Honeywell 760006 Handheld Computer with WLAN and BT User Manual Dolphin 7600 WM6 User s Guide Rev A

Honeywell International Inc Handheld Computer with WLAN and BT Dolphin 7600 WM6 User s Guide Rev A

UserManual.wiki >

Honeywell >

760006 User Manual

User Manual

Dolphin® 7600 Mobile Computerwith Windows Mobile® 6.0User’s Guide–Preliminary

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 iiiChapter 1 - Agency ApprovalsLabel Locations....................................................................................................................1-1Approvals by Country...........................................................................................................1-2R&TTE Compliance Statement—802.11b/g and/or Bluetooth.............................................1-2Dolphin RF Terminal—802.11b/g, Bluetooth, ......................................................................1-3Chapter 2 - Getting StartedOut of the Box......................................................................................................................2-1Today Screen.......................................................................................................................2-2Navigation Bar and Start Menu............................................................................................2-2Icons in the Navigation Bar ............................................................................................2-3Command Bar......................................................................................................................2-4Selecting Programs..............................................................................................................2-5Using the Stylus ...................................................................................................................2-5Chapter 3 - Hardware OverviewStandard Configurations ......................................................................................................3-1Hardware Features ........................................................................................................3-1Peripherals...........................................................................................................................3-2Accessories..........................................................................................................................3-2Front Panel Features ...........................................................................................................3-3Touch Screen Display..........................................................................................................3-4Display Backlight............................................................................................................3-4Using Screen Protectors ................................................................................................3-4Back Panel Features..........................................................................................................3-10Using the Accessory Attachment .................................................................................3-11Side Panel Features ..........................................................................................................3-12Installing Memory Cards ..............................................................................................3-13Bottom Panel Features ......................................................................................................3-15Connecting the USB Cable ..........................................................................................3-16ActiveSync Communication ...............................................................................................3-18Battery Power ....................................................................................................................3-21Checking Battery Power...............................................................................................3-24Resetting the Terminal.......................................................................................................3-25Soft Reset (Warm Boot)...............................................................................................3-25Hard Reset (Cold Boot)................................................................................................3-25Suspend Mode...................................................................................................................3-26Chapter 4 - Using the KeyboardsOverview ..............................................................................................................................4-129-Key Numeric Keyboard.............................................................................................4-138-Key Alpha Keyboard .................................................................................................4-1Suspend/Resume...........................................................................................................4-1Function Keys ................................................................................................................4-2Modifier Keys .................................................................................................................4-2Alpha/Numeric Indicator.................................................................................................4-3Table of Contents

iv Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–Preliminary29-Key Numeric Keyboard ..................................................................................................4-4Navigation Keys.............................................................................................................4-4Hardware Application Buttons .......................................................................................4-5Toggling Between Alpha and Numeric Modes...............................................................4-629-Key Blue Key Combinations (Alpha Mode) ..............................................................4-729-Key Shift Functionality in Numeric Mode..................................................................4-729-Key Red Key Combinations......................................................................................4-838-Key Alpha Keyboard.....................................................................................................4-10Toggling Between Alpha and Numeric Modes.............................................................4-1038-Key Red Key Combinations....................................................................................4-1138-Key NUM Lock Mode .............................................................................................4-12Chapter 5 - Using the Image EngineOverview..............................................................................................................................5-1Available Engines................................................................................................................5-1Supported Bar Code Symbologies .....................................................................................5-2Activating the Engine...........................................................................................................5-3Decoding .............................................................................................................................5-3Capturing Images ................................................................................................................5-5Chapter 6 - System SettingsOverview..............................................................................................................................6-1Personal Tab .......................................................................................................................6-2Buttons...........................................................................................................................6-3Input...............................................................................................................................6-4Menus............................................................................................................................ 6-5System Tab .........................................................................................................................6-7About .............................................................................................................................6-7Backlight ........................................................................................................................6-8Certificates.....................................................................................................................6-8ClearType Tuner............................................................................................................6-8Clock & Alarms ..............................................................................................................6-9Encryption......................................................................................................................6-9Error Reporting ..............................................................................................................6-9External GPS...............................................................................................................6-10Memory........................................................................................................................6-10Power...........................................................................................................................6-12Regional Settings.........................................................................................................6-12Remove Programs.......................................................................................................6-13Screen .........................................................................................................................6-14Chapter 7 - Connecting the TerminalConnections Tab .................................................................................................................7-1Infrared Communication ......................................................................................................7-2IrDA Port Location ........................................................................................................7-2Sending Data.................................................................................................................7-2Receiving Data ..............................................................................................................7-3

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 vConnections Manager .........................................................................................................7-4Task Tab........................................................................................................................7-4Advanced Tab................................................................................................................7-5Dolphin Wireless Manager ..................................................................................................7-6Dolphin Wireless Manager Window...............................................................................7-6Enabling the Radios.......................................................................................................7-6Accessing Radio Configuration Utilities.........................................................................7-7Icons in the Navigation Bar............................................................................................7-7COM Port Assignment Table ..............................................................................................7-8Network Cards.....................................................................................................................7-9USB to PC .........................................................................................................................7-10Installing Additional Software ............................................................................................7-11Adding Programs via ActiveSync.................................................................................7-11Adding Programs From the Internet ............................................................................7-12Chapter 8 - Working with the Bluetooth RadioEnabling the Bluetooth Radio..............................................................................................8-1Icons in the Navigation Bar............................................................................................8-1Connecting to Other Bluetooth Devices ..............................................................................8-2Pairing and Trusted Devices ...............................................................................................8-4Types of Devices and Services ...........................................................................................8-5Connecting to Bluetooth Printers.........................................................................................8-6Connecting to Bluetooth Headsets......................................................................................8-6Transferring Files.................................................................................................................8-7Making the Terminal Discoverable ......................................................................................8-8Chapter 9 - Dolphin HomeBase DeviceOverview..............................................................................................................................9-1Front Panel ......................................................................................................................... 9-2Back Panel .........................................................................................................................9-3Powering the HomeBase Device.........................................................................................9-4Charging the Main Battery...................................................................................................9-5Mounting the Dolphin HomeBase Device............................................................................9-6Bottom Panel Dimensions ...................................................................................................9-7Chapter 10 - Dolphin QuadCharger DeviceOverview............................................................................................................................10-1Front Panel ....................................................................................................................... 10-1Back Panel ........................................................................................................................10-2Supplying Power to the QuadCharger Device...................................................................10-2Battery Charging................................................................................................................10-3Recommendations for Storing Batteries............................................................................10-3Mounting the QuadCharger Device...................................................................................10-4Troubleshooting.................................................................................................................10-6Chapter 11 - Dolphin Mobile MountOverview............................................................................................................................11-1Inserting a Terminal.....................................................................................................11-1Mounting............................................................................................................................11-3

vi Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryChapter 12 - Technical SpecificationsTerminal Technical Specifications.....................................................................................12-1Dolphin HomeBase Device................................................................................................12-3Dolphin QuadCharger Device............................................................................................12-5Chapter 13 - Customer SupportProduct Service and Repair...............................................................................................13-1Technical Assistance.........................................................................................................13-2Limited Warranty ...............................................................................................................13-3

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 1 - 11Agency ApprovalsLabel LocationsDolphin 7600 terminals meet or exceed the requirements of all applicable standards organizations for safe operation. However, as with any electrical equipment, the best way to ensure safe operation is to operate them according to the agency guidelines that follow. Please read these guidelines carefully before using your Dolphin terminal. Molded-in TextLaser Safety LabelIf the following label is attached to your product, it indicates the product contains a laser engine or laser aimer: Laser Eye Safety Statement: This device has been tested in accordance with and complies with IEC60825-1: 1993+A1+A2 and 21 CFR 1040.10 and 1040.11, except for deviations pursuant to Laser Notice No. 50, dated July 26, 2001. LASER LIGHT, DO NOT STARE INTO BEAM, CLASS 2 LASER PRODUCT, 1.0 mW MAX OUTPUT: 650nM. Caution - use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.LED Safety StatementThe LED output on this device has been tested in accordance with IEC60825-1 LED safety and certified to be a Class 1 LED device.FCC RF Radiation Exposure StatementThis equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. Max. SAR Measurement (1g):• 802.11b: 0.234w/kg • 802.11g: 0.234w/kgThis device has been tested and meets the FCC RF exposure guidelines for body worn operation only. An accessory must be used for body worn operation. Compliance LabelMolded-in Text (see page 1-1)hs a s i t D c Cm i tT i Cl s B D gi al evi e o pl es wi hCndiI -00 eaai muaa anCES3.Ct pprel nu eriq ed l C s e B es con e a a ormea lastform l n e00 u n aNMB- 3 dCaad .!SeeManualLASER LIGHT. DO NOT STARE INTO BEAM1.0 mW MAX OUTPUT: 650nMIEC60825-1:1993+A1+A2CLASS 2 LASER PRODUCTComplies with 21 CFR 1040.10 and 1040.1 1except for deviations pursuant to Laser Notice No. 50, dated July 26, 2001.

