect

4 No Connect 4 Tied to Pin 2 in Cable

5 Reserved 5 Reserved

6 RTS Output 

6 USB D+

7

Reserved

7

+5VDC USB Power

8

RS232 Transmit Output



8

USB D-

9

+12V Power

9

+12V Power

10

Shield Ground

10

Shield Ground

SHELL

Signal/Power Ground

SHELL

Signal/Power Ground

Integrated RF EAS Antenna

(MS7580-124-EAS Models Only)

Figure 30. 2-Pin Box Receptacle

Pin Function

1

EAS ANT -

2 EAS ANT +

 

 Signals on Pin 6 and 8 are TTL full level RS232 output signals on MS7580-124-EAS

models.

USB requires 12V power for pass-through functionality.

47

Cable Pinouts (Host End)‡

RS232, 12V VLink Cable

MX-5S114-E-3

Pin Function

Figure 31. 9-Pin Female, D-Type

1 Shield Ground

2 RS232 Receive Output

3

RS232 Transmit Input

4 DSR

5 Power/Signal Ground

6 DTR

7

RTS

8 CTS

9 Host +12VDC

USB

MX-5S236-E-3

Pin Function

Figure 32. USB Type A, Non-Locking

1 PC +5V/V_USB

2 D-

3 D+

4 Ground

Antenna Disconnect

1. Press the release lock on the cable’s EAS connector.

2. Pull the connector free..

Figure 33. Antenna Disconnect

‡ MS7580-124-EAS compatible cables. For standard MS7580 cable pinouts refer

to page 50.

48

49

Imager and Cable Terminations

Standard Imager Pinouts‡

Figure 34. Back/Connector View of the MS7580

RS232

 Keyboard Wedge

Pin



Function Pin Function

1

Signal/Power Ground

1

Signal/Power Ground

2

CTS/DTR Input

2

Tied to Pin 3 in Cable

3

RS232 Receive Input

3

Tied to Pin 2 in Cable

4

No Connect

4

PC Data

5

No Connect

5

PC Clock

6

RTS Output



6

KB Clock

7

No Connect

7

+5VDC PC Keyboard Power

8 RS232 Transmit Output  8 KB Data

9 Adapter Power 9 Adapter Power

10

Shield Ground

10

Shield Ground

SHELL

Signal/Power Ground

SHELL

Signal/Power Ground

RS485

 USB

Pin



Function

Pin

Function

1

Signal/Power Ground

1

Signal/Power Ground

2

CTS

2

Tied to Pin 4 in Cable

3

RXD

3

No Connect

4

PC Data

4

Tied to Pin 2 in Cable

5

PC Clock

5

No Connect

6 KB Clock 6 USB D+

7 Keyboard/USB Power 7 +5VDC USB Power

8 TXD 8 USB D-

9 Adapter Power 9 Adapter Power

10

Shield Ground

10

Shield Ground

SHELL Signal/Power Ground

SHELL Signal/Power Ground

 RS485, RS232, and Keyboard Wedge interfaces require 12V power for operation.

 

 Signals on Pin 6 and 8 are TTL level RS232 output signals.

USB requires 12V power for pass-through functionality.

‡ See page 46 for pinout information specific to the MS7580-124-EAS Genesis model.

50

Standard Cable Pinouts‡

(Host End)

RS232, 12V VLink Cable

5S-5S000-3

Pin Function

9-Pin Female, D-Type

1 Shield Ground

2 RS232 Transmit Output

3 RS232 Receive Input

4 No Connect

5 Power/Signal Ground

6 Reserved

7 CTS Input

8 RTS Output

9 +12VDC

RS485

MX-RS485-5S006-3

Pin Function

SDL A Key Connector

1 Signal/Power Ground

2 IBM A+

3 IBM B-

4 +12VDC

USB

5S-5S213-3 or 5S-5S006-N-3

Pin Function

Type A

Non-Locking

Type A

Locking

Plus-Power

5S-5S235-N-3

USB Type A

Non-Locking

5S-5S213-3

USB Type A

Locking Plus-Power

1

1

PC +5V/V_USB

2 2 D-

3 3 D+

4 4 Ground

5 Ground

6 +12VDC

7-8 No Connect

‡ See page 47 for pinout information specific to the MS7580-124-EAS Genesis model.

51

Keyboard Wedge VLink Cable

5S-5S002-3

Pin Function

5-Pin DIN, Female

1 Keyboard Clock

2 Keyboard Data

3 No Connect

4 Power Ground

5 +5VDC

Pin

Function

6-Pin DIN, Male

1 PC Data

2 No Connect

3 Power Ground

4 +5VDC

5

PC Clock

6 No Connect

Honeywell will supply an adapter cable with a 5-pin DIN male connector on one

end and a 6-pin mini DIN female connector on the other. According to the

termination required, connect the appropriate end of the adapter cable to the

VLink cable, leaving the necessary termination exposed for connecting to the

keyboard and the keyboard port on the PC.

