Hoover H3060 User Manual Manuals And Guides L0502276

HOOVER Power Steamer Manual L0502276 HOOVER Power Steamer Owner's Manual, HOOVER Power Steamer installation guides

User Manual: Hoover H3060 H3060 HOOVER HOOVER - Manuals and Guides View the owners manual for your HOOVER HOOVER #H3060. Home:Vacuums & Floor Care Parts:Hoover Parts:Hoover HOOVER Manual

Open the PDF directly: View PDF .
Page Count: 20

Download
Open PDF In Browser	View PDF

HOOVER
ate TM

SpinS

800

Floor Cleaner

www_h@overoco_

When using an electrical appliance, ahvays ibBow basic precautions.
including
the following:
READ ALL INSTRUCTIONS
BEFORE USING APPLIANCE.

_lb reduce

the risk

of fire. electric

shock, or injury:
, Use indoors only.
, Use only on surfaces moistened
by the cleaning process or small
spills. Do not immerse product.

• Connect to a p_roperlygrounded
outlet only. See ' Grounding
Instructio_ls'.
- Do not clean over floor electrical
outlets.

* For use on bare floors or seated
wood floors. NO_I ['or use on
carpets.

• Do not use witho_ _ tanks m
place.

* Always install float before
wet pick up operation.

° Use extra care -when cleaning
stairs. Do riot place cleaner on
stairs,

any

* Close supervision
is necessary
when any appliance is used by or
near chi|dren. Do no_ allow cleaner
to be used as a toy or to run unattended at any time.
, Keep hair, loose clothing, fingers,
feet and all parts of body away&ore
openings and moving parts.
, Do not pick up anything that is
burning or smoking, such as cigarettes, matches, or hot ashes.
* Do not pick up or use flammable
or combustible
materials such as
gasoline or fine wood sandings or
use in areas where they may Be presen[,

, The use of an extension cord is
riot recommended.
If an extension
cord is absolutely necessary, use at
least a t6 gauge 3-wire cordwhich
has a 3-prong grounding
type plug
and a 3-pole receptacle _at accepts
_he machine plug.
* Keep detergents and other cleaners out of children's
reach.
o Do uo_ pick up chlorine bleach,
drain cleaner, gasoline or any other
loxic material with this appliance.
* When using recommended
chemicals with this machine, be certain
area is well ventilated.

• Avoid picking up hard, sharp
objects with the cleaner. They may
damage the machine.

Follow manufacturer's
instructions for all chemicals used with
this machine. Do not exceed recommended mixing ratios.

, Do not pm any object into openings. Do not use with any opening
blocked; keep fl'ee of dust, lint, hair.
and anything that may reduce air
flow.

Store in a dry place. Do not expose machine to Freezing temperamres_

, Do not pull or carry by cord use
cord as a handle, close door on cord
or pull cord around sharp edges or
corners. Do not run apphance over
cord. Keep cord away from heated
surfaces.

, Do not use with damaged cord or
plug. If appliance is not working as
it should, has been dropped, damaged left outdoors, or dropped into
water, take it to a Hoover Factory
Service Center or Amhorized
Hoover Warranty Service Dealer.

* Always discormect cord _}orn electrieel oulle_ before servicing the cleaner,

* Use cleaner only for its intended
use as described in the instructions.

* Unplug cleaner when not in use.
Turn off all controls be[ore unplugging.
, Do not unplug by pulling on
cord. To unplug, grasp the plug, no_
_he cord.
, Never handle plug or appliance
with wet hands.

This product contains chemicals
known to the State of California to
cause cancer. WASH HANDS AFTER
HANDLING.

