Hoover H3010 User Manual Manuals And Guides L0522802
HOOVER Vacuum, Upright Manual L0522802 HOOVER Vacuum, Upright Owner's Manual, HOOVER Vacuum, Upright installation guides
User Manual: Hoover H3010 H3010 HOOVER HOOVER - Manuals and Guides View the owners manual for your HOOVER HOOVER #H3010. Home:Vacuums & Floor Care Parts:Hoover Parts:Hoover HOOVER Manual
Open the PDF directly: View PDF 
.
Page Count: 14
| Download | |
| Open PDF In Browser | View PDF |
HOOVER
OwneF_s
English
e pp, 1.13
Espa_ol ,,_ pag. 15-22
Fran_ais ,,_ p. 24-31
!TM
m
Manua|
m
This cleaner inspected and packaged carefully before being shipped
from the factory. If you should happen to need assistance during
assembly or operation:
Visit us online at _,¢ww.hoover.com to find the service
outlet nearest you (click on the "Service" button) or
Catl 1-800-944-9200 for an automated referral of authorized
service outlet locations (U.S. only) or
Call 1-330-499o9499 to speak with a representative
Consumer Response Center.
PLEASE
DO NOT RETURN
THiS
PRODUCT
in our
TO THE STORE.
J
Review
this manua|
before
operating
c|eaner.
wwwoh@@verocem
®
in and
retain
The mode( and serial number are located at the bottom of the back of the
cleaner body.
For your personal records, please enter the COMPLETE model and serial
number in the spaces provided and retain this information.
Your cleaner is model
and has seriam number
It is suggested that you attach your sales receipt to this owner's manual.
Verification of date of purchase may be required for warranty service of
your Hoover product.
lm
Assembly ..................................... 3-4
Cleaner descriptions .................. 5
How to use ................................... 5-8
Automatic shut-off ..................... 7
General operation ...................... 6
Clean solution tank ................. 6-7
Recovery tank .......................................
7
Sto rag e ...................................... 11
How to clean .............................. 9-10
Recommended cleaning
sequence ..................................... 9
To clean floor .............................. 9
Cleaning sealed wood floors ..10
Picking up spills
....................... 10
(fYou Have a Problem ................. 12
Service ....................................... 12
important Safeguards .................... 2
Maintenance ............................ 10-11
Cleaning the brushes ......... 10-11
Cleaning the nozzle .................. 11
Warranty ........................................ 13
© 2001 The Hoover
www,hoover.com
Company
When using an electrical appliance, always follow basic precautions,
including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
m
arnung •
m To reduce
•
•
the
risk
of fire,
electNc
shock,
or injury:
•
Use indoors
only.
Use only on surfaces
moistened
immerse
product.
For use on bare floors
or seared
•
Always
•
Close supervision
is necessary
when any appliance
is used
Do not allow cleaner
to be used as a toy or to run unattended
by or near children.
at any time.
Keep hair, loose cmothing,
and a)(moving
parts.
away
install
float
before
Do not pick up anything
or hot ashes.
by the
wood
any wet
fingers,
that
pick
feet
is burning
cleaning
floors.
process
Not for
or small
spills.
Do not
use on carpets.
up operation.
and
aH parts
or smoking,
of body
such
from
as cigarettes,
openings
matches,
Do not pick up or use flammable
or combustibme
materials
such as gasoline
or
fine wood sandings
or use in areas where present.
Avoid picking
up hard, sharp objects
with the cleaner.
They may damage
the
c)eaner.
Do not put any object into openings.
Do not use with any opening
bmocked; keep
free of dust, Hnt, hair, or anything
that may reduce
air flow.
Do not pull or carry by cord, use cord as a bandme, close door on cord or pull cord
around
sharp edges or corners.
Do not run appliance
over cord. Keep cord away
from heated
surfaces.
•
Always
•
•
Unp)ug
c)eaner when not in use. Turn off a[) controms before
unp[ugging.
Do not unplug
by pulling
on cord. To unplug,
grasp the plug, not the cord.
handle
plug or appliance
with wet hands.
Connect
to a propedy
grounded
outlet only. See "Grounding
instructions".
Do not clean over floor electrical
outlets.
•
•
disconnect
cord
from
electrical
outlet
before
servicing
the cleaner.