Keyboard Wedge Adapter Cable

Supplied with Cable 5S-5S002-3

Pin Function

5-Pin DIN, Male

1 PC Clock

2 PC Data

3 No Connect

4 Power Ground

5 +5VDC

Pin Function

6-pin Mini DIN, Female

1 Keyboard Data

2 No Connect

3 Power Ground

4 +5VDC

5 Keyboard Clock

6 No Connect

52

53

Limited Warranty

Honeywell International Inc. ("HII") warrants its products and optional

accessories to be free from defects in materials and workmanship and to

conform to HII’s published specifications applicable to the products purchased at

the time of shipment. This warranty does not cover any HII product which is (i)

improperly installed or used; (ii) damaged by accident or negligence, including

failure to follow the proper maintenance, service, and cleaning schedule; or (iii)

damaged as a result of (A) modification or alteration by the purchaser or other

party, (B) excessive voltage or current supplied to or drawn from the interface

connections, (C) static electricity or electro-static discharge, (D) operation under

conditions beyond the specified operating parameters, or (E) repair or service of

the product by anyone other than HII or its authorized representatives.

This warranty shall extend from the time of shipment for the duration published

by HII for the product at the time of purchase ("Warranty Period"). Any defective

product must be returned (at purchaser’s expense) during the Warranty Period to

HII factory or authorized service center for inspection. No product will be

accepted by HII without a Return Materials Authorization, which may be obtained

by contacting HII. In the event that the product is returned to HII or its authorized

service center within the Warranty Period and HII determines to its satisfaction

that the product is defective due to defects in materials or workmanship, HII, at

its sole option, will either repair or replace the product without charge, except for

return shipping to HII.

EXCEPT AS MAY BE OTHERWISE PROVIDED BY APPLICABLE LAW, THE

FOREGOING WARRANTY IS IN LIEU OF ALL OTHER COVENANTS OR

WARRANTIES, EITHER EXPRESSED OR IMPLIED, ORAL OR WRITTEN,

INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR NON-

INFRINGEMENT.

HII’S RESPONSIBILITY AND PURCHASER’S EXCLUSIVE REMEDY UNDER

THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE

DEFECTIVE PRODUCT WITH NEW OR REFURBISHED PARTS. IN NO

EVENT SHALL HII BE LIABLE FOR INDIRECT, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES, AND, IN NO EVENT, SHALL ANY LIABILITY

OF HII ARISING IN CONNECTION WITH ANY PRODUCT SOLD HEREUNDER

(WHETHER SUCH LIABILITY ARISES FROM A CLAIM BASED ON

CONTRACT, WARRANTY, TORT, OR OTHERWISE) EXCEED THE ACTUAL

AMOUNT PAID TO HII FOR THE PRODUCT. THESE LIMITATIONS ON

LIABILITY SHALL REMAIN IN FULL FORCE AND EFFECT EVEN WHEN HII

MAY HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH INJURIES,

LOSSES, OR DAMAGES. SOME STATES, PROVINCES, OR COUNTRIES DO

NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION

MAY NOT APPLY TO YOU.

54

All provisions of this Limited Warranty are separate and severable, which means

that if any provision is held invalid and unenforceable, such determination shall

not affect the validity of enforceability of the other provisions hereof. Use of any

peripherals not provided by the manufacturer may result in damage not covered

by this warranty. This includes but is not limited to: cables, power supplies,

cradles, and docking stations. HII extends these warranties only to the first end-

users of the products. These warranties are non-transferable.

The duration of the limited warranty for the MS7580 is two (2) year(s). The

accessories have a 90 day limited warranty from the date of manufacture.

55

Regulatory Compliance

Safety

ITE Equipment

IEC 60950-1:Second Edition, EN 60950-1:Second Edition

LED

IEC 62471-1: Exempt Risk Group

Caution

Use of controls or adjustments or performance of procedures other than those

specified herein may result in hazardous radiation exposure. Under no

circumstances should the customer attempt to service the LED scanner. Never

attempt to look at the LED beam, even if the scanner appears to be

nonfunctional. Never open the scanner in an attempt to look into the device.

Doing so could result in hazardous radiation exposure. The use of optical

instruments with the LED equipment will increase eye hazard.

