Honeywell Hd3Vc4Sax Users Manual HD3VC4 3 Inch Dome Camera Quick Install Guide
HD3VC4SAX HD3VC4_3InchDomeCameraQuickInstallGuide_EN
HD3VC4SAX to the manual 35794994-5a39-4a89-bb79-7039b0e823bb
2015-01-23
: Honeywell Honeywell-Hd3Vc4Sax-Users-Manual-261797 honeywell-hd3vc4sax-users-manual-261797 honeywell pdf
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
3 Inch Dome Camera HD3VC4SHR/HD3VC4SA/HD3VC4SHRX/HD3VC4SAX Quick Install Guide Operating Conditions Removing the Dome Cover • 1. Avoid viewing very bright objects (example, light fixtures) for extended periods. Avoid operating or storing the unit in the following locations: • Extremely humid, dusty, hot/cold environments (where the operating temperature is outside the recommended range of 14°F to 122°F [-10°C to +50°C]) • Close to sources of powerful electromagnetic radiation, such as radio or TV transmitters • Close to fluorescent lamps or objects reflecting light • Under unstable light sources (may cause flickering) • Figure 4 Camera Adjustment Gently turn the dome cover (#5 on Figure 2) counter-clockwise to unlock and pull free of the housing. Remove the inner liner (#4) by gently pulling it free of the two notches (#2) in the housing (#1). Set the dome (and liner) aside. 2. 3. 5 1 2 3 Figure 2 4 Dome Cover Removal 4 — Legend 1 2 3 1 Tilt adjustment bracket and thumbnuts (x2) for vertical adjustment 2 Axis ring for horizontal rotation for wall mount and tilted ceilings 3 Zoom lever 4 Focus lever 5 Rotate 3D assembly in base for horizontal adjustment 4 The unobtrusive, compact design of the HD3VC4S Series 3 Inch Dome Camera is ideal for indoor installations in commercial and residential environments. Before You Begin Unpack Everything Check that the items received match those listed on the order form and packing slip. The HD3VC4S Series Camera packing box should include, in addition to this Install Guide: • One fully assembled camera • One hardware kit • One 2nd video monitor output cable • One mounting template If any parts are missing or damaged, contact the dealer you purchased the camera from or call Honeywell Customer Service. 1 — Legend Power Supply This dome camera can operate on 24 VAC or 12 VDC. Document 900.0824 - 09/06 - Rev 1.01 Note 1. 3. Optional Camera Settings See Figure 5 for location on the camera board of the camera adjustment functions described below. Place the mounting template (supplied) on the mounting surface and mark the holes (see Figure 3). Drill two holes, then insert the screw anchors into the holes. Secure the camera housing to the wall/ ceiling with the TP4 x 15 mm tapping screws supplied. 2. It is important that you lock the zoom and focus levers after making adjustments. This will avoid the positions moving (for example, from temperature changes or vibrations). Figure 5 Camera Adjustment Functions 1 3 LEVEL L H 1 : BLC 2 : AGC 3 : DC/AES 4 : LL 2 4 V PHA SE + - 1 2 3 4 Depending on the material of your mounting surface, you may require different screws and anchors than those supplied. Figure 3 1 2 3 4 ON OFF V P HAS E + - ON O FF MON 1:BLC 2:AG C 3:DC/AE S 4:LL Camera Installation 1 Camera Parts 2 b a 1 M o u n t in g T e m p la t e L o g o D i r e c ti o n 5 — Legend 1 LEVEL adjustment pot (Iris level) 2 V Phase adjustment pot (24 VAC only) 3 Mode setting DIP switches 4 Monitor out 5 Camera mounting holes 3 2 Note MON PC 1 :B L C 2 :A G C 3 :D C /A E S 4 :L L 3 1 2 3 4 4 L 5 1 Conduit hole used for surface run power/video connector 3 — Legend 1 Screw anchors (x2), supplied 2 Camera housing 2 Mounting template 3 Dome cover 3 TP4 x 15 mm tapping screws (x2) supplied 4 Zoom lever 5 Focus lever Adjusting the Camera Position a Video output connector b 24 VAC/12 VDC power input connector (red +, black -) The HD3VC4S Series camera has three axes for positioning the camera. While monitoring the picture on the monitor, adjust the camera position as follows: Note See Figure 5 for an explanation of the camera board settings. Please use the supplied DC Iris and Line lock adjustment tool to adjust picture brightness and phase adjustment. TOP Operating Notes Dome cover 5 Caution Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The manufacturer declares that the equipment supplied with this guide is compliant with the essential protection requirements of the EMC directive 89/336/EEC and the Low Voltage Directive LVD 73/23 EEC, conforming to the requirements of standards EN 55022 for emissions. 5 2. Mounting the Camera Installation Figure 1 Manufacturer’s Declaration of Conformance Inner liner Loosen the Zoom lever (#3) counterclockwise a little, then rotate the Zoom lever and determine the image view. Loosen the Focus lever (#4) counterclockwise a little, then adjust the focus for optimum picture sharpness. Re-tighten the Zoom lever and Focus lever after adjustment. LE V E L H L Information to the User: This equipment has been tested and found to comply with the limits for a Class A digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This Class A digital apparatus complies with Canadian ICES-003. 4 Follow Figure 1 to connect the video output connector (a) and 24 VAC/12 VDC power connector (b). Note The HD3VC4S Series is a fully-integrated enclosure with camera and lens. FCC Compliance Statement Tilt adjustment bracket and thumbnuts ON OFF THIS SYMBOL INDICATES THAT IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS ACCOMPANY THIS UNIT. 3 1. MON CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Notches (x2) PC RISK OF ELECTRIC SHOCK 2 Caution For DC power supply use, make sure the polarity is correct to avoid malfunction and/or camera damage. THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THE UNIT. CAUTION Camera housing Connecting the Wiring LEVEL WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product (applicable in the European Union and other European countries with separate collection systems). This product should be disposed of, at the end of its useful life, as per applicable local laws, regulations, and procedures. 1 3. Please read this guide carefully before you install the HD3VC4S Series 3 Inch Dome Camera. Keep this guide for future reference. WARNING! The use of CSA Certified/UL Listed Class 2 power adapters is required to ensure compliance with electrical safety standards. WARNING! To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. 5 H Installation and servicing should be performed only by qualified and experienced technicians to conform to all local codes and to maintain your warranty. Adjusting the Lens 2 — Legend V PH A SE + - Warnings, Operating Notes Introduction TO P Document 900.0824 - 09/06 - Rev 1.01 Horizontal Adjustment Rotate the 3D assembly in the base. Do not turn the assembly more than 360° as this may cause the internal cables to twist and disconnect or break. Vertical Adjustment After loosening the thumbnuts, position the camera as desired, then finger-tighten the thumbnuts to set the position. Horizontal Rotation For Wall Mount and Tilted Ceilings Rotate the lens base (maximum 360°) until you are satisfied with the field of view. Picture Brightness Use the LEVEL screw (#1) to compensate for the iris level. L (low) makes the picture darker. H (high) makes the picture brighter. Phase Adjustment Use the V Phase Adjustment Pot (#2) to adjust the phase difference between cameras. Make sure Switch 4 is ON to activate the Line lock function (AC operation only). DIP Switches Set the DIP switches (#3) to activate or deactivate the following functions: Switch Description 1 BLC (Backlight Compensation). Set to ON to have the camera adjust the exposure to compensate for situations where the subject is lit from behind. The factory default setting is OFF. 2 AGC (Automatic Gain Control). Set to ON (default) to have the camera adjust the picture for low light conditions. 3 DC/AES Mode. Leave in ON position only. 4 LL (Line Lock). Set the camera synchronization to internal or line lock (line lock is only available with 24 VAC). The factory default setting is OFF. Product Dimensions To attach the dome cover, follow Figure 2: 1. Use a soft, lint-free cloth to wipe the dome cover clean and remove fingerprints. 2. Attach the inner liner (#3) to the Tilt adjustment thumbnuts (#2). Push down until it clicks into place. 3. Place the dome (#4) on the unit. Make sure all three dome tabs (#5) are inside the housing opening. 4. Turn the dome gently clockwise until it locks in place. Figure 6 Camera Dimensions Specifications Contact Information Video Signal Specifications Honeywell Video Systems (Head Office) 2700 Blankenbaker Pkwy, Suite 150 Louisville, KY 40299, USA www.honeywellvideo.com ℡ +1.800.796.2288 Video Standard: NTSC, PAL Scanning System: 4.33” (110 mm) 2 625 lines, 2:1 interlace (PAL) Image Sensor: 1/3” Interline Transfer CCD Number of Pixels (H x V): 768 x 494 (NTSC) 510 x 492 (NTSC) 752 x 582 (PAL) 500 x 582 (PAL) Minimum Illumination: 0.6 lux @ F1.3 Horizontal Resolution: 4 0.2 lux @ F1.3 540 TVL Video Output: 0.2” (5 mm) diameter Legend 50 dB (AGC Off) 12 VDC: Internal, 24 VAC: Line lock Auto Gain Control: On/off, switchable BLC: On/Off, switchable AI/AES Selection: 1 Camera housing 2 Tilt adjustment bracket and thumbnuts 3 Inner liner 4 Dome cover 5 Dome tabs (x3) On/off, switchable Automatic Electronic Shutter: 1/60 - 1/100,000 sec (NTSC) 1/50 - 1/100,000 sec (PAL) Lens Type: 3.27” (83 mm) 350 TVL 1.0 Vp-p @ 75 Ohms S/N Ratio: Sync System: 5 Standard Res 525 lines, 2:1 interlace (NTSC) (AGC on, 50 IRE) 1 3 NTSC, PAL High Res 3.91” (96.3 mm) Attaching the Dome Cover 2.8 mm to 10 mm Vari-focal Auto Iris, F1.3 Lens Iris Control: Direct Drive (DC) AI Angle of View (Lens): Wide Tele 129.0° (D), 100.2° (H), 73.3° (V) 34.3° (D), 27.4 (H), 20.5° (V) Routine Maintenance Warranty and Service Focal Length: f = 2.8 mm to 10 mm White Balance: ATW • Subject to the terms and conditions listed on the Product warranty, during the warranty period Honeywell will repair or replace, at its sole option, free of charge, any defective product returned prepaid. In the event you have a problem with any Honeywell product, please call Customer Service for assistance or to request a Return Merchandise Authorization (RMA) number. Call 1.800.796.CCTV (North America only). Be sure to have the model number, serial number, and the nature of the problem available for the technical service representative. Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped to Honeywell without a clearly identified Return Merchandise Authorization (RMA) number may be refused. Gamma: 0.45 Temperature: Operating Storage 14°F to 122°F (-10°C to 50°C) -4°F to 140°F (-20°C to 60°C) Europe and United Kingdom Relative Humidity: 0% to 90%, non-condensing For warranty information please contact your Honeywell dealer. Regulatory • The dome cover is an optical part. Use a soft, dry cloth to remove any fingerprints or dust. Clean the camera housing with a soft, dry cloth. For more stubborn stains, use a cloth dampened with a small quantity of neutral detergent, then wipe dry. Caution Do not use volatile solvents such as alcohol, benzene or thinners to avoid damaging the surface finish. Cable Guidelines Maximum Power Supply Cable Length (feet/meters) Cameras With AC/DC Power Supplies Wire gauge Total load Power supply 24 AWG 22 AWG High Res 12 VDC 15 VDC 24 VAC 89/27 348/106 991/302 148/45 374/114 597/182 561/171 1427/435 2273/693 1601/488 4061/1238 6462/1970 Std Res 12 VDC 15 VDC 24 VAC 18 AWG 16 AWG 236/72 384/117 977/298 1555/474 420/128 679/207 1729/527 2752/839 1155/352 1866/569 4736/1444 7541/2299 Caution Calculations are based on an unregulated linear power supply, which would be the worst case. Using a regulated or switching power supply can increase the cable distance. Honeywell recommends using a CSA Certified/UL listed Class 2 power adapter to ensure compliance with electrical safety standards. Maximum Video Coaxial Cable Length (feet/meters) Cable type RG-59 Wire gauge 23 AWG* 18 AWG* Maximum length (feet/meters) 750/229 RG-6 1500/457 RG-11 14 AWG* Electrical Specifications Input Voltage: 12 VDC/24 VAC Input Voltage Range: 11 to 16 VDC 17 to 28 VAC Power Consumption: 3.5 W (max) Mechanical Dimensions (W x H): 4.33” x 3.91” (110 mm x 96.3 mm) Weight: Net Shipping Construction: .66 lb (.3 Kg) 1.32 lb (.6 Kg) Housing and dome: Polycarbonate Environmental Emissions: FCC, CE (EN55022) Immunity: CE (EN50130-4) UL2044a, EU: 73/23/EEC LVD Safety: a Applies only to HD3VC4SHR and HD3VC4SA models. Honeywell Security Australia Pty Ltd. Unit 5, Riverside Centre, 24-28 River Road West Parramatta, NSW 2150, Australia www.ademco.com.au ℡ +61.2.8837.9300 Honeywell Security Asia Pacific 33/F Tower A, City Center, 100 Zun Yi Road Shanghai 200051, China www.security.honeywell.com/cn ℡ +86 21.2527.4568 Honeywell Security Asia Flat A, 16/F, CDW Building, 388 Castle Peak Road Tsuen Wan, N.T., Hong Kong www.security.honeywell.com/hk ℡ +852.2405.2323 Honeywell Security France Parc Gutenberg, 8, Voie La Cardon 91120, Palaiseau, France www.honeywell.com/security/fr ℡ +33.01.64.53.80.40 Honeywell Security Italia SpA Via Treviso 2 / 4 31020 San Vendemiano Treviso, Italy www.honeywell.com/security/it ℡ +39.04.38.36.51 Honeywell Security Spain Mijancas 1. 3a Planta P.Ind. Las Mercedes 28022 Madrid, Spain www.security.honeywell.com/es ℡ +34.902.667.800 Honeywell Security Nederland Netwerk 121 1446 WV Purmerend, Netherlands www.SecurityHouse.nl ℡ +31.299.410.200 Honeywell Video Systems UK Ltd. Aston Fields Road, Whitehouse Ind Est Runcorn, Cheshire, WA7 3DL, UK www.honeywellvideo.com ℡ +0844.8000.235 Honeywell Security South Africa Unit 6 Galaxy Park, 17 Galaxy Avenue Linbro Park, P.O. Box 59904 2100 Kengray, Johannesburg, South Africa www.honeywell.co.za ℡ +27.11.574.2500 Honeywell Security Germany Johannes-Mauthe-Straße 14 D-72458 Albstadt, Germany www.honeywell.com/security/de ℡ +49.74 31.8 01.0 Honeywell Security Poland Chmielewskiego 22a, 70-028 Szczecin, Polska www.ultrak.pl ℡ +48.91.485.40.60 Honeywell Security Czech Republic Havránkova 33, Brno Dolní Heršpice, 619 00, Czech Republic www.olympo.cz ℡ +420.543.558.111 Honeywell Security Slovakia Republic Vajnorskà 142, 83104 Bratislava Slovakia www.olympo.sk ℡ +421.2.444.54.660 2000/610 * Copper clad steel core, 95% braided shield www.honeywellvideo.com +1.800.796.CCTV (North America only) HVSsupport@honeywell.com 900.0824 - 09/06 - Rev 1.01 © 2006 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Extract, Print high-res Page Mode : UseOutlines XMP Toolkit : 3.1-702 Producer : Acrobat Distiller 7.0.5 (Windows) Keywords : HD3VC4SHR; HD3VC4SA; HD3VC4SHRX; HD3VC4SAX Create Date : 2006:04:26 15:09:30Z Creator Tool : FrameMaker 7.1 Modify Date : 2006:09:20 15:21:24-07:00 Metadata Date : 2006:09:20 15:21:24-07:00 Format : application/pdf Title : HD3VC4 3 Inch Dome Camera Quick Install Guide Creator : Honeywell International Inc. Subject : HD3VC4SHR, HD3VC4SA, HD3VC4SHRX, HD3VC4SAX Document ID : uuid:c714fd08-dee0-4a66-8290-7203a9f3e61b Instance ID : uuid:e8ecab5c-4b85-43a9-b4af-3c8f56e34a84 Page Count : 2 Page Layout : OneColumn Author : Honeywell International Inc.EXIF Metadata provided by EXIF.tools