Honeywell 7800LC Dolphin® 7800 User Manual 1 of 2

Honeywell International Inc Dolphin® 7800 1 of 2

Contents

user manual 1 of 2

DRAFT COPY 11/11/11                   Dolphin™ 7800   with Windows® Embedded Handheld 6.5   User’s Guide
DRAFT COPY 11/11/11     Disclaimer  Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII.  HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material.  This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of HII. Web Address: www.honeywellaidc.com  Trademarks  Dolphin, Dolphin RF, HomeBase, Mobile Base, ChargeBase, Net Base and QuadCharger are trademarks or registered trademarks of Hand Held Products, Inc. or Honeywell International Inc.  Microsoft, Windows, Windows Mobile, Windows Phone, Windows Embedded Handheld, Windows CE, Windows 98 Second Edition, Windows NT, Windows 2000, Windows ME, Windows XP, Windows 7, Windows Vista, ActiveSync, Outlook, and the Windows logo are trademarks or registered trademarks of Microsoft Corporation. The Bluetooth trademarks are owned by Bluetooth SIG, Inc., U.S.A. and licensed to Honeywell. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are the property of their respective owners.  Patents  For patent information, please refer to www.honeywellaidc.com/patents.    ©2011 Honeywell International Inc. All rights reserved.
DRAFT COPY 11/11/11 iii   Table of Contents     Chapter 1 - Dolphin 7800 Terminal Agency Information  Laser Safety .........................................................................................................................1-1 Label Locations ..............................................................................................................1-1 Model Number, Serial Number and IMEI Labels............................................................1-1 Laser Safety Label .........................................................................................................1-1 Laser Safety Statement..................................................................................................1-1 LED Safety ...........................................................................................................................1-2 LED Safety Statement....................................................................................................1-2 UL and C-UL Statement.......................................................................................................1-2 Approvals by Country...........................................................................................................1-2 R&TTE Compliance Statement—802.11a/b/g/n, Bluetooth, and/or GSM............................1-3 Dolphin RF Terminal—802.11a/b/g/n, Bluetooth, and/or GSM ............................................1-3 Canadian Compliance..........................................................................................................1-4 Conformité à la règlementation canadienne ........................................................................1-4 RF Exposure Information (SAR) ..........................................................................................1-4 For European Community Users .........................................................................................1-5 Waste Electrical and Electronic Equipment Information ......................................................1-5 China RoHS .........................................................................................................................1-6 Pacemakers, Hearing Aids and Other Electrically Powered Devices ..................................1-6 Hearing Aid Compatibility (HAC)..........................................................................................1-6 Microwaves ..........................................................................................................................1-7  Chapter 2 - Getting Started  Out of the Box ......................................................................................................................2-1 Initial Setup for Dolphin 7800 Terminals ..............................................................................2-1 Replacing the Main Battery Pack .........................................................................................2-4 Home Screen .......................................................................................................................2-5 Title Bar................................................................................................................................2-5 Icons in the Title Bar ............................................................................................................2-5 Horizontal Scroll ...................................................................................................................2-8 Tile Bar.................................................................................................................................2-8 Pop-Up Menus .....................................................................................................................2-8 Selecting Programs..............................................................................................................2-8 File Explorer .........................................................................................................................2-9 File Provisioning on the 7800.............................................................................................2-10 Search................................................................................................................................2-10 Resetting the Terminal .......................................................................................................2-11 Soft Reset (Warm Boot) ...............................................................................................2-11 Hard Reset (Cold Boot) ................................................................................................2-11 Factory Reset ...............................................................................................................2-11 Suspend Mode ...................................................................................................................2-11  Chapter 3 - Hardware Overview  Standard Configurations for the 7800 ..................................................................................3-1 Peripherals for the 7800.......................................................................................................3-3
DRAFT COPY 11/11/11 iv     Accessories for the 7800 ..................................................................................................... 3-4 Front Panel: 7800 ................................................................................................................ 3-5 Front Panel Features for the 7800................................................................................. 3-6 Back Panel: 7800  ............................................................................................................... 3-8 Back Panel Features for the 7800 ................................................................................. 3-9 Bottom Panel: 7800 ........................................................................................................... 3-10 I/O Connector .................................................................................................................... 3-10 Using the Touch Panel ...................................................................................................... 3-11 Installing a Screen Protector........................................................................................ 3-11 Healthcare Housing ........................................................................................................... 3-11 Batteries ............................................................................................................................ 3-12 Main Battery Pack........................................................................................................ 3-12 Internal Backup Battery ............................................................................................... 3-14 Managing Battery Power ............................................................................................. 3-14 Checking Battery Power .............................................................................................. 3-15 System Resets .................................................................................................................. 3-15 Installing a SIM Card and/or Memory Card ....................................................................... 3-16 Installation.................................................................................................................... 3-16  Chapter 4 - Using the Scan Image Engine  Overview.............................................................................................................................. 4-1 Laser Safety ........................................................................................................................ 4-1 N5603 Beam Divergence Angle .................................................................................... 4-1 LED Safety .......................................................................................................................... 4-1 Image Engine Specifications ............................................................................................... 4-1 Depth of Field ................................................................................................................ 4-1 Supported Bar Code Symbologies  ..................................................................................... 4-3 Decoding ............................................................................................................................. 4-4 To Decode a Bar Code .................................................................................................. 4-4 Aiming Beam Options .................................................................................................... 4-5 Capturing Images ................................................................................................................ 4-6 Taking an Image ............................................................................................................ 4-6 Uploading Images.......................................................................................................... 4-7  Chapter 5 - Using the Color Camera  Overview.............................................................................................................................. 5-1 Taking a picture using the Camera Demo tool .................................................................... 5-1 Taking a picture using the Windows Embedded Handheld 6.5 Camera tool ...................... 5-2 Recording Video .................................................................................................................. 5-3 Uploading Pictures and Videos...................................................................................... 5-4  Chapter 6 - Using the Keyboards  Available Keyboards ............................................................................................................ 6-1 Keyboard Combinations ................................................................................................ 6-2 Common Buttons ........................................................................................................... 6-2 Using the Function Keys...................................................................................................... 6-2 Using the Modifier Keys ...................................................................................................... 6-3
DRAFT COPY 11/11/11 v     Using the Navigation Keys .................................................................................................. 6-3 30-Key Numeric Keyboard .................................................................................................. 6-4 30-Key Numeric Keyboard Combinations...................................................................... 6-4 30-Key Numeric (Calculator) Keyboard ............................................................................... 6-6 30-Key Numeric (Calculator) Keyboard Combinations .................................................. 6-6 46-Key QWERTY Keyboard ................................................................................................ 6-8 46-Key QWERTY Keyboard Combinations ................................................................... 6-8 46-Key AZERTY Keyboard................................................................................................ 6-11 46-Key AZERTY Keyboard Combinations................................................................... 6-11 46-Key QWERTZ Keyboard .............................................................................................. 6-14 46-Key QWERTZ Keyboard Combinations ................................................................. 6-14  Chapter 7 - System Settings  Overview.............................................................................................................................. 7-1 Clock & Alarms .................................................................................................................... 7-2 Personal Menu .................................................................................................................... 7-3 Buttons........................................................................................................................... 7-3 System Menu....................................................................................................................... 7-7 About ............................................................................................................................. 7-8 Backlight ........................................................................................................................ 7-9 Battery ......................................................................................................................... 7-10 Certificates................................................................................................................... 7-10 Encryption.................................................................................................................... 7-11 Error Reporting ............................................................................................................ 7-11 External GPS ............................................................................................................... 7-11 Five Volt Control .......................................................................................................... 7-12 Smart Sensor............................................................................................................... 7-12 Managed Programs ..................................................................................................... 7-13 Memory........................................................................................................................ 7-14 RIL ............................................................................................................................... 7-15 Power........................................................................................................................... 7-15 Regional Settings......................................................................................................... 7-15 Remove Programs....................................................................................................... 7-16 Screen ............................................................................................................................... 7-17 Task Manager.................................................................................................................... 7-18  Chapter 8 - Communication  Connections Menu............................................................................................................... 8-1 Connections Manager ......................................................................................................... 8-2 To Access the Connections Manager............................................................................ 8-2 Tasks ............................................................................................................................. 8-2 Advanced....................................................................................................................... 8-3 Dolphin Wireless Manager .................................................................................................. 8-4 Dolphin Wireless Manager Window............................................................................... 8-4 Enabling the Radios....................................................................................................... 8-4 Accessing Radio Configuration Utilities ......................................................................... 8-5 Network Cards ..................................................................................................................... 8-6 Connecting and Synchronizing the Terminal and Workstation ............................................ 8-6
DRAFT COPY 11/11/11 vi     Installing Additional Software .............................................................................................. 8-8 Adding Programs Using ActiveSync or Windows Mobile Device Center ....................... 8-8 Connecting the Terminal to a Wireless Network.......................................................... 8-10 Adding Programs Using the Internet............................................................................ 8-10 Software Upgrades ............................................................................................................ 8-10 7800 COM Port Assignment Table .................................................................................... 8-11  Chapter 9 - Working with Wireless Wide Area Networking (WWAN)  Overview.............................................................................................................................. 9-1 Antenna Band ................................................................................................................ 9-1 Enabling the WWAN Radio ................................................................................................. 9-3 GSM/HSPA+ Global Radio Dolphin Models ........................................................................ 9-3 Voice Communication.................................................................................................... 9-3 Audio Modes.................................................................................................................. 9-3 Volume Control .............................................................................................................. 9-4 Accessing the Dialer Window ........................................................................................ 9-4 Dialing............................................................................................................................ 9-4 Sending Calls................................................................................................................. 9-5 Ending Calls................................................................................................................... 9-5 Accessing Voice Mail..................................................................................................... 9-5 View Options.................................................................................................................. 9-5 Setup Options ...................................................................................................................... 9-5 Data Communication (GSM/HSPA+ Global Radio Dolphin Models) ................................... 9-7 System Requirements ................................................................................................... 9-7 Information Requirements ............................................................................................. 9-7 Establishing Data Communication................................................................................. 9-7 Manual Network Selection ........................................................................................... 9-10 Data Communication GSM/CDMA Dolphin Models .......................................................... 9-11 Gobi Manager .............................................................................................................. 9-11 Establishing Data Communication............................................................................... 9-12  Chapter 10 - Working with the Bluetooth Radio  Enabling the Bluetooth Radio ............................................................................................ 10-1 Pairing and Trusted Devices ............................................................................................. 10-2 Connecting to Other Bluetooth Devices ............................................................................ 10-2 Transferring Files............................................................................................................... 10-5 Making the Terminal Discoverable .................................................................................... 10-6 Enabling the Terminal to Receive Incoming Beams .................................................... 10-6 Selecting COM Ports ......................................................................................................... 10-7  Chapter 11 - Working with GPS  Overview............................................................................................................................ 11-1 Assisted GPS Support ....................................................................................................... 11-1 Powering the GPS Module ................................................................................................ 11-1
DRAFT COPY 11/11/11 vii     Communication Ports ........................................................................................................ 11-1 Selecting the Port ........................................................................................................ 11-1 COM7 .......................................................................................................................... 11-1 GPS Intermediate Driver.............................................................................................. 11-2 GPS Demo ........................................................................................................................ 11-2  Chapter 12 - Dolphin 7800 HomeBase Device (Model 7800-HB)  Overview............................................................................................................................ 12-1 Parts and Functions........................................................................................................... 12-2 Back Panel .................................................................................................................. 12-3 Bottom Panel ............................................................................................................... 12-4 Power ................................................................................................................................ 12-4 Connecting Power to the HomeBase........................................................................... 12-4 Charging the Main Battery ................................................................................................. 12-5 To Power a Terminal and Charge its Main Battery...................................................... 12-5 Charging a Spare Battery in the Auxiliary Battery Well ............................................... 12-5 Communication.................................................................................................................. 12-6 Connecting the Communication Cables ...................................................................... 12-6 Establishing Communication ....................................................................................... 12-6 Communicating with the Dolphin Terminal .................................................................. 12-6 Mounting the HomeBase ................................................................................................... 12-7  Chapter 13 - Dolphin 7800 eBase Device (Model 7800-EHB)  Overview............................................................................................................................ 13-1 Unpacking the eBase................................................................................................... 13-1 Parts and Functions........................................................................................................... 13-2 Front Panel .................................................................................................................. 13-2 Back Panel .................................................................................................................. 13-3 Bottom Panel ............................................................................................................... 13-4 Power ................................................................................................................................ 13-4 Connecting Power to the eBase .................................................................................. 13-5 Charging the Main Battery ................................................................................................. 13-5 To Power a Terminal and Charge its Main Battery...................................................... 13-5 Charging a Spare Battery in the Auxiliary Battery Well ............................................... 13-5 Communication.................................................................................................................. 13-6 Software Requirements ............................................................................................... 13-6 Establishing Ethernet Communication......................................................................... 13-6 Establishing USB Communication ............................................................................... 13-7 Mounting the eBase........................................................................................................... 13-7 Optional Hardware Mount............................................................................................ 13-8  Chapter 14 - Dolphin 7800 Mobile Base Device (Model 7800-MB)  Overview............................................................................................................................ 14-1 Mobile Base Components  ................................................................................................ 14-2 Back Panel and Mounting Brackets................................................................................... 14-3
DRAFT COPY 11/11/11 viii     Mounting ............................................................................................................................ 14-3 Safety Precautions....................................................................................................... 14-3 Installation.................................................................................................................... 14-4 Charging the Main Battery ................................................................................................. 14-4 To Power a Terminal and Charge its Main Battery...................................................... 14-4  Chapter 15 - Dolphin 7800 ChargeBase Device (Model 7800-CB)  Overview............................................................................................................................ 15-1 Unpacking the ChargeBase......................................................................................... 15-1 Parts and Functions........................................................................................................... 15-2 Front Panel .................................................................................................................. 15-2 Back Panel................................................................................................................... 15-3 Power ................................................................................................................................ 15-3 Connecting Power to the ChargeBase  ............................................................................. 15-3 Charging the Main Battery ................................................................................................. 15-4 To Power a Terminal and Charge its Main Battery...................................................... 15-4 Mounting the ChargeBase ................................................................................................. 15-4  Chapter 16 - Dolphin 7800 Net Base Device (Model 7800-NB)  Overview............................................................................................................................ 16-1 Parts and Functions........................................................................................................... 16-2 Front Panel .................................................................................................................. 16-2 Back Panel .................................................................................................................. 16-3 Bottom Panel ............................................................................................................... 16-4 Power ................................................................................................................................ 16-4 Connecting Power to the Net Base.............................................................................. 16-4 Charging the Main Battery ................................................................................................. 16-5 To Power a Terminal and Charge its Main Battery...................................................... 16-5 Communication.................................................................................................................. 16-5 Software Requirements ............................................................................................... 16-5 Connecting the Dolphin Terminal to the Net Base ............................................................ 16-6 Mounting the Net Base ...................................................................................................... 16-6  Chapter 17 - Dolphin 7800 QuadCharger Device (Model 7800-QC)  Overview............................................................................................................................ 17-1 Parts and Functions........................................................................................................... 17-2 Power ................................................................................................................................ 17-3 Inserting and Charging Batteries ....................................................................................... 17-3 Mounting the QuadCharger ............................................................................................... 17-4 Troubleshooting ................................................................................................................. 17-5  Chapter 18 - Customer Support  Product Service and Repair............................................................................................... 18-1 Online Product Service and Repair Assistance ........................................................... 18-1 Technical Assistance ......................................................................................................... 18-2 Online Technical Assistance........................................................................................ 18-2
DRAFT COPY 11/11/11 ix     Limited Warranty ............................................................................................................... 18-3 How to Extend Your Warranty ..................................................................................... 18-4
DRAFT COPY 11/11/11 x
1 - 1       1  DRAFT COPY 11/11/11 Dolphin 7800 Terminal Agency Information     Dolphin 7800 mobile computers meet or exceed the requirements of all applicable standards organizations for safe operation. However, as with any electrical equipment, the best way to ensure safe operation is to operate them according to the agency guidelines that follow. Read these guidelines carefully before using your Dolphin terminal. This documentation is relevant for the following Dolphin models: 7800L0, 7800LW, 7800LG, 7800LC.   Laser Safety   Label Locations    7800 Back Panel         Compliance Label    Model Number, Serial Number and IMEI Labels  The model (item) number, serial number, and international mobile equipment identity (IMEI) number for the terminal are located on labels affixed to the walls of the battery well.  Laser Safety Label  If the following label is attached to your product, it indicates the product contains an engine with a laser aimer: Image Engines with Integrated Laser Aimers          Laser Safety Statement  This device has been tested in accordance with and complies with IEC60825-1(Ed. 2.0), EN60825- 1:2007. Complies with 21 CFR 1040.10 and 1040.11, except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007. LASER LIGHT, DO NOT STARE INTO BEAM. CLASS 2 LASER PRODUCT, 1.0 mW MAX OUTPUT: 650nm.  WARNING - Use of controls or adjustments or performance of procedures other than those specified herein !  may result in hazardous radiation exposure.
