Honeywell 9700 MSCR 97 QS_6 Panel User Manual To The 7e602365 A23f 4492 9e58 933ab22ac81b

User Manual: Honeywell 9700-MSCR to the manual

Open the PDF directly: View PDF .
Page Count: 2

97-MSCR-QS Rev A

12/10

Dolphin™ 9700-MSCR

Magnetic Stripe and Smart Card Reader

Quick Start Guide

Introduction

The Magnetic Stripe and Smart Card Reader (MSCR) for

the Dolphin 9700 enables easy data capture with the swipe

of a magnetic stripe card or smart card insertion. The MSCR

snaps onto the bottom panel of the Dolphin terminal for easy

installation or removal.

Software Requirements

Before you connect the Dolphin terminal to the 9700-MSCR,

make sure you have the most current software installed. To

check the terminal’s system information, tap

Start > Power Tools > SysInfo.

The kernel version must be 20.01 or later in terminals

running Windows Mobile 6.5 Classic. In terminals running

Widow Mobile 6.5 Professional, the kernel version must be

21.01 or later.

Service pack version 7

or later is required.

D9700 MSCR Demo Application

Not all Dolphin 9700 terminals are equipped with the D9700

MSCR Demo application. For download and installation

instructions, see Installing the MSCR Demo Application, in

this quick start guide.

Application Developer Note

For maximum battery performance, turn off power to the

9700-MSCR when the module is not in use.

Attaching the MSCR to the Dolphin

1. Press the Power key to put the terminal in Suspend

mode.

2. Remove the stylus from the Dolphin 9700 stylus slot

and store it in the stylus loop on the hand strap.

3. Slide the MSCR onto the terminal until the MSCR

snaps in place.

Note: To improve unit grip and reduce the possibility of

accidental drop, Honeywell recommends using the

supplied hand strap while operating the terminal with

the MSCR attached.

4. Press the Power key to wake the terminal.

Indicator LED

Magnetic Stripe

Card Slot

Dolphin 9700

Smart Card Slot

with Rubber Cover

I/O Connector

Release Latch

MSCR LED Indicator

The single LED indicator located on the top surface of the

MSCR housing denotes the communication status and the

selected function (i.e., Magnetic Stripe Reader or Smart

Card Reader).

This color and status means . . .

Green active Green LED activity indicates the

Magnetic Card function is

selected.

Slow Flashing The MSCR has power and is idle.

Solid A magnetic stripe card is being

swiped/read.

Fast Flashing The MSCR has successfully read

the magnetic card.

This color and status means . . .

Yellow active Yellow LED activity indicates the

Smart Card function is selected.

Slow Flashing The MSCR has power and is idle.

Fast Flashing The Dolphin is performing smart

card read/write operations.

Using the MSCR Demo Application

You can use the MSCR Demo application to verify that the

Dolphin 9700 terminal can receive data from the MSCR.

Starting the MSCR Demo Application

1. On the Dolphin terminal, tap Start > File Explorer >

My Device > Program Files > D9700 MSCR Demo >

D9700MSCRTest.

Note: Not all Dolphin 9700 terminals are equipped with the

D9700 MSCR Demo application. For download and

installation instructions, see Installing the MSCR Demo

Application, in this quick start guide.

2. Connect the MSCR to

the Dolphin terminal.

3. Verify COM1 is

selected from the pull

down menu.

4. Check the box next to,

Power.

Note: The LED indicator on the MSCR emits a single long

green flash and then flashes approximately every three

seconds. By default, the Magnetic Stripe Reader function

is activated when power is supplied to the MSCR.

Testing the Magnetic Stripe Reader

1. Swipe a magnetic stripe card. The green LED stays illu-

minated for the duration of the swipe.

Note: You can swipe the card from

either the left or the right. Make

sure the magnetic stripe of the

card is facing down, toward the

I/O connector as shown.

2. The LED rapidly flashes green four times to indicate a

good read. The data from the card appears on the

terminal’s screen.

Note: If the LED does not flash, the card swipe was not

successful.

Testing the Smart Card Reader

1. Remove the Rubber Cover

protecting the smart card

slot.

Note: Do not discard the rubber

cover. The cover protects

the smart card slot when

not in use.

2. Select SCR. The LED

indicator changes to yellow,

emits a single long flash,

and then flashes every

3 seconds.

3. Insert a smart card into the slot

below the serial port. Do not

remove the smart card from the

reader.

Note: Make sure the contacts of

the card are facing up, toward

the keypad on the terminal.

4. Tap the ATR button in the D9700MSRTest window.

Note: The yellow LED rapidly flashes during data collection.

If the LED does not flash rapidly, the MSCR is not

accessing the data on the smart card.