This appliance must be grounded. If it
shouM malfun(tion or breakdown,
grounding
provides a path of leas{ resis
tance for electrical current to reduce the
risk of electric shock This appliance is
equipped with a cord having an equip
men[-grounding

conductor

grounding plug (A). The plug must be
plugged into an appropriate outlet (B)
that is properly installed and grounded
in accordance with all local codes and
oT([illaIlces.

hnptoper connection of the equipment
grounding
conductoi can result in the
risk of electric shock. Check with a quali
fled ele(trician or service person if'you
are in c[oub{ as to whether the outlet is
properly grounded. Do not modify the
plug provided with the appliance - if it
will not fit the oudet, have a proper out
le_ installed by a qualified electrician.
This appliance is for use on a nominal
120 volt circuit and has a grounding
plug that looks like [he plug illus[ra[ed
in sketch (A).

A temporary
adapter (D) may be used _o
connect this plug to a 2 pole _eceptacle
(E) if'a properly grounded oudet is no{
available. The _emporary adapter should
be used only until a properly grounded
outlet (B) can be installed by a qualified
electrician. The green cobred rigid ear,
lug, or d_e like (F) ex_ending from _he
adapter mvst be connected to a perma
nent ground (G) such as a properly
grounded outlet box coven Whenever
the adapter is used, it must be helc[ in
place by a metal screw. NOTE: In
Canada, the use of' a temporary adapter
is not permitted by the Canadian
Electrical Code.

T0-7ontact

u--s:

- www.hoover.com
. 1-800-944-9200

- automated

Important
safeguards
........
Carton contents
.............
Cleaner description
..........

service

2
3
4

dealer locator
- 1-330-499-9499 - our Consumer
Response Center {8AM to 5 PM
Monday - Friday)

General Operation
Mode selector dial ..........
Solution tank ...........

f Fill in and Save

8
9-10

To clean filters .........
11-12
How to clean
Recommended
cleaning
sequence .................
12
Cleaning floors ...........
13
Picking up spills ..........
13
Using the hose and tools
Select tool ................
14
Attach hose and tool .......
14
Storage ....................
15
Maintenance
Cleaning the nozzle .......
16
Cleaning the brushes ......
17
Troubleshooting
............
18
Service ....................
19

For your records, enter the model number and
serial numbers in the spaces provided. These
numbers are located on the data label on the back
of the cleaner hod>
Model No.
Serial No.
Save your sales receipt and attach it to this
manual. Proof of date of purchase may be
required for warranty service of your cleaner.

Warranty

..................

,..

B.
C.
D.
E.
F.
G.
H.
L
].

Hard floor cleaner
Nozzle
Upper handle
Brush assemblies (2)
Tool caddy
Floor swivel tool
Grout tool
Telescoping wand
Hose
Floor cleaning
concentrates

,J
A

IU8
LISTED
© 2004 The Hoover Company
vw,w_.hoovef.oom

J
ContJnuect

f
This cleaner
is intended
household
use.

for

Operate cleaner only at voltage
specified on data plate on back
of cleaner, Plug cleaner into a
properly grounded outlet,

11j

1.
2.
3.

Soft hand grip
ON/OFF switch
Solution trigger: squeeze to release
cleaning solution
4. Mode selector dial: turns brushes
ON for wet cleaning and OFF for wet
pickup and dry vacuuming
5. Clean solution tank cap/measuring
cup
6. Clean solution tank
7. Clean solution tank release
8. Recovery tank release
9. Recovery tank lid and filter
10. Recovery tank: collects d W debris as
well as dirty cleaning solution
11. Nozzle release buttons: _>lease
nozzle for easy clean-up (located
behind nozzle)
12. Nozzle

13.
14.
15.
16.
17.
18.
19.
20,
21.
22.
23,
24,
25.
26.

Squeegee (underneath nozzle)
Bumper
Soft-tread wheels
Hose connector door
Carrying handle
Upper handle release button
Cord hooks: top hook rotates
for quick cord _>lease
Handle release pedal
Tool caddy
Hose
Telescoping wand
Grout brush assembly (gray
bristles)
Floor swivel tool
Grout tool

Assemble

handle

Rotate bottom
the upright
%lt.

Align
handle
aandle

handle
position

support
(A) up
until a snap is

control
rod (B) on upper
(C) with slot in bottom
support
(D).

Push upper
is snapped

handle
in place.

until

Install

brushes

To install brushes,
pright
position.
that it rests on the

and

nozzle

place handle
in
Tilt cleaner
back so
floor.