DRAFT COPY 11/11/11 1 - 2      LED Safety   LED Safety Statement  LEDs have been tested and classified as “EXEMPT RISK GROUP” to the Standard: IEC 62471:2006.  CAUTION! Do not view directly with optical instruments. ! UL and C-UL Statement  UL and C-UL listed: UL60950-1 2nd Edition, and CSA C22.2 No. 60950-1-07 2nd Edition.   Approvals by Country  Country EMC, Radio, & SAR Safety U.S.A. FCC Part 15, Subpart B FCC Part 15, Subpart C, 15.247 FCC Part 15, Subpart E FCC Part 22H FCC Part 24E FCC SAR OET 65 Supplement C UL60950-1 2nd Edition Canada  ICES-003 (Class B) RSS 132 RSS 133 RSS 210 CSA C22.2 No. 60950-1-07, 2nd Edition European Community/CE  EN300328, EN301893, EN55022, EN55024, EN301489-1, EN301489-7/24, EN301489-17, 3GPPTS 51.010-1, EN301511, EN301908, EN50360, EN50361, EN50371, EN50392, IEC6220-1, IEC6220-2, EN300440, 301 389-25 (CDMA 2000) EN60950-1 2nd Edition EN60825-1 2nd Edition International   IEC 60950-1 2nd Edition IEC 60825-1 2nd Edition IEC 62471   R&TTE Compliance Statement—802.11a/b/g/n, Bluetooth, and/or GSM  Dolphin RF terminals are in conformity with all essential requirements of the R&TTE Directive (1999/5/ EC).  This product is marked with   according to article 12 of the R&TTE Directive. In addition, this product complies to 2006/95/EC Low Voltage Directive when supplied with the recommended power supply. Honeywell shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive.
DRAFT COPY 11/11/11 1 - 3     The equipment is intended for use throughout the European Community; PAN European Frequency Range: 2.402–2.480 GHz. Restrictions for use in France are as follows: •   Indoor use: Maximum power (EIRP*) of 100 mW for the entire 2.400–2.4835 GHz •   Outdoor use: Maximum power (EIRP*) of 100 mW for the 2.400–2.454 GHz band & maximum power (EIRP*) of 10 mW for the 2.454–2.483 MGHz band. •   5Ghz band: UNII (Unlicensed National Information Infrastructure) or band1 (5.150 to 5.250 GHz) is restricted to indoor use only. Any other use will make the operation of the device illegal. For further information, please contact: Honeywell Imaging & Mobility Europe BV Nijverheidsweg 9 5627 BT Eindhoven The Netherlands   FCC Requirements   Dolphin RF Terminal—802.11a/b/g/n, Bluetooth, and/or GSM  This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •   Reorient or relocate the receiving antenna. •   Increase the separation between the equipment and receiver. •   Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •   Consult the dealer or an experienced radio/TV technician for help. If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet helpful: “Something About Interference.” This is available at FCC local regional offices. Our company is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by our company. The correction is the responsibility of the user. Use only shielded data cables with this system. In accordance with FCC 15.21, changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.  CAUTION! - Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.
DRAFT COPY 11/11/11 1 - 4     Canadian Compliance  This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:  (1) this device may not cause interference, and  (2) this device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES-003. This Category II radiocommunication device complies with Industry Canada Standard RSS-310.  Conformité à la règlementation canadienne  Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:  (1) l'appareil ne doit pas produire de brouillage, et  (2)  l'utilisateur  de  l'appareil  doit  accepter tout  brouillage radioélectrique subi, même  si  le  brouillage est susceptible d'en compromettre le fonctionnement." Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Ce dispositif de radiocommunication de catégorie II respecte la norme CNR-310 d’Industrie Canada.  RF Exposure Information (SAR)  This mobile phone meets the government's requirements for exposure to radio waves. This phone is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. Tests for SAR are conducted using standard operating positions accepted by the FCC with the phone transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the poser required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. The highest SAR value for the model phone as reported to the FCC when tested for use at the ear is 0.364 W/kg Max. and when worn on the body, as described in this user guide, is 0.568 W/kg Max. (Body- worn measurements differ among phone models, depending upon available accessories and FCC requirements.) While there may be differences between the SAR levels of various phones and at various positions, they all meet the government requirement. The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: HD57800LW. For body worn operation, this phone has been tested and meets the FCC RF exposure guidelines for use with an accessory that contains no metal and positions the handset a minimum of 1.5 cm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. If you do not use a body-worn accessory and are not holding the phone at the ear, position the handset a minimum of 1.5 cm from your body when the phone is switched on.
DRAFT COPY 11/11/11 1 - 5     For European Community Users  Honeywell complies with Directive 2002/96/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003 on waste electrical and electronic equipment (WEEE); European REACH Regulation 1907/2006 of 1 June, 2007, and Restriction of Hazardous Substances Directive (RoHS) 2002/95/EC of 1 July 2006.   Waste Electrical and Electronic Equipment Information  This product has required the extraction and use of natural resources for its production. It may contain hazardous substances that could impact health and the environment, if not properly disposed. In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural resources, we encourage you to use the appropriate take-back systems for product disposal. Those systems will reuse or recycle most of the materials of the product you are disposing in a sound way. The crossed out wheeled bin symbol informs you that the product should not be disposed of along with municipal waste and invites you to use the appropriate separate take-back systems for product disposal. If you need more information on the collection, reuse, and recycling systems, please contact your local or regional waste administration. You may also contact your supplier for more information on the environmental performances of this product.   China RoHS   (Names and Content of Hazardous Substances or Elements) (Toxic and Hazardous Substances or Elements) (Parts Name) (Pb) (Hg) (Cd) (Cr6+) (PBB) (PBDE) (Imager) x o o o o o (PCBA) x o o o o o (Housing) x o o o o o (Cables) o o o o o o (LCD) o o o o o o (LCD Frame) o o o o o o (Camera) x o o o o o (Keypad) o      (Battery) o o o o o o (Power Adapter) x o o o o o o:  SJ/T11363-2006 (Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in China’s SJ/T11363-2006.) x:  SJ/T11363-2006  (Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials for this part is above the limit requirement in China’s SJ/T11363-2006. )   Pacemakers, Hearing Aids and Other Electrically Powered Devices  Most manufacturers of medical devices adhere to the IEC 601-1-2 standard. This standard requires devices to operate properly in an EM Field with a strength of 3V/m over a frequency range of 26 to 1000MHz. The maximum allowable field strength emitted by the Dolphin terminal is 0.3V/m according to Subpart B of Part 1 of the FCC rules. Therefore, the RF from the Dolphin terminal has no effect on medical devices that meet the IEC specification.
DRAFT COPY 11/11/11 1 - 6     Hearing Aid Compatibility (HAC)  The Dolphin 7800 has been tested for hearing aid compatibility.  This device has an M3 and T3 rating. For additional HAC information, including the HAC rating for this product, please refer to www.honeywellaidc.com. When some wireless devices are used near some hearing devices such as hearing aids and implants, users may detect a buzzing or humming noise.  Some hearing devices are more immune than others to this interference noise.  Wireless devices may also vary in the amount of interference they generate. The ratings for compatibility of digital wireless devices with hearing aids are described in the American National Standards Institute (ANSI) C63.19 standard: M-Rating:  Phones rated M3 or M4 meet FCC requirements and are likely to generate less interference with hearing devices than phones that are not labeled.  M4 is the superior/higher of the two ratings. T-Rating:  Phones rated T3 or T4 meet FCC requirements and are likely to be more usable with hearing devices' telecoil than unrated phones.  T4 is the superior/higher of the two ratings. The more immune the hearing aid device is, the less likely one is to experience interference noise from the wireless phone.  Hearing aid devices may also be rated.  Adding the ratings of the hearing aid and the phone would determine probable usability: •   Any combined rating equal to or greater than six offers the best use. •   Any combined rating equal to five is considered normal use. The ratings are not guarantees.  Results will vary depending on the user's hearing device and hearing loss.  If your hearing device happens to be vulnerable to interference, you may not be able to use this device successfully.  Trying out this device with your hearing device is the best way to evaluate it for your personal needs. This device has been tested and rated for use with hearing aids for some of the wireless technologies that it utilizes.  However, there may be some newer wireless technologies used in this phone that have not been tested yet for use with hearing aids.  It is important to try the different features of this phone thoroughly and in different locations, using your hearing aid or cochlear implant, to determine if you hear any interfering noise.  Consult your service provider or the manufacturer of this phone for information on hearing aid compatibility.   Microwaves  The radio in the Dolphin RF terminal operates on the same frequency band as a microwave oven. Therefore, if you use a microwave within range of the Dolphin RF terminal you may notice performance degradation in your wireless network. However, both your microwave and your wireless network will continue to function.
2 - 1     2  DRAFT COPY 11/11/11 Getting Started     Out of the Box  Verify that the carton contains the following items: •   Dolphin mobile computer (the terminal) •   Main battery pack •   Quick Start Guide If you ordered accessories for your terminals, verify that they are also included with the order. Be sure to keep the original packaging in the event that the Dolphin terminal should need to be returned for service. For details, see Product Service and Repair on page 18-1.   Initial Setup for Dolphin 7800 Terminals  Step 1.  Release the Hand Strap            Step 2.  Install the Main Battery Pack  Note: Before installing the main battery pack, read the Guidelines for Battery Pack Use and Disposal on page 3-13.  Dolphin 7800 model terminals are designed for use with standard battery pack model 7800-BTSC (Li-ion 3.7 V, 8.9 watt hour) and extended battery pack models 7800-BTXC and 7800-BTXCW (Li-ion 3.7 V, 14.8 watt hour) manufactured for Honeywell International Inc. The terminal is shipped with the battery packaged separate from the unit. Perform the steps illustrated below to install the main battery. For information on how to remove the battery, see Replacing the Main Battery Pack on page 2-4.  Note: The terminal does not power ON unless the battery is locked  .  Ensure all components are dry prior to placing the battery in the terminal. Mating wet components may cause !  damage not covered by the warranty.  4 2  1  3
DRAFT COPY 11/11/11 2 - 2       Step 3.  Charge the Main and Backup Batteries  The power supply for Dolphin terminals consists of two types of battery power: the main battery pack that is accessible from the back panel, and the backup battery that resides inside the terminal.  The main battery powers the terminal. The internal backup battery charges off the main battery and maintains the application data stored in RAM memory for up to 5 minutes when the terminal’s main battery pack is completely discharged or removed. Dolphin 7800 terminals are designed for use with the following 7800 charging devices and cables: 7800-HB, 7800-EHB, 7800-NB, 7800-CB, 7800-DEX, 7800-MC, 7800-MB, 7800-USB, and 7800-USBH. See Chapters 12-17 for additional information on the individual device requirements.  Before Initial Use  Terminals are shipped with both batteries discharged of all power. The initial charging time for the main battery pack is 4 hours for the standard battery pack or 6 hours for the extended battery pack. Connect the terminal to one of the 7800 series charging peripherals to charge; see Peripherals for the 7800 on page 3-3.  Note: Honeywell recommends charging the Dolphin terminal for at least 24 hours prior to initial use to ensure the internal backup battery is fully charged.  We recommend use of Honeywell peripherals, power cables, and power adapters. Use of any non-Honeywell !  peripherals, cables, or power adapters may cause damage not covered by the warranty.  Charging Using the Communication Cable  Ensure all components are dry prior to mating terminals/batteries with peripheral devices. Mating wet !  components may cause damage not covered by the warranty.  Client Device Communication Cable (7800-USB) Use only a UL Listed power supply, which has been qualified by Honeywell with an output rated at 5VDC and 3A with the device.     3 Dolphin 7800 Models 1   Charging Cup    4  2 Power Cable
DRAFT COPY 11/11/11 2 - 3       Host Device Communication Cable (7800-USBH, 7800-DEX) Use only a UL Listed power supply, which has been qualified by Honeywell with an output rated at 5VDC and 3A with the device.    4   Plug Adapter Dolphin 7800     1  Cable Cup         Host Device    5  3 2    Power Cable USB or     COMM Cable DEX     Battery Error Notification If your terminal displays the following indicators, replace the main battery pack with a Honeywell battery pack. For information on how to remove the main battery pack from the terminal, see Replacing the Main Battery Pack on page 2-4. •   An “Authentication Error” pop up window appears during startup. •  appears in the Title bar at the top of the touch screen. •   The General Notification LED flashes red. •   A Notification appears on the Tile bar at the bottom of the touch screen.   Step 4.  Boot the Terminal  The terminal begins booting as soon as power is applied. Do NOT press any keys or interrupt the boot process. When the boot process is complete, the Home screen appears, and the terminal is ready for use.