1 - 2 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryApprovals by Country R&TTE Compliance Statement—802.11b/g and/or BluetoothDolphin RF terminals are in conformity with all essential requirements of the R&TTE Directive (1999/5/EC). This product is marked with [Certified Notified Body Number] in accordance with the Class II product requirements specified in the R&TTE Directive. In addition, this product complies to 2006/95/EC Low Voltage Directive when supplied with the recommended power supply. Honeywell shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive.The equipment is intended for use throughout the European Community; PAN European Frequency Range: 2.402–2.480 GHz. Restrictions for use in France are as follows: • Indoor use: Maximum power (EIRP*) of 100 mW for the entire 2.400–2.4835 GHz • Outdoor use: Maximum power (EIRP*) of 100 mW for the 2.400–2.454 GHz band & maximum power (EIRP*) of 10 mW for the 2.454–2.483 MGHz band.For further information, please contact:Hand Held Products BV, a wholly owned subsidiary of Honeywell International Inc.Nijverheidsweg 95627 BT EindhovenThe NetherlandsCountry Safety EMC & RadioU.S.A. UL60950-1 (CB Scheme) FCC Part 15, Subpart C, 15.247FCC Part 15, Subpart BFCC Part 22HFCC Part 24HFCC SAR OET 65 Supplement CCanada cUL60950 ICES-003 (Class B)RSS 132RSS 133European Community/CE EN60950-1:2000EN60825-1:1994 + A11 + A2IEC60825-1EN 300328-1/2EN55022:1998+A1:2000+A2:2003EN55024:1998+A1:2001+A2:2003EN301 511EN301 489-1/-7EN301 489-17EN61000-3-2:2000EN61000-3-3:1995+A1-2001EN60360 June 2001EN50361 June 2001EN50371 June 2001

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 1 - 3Dolphin RF Terminal—802.11b/g, Bluetooth, This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet helpful: “Something About Interference.” This is available at FCC local regional offices. Our company is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by our company. The correction is the responsibility of the user. Use only shielded data cables with this system.In accordance with FCC 15.21, changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.CAUTION! Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment.Canadian ComplianceThis Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) installed outdoors is subject to licensing.Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.For European Community UsersHoneywell complies with Directive 2002/96/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003 on waste electrical and electronic equipment (WEEE).Waste Electrical and Electronic Equipment InformationThis product has required the extraction and use of natural resources for its production. It may contain hazardous substances that could impact health and the environment, if not properly disposed.In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural resources, we encourage you to use the appropriate take-back systems for product disposal. Those systems will reuse or recycle most of the materials of the product you are disposing in a sound way.

1 - 4 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryThe crossed out wheeled bin symbol informs you that the product should not be disposed of along with municipal waste and invites you to use the appropriate separate take-back systems for product disposal.If you need more information on the collection, reuse, and recycling systems, please contact your local or regional waste administration.You may also contact your supplier for more information on the environmental performances of this product.Pacemakers, Hearing Aids and Other Electrically Powered DevicesMost manufacturers of medical devices adhere to the IEC 601-1-2 standard. This standard requires devices to operate properly in an EM Field with a strength of 3V/m over a frequency range of 26 to 1000MHz. The maximum allowable field strength emitted by the Dolphin is 0.3V/m according to Subpart B of Part 1 of the FCC rules. Therefore, the Dolphin RF has no effect on medical devices that meet the IEC specification. MicrowavesThe radio in the Dolphin RF terminal operates on the same frequency band as a microwave oven. Therefore, if you use a microwave within range of the Dolphin RF terminal you may notice performance degradation in your wireless network. However, both your microwave and your wireless network will continue to function. The Dolphin Batch terminal does not contain a radio, and therefore, is not affected by microwave ovens.

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 2 - 12Getting StartedOut of the BoxVerify that your carton contains the following items: • Dolphin 7600 mobile computer (the terminal)• Main battery pack (3.7v, Li-ion)• AC power supply• Localized plug adapters •User CDNote: Be sure to keep the original packaging in case you need to return the Dolphin terminal for service; see Product Service and Repair on page 13-1. Step 1. Install the Main Battery Use only the Li-ion battery packs provided by Honeywell. Use of any battery not sold/manufactured by Honeywell may result in damage not covered by the warranty. Step 2. Charge the BatteriesUse only the peripherals, power cables, and power adapters from Honeywell. Use of peripherals, cables, or power adapters not sold/manufactured by Honeywell may cause damage not covered by the warranty.!21Dolphin terminals ship with both the main battery pack and internal backup battery significantly discharged of power. Charge the main battery pack with the charging cable for a minimum of four hours before initial use.1. Attach the appropriate plug adapter to the plug of the power cable.2. Plug the *power cable into the DC Power Jack (see page 3-12) on the left side. 3. Insert the plug into the appropriate power source. *This power cable can also be used to power the Dolphin HomeBase Device (see page 9-1).Power Cable!

2 - 2 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryStep 3. Boot the Terminal The terminal begins booting as soon as power is applied and runs by itself. Do NOT press any keys or interrupt the boot process. Only tap the screen when prompted. When the boot process is complete, the Today Screen (see page 2-2) appears and the terminal is ready for use. Today ScreenSystem resets (see Resetting the Terminal on page 3-25) complete on the Today screen. Note: You can access the Today screen any time by tapping the Start button on the Navigation bar and selecting Today in the drop-down list.Navigation Bar and Start MenuLocated at the top of every window, the Navigation bar displays various icons representing various system functions. The icons in the table below may appear in the Navigation bar. Which icons appear depend on your terminal’s configuration.Navigation BarStart Menu

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 2 - 3Icons in the Navigation BarIndicator MeaningThe terminal could not synchronize data with the workstation via ActiveSyncNew e-mail or text message (SMS)New voicemailNew instant messageRinger offVoice callVoice call in progressCalls are forwardedCall on holdMissed callData call in progressBattery levels (1–4). Tap this icon to open the Power system setting and see the charge percentage (see page 6-12).Critical battery. The charge percentage is at the critical battery point set in the registry (the default is 10%). For details about the critical battery point, (see page 3-22).Tap this icon to open the Power system setting and see the charge percentage (see page 6-12).Terminal is running on external power (If a battery pack is installed, that battery is charging.)The terminal is not connected to external power. A battery is installed but is defective; specifically, its charge level cannot be measured.No SIM card is installed GPRS availableGPRS connectedEDGE availableEDGE connected

2 - 4 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryCommand BarLocated at the bottom of the Today screen, the command bar displays running applications.RoamingRadio is disabledThe radio is not connected to a networkRadio connectedNo radio signalThe terminal is searching for a signalRadio signal strengthWi-Fi onWi-Fi data callPending alarmBluetoothIcons in the Navigation BarIndicator MeaningThis area displays various icons that access applications running on the terminal. Use the right and left arrows to navigate through these icons.

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 2 - 5Selecting ProgramsTapping Start opens the drop-down menu, which provides access to the most common system functions and programs. To open a program, tap Start > Programs. Then, tap the program icon on the menu.Using the StylusThe terminal comes with a stylus inserted into the Stylus Slot (see page 3-10), Use this stylus (or your finger) to select or enter information on the touch screen. The stylus functions as a mouse; generally, a tap is the same as a click.Tap Tap the touch screen once to open menu items and select options.Drag Hold the stylus on the screen and drag across the screen to select text and images.Tap & hold Tap and hold the stylus on an item and a pop-up menu appears. On the pop-up menu, tap the action of the task you want to perform.Use of other objects other than the stylus, such as paper clips, pencils, or ink pens can damage the touch screen and may cause damage not covered by the warranty.For more information about the touch screen, see Touch Screen Display on page 3-4.Using File ExplorerUse File Explorer to navigate through the files on your terminal. Tap Start > Programs > File Explorer. Move files by tapping and holding on the file, then tapping Cut, Copy or Paste on the pop-up menus that appear.Pop-Up MenusWith pop-up menus, you can quickly choose an action for an item. 1. Tap and hold the stylus on the item name. The pop-up menu appears.2. Lift the stylus, and tap the action you want to perform. Note: The contents of pop-up menus change according to the program you’re in.!

2 - 6 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–Preliminary

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 3 - 13Hardware OverviewStandard ConfigurationsHardware FeaturesSee•Front Panel Features on page 3-3•Back Panel Features on page 3-10•Side Panel Features on page 3-12•Bottom Panel Features on page 3-15WPAN / WLAN WPAN• Windows Mobile 6.0 Classic• Samsung 2440 400 MHz• 128MB RAM X 128 MB (non-volatile) Memory• 29-key numeric keyboard or 38-key alpha keyboard• 2.8” 1/4 VGA TFT color display• Li-ion battery: 3.7V / 3240 mAh / 12.0 Wh• 5300SR image engine• Bluetooth and 802.11b/g radios• Power cable (included in each box)• Windows Mobile 6.0 Classic• Samsung 2440 400 MHz• 128MB RAM X 128 MB (non-volatile) Memory• 29-key numeric keyboard or 38-key alpha keyboard• 2.8” 1/4 VGA TFT color display• Li-ion battery: 3.7V / 3240 mAh / 12.0 Wh• 5300SR image engine• Bluetooth radio• Power cable (included in each box)

3 - 2 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryPeripherals The following items are sold separately and enhance your terminal’s capabilities. For information about how to purchase these items, contact a Honeywell sales representative.Dolphin HomeBase™ DeviceThe Dolphin HomeBase device is a charging and communication cradle. There are two versions of this device: one that supports USB and another that supports RS-232 communication. These two options enable your terminal to interface with the majority of PC-based enterprise systems. When a terminal is seated in a powered HomeBase device, its main battery pack charges in less than four hours. For more information, see Dolphin HomeBase Device on page 9-1.Dolphin QuadCharger™ DeviceThe Dolphin QuadCharger device is a four-slot charging station for Li-ion battery packs that can charge each battery in less than four hours.For more information, see Dolphin QuadCharger Device on page 10-1. AccessoriesEach of the following items is sold separately to enhance your Dolphin terminal’s capabilities.Protective EnclosureThis enclosure wraps around the terminal to protect it from wear and tear.Li-ion Battery Packs The available Li-ion battery packs provide the main power supply for the terminal. For more information, see Battery Power on page 3-21.