Atención

La modificación de los procedimientos, o la utilización de controles o ajustes

distintos de los especificados aquí, pueden provocar una exposición de luz

brillante peligrosa. Bajo ninguna circunstancia el usuario deberá realizar el

mantenimiento del LED (Diodo Emisor de Luz) del lector. Ni intentar mirar al haz

del LED incluso cuando este no esté operativo. Tampoco deberá abrir el lector

para examinar el aparato. El hacerlo puede conllevar una exposición peligrosa a

la luz del LED. El uso de instrumentos ópticos con el equipo LED puede

incrementar el riesgo para la vista.

Attention

L'emploi de commandes, réglages ou procédés autres que ceux décrits ici peut

entraîner de graves irradiations. Le client ne doit en aucun cas essayer

d'entretenir lui-même le scanner ou la LED. Ne regardez jamais directement le

rayon LED, même si vous croyez que le scanner est inactif. N'ouvrez jamais le

scanner pour regarder dans l'appareil. Ce faisant, vous vous exposez à un risque

d’irradiation. L'emploi d'appareils optiques avec cet équipement à LED augmente

le risque d'endommagement de la vision.

Achtung

Die Verwendung anderer als der hier beschriebenen Steuerungen, Einstellungen

oder Verfahren kann eine gefährliche Licht emittierender Dioden strahlung

hervorrufen. Der Kunde sollte unter keinen Umständen versuchen, den Licht

emittierender Dioden-Scanner selbst zu warten. Sehen Sie niemals in den Licht

56

emittierender Diodenstrahl, selbst wenn Sie glauben, daß der Scanner nicht aktiv

ist. Öffnen Sie niemals den Scanner, um in das Gerät hineinzusehen.

Wenn Sie dies tun, können Sie sich einer gefährlichen Licht emittierender

Diodenstrahlung aussetzen. Der Einsatz optischer Geräte mit dieser

Laserausrüstung erhöht das Risiko einer Sehschädigung.

Attenzione

L'utilizzo di sistemi di controllo, di regolazioni o di procedimenti diversi da quelli

descritti nel presente Manuale può provocare delle rischiose esposizioni

radiattive. Il cliente non deve assolutamente tentare di riparare egli stesso lo

scanner LED (o diodo emettitore di luce). Non guardate mai il raggio LED (d.

emettitore di luce), anche se credete che lo scanner non sia attivo. Non aprite

mai lo scanner per guardare dentro l'apparecchio. Facendolo potete esporVi ad

una radiazione rischiosa. L'uso di apparecchi ottici, equipaggiati con raggi LED

(d. emettitori di luce), aumenta il rischio di danni alla vista.

EMC

Emissions

FCC Part 15, ICES-003, CISPR 22, EN 55022

Immunity

CISPR 24, EN 55024

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Class A Devices

The following is applicable when the scanner cable is greater in length than

3 meters (9.8 feet) when fully extended:

Les instructions ci-dessous s’appliquent aux cables de scanner dépassant

3 métres (9.8 pieds) de long en extension maximale:

Folgendes trifft zu, wenn das Scannerkabel länger als 3 Meter ist:

This equipment has been tested and found to comply with limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to

cause harmful interference, in which case the user will be required to correct the

interference at their own expense. Any unauthorized changes or modifications to

this equipment could void the user’s authority to operate this device.

57

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

Notice

This Class A digital apparatus complies with Canadian ICES-003.

Remarque

Cet appareil numérique de classe A est conforme à la norme

canadienne NMB-003.

Warning

This is a class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate

measures.

Warnung!

Dies ist eine Einrichtung der Klasse A. Diese Einrichtung kann im Wohnbereich

Funkstörungen verursachen. In diesem Fall kann vom Betreiber verlangt werden,

angemessene Massnahmen durchzuführen.

Attenzione

Questo e’ un prodotto di classe A. Se usato in vicinanza di residenze private

potrebbe causare interferenze radio che potrebbero richiedere all’utilizzatore

opportune misure.

Attention

Ce produit est de classe “A”. Dans un environnement domestique, ce produit

peut être la cause d’interférences radio. Dans ce cas l’utiliseteur peut être

amené à predre les mesures adéquates.

58

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Class B Devices

The following is applicable when the scanner cable is less than 3 meters

(9.8 feet) in length when fully extended:

Les instructions ci-dessous s’appliquent aux cables de scanner ne

dépassant pas 3 métres (9.8 pieds) de long en extension maximale:

Folgendes trifft zu, wenn das Scannerkabel kürzer als 3 Meter ist:

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Notice

This Class B digital apparatus complies with Canadian ICES-003.

Remarque

Cet appareil numérique de classe B est conforme à la norme

canadienne NMB-003.