DRAFT COPY 11/11/11 2 - 4       Step 5.  Set the Time Zone, Time, and Date  On the Home screen, tap the line that displays the time and date. When the Clock & Alarms screen appears, tap the arrow to the right of the time zone to open the drop down menu.  Select the appropiate time zone from the menu. Set the correct time and date in the remaining fields and tap OK to save.                     Replacing the Main Battery Pack  Note: Before replacing the main battery pack, read the Guidelines for Battery Pack Use and Disposal on page 3-13.  Ensure all components are dry prior to mating terminals/batteries with peripheral devices. Mating wet !  components may cause damage not covered by the warranty.  1.  Press and hold the Power key  for approximately 5 seconds to put the terminal in Suspend Mode (see page 2-11).  2.  Release the hand strap near the speaker on the back panel of the terminal.  3.  Unlock the battery by sliding the latch away from the battery.  4.  Wait at least 3 seconds, then slide the battery release button away from the stylus slot.  5.  Remove the battery.  4  5 3
DRAFT COPY 11/11/11 2 - 5         6.  Insert the new battery and apply gentle pressure to engage the latch.  Note:   Make sure the stylus tether is not caught under the battery during installation.  7.  Lock the battery by sliding the latch toward the battery pack.  Note:   The terminal does not power ON unless the battery is locked.  8.  Reattach the hand strap.  9.  Press the Power key or the SCAN key to wake the terminal from Suspend Mode (see page 2-11).  We recommend use of Honeywell Li-ion battery packs. Use of any non-Honeywell battery may result in !  damage not covered by the warranty.   Home Screen  After the Dolphin terminal initializes the first time, you see the Home screen. Tap  to reach the Start screen from the Home screen. Tap   to access the Dolphin Wireless Manager (see page 8-4) from the home screen.    Title Bar  The Title bar, located at the top of the screen, displays the active program, the status of various system functions, and the current time. Tapping on the title bar provides access to the Horizontal Scroll. The scroll provides access to additional programs and application screens. For additional information, see Horizontal Scroll on page 2-8.    Text here indicates the active program.  Icons here indicate the status of various system functions.   Icons in the Title Bar  Indicator Meaning  Synchronizing data  The terminal could not synchronize data with the workstation via ActiveSync.  New e-mail  New text message
DRAFT COPY 11/11/11 2 - 6            Icons in the Title Bar  Indicator Meaning  New voicemail  New instant message  Vibrate on  Ringer off  Speakerphone on  Voice call in progress  Calls are forwarded  Call on hold  Missed call  Data call in progress  A battery error has occurred. Replace the main battery pack with a Honeywell Li-ion battery pack.  Battery is has a full charge  Battery has a high charge  Battery has a medium charge  Battery has a low charge  Battery has a very low charge and requires charging   Terminal is running on external power. If a battery pack is installed, the battery is charging in the background.   The terminal is not connected to external power. A battery is installed, but is defective; specifically, its charge level cannot be measured.  No SIM card is installed  Active network connection  No active network connection
DRAFT COPY 11/11/11 2 - 7      Icons in the Title Bar  Indicator Meaning  GPRS available  GPRS connecting  GPRS in use  HSDPA available  HSDPA connecting  HSDPA in use  EDGE available  EDGE connecting  EDGE in use  UMTS available  UMTS connecting  UMTS in use  Radio is off  The radio is not connected to a network.  The radio is connected. The bars indicate the signal strength.  No radio signal  The terminal is searching for a signal.  Wi-Fi is on, but device is not connected  Wi-Fi data call  Pending alarm  Bluetooth
DRAFT COPY 11/11/11 2 - 8        Horizontal Scroll  The Horizontal Scroll, located at the top of most application windows, provides access to additional application screens. You can flick left or right on the scroll or tap each label on the scroll, until you get to the desired screen. Tapping a label to the left or right of the center item brings new labels into view. Note:  Tap the Title bar to access the horizontal scroll if it is not visible on the screen.   The content of the Horizontal scroll changes according to the open application.    Tile Bar  The Tile bar is located at the bottom of application windows.      The Tile bar displays icons you use to open and close screens, menues, and features. The Task tray displays icons for programs running in the background.   The icons change according to the open application.    Pop-Up Menus  With pop-up menus, you can quickly choose an action for a selected item. To access a pop-up menu, tap and hold the stylus on the item name of the action you want to perform. When the menu appears, lift the stylus, and tap the action you want to perform. Tap anywhere outside the menu to close the menu without performing an action.   Selecting Programs   To see the programs loaded on your terminal, tap  to access the Start Menu.  To open a program, tap once on the program icon. To reposition an icon on the Start Menu, tap and hold the stylus on the icon, then drag the icon to the desired position.
DRAFT COPY 11/11/11 2 - 9          File Explorer  You can also use the File Explorer to find files and organize these files into folders.   1.  Tap  > File Explorer  .                2.  Tap the Up button at the bottom of the screen to move up one level in the directory.        3.  You can move files in File Explorer by tapping and holding on the item you want to move, then tapping Cut or Copy on popup menu.  4.  Navigate to the folder you want to move the file to, then tap and hold a blank area of the window.  5.  Tap Paste on the pop-up menu.  Note: If there is no blank space available in the window, tap Menu on the command bar, navigate to the end of the menu using the down arrow, then tap Edit > Paste.
DRAFT COPY 11/11/11 2 - 10       File Provisioning on the 7800   \IPSM\Honeywell  The IPSM folder is the only partition on the 7800 that persists across a kernel upgrade (*.UPG file exten- sion). During a kernel upgrade, files are automatically copied from the \IPSM\Honeywell\Autoin- stall folder and then installed in the \Honeywell (root file system) folder as part of the upgrade process.  \IPSM\Honeywell\AutoInstall The files in the IPSM\Honeywell\AutoInstall folder are only installed when a factory reset or ker- nel upgrade occurs. Once the files are installed, they persist through hard and soft resets. If a file is added to the folder and a hard or soft reset is performed, it will have no effect. If a program is manually removed using the Remove Programs application (see page 7-16), then the program is not automatically re-installed on a hard or soft reset.   \Honeywell  The Honeywell partition or root file system partition is persistent over a Hard Reset, Soft Reset, and the removal of the battery pack or the removal of AC power. However, during a kernel upgrade the root file system is reformatted so all data in the folder is deleted and replaced by any files in the \IPSM\Honey- well\AutoInstall folder as part of the upgrade process.  !  To prevent data loss, back up all user data to an SD card or external memory device before perform- ing an upgrade.  \Honeywell\AutoInstall If you run a CAB file from within the \Honeywell\AutoInstall (user store) folder, after the program has been installed, the CAB file will be deleted from the User Store. The program remains installed through all successive Hard and Soft resets. If you want the program to be part of the Autoinstall that occurs after a factory reset or software upgrade, paste the program file(s) in both the \IPSM\Honeywell\Autoinstall folder and the \Honeywell\Autoinstall.   Contact a Honeywell technical support representative for information on how to perform a factory reset or for information on available software upgrades for your Dolphin terminal. For contact information, see Customer Support on page 18-1. or go to www.honeywellaidc.com.  !  To prevent data loss, back up all user data to an SD card or external memory device before perform- ing an upgrade.   Search    The Search feature helps you quickly locate information. Tap  > Search Phone  . Enter the text you want to find, select a data type, and then tap Search. Select Larger than 64 KB in the Type drop-down field to quickly find information that is taking up storage space.
DRAFT COPY 11/11/11 2 - 11     Resetting the Terminal  There are three types of system resets: a soft reset, a hard reset, or a factory reset. The soft and hard resets preserve all data stored in the file system. Contact a Honeywell technical support representative for more information on how to perform a factory reset.  Soft Reset (Warm Boot)  A soft reset re-boots the device and preserves any objects created in RAM. You would perform a soft reset when: the terminal fails to respond, after installing some software applications, or after making changes to certain system settings, such as network cards.  1.  Press and hold the BLUE  + END  keys for approximately 5 seconds.  2.  The general notification LED flashes orange then green for approximately 3 seconds as the terminal resets.  3.  When the reset is complete, the Home screen displays.  Hard Reset (Cold Boot)  A hard reset re-boots the device and closes any open applications running in RAM at the time of the reset.  1.  Press and hold the BLUE  + SEND  keys for approximately 5 seconds.  2.  The general notification LED flashes orange then green for approximately 3 seconds as the terminal resets.  3.  The terminal re-initializes.  Factory Reset  Contact a Honeywell technical support representative for information on how to perform a factory reset. For contact information, see Customer Support on page 18-1.   Suspend Mode  The terminal goes into Suspend Mode automatically when the terminal is inactive for a programmed period of time. You can program this time on the Advance tab of the Power System Setting; see Power on page 7-15.  To put the terminal into Suspend Mode manually, press and hold the POWER key  for approximately 5 seconds until the touch screen turns off.   To wake the terminal from Suspend Mode, press the POWER key  or SCAN key.  Note: You should always put the terminal in suspend mode before removing the battery. For information on removing the battery, see Replacing the Main Battery Pack on page 2-4.
DRAFT COPY 11/11/11 2 - 12
3 - 1   3  DRAFT COPY 11/11/11 Hardware Overview     Standard Configurations for the 7800  WLAN & WPAN •   Microsoft Windows Embedded Handheld 6.5 Classic •   800MHz TI OMAP Processor •   256MB RAM X 512MB Flash •   Six keyboard options •   3.7V Li-ion standard battery pack or extended rechargeable battery pack •   Adaptus Imaging Technology:  N5603ER/ SR/HD or N5600ER/SR/HD image engines •   802.11a/b/g/n and Bluetooth WLAN, WPAN & Camera •   Microsoft Windows Embedded Handheld 6.5 Classic •   800MHz TI OMAP Processor •   256MB RAM X 512MB Flash •   Six keyboard options •   3.7V Li-ion standard battery pack or extended rechargeable battery pack •   Adaptus Imaging Technology:  N5603ER/ SR/HD or N5600ER/SR/HD image engines •   802.11a/b/g/n and Bluetooth •   3.0 megapixel auto control color camera   WLAN, WPAN, with GPS •   Microsoft Windows Embedded Handheld 6.5 Classic •   800MHz TI OMAP Processor •   256MB RAM X 512MB Flash •   Six keyboard options •   3.7V Li-ion standard battery pack or extended rechargeable battery pack •   Adaptus Imaging Technology:  N5603ER/ SR/HD or N5600ER/SR/HD image engines •   802.11a/b/g/n and Bluetooth •   GPS WLAN, WPAN, with GPS & Camera •   Microsoft Windows Embedded Handheld 6.5 Classic •   800MHz TI OMAP Processor •   256MB RAM X 512MB Flash •   Six keyboard options •   3.7V Li-ion standard battery pack or extended rechargeable battery pack •   Adaptus Imaging Technology:  N5603ER/ SR/HD or N5600ER/SR/HD image engines •   802.11a/b/g/n and Bluetooth •   GPS •   3.0 megapixel auto control color camera   WLAN, WPAN, & WWAN •   Microsoft Windows Embedded Handheld 6.5 Professional •   800MHz TI OMAP Processor •   256MB RAM X 512MB Flash •   Six keyboard options •   3.7V Li-ion extended rechargeable battery pack •   Adaptus Imaging Technology:  N5603ER/ SR/HD or N5600ER/SR/HD image engines •   802.11a/b/g/n, Bluetooth, and GSM/ HSPA+ WLAN, WPAN, & WWAN with GPS •   Microsoft Windows Embedded Handheld 6.5 Professional •   800MHz TI OMAP Processor •   256MB RAM X 512MB Flash •   Six keyboard options •   3.7V Li-ion extended rechargeable battery pack •   Adaptus Imaging Technology:  N5603ER/ SR/HD or N5600ER/SR/HD image engines •   802.11a/b/g/n, Bluetooth, and GSM/ HSPA+ •   GPS
DRAFT COPY 11/11/11 3 - 2      WLAN, WPAN, WWAN with GPS & Camera •   Microsoft Windows Embedded Handheld 6.5 Professional •   800MHz TI OMAP Processor •   256MB RAM X 512MB Flash •   Six keyboard options •   3.7V Li-ion extended rechargeable battery pack •   Adaptus Imaging Technology:  N5603ER/ SR/HD or N5600ER/SR/HD image engines •   802.11a/b/g/n, Bluetooth, and GSM/ HSPA+ •   GPS •   3.0 megapixel auto control color camera WLAN, WPAN, & WWAN •   Microsoft Windows Embedded Handheld 6.5 Professional •   800MHz TI OMAP Processor •   256MB RAM X 512MB Flash •   Six keyboard options •   3.7V Li-ion extended rechargeable battery pack •   Adaptus Imaging Technology:  N5603ER/ SR/HD or N5600ER/SR/HD image engines •   802.11a/b/g/n, Bluetooth, and GSM/CDMA    WLAN, WPAN, & WWAN with GPS •   Microsoft Windows Embedded Handheld 6.5 Classic •   800MHz TI OMAP Processor •   256MB RAM X 512MB Flash •   Six keyboard options •   3.7V Li-ion extended rechargeable battery pack •   Adaptus Imaging Technology:  N5603ER/ SR/HD or N5600ER/SR/HD image engines •   802.11a/b/g/n, Bluetooth, and GSM/CDMA •   GPS WLAN, WPAN, WWAN with GPS & Camera •   Microsoft Windows Embedded Handheld 6.5 Classic •   800MHz TI OMAP Processor •   256MB RAM X 512MB Flash •   Six keyboard options •   3.7V Li-ion extended rechargeable battery pack •   Adaptus Imaging Technology:  N5603ER/ SR/HD or N5600ER/SR/HD image engines •   802.11a/b/g/n, Bluetooth, and GSM/ HSPA+ or GSM/CDMA •   GPS •   3.0 megapixel auto control color camera   Some configurations of the 7800 terminal are available with an external housing made of plastic that is specifically designed for the healthcare industry. For more information, see Healthcare Housing on page 3-11.