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 3 - 3Front Panel FeaturesDecode and Scan LEDsThe Scan LED lights red when you press the Scan trigger in scanning applications.The Decode LED lights green when a scanned bar code is successfully decoded.Both LEDs are user-programmable.Hardware Application ButtonsThese hardware buttons appear only on the 29-key numeric keyboard and can be programmed to perform software functions available in the Buttons setting (see page 6-3). For more information about these buttons, see Hardware Application Buttons on page 4-5.KeyboardKeyboards are recessed within the housing to increase durability. There are two keyboard options available: one that defaults to numeric (shown above) and one that defaults to alpha. For information about using both keyboards, see Using the Keyboards on page 4-1.MicrophoneThe integrated microphone can be used for voice recording and communication.Decode LED Scan LED1/4 VGA Touch Screen Display (screen protector installed at the factory)Keyboard(29-key numeric)MicrophoneHardware Application Buttons

3 - 4 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryTouch Screen DisplayThe display is a 65,536-color LCD (Liquid Crystal Display) covered by a touch screen lens. The 2.8” 1/4 VGA (Video Graphic Array) is TFT (Thin Film Transistor) color, backlit, and the resolution is 240 x 320; see Display Backlight on page 3-4.Dolphin terminals ship with a screen protector already installed over the touch screen lens to help prevent damage to the touch screen. Do NOT remove this screen protector before initial use. Honeywell recommends using screen protectors, especially for applications that require high-volume interfacing with the touch screen. For more information, see Using Screen Protectors on page 3-4.For touch screen input, use the stylus included with the terminal or your finger. The method you choose depends on which one is most appropriate for your application. While there is a great deal of variation in different applications, for buttons or icons that are close together, you generally achieve greater accuracy with the stylus; see Using the Stylus on page 2-5.Use of objects, such as paper clips, pencils, or ink pens on the touch screen can damage the input panel and may cause damage not covered by the warranty. Display BacklightThe touch screen display has a backlight that is programmed to turn off after a specified period of time that the terminal is idle. For details, see Backlight on page 6-8. Using Screen Protectors Honeywell defines proper use of the terminal touch panel display as using a screen protector and proper stylus. Screen protectors maintain the ongoing integrity (i.e., prevent scratching) of the touch panel, which is why their use is recommended for applications that require a high to medium level of interface with the touch panel. Honeywell continues to advocate the use of screen protectors on all Dolphin terminals. We recommend implementing a screen protector replacement program to ensure that screen protectors are replaced periodically when signs of damage/wear are noticeable. For general use, we recommend replacing the screen protector every thirty (30) days. However, replacement cycles vary according to the average level of touch panel use in your application.Replacement screen protectors can be purchased directly from Honeywell. Please contact a Honeywell sales associate for details.Honeywell also mandates use of a proper stylus, which is one that has a stylus tip radius of no less than 0.8mm. Use of the Honeywell stylus included with the terminal is recommended at all times.Honeywell warranty policy covers wear on the touch panel display for the first 12 months provided that a screen protector is applied and an approved stylus is used for the 12 month duration covered by the warranty.Removing the Screen ProtectorDolphin terminals ship with a touch screen protector already installed. To replace the screen protector, you must remove the one already installed. !!

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 3 - 51. You will need a strong, flat, plastic card (a credit card, for example) to wedge under the existing screen protector.Note: If you have one, you can also use the small plastic squeegees designed for touch panels.2. Press the Blue + Backlight keys to put the terminal in Suspend Mode (see page 3-26).3. Carefully apply the flat edge of your plastic card to the upper right corner of the touch screen. Catch the edge of the screen protector and pull it up and away from the touch panel. Touch Panel

3 - 6 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–Preliminary4. Wipe the screen with a clean, non-abrasive, lint-free cloth.Note: Use ionized air, if available, to blow additional dirt or particles off the touch panel.Installing Your Screen ProtectorWhen installing a new screen protector, use a flat plastic card (such as a credit card) to apply the screen protector smoothly and remove any air bubbles.Note: If you have one, use the small plastic squeegees designed for touch panels.1. Press the Blue + Backlight keys to put the terminal in Suspend Mode (see page 3-26).

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 3 - 72. Clean the touch panel thoroughly with a clean, non-abrasive, lint-free cloth. Make sure nothing is attached to the top of the touch panel.3. Release the left edge of the releasing paper on the screen protector.4. Align the exposed edge of the screen protector along the left edge of the touch panel.Make sure that it lies flush with edges of the touch panel.Note: To reposition the screen protector, lift up gently and reapply.5. Use the card on top of the screen protector to it smooth out as you pull on the releasing paper.Touch Panel

3 - 8 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–Preliminary6. Pull smoothly and evenly from left to right until the screen protector is applied. Press gently but firmly. 7. Use the card as necessary to smooth out any air pockets or bumps after application. Press gently but firmly.8. Press the Backlight key to wake the terminal and check the touch panel with the stylus.9. Verify that the screen accepts input from the stylus as usual. If not, re-apply the screen protector.10. Press the Blue + Backlight keys to put the terminal back in Suspend Mode (see page 3-26).Touch Panel

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 3 - 911. Clean the surface of the screen protector with a clean, non-abrasive, lint-free cloth.12. Press the Backlight key to wake the terminal.13. For maximum performance, recalibrate the screen. Tap Start > Settings > System tab > Screen > Align Screen.14. Follow the instructions on the screen.

3 - 10 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryBack Panel FeaturesAccessory AttachmentUse this button to attach accessories; see Using the Accessory Attachment on page 3-11.Finger SaddleThis is a slightly depressed and angled area of the back panel that is designed to cradle or “saddle” your pointer finger while holding the terminal. This unique ergonomic design makes the terminal comfortable to hold and helps prevent you from accidentally dropping the terminal.Rear SpeakerThe integrated speaker sounds audio signals as you scan bar code labels and enter data but emits no ambient noise on system activity such as processor activity, memory access, radio traffic, etc. The speaker can also be used for playing sounds (e.g., WAV or MP3 files).Stylus SlotDolphin terminals ship with a stylus inserted in the back panel. Store the stylus in this slot when you’re not using it. For details, see Using the Stylus on page 2-5.Rear SpeakerStylus SlotFinger SaddleAccessory AttachmentImage Engine WindowI/O Connector

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 3 - 11Using the Accessory AttachmentThe accessory attachment is a standard tab designed to fit universal accessories available for most cell phones. An accessory must be used for body worn operation.Attaching a Belt ClipThe accessory attachment on the back panel fits universal swivel clips designed for belts or even pedestal mounts (not available from Honeywell). Simply insert the tab into the slot until you hear a click or follow the instructions that came with the clip or accessory.Attaching the Hand StrapThe accessory attachment is also how you attach the hand strap available from Honeywell. 1. Remove the accessory attachment with a Phillips head screwdriver. 2. Thread the hand strap hook underneath.3. Fasten the accessory attachment to the back panel.Keep in mind that the hand strap covers the battery. When you want to replace the battery, you will need to adjust the hand strap accordingly.

3 - 12 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminarySide Panel FeaturesNote: This graphic shows the left side of the terminal.Access DoorThis door covers the memory card slot. To increase memory, install a memory card in this slot. This terminal supports microSD™ and microSDHC™ memory cards. For details, see Installing Memory Cards on page 3-13.When closed, the access door seals the memory interface from moisture and particle intrusion thus preserving the terminal’s environmental rating. DC Power JackThe DC power jack receives external power from the power cable that comes in the box with the terminal. When connected to the power cable, the terminal is powered and the main battery pack is charging.For more information, about the power cable, see Connecting the Power Cable on page 3-17.Headset JackThis 2.5mm audio jack supports a headset with a mono speaker and microphone. IrDA PortThe IrDA (Infrared Data Association) port communicates with IrDA-enabled devices such as PCs, printers, modems, or other Dolphin terminals. Maximum data transfer speed is 115 Kbps. For more information, see Infrared Communication on page 7-2.Side ButtonThere is a button like this on both side panels. By default, these buttons wake the terminal from suspend mode unless you are in a scanning application, in which case, these buttons activate the image/scan engine. Scanning with the side buttons can be a more comfortable and therefore a more ergonomic alternative to pressing the SCAN key on the keyboard. These buttons can be programmed to launch applications from the Today screen. For more information about programming these buttons, see Customizing a Hardware Button on page 4-5.IrDA PortSide ButtonHeadset JackDC Power JackSide DoorAccess Door

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 3 - 13Side DoorThe rubber door on the left side panel provides access to the Headset and DC power jacks. When closed, the side door seals the terminal from moisture and particle intrusion thus preserving the terminal’s environmental rating. Installing Memory CardsThis terminal supports microSD and microSDHC memory cards up to 4GB. To install an SD card, you must open the access door on the side panel (Side Panel Features, page 3-12). Access door removal requires a Torx 5 (T5).1. Press the Blue + Backlight keys to put the terminal in Suspend Mode (see page 3-26).2. Place the terminal on a flat, secure surface with the keyboard face-down.3. Use a T5 screwdriver to remove the screw on the micro-SD door.4. Remove the access door.5. Slide the micro-SD card in with the contacts facing up (away from the keyboard) and the flat, straight edge parallel to the top panel (with the imager).Note: To remove an installed SD card while the access door is open, tap on the edge lightly to unlock the card; the card will pop out just enough for you to grab its edge and pull it out.Do NOT resume terminal operation while the access door is open! Operating the terminal while the access door is open may cause damage not covered by the warranty. !

$3 - 14 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–Preliminary6. Replace the access door and tighten the screw. The access door must be properly sealed before resuming terminal operation. Failure to seal the access door may cause damage not covered by the warranty.7. Press the Backlight key to resume operation.8. To verify that the operating system recognizes the new memory card, Tap Start > Programs > File Explorer and navigate to the My Device\Storage Card folder. You should see the contents of the memory card displayed on the screen.$

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 3 - 15Bottom Panel FeaturesHand Strap SlotThere is an adjustable, elastic hand strap available for purchase with the terminal. When installing the hand strap, you loop the elastic strip through this slot. For instructions, see Attaching the Hand Strap on page 3-11.I/O ConnectorThe I/O mechanical connector is designed to work exclusively with peripherals and cables designed for the Dolphin 7600 terminal. This connector powers the terminal, charges the main battery, and facilitates communication. This connector supports full speed USB 1.1 communication (up to 12 Mbps) and RS-232 communications with a maximum speed of 115Kbps and seven baud rate settings.Through this connector, you can communicate with a host workstation via Microsoft ActiveSync; see ActiveSync Communication on page 3-18.The I/O connector supports the following signals: • Data Carrier Detect• Received Data• Transmitted Data• Data Terminal Ready• Signal GND• Data Set Ready• Request To Send• Clear To Send• Ring Indicator• USB GND• USB +5V• USB D+• USB D-Note: Signals referenced are for a DTE device.I/O Connector Hand Strap Slot

3 - 16 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryConnecting the USB CableConnect the USB cable to the I/O connector to facilitate USB communication between the terminal and host workstation.*This is a communication-only cable until you plug the power cable into the power port.USB CableI/O ConnectorHost Workstation*Power Port USB Connector

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 3 - 17Connecting the Power CableThe power port on the back end of the USB connector fits the power cable that comes with each terminal. To charge the terminal while communicating, connect the power cable to the power port.Power CablePower Port

