Honeywell Home Security System 5804Bdv Users Manual K3636V3_RevA_ug

5804bdv-honeywell-tw.. 5804bdv-honeywell-two-way-wireless-keyfob-with-voice-user-guide

5804BDVUserGuide 5804BDVUserGuide

5804BDV Two Way Wireless Key with Voice Status User Manual 5804bdvUM Honeywell | Home Security Manuals

5804bdv f485ed5c-06f0-48a9-89f0-20d84245f65e Honeywell Home Security System 5804BDV User Guide |

: Honeywell Honeywell-Honeywell-Home-Security-System-5804Bdv-Users-Manual-261502 honeywell-honeywell-home-security-system-5804bdv-users-manual-261502 honeywell pdf

Open the PDF directly: View PDF .
Page Count: 2

K3636V3 9/04 Rev. A

ADEMCO 5804BDV

TWO-WAY WIRELESS KEY with VOICE STATUS

USER GUIDE

About the 5804BDV

The 5804BDV is a four-button remote control for your alarm system. It can send a command to the alarm system, such as to arm or disarm,

as well as receive system status. Two LEDs and a speaker indicate system status. The 5804BDV is typically used for arming, disarming, and

home automation. Check with your installer to understand which functions the buttons have been assigned on your unit.

Operating the Buttons

Activating a Function

To activate a function, press and hold the appropriate button down until the yellow LED flashes, and then release it.

Requesting System Status

You can check system status before arming or disarming your system.

Check your system status by momentarily pressing and releasing any button. The yellow LED will flash after you release the button. After a

second or two, the 5804BDV will display the system status through the LEDs and speaker (see the System Status Indications Table, below).

If the 5804BDV does not receive system status from the panel for approximately 5 seconds, it will shut itself down. It will also shut itself down

if you do not press a button within 5 seconds of receiving a status update.

System Status Indications Table

LED LED Condition Speech System Status

System Armed Away Armed Away or Maximum On Steady

System Armed Stay Armed Stay or Instant

Fire Fire Zone (Faulted Zone) Fire Alarm in progress

Alarm Alarm Zone (Faulted Zone) Armed, Burglary Alarm in progress

Red

Flashing

Alarm Alarm Zone (Faulted Zone) Alarm Memory

On Steady System Disarmed Ready To Arm Disarmed, Ready to Arm Green

Flashing System Disarmed Not Ready To Arm System Not Ready, Zones Faulted

Yellow (right) Flashing — Indicates RF transmission

In Enter House ID Mode Red & Green Alternately

Flashing

—

In Set Volume Level Mode

System AC Loss AC Loss Condition NA NA

Low Battery Low Battery Condition

Multiple Button Operations

5804BDV-005-V0

A + C Button Pair B + D Button Pair

Adjusting the Volume Level

To enter the Volume Level mode, press and hold down the A, B, and D buttons at the same time until the unit’s red and green LEDs flash

alternately. If no button is pressed within 5 seconds, the unit will automatically shut down and no change to the volume level is made. Press

the A button for low volume level, the B button for mid volume level, and the C button for maximum volume level. You will hear the word

“Alarm” at the selected volume. Then press the D button to accept the selected sound level. Note that volume level affects the life of the

battery. Use low volume for maximum battery life.

WARNING!

The 5804BDV should not be used

for silent panic operation.

The 5804BDV can generate the same responses as keypad panic

key pairs of [*] + [#] and [*] + [1] by depressing “A” + “C” and “B” +

“D” button pairs, respectively. You must depress the button pair

for at least 2 seconds for the 5804BDV to recognize the button pair

command. These button pairs allow you to activate panic, fire,

and medical alarms depending on control panel programming.

Low Battery Indication

When the unit goes into a Low Battery condition, the yellow LED will not flash when a button is pressed. Change both batteries immediately.

To Replace the Batteries

Removing or Inserting the Unit from a Belt Clip

5404BDV-002-V0

LIMITATIONS STATEMENT

Signals sent by wireless transmitters may be blocked or reflected by metal objects before they reach the alarm receiver. Even if the

signal path has been recently checked during a weekly test, blockage can occur if a metal object somehow blocks the signal path.

Wireless button type transmitters that have visual and audible indications of status must be used to confirm that the desired action

(such as arming) has occurred after pressing a function button on any of these transmitters. Be sure to listen for appropriate

audible and visual indications that such action has occurred. Otherwise, you could inadvertently leave yourself or your premises

unprotected.

External factors such as humidity, high or low temperatures, or constant activation of a programmed button may reduce battery life

in a given installation. If the button unit is used infrequently, activate it regularly (once per week) to confirm operation. A button

type transmitter will report a low battery condition to the alarm control when a low battery status is detected.

165 Eileen Way, Syosset, New York 11791

Copyright © 2004 Honeywell International Inc.

www.honeywell.com/security

ÊK3636V3fŠ

K3636V3 9/04 Rev. A

1. Remove the screw from the back case.

2. Remove case back by using the blade of a small screwdriver to pry open.

3. Place batteries as shown on diagram. Use CR2430 or DL2430Lithium batteries only.

4. Close the case by snapping case front and back together.

5. Replace the screw to secure the case.

WARNING!

Improperly installing the batteries will cause damage

to the batteries.