DRAFT COPY 11/11/11 3 - 3     Peripherals for the 7800  Each of the following items is sold separately to enhance the capabilities of your Dolphin terminal.   Dolphin 7800 HomeBase™ Device  The Dolphin 7800 HomeBase device is a charging and communication cradle equipped with a USB host port that is Hi-Speed 2.0v compliant, which enables the terminal to interface with the majority of PC- based enterprise systems. This device also contains an auxiliary battery well that charges a spare Hon- eywell standard or extended battery pack. For more information, see Dolphin 7800 HomeBase Device (Model 7800-HB) on page 12-1.   Dolphin 7800 Mobile Base™ Device  The Dolphin 7800 Mobile Base device is a charging and communication cradle designed specifically for in-premise and in-transit data collection applications. It features a flexible mounting bracket and a ciga- rette lighter adapter to adapt it to your environment. For more information, see Dolphin 7800 Mobile Base Device (Model 7800-MB) on page 14-1.   Dolphin 7800 eBase™ Device  The Dolphin 7800 Ethernet (eBase) device enables a single 7800 mobile computer to communicate with a host device over an Ethernet network. In addition, the ebase is equipped with a USB host port that is Hi-Speed 2.0v compliant, which enables the terminal to interface with the majority of PC-based enter- prise systems. This device also contains an auxiliary battery well that charges a spare Honeywell stan- dard or extended battery pack.  For more information, see Dolphin 7800 eBase Device (Model 7800-EHB) on page 13-1.  Dolphin 7800 Net Base™ Device  The Dolphin 7800 Net Base device enables up to four 7800 mobile computers to communicate with a host device over an Ethernet network. In addition, the Net Base provides a second RJ45 Ethernet port for connection to an additional device such as a printer, workstation, eBase, or another Net Base. For more information, see Dolphin 7800 Net Base Device (Model 7800-NB) on page 16-1.  Dolphin 7800 ChargeBase  The Dolphin 7800 ChargeBase is a 4-slot charging cradle that holds, powers, and charges terminals. For more information, see Dolphin 7800 ChargeBase Device (Model 7800-CB) on page 15-1.  Dolphin 7800 QuadCharger™ Device  The Dolphin 7800 QuadCharger device is a 4-slot charging station for Dolphin 7800 standard or extended battery packs. For more information, see Dolphin 7800 QuadCharger Device (Model 7800-QC) on page 17-1.
DRAFT COPY 11/11/11 3 - 4     Accessories for the 7800  Each of the following items is sold separately to enhance your terminal’s capabilities.  Note: When using accessories where the terminal is worn on the body, the terminal’s touch panel must face away from the body.  Dolphin 7800 Mobile Charger  The Dolphin 7800 Mobile Charger is a charging cable that connects the terminal directly to a 12 Volt DC power source, such as a cigarette lighter port inside a vehicle, eliminating the need for a cradle. Intelli- gent battery technology on-board the terminal ensures proper charging. The Dolphin 7800 Mobile Char- ger is an ideal low-cost charging solution for in-transit mobile applications.  Communication/Charging Cables  Dolphin communication/charging cable kits are an all-in-one solution for mobile applications. Each cable kit powers the terminal, charges its main battery, and communicates with host or peripheral devices with- out the need for a cradle. Cable kits can support USB client or USB host communications.  Storage Holster  The storage holster provides convenient storage for the Dolphin terminal in mobile environments. The holsters feature a belt loop to secure the holster to a belt.  Stylus Kits  Each Dolphin is shipped with a stylus and a stylus tether used to secure the stylus to the terminal to pre- vent loss. Kits containing three styli and three tethers are available for purchase.      Battery Pack  The rechargable battery pack provides the main power for the terminal. For more information, see Batteries on page 3-12.
DRAFT COPY 11/11/11 3 - 5      Front Panel: 7800    Charge Indicator LED   Front Speaker    General Notification LED         Volume Control Button Touch Panel Display     Left Scan/Image Button  Right Scan/Image Button   SCAN Key   Left Soft Key Right Soft Key   Navigation Keys    Send Call    Microphone Power Key  or  End Call      Blue Modifier Key  I/O Connector Red Modifier Key     Note: Your Dolphin model may differ from the model illustrated; however, the features noted are standard for all 7800 models unless otherwise indicated. For a complete overview of the optional keyboards available for the 7800, see Using the Keyboards on page 6-1.  For a description of each callout, see see Front Panel Features for the 7800 on page 3-6.
DRAFT COPY 11/11/11 3 - 6     Front Panel Features for the 7800  Blue Modifier Key See Using the Modifier Keys on page 6-3.  Charge Indicator LED  The light emitting diode (LED) located above the top left corner of the LCD display illuminates when the Power Tools BattMon application is enabled and the device is on AC charge. For more information, consult the Dolphin Power Tools User’s Guide for Windows Embedded Handheld 6.5.  Front Speaker The front speaker is the receiver for handset voice calls. See GSM/HSPA+ Global Radio Dolphin Models on page 9-3.  General Notification LED  The light emitting diode (LED) located above the top right corner of the LCD display flashes and illuminates during resets, scanning/imaging, and taking a picture. This LED can be programmed by various software applications.  Left Scan/Image Button  By default, the Left Button triggers the scanner/imager. You can reassign the button to launch applications or execute commands. For additional information, see Changing Button Assignments on page 7-4.  Microphone  The integrated microphone that provides audio input for handset and speakerphone voice calls. See Voice Communication on page 9-3.  Navigation Keys  The centrally located navigation keys enable you to move and position the cursor through software programs. The up and down arrows are programmed to perform specific functions when pressed in combination with the Blue and Red modifier keys. For more details, see Using the Navigation Keys on page 6-3.  Power Key  The Power key, located in the upper right corner of the keypad, puts the terminal in Suspend Mode or wakes the terminal from Suspend Mode. See Suspend Mode on page 2-11. The key is also used to end/diconnect a phone calls.  There are multiple keyboard options available for the 7800. For a complete overview of each keyboard, see Using the Keyboards on page 6-1.  Red Modifier Key See Using the Modifier Keys on page 6-3.  Right Scan/Image Button  By default, the Right Button triggers the scanner/imager. You can reassign the button to launch applications or execute commands. For additional information, see Changing Button Assignments on page 7-4.
DRAFT COPY 11/11/11 3 - 7     SCAN Key  The SCAN key is centrally located for easy access with the right or left hand. When pressed, the SCAN key activates the scanner/imager. The SCAN key also functions as a system wake- up control for the terminal.  Touch Panel Display  The color 3.7 inch 64k color liquid crystal display (LCD) touch panel is covered with an industrial, protective lens for greater durability. The video graphic array (VGA) display resolution is 480 X 640.  The touch panel backlight illuminates when the screen is touched, but not when the Backlight key is pressed. For more information, see Backlight on page 7-9.  The touch panel can be activated by the stylus (included with the terminal). For more information, see Using the Touch Panel on page 3-11.  Volume Control Button Press the top or bottom of the volume button to raise or lower the volume of the active speaker.
DRAFT COPY 11/11/11 3 - 8         Back Panel: 7800   Stylus/Stylus Slot Image/Scan Engine Window* Hand Strap Hook   Stylus Tether  Rear Speaker    Flashlight/Camera Flash    Fastener for the Stylus Tether  Color Camera         Battery Lock  Battery Release Button       Hand Strap Battery      Memory Card Socket and SIM Card Socket (located under protective shield) Battery Well   Memory/SIM Shield Screws, Qty. 2             * LED and Laser Aimer Aperture   Note: Your Dolphin model may differ from the model illustrated; however, the features noted are standard for all 7800 models unless otherwise indicated.  For a description of each callout, see Back Panel Features for the 7800 on page 3-9.
DRAFT COPY 11/11/11 3 - 9     Back Panel Features for the 7800  Battery   Dolphin 7800 model terminals are designed for use with standard battery pack model 7800- BTSC (Li-ion 3.7 V, 8.9 watt hour) and extended battery pack models 7800-BTXC and 7800- BTXCW (Li-ion 3.7 V, 14.8 watt hour) manufactured for Honeywell International Inc. For information on how to remove the battery, see Replacing the Main Battery Pack on page 2-4.  Battery Lock  The Battery Lock allows the user to lock the battery pack in place preventing battery loss due to accidental activation of the battery release. The battery release button has no effect if the Battery lock is engaged. The terminal does not power ON unless the Battery Lock is engaged.  Battery Release Button  The Battery Release Button ejects one end the battery from the terminal for easy battery removal. The battery release button has no effect if the Battery lock is engaged. For information on how to remove the battery, see Replacing the Main Battery Pack on page 2-4.  Color Camera  The 3.0-Megapixels Resolution color camera provides easy picture capture with Automated Camera Control (ACC). Additional features include automated picture profiles and an Application Programming Interface (API).  Fastener for the Stylus Tether  The Stylus Tether helps prevent accidental loss when the stylus is not stored in the stylus slot. A stylus tether is a coiled, elastic cord that tethers the stylus to the terminal.  Secure one end of the cord to the back panel of the terminal and the other end to the stylus.  Flashlight/Camera Flash The flashlight/camera flash is located on the back panel of the terminal. When used as a Flashlight, press the Red key +  key to turn the flashlight ON or OFF. When used as a Camera Flash with the terminal’s color camera, the flash is controlled by the camera application.  Hand Strap  The 7800 comes with an elastic hand strap. One end of the hand strap can be released to provide easy access to the battery pack. The hand strap release hook is located near the speaker on the back panel of the terminal.  Image/Scan Engine Window  The available image engines read and decode linear, stacked linear (e.g., PDF417), and 2D matrix bar code symbologies. Some of the available engine models contain a laser aimer for greater accuracy. The laser apertures for the imaging engines’ laser aimers are contained behind this window. For more details, see Using the Scan Image Engine on page 4-1.  Memory Card Socket and SIM Card Socket  The memory card socket provides the user with the option to expand the terminal’s memory capacity using industry-standard microSD or microSDHC memory interfaces. The expansion socket is located under the main battery in the battery well. The card socket for the Subscriber Identity Module (SIM) is also located under the main battery in the battery well.
DRAFT COPY 11/11/11 3 - 10      When the protective SIM/memory card cover and battery pack are properly installed, the cards are sealed against moisture and particle intrusion, read/write data is stored securely, and the terminal’s environmental rating is preserved; see Installing a SIM Card and/or Memory Card on page 3-16.  Rear Speaker  The integrated rear speaker sounds audio signals as you scan bar code labels and enter data. The integrated speaker also supports playback of wave and MP3 files, software mixer, and Speakerphone for WWAN/GSM audio.  The operating frequency range is 600-3000Hz at >90dB.  Stylus/Stylus Slot  The stylus is used to operate the touch panel. The back panel of the terminal features a storage slot to hold the stylus when not in use. The stylus features a special tip for added accuracy and ease of use.      Bottom Panel: 7800  Pin Description 1 PWR 2 PWR 3 USB1 HOST D- 4 USB1 HOST 5V OUT 5 USB1 HOST D+ 6 A_GND 7 USB Client D+ 8 USB Client VBUS 9 USB Client D- 10 GND 11 GND  Note: Signals referenced are for a DTE device.  I/O Connector  The I/O connector powers the terminal, charges the main battery, and facilitates communication. All Dol- phin peripherals are designed to work exclusively with this connector. The I/O connector supports high speed USB v2.0 communication with a maximum rate of 480 Mbps.