3 - 18 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryActiveSync CommunicationTo synchronize, ActiveSync 4.5 or higher must be installed and configured for the appropriate communication type on the host workstation and the Dolphin terminal. Dolphin terminals ship with ActiveSync already installed. Therefore, if ActiveSync is already installed on the host workstation, you just need to connect the Dolphin terminal to the host workstation (via Dolphin peripheral) to initiate communication.If ActiveSync 4.5 or higher is not installed on the host workstation, install it from the Getting Started CD that came with the Dolphin terminal. Insert the CD into the CD-ROM drive of the host workstation and follow the directions on your screen. You can also download the most current version of ActiveSync from www.microsoft.com and install.When communicating via ActiveSync, your terminal is designed to be connected to the host workstation with a communication peripheral sold/manufactured by Honeywell, such as the charge/communication cable. Use of any peripheral not sold/manufactured by Honeywell may cause damage not covered by the warranty.Communication TypesThe terminal supports the following types of communication via ActiveSync through its I/O Connector (see page 3-15) on the bottom panel:USB The USB cable and hardware peripherals allow the terminal to communicate with a workstation or to networked through a USB hub. The terminal supports full-speed USB communication (USB 1.1); maximum data transfer rate is 12 Mbps. The terminal defaults to USB communication out of the box.RS-232 The RS-232 cable allows the terminal to communicate with a workstation, modem, or any RS-232 device. Maximum data transfer rate is 115 Kbps.Hardware Requirements for Setup• Dolphin HomeBase device • Communication cable from Honeywell• Power cable from Honeywell; see Connecting the Power Cable on page 3-17.• USB cable (for USB communication) from Honeywell• Serial cable (for RS-232 communication) from HoneywellSoftware Requirements for CommunicationOn the workstation: • Windows 98 Second Edition, Windows Me, Windows 2000, Windows NT (4.0, SP6 or higher), Windows XP, or Windows Vista operating systems. • ActiveSync must be setup on the workstation before you initiate synchronization from the terminal for the first time.On the terminal and the workstation: • ActiveSync 4.5 or higher. ActiveSync must be configured for same communication type (USB or RS-232) on both the host workstation and the Dolphin terminal.Note: ActiveSync software is available on the Getting Started CD that comes in the box with the Dolphin terminal.!

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 3 - 19Setting Up the Host WorkstationVerify that ActiveSync is configured to use the appropriate communication type by clicking File > Connection Settings.Note: You can have both USB and RS-232 selected in the software without impacting processing. However, your hardware setup should use only RS-232 or USB, not both.Communicating with the Dolphin TerminalAfter setting up both the workstation and the terminal, ActiveSync connection should be automatic.1. Connect the Dolphin terminal to the a communication peripheral, such as the Dolphin HomeBase. 2. The Dolphin terminal automatically opens ActiveSync to establish a connection.Synchronizing with the Host WorkstationAfter setup, synchronization begins automatically whenever the terminal’s mechanical connector connects to a Dolphin peripheral that is connected to a host workstation with ActiveSync installed. Exploring the Terminal from the WorkstationWhen the terminal and workstation are connected, open the main ActiveSync window (on the desktop), and click Explore.For USB communication, check Allow USB connections.For RS-232 communication, connect to COM1.

3 - 20 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryThe Mobile Device folder opens in Windows Explorer. The terminal is now treated as a mass storage device, and transferring files is as simple as dragging and dropping or copying and pasting as you would for moving files between folders on your hard drive.

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 3 - 21Battery PowerDolphin terminals feature intelligent battery technology with two types of battery power: • The main battery pack on the back panel (see Main Battery Pack on page 3-21)• The backup battery located inside the terminal (see Internal Backup Battery on page 3-24)Both batteries work together to prevent data loss when the terminal is used over long periods of time. Both batteries must be charged to full capacity before using the terminal for the first time! Main Battery PackUse only the Li-ion battery packs provided by Honeywell. Use of any battery not sold/manufactured by Honeywell may result in damage not covered by the warranty.The Li-ion battery pack is 3.7V/3240mAh/12.0Wh and the primary power source for both the Dolphin terminal and the internal backup battery. Changing the Main Battery PackBefore installing a battery pack, press the Blue + Backlight keys to put the terminal in Suspend Mode (see page 3-26) so that operations are suspended before removing the main power source. Always put the terminal in suspend mode prior to changing the battery.Charging OptionsWhen the battery is installed in the terminal, you can insert the terminal into any one of the following peripherals:•Power Cable (see page 2-1)•Dolphin HomeBase Device (see page 9-1)• Charge/Comm Cable (see page 3-17)To fully charge the Li-ion battery before installing in the terminal, use the •Dolphin QuadCharger Device (see page 10-1)Charging TimeThe Li-ion battery pack requires four hours to charge to full capacity.Battery Pack Storage GuidelinesTo maintain optimal battery performance, follow these storage guidelines:• Avoid storing batteries outside the specified range of -4 to 122° F (-20 to 50°C) or in extremely high humidity.• For prolonged storage, do not keep batteries stored in a charger that is connected to a power source. Guidelines for Battery Pack Use and DisposalThe following are general guidelines for the safe use and disposal of batteries:• Use only the Li-ion battery packs provided by Honeywell. Use of any battery not sold/manufactured by Honeywell may pose a personal hazard to the user.!

$3 - 22 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–Preliminary• Replace defective batteries immediately; using a defective battery could damage the Dolphin terminal.• Never throw a used battery in the trash. It contains heavy metals and should be recycled according to local guidelines. • Don’t use a battery in any other manner outside its intended use in Dolphin terminals and peripherals. • Don’t short-circuit a battery or throw it into a fire; it can explode and cause severe personal injury.• Excessive discharge damages a battery. Recharge the battery when your terminal indicates low battery power.• If you observe that the battery is physically damaged in some way, please send it to Honeywell or an authorized Honeywell service center for inspection.• Although your battery can be recharged many times, it will eventually be depleted. Replace it after the battery is unable to hold an adequate charge.• If you are not sure the battery or charger is working properly, please send it to Honeywell or an authorized Honeywell service center for inspection.Managing Main Battery PowerData and files saved on the Dolphin terminal may be stored in RAM memory; therefore, maintain a continuous power supply to the terminal to help prevent data loss. When you remove a battery pack, insert another charged battery pack in the Dolphin. If the main battery pack is low, insert the terminal into a charging peripheral to power the terminal and begin recharging the battery.Note: If the main battery is low and the terminal is in suspend mode, pressing the SCAN button does not wake the Dolphin terminal; you must replace the discharged battery with a fully charged battery.Default Critical and Low Battery PointsDolphin terminals are programmed to display warnings when the battery reaches critical and low battery points. The following registry entry sets both warning points: [HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\Power] There are two DWORD values in this registry entry: LowBatt and CriticalBatt. The default values for these entries are as follows:LowBatt=19 (25%)This sets the Low Battery point to 25% (19 hex=25 decimal). When the battery hits the percentage charge specified here, the user is notified by this icon in the Navigation bar . If the main battery is low and the terminal is in suspend mode, pressing the SCAN or Power button won’t wake the Dolphin terminal; you must replace the discharged battery with a battery charged over 25% mark before you can resume terminal operation.CriticalBatt=a (10%)This sets the Critical Battery point to 10% (a hex= 0 decimal). When the battery hits the percentage charge specified here, the user is notified by this icon in the Navigation bar . Note: Warnings do not appear when the terminal is on external power.Setting Critical and Low Battery PointsDevelopers can re-reset the default battery points in the RegEdit Power Tool. 1. Tap Start > Power Tools > RegEdit.$

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 3 - 232. Drill-down to HKEY_LOCAL_MACHINE > System > CurrentControlSet > Control > Power. 3. Change the Value Data of the BattPowerOff and ExtPowerOff entries. 4. Tap OK to save changes.Note: These changes will not persist through a cold boot. To ensure that these settings persist through cold boots, you need to use the RegBackup Power Tool.For more information about Registry Power Tools, refer to the Dolphin Power Tools User’s Guide available for download at www.honeywell.com/aidc.

3 - 24 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryInternal Backup BatteryLocated inside the terminal, the backup battery is a 2.4V nickel metal hydride (NiMH) battery.The internal backup battery prevents the terminal from being reset when you remove the main battery pack. This battery retains RAM data and allows the real-time clock to remain operational for up to 30 minutes. If the terminal is left without the main battery pack for more than 30 minutes, the internal backup battery discharges and needs to be recharged to function according to specifications. Note: Even if the internal backup battery fails, data and programs stored in Flash memory (IPSM) or an optional SD card are not lost. However, the terminal automatically cold boots when you install a fully charged battery pack and you need to reset the real-time clock.ChargingThe internal backup battery charges off the main battery pack and requires eight hours charge time to backup RAM data for 30 minutes. You can begin using the Dolphin terminal after charging the main battery for four hours; however, the internal backup battery will continue to charge off the main battery. To ensure that the internal backup battery functions properly, maintain a consistent power supply for the first eight hours of terminal operation. This power supply can be external power (using a charging peripheral) or an installed, charged battery pack or a combination of both.Guidelines Follow these guidelines to maximize the life of the Dolphin’s internal backup battery:• Keep a charged Li-ion battery pack in the Dolphin terminal. • Keep the Dolphin terminal connected to a power source when the terminal is not in use. Checking Battery PowerTap Start > Settings > System tab > Power.

$Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 3 - 25Resetting the TerminalThere are two ways to reset the Dolphin terminal: a soft reset and a hard reset. Soft Reset (Warm Boot)A soft reset re-boots the terminal without losing RAM data. You would perform a soft reset 1) after installing software applications that require a reboot, 2) after making changes to certain system settings, or 3) when the terminal fails to respond.1. Press and hold Red + ESC for approximately 5 seconds. The screen turns white and the decode and scan LEDs flash for approximately three seconds. 2. When the reset is complete, the Today Screen (see page 2-2) appears.Hard Reset (Cold Boot)A hard reset erases all of the data and applications stored in RAM memory and launches AutoInstall, which re-initializes the terminal.Hard resets automatically launch a soft reset as part of the boot process.1. Press and hold Red + TAB for approximately 5 seconds. The screen turns white and the decode and scan LEDs light for approximately three seconds. 2. The terminal re-initializes, which re-installs all programs stored in the \IPSM\Autoinstall folder.Note: Set the time and date after each hard reset to ensure that the system clock is accurate. Tap the date on the Today Screen (see page 2-2) to open the Clock setting and set the time and date. !$

3 - 26 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminarySuspend Mode Suspend mode suspends terminal operation. The terminal appears to be “off” when in suspend mode. The terminal is programmed to go into suspend mode automatically when inactive for a specified period of time. You can set this time period in the Power setting.To Put the Terminal in Suspend ModePress the Blue + Backlight keys. Note: You should always put the terminal in suspend mode when you change the battery pack; see Changing the Main Battery Pack on page 3-21.To Resume Terminal OperationTo resume terminal operation (or “wake” the terminal from suspend mode), • Press the Blue + Backlight keys.• Press the Scan key .• If not in a scanning or imaging application, press one of the side buttons (see page 3-12).Troubleshooting Suspend/ResumeIf the terminal does not wake when you press the Scan key, the main battery might be too low to resume operation. To check, remove the battery and install a fully charged battery or connect the terminal to a Dolphin charging peripheral.Care and Cleaning of the Dolphin TerminalWhen needed, clean the image engine window and the LCD display with a clean, non-abrasive, lint-free cloth. The terminal can be cleaned with a damp cloth.

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 4 - 14Using the KeyboardsOverviewThere are two keyboard options: a 29-key keyboard and the 38-key keyboard. The buttons are recessed under the overlay for maximum durability and the panel is backlit for maximum viewability in various lighting conditions.Suspend/ResumeBoth keyboards provide multiple ways to suspend/resume terminal operation.29-Key Numeric Keyboard 38-Key Alpha KeyboardSuspend Blue + Backlight Resume BacklightScanF1F2 F3F4 F5 F6F7 F8 F9F10P1P2 P3P4END SENDSCANPGPG.1ESCSFT TABGHI47PQRSBKSP0STARTSP8TUVJKL52ABC9WXYZ6MNODEF3

4 - 2 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryFunction KeysFunction keys appear on both keyboards and perform specific functions.Modifier KeysModifier keys modify the next key pressed to perform functions or type special characters. For modifier key combinations on the 29-key keyboard:•See 29-Key Blue Key Combinations (Alpha Mode) on page 4-7.•See 29-Key Red Key Combinations on page 4-8.For modifier key combinations on the 38-key keyboard:•See 38-Key Red Key Combinations on page 4-11.•See 38-Key NUM Lock Mode on page 4-12.Name Key FunctionBacklight Toggles the keyboard backlight on and off.Backspace Backspace moves the cursor back one space. If you are typing text, a character is deleted each time you press the backspace key.Escape Cancels an action.Enter Performs the same function as the Enter key on a PC or workstation. Scan • Activates the image engine to scan a bar code or take an image.• Wakes the terminal from suspend mode.Tab Moves the cursor to the next tab stop or field (on a form or application window).The following keys appear only on the 29-key keyboard:Shift Provides functions as a shift key in application windows and a Caps Lock key when the 29-key keyboard is in alpha mode.On the 38-key keyboard, the Blue modifier key functions as a shift key in both alpha an numeric modes.Space Moves the cursor one space forward. If you are typing text, it moves the text one space forward as well. On the 38-key keyboard, you can perform the same function as the SP key by:• Pressing NUM + E in alpha mode• Pressing E in numeric modeName Key FunctionBlue andRed Modifies the next key pressed. The overlay of each keyboard is color-coded to indicate the character typed or function performed when the keyboard buttons are pressed in combination with these keys.

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 4 - 3Alpha/Numeric IndicatorThe Navigation bar features an icon that indicates the alpha/numeric status of the keyboard. This icon changes when the keyboard status changes. Icon Keyboard StatusThe keyboard is in lowercase alpha mode.The keyboard is in shifted (uppercase) alpha mode.The keyboard is in numeric mode.

4 - 4 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–Preliminary29-Key Numeric Keyboard Navigation KeysLocated in the center of each keyboard for easy access with either hand, the navigation keys enable you to move the cursor through application screens.Key DescriptionMove the cursor up one row or line. Volume up Page upMove the cursor down one row or line. Volume down Page downMove the cursor one character to the right. +Move the cursor one character to the left. -F1F2 F3F4 F5 F6F7 F8 F9F10P1P2 P3P4END SENDSCANPGPG.1ESCSFT TABGHI47PQRSBKSP0STARTSP8TUVJKL52ABC9WXYZ6MNODEF3BacklightModifier KeysEscapeNavigation KeysTab Shift EnterScanHardware Application ButtonsBackspace SpaceAlpha IndicatorsPGPG

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 4 - 5Hardware Application ButtonsThese four buttons are programmed to launch software applications when the Today Screen (see page 2-2) is on the screen. To customize these settings, tap Start > Settings > Personal tab > Buttons . Buttons Column Matching Hardware ButtonButtons 1–4 Buttons P1—P4 on the 29-key keyboard.Left Left side button; see Side Button on page 3-12.Right Right side button; see Side Button on page 3-12.Customizing a Hardware Button1. Select the button you want to modify. 2. Select a program from the Assign a program list. 3. Tap OK to save all changes and the change is applied immediately. 4. To verify the change, navigate to the Today screen, press the hardware button and verify that the selected application launches.P1P2 P3P4END SENDSCANHardware Application Buttons

4 - 6 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryToggling Between Alpha and Numeric ModesThe 29-key keyboard defaults to numeric mode, which means that the keyboard boots up to numeric mode after each hard reset.Numeric mode is when you type numbers with the number keys. Alpha mode is when you type letters or characters with the number keys. The keyboard switches between alpha and numeric modes easily. The command bar displays an icon that indicates the status of the keyboard so that you can see which mode you’re in when toggling; see Alpha/Numeric Indicator on page 4-3.Switching to Alpha ModeTo switch modes, tap the Blue modifier key as follows:• Single-tap to switch only the next character pressed to alpha mode. The keyboard automatically switches back to numeric mode for the next key pressed.• Double-tap to switch to alpha mode permanently. Double-tap again to switch back to numeric mode permanently.Alpha IndicatorsEach number key has a blue section with white characters inside it that indicate which letter or symbol is typed when you press that key in alpha mode. Please note that when typing in alpha mode, you must use the same multi-press method you would use when typing letters on a phone keypad. Each key press types the next letter in the sequence as displayed by the alpha indicator.Note: You can still use regular Blue key combinations in alpha mode by pressing and holding the Blue modifier key with the next key in the combination. For combinations, see 29-Key Blue Key Combinations (Alpha Mode) on page 4-7. Shift FunctionalityIn Alpha Mode When you switch the keyboard to alpha mode, letters type in lowercase by default.To capitalize letters, tap the SFT key as follows:• Single-tap to capitalize only to the next letter pressed. • Double-tap to turn CAPS LOCK on and off. In Numeric ModeNumeric mode is the default keyboard mode. When the keyboard is in numeric mode, tap the SFT key once to produce special characters; see 29-Key Shift Functionality in Numeric Mode on page 4-7.

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 4 - 729-Key Blue Key Combinations (Alpha Mode) Tap the Blue modifier key to switch to alpha mode for the next key pressed.Double-tap the Blue modifier key to switch to alpha mode permanently. FunctionsIf the keyboard is in numeric mode, tap the Blue key once to achieve the following: 29-Key Shift Functionality in Numeric ModeWhen the keyboard is in numeric mode (the default state), tap the SFT key once to produce several common characters. Key Character Uppercase: Double-tap SFT1@ ? ! : @ ? ! :2abc ABC3def DEF4ghi GHI5jkl JKL6mno MNO7pqrs PQRS8tuv TUV9wxyz WXYZKey Combination FunctionBlue + Up Arrow Volume upBlue + Down Arrow Volume downKey Character1! 2@3#4$5%6^7&8*

$4 - 8 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–Preliminary29-Key Red Key CombinationsSpecial CharactersFunctions9(0)Key Combination CharacterRed + Left Arrow -Red + Right Arrow +Red + BKSP *Red + SP #Red + . ,Red + P1 /Red + P2 =Red + P3 ;Red + P4 \Key Combination FunctionRed + ESC (hold) Soft reset (warm boot)Red + TAB (hold) Hard reset (cold boot)Red + Up Arrow Page upRed + Down Arrow Page downRed + 1 F1Red + 2 F2Red + 3 F3Red + 4 F4Red + 5 F5Red + 6 F6Red + 7 F7Red + 8 F8Key Character$

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 4 - 9Red + 9 F9Red + 0 F10Key Combination Function

4 - 10 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–Preliminary38-Key Alpha KeyboardToggling Between Alpha and Numeric ModesThe 38-key keyboard defaults to lowercase alpha mode, which means that the keyboard boots up to lowercase alpha mode after each hard reset.Numeric mode is when you type numbers with the number keys. Alpha mode is when you type letters or characters with the number keys. The keyboard switches between alpha and numeric modes easily. The command bar displays an icon that indicates the status of the keyboard so that you can see which mode you’re in when toggling; see Alpha/Numeric Indicator on page 4-3.Shift Functionality in Alpha Mode• To apply Shift functionality to the next character pressed while in lowercase alpha mode, tap the Blue modifier key once. Shift functionality is removed from the next key pressed automatically• To switch into CAPS LOCK mode, tap the Blue modifier key twice. To switch out of CAPS LOCK mode, tap the Blue modifier key twice again.Switching to Numeric Mode• To switch to numeric mode for the next key pressed, tap the NUM key once. • To lock into numeric mode, double-tap the NUM key. • If locked in numeric mode, double-tap NUM key again to switch back to alpha mode.For more information about NUM Lock functionality, see 38-Key NUM Lock Mode on page 4-12.BacklightModifier KeysEscapeNavigation KeysTab ShiftEnterScanBackspaceSpaceNUM Lock Key

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 4 - 1138-Key Red Key CombinationsKey Combination FunctionRed + ESC (hold) Soft reset (warm boot)Red + TAB (hold) Hard reset (cold boot)Red + Down Arrow P1Red + Up Arrow P2Red + Left Arrow P3Red + Right Arrow P4Red + Left Side Button P5Red + Right Side Button P6Red + A F1Red + F F2Red + K F3Red + P F4Red + U F5Red + E F6Red + J F7Red + O F8Red + T F9Red + Z F10

$4 - 12 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–Preliminary38-Key NUM Lock Mode • To switch to numeric mode for the next key pressed, tap the NUM key once. • To lock into numeric mode, double-tap the NUM key. • If locked in numeric mode, double-tap NUM key again to switch back to alpha mode.Numbers Special CharactersKey CharacterB1C2D3G4H5I6L7M8N9R0Key CharacterJ\Q.S,O/T+U@V*WXY#Z-$

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 4 - 13Special FunctionsKey CharacterAVolume upFVolume downESP

4 - 14 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–Preliminary

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 5 - 15Using the Image EngineOverviewThe Dolphin terminal houses a compact image engine using Adaptus™ Imaging Technology that instantly reads all popular 1D and 2D bar codes and supports omni-directional aiming and decoding. The image engine can also capture digital images.*Pull the plastic tab to remove the plastic film cover over the image engine window before activating the image engine.Available Engines5300 Standard Range (5300SR)*Data characterized at 23°C and 0 lux ambient light.8.3 mil Linear 10 milPDF417 13 mil UPC 15 mil Data Matrix 15 mil QR 35 milMaxiCode*Working Range:(.020cm) (.025cm) (.033cm) (.038cm) (.038cm) (.089cm)Near 3.5 in. (8.9cm) 3.1 in. (7.9cm) 2.1 in. (5.3cm) 2.3 in. 5.8cm) 3.1 in. (7.9cm) 2.0 in. (5.1cm)Far 7.6 in. (19.3cm) 9 in. (22.9cm) 13.2 in. (33.5cm) 10.2 in. (25.9cm) 8.8 in. (22.4cm) 13.0 in. (33cm)

5 - 2 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminarySupported Bar Code Symbologies Symbology Type Symbology Name1D SymbologiesCodabar Code 3 of 9Code 11Code 32 Pharmaceutical (PARAF)Code 93 Code 128 EAN with Add-OnEAN with Extended Coupon CodeEAN-8 EAN-13 GS1-128GS1 DatabarInterleaved 2 or 5 ISBT 128Matrix 2 of 5MSIPlessey PosiCode Straight 2 of 5 IATAStraight 2 of 5 IndustrialTelepen Trioptic CodeUPCUPC-AUPC-E2D Symbologies AztecCodablockCode 16KCode 49CompositeData MatrixGS1 DatabarMaxiCodeMicro PDFOCRPDF417QR Code Composite Codes Aztec MesaCodablock FEAN·UCCGS1 Databar-14OCR OCR US Money FontMICR (E 13 B) and SEMI FontOCR-A OCR-BPostal Codes Postnet and most international 4-state codes Australian PostBritish PostCanadian PostChina Post Japanese PostKIX (Netherlands) Post Korea PostPlanet Code

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 5 - 3Activating the EngineWhen a scanning application is open, press the SCAN key to activate the image engine. You can also press one of the side buttons (see page 3-12), which are programmed to activate the image engine in a scanning application by default.Using DemosDemos are software utilities loaded on all Dolphin terminals that demonstrate the advanced features of the terminal. There are two Demos feature the image engine: Image Demo and Scan Demo.To access these demos, tap Start > Demos,• Select Scan Demo to verify decoding, or• Select Image Demo to verify imaging.For more information about Demos, refer to the Dolphin Demos User’s Guide, which is available for download from www.honeywell.com/aidc.LEDsThe LEDs in the center of both keyboards (for location, see LEDs on page 4-1) light when using the image engine.Scan LED The LED on the right lights red when you press the scan trigger in scanning applications.Decode LED The LED on the left lights green when a scanned bar code is successfully decoded.DecodingThe Dolphin terminal supports two types of image decoding: full-area imaging and Advanced Linear Decoding (ALD).Full-area ImagingFull-area imaging means that the Dolphin terminal support omni-directional aiming, which means that a positive read can be obtained from many positions. For details, see Omni-Directional Scanning Positions on page 5-4. ALDALD provides fast reading of linear (1D) and stacked linear bar codes (PDF417). For the best read, the aiming pattern should be centered horizontally across the bar code. When ALD is enabled, the reader does not read matrix or postal codes.To Decode a Bar Code1. Tap Start > Demos > Scan Demo.2. Position the Dolphin terminal over one of the sample bar codes on page 5-4.A range of 4–10 inches (10–25 cm) from the bar code is recommended. 3. Project the aiming brackets by pressing and holding the SCAN key. The Scan LED lights red.4. Center the aimer crosshair over the bar code. The aiming beam should be oriented in line with the bar code to achieve optimal decoding; Omni-Directional Scanning Positions, page 5-4

5 - 4 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–Preliminary5. When the bar code is successfully decoded, the decode LED lights green and the terminal beeps.Sample Bar CodesYou can use the following bar codes to verify decoding:Omni-Directional Scanning Positions The high-vis aiming pattern frames the bar code to provide you with the best scanning performance. Note: To achieve the best read, the aiming beam should be centered horizontally across the bar code. The aiming pattern is smaller when the terminal is held closer to the code and larger when the terminal is held farther from the code. Symbologies with smaller bars or elements (mil size) should be read closer to the unit whereas larger bars or elements (mil size) should be read farther from the unit.Sample 128 Sample PDF417Code 128 PDF417 Test Message

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 5 - 5Capturing ImagesThe image-capture process is an intuitive, split-second operation for experienced users. By following basic guidelines, however, new users can easily develop their own technique and, with practice, quickly learn to adapt to different application environments.Image PreviewWhen the imaging process is initiated, the touch screen displays a preview of the object. This is a live video image of what the imager is currently viewing and has a slightly degraded appearance compared to the captured image. This is normal; the captured image has a higher resolution.File FormatsThe Dolphin terminal is capable of saving images in a number of industry-standard file formats such as BMP, JPG and PNG. The default file format for images is a grayscale JPG. File SizeDigital images have a maximum image size of 640 x 480 pixels and may have up to a 256 grayscale image definition. The image quality and related file size are determined by the data compression method used by the software application used to take the image. The average size of the image file is approximately 4–8K. However, the size of the image depends on image content, the more complex the content, the larger the file size. Taking an Image1. Tap Start > Demos > Image Demo.2. Point the terminal at the object.3. Press the SCAN key to activate the engine. The touch screen displays a preview of the object.4. Adjust the terminal’s position as necessary. Use the preview on the screen as a guide.5. Hold the terminal still and release the SCAN key. The touch screen flashes, and the captured image appears on the screen. 6. By default, the image is saved to the My Device folder. To save the image to another location, tap File > Save As.High-Vis Aiming PatternIf your terminal is configured with the 5300SR imager, you can enable the aiming pattern for imaging in the Image Demo application.1. Tap Start > Demos > Imaging Demo > Options menu > Aimer.2. The aiming pattern is now enabled for imaging.Uploading ImagesImage files can be transmitted to a host workstation via • Microsoft ActiveSync and a Dolphin communication peripheral • Wireless radio: 802.11b/g and/or Bluetooth

5 - 6 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–Preliminary

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 6 - 16System SettingsOverviewCustomized settings are available on the Start menu. Tap Start > Settings and settings screen opens displaying the Personal tab. Settings consists of three tabs: Personal, System, and Connections. Tab Description See PagePersonal Customizes buttons, set SIP options, and adjust headset settings. 6-2System Adjusts system settings. 6-7Connections Establishes network connections settings. 7-1Personal Tab System Tab Connections Tab

6 - 2 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryPersonal TabTo access the Personal tab, go to Start > Settings. The screen opens displaying the Personal tab.Note: Personal settings are stored in RAM memory. They are replaced by system defaults after each hard reset. For more information about resets, see Soft Reset (Warm Boot) on page 3-25.Icon Description For more information…Buttons Program the side buttons to perform specific tasks. See Buttons on page 6-3.Input Customizes the SIP. See Input on page 6-4.Lock Password protect the terminal to limit access to the terminal. Menus Customizes what appears on the Start menu. See Menus on page 6-5.Owner Information Enter your contact information. This information will appear on the Today screen.Sounds & Notifications Set the sound volume, enables and disables sounds for specific actions, and sets sound parameters for system notifications.Today Customize the look and the information displayed on the Today screen.

$Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 6 - 3ButtonsButtons programs both keyboard buttons and the side buttons to launch applications or execute commands. The default button assignments that appear on the Buttons window are inactive until you enable the HotKeys Power Tool.To Enable HotKeys1. Tap Start > Power Tools and tap the HotKeys icon once . HotKeys is enabled and the button assignments in the Buttons setting are active.2. Verify the assignment by tapping the button on the keyboard.For more information about the HotKeys Power Tool, refer to the Dolphin Power Tools User’s Guide, which is available for download from the web at www.honeywell.com/aidc.Button AssignmentsBy default, the side buttons (for locations, see page 3-12) activate the image engine but can be programmed to launch applications or execute commands in the Buttons setting.1. After HotKeys is enabled, tap Start > Settings > Personal tab > Buttons . Note: The buttons that appear on this window are the only buttons that can be programmed via the Buttons setting. You cannot add buttons to this window.2. To change button assignment, tap on the name of the application in the Assignment column and select a program or command in the Assign a program drop down list. 3. Tap OK to save.Available ApplicationsThe Assign a program list contains the applications installed on the terminal. If there is a program installed that you would like to see in this list, paste a Shortcut to the program in the \\Windows\Start Menu\Programs folder. For instructions about creating shortcuts, see Using File Explorer on page 6-5.$

6 - 4 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryAdditional FunctionsThe Assign a program list also contains the following commands: Input The Input settings enables you to customize input from the SIP, adjust word completion settings in Microsoft applications, and set defaults for voice recording. Command Description<Input Panel> Opens the soft input panel.<None> Nothing happens when the button is pressed. This is the default setting for the LSide and RSide buttons and means that pressing either button activates the image engine.<OK/Close> Performs the same function as tapping OK on the screen.<Scroll Down> Scrolls down in the open application.<Scroll Left> Scrolls left in the open application.<Scroll Right> Scrolls right in the open application.<Scroll Up> Scrolls up in the open application.<Start Menu> Opens the Start menu.<Today> Opens the Today screen.Input Method Options Word Completion

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 6 - 5MenusYou can add existing programs you use often, such as File Explorer, to the Start menu for faster access. You are not installing the program, just allowing access to it from the Start menu.To add programs to the Start menu, you can use • The Menus setting on the Personal tab (see page 6-5), • File Explorer (see page 6-5), or• ActiveSync (see page 6-6).Note: The Start menu can hold only seven applications at a time. Using System Settings1. Tap Start > Settings > Personal tab > Menus . 2. Tap the check box for the program you want to add and tap OK to save.Note: If you try to go over seven applications, a warning message appears and you will have to delete applications as necessary.3. Tap the Start menu to verify that the program appears on it.Using File ExplorerIf you do not see the program listed, you can either use File Explorer to move the program or ActiveSync on the workstation to create a shortcut to the program and place the shortcut in the Start Menu folder.Note: We recommend that you Copy and Paste Shortcut so that you do not alter your program configurations by accident. Using Copy and Paste Shortcut (as opposed to Cut and Paste) ensures that the program files remain where they need to be for the system to find them to perform system functions.1. Tap Start > Programs > File Explorer, and navigate to the program.File Explorer opens to My Documents by default; to see a list of all folders, tap the folder name and then My Device.