Align post (A) on brush
block with hole
(B) on bottom
of cleaner.
Turn brushes
slightly
until post fits easily into hole.

Continued

Press
place.

brush

% install

assembly

nozzle,

Align middle
section
(E) or] cleaner.
Remove
cardboard
area on underside

While

The

holding
inward

make

firmly

sure

to snap

latches

(D) of nozzle

packing
of nozzle.

insert

into

with

opening

from

squeegee

nozzle
in place,
to lock in place.

slide

two sections
(A & B) of the tool
y snap together
for assembly.

Press where
indicated
securely
in place.

by arrows

to snap

The caddy
conveniently
fits over the
of the cleaner
nozzle
(C) for storage.

top

Store hose;tools and accessories

To store bose: Place the hose grip (D) into
(E) on back of caddy. Pull hose up and
press into cut-out area (F). Continue wrapping hose down, underneath tongue (G), and
back tap, pressing into second cut-out area (H).
Place hose end (I) into slot (J) on back of caddy.
E

Place floor swivel tool (K), grout tool (L), brush
assembly (M), telescoping wand (N) and detergent (0) into caddy as shown.

Raise tapper handle (A) to upright
position until it locks in place.

Press tapper handle release button
'B) to fold handle to storage position.

Step on pedal (A) to lower handle
to operating position. Handle does
not lock into a single position, but
"floats" to allow convenient operation.
J

Push switch (A) once to turn cleaner
Push switch again to turn
cleaner OFF.

To move your cleaner from room to
room, put handle in upright
position, tilt cleaner back on rear wheels
and push forward.

The cleaner may also be lifted using the carying handle (A) on the ff'ont of the cleaner.

Your HOOVER
FloorMate
TM
SpinScrub
TM
800 Cleaner
can be used to both vacuum
dry debris
and wet clean non-carpeted
floor surfaces
such as vinyl, tile, marble
and sealed
wood.
It is
not intended
for use on carpet
or rugs.
CAUTION:

To prevent

damage

to wood

If using
cleaner
on sealed
wood
floors,
separated
joints.
Do not use FloorMate
floors
if any of these
conditions
exist.

The Mode selector
on and off.

For dry

floor

brushes
surface.

dial (A) turns

floors,

inspect
floor
SpinScrub

the brush-

debris
pickup,
turn the dial to the
position.
In this position,
the
will not rotate
and are raised
off the

To wet clean with
dial to the WASH
For wet pickup,
UP position.

brushes
position.
turn

the

Refer to "How
to clean"
cleaning
instructions.

turned

dial

section

ON,

to the

turn

WET

for complete

the

PICK-

the

flooring

manufacturer's

surface
for worn
Cleaner
to wet

finish,
clean

clean-

bare wood
sealed
wood

The tanks
Solution

(upper)

tank

The solution tank holds detergent
and water
dispersed
onto the surface being cleaned.

that is to be

How to fill
Disconnect
Place cleaner

cleaner

fl'om electrical

handle

in upright,

75 remove tank,
ht out.

Carry

squeeze

outlet.

locked
release

position.
button

and pulltank

tank to a sink.
Rotate
(A).

tank cap counter-clockwise

Turn cap (A) upside

down

to serve

and lift up to remove

as a measuring

cap

cup.

hard surface floors such as vinyl, linoleum, laminate
wood, polyurethane
sealed wood or other wood floors that can
normally be cleaned using water, use one cap (2 oz.) HOOVER')
Floor to Flooff MCleaner.
Check for worn spots or joint separations
before
conditions
could lead to damaged
flooring
when
clean floor.

using,
using

as these
water to

When cleaning
ceramic and other tiles, use the set of grout
brushes with gray bristles included
with your FloorMate TM
SpinScrub v< 800 Cleaner. Use these for tile floors where extra
attention
is needed for cleaning grout. (See "Cleaning
the brushes" section for how to _>move and _>place the brush assemblies.)

Using cap (A), measure
Cleaner.