59

Index

A

AC ................................. 2, 7–11, 34

Accessories ................................... 2

Adapter ........................ 2, 13, 14, 51

Aperture......................................... 4

Audible Indicator .............. 20–21, 38

Automatic Activation Mode .......... 17

B

Bar Code ............. 23, 29–32, 33, 37

Beep .............. 20–21, 29–32, 33, 38

Blue LED ........... 4, 7–11, 20–21, 38

Button .................... 4, 17, 18, 20, 37

C

Cable ............................................. 6

Keyboard Wedge ....... 3, 8, 50–51

RS232 ........................ 3, 7, 50–51

RS485 ........................ 3, 9, 50–51

Termination ................................ 4

USB ................... 3, 10, 11, 50–51

VLink .. 2, 3, 7–11, 29–32, 38, 50–

51

Caution .................................... 7–11

CE ....................................... 5, 7–11

Code Type ................. 17, 18, 23, 34

Compliance ....................... 7–11, 54

Configuration ....... 29–32, 35, 37, 38

Connector Pinouts ....................... 49

Current ........................................ 34

Customer Service ................ 2, 3, 54

D

DC ......................... 2, 34, 49, 50–51

Decode ........................................ 33

Default Parameters ..................... 35

Depth of Field .............................. 23

E

EAS ....................................... 44, 45

EMC ................................ 34, 56, 58

EMI .............................................. 56

Emissions .............................. 56, 58

F

Field of View ............................... 22

Firmware ..................................... 38

Flash ROM .................................. 38

H

Host ........................................ 7–11

I

Immunity ............................... 56, 58

Indicator

Audible .............. 4, 20–21, 33, 38

Failure ........................... 4, 20–21

Visual................. 4, 20–21, 33, 38

Interface .......................... 29–32, 33

Cable ....................... 7–11, 50–51

Keyboard Wedge ... 1, 3, 8, 35, 49

RS232 ................... 1, 3, 7, 35, 49

RS485 ....................... 3, 9, 35, 49

USB ................... 3, 10, 11, 35, 49

IR .......................................... 17, 24

K

Keyboard Country Type .............. 35

Keyboard Type ............................ 35

L

Labels ........................................... 5

LED ....................... 7–11, 29–32, 33

Blue ......................... 7–11, 20–21

White ....................... 7–11, 20–21

License ................................. 17, 18

Light Levels ................................. 34

Light Source ................................ 33

M

Maintenance ................................. 5

Manual Activation Mode ........ 17, 18

Manuals ........................................ 2

MetroSelect ................................. 37

MetroSet2 ................................... 38

60

P

Pass-Through .............................. 17

Pinouts ............................ 49, 50–51

Power .......................... 7–11, 34, 38

Power Supply ...................... 6, 7–11

Presentation ................................ 17

Protocols ..................................... 35

R

Razz .......................... 20–21, 29–32

Repair .......................................... 54

RMA ............................................ 54

S

SELV ....................................... 7–11

Service ........................................ 54

Specifications

Electrical .................................. 34

Environmental .......................... 34

Mechanical ............................... 34

Operational .............................. 33

Swiftdecoder™ .............................. 1

T

Tone ...................................... 20–21

Transformer .................. 2, 7–11, 34

Troubleshooting .................... 29–32

U

UL ....................................... 5, 7–11

Upgrade ...................................... 38

V

Ventilation ................................... 34

Visual Indicator ............... 20–21, 38

Voltage ........................................ 34

W

Wall Mount ............................ 13–16

Warranty ..................................... 54

White LED ......... 4, 7–11, 20–21, 38

Window ..................................... 4, 5

61

Customer Support

Technical Assistance

If you need assistance installing or troubleshooting your device, please contact

us by using one of the methods below:

Knowledge Base: www.hsmknowledgebase.com

Our Knowledge Base provides thousands of immediate solutions. If the

Knowledge Base cannot help, our Technical Support Portal (see below) provides

an easy way to report your problem or ask your question.

Technical Support Portal: www.hsmsupportportal.com

The Technical Support Portal not only allows you to report your problem, but it

also provides immediate solutions to your technical issues by searching our

Knowledge Base. With the Portal, you can submit and track your questions

online and send and receive attachments.

Web form: www.hsmcontactsupport.com

You can contact our technical support team directly by filling out our online

support form. Enter your contact details and the description of the

question/problem.

Telephone: www.honeywellaidc.com/locations

For our latest contact information, please check our website at the link above.

Product Service and Repair

Honeywell International Inc. provides service for all of its products through

service centers throughout the world. To obtain warranty or non-warranty service,

please visit www.honeywellaidc.com and select Support > Contact Service and

Repair to see your region’s instructions on how to obtain a Return Material

Authorization number (RMA #). You should do this prior to returning the product.

Honeywell Scanning & Mobility

9680 Old Bailes Road

Fort Mill, SC 29707

www.honeywellaidc.com

GEN-7580-UG Rev D

11/12