6 - 6 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–Preliminary2. Tap and hold on the program, then tap Copy on the pop-up menu. 3. Navigate to the Windows folder and open the Start Menu (My Device > Windows > Start Menu), tap and hold a blank area of the window, and tap Paste Shortcut on the pop-up menu. 4. Tap the Start menu to verify that the program now appears on it.Using ActiveSync on the WorkstationHere, you are performing the same basic process as on the terminal, except that you are using the Explore utility (Windows Explorer) to copy and paste the shortcut.1. Open ActiveSync > Explore and navigate to the program.2. Right-click on the program and select Create Shortcut. 3. Select the shortcut, right-click, and select Cut.4. Navigate to the Start Menu folder (Windows > Start Menu).5. Right-click on an empty area and select Paste Shortcut. 6. On the terminal, tap the Start menu.7. Verify that program appears.

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 6 - 7System TabThe System tab enables you to verify and sometimes alter system parameters. To access the System tab, go to Start > Settings > System tab. Tap the appropriate icon to open that system setting. For details, •See About on page 6-7.•See Backlight on page 6-8.•See Certificates on page 6-8.•See ClearType Tuner on page 6-8.•See Clock & Alarms on page 6-9.•See Encryption on page 6-9.•See Error Reporting on page 6-9.•See External GPS on page 6-10.•See Memory on page 6-10.•See Power on page 6-12.•See Regional Settings on page 6-12.•See Remove Programs on page 6-13.•See Screen on page 6-14.AboutThe About system setting displays specific information about what is loaded on the terminal. It contains three tabs:Version Tab Displays the information about the software, operating system, and processor of the terminal.Device ID Tab Displays the information the terminal uses to identify itself to other devices. It can be important to know this information if the Dolphin terminal is going to be part of a networked system of devices.Device name: Displays the system’s default name. (This is the name used by ActiveSync.)Description: Displays the description of the device ID.Copyrights Tab Displays important copyright information.

6 - 8 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryBacklightThe Backlight system setting enables you to customize backlight functionality for the display. The backlight for the color display is user-defined. Tap Start > Settings > System tab > Backlight. There are two tabs:The Battery tab determines display backlight settings when the terminal is running on battery power. The External tab determines display backlight settings when the terminal is running on external power.The options on each tab are the same. Turn off backlight: Select how many minutes you want to elapse before the backlight automatically turns off.Turn on backlight: Select this option if you want the backlight to turn on when the a button is pressed or the touch screen is tapped.Tap OK to save settings. Backlight IntensityTap the Backlight tab and move the slider to set the intensity of the backlight. The default is 8.CertificatesCertificates shows you which certificates are recognized by the operating system.If the certificate does not appear on one of these tabs, then the operating system does not recognize it and you will not be able to use that certificate.ClearType TunerThis system setting enables you to adjust the level ClearType font rendering by moving a slider. The sample text displays the setting results immediately. Of course, you must first enable ClearType font rendering to change the appearance of fonts on the screen; see ClearType Tab on page 6-14.

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 6 - 9Clock & AlarmsThis setting sets the system clock, which means that all scheduled items run according to this setting. The time and date need to be reset after every hard reset of the terminal so that the system clock is accurate.On the Today screen, tap the line that displays the time and date,The Clock Settings screen appears. The selected time sets the system clock.EncryptionEncryption gives you the option of encrypting files placed on storage cards so that those files cannot be read by any other device.Error ReportingError Reporting gives you the option of enabling or disabling the error reporting function of Windows Mobile 6.

6 - 10 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryExternal GPSIf a Windows Mobile 6.0-based device is equipped with a GPS module, External GPS is a Microsoft tool that determines which port an external GPS software application can use. The Dolphin 7600 terminal is not equipped with a GPS module.MemoryThe Memory system setting displays capacity and usage statistics for both RAM (volatile) and IPSM/Storage Card (non-volatile) memory. Access this setting whenever you receive system messages about memory.You cannot change the terminal’s memory allocation in the Memory system setting. To change the memory allocation, you need to use the SetRAM Power Tool (Start > Power Tools > SetRAM). For more details, please refer to the Honeywell Power Tools User’s Guide, which is available for download from www.honeywell.com/aidc.There are three tabs: Main, Storage Card, and Running Programs.Main Tab This tab displays the usage statistics of the on-board, volatile RAM memory. Columns: Storage=RAM memory used for storing programs and program data.Program=RAM memory used to run programs.Rows:Total= Displays the current MB of memory allocated for use.In use=Displays the total MB of that allocated memory in use.Free=Displays the total MB of memory available.

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 6 - 11Storage Card Tab This tab displays the current capacity and usage statistics of the selected memory type; IPSM or Storage Card. Select the memory type from the drop-down list. IPSM is selected by default. Total storage card memory=The total MB of memory capacity of IPSM or Storage Card.In use=The MB currently being used.Free=The MB that is still available for use. IPSM—Short for Internal Persistent Storage Manager, this is the on-board Flash memory that is non-volatile. Because this memory is non-volatile, data or programs stored in IPSM are not affected when power is removed. Autoinstall programs, for example, are stored in IPSM so that they are always installed at cold-boot startup.Storage Card—You can install one memory card in Dolphin terminals (see Access Door on page 3-12). If a storage card is installed in the terminal, you can select it in the drop-down list and see capacity and usage statistics for the card. Running Programs Tab Displays the software programs currently using Storage memory. Check this tab when you are receiving out of memory errors or when the mobile computer is running slowly. You can • Select a program in the list and tap Stop to stop it from running (and therefore from using memory), or•Tap Stop All to automatically stop all running programs.Anytime you stop a running program, it frees up RAM memory. Be advised that, when you stop a program here, any unsaved data in that program is lost. To free up memory without risking data loss, return to the running program, save your data, and close the application.!

6 - 12 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryPowerPower system settings contains three tabs: Battery and Advanced. Note: You can also set automatic turn-off times for the terminal to conserve power. When the terminal is “turned off,” that means it’s in suspend mode; see Suspend Mode on page 3-26.Regional SettingsRegional Settings enables you to customize the appearance and formatting to your geographic region. Specifically, you can customize numbers (i.e., number of decimal places allowed), currency (i.e.,using the $ or € symbol), time, and date. These specifications apply to all screens, including the Today screen. The Region tab displays an overview of the region selected in the drop-down list at the top. The terminal is loaded with a number of pre-programmed regional settings. Select one from the list and the results appear on the screen. To see specific settings or change a specific setting, tap on one of the tabs, make the change and tap OK to save it.Battery Tab Displays the remaining charge of batteries. For more information about the terminal’s batteries, see Battery Power on page 3-21.Advanced Tab Determines power time-outs.For On battery power, select from the drop-down list, the number of minutes of inactivity you want to pass before the terminal powers off when running on battery power.For On external power, select from the drop-down list, the number of minutes of inactivity you want to pass before the terminal powers off when running on external power.

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 6 - 13Remove ProgramsRemove Programs enables you to remove programs installed on the terminal. Use this setting to troubleshoot when you receive messages that the terminal is out of memory. The programs removed are removed from RAM memory. Any program (usually CAB or DLL files) stored in the Autoinstall folder (My Device > IPSM > Autoinstall) will re-install after the next hard reset. For information about the hard reset process, see Hard Reset (Cold Boot) on page 3-25.1. Tap Remove Programs. In the list, select the program you want to remove. 2. Tap Remove. The following message appears: 3. Tap Yes. Wait while the program is removed. 4. Verify that the program no longer appears in the list.

6 - 14 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryScreenThe Screen system setting contains three tabs: Alignment, Clear Type, and Text Size.Alignment Tab Orientation–The default orientation for the screen is Portrait. Select one of the Landscape options to change the screen orientation.Align Screen–You need to re-align the screen if tapping buttons or icons with the stylus no longer seems to work appropriately. Tapping Align Screen brings up the align screen window where you are guided to tap a target several times. This re-calibrates how the touch screen receives input.ClearType Tab The display supports ClearType font rendering, which is a Microsoft technology that dramatically increases the readability of text on LCD displays.To enable ClearType font rendering, select Enable ClearType and tap OK. To adjust the level of ClearType font rendering, use the ClearType Tuner; see ClearType Tuner on page 6-8.For more information about ClearType font rendering, visit: www.microsoft.com/typography/cleartype/what.htm?fname=%20&fsize=Text Size Tab The Text Size tab enables you to perform font scaling within certain views of the Today screen, Contacts, Calendar, Messaging, and Tasks. This means that you can increase or decrease the point size of the font on application windows.This is the default font size setting. To change the font size, move the slider toward Smallest or Largest. The Example text changes to reflect the font change. Tap OK to save the new font size setting.