DO NOT

use cleaning

concentrates

that

contain

solvent

1-1/2 capflfls (3 oz.) of HOOVER(_)Grout

based

ingredients.

Pour cleaning concentrate into tank (B). Fill tank to
line (C) (1 quart) with warm water.

Cont_nu_,d

If rubber ring (D) on cap has become dislodged,
reposiit with uneven side against ledge (E) as shown.

Replace
cap. Rotate
must be locked
and to prevent
leaking.

Slide tank
place.

straight

Recovery

(lower)

Automatic

shut-off

cap clockwise
until
in place for proper

into

position

until

it locks in place.
performance

latch

snaps

the

recovery

tank

An automatic
suction
shut-off
tank to prevent
the tank from

is built into
overflowing.

When
the shut-off
activates,
the cleaner
will not pick up
debris
and the sound
of the motor
will change.
The recovery tank is full and must be emptied.

How to empty
"x

Turn

cleaner

off and

disconnect

from

electrical

outlet.

Although
not necessary
for satisfacto_\y
performance,
it
is recommended
that the recovery
tank be emptied
after
dry vacuuming
and before wet operation.
Check the solution
tank also. It may need to be refilled
at this time.

To remove
tank, press
pull tank straight

Remove

down
out.

on release

tank lid (C). Empty

button

(B)

tank.

To clean filters
The
this

tank lid contains
a washable,
pleated
filter" when
suction

Turn cleaner

reusable
filter.
is low or reduced.

OFF and disconnect

from electrical

Clean

outlet.

Remove recovery tank and lid (Figs. 27 & 28).
filter" lid (A), then remove filter" (B).
Remove loose debris from filter by tapping the filter or
gently brushing using your hand. The filter" may also be
rinsed for additional cleaning. Allow filter to air" dry
between uses.

Reposition

filter.

Replace filter" lid. Press down firmly until snapped
place.

Continued

Dry or loose debris
in the tank lid.

will

also collect

on the filter

screen

To remove debris from screen, remove the pleated
the lid. Remove debris from screen (D).
The filter screen
running
water.

may

also

be cleaned

by rinsing

filter

it under

Reposition
pleated
filter in lid. Replace
lid onto
pressing
down
firmly until snapped
in place.

To replace
recovery
ledge
(E) and push
locked
in place.

located

recovery

tank,

tank, place bottom
of tank behind
tank straight
into cleaner
body until

it is

Recommended
Use your

HOOVER')

cleaning
FloorMate

sequence
SpinScrub

800 Cleaner

to:

o Dry Vacuum
to remove
loose dirt, hair and debris.
• Wet Clean
the floor surface.
The brushes
will provide
, W'et Pickup
reduces
drying
time of the floor surface.
The

Mode

raised
To wet
position

selector

dial

turns

, debris
pickup,
In this position,
off the floor surface.
clean
(B).

with

For wet pickup,

brushes

light

the

agitation

brushes

on and

turn the dial
the brushes
turned

ON,

to help

loosen

dirt.

off.

to the DRY VAC
posiwill not rotate and are

turn

the

turn the dial to the WET PICKUP

dial

to the

position

WASH

(C).

NOTE:
Your HOOVER€)
FloorMate
TM
SpinScrub
T< 800 cleaner
may be used to clean
that have been sealed
with a polyurethane
coating
and can be cleaned
with water.

wood

CAUTION:

cleaning

To prevent

damage to wood floors, follow the flooring

manufacturer's

floors

rec-

If using cleaner on sealed wood floors, inspect floor surface for worn finish, bare wood or separated joints. Do not use FloorMate TM SpinScrub TM cleaner to wet clean sealed wood floors if any
of these conditions exist.

Set Mode selector dial to DRY VAC position and vacuum

floor.

Turn cleaner off" and disconnect from electrical outlet. Empty recovery tank (see Figs. 27
and 28). Determine the type of brushes to be used (either gray for ceramic and other tiles or
white for vinyl and sealed wood floors). See "Cleaning the brushes" for removing and
replacing brushes.
Fill solution tank
¸¸¸3¸¸¸¸¸
depending upon

with either Floor to Floor TM Cleaning Concentrate or Grout Cleaner,
the type of floor being cleaned, and water (see Figs. 20 through 26).