Never
•
•
•
Do not use without
tanks in pmace.
Use extra care when cleaning
on stairs. Do not place cJeaner on stairs.
The use of an extension
cord is not recommended,
ff an extension
cord is
absomutely
necessary,
use at Beast a 18 gauge 3°wire cord which has a 3oprong
grounding
type plug and a 3°pole receptacle
that accepts
the machine
plug.
•
•
Keep detergents
and other cleaners
out of children's
Do not pick up ch[orine
b)each,
pine based c(eaners,
any other toxic
material
with this appliance.
•
When using
ventilated.
•
Fom[ow manufacturer's
instructions
not exceed recommended
mixing
•
Store
•
Do not use with damaged
cord or plug. If appmiance
is not working
as it should,
has been dropped,
damaged,
[eft outdoors,
or dropped
into water, take it to a
Hoover
Factory
Service
Center or Authorized
Hoover Warranty
Service
Dealer
(Depot).
•
Use cleaner
in a dry
Save
recommended
place.
only
for
Do not
chemicals
these
machine,
for aml chemicals
ratios.
expose
its intended
w(th this
machine
reach.
drain cleaner,
used
to freezing
use as described
be certain
in the
with
this
or
area
is we[(
machine.
temperatures.
instructions.
Do
Questions
er Concerns?
The Hoover Company wants to quickly resolve any concerns about your cleaner or questions regarding
its
use. Look on the list provided with the product for your local Hoover
Factory Service
Center or in the Yel=
low Pages under "Vacuum Cleaners = Household"
for the nearest Authorized
Hoover Warranty
Service
Deamer (Depot) or call:
Visit us online
button) OR
at www.hoover.com
Call 1-800-944-9200
Call 1=330=499=9499
to find the service
nearest
you (click on the "Service"
for an automated
referral of authorized service outlet locations (U.S. only) OR
to speak with a representative
in the Hoover Consumer
Response Center.
Call 1-800-228-4722
for questions or comments
ENGLISH®
Floor Cleaning Concentrate.
Greunding
outlet
concerning
Machine
Formula
LYSOL®
or OLD
|nstructiens
m
This appliance must be grounded. If it
should malfunction or breakdown, grounding provides a path of least resistance for
electrical current to reduce the risk of
electric shock. This appliance is equipped
with a cord having an equipment=ground=
ing conductor (C) and grounding plug (A).
The plug must be plugged into an appropriate outlet (B) that is properly installed
and grounded in accordance with all local
codes and ordinances.
Improper connection of the equipmentgrounding conductor can result in the risk
of electric shock. Check with a qualified
electrician or service person if you are in
doubt as to whether the outlet is properly
grounded. Do not modify the plug provided with the appliance - if it will not fit the
outlet, have a proper outlet installed by a
qualified electrician. This appliance is for
use on a nominal 120 volt circuit and has
a grounding plug that looks like the plug
illustrated in sketch (A).
A temporary adapter (D) may be used to
connect this plug to a 2-pole receptacle
(E) if a properly grounded outlet is not
available. The temporary adapter should
be used only until a properly grounded
outlet (B) can be installed by a qualified
electrician. The green colored rigid ear,
lug, or the like (F) extending from the
adapter must be connected to a permanent ground (G) such as a properly
grounded outlet box cover. Whenever the
adapter is used, it must be held in place
by a metal screw. NOTE: In Canada, the
use of a temporary adapter is not permitted by the Canadian Electrical Code.
Assemble
handle
C
A
F
AssembJe
Handme
Press down on latch (A) and remove
clean solution tank from upper handle,
B
Carton
A.
B.
C.
D.
E.
F.
contents
Hard floor cleaner
Upper handle
Screw packet (3 screws-l with washer)
Brush bmock
Nozzle
Fioor cleaning concentrates
The assembled
cleaner
will
look like this drawing.
This cleaner is intended for
househomd use.
Continued
--_
Withcordhook(B)to backofcleaner, Inserttwoscrewsintobackof handle
pushupperhandledownontocleaner. asshown.Tightenwitha Phillips
Insertscrewwithwasherinfrontof
screwdriver.
tankarea. Tightenscrewwitha
Phillipsscrewdriver.