DRAFT COPY 11/11/11 3 - 11     I/O Power Out  The I/O connector also provides power out (to peripheral devices) +5V at 500mA. This means that, with the proper cable, the terminal can power another device. By default, power out is disabled, but the 5V output may be enabled, see Five Volt Control on page 7-12.   Using the Touch Panel  Honeywell defines proper use of the terminal touch panel as using a screen protector and proper stylus. Screen protectors maintain the ongoing integrity (i.e., prevent scratching) of the touch panel, which is why their use is recommended for applications that require a high to medium level of interface with the touch panel, such as signature capture for proof of delivery. Honeywell advocates the use of screen protectors on all Dolphin devices. We recommend implementing a screen protector replacement program to ensure that screen protectors are replaced periodically when signs of damage/wear are noticeable. Replacement screen protectors can be purchased directly from Honeywell. Please contact a Honeywell sales associate for details. Honeywell also mandates use of a proper stylus, which is one that has a stylus tip radius of no less than 0.8 mm. Use of the Honeywell stylus included with the terminal is recommended at all times. Honeywell warranty policy covers wear on the touch panel for the first twelve (12) months if a screen pro- tector is applied and an approved stylus is used for the 12 month duration covered by the warranty.  Installing a Screen Protector  Dolphin terminals ship with a screen protector already installed. You will need to replace the screen pro- tector at regular intervals.  1.  After the current screen protector has been removed from the touch panel, clean the touch panel thoroughly with a clean, non-abrasive, lint-free cloth. Make sure there is no debris on the touch panel.  2.  Align the exposed section of the protector with the edge of the touch panel. Make sure that the screen protector is flush with edges of the touch panel. To reposition, lift up gently and reapply.  3.  Press the screen protector firmly and carefully across the surface of the touch panel as you peel away the backing.  4.  If necessary, smooth out any air pockets or bumps.  Healthcare Housing  Some configurations of the 7800 terminal are available with an external plastic housing that is designed to resist the effects of harsh chemicals in a healthcare environment. The plastic is crystalline in nature, which helps prevent chemicals from seeping through the housing.  Important!  The following cleaning solutions have been tested to assure safe cleaning of your terminal’s disinfectant-ready housing. They are the only solutions approved for use with these terminals. Damage caused by the use of cleaners other than those listed below may not be covered by the warranty. •   Sani-Cloth® Plus wipes •   Gentle dish soap and water
DRAFT COPY 11/11/11 3 - 12     Batteries  There are two types of battery power: the main battery pack installed in the back panel and the backup battery located inside the terminal. They are designed to work together to prevent data loss when the terminal is in use over long periods. Both batteries must be completely charged before using a Dolphin terminal for the first time!  Main Battery Pack  We recommend use of Honeywell Li-ion battery packs. Use of any non-Honeywell battery may result in !  damage not covered by the warranty. Dolphin 7800 model terminals are designed for use with standard battery pack model 7800-BTSC (Li-ion 3.7 V, 8.9 watt hour) and extended battery pack models 7800-BTXC and 7800-BTXCW (Li-ion 3.7 V, 14.8 watt hour) mhanufactured for Honeywell International Inc.  Charging Options  When the main battery pack is installed in the terminal, use one of the following peripherals: •   Dolphin 7800 HomeBase Device (Model 7800-HB) (see page 12-1) •   Dolphin 7800 eBase Device (Model 7800-EHB) (see page 13-1) •   Dolphin 7800 Mobile Base Device (Model 7800-MB) (see page 14-1) •   Dolphin 7800 ChargeBase Device (Model 7800-CB) (see page 15-1) •   Dolphin 7800 Net Base Device (Model 7800-NB) (see page 16-1) When the main battery pack is not installed in the terminal: •   Place the battery pack in the Dolphin 7800 QuadCharger Device (Model 7800-QC) (see page 17-1) •   Place the battery pack in the Auxiliary Battery Well of the Dolphin 7800 HomeBase Device (Model 7800-HB) (see page 12-1) or Dolphin 7800 eBase Device (Model 7800-EHB) (see page 13-1).   For information on how to remove the main battery pack from the terminal, see Replacing the Main Battery Pack on page 2-4.  Charging Time  The standard battery pack requires 4 hours to charge completely before initial and the extended battery pack requires 6 hours to charge completely before initial use. Honeywell recommends charging the Dolphin terminal for at least 24 hours prior to initial use to ensure the internal backup battery is fully charged.  Battery Error Notification  If your terminal displays the following indicators, replace the main battery pack with a Honeywell Li-ion 7800 standard or extended battery pack. For information on how to remove the main battery pack from the terminal, see Replacing the Main Battery Pack on page 2-4.  •  appears in the Title bar at the top of the touch screen. •   The General Notification LED flashes red. •   A Notification appears on the Tile bar at the bottom of the touch screen.
DRAFT COPY 11/11/11 3 - 13     Storing Batteries  To maintain top performance from batteries, avoid storing batteries outside of the following temperature ranges: •   14°F to 113°F (-10°C to +45°C) for short term storage of less than one month •   32°F to 86°F (-0°C to +30°C) for long term storage Do not store batteries in extremely high humidity. For prolonged storage, do not keep batteries stored in a charger that is connected to a power source.  Guidelines for Battery Pack Use and Disposal  The following are general guidelines for the safe use and disposal of batteries: •   Do not disassemble or open crush, bend or deform, puncture or shred. •   Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, expose to fire, explosion or other hazard. •   Improper battery use may result in a fire, explosion or other hazard. •   We recommend use of Honeywell Li-ion battery packs. Use of any non-Honeywell battery may pose a personal hazard to the user. •   Only use the battery for the system for which it is specified. Do not use a battery in any other manner outside its intended use in Dolphin terminals and peripherals. •   Only use the battery with a charging system that has been qualified with the system per standard IEEE- Std-1725-2006. Use of an unqualified battery or charger may present a risk of fire, explosion, leakage, or other hazard. •   Replace the battery only with another battery that has been qualified with the system per this standard, IEEE-Std-1725-2006. Use of an unqualified battery may present a risk of fire, explosion, leakage or other hazard. •   Replace defective batteries immediately; using a defective battery could damage the Dolphin terminal. •   Never throw a used battery in the trash. Promptly dispose of used batteries in accordance with local regulations. •   Do not short-circuit a battery or throw it into a fire; it can explode and cause severe personal injury. Do not allow metallic conductive objects to contact battery terminals. •   If you observe that the Honeywell battery supplied is physically damaged, please send it to Honeywell International Inc. or an authorized service center for inspection, see Product Service and Repair on page 18-1. •   Avoid dropping the terminal or battery. If the terminal or battery is dropped, especially on a hard surface, and the user suspects damage, send it to a Honeywell International Inc. or an authorized service center for inspection. •   If you are not sure the battery or charger is working properly, send it to Honeywell International Inc. or an authorized service center for inspection, see Product Service and Repair on page 18-1. •   Excessive discharge can degrade battery performance. Recharge the battery when your terminal indicates low battery power. •   Although your battery can be recharged many times, the battery life is limited. Replace it after the battery is unable to hold an adequate charge.
DRAFT COPY 11/11/11 3 - 14     Internal Backup Battery  Located inside the terminal is a 3.6 Volt nickel metal hydride (NiMH) backup battery.  The backup battery prevents the terminal from being reset if you need to replace the main battery pack. It retains RAM data during the battery pack exchange. A fully charged backup battery provides 5 minutes of data backup time.  Note: A fully charged backup battery preserves RTC content for approximately 168 hours when the terminal is in suspend mode and the main battery is not installed or completely depleted of charge.  If at any time the backup battery becomes fully discharged of power (e.g., the terminal is left without the main battery pack for more than 5 minutes), the terminal resets when power is supplied. All files are retained, but you may need to restart any running applications. In addition, a fully discharged backup battery requires a minimum of 24 hours of charging time to reach a full charge. Note: Data and programs stored in Flash memory are not lost even if the internal backup battery fails.  Charging  The internal backup battery is powered by the main battery pack. Therefore, charging the internal battery requires a charged main battery pack be installed in the terminal and the terminal be connected to a charging device. The internal backup battery must be fully charged before using the terminal for the first time. Honeywell recommends charging the Dolphin terminal for at least 24 hours prior to initial use to ensure the internal backup battery is fully charged. After that, if the internal backup battery becomes fully discharged of power, it requires a minimum of 24 hours of charging time to function normally.  Guidelines for Use  Follow these guidelines to maximize the life of the internal backup battery:  •   Keep a charged battery pack in the terminal; the backup battery prematurely discharges if there is not at least a partially charged battery in the terminal. •   Keep the terminal connected to power when the terminal is not in use.  Managing Battery Power  Letting the backup battery become fully discharged causes the terminal to lose all data in RAM. Honey- well recommends, you keep a charged battery pack in the terminal at all times to help prevent data loss. The internal battery discharges prematurely if there is not at least a partially charged battery in the termi- nal. When you remove a battery pack, insert another charged battery pack in the terminal immediately.  Default Critical and Low Battery Points  When the terminal is running on battery power (as opposed to external power), warnings are displayed when the battery reaches critical and low battery points. The warning points are determined by the fol- lowing registry entry: [HKEY_LOCAL_MACHINE\ControlPanel\Power] There are two DWORD values in this registry entry: MedState and LowState. The default values for these entries are as follows:
DRAFT COPY 11/11/11 3 - 15     MedState=25%  This sets the Low Battery point to 25%. When the battery hits the percentage charge specified here, the user is notified.  LowState=10%  This sets the Critical Battery point to 10%. When the battery hits the percentage charge specified here, the user is notified.  Note: Warnings do not appear when the terminal is on external power.  Setting Critical and Low Battery Points  Developers can reset the battery parameters in the registry from 0 (no warning) to 99 (would nearly always warn). You can review and set these battery points in the RegEdit Power Tool.   1.  Tap  > Power Tools > RegEdit.  2.  Drill down to HKEY_LOCAL_MACHINE > ControlPanel > Power.  3.  Tap the Value Name to change the Value Data. You can reset the Value Data from 0 (no warning) to 99 (would nearly always warn).  4.  Tap OK to save changes.  For more information about the RegEdit Power Tool, refer to the Dolphin Power Tools User’s Guide avail- able for download at www.honeywellaidc.com.  Checking Battery Power   1.  Tap  > Settings > System  2.  Tap Power to view the power status of the main battery and backup battery.  Note:  The Backup Battery gauge registers either 0% or 100%. The percentage is not an indication of the level of charge remaining on the backup battery. An installed and functional battery registers 100%. A total discharge or a battery error registers 0%. Or Tap Battery to view detailed information on the installed battery pack.   For additional information on Advanced Power Settings, see page 7-15. For additional information on the Battery Log Configuration, see page 7-10.   System Resets  See Resetting the Terminal on page 2-11.
DRAFT COPY 11/11/11 3 - 16     Hardware Maintenance  When needed, clean the image engine window and the LCD display with a clean, non-abrasive, lint-free cloth. The terminal can be cleaned with a damp cloth. For additional information on hardware mainte- nance specific to the Dolphin Healthcare Housings, see page 3-11.   Installing a SIM Card and/or Memory Card   SIM Card  Short for Subscriber Information Module, a SIM card stores the subscriber's personal information, GSM/GPRS radio settings, security keys, contacts, etc. SIM cards can be installed in compatible mobile devices, enabling you to switch devices without losing personal and setup information. Before installing the SIM card: •   The service provider must activate the SIM card. •   The terminal must be powered down. Note: If no SIM card is installed, you can still make emergency phone calls (e.g., 9-1-1).  Memory Card  You can expand the terminal’s memory capacity by installing and industry-standard microSD or microS- DHC memory card. Contact a Honeywell sales representative for details on purchasing optional memory cards for your Dolphin terminal. Format all microSD/SDHC cards before initial use.  Installation  1.  Press and hold the Power key  for approximately 5 seconds to put the terminal in Suspend Mode (see page 2-11).  2.  Release the hand strap and slide battery latch away from the battery into the unlock position.  3.  Wait at least 3 seconds. Slide the battery release button away from the stylus slot, then remove the battery.  4.  Remove the screws and the protective shield covering the SIM/memory card socket.  5.  Unlock the SIM card latch by sliding the latch toward the stylus slot.  6.  Lift the latch to reveal the SIM socket and the memory card latch.  Note:  If a SIM card is installed, remove the card to reveal the memory card latch.  4  5  6
DRAFT COPY 11/11/11 3 - 17     If you are not installing a memory card (i.e., microSD or MicroSDHD card), proceed to step 11. 7.  Unlock the memory card latch by sliding the latch toward the top of the terminal.  8.  Lift the latch to expose the memory socket.  9.  Insert the MicroSD or MicroSDHC card.  7  8  9           10.  Close and lock the memory card latch.  10a 10b           11.  Insert the SIM card. Align the chamfered corner of the card with the chamfered corner of the socket.  12.  Close and lock the SIM card latch.  11  12a 12b
DRAFT COPY 11/11/11 3 - 18      13.  Reinstall the shield and screws to protect the sockets.              14.  Install and lock the battery. The terminal automatically starts the power up sequence.  Note:   The terminal does not power ON unless the battery lock is engaged.