Do not use solvent based cleaning
wax in your cleaner.

concentrates

in your cleaner. Do not use any type of

'IkJrn Mode selector dial to WASH position.

Dry hands and plug cleaner into a properly

grounded

outlet.

Step on handle release pedal and lower handle to operating

To release solution, squeeze trigger (A) (Fig. 34). Slowly
move cleaner forward and backward over area to be cleaned.
Squeeze trigger to release solution as needed.
Overlap , strokes by one inch to help prevent streaking. The
cleaner s suction will pick up the dirty solution throughout

position.

Turn cleaner ON.
__
,///Y_-)/
/_/_
//
.f
// /
/ /

\ A
"A

cleaning.
_
J
To greatly enhance drying of the floor surface, release trigger k_
jd
and turn Mode selector dial to the WET PICKUP position. Continue to move cleaner over the
area to pick up the dirty solution.

continue
¸9¸¸¸¸To
through 9.

cleaning another

area, turn Mode selector dial to WASH position. Repeat steps 7

Note: When cleaning sealed wood floors, make sure all areas are completely" dr> Ensure
that no water remains on the floor.
Note: When switching between wet cleaning and wet pickup, it is not necessary
cleaner ofT. Simply move the Mode selector dial between the two settings.

to turn the

Empty recovery tank or clean the filter when the motor sotmd becomes higher in pitch and
there is a loss of suction (see "Automatic shut-off" section).

Picking

up spills

Your cleaner may also be used to pick up small liquid spills (1 quart or less, never to
exceed 114 inch in depth) on non-carpeted
floors. Turn Mode selector dial to the WET PICKUP position and release the trigger. Continue to move cleaner over the a_>a to pick up the
spill.
Do not use the cleaner to pick up flammable
or combustible
liquids
or chemicals,
use the cleaner to pick up detergents
that contain solvent based ingredients.
ContJnuect

do not
_

Select tool
A. Floor swivel
tool
* Swivel
head
* 2 rows

of brushes

o Use

to clean

Grout

tool

small,

* Stiff brushes
on stubborn

tight

areas

to use for more,
grout stains

concentrated

cleaning

k,.

Attach
Unplug

hose

cleaner

and tool
from

How to connect
/Open
/
/

hose

Align

Insert

hose

How

hose

outlet.

hose
door

(A) on side

connector

/
To disconnect
connector.
Remove
/

electrical

of cleaner.

(B) with
(B) until

hose

it snaps

hose: Squeeze
the
hose from port.

door

and

solution

ports

(C).

in place.

hook

(D) on bottom

of hose

tightly.

to connect

telescoping

/ Slide wand
(C) on hose.

wand

(A) onto hose end (B). Snap wand

over tab

/
To extend
telescoping
wand,
pull button
(D) toward
you and pull wand
away from you to the desired
length.
The full
extension
of the wand
is indicated
by a 'MAX'
line. It is recommended
you do not extend
the wand
past this line.

/ To remove wand:
Slide wand off hose.

How

to connect

Tools may
telescoping

All tools

Push

forward

directly

in the

/ Slide tool onto
on hose or wand.

same

hose

to the

hose

or onto

the

manner.

or wand.

/
To remove
tool: Push fo_aNard
Slide tool off hose or wand.

(E).

tools

be attached
wand.
attach

and up on latch

and

Snap

tool

over

on latch

tab

(B).

(A)

oThe
get

handle
cleaning

Using
/

the

Squeeze
cleaning

Turn

storing
cleaner

and hold
solution.

in order

)

trigger

and pull
without

(A) in hose

grip

tool over same area
putting
down
more

to release

to pick
solution.

cleaner:
OFF

and

disconnect

Empty
dry.