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 7 - 17Connecting the TerminalConnections TabThe Connections system setting provides access to the terminal’s various communication options. Icon Description See PageBeam Controls whether or not the terminal can receive data via IrDA. 7-3Bluetooth Configures the Bluetooth connection.This icon appears only if a Bluetooth radio and driver is installed on the terminal. 8-1Connections Opens Microsoft’s connections manager. 7-4Dolphin Wireless Manager Manages the wireless radios installed in the terminal. 7-6Network Cards Manages the network drivers installed in the terminal. 7-9USB to PC Offers additional USB options. 7-10

7 - 2 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryInfrared CommunicationUsing the IrDA port, you can send and receive data between the terminal and other devices equipped with infrared. This can include, but is not limited to, Windows Mobile information such as Contacts and Tasks, as well as software upgrades.The maximum data transfer speed is 115 Kbps.IrDA Port Location To send or receive, the IrDA ports of both devices - whether it’s two terminals, or a terminal and a host device - must be aligned with each other and within a close range. The maximum data-transfer speed is 115 Kbps.Sending Data1. Align the IrDA ports.2. Open the program where you created the item you want to send and locate the item in the list.You can also beam files, but not folders, from File Explorer. 3. Tap and hold the item and select Beam File. 4. The IrDA port searching for a receiving IrDA port in the vicinity. The selected device reads “Pending.”IrDA Port

7 - 4 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryConnections ManagerThe connections manager sets up various network connections to Internet Service Providers (ISPs) via external modem.To open the connections manager, tap Start > Settings > Connections tab > Connections icon . Server-Assigned IP AddressesAll server-assigned IP addresses use Dynamic Host Configuration Protocol (DHCP).Zero-Config Wi-Fi The zero-config Wi-Fi feature of Windows Mobile is disabled on Dolphin 7600 terminals. If you are using one of the on-board wireless radios to connect to a network, do not enter network parameters in the connections manager. The Dolphin terminal uses the radio’s settings to connect to the network.Task TabThe Task tab enables you to initially configure, then manage network settings when using a modem. Select an item in this list and then complete the setup screens that follow with the appropriate information for your network.My ISPThe links under this heading enables you to add and manage modem connections to an ISP. To complete the setup screens, obtain the following information from your ISP:• ISP dial-up access telephone number •Username• Password • TCP/IP settingsMy Work NetworkThese links enable you to establish the following connections types:• Modem• Virtual Private Network (VPN)• Proxy server connectionTo complete the setup screens, obtain the network parameters from your system administrator.

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 7 - 5Proxy Server ConnectionsIf you are connected to your ISP or private network during synchronization, the terminal should download the proper proxy settings during synchronization with the PC. If these settings are not on your PC or need to be changed, ask your ISP or network administrator for the proxy sever name, server type, port, type of Socks protocol used, and your user name and password.Modify an Existing ConnectionManage Existing Connections appears on the Connections tab after at least one network connection has been established. Tap Manage Existing Connections on this tab and follow the setup screens. You will usually be walked through the same setup screens used to establish the connection.Advanced TabThe Advanced tab enables you to select the default network, dialing rules, and IP address exceptions for modem connections.Note: You should not need to change Advanced settings because most ISPs now use DHCP addresses.Online HelpFor more information about modem connection setup, consult the online help on the setup screens by tapping the Help icon .

7 - 6 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryDolphin Wireless ManagerThe Dolphin Wireless Manager provides a centralized interface that enables and disables all the on-board radios. Each radio has its own configuration program and the Dolphin Wireless Manager also provides shortcuts to the configuration utilities for each radio. There are two radio options: 802.11b/g and Bluetooth.1. 802.11b/g The WLAN radio is configured in the Honeywell WLAN Secure Wireless Client (SWC). Refer to the Honeywell WLAN SWC User’s Guide, which is available for download from the 7600 product page at www.honeywell.com/aidc. 2. Bluetooth See Working with the Bluetooth Radio on page 8-1.Dolphin Wireless Manager WindowTap Start > Settings > Connections tab > Dolphin Wireless Manager . Each rectangle represents a radio.Enabling the Radios1. Tap Start > Settings > Connections tab > Dolphin Wireless Manager .2. Tap anywhere inside the rectangle or the OFF button inside the rectangle. The radio begins activating.3. When the radio is activated (i.e., transmitting a signal), the OFF button changes to ON.Note: If applicable, information about the radio appears in the rectangle. If a rectangle is grayed-out, then the radio is not installed on the terminal.These buttons show you the state of the radio.

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 7 - 7Accessing Radio Configuration UtilitiesEach of the three radios have their own configuration utilities that you can access through the Menu.For 802.11b/g Tap WLAN Settings to open the SWC and configure the radio. Refer to the Honeywell WLAN SWC User’s Guide, which is available for download from the 7600 product page at www.honeywell.com/aidc.For Bluetooth Tap Bluetooth Settings to open the Bluetooth Manager and configure the radio (see page 8-1).Icons in the Navigation BarIcons that indicate radio functionality appear in the Navigation bar. For a complete listing, see Icons in the Navigation Bar on page 2-3.

7 - 8 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryCOM Port Assignment Table COM Port DescriptionCOM0 UnusedCOM1 Serial Port: RS-232 Connector on the bottom panelCOM2 Not accessibleCOM3 IrDA: Serial Infrared (SIR) up to 115 KbpsCOM4 Not accessibleCOM5 Bluetooth DUNCOM6 IrCOMMCOM7 UnusedCOM8 USB Serial: Virtual USB Serial port for ActiveSyncCOM9 Bluetooth BTHATCI server

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 7 - 9Network CardsThe Network Cards setting displays the network cards installed in the terminal.1. Tap Start > Settings > Connections > Network Cards. 2. Tap on an adapter in the list to review its settings. (Server-assigned IP addresses use DHCP.) 3. If you make a change on one of these tabs, tap OK to confirm the changes.4. You must perform a soft reset to update the registry entries; see Soft Reset (Warm Boot) on page 3-25. During the soft reset, the new registry entries are created and can be read by the applications that need them.Do NOT perform a Hard Reset (Cold Boot) (see page 3-25) after modifying an adapter here. Hard resets return the terminal to factory defaults, which erases network adapter modifications made here. !

7 - 10 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryUSB to PCThe USB to PC applet enables you to switch between RNDIS (Remote Network Driver Interface Specification) USB and Serial USB communication. Dolphin 7600 terminals default to Serial USB. Honeywell recommends using Serial USB.To change this setting, tap Start > Settings > Connections tab > USB to PC . The enable option is not selected, which indicates Serial USB.To switch to RNDIS USB, select Enable advanced network functionality and tap OK to save. (Wait as the terminal makes the change.)

Dolphin® 7600 Mobile Computer User’s Guide–Preliminary Rev (b): Preliminary9/29/2008 7 - 11Installing Additional SoftwareDolphin terminals ship with the operating system, radio drivers, and custom Honeywell software already installed. These default programs install when your terminal first boots up. You can install additional software programs to the terminal provided that the following parameters are met:• The software program was created for the Windows Mobile platform.• The terminal has enough memory to store and run the program.• The program has an EXE, CAB, or DLL extension. When selecting programs, verify that the program and version of the program are designed for the Windows Mobile 6 and the terminal’s processor. You can verify your processor by tapping Start > Settings > System tab > About > Version tab. Make a note of the information in the Processor field. To install additional software, you can use the communication options described in this chapter.•Adding Programs via ActiveSync, page 7-11.•Infrared Communication, page 7-2.Adding Programs via ActiveSyncWhen selecting programs, verify that the program and version of the program are designed for the Windows Mobile 6 and the terminal’s processor. You can verify your processor by tapping Start > Settings > System tab > About > Version tab. Make a note of the information in the Processor field. Generally, software for Windows Mobile-based devices must be installed to the host workstation first, then transferred to the terminal. 1. Download the program to the workstation from either the Internet or the install CD. You may see a single EXE or setup.exe file, a CAB file, or DLL. (There may also be several versions of files for dif-ferent device types and processors.)2. Read any installation instructions, Read Me files, or documentation that comes with the program. Many programs provide special installation instructions.3. Connect the terminal to the workstation via Honeywell communication peripheral.If the File is an InstallerAn installer program is one that installs to the workstation and the terminal simultaneously when the workstation and the terminal are connected via ActiveSync; one process installs to both devices.1. On the workstation, double-click the EXE or setup.exe file. The installation wizard begins. 2. Follow the directions on the workstation screen. The installation process includes transferring the software to the terminal via ActiveSync. !

$7 - 12 Rev (b): Preliminary9/29/2008 Dolphin® 7600 Mobile ComputerUser’s Guide–PreliminaryIf the File is Not an InstallerSome programs cannot be installed on workstations because they are designed exclusively for Windows Mobile-based devices. In these cases, the appropriate files must be stored on the host workstation and transferred to the terminal via ActiveSync Explore. Note: You know that the program is not an installer because an error message stating that the program is valid but designed for a different type of computer appears when you try to install the program on the workstation. 1. If you cannot find any installation instructions for the program in the Read Me file or documentation, open ActiveSync on the workstation and click Explore.2. On the workstation, navigate to the workstation folder containing the program file(s) and copy them to the Program Files folder on the terminal. If you want the program to persist through hard resets, past the program to the Autoinstall folder (\IPSM\AutoInstall).3. On the terminal, tap Start > Programs > File Explorer and navigate to the folder where the program is located.4. Double-tap on the program file to install it.If you copied the file to the Autoinstall folder, you can choose to install the program by performing a hard reset. The program installs as part of initialization. 5. After installation is complete, access the program by tapping Start > Programs and the program appears on the Programs screen. 6. Tap the icon to open the program.Adding Programs From the InternetWhen you have established a network connection (whether via modem or wireless radio), you can access the Internet and download additional software programs.When selecting programs, verify that the program and version of the program are designed for Windows Mobile 6 and the terminal’s processor. You can verify your processor by tapping Start > Settings > System tab > About > Version tab. Make a note of the information in the Processor field. 1. Open Internet Explorer and navigate to the program’s location. You may see a single EXE or setup.exe file, or several versions of files for different device types and processors. 2. Select the program version that matches your Dolphin terminal and processor. 3. Read any installation instructions, Read Me files, or documentation that comes with the program. Many programs provide special installation instructions.4. Download the program to the terminal straight from the Internet.You would normally store the program in the \Program Files folder unless another location is required by the program. 5. On the terminal, double-tap the installer file; e.g., the EXE file.6. The installation wizard for the program begins. 7. Follow the directions on the screen to complete installation.!$