4 - 1   4  DRAFT COPY 11/11/11 Using the Scan Image Engine     Overview  The Dolphin terminal houses a compact image engine that instantly reads popular 1D and 2D bar codes and supports omni-directional aiming and decoding for greater flexibility in real-world settings. The image engine can also capture black and white digital images, such as signatures and pictures of dam- aged inventory. With the latest CMOS-based technology, the engine works like a digital camera and enables black and white digital image capture, signature capture, and reading of OCR characters.   Laser Safety  See Laser Safety on page 1-1.  N5603 Beam Divergence Angle  Engines Horizontal Beam Divergence Angle (degrees) Vertical Beam Divergence Angle (degrees) N5603SR/HD 18.1 14.3 N5603ER 13.1 9.9   LED Safety  See LED Safety on page 1-2.   Image Engine Specifications  Engines 1D 2D Image Capture Aiming Pattern Omni-Directional Aiming N5603SR/ER/HD Y Y Y N5603 Red High-Vis Aiming Pattern (page 4-5) Y N5600SR/ER/HD Y Y Y N5600 Green Aiming Beam (page 4-5) Y   Depth of Field  The depth of field measurements used the following parameters: •   Distances are measured from the front of the engine. •   +23°C (+73°F), 0 lux •   Photographic quality codes
DRAFT COPY 11/11/11 4 - 2       Focus N5603/N5600 High Density (HD) N5603/N5600 Standard Range (SR) N5603/N5600 Extended Range (ER) Symbology Distance (in/cm) Distance (in/cm) Distance (in/cm)  Near Far Delta (in/cm) Near Far Delta (in/cm) Near Far Delta (in/cm) 3 mil C39/128 2.0 (5.1) 3.4 (8.6) 1.4 (3.6) - - - - - - 5 mil C39/128 1.4 (3.6) 4.8 (12.2) 3.4 (8.6) 2.7 (6.9) 6.3 (16.0) 3.6 (9.1) 5.4 (13.7) 9.0 (22.9) 3.6 (9.1) 7.5 mil C39/128 1.4 (3.6) 5.6 (14.2) 4.2 (10.7) 2.5 (6.4) 9.2 (23.4) 6.7 (17) 4.2 (10.7) 12.6 (32.0) 8.4 (21.3) 10 mil C39/128 1.4 (3.6) 5.5 (14.0) 4.1 (10.4) 1.6 (4.1) 13.2 (33.5) 11.6 (29.5) 3.1 (7.9) 17.2 (43.7) 14.1 (35.8) 15 mil C39/128 1.3 (3.3) 7.8 (19.8) 6.5 (16.5) 1.8 (4.6) 19.0 (48.3) 17.2 (43.7) 2.4 (6.1) 20.9 (53.1) 18.5 (47.0) 20 mil C39/128 2.3 (5.8) 9.2 (23.4) 6.9 (17.5) 2.2 (5.6) 20.1 (51.1) 17.9 (45.5) 2.9 (7.4) 24.0 (61.0) 21.1 (53.6) 100% UPC 1.9 (4.8) 7.1 (18) 5.2 (13.2) 1.8 (4.6) 16.5 (41.9) 14.7 (37.3) 2.7 (6.9) 19 (43.3) 16.3 (41.4) 5 mil PDF417 1.4 (3.6) 4.8 (12.2) 3.4 (8.6) 2.6 (6.6) 5.2 (13.2) 2.6 (6.6) 6.1 (15.5) 7.4 (18.8) 1.3 (3.3) 6.7 mil PDF417 1.4 (3.6) 4.8 (12.2) 3.4 (8.6) 2.0 (5.1) 6.5 (16.5) 4.5 (11.4) 4.7 (11.9) 9.8 (24.9) 5.1 (13.0) 10 mil PDF417 1.7 (4.3) 6.2 (15.7) 4.5 (11.4) 1.5 (3.8) 11.0 (27.9) 9.5 (24.1) 2.4 (6.1) 15.0 (38.1) 12.6 (32.0) 5 mil MicroPDF 1.8 (4.6) 3.4 (8.6) 1.6 (4.1) - - - - - - 5 mil Data Matrix 1.9 (4.8) 3.1 (7.9) 1.2 (3.0) - - - - - - 10 mil Data Matrix/Aztec 1.7 (4.3) 5.3 (13.5) 3.6 (9.1) 2.2 (5.6) 7.9 (20.1) 5.7 (14.5) 5.1 (13.0) 10.5 (26.7) 5.4 (13.7) 20 mil Data Matrix 2.1 (5.3) 7.8 (19.8) 5.7 (14.5) 2.0 (5.1) 15.3 (38.9) 13.3 (33.8) 3.6 (9.1) 18 (45.7) 14.4 (36.6) 10 mil QR 3.3 (8.4) 5.0 (12.7) 1.7 (4.3) 2.2 (5.6) 7.1 (18.0) 4.9 (12.4) 4.3 (10.9) 10.6 (26.9) 6.5 (16.5) 20 mil QR 2.2 (5.6) 7.9 (20.1) 5.7 (14.5) 2.2 (5.6) 15.5 (39.4) 13.3 (33.8) 2.4 (6.1) 19.6 (49.8) 17.6 (44.7) 32 mil Maxicode 2.4 (6.1) 8.6 (21.8) 6.2 (15.7) 2.5 (6.4) 17.0 (43.2) 14.5 (36.8) 3.9 (9.9) 23.2 (58.9) 19.5 (49.5)
DRAFT COPY 11/11/11 4 - 3     Supported Bar Code Symbologies  Symbology Type Symbology Name 1D Symbologies Codabar  ISBT 128 Codablock F  Matrix 2 of 5 Code 3 of 9  MSI Plessey Code 11 Code 32 Pharmaceutical (PARAF) Code 93  Straight 2 of 5 IATA Code 128  Straight 2 of 5 Industrial EAN with Add-On  Telepen EAN with Extended Coupon Code  Trioptic Code EAN-8  UPC with Add On EAN-13  UPC-A GS1-128  UPC-E GS1 Databar Interleaved 2 or 5 2D Symbologies Aztec  GS1 Databar Codablock A  MaxiCode Codablock F  Micro PDF  PDF417 Data Matrix  QR Code Composite Codes UPC/EAN UCC/EAN GS1 Databar OCR OCR US Money Font MICR (E 13 B) and SEMI Font OCR-A OCR-B Postal Codes Postnet and most international 4-state codes Australian Post British Post Canadian Post China Post Japanese Post KIX (Netherlands) Post Korea Post Planet Code
DRAFT COPY 11/11/11 4 - 4      Decoding  The terminal supports two types of image decoding for use in various bar code reading and imaging applications: full-area imaging and Advanced Linear Decoding (ALD).  Full-Area Imaging Full-area imaging provides omni-directional reading of linear and non-linear 1D and 2D bar codes, OCR, signature capture, and picture taking. When reading all bar code types using full-area imaging, a positive read can be obtained from many positions; see Aiming Beam Options on page 4-5. To achieve the best read, the aiming beam should be centered horizontally across the bar code.  ALD ALD provides fast reading of linear and stacked linear bar codes. To achieve a positive read when read- ing linear 1D and PDF417 bar codes, the aiming beam should be centered horizontally across the bar code. When ALD is enabled, the reader does not read matrix or postal codes.  To Decode a Bar Code  The aiming beam should be oriented in line with the bar code to achieve optimal decoding. A range of 4-10 inches (10-25 cm) from the bar code is recommended.   1.  Tap  > Demos  > Scan Demo  .  2.  Point the Dolphin terminal at the bar code.  3.  Press and hold the SCAN key. The aiming beam or pattern appears and the general notification LED illuminates red.           4.  Center the aiming beam over the bar code; see Aiming Beam Options on page 4-5.  Note:   For optimum performance, avoid reflections by scanning the bar code at a slight angle.  5.  When the bar code is successfully decoded, the general notification LED flashes green and the terminal beeps.  6.  The bar code information is entered into the application in use.
DRAFT COPY 11/11/11 4 - 5       Aiming Beam Options  The aiming beams are smaller when the terminal is held closer to the code and larger when it is farther from the code. Symbologies with smaller bars or elements (mil size) should be read closer to the unit whereas symbologies with larger bars or elements (mil size) should be read farther from the unit.  N5603 Red High-Vis Aiming Pattern  If your Dolphin terminal is configured with a N5603 imager, high-vis aimers frame the bar code for more intuitive aiming. See Laser Safety on page 1-1.      N5600 Green Aiming Beam  Linear Bar Code        2D Matrix Symbol
DRAFT COPY 11/11/11 4 - 6     Capturing Images  The image-capture process is an intuitive, split-second operation for experienced users. By following the basic guidelines, new users can easily develop their own technique and, with practice, quickly learn to adapt it to different application environments.  Image Preview When the imaging process is initiated, the touch screen displays a preview of the object. This is a live video image of what the imager is currently viewing. The live video image has a slightly degraded appearance compared to the captured image. This is normal.  Scan Key On all 7800 terminals, the SCAN key captures images.  File Formats File formats supported for image storage include Bitmap (BMP), JPEG (JPG) and Portable Network Graphics (PNG). The default file format for images is a grayscale JPG.  Compression Digital images have a maximum image size of 640 x 480 pixels and may have up to a 256 grayscale image definition. The image quality and related file size are determined by the data compression method used by the soft- ware application used to take images. The average size of the image file is approximately 4–8K. How- ever, the size of the image depends on the content of the image - the more complex the content, the larger the file size.  Taking an Image  The following steps are basic guidelines for taking images:   1.  Tap  > Demos > Imaging Demo  .  2.  Point the Dolphin terminal at the object.  3.  To preview the image, press and hold the SCAN key. The general notification LED illuminates red.  4.  Adjust the terminal’s position until the object appears on the touch screen the way you want it to appear in the image.  5.  Hold the terminal still and release the SCAN key. The LED flashes green, the screen briefly flashes, and then the captured image appears on the screen.  6.  Tap file Save or Save As.  Note:   Unless otherwise specified by the application in use, the image is saved to the \My Device\My Documents folder.
DRAFT COPY 11/11/11 4 - 7      Enabling the Aimer  You can enable the aiming pattern for imaging in the Imaging Demo. For details about the aimer, see Aiming Beam Options on page 4-5.   1.  Tap  > Demos > Imaging Demo > Setup menu > Aimer.                   2.  The aiming pattern is now enabled for imaging.  Uploading Images  Image files can be uploaded to a host workstation using Microsoft ActiveSync or Windows Mobile Device Center and a Dolphin communication peripheral. For additional information see Connecting and Synchronizing the Terminal and Workstation on page 8-6.
DRAFT COPY 11/11/11 4 - 8
5 - 1            5  DRAFT COPY 11/11/11 Using the Color Camera     Overview  Dolphin 7800 terminals equipped with a 3.0-Megapixels Resolution color camera with Automated Cam- era Control (ACC), and an Application Programming Interface (API) provide easy integration of color pic- ture and video capture into business applications. The camera lens and camera flash are located on the back panel of the terminal.   Taking a picture using the Camera Demo tool   1.  Tap  > Demos  > Camera Demo  .  2.  Adjust the camera settings using the icon menu at the top of the display screen.              3.  Point the terminal's camera lens at the object you want to capture. The camera lens is located on the back panel of the terminal.  4.  Center the object in the touch screen display.  5.  Press the ENT key or tap Snap on the touch screen. The general notification LED illuminates red during picture capture.    Flashlight/ Camera Flash    Camera Lens            Note: Tap the green arrow  to review or edit your pictures.  Tap the green box  to exit the picture review/edit screen.
DRAFT COPY 11/11/11 5 - 2      Options  Tap Options > Camera.          The Camera Options menu appears.  There are five tabs of configurable options accessible from the Camera Options menu. Profile Tab  Display Tab            The profile tab allows you to customize your camera settings, or chose from several predefined profiles designed to provide the best picture quality for common tasks.  Capture Tab  Caption Tab  File Tab                 Taking a picture using the Windows Embedded Handheld 6.5 Camera tool   1.  Tap  > Pictures & Videos  > Camera  2.  Point the terminal's camera lens at the object you want to capture. The camera lens is located on the back panel of the terminal.  3.  Center the object in the touch screen display.  4.  Press the ENT key.  5.  The touch screen displays the captured photo.
DRAFT COPY 11/11/11 5 - 3     6.  Tap OK on the Tile Bar to return to the active viewfinder screen.  Menu  Tap Menu on the Tile Bar at the bottom of the touch screen to adjust the camera settings, switch to video mode, and access additional camera options.   Item  Descriptions  Video  Activate Video Mode  Mode  Set Mode (i.e., Normal, Burst, or Timer)  Resolution  Set Picture Resolution (i.e., QVGA, VGA, SVGA, XGA, UXGA, or QXGA) Zoom  Set Zoom (i.e., x1, x2, or x3) Flash  Set Camera Flash On or Camera Flash Off  Focus  Set Focus Off, Focus On, Focus on Trigger, or Fixed-Focus  Brightness  Set the brightness setting from +2.0 EV to -2.0 EV in .5 EV increments  Full Screen  Switch to full screen mode  Options  Set Camera Options, Video Options, Slide Show Options or General Options   Options  Tap Menu > Options. The Options menu contains four screens:  General Tab  Slide Show Tab  Camera Tab  Video Tab                  Recording Video   1.  Tap  > Pictures & Videos > Camera > Menu > Video  2.  Point the terminal's camera lens at the object you want to capture.  3.  Press the ENT key to start recording.  4.  Tap Stop on the touch screen or press ENT to stop recording.
DRAFT COPY 11/11/11 5 - 4     Uploading Pictures and Videos  Piture and Video files can be uploaded to a host workstation using Microsoft ActiveSync or Windows Mobile Device Center and a Dolphin communication peripheral. For additional information see Connecting and Synchronizing the Terminal and Workstation on page 8-6.
6 - 1        6  DRAFT COPY 11/11/11 Using the Keyboards     Available Keyboards  Note: Contact a sales representative for information on additional keyboard options.   30-Key Numeric Keyboard  46-Key QWERTY Keyboard      2   3   ESC ENT      30-Key Numeric (Calculator) Keyboard  46-Key AZERTY Keyboard       A  Q*    0 .    46-Key QWERTZ Keyboard      F1 Q W E R T     Z U I  O P A* S  D F G     H J K L  Y X C 0 .  V     B N M    All Keyboards Contain the Following:  •   Backlit for easy viewing in various lighting conditions. •   Centrally located Scan key for both right- and left-hand operation. •   Color-coding so you can clearly see the most common keyboard combinations. •   Function, navigation, and modifier keys.