•

Press on upper
storage.

handle

•

Make

nothing

•

Do not store

sure

rinse

and

•

completely-

position
hose.

tool

Let go of trigger
up dirty solution

Before

that

solution

cleaner

and

release

from
recovery

button

is pressing
on a wood

electrical
tanks.

outlet,
Allow

to lower

on the
surface

handle

for

squeegee.

nozzle

unless

to air

cleaner

dry.

must be in the upright
solution
through
the

For your convenience,
the HOOVER@
FloorMate
TM
SpinScrub
TM
800 tool caddy
(A) is provided
for storing
the hose, tools, telescoping
wand,
set of brushes
and
detergent.
The two sections
of the tool caddy
snap together
%r assembly.
Press where
indicated
by arrows
to snap securely
in place. The
caddy
conveniently
fits over" the top of the cleaner
nozzle
(B)
for storage.

F
J

To store hose:
Place the hose grip (C) into slot (D) on
of caddy.
Pull hose up and press into cut-out
area
rE). Continue
wrapping
hose down,
underneath
tongue
(F),
and back tap, pressing
into second
cut-out
area (C). Place hose
end (H) into slot (I) on back of caddy.
Place floor swivel
tool (J), grout tool (K), brush assembly
(L), telescoping
wand (M) and detergent
(N) into caddy

JN
as

sho_wn.

Continued

Cleaning

the nozzle

Turn cleaner

OFF and disconnec{

The cleaner's

nozzle can be removed

Slide the two

nozzle

release

from electrical

for easy cleaning.

latches

(A) outward.

Remove nozzle (B) by pulling straight

out.

Rinse nozzle under running water. Remove
tueegee (C) and wipe with a damp cloth.

outlet.

debris

from

nozzle, make sure latches (D) are out.

should be in the upright
bly of the nozzle.

position

Align middle section (E) of nozzle with opening

for easier" assem-

i
\

(F) on cleaner:

While holding nozzle in place, slide latches inward to lock
in place.

Cleaning

the brushes

The brush assembly
Turn cleaner

can be removed

OFF and disconnect

Place handle in the upright

for easy cleaning.

from electrical

outlet.

position.

Remove tanks to pr>vent leaking. Set aside.
Pull the two nozzle release buttons

(A) out. Remove nozzle.

B
Tilt cleaner" back so handle
Push two brush
r assembly.

rests on floor.

release

buttons

(B) and remove

The brushes can be washed with a mild
not use a solvent based detergent.

detergent

the brush

and rinsed. Do

replace brushes, align post (C) on brush block with hole
on bottom of cleaner'. Turn brushes slightly until post
fits easily into hole. P_>ss brush assembly firmly to snap into
place.

Return cleaner to upright
latches (E) are out.

position.

Replace nozzle, making

Align middle section (F) of nozzle with opening

While holding
place.

(G) on cleaner.

nozzle in place, slide latches inward to lock

Replace tanks.

,._

Continued

,,_

Use

the

list below

to help

solve

minor

problems.

,/Make
sure the cleaner
plugged in firmly.

C]eaner won't run

Low suction

/ Check

the fuse or breaker.

V"Empty
andthe

the recovery tank; it may be full
automatic
shut-off engaged.

¢" Make sure filter and filter" lid are properly
positioned.
,/Make

sure tanks

¢" Check

are locked

the filter" and clean if dirty.

,/Make
sure nozzle
and locked.
,/Make
when
Water

puddling

behind

cleaner

pick

tap dirty

solution

is replaced

properly

stare the hose door is closed
not using the hose.

¢" Use recommended
excess foaming.
,/Make
sure solution
properly.
,/Empty

Won't

in place.

detergents

tightly

to reduce

tank is installed

recove W tank.

,/Check
Mode selector
set for WET PICKUR

dial to ensure

,/Make
sure recovery
properly.
,/Empty

recovery

it is

tank is installed

tank.

,/Make
sin> filter and filter lid are properly
positioned.

Cleaner pushes a line of dry debris
in front of it

,/Check
Model selector
set forDRY VAC.

dial to ensure

it is

V" Tip nozzle off floor by pushin_
down on
handle to pick up debris that i_ too large
to clear

Cleaning solution

won't

dispense

the

squeegee.

¢" Make sure solution
position.
¢" Refill the solution
¢" Puu)pneeds
tool).

Brushes

won't

rotate

See

page

tank

circuit

(1) Push
OFE

tank if it is empty.

to be, primed
lb.

_" Check Mode selector
set for WASH.
¢' Reset

is locked

(when

dial to ensure

using
it is

breaker'.

ON/OFF

switch

to turn cleaner

Walt one cleaner
minute. into electrical outlet.
21 Plugthe
nplug
the <:leaner'.
,5 Pus];r the ON/OFF
switch again to
turn

cleaner

ON.

If the brushes continue
to stall and the
breaker trips again, clean the brushes to
remove debris.
18

Lubrication
The motor is equipped with bearings which contain sufficient lubrication for the life of the motor.
The addition of lubricant could cause damage. Do not add lubricant to motor bearings.

1"oobtain approved HOOVER service and genuine HOOVER parts, locate the nearest Hoover
Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot) by:
/ Checking

the Service Section oi The Hoover

Company

,/Checking

the

provided

,/Checking

the Yellow Pages under

list of Fac[ory

_/Calling
1-800-944-9200
{U.S. onlvt
Do not send your
in delay.

cleaner

If fl_rther assistance
Phone:
330-499-9499.

In Canada

contact

Always identify your
ing parts. /The model

Centers

"Vacuum Cleaners

for an automated

to The Hoover

is needed

Hoover

Service

contact

Canada.

referral

Company

The

Hoover

Burlington

with

this

Company

cleaner

- Household"

of at_thorized

in North

Ontario

on-line at wxvw.hoover.com

Can_on

L7R 4A8 Phone:

cleaner by the complete
model number
when
number
appears on the back of the cleaner./

service

outlet

for serwce:

Consumer

locations

this will only result

Response

Center.

1-800-263-6376.

requesting

information

or order-

Full One Year
Warranty
(Domestic

Use)

Your HOOVER(,'_ appliance is warranted in normal household use, in
accordance with the Owner's
Manual against original defects in
material and workmanship
fbr a
period of one fidl year fl'om date of
purchase. This warranty provides, at
no cost to you, all labor and parts to
place this appliance in correct operating condition during the warranted
period. This vvarranty applies when
the appliance is purchased in the
United States including its territories
and possessions, or in Canada or
fl'om a U S. Military Exchange.
Appliances purchased elsewhere are
covered by a limited one year warranty which covers the cost of parts
only. This warran V does not apply if
the appliance is used in a commetr:ial
or rental application.
This warranty only applies when the
product is in use in the country or
territory in which it is purchased.
Warranty
service can only be
obtained
by presenting
the appliance
to one of the fbllovving
authorized
warranty
service outlets. Proof of
purchase
will be requh'ed
befbre set'vice is rendered.

1. Hoover Factory Service
Centers.
2. Hoover Authorized
Warranty
Service Dealers (Depots).
For an automated referral of authorized selwice outlets in the U.S.A.,
phone 1-800-944-9200 OR
visit The Hoover Company on-line
at

WWv_.hoogeg

con]

This warranty does not cover pick
up deliver_ or house calls; however,
if you mail your appliance to a
Hoover Factory Service Center fin"
warranty service, transportation
will
be paid one way.
While this warranty gives you specific legal rights, you may also have
other rights which vary fl'om state to
state.
If fiJrther assistance
is needed,
or if
there are questions
concerning
this
warranty
or the availability
of warranty service outlets, write or phone
the Consumer Response Center,
Phone 1-330-499-9499.
In Canada, contact Hoover Canada,
Burlington,
Ontario
L7R 4A8,
1-800-2(13-6376.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 20
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Thu Apr 05 11:53:55 2007
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

Hoover H3060 User Manual Manuals And Guides L0502276

HOOVER Power Steamer Manual L0502276 HOOVER Power Steamer Owner's Manual, HOOVER Power Steamer installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation