Honeywell Thermostat Rth230B Users Manual 69 1800 Programmable Electronic Installation And User Guide

RTH230B to the manual 958cfed3-0cde-47b5-a5e4-aef0ed07839d

: Honeywell Honeywell-Honeywell-Thermostat-Rth230B-Users-Manual-262173 honeywell-honeywell-thermostat-rth230b-users-manual-262173 honeywell pdf

Open the PDF directly: View PDF .
Page Count: 4

RTH230B 69-1800-01 11/09 1/4

The RTH230B programmable thermostat can be used to control:

• a gas, fuel oil or electric furnace - 2 or 3 wires

• a central air conditioner - 2 or 3 wires

• a hot water system with or without pump - 2 wires

• a millivolt system - 2 wires

• a central heating and cooling system - 4 or 5 wires

Note: These thermostats are not compatible with heat pumps or

multi-stage systems.

Features

• System operating mode selection: heat, cool or off

• Fan operating mode selection: automatic or on (continuous)

• Programmable heating and cooling cycle lengths: 10, 12, 15, 20

or 30 minutes

• Temperature display in °F or °C

• Battery replacement indicator

• 5-2 programming including:

- Preprogrammed energy-saving schedule

- Early Start

- Temporary bypass

- Time display (12 h or 24 h)

• Filter replacement indicator

2.1 Removing the Old Thermostat

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT

POWER TO THE HEATING SYSTEM.

nRemove the old thermostat to access the wires.

Warning: If the old thermostat was mounted onto an electrical box,

it was probably powered by 120/240 volts. In this case, this thermo-

stat cannot be used.

oIdentify and label each wire (with the corresponding letter on

the wire terminal) and remove them from the terminals.

pIf necessary, strip the end of each wire (maximum of 1/4 inch).

qWrap the wires around a pencil to prevent

them from falling into the wall.

rIf the hole in the wall is too big, insulate it

using a non-flammable material in order to

avoid air draughts behind the thermostat.

2.2 Installing the New Baseplate

For a new installation, choose a location approximately 5 feet

(1.5 m) above the floor and on an inside wall. Avoid draughty

areas (top of staircase, air outlet, etc.), dead air spots (behind

doors), direct sunlight or areas near concealed pipes or chim-

neys.

nRemove the thermostat faceplate.

oLoosen the locking screw to separate the thermostat from its

baseplate (the screw cannot be completely removed).

pTilt the thermostat upwards.

qMark and bore the appropriate mounting holes (or use the

existing holes). Insert the plastic anchors.

rPass the wires through the opening of the baseplate and fix the

baseplate to the wall using the screws provided.

2.3 Connecting the Thermostat

The connection of the new thermostat should be similar to that of

the old thermostat; however, it can vary depending on the installa-

tion.

Note: The red jumper wire between the Rc and Rh terminals must

be removed in 2- or 5-wire installations. The jumper must be used in

3- or 4-wire installations if you wish to use the mode selector switch

for the fan.

1. Introduction

2. Installation

RTH230B

Programmable Electronic Thermostat

Installation and User Guide

Display Adjustment

buttons

System operating

mode selector Fan operating

mode selector

Programming

buttons

Rh Heating power supply

Rc Cooling power supply

W Heating signal

Y Cooling signal

GFan

69-1800-01

RTH230B 69-1800-01 11/09 2/4

2.3.1 2-wire Heating

2.3.2 2-wire Cooling

2.3.3 3-wire Heating

2.3.4 3-wire Cooling

2.3.5 4-wire Heating and Cooling

2.3.6 5-wire Heating and Cooling

2.4 Setting J2 Jumper

The jumper defines the fan operation when the fan is placed in auto-

matic mode.

2.5 Installing the Batteries

nPull out the battery cover.

oInstall the batteries as shown. Observe the polarity.

pReinstall the battery cover. You will hear a clicking sound.

After the batteries are installed, the thermostat performs a series of

tests for approximately 5 seconds.

Afterwards, the screen displays the actual

temperature. It is normal that the displayed

temperature be higher than the ambient

temperature if you are holding the thermo-

stat. The thermostat will display the ambient temperature once it is

installed on the wall. By default, the setpoint is 70°F (21°C).

2.6 Completing the Installation

nOnce the baseplate and the batteries are installed, mount the

thermostat on the baseplate.

oSecure the thermostat using the locking screw and install the

faceplate.

pApply power back to the system.

3.1 System Operating Mode

Use the selector switch to place the system in Heating

mode (HEAT) or Cooling mode (COOL), or to set the

system off.

Note: When you place the thermostat in Cooling mode, you might need to

wait up to five minutes before cooling can start. This is a safety feature for

the compressor. will flash on the screen until cooling can start again.

Heat relay

Cool relay

Fan relay

Heat relay

Cool relay

Fan relay

Heat relay

Cool relay

Fan relay

Fan relay

Cool relay

Heat relay

HE

Use this setting if you have an electric furnace. In

this setting, when the fan is placed in automatic

mode, it works only when heating or cooling is

activated.

HG

Use this setting if you have a gas or fuel oil fur-

nace. In this setting, when the fan is placed in

automatic mode, it works as follows:

• When the thermostat is placed in cool mode,

the fan works only when cooling is activated.

• When the thermostat is placed in heat mode,

the fan is controlled by the furnace fan control

circuitry.

3. Basic Functions

J2 jumper

RTH230B 69-1800-01 11/09 3/4

3.2 Fan Operating Mode

Use the selector switch to set the fan to automatic

mode (AUTO) or continuous mode (ON).

Note: This switch is not used if you have a 2-wire

installation as the fan is not connected to the thermo-

stat.

3.3 Displaying the Temperature

The actual temperature is normally displayed. To view the setpoint,

press once on one of the buttons. The setpoint is displayed for

5 seconds along with the icon.

Note: Pressing either of the buttons more than once will

change the setpoint.

3.4 Setting the Temperature

Press one of the buttons until the desired temperature is dis-

played.

3.5 Thermostat Control Mode

3.5.1 Manual/Permanent Hold Mode

Maintains the temperature at a fixed setpoint. To place the thermo-

stat in this mode, press [ Mode ]. The house icon will disappear.

3.5.2 Programmable Mode

Maintains the temperature according to the energy-saving sched-

ule. To place the thermostat in this mode, press [ Mode ]. The cur-

rent period will be displayed. The four possible periods are:

To see the default settings of each period, see section 5.2.

Temporary Bypass

If you modify the temperature (using the buttons) when the

thermostat is in programmable mode, the new temperature will be

used for the next 2 hours. The house icon flashes during the

bypass. At the end of the bypass period, the thermostat returns to

the temperature settings of the period currently underway.

3.6 Filter Replacement Indicator

After 500 hours of operation, an icon appears to indi-

cate that the filter needs replacement. Once the filter

is replaced, press [Filter] for 3 seconds to remove

the icon and reset the counter.

3.7 Battery Replacement Indicator

An icon appears when the batteries need replacement.

This icon will flash for 120 days, then the thermostat

will cut power to the heating/cooling unit. The icon dis-

appears once the batteries are replaced.

After replacing the batteries, readjust the time and day (see section

5.1). However, the temperature and program settings are saved and

do not need to be re-entered.

Warning: Before removing the batteries, place the

system switch on the thermostat to Off. Otherwise, the

heating/cooling unit might still be running even after

the batteries are removed.

nTo access the configuration menu, press both buttons

simultaneously for 3 seconds.

oTo go to the next parameter (menu item), briefly press both

buttons simultaneously.

pTo modify a parameter, press one of the buttons.

qRepeat steps 2 and 3 if necessary.

rPress both buttons simultaneously for 3 seconds to exit

the configuration menu.

5.1 Setting the Time and Day

nPress [ Clk ]. The hour flashes.

oSet the hour using .

pPress [ Clk ]. The minutes flash.

qSet the minutes using .

rPress [ Clk ]. The day flashes.

sSet the day using .

tPress [ Exit ] to exit.

AUTO

• If you have an electric furnace (see section 2.4), the fan

works only when heating or cooling is activated.

• If you have a gas or fuel oil furnace (see section 2.4), the fan

works as follows:

• When the thermostat is placed in cool mode, the fan

works only when cooling is activated.

• When the thermostat is placed in heat mode, the fan is

controlled by the furnace fan control circuitry.

ON The fan is always on.

Wake up Leave for work Return home Sleep

4. Configuration Menu

DISPLAY DESCRIPTION DEFAULT OPTIONS

Temperature display °F °C or °F

Time display 12 h 12 h or 24 h

Early Start 1Off On or Off

Heating cycles per hour 242, 3, 4, 5 or 6 3

Cooling cycles per hour 242, 3, 4, 5 or 6 4

1 When Early Start is On, the thermostat determines when to start heating

or cooling so that the desired temperature is reached at the set time.

2 When either the heating or cooling parameter is displayed, use the sys-

tem mode selector switch to alternate between the two parameters.

3 For optimal heating control, use the setting that matches your system as

follows: 2=30 min (steam, gravity), 3=20 min (hot water, 90%+ high-effi-

ciency furnace), 4=15 min (gas or oil), 5=12 min (alternate setting for gas

or oil), 6=10 min (electric).

4 The corresponding cooling cycle lengths are as follows: 2=30 min,

3=20 min, 4=15 min, 5=12 min, 6=10 min

5. Programming

RTH230B 69-1800-01 11/09 4/4

5.2 Energy-saving Schedule

Your thermostat is preprogrammed with an energy-saving schedule.

The schedule automatically controls your heating or cooling system

by switching from one setpoint to the next according to the preset

times.

Note: To use the schedule, place the thermostat in programmable

mode.

5.3 Modifying the Schedule

You can program up to 4 periods per day, each period having its

own temperature settings. The same program is repeated daily from

Monday through Friday and another program is used for Saturday

and Sunday. For each period, you can set the start time, the heating

setpoint and the cooling setpoint.

nPress [ Pgm ]. The settings for period 1 are displayed.

Note: During programming, to skip a period, press [ CLR ] while

the period is displayed. For example, in the predefined energy-sav-

ing schedule, periods 2 and 3 have been skipped for Saturday and

Sunday.

oSelect the program using the [ Day ] button (MO TU WE TH FR

appears when the Monday-Friday program is selected or SA

SU appears when the Saturday/Sunday program is selected).

Press for 3 seconds to select all 7 days.

pSet the time (in increments of 15 minutes) using the but-

tons.

qPress [ P# ]. The heating or cooling setpoint

flashes depending on the position of the Heat/

Cool selector.

rSet the desired temperature for the displayed

period using the buttons.

sUse the Heat/Cool selector to switch to the other mode (e.g., if

you were in Heating mode, switch to Cooling mode). The set-

point for that mode flashes.

tSet the desired temperature using the buttons.

uPress [ P# ] to go to the next period.

vRepeat steps 2 to 8 for each of the remaining periods.

wPress [ Exit ] to exit.

Note: To use the schedule, place the thermostat in programmable

mode.

Power supply: 2 AA batteries

Maximum load: 1 A @ 24 Vca per output

Setpoint range (heating): 41 to 82°F (5 to 28°C)

Setpoint range (cooling): 59 to 95°F (15 to 35°C)

Display range: 23 to 122°F (-5 to 50°C)

Storage temperature: -2 to 122°F (-20 to 50°C)

Temperature display resolution: 1°F (0.5°C)

Accuracy: ± 1°F (0.5°C)

Heating/cooling cycle lengths: 10, 12, 15, 20 or 30 minutes (programmable)

Compressor short-cycle protection (minimum off time): 5 minutes

Data memory: non-volatile

Dimensions: 5 in. x 3 in. x 1 in. (127 mm x 75 mm x 28 mm)

Honeywell warrants this product, excluding battery, to be free from defects in

the workmanship or materials, under normal use and service, for a period of

one (1) year from the date of purchase by the consumer. If at any time dur-

ing the warranty period the product is determined to be defective or malfunc-

tions, Honeywell shall repair or replace it (at Honeywell's option).

If the product is defective,

(i) return it, with a bill of sale or other dated proof of purchase, to the place

from which you purchased it, or

(ii) call Honeywell Customer Care at 1-800-468-1502. Customer Care will

make the determination whether the product should be returned to the

following address: Honeywell Return Goods, Dock 4 MN10-3860,

1885 Douglas Dr N, Golden Valley, MN 55422, or whether a replace-

ment product can be sent to you.

This warranty does not cover removal or reinstallation costs. This warranty

shall not apply if it is shown by Honeywell that the defect or malfunction was

caused by damage which occurred while the product was in the possession

of a consumer.

Honeywell's sole responsibility shall be to repair or replace the product

within the terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR

ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL

OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDI-

RECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR

IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states do

not allow the exclusion or limitation of incidental or consequential damages,

so this limitation may not apply to you.

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL

MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WAR-

RANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE

ONE-YEAR DURATION OF THIS WARRANTY. Some states do not allow

limitations on how long an implied warranty lasts, so the above limitation

may not apply to you.

This warranty gives you specific legal rights, and you may have other rights

which vary from state to state.

If you have any questions concerning this warranty, please write Honeywell

Customer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-

800-468-1502. In Canada, write Retail Products ON15-02H, Honeywell Lim-

ited/Honeywell Limitée, 35 Dynamic Drive, Scarborough, Ontario M1V4Z9.

If you have any questions about the operation of your thermostat, please go

to www.honeywell.com/yourhome, or call Honeywell Customer Care toll-

free at 1-800-468-1502.

Default schedule settings Monday

to Friday

Saturday

& Sunday

Heating 70°F (21°C)

6:00 a.m. 6:00 a.m.

Cooling 78°F (25.5°C)

Heating 62°F (16.5°C)

8:00 a.m. --

Cooling 85°F (29.5°C)

Heating 70°F (21°C)

6:00 p.m. --

Cooling 78°F (25.5°C)

Heating 62°F (16.5°C)

10:00 p.m. 10:00 p.m.

Cooling 82°F (28°C)

Period start time

Program days

Period number

Temperature

setting

6. Technical Specifications

7. Warranty

8. Customer Assistance

As an ENERGY STAR® partner, Honeywell has determined that this

product meets the ENERGY STAR guidelines for energy efficiency.

Printed in USA