5. The data from the

card appears on the

terminal’s screen.

Installing the MSCR Demo Application

Not all Dolphin 9700 terminals are equipped with the D9700

MSCR Demo application. To download and install the

application:

1. Go to www.honeywellaidc.com. Select Support >

Downloads. Click Software and then select

DOLPHIN9700 from the product list.

2. Download the Honeywell D9700 MSCR Demo.cab file

to the workstation.

3. Connect the terminal to the workstation using a

Honeywell communication peripheral.

4. Open ActiveSync and click Explore.

5. Click on the My Windows Mobile-Based Device

folder and copy the downloaded file to the IPSM >

Autoinstall folder on the terminal.

6. Do one of the following:

• Tap on the Honeywell D9700 MSCR Demo.cab

inside the Autoinstall folder to install the application.

• Press and hold the RED + ENT keys on the terminal

to perform a hard reset (cold boot). The application

will install as part of the Autoinstall process that

occurs during each hard reset.

Note: A hard reset erases all of the data stored in RAM memory and

all RAM installed applications!

Using ScanWedge to Test the MSCR

ScanWedge is a utility on Dolphin Terminals that can send

data received from the decoder, serial port, or IrDA interface

to the foreground application. The foreground application is

the open software application whose window is currently

active on the screen.

Note: The ScanWedge utility does not support smart card reading.

Set Up and Start ScanWedge

1. Tap Start > File Explorer. Navigate to the IPSM folder.

2. Tap on the ScanWedge.exm file to open it.

3. Drill down to the Comm folder.

4. Locate the Key column near the bottom of the screen.

Tap and hold on Enable.

5. Select Modify. Set the Value to Enable.

6. Tap OK on the Navigation Bar.

7. Using the same procedure in steps 4 through 6, set the

BaudRate to 9600 and PowerOut to Enable.

8. Tap OK.

9. Tap Start > Power Tools > ScanWedge.

Test Swipe a Magnetic Stripe Card

1. Tap Start > Notes.

2. Swipe a magnetic stripe card. The green LED stays

illuminated for the duration of the swipe.

Note: You can swipe the card from either the left or the right.

Make sure the magnetic stripe of the card is facing down,

toward the I/O connector.

3. The LED rapidly flashes green four times to indicate a

good read. The data from the card appears on the

terminal’s screen.

Removing the MSCR from the Terminal

1. Press the Power Key to put

the Dolphin terminal in

Suspend mode.

2. Press in the release latches

located on the left and right

sides of the MSCR.

3. Slide the MSCR off the

terminal base.

Charging the Terminal

The MSCR facilitates cradle and cable charging of the

Dolphin 9700 while attached to the bottom of the terminal.

The MSCR is compatible with all Dolphin

9700 charging cables, and the 9700

HomeBase™, ChargeBase™, eBase™,

and Net Base.

Note: The Dolphin 9700 with an attached

MSCR cannot be used with the Dolphin

9700 Mobile Base or Mobile Mount

peripherals. If you are using one of these

peripherals, you can temporarily snap-fit

the MSCR to the terminal to swipe cards,

then remove the MSCR to connect the

terminal to the peripheral.

2

2

3

Technical Assistance

Contact information for technical support, product service,

and repair can be found at www.honeywellaidc.com.

User Documentation

Refer to www.honeywellaidc.com for detailed user

documentation or for localized versions of this Quick Start.

Patents

For patent information, please refer to

www.honeywellaidc.com/patents.

Limited Warranty

Refer to www.honeywellaidc.com/warranty_information for

your product’s warranty information.

Disclaimer

Honeywell International Inc. (“HII”) reserves the right to

make changes in specifications and other information

contained in this document without prior notice, and the

reader should in all cases consult HII to determine whether

any such changes have been made. The information in this

publication does not represent a commitment on the part of

HII.

HII shall not be liable for technical or editorial errors or

omissions contained herein; nor for incidental or

consequential damages resulting from the furnishing,

performance, or use of this material.

This document contains proprietary information that is

protected by copyright. All rights are reserved. No part of

this document may be photocopied, reproduced, or

translated into another language without the prior written

consent of HII.

Web Address: www.honeywellaidc.com

Trademarks

Dolphin, HomeBase, Mobile Base, ChargeBase, eBase and

Net Base are trademarks or registered trademarks of Hand

Held Products, Inc. or Honeywell International Inc.

Microsoft and Windows is a trademark or registered

trademark of the Microsoft Corporation.

Other product names mentioned in this manual may be

trademarks or registered trademarks of their respective

companies and are the property of their respective owners.

©2010 Honeywell International Inc. All rights reserved.