DRAFT COPY 11/11/11 6 - 2     Keyboard Combinations  See 30-Key Numeric Keyboard on page 6-4. See 30-Key Numeric (Calculator) Keyboard on page 6-6. See 46-Key QWERTY Keyboard on page 6-8. See 46-Key AZERTY Keyboard on page 6-11. See 46-Key QWERTZ Keyboard on page 6-14.  Common Buttons  See Using the Function Keys on page 6-2. See Using the Modifier Keys on page 6-3. See Using the Navigation Keys on page 6-3.  Using the Function Keys  Name Key Symbol Function Backlight  or  &  Blue Turns the keyboard backlight on or off.  Note: On terminals with the 30-Key Numeric (Calculator) Keyboard the backlight feature requires the blue modifier key. Flashlight  &  Red  Turns the flashlight on or off. The flashlight is located on the back panel of the terminal.  Backspace   Moves the cursor back one space each time the key is pressed. If you are typing text, it deletes the previous character each time it is pressed.  Enter   Confirms data entry.  Escape   Cancels the current action. Power/End Call Key   The Power key, located in the upper right corner of the keypad, puts the terminal in Suspend Mode or wakes the terminal from Suspend Mode, see Suspend Mode on page 2-11. This key is also used to end/diconnect a phone calls. SCAN Key  Activates the scan and wakes the terminal from Suspend Mode. The key location allows convenient one-handed image-taking and/or bar code decoding.  Space   or Moves the cursor one space. Tab  Moves the cursor to the next tab stop or the next control (on a form).
DRAFT COPY 11/11/11 6 - 3     Using the Modifier Keys  Name Key Function Blue & Red    Blue   Red  The blue and red keys are used in combination with other keys to type special characters and perform system functions. Each keyboard is color-coded to indicate the character typed or function performed when specific keys are pressed immediately after the blue or red modifier key.  Normal Press the blue or red key once to modify only the next key pressed.  Locked Press the blue or red key twice to toggle the modifier lock on or off. If a modifier key is locked on, the next keys pressed are modified until the lock is turned off. This prevents having to press the modifier key each time a key is pressed.  Note: Press the locked modifier key once to temporarily unlock the modifier key for a single key stroke. Shift   The shift key modifies only the next key pressed; it must be pressed before each key you wish to modify. Shift toggles the keyboard between uppercase alphabet mode and lowercase alphabet mode.  Press the shift key twice to toggle Caps Lock ON or OFF.   Using the Navigation Keys  Located in the center of each keyboard for easy access with either hand, the navigation keys navigate the cursor through application screens.   Key  Function  Moves the cursor up one row or line.  Moves the cursor down one row or line.  &  Blue Raises the volume.  &  Blue Lowers the volume.  &  Red Moves the cursor down one page.
DRAFT COPY 11/11/11 6 - 4   2  3   Key Function  &  Red  Moves the cursor up one page.   Moves the cursor one character to the right.  Moves the cursor one character to the left.  Note: Additional functionality varies according to the application in use.  30-Key Numeric Keyboard   Up Navigation Key, Volume Up, Page Up  Down Navigation Key, Volume Down, Page Down   Left Soft Key   Left Navigation Key SCAN Key  Right Soft Key  Right Navigation Key     SEND key   Tab Key  Backlight / Flashlight Key Power Key / END Key    Space Key   Backspace Key   Escape Key   Shift Key ESC ENT  Enter Key      Blue Key  Red Key   30-Key Numeric Keyboard Combinations   Key  Normal  Blue + Normal  Blue + Normal + Shift  Red + Normal Left Soft Key Left Soft Key performs the left function. SCAN SCAN
DRAFT COPY 11/11/11 6 - 5     Key Normal Blue + Normal Blue + Normal + Shift Red + Normal Right Soft Key Right Soft Key performs right function. SEND SEND Cold Boot Cold Boot SEND Left Navigation Left    Up Navigation Volume Up Volume Up Volume Up Page Up Down Navigation Volume Down Volume Down Volume Down Page Down Right Navigation Right Power/END Power On/Off or END Call Warm Boot Warm Boot Power On/Off or END Call TAB TAB back TAB TAB TAB 1 1 @ ? ! @ or ? or ! F1 2 2 abc ABC F2 3 3 def DEF F3 Space Space Backlight Backlight Backlight Backlight flashlight 4 4 ghi GHI F4 5 5 jkl JKL F5 6 6 mno MNO F6 Backspace backspace ESC Escape 7 7 pqrs PQRS F7 8 8 tuv TUV F8 9 9 wxyz WXYZ F9 ENTER Enter Shift Shift
DRAFT COPY 11/11/11 6 - 6     Key Normal Blue + Normal Blue + Normal + Shift Red + Normal Period period asterisk asterisk period Blue Blue      0 0 0 0 F10 Red Red       30-Key Numeric (Calculator) Keyboard   Up Navigation Key, Volume Up, Page Up  Down Navigation Key, Volume Down, Page Down   Left Soft Key   Left Navigation key, Backlight SCAN key  Right Soft Key  Right Navigation key, Flashlight    Send key Power key, End Key   Tab key  Space key   Backspace, Delete key  Escape key   Shift key  Enter key      Blue key  Red key    30-Key Numeric (Calculator) Keyboard Combinations  Key Normal Blue + Normal Blue + Normal + Shift Red + Normal Left Soft Key Left Soft Key SCAN SCAN
DRAFT COPY 11/11/11 6 - 7     Key Normal Blue + Normal Blue + Normal + Shift Red + Normal Right Soft Key Right Soft Key  SEND  SEND  Cold Boot  Cold Boot  SEND Left Left Backlight Left Left Up Volume Up Volume Up Volume Up Page Up Down Volume Down Volume Down Volume Down Page Down Right Right Right Right Flashlight POWER\EN D Power\End Warm Boot Warm Boot Power\End TAB TAB back TAB TAB TAB 7 7 @ or ? or ! @ or ? or ! F7 8 8 abc ABC F8 9 9 def DEF F9 Space Space Dash/Minus - - - - 4 4 ghi GHI F4 5 5 jkl JKL F5 6 6 mno MNO F6 Backspace backspace ESC Escape 1 1 pqrs PQRS F1 2 2 tuv TUV F2 3 3 wxyz WXYZ F3 ENTER Enter Shift Shift
DRAFT COPY 11/11/11 6 - 8     Key Normal Blue + Normal Blue + Normal + Shift  Red + Normal Period period asterisk asterisk period Blue Blue      0 0 plus + 0 F10 Red Red       46-Key QWERTY Keyboard    Up Navigation Key, Volume Up, Page Up  Down Navigation Key, Volume Down, Page Down   Left Soft Key   Left Navigation key SCAN key  Right Soft Key  Right Navigation key     Send key Power key, End Key      Backspace, Delete key   Shift key  Enter key       Tab key  Escape key Blue key  Red key  Space\Symbol key Backlight\Flashlight key    46-Key QWERTY Keyboard Combinations  Key Normal Shift + Normal Blue + Normal Red + Normal Send Send Send Cold Boot Send
DRAFT COPY 11/11/11 6 - 9     Key Normal Shift + Normal Blue + Normal Red + Normal Left Soft Key Left Soft Key SCAN Scan Right Soft Key Right Soft Key Power/End Power/End Power/End Warm Boot Power/End Left Navigation Key Left Up Navigation Up Up Volume Up Page Up Down Navigation Down Down Volume Down Page Down Right Navigation Right Q q Q # (pound/group) F1 W w W 1 F2 E e E 2 F3 R r R 3 F4 T t T ( F5 Y y Y ) F6 U u U _ (underscore) F7 I i I - (minus) F8 O o O + (plus) F9 P p P @ F10 A a A * (asterisk)  S s S 4  D d D 5  F f F 6  G g G /
DRAFT COPY 11/11/11 6 - 10     Key Normal Shift + Normal Blue + Normal Red + Normal H h H : (colon)  J j J ; (semi-colon)  K k K ‘ (single quote)  L l L “ (double quote)  Backspace Backspace Backspace & (ampersand)  Shift Shift Z z Z 7  X x X 8  C c C 9  V v V ? (question mark)  B b B  ! (exclamation point)  N n N \ (back slash)  M m M . (period)  Comma , (comma) < , (comma) , (comma) ENT Enter TAB Tab Back Tab Back Tab Tab Period . (period) > 0 . (period) Blue Blue SYMBOL/ SPACE Space Space SYMBOL Space Red Red Backlight Backlight Backlight Backlight Flashlight ESC Escape
DRAFT COPY 11/11/11 6 - 11   Q   46-Key AZERTY Keyboard    Up Navigation Key, Volume Up, Page Up  Down Navigation Key, Volume Down, Page Down   Left Soft Key   Left Navigation key SCAN key  Right Soft Key  Right Navigation key     Send key Power key, End Key    A  * Backspace, Delete key   Shift key  0 . Enter key    Tab key  Escape key Blue key  Red key  Space\Symbol key Backlight\Flashlight key        46-Key AZERTY Keyboard Combinations  Key Normal Shift + Normal Blue + Normal Red + Normal Send Send Send Cold Boot Send Left Soft Key Left Soft Key SCAN Scan Right Soft Key Right Soft Key Power/End Power/End Power/End Warm Boot Power/End
DRAFT COPY 11/11/11 6 - 12     Key Normal Shift + Normal Blue + Normal Red + Normal Left Navigation Key Left  Up Navigation  Up  Up  Volume Up  Page Up Down Navigation Down Down Volume Down Page Down Right Navigation Right  A  a  A  # (number sign)  F1 Z z Z 1 F2 E e E 2 F3 R r R 3 F4 T t T + (plus) F5 Y y Y _ (underscore) F6 U u U - (minus) F7 I i I = (equal) F8 O o O " (double quote) F9 P p P áü F10 Q q Q * (asterik)  S s S 4  D d D 5  F f F 6  G g G (  H h H )  J j J / (forward slash)  K k K : (colon)  L l L
DRAFT COPY 11/11/11 6 - 13     Key Normal Shift + Normal Blue + Normal Red + Normal Backspace Backspace Backspace    Shift Shift W w W 7  X x X 8  C c C 9  V v V % (percent)  B b B & (ampersand)  N n N  ? (question mark)  M m M  ! (exclamation mark)  Comma , (comma) < @ , (comma) ENT Enter TAB Tab Back Tab Back Tab Tab Period . (period) > 0 . (period) Blue Blue SYMBOL/ SPACE Space Space SYMBOL Space Red Red Backlight Backlight Backlight Backlight Flashlight ESC Escape
DRAFT COPY 11/11/11 6 - 14     46-Key QWERTZ Keyboard    Up Navigation Key, Volume Up, Page Up  Down Navigation Key, Volume Down, Page Down   Left Soft Key   Left Navigation key SCAN key  Right Soft Key  Right Navigation key     Send key Power key, End Key   F1 Q W E R  T Z U I O P A* S  D F G H J K L Backspace, Delete key  Shift key Y X C  0 . V B N M Enter key    Tab key  Escape key Blue key  Red key  Space\Symbol key Backlight\Flashlight key    46-Key QWERTZ Keyboard Combinations  Key Normal Shift + Normal Blue + Normal Red + Normal Send Send Send Cold Boot Send Left Soft Key Left Soft Key SCAN Scan Right Soft Key Right Soft Key Power/End Power/End Power/End Warm Boot Power/End Left Navigation Left Up Navigation Up Up Volume Up Page Up
DRAFT COPY 11/11/11 6 - 15     Key Normal Shift + Normal Blue + Normal Red + Normal Down Navigation Down Down Volume Down Page Down  Right Navigation  Right  Q  q  Q  # (number sign)  F1 W w W 1 F2 E e E 2 F3 R r R 3 F4 T t T + (plus) F5 Y y Y _ (underscore) F6 U u U - (minus) F7 I i I = (equal) F8 O o O “ (double quote) F9 P p P áU F10 A a A * (asterisk)  S s S 4  D d D 5  F f F 6  G g G (  H h H )  J j J / (forward slash)  K k K : (colon)  L l L ‘ (single quote)  Backspace Backspace Backspace    Shift Shift Y y Y 7
DRAFT COPY 11/11/11 6 - 16     Key Normal Shift + Normal Blue + Normal Red + Normal X x X 8  C c C 9  V v V % (percent)  B b B & (ampersand)  N n N  ! (exclamation mark)  M m M ? (question mark)  Comma , (comma) < @ , (comma) ENT Enter TAB Tab Back Tab Back Tab Tab Period . (period) > 0 . (period) Blue Blue SYMBOL/ SPACE Space Space SYMBOL Space Red Red Backlight/ Flashlight Backlight Backlight Backlight Flashlight ESC Escape
7 - 1     7  DRAFT COPY 11/11/11 System Settings     Overview   Customized settings are available on the System Settings menu. Tap  > Settings  and the set- tings screen opens.                      Icon Description Bluetooth  Configures the Bluetooth radio. See Working with the Bluetooth Radio on page 10- 1. Clock & Alarms  Set the system clock, date, time and schedule alarms. See Clock & Alarms on page 7-2. Lock  Password protect the terminal to limit access to the terminal. Sounds & Notifications   Set the sound volume, enable or disable sounds for specific actions, set sound parameters for system notifications and enable or disable vibrator notification. Home  Customize the look and the information displayed on the Home screen. Connections  Establishes network connections settings. See Connections Menu on page 8-1. Personal  Customizes buttons, and set SIP options. See Personal Menu on page 7-3.
DRAFT COPY 11/11/11 7 - 2      Icon  Description System  Adjusts system settings. See System Menu on page 7-7. Microsoft My Phone   This icon is present on Dolphin models equipped with WWAN radio (GSM/UMTS/ GPRS/EDGE) capabilities. Microsoft My Phone synchronizes your phone’s contacts, calendar, tasks, text messages, music, photos, videos, and other documents with your My Phone account at http://myphone.microsoft.com.  Clock & Alarms  The Clock & Alarms settings can be accessed from the Home screen or the Settings Menu. 1.  On the Home screen, tap the line that displays the time and date  OR  Tap  > Settings > Clock & Alarms,  2.  The Clock Settings screen appears. This setting sets the system clock. All scheduled items run according to this setting.                       Tap the arrow to the right of the time zone to open the drop down menu.  Select the appropiate time zone from the menu. Set the correct time and date in the remaining fields and tap OK to save.
DRAFT COPY 11/11/11 7 - 3         Personal Menu   To access the Personal Menu, tap  > Settings  > Personal  . The screen opens displaying the Personal Menu.                       Icon Description Buttons  Program the side buttons to perform specific tasks. See Buttons on page 7-3. Owner Information   Enter your contact information (e.g., name, company, address, telephone number and E-mail address). Phone   This Phone icon is present on Dolphin models equipped with WWAN radio (GSM/ UMTS/GPRS/EDGE) capabilities. Tap this icon to set up user parameters. See Setup Options on page 9-5.  Buttons  The Buttons setting programs certain keyboard buttons to launch applications or execute commands.  Enable HotKeys  Default Buttons setting assignments are inactive until you enable the HotKeys Power Tool.  Tap  > Power Tools and tap the HotKeys icon  once. HotKeys is enabled, and the button assignments in the Buttons setting are active. For more information about the HotKeys Power Tool, refer to the Dolphin Power Tools User’s Guide, http://www.honeywellaidc.com/ is available for download from the web at www.honeywellaidc.com.
DRAFT COPY 11/11/11 7 - 4      Changing Button Assignments   1.  After HotKeys is enabled, tap  > Settings > Personal  > Buttons  .                       Note: The buttons that appear on this window are the only buttons that can be programmed via the Buttons setting. You cannot add buttons to this window.  2.  To change button assignment, tap on the name of the button in the Button column, and then select a program or command in the Assign a program drop down list.  3.  Tap OK to save.  4.  Press the button to verify that the program is launched or action performed.  Available Applications  The Assign a program list contains the applications installed on the terminal. If there is a program installed that you would like to see in this list, paste a Shortcut to the program in the \\Windows\Start Menu\Programs folder. For instructions about creating shortcuts, see Using File Explorer on page 7-5.  Additional Functions  The Assign a program list also contains the following commands:   Command  Description  <Context Menu>  Performs the same function as tap-and-hold to open the context menu for the control.  <Home>  Returns to the Home screen.  <Input Panel>  Opens the soft input panel.  <Left Softkey>  Opens the menu or performs the action displayed on the left side of the Command bar.  <None>  Nothing happens when the button is pressed.  <OK/Close>  Performs the same function as tapping OK on the screen.
DRAFT COPY 11/11/11 7 - 5       Command  Description  <Right Softkey>  Opens the menu or performs the action displayed on the right side of the Command bar.  <Rotate Screen>  Changes the screen orientation from portrait to landscape.  <Scan1>  Activates the scanner/imager.  <Scan2>  Activates the scanner/imager.  <Scroll Down>  Scrolls down in the open application.  <Scroll Left>  Scrolls left in the open application.  <Scroll Right>  Scrolls right in the open application.  <Scroll Up>  Scrolls up in the open application.  <Start Menu>  Opens the Start menu.   Using File Explorer  If you do not see the program listed, you can either use File Explorer to move the program or ActiveSync on the workstation to create a shortcut to the program and place the shortcut in the Start Menu folder.  Note: We recommend that you Copy and Paste Shortcut so that you do not alter your program configurations by accident. Using Copy and Paste Shortcut (as opposed to Cut and Paste) ensures that the program files remain where they need to be for the system to find them to perform system functions.    1.  Tap  > File Explorer  , and navigate to the program (My Device > Program Files).              2.  Tap and hold on the program, then tap Copy on the pop-up menu.
DRAFT COPY 11/11/11 7 - 6       3.  Navigate to the Windows folder and open the Start Menu (My Device > Windows > Start Menu > Programs), tap and hold a blank area of the window, and tap Paste Shortcut on the pop-up menu.                Note: If there is no blank space available in the window, tap on Menu > Edit > Paste Shortcut.             4.  Tap  to verify that the program now appears on the Start menu.  Using ActiveSync on the Workstation  Here, you are performing the same basic process as on the terminal, except that you are using the Explore utility (Windows Explorer) to copy and paste the shortcut. 1.  Open ActiveSync > Explore and navigate to the program.  2.  Right-click on the program and select Create Shortcut.  3.  Select the shortcut, right-click, and select Cut.  4.  Navigate to the Start Menu folder (Windows > Start Menu > Programs).  5.  Right-click on an empty area and select Paste Shortcut.  6.  On the terminal, tap the Start menu.  7.  Verify that program appears.
DRAFT COPY 11/11/11 7 - 7     System Menu  The System menu enables you to verify and sometimes alter system parameters. To access the System menu, go to Start > Settings > System. Tap the appropriate icon to open that system setting.                       Icon See Page About  See About on page 7-8. Backlight  See Backlight on page 7-9. Battery  See Battery on page 7-10. Certificates  See Certificates on page 7-10. Encryption  See Encryption on page 7-11. Error Reporting  See Error Reporting on page 7-11. External GPS  See External GPS on page 7-11.
DRAFT COPY 11/11/11 7 - 8      Icon See Page Five Volt Control  See Five Volt Control on page 7-12.  Managed Programs   See Managed Programs on page 7-13. Memory  See Memory on page 7-14.  Power   See Power on page 7-15.  RIL   See RIL on page 7-15. Regional Settings  See Regional Settings on page 7-15.  Remove Programs   See Remove Programs on page 7-16. Screen  See Screen on page 7-17.  Smart Sensors   See Smart Sensor on page 7-12.  Task Manager   See Task Manager on page 7-18.  About  The About system setting displays specific information about the terminal. It contains three screens:  Version Screen  Displays the information about the software, operating system, and processor. Device ID Screen  Displays the information the terminal uses to identify itself to other devices. It can be important to know this information if the Dolphin terminal is going to be part of a networked system of devices. Device name: Displays the system’s default name. This is the name used by ActiveSync. Description: Displays the description of the device ID. Copyrights Screen: Displays important copyright information.
DRAFT COPY 11/11/11 7 - 9      Backlight  The Backlight system setting enables you to customize backlight functionality for the display. The back- light for the color display is user-defined. The Backlight system setting screen contains three tabs: Bat- tery Power, External Power, and Brightness.   Tap  > Settings > System > Backlight.  Battery Power Tab  External Power Tab  Brightness Tab                   The Battery Power tab determines the backlight timeout when the terminal is running on battery power. The External Power tab determines the backlight timeout when the terminal is running on external power. The options on the power tabs are the same.  Turn off backlight:  Select how many minutes you want to elapse before the backlight automatically turns off.  Turn on backlight:   Select this option if you want the backlight to turn on when the button is pressed or the touch screen is tapped.  The Brightness tab determines the backlight intensity. Move the slider to set the intensity of the back- light. The default is 8.
DRAFT COPY 11/11/11 7 - 10         Battery  The Battery system settings menu contains two tabs: Battery Status and Log Config. The Battery Sta- tus tab provides the status of the main battery pack (e.g., Battery Time to Full or Battery Time to Empty, Voltage, Current, Temperature, Chemistry, and Serial Number). The Log Config Tab allows you to con- figure the BatteryLogFile.   Tap  > Settings > System > Battery  Battery Status Tab  Log Config Tab       When  external  power  is supplied to the terminal, “Battery Time to Full” is listed. When power is supplied by the battery pack, “Battery Time to Empty” is listed.         Certificates  Certificates shows you the certificates that are recognized by the operating system. It contains three screens.  Intermediate Screen  Personal Screen  Root Screen
DRAFT COPY 11/11/11 7 - 11        Encryption  Encryption gives you the option of encrypting files placed on storage cards so that those files cannot be read by any other device.             Error Reporting  Error Reporting gives you the option of enabling or disabling the error reporting function of Windows Embedded Handheld 6.5.                   External GPS  External GPS determines which port a third-party GPS software application can use to access the GPS receiver. Access Screen  Hardware Screen  Programs Screen              Note: You need the installation parameters from the GPS manufacturer to configure the connection.
DRAFT COPY 11/11/11 7 - 12      Five Volt Control  Five Volt Control gives you the option to manually enable 5V output to supply power to an external device. By default, 5-Volt Output automatically turns on when AC power is applied to the terminal. If you want to use a USB memory stick without AC power, then you must manually turn on the 5-Volt Output. Do not leave 5-Volt output enabled when you are not using it to supply power to an external device.  Smart Sensor  The Smart Sensor configuration utility enables you to configure the Dolphin’s integrated accelerometer, and motion settings.   Tap  > Settings > System > Smart Sensor.  Motion Settings  Motion Settings enable you to customize how the terminal responds to motion and object orientation for advanced power management.  Display Settings enables or disables Auto Display Orientation. When enabled, the Dolphin's display automatically switches between portrait and landscape depending on how you hold the terminal.                Power Management Settings customize how the terminal responds to object orientation and motion. •   Save power by turning off the display or suspending the terminal when it is placed face down. •   Modify the Motion Detection settings to wake the terminal from suspend mode or prevent the terminal from entering suspend mode when motion is detected.
DRAFT COPY 11/11/11 7 - 13       Event Track displays an event log summary of detected free fall events exceeding 2 ft. over 250 ms. The summary includes the time, date, and duration of the most recent 50 events. Several options are provided for audible notification of free fall events.             Accelerometer Calibration   Tap Start to calibrate the integrated accelerometer sensor used for motion detection. When calibration is complete, the "Accelerometer Calibration Finished!" message window appears.                 Managed Programs  Managed Programs are a list of programs that are managed if enrolled to enterprise domain. Managed Programs is the client-side that works with the server product System Center Mobile Device Manager (MDM). MDM consists of MDM Gateway Server and one or more computers that run MDM Device Man- agement Server; MDM Enrollment Server; and Microsoft SQL Server® 2005 databases. It lets system administrators:  •   provide an authenticated connection to Line of Business (LOB) applications, managed Group Policy, and application packages. •   use Group Policy and software packages to manage the enrolled Windows phones (enforce policy, wipe devices, etc.). •   manage the requests for and retrieving of certificates for devices and for creating the Active Directory® Domain Service objects that represent these devices. By using these objects, you can manage the devices as if they were members of a domain.
DRAFT COPY 11/11/11 7 - 14     Memory  The Memory applet shows the capacity and usage of the Storage and Program portions of the Flash file system. The Storage portion includes the IPSM folder, which can be detailed under the Storage Card tab. When the Program portion becomes too full, you can use the Task Manager to remove any unneces- sary tasks.  Main Screen This screen displays the usage statistics of the flash memory.                Storage Card Screen  This screen displays the current capacity and usage sta- tistics of the selected memory type: IPSM, RAMDISK or Storage Card. Select the memory type from the drop-down list. IPSM is selected by default.  Total storage card memory = The total MB of memory capacity of the IPSM, RAMDISK or Storage Card.  In use = The MB currently being used.  Free = The MB that is still available for use.     IPSM—Short for Internal Persistent Storage Manager. Data or programs stored in the IPSM are not affected when the operating system is upgraded. Autoinstall programs, for example, are stored in \\IPSM\Honeywell\Autoinstall so that they are always installed after an operating system upgrade or factory reset. Contact a Honeywell technical support representative for more information on how to perform a factory reset. For contact information, see Technical Assistance on page 18-2. RAMDISK—Is a disk image that resides in RAM and threfore is faster than IPSM or any other system named folder. RAMDISK is cleared when a hard reset or a factory reset is performed. Storage Card—You can install one memory card in Dolphin terminals (see Installing a SIM Card and/or Memory Card on page 3-16). If a storage card is installed in the terminal, you can select it in the drop-down list and see capacity and usage statistics for the card.
DRAFT COPY 11/11/11 7 - 15      RIL  The RIL Information screen displays useful statistics for the GSM WAN Voice module (PH8). To verify whether or not the GSM radio is enabled, check the Dolphin Wireless Manager (see page 8-4).  Power  Power system settings contains two tabs: Battery and Advanced   Tap  > Settings > System > Power  Battery Tab   The battery tab displays the power level status of the main battery and the status of the backup battery.  Note: The Backup Battery gauge registers either 0% or 100%. The percentage is not an indication of the level of charge remaining on the backup battery. An installed and functional battery registers 100%. A total discharge or a battery error registers 0%.   For detailed information on the main battery pack, see Battery on page 7-10.      Advanced Tab   Determines power time-outs.  For On battery power, select from the drop-down list, the number of minutes of inactivity you want to pass before the terminal powers off when running on battery power.  For On external power, select from the drop-down list, the number of minutes of inactivity you want to pass before the terminal powers off when running on external power.          Note: When the terminal “powers off”, it enters Suspend Mode, see page 2-11 for additional information.  Regional Settings  Regional Settings enables you to customize the appearance and formatting to your geographic region. Specifically, you can customize numbers (i.e., number of decimal places allowed), currency (i.e.,using the $ or € symbol), time, and date. These specifications apply to all screens, including the Home screen. The Region tab displays an overview of the region selected in the drop-down list at the top.
DRAFT COPY 11/11/11 7 - 16     The terminal is loaded with a number of pre-programmed regional settings. Select one from the list and the results appear on the screen. To see specific settings or to change a specific setting, tap on one of the items on the horizontal scroll bar (i.e., Region, Number, Date), make the change, and tap OK to save.  Remove Programs  Remove Programs enables you to remove programs installed on the terminal. Any program (usually CAB or DLL files) stored in the \\IPSM\Honeywell\Autoinstall folder re-installs after a software upgrade or a factory reset. If a program is manually removed using the Remove Programs application, the program does not re-install on a hard or soft reset.  Note: A program (file) does not automatically install if it is added to the \\IPSM\Honeywell\Autoinstall folder and a hard or soft reset is performed.  For information on program installation, see Installing Additional Software on page 8-8.  For information about the system resets, see Resetting the Terminal on page 2-11. See Honeywell sup- port for more information on how to perform a factory reset. 1.  Tap Remove Programs. In the list, select the program you want to remove.                   2.  Tap Remove. The following message appears:                   3.  Tap Yes. Wait while the program is removed.  4.  Verify that the program no longer appears in the list.

Navigation menu