Pushbrushcontrolswitch(C)downto
connectswitchrod.Youwill heara
"click"whentheswitchrodis in
place.
f
/
i
Liiili
i
Replace clean solution tank by positioning bottom first. Press latch and
snap top portion into place.
To install brushes, place handle in
upright position. Tilt cleaner back so
that it rests on the floor.
Align post (D) on brush block with
hole (E) on bottom of cleaner. Turn
brushes slightly until post fits easily
into hole.
Press brush assembly firmly to snap
into place.
To install nozzle, make sure latches
(F) are out.
Align middle section (G) of nozzle
with opening (H) on cleaner.
Remove cardboard packing insert
from squeegee area on underside of
nozzle.
While holding nozzle in place, slide
latches inward to lock in place.
Cord
dip
To help keep the cord out of the way
while cleaning, position cord down
into cord clip (I), located on the
handle.
1
2
4
18
17
14
17
12
13
15
The assembled cleaner will look like
this drawing,
1. Hand grip
2. Solution trigger:
squeeze to
release clean solution,
3. Brush control switch: Turns
brushes ON for wet cleaning and
OFF for wet pickup and dry vacuuming,
4. Clean solution tank release
5. Clean solution tank cap/
measuring cup
6. Clean solution tank
7. ON/OFF switch
8. Recovery tank lid and filter
9. Recovery tank release
10. Recovery tank: Collects dry
debris as well as dirty cleaning
solution,
11. Wet/Dry pedam: Press pedal to
change between wet and dry
cleaning,
12. WettDry indBcators: Shows
either wet or dry cleaning usage,
13. NozzJe release buttons:
Release nozzle for easy clean-up,
14. Brush remease buttons:
Remove
brushes for easy clean-up,
15. Nozzle
16. Squeegee
17. Handle release peda_
18. Cord hooks: Top hook rotates
for quick cord release,
19. Carrying handle
20. Soft4read wheels
This cleaner is intended
hold use.
ON/OFF
To transport
for house-
Operate cleaner only at voltage
specified on data plate on back of
cleaner,
Plug cleaner into a properly
grounded outlet.
A
Handle
Remease Peda_
Step on pedal (A) to lower handle to
operating position, Handle does not
lock into a single position but "floats"
to allow convenient operation,
Switch
Push switch (B) up to turn cleaner on,
Push switch down to turn cleaner off,
To move your cleaner from room to
room, put handle in upright position;
tilt cleaner back on rear wheels and
push forward,
Condnued
-4_
5
General
Operation
Your HOOVER FloorMate
TM
Cleaner
can be used to both vacuum dry
debris and wet clean non-carpeted
floor surfaces such as vinyl, tile and
sealed wood, It is not intended for
D
use on carpet or rugs.
Thecleanermayalsobe liftedusing
thecarryinghandle(C)onthe backof
thecleaner,
CAUTION: To prevent damage to
wood floors, follow the flooring
manufacturer's
cleaning recommendations.
If using cleaner on sealed wood
floors, inspect floor surface for
worn finish, bare wood or separated joints. Do not use 'FloorMate'
Cleaner to wet clean sealed wood
floors if any of these conditions
exist.
WetlDry
pedal and indicators
The wet/dry pedal (D) lowers the nozzle squeegee for wet operation and
raises it for picking up dry debris,
The WET indicator (E) will show red
when pedal is set for wet operation,
The DRY indicator (F) will show red
when pedal is set for dry vacuuming,
See "How to clean" section for complete cleaner setup instructions,
Step on pedal to choose either the
WET or DRY setting,
To wet clean with brushes turned
on, push the switch down to the
WET SCRUB position,
For wet pickup, push the switch up
to the WET/DRY PICKUP position, In
this position, the brushes will not
rotate and are raised off the floor surface,
G
Brush
Contro_
Switch
The brush control switch (G) turns the
brushes on and off,
The
For dry debris pickup, push the
switch up to the WET/DRY PICKUP
position,
See "How to clean" section for complete cleaner setup instructions,
Tanks
C_ean Solution
Tank)
Tank (Upper
The clean solution tank holds the
cleaning solution that is to be dispersed onto the surface to be
cleaned,
How to fiJJ
Disconnect
outlet.
cleaner from electrical
Place cleaner handle in upright,
locked position,
To remove tank, press down on
release button and pivot tank forward,
Carry tank to a sink,
Rotate tank cap counter-clockwise
and lift up to remove cap,
m
,
,
2.0 ozJ60mL
Use Machine Formula OLD ENGLISH@ Wood Floor Cleaning Concentrate for wood floors when cleaning
laminate wood, polyurethane sealed
wood or other wood floors that can
normally be cleaned using water.
Check for worn spots or joint separations before using, as these conditions could lead to damaged flooring
when using water to clean floor.
.m
Both of these concentrates
Turn cap (H) upside down to serve
as a measuring cup.
Using cap, measure 2 oz. of applicable concentrate formulated for use
with the 'F!oorMate' hard floor cleaner.
For best results, use Machine Formula
LYSOL@ Floor Cleaning Concentrate
when cleaning floor surfaces such as
vinyl, ceramic and other tiles, and
linoleum.
have been
specifically formulated to resist
excessive foaming and other undesirable effects when used in your 'FloorMate' Cleaner.
DO NOT use cleaning concentrates
that contain pine or solvent based
ingredients.
CAUTION: Machine FormuNa
LYSOL® Floor Cleaning Concentrate and OLD ENGUSH® Wood
Floor CleanEng Concentrate cannot
be used in Hoover SteamVac TM
products. Doing so could damage
your SteamVac TM.
Pour cleaning concentrate into tank.
Fill tank to fill line (I) (1 quart) with
warm water.
rubber ring (J) on cap has become
dislodged, reposition it with uneven
side against ledge (K) as shown.
Recovery
Tank (mower tank}
The recovery tank holds both dry
debris and dirty cleaning solution that
is picked up from the floor surface.
Automatic
Replace cap. Rotate cap clockwise
until it locks in place. Cap must be
locked in place for proper performance and to prevent leaking.
Position bottom of tank into cleaner.
Press latch and snap tank into place.
Shut-Off
An automatic suction shut-off is built
into the recovery tank to prevent the
tank from overflowing.
When the shut-off activates, the cleaner will not pick up debris and the
sound of the motor will change.
There are two reasons the shut-off will
activate.
1. Recovery tank is full =Turn the
cleaner off and empty the recovery
tank.
2. The handle was raised to the
upright position wMle the motor
was running - Turn cleaner off. Wait a
moment for the shut-off to reset. Turn
cleaner on and continue cleaning.
Cont_ued
_-_
7
How to Empty
\
Turn cleaner off and disconnect
from emectrical outlet.
Although not necessary for satisfactory performance, it is recommended
that the recovery tank be emptied
after dry vacuuming and before wet
operation.
Check the solution tank also. It may
need to be refilled at this time.
Dry or loose debris will also collect on
the filter screen (O) in the tank lid.
Remove debris from screen.
The filter screen may also be cleaned
by rinsing it under running water.
To remove tank, press down on
release button (L) and pivot tank forward.
Lift up on tank lid latch (M) and
remove the tank lid (N). Empty tank.
To replace lid, align tab (P) on lid with
hole on front of tank (Q).
To replace tank, insert bottom of tank
into cleaner and pivot top portion until
it is locked in place.
Snap latch over tabs (R) on back of
tank.
The tank lid contains a washable,
reusable filter. Clean this filter when
suction is low or reduced.
To Clean
Fi_ter
Turn cleaner OFF and disconnect
from eJectricam outlet.
Remove recovery tank and lid (Fig. 216 & 2-!7). Remove filter lid (S), then
remove filter. Remove loose debris
from filter by either brushing or tapping the filter. The filter may also be
rinsed for additional cleaning. Allow
filter to air dry between uses.
Replace filter lid. Press down firmly to
secure the seal.
Cleaning
Sequence
Use your HOOVER 'F!oorMate' Cleaner to:
1. Dry Vacuum to remove loose dirt, hair and debris.
2. Wet Clean the floor surface. The brushes will provide light agitation to help
loosen dirt.
3. Wet Pickup reduces drying time of the floor surface.
Follow the chart to set the controls for each cleaning step.
OPERATION
Dry Vacuuming
Wet Cleaning
Wet Pickup
BRUSH
CONTROL
SWmTCH
WET/DRY
"Wet/Dry Pickup" (UP)
PEDAL
Dry Pickup
"Wet Scrub" (DOWN)
Wet Pickup/
Scrub
"Wet/Dry Pickup" (UP)
Wet Pickup/
Scrub
See Page 6 Figs. 2-6 and 2-7 for complete instructions on the control switch
and pedal.
To Clean
lineleu_,
The cleaner's suction will pick up the
dirty solution throughout cleaning.
Fmeer {vinym, ti_e,
eteo}
1. Set cleaner for Dry Vacuuming
operation and vacuum floor. (See
chart on page 9.)
A
2. Empty Recovery Tank. (Figs. 2-16
through 2-20).
3. Fill solution tank with Machine Formula LYSOLO Floor Cleaning Concentrate and water, according to
instructions for Figs. 2-8 through 212. Do not use pine or solvent
based cleaning concentrates in
your cleaner. Do not use any type
of wax in your cleaner.
8. To greatly enhance dP/ing of the
floor surface, release trigger and
move wet control switch up to the
"WET/DRY PICKUP" setting. Continue to move cleaner over the area to
pick up the dirty solution.
9. To continue cleaning another area,
move wet control switch down to
6. Step on handle release pedal and
lower handle to operating position;
turn cleaner ON.
4. Set cleaner controls for "Wet
Cleaning" operation. (See chart on
page 9.)
7. To release solution, squeeze trigger (A). Slowly move cleaner forward
and backward over area to be
cleaned. Squeeze trigger to release
solution as needed.
5. Dry hands and plug cleaner into a
properly grounded outlet.
Overlap strokes by one inch to help
prevent streaking.
"WET Scrub".
Repeat with steps 7-9.
NOTE: When switching between wet
cleaning and wet pickup, it is not necessary to turn the cleaner off. Simply
move the control switch back and
forth between the two settings.
10. Empty recovery tank or clean the
filter when the motor sound becomes
higher in pitch and there is a loss of
suction (see "Automatic Shut-Off",
page 7).
Cleaning
Floors
$ea_ed
Wood
Your HOOVER _FloorMate' Cleaner
may be used to clean wood floors
that have been sealed with a
polyurethane coating and can be
cleaned with water.
CAUTION: To prevent damage to
wood floors, follow the flooring
manufacturer's
cleaning recommendations.
If using cleaner on sealed wood
floors, inspect floor surface for
worn finish, bare wood or separated joints. Do not use 'FIoorMate'
C_eaner to wet clean sea_ed wood
floors if any of these conditions
exist.
9. To greatly enhance drying of the
floor surface, release trigger and
move wet control switch to the "WET
PICKUP" setting.
10. To continue cleaning, move wet
control switch down to "WET Scrub".
Repeat steps 7 - 9. Make sure all
areas are completely dry. Ensure
that no water remains on the floor.
1. Inspect floor surface for worn finish, bare wood or separated ioints.
Do not use your 'FloorMate' Cleaner
to wet clean the floor if any of these
conditions exist.
2. Set cleaner for Dry Vacuuming
operation and vacuum floor (see chart
on Page 9).
3. Empty recovery tank (Figs. 2-16
through 2-20).
4. Fill solution tank with Machine Formula OLD ENGLISH® Wood Floor
Cleaning Concentrate and water,
according to instructions for Figs. 2-8
through 2-12.
7. Step on handle release pedal and
lower handle to operating position;
turn cleaner ON.
8. Push cleaner forward, squeeze
trigger while pulling cleaner backward. Release trigger and push
cleaner forward. Continue cleaning
floor surface while releasing solution
on the backward strokes only. This
will allow for effective cleaning with
small amounts of solution.
Overlap strokes by 1 inch to help prevent streaking.
11. Empty the recovery tank or clean
the filter when the motor sound
becomes higher in pitch and there is
a loss of suction (see "Automatic
Shut-Off", Page 7).
Picking
Lip Spills
Your cleaner may also be used to
pick up small liquid spills (1 quart
or less, never to exceed 114 inch in
depth} on non-carpeted floors.
Set Wet/Dry pedal in the WET Pickup/Scrub position.
Set Wet Control switch to the
"WET/DRY Pickup" position.
Do not use the cleaner to pick up
flammable or combustible
liquids
or chemicals. Do not use the cleaner to pick up detergents that contain pine or solvent based ingredients.
A
the
6. Dry hands and plug cleaner in to
a propeNy grounded outlet.
Do not use pine or solvent based
detergents. Do not put any type of
wax in your cteaner.
NOTE: When switching between wet
cleaning and wet pickup, it is not
necessary to turn the cleaner off.
Simply move the control switch back
and forth between the two settings.
Cleanincj
5. Set cleaner controls for "Wet"
Cleaning (see chart page 9).
-____
'_,_,!;_ii_ii,i,i!i!!i!!i_ii!_i_!i_!i_!i_!i_iiii!!iiii'i_i_iiiiiiii,_
_
brushes
Turn cleaner OFF and disconnect
from electrical outlet.
The brush assembly can be removed
for easy cleaning.
Push the two brush release buttons
(A) at the same time.
Tilt cleaner back slightly and remove
brush assembly (B).
The brushes can be washed with a
mild detergent and rinsed. Do not use
pine or solvent-based detergents.
10
Toreplacebrushes,firstremovesolu- Pressbrushassemblyfirmlyto snap
tiontank(Fig.2-8)andrecoverytank intoplace.
(Fig.2-!6). Settanksaside. Thiswill
preventpossibleleaking.
Withhandlein uprightposition,tilt
cleanerbackso thatit restsonthe
floor.
Alignpost(C)on brushblockwith
hole(D)on bottomofcleaner.Turn
brushesslightlyuntilpostfitseasily
intohole.
Cleaning
Slide the two nozzle release latches
(F) outward.
Remove nozzle (E) by pulling straight
out.
To replace nozzle, make sure latches
are out.
Rinse nozzle under running water.
Remove debris from squeegee (G)
and wipe with a damp cloth.
Align middle section (H) of nozzle
with opening (I) on cleaner.
the
Nozzle
Turn cleaner OFF and disconnect
from electrical out{et.
The cleaner's nozzle (E) can be
removed for easy cleaning.
Sterage
\
While holding nozzle in place, slide
latches inward to lock in place.
Before storing cleaner:
Turn cleaner OFF and disconnect
from electricaJ outJet.
,, Empty and rinse solution and recovery tanks. Allow to air dry.
o Allow filter in recovery tank lid to
dry.
o Set the cleaner for "Dry Vacuuming"
(pedal to "DRY" and Wet Control
switch up).
,, Make sure that nothing is pressing
on the nozzle squeegee.
o Do not store cleaner on a wood surface unless cleaner is compJetely
dry.
Continued
_
11
Service
If a minor problem occurs, it usually
can be solved quite easily when the
cause is found by using the check list
below.
Possible cause
Possible solution
Not firmly plugged in
. Plug unit in firm/}/.
, No voltage in wail plug
Check fuse or breaker.
. Blown fuse/tripped
breaker
. Replace fuse/reset breaker.
Possible cause
Possible solution
, Automatic shut-off activated
. Turn cleaner OFF and then ON
again or
Empty recovery tank (see "Automat/c shut-off" section)
, Filter or fitter lid missing or not
positioned correctly
. Ensure that filter and filter hd are
proper/}/positioned
in the recover}/
tank lid (Fig. 2-22)
, Recovery tank andtor solution
tank not positioned properly
. Ensure that both tanks are locked in
place.
, Fitter is dirty
. Clean filter
, Nozzle not properly positioned
. Ensure nozzle is replaced properly
and locked (Figs. 4-8 & 4-9).
Possible cause
Possible solution
Cleaner not set for wet operation
Press wet/dry pedal to "WET" posF
tion.
, Recovery tank not properly
installed
. Ensure that recovery tank is
installed proper/}/(Fig. 2-20).
Recovery tank full/automatic
shutoff engaged.
Remove and empty recover}/tank.
, Filter or filter lid missing or not
properly positioned.
. Ensure recovery tank filter and filter
lid are proper/}/installed
(Fig. 2-22).
PossibJe cause
Possible solution
. Cleaner not set for dry operation
. Press wet/dry pedal to "DRY PiCKUP" position.
, Debris is too large to cJear
squeegee
. Tip nozzle off floor by pushing dovvn
on handle.
Possible cause
Possible soludon
, Solution tank not firmly in place
. Make su;e tank is securely locked in
position.
, Solution tank empty
Refill solution tank.
To obtain approved HOOVER service and
genuine HOOVER parts, locate the nearest Hoover Factory Service Center or
Authorized
Hoover Warranty Service
Dealer (Depot) by:
'_checking the Yellow Pages
under "Vacuum Cleaners Household" OR , checking the list of Factory
Service Centers provided
with this cleaner OR , checking the Service section of The
Hoover Company on-line at
www.hoover.com
OR , calling 1°800°944°9200 for an auto
mated referral of authorized service
outlet locations (U.S. only).
Do not send your cleaner to The Hoover
Company in North Canton for service, this
will only result in delay.
If further assistance is needed, contact
The Hoover Company Consumer
Response Center, North Canton, Ohio
44720 Phone: 1-330-499-9499.
In Canada, contact Hoover Canada,
Burlington, Ontario L7R 4A8,
Phone: 1-800-263-6376.
Always identify your cleaner by the complete model number when requesting
information or ordering parts. (The model
number appears at the bottom of the back
of the cleaner body.)
For questions
or comments
Machine
Formula LYSOL@
concerning
or OLD
ENGMSH@
Floor Cleaning
cal! 1-800-228-4722.
Concentrate,
LYSOL@ and OLD ENGMSH@
are registered trademarks
of Reckitt Benckiser
Inc.
Possible cause
Possible so/udon
Excess cteaning concentrate
foaming in tanks
. Use Machine Formula LYSOL@
Floor Cleaning Concentrate or
Machine Formula OLD ENGLISH@
Wood Floor Cleaning Concentrate, it
is a low-foam formulation, if using
cleaning concentrate other than
L YSOL@ brand or OLD ENGLISH@
brand, remix cleaning soludon using
less concentrate.
, Solution tank not properly
installed
. Ensure that tank is installed proper/}/
(Fig. 2-15).
, Recovery tank is fult
. Empty tank
12
Possible cause
Possible solution
CJeaner set for "WET/DRY PiCKUP"
. Move wet control switch down to
"WET SCRUB" position (Fig. 2-7).
, Circuit breaker inside cleaner is
tripped
. To reset the breaker.
(1) Push the ON/OFF switch completely down. You will feel some
resistance when the switch moves
downward. The switch will also move
slightly upward on its own.
(2) Wait one minute.
(3) Repeat step 1.
(4) Turn the cleaner ON and continue
cleaning.
If the brushes continue to stall and
the breaker tr@s again, clean the
brushes to remove debris. (Figs. 4-1
through 4-4)
Fuji One Year
(Domestic
Use)
Your HOOVER@ appliance is warranted in
normal household use, in accordance with
the Owner's Manual against odginal
defects in material and workmanship for a
period of one full year from date of purchase. This warranty provides, at no cost
to you, all labor and parts to place this
appliance in correct operating condition
during the warranted period. This warranty applies when the appliance is purchased in the United States including its
territories and possessions, or in Canada
or from a U. S. Military Exchange. Appliances purchased elsewhere are covered
by a limited one year warranty which covers the cost of parts only. This warranty
does not apply if the appliance is used in
a commercial or rental application.
Warranty service can only be obtained by
presenting the appliance to one of the fop
lowing authorized warranty service outlets. Proof of purchase will be required
before service is rendered,
1. Hoover Factory Service Centers.
2. Hoover Authorized Warranty Service
Dealers (Depots),
For an automated referral of authorized
service outmets in the U.S.A.,
phone 1o800o944o9200 OF(
Visit 1"he Hoover Company
on°line at
www,hoover,com
This warranty does not cover pick up,
delivery, or house calls; however, if you
mail your appliance to a Hoover Factory
Service Center for warranty service, transportation will be paid one way.
While this warranty gives you specific
legal rights, you may also have other
rights which vary from state to state.
If further assistance is needed, or if there
are questions concerning this warranty or
the availability of warranty service outlets,
write or phone the Consumer Response
Center, The Hoover Company, 101 East
Maple St., North Canton, Ohio 44720.
Phone 1-330-49%9499.
In Canada, contact Hoover Canada,
Burlington, Ontario L7R 4A8,
1-800-263-6376.
13
14
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 14 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Thu Apr 05 01:20:13 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools