Hoover Concept One Manual 820242 ManualsLib Makes It Easy To Find Manuals Online! User

2016-05-04

User Manual: Hoover Hoover-Concept-One-Manual-820242

Open the PDF directly: View PDF .
Page Count: 24

Download
Open PDF In Browser	View PDF

Fill in and retain!
IIIt'llll'll

II II

II1'11111
IIIIIl'lll
IIIIIIll

I II II

I'LI'H

The HOOVER vacuum cleaner you have just purchased is a combination cleaner. It is used for carpet and rug cleaning and may be used
with attachments for above the floor cleaning.
The model and serial number appear toward the rear of the bottom of
the cleaner.
For your personal records, please enter these numbers in the spaces
provided below and retain in a safe place.
Your cleaner is model
and has serial number

Save!
Index
Assembling Cleaner .............................
Cleaner Description ...........................
How to Use

5
3,4

Cleaning Tools .............................
Special Features ..............................
Upright Cleaner .............................
If You Have a Problem ..........................

9-12
7
6-8
21

Important Safeguards ...........................
Lubrication ...................................
Maintenance
Authorized Hoover Service ....................
Dirt Duct and Dirt Tube
Replacing
Replacing
Replacing
Replacing

....................

Belts ...........................
Brushes ........................
Headlight .......................
Throw Away Bag ................

2
22
21
18,19
15-18
20,21
14,15
12-14

Company

B i

Important

Safeguards!

• Read all instructions.
• Warning: Electric shock could occur if used outdoors or on wet
surfaces.
Close supervision
is necessary when any appliance is used by or
near children. Do not allow vacuum cleaner to be used as a toy or to
run unattended
at any time.

Keep hands, feet, loose clothing, and hair away from rotating agitator. Do not operate cleaner in bare feet or when wearing open toe
shoes or sandals.
• Don't run cleaner over cord. It may damage insulation.
• Do not use cleaner to pick up matches,
butts.

or live ashes and cigarette

Never vacuum in the presence of flammable
or fumes.

or combustible

liquids

• Avoid picking up hard, sharp objects with the cleaner. They may
damage the cleaner and the bag.
• Do not allow cleaner to run in a stationary position on non-carpeted
floors; damage could occur to these surfaces.
• Unplug cleaner when not in use. Turn machine off at switch before
unplugging.
• Always disconnect cord from electrical outlet before servicing the
cleaner.
Change bag frequently
powder.

when picking up very fine materials such as

Grasp the plug to disconnect from wall outlet to avoid damage to
cord, plug, prongs, or receptacle.
If cleaner has a cord reel, hold on to the plug while cord is being rewound to prevent cord from whipping.
o

The use of an extension cord is not recommended,

If cleaner

is in disrepair,

do not attempt

to operate,

Have repairs made by the qualified personnel at Hoover Factory
Service Centers or Authorized Hoover Warranty Service Dealers.
•

Use vacuum cleaner only for its intended use as described in the
instructions.
Use only attachments
recommended
by the appliance
manufacturer;
others may cause hazards.

Save these instructions!
2

Unpacking
7

Handle
section

Unpack the cleaner from the carton and remove and dispose of
cardboard
packing.

12
Make a small loop with cord and
place it over the hook at the back
of the handle. When operating,
cord should be positioned
as
shown.

Before operating
your cleaner,
identify features and controls
shown in the diagram, then,
read the section on "How
to usq

1. Edge Cleaning:
Brushed edge cleaning
of the cleaner. Standard
edge cleaning

is provided
is provided

2. Handle Release Pedal: step on pedal to lower
operating
or low position.
3. Cord

Reel: to unwind

cord,

pull from

4. Cord Return Button:
depress
storage. Hold plug until cord
5. Vinyl

Bag Jacket:

6. Bag Spring:
7. ON-OFF
8. Handle

place

'Power

covering
spring
Surge'

cord

handle

rewind

cord for

ring over hook

to support

the bag.

Switch

Grip.
tablet

and

Headlight

I1. Carpet Height
or "SHAG".
12. Molded

Adjustment

Furniture

Lever:

choose"

LOW/M

cleaner

ED",

"P LU S H",

Guard

_lote: If using cleaner on new carpet, be sure to change
_ee "Maintenance"
section for bag replacement.
)perate
_leaner.

length.

away bag.

9. Air Freshener
Dispenser:
designed to hold a fragrance
release a pleasant scent during cleaning.
10. Twin

to either

reel to desired

to automatically
is rewound.

for throw

on the right side
on the left side.

only at voltage

specified

on data

bag frequently.

plate on bottom

How to assemble
Remove the tape holding the two
handle attachment
screws from
the lower end of the handle. Set
screws aside.

CORD

Align handle with ON-OFF switch
to the rear of the cleaner and label
to the front. Fold cord beside cord
tube as shown. Push cord and
tube completely up into handle.

Insert handle into the cleaner to
the line indicated on label. Insertion to the line is necessary for
proper screw alignment.

Lower handle to operating
position and place spring bag ring over
hook located on handle.

Insert the two screws
Remove paper bag from inside the
vinyl jacket. Then remove dirt tube
by pushing to either side to release
retention
clips. Lift tube up and
out,

holes provided
housing.

Tighten with screwdriver.
Snap
dirt duct back into place. Replac_
paper bag. (Follow instructions
on bag. )
Zip vinyl jacket.

into the

inside the front

Check air freshener
dispenser
The small drawer in the top of the
bag cap should not be removed.
If it should become detached,
replace by unhooking
the bag
spring and tipping the bottom of
the drawer to insert projections
into back of cap opening.
Push
drawer down into position and
hook bag spring.

How to use
To transport
To move your cleaner from room
to room, put the handle in the upright position,
tilt the cleaner back
on the large rear wheels and push
forward.

Handle adjustment
The handle of your cleaner has
three positions:
Upright for storage and when using attachments.
Operating
for general operation
on
carpet and foors. Low for reaching
under low furniture.
The handle
can be lowered by stepping
on the
pedal at the rear of the cleaner.

ON-OFF
switch

"Power Surge"

Operate your cleaner at normal
speed by pushing the switch down
one position. To turn cleaner off,
push switch up.
Normal Speed is to be used for
regular cleaning of carpet and rugs
and when using cleaning tools.
Your cleaner is also equipped with
a Power Surge switch. When the
switch is pushed down as far as
possible it is in the Power Surge
speed.
"Power Surge" Speed is to be
used for extra cleaning power on a
heavily soiled area of carpet. Slide
the switch down as far as possible
and hold it in that position to engage the "POWER
SURGE"
speed. When the switch is released, it will return to the NORMAL speed position.
Note: When cleaning any floor
covering,
turn cleaner "OFF"
when unattended,
particularly
on
non-carpeted
floors. The agitator
cleans so thoroughly
that operation while the cleaner is stationary
may mar the floor covering.

Special features
Edge cleaning
Brushed edge cleaning is provided
on the right side of the cleaner to
remove imbedded
dirt in carpet
near baseboards
and furniture.
Guide the right side of the cleaner
parallel to the edge of carpet or
furniture
for brushed edge cleaning.
Standard edge cleaning is provided on the left side of the cleaner.
Standard edge cleaning removes
surface dust and litter.

OFF
NORMAL-a
'POWER
SURGE"
i

Adjustment

for carpet

pile height
The cleaning of carpet and rugs
takes place at the nozzle. This is
the opening at the bottom of the
cleaner where the agitator is located.
NOZZLE
,.u

It is necessary for the nozzle to be
adjusted
properly to the various
carpet pile heights. The adjustment lever on the front of the
cleaner may be set on three different self-adjusting
ranges.
On very dense pile plush or shag
carpet, some difficulty
in pushing
the cleaner may occur. In this
case, position the adjustment
lever on PLUSH or SHAG. When
cleaning non-carpeted
floors, set
adjustment
lever to LOW/MEDIUM and use Normal Speed. Because of the vigorous action of
the agitator,
do not allow
cleaner to run in a stationary
position on any floor covering, as
marring may occur.
Disconnect
cleaner from electrical outlet before making nozzle
adjustment.
To change the nozzle adjustment
grasp the handle and tilt the
cleaner forward.
Move the lever
with your hand until it "clicks"
into the desired position.

Air freshener dispenser
Lift drawer in the bag cap of your
cleaner and insert the air freshener
tablet that has been packed with
your cleaner. Push drawer down
into position.

The amount of fragrance released
is regulated by sliding the control
to one of three settings shown on
top of the bag cap.
Air freshener tablets may be obtained from your local authorized
Hoover dealer, a Hoover Factory
Service Center, or by using the
mail order form packed with your
cleaner.

Cleaning

Min Max

Tools

This cleaner may be used with cleaning tool attachments.
The Deluxe or
Standard
cleaning tool set may be purchased
at additional
cost from
Hoover Dealers. The cleaning tools allow you to do above the floor clean.
ing and to clean hard to reach areas.

Deluxe cleaning
tool set
U3901 includes vinyl hose, converter, wands, dusting brush, furniture nozzle, wall/floor
brush
and crevice tool.

Standard
cleaning tool set
U3903 includes lightweight
hose,
converter,
wand, multi-purpose
brush and crevice tool.

How to assemble hose
and converter
By using this converter
attachment, suction is channeled from
the cleaner to the hose and cleaning tools.

,,, ul

i in,ii i, i,,

HOLES
The converter
must first be assembled to the hose by inserting
the converter
into the hose connector.
CONNECTOR

CONVERTER

Push connector

and converter

to-

gether and twist until the projections on the converter
fit into the
holes on the hose connector.
This
unit should remain assembled for
all future tool use.

Using cleaning tools
A. Attach

converter

Disconnect
cleaner from electrical outlet. Cleaner must not be
plugged in when positioning
removing converter.

With cleaner in upright position,
grasp handle and lean cleaner
backwards until bag is flat on the
floor and underside is accessible.

Turn lock on converter
serrated
hose.

portion

Pivot converter
opening.

so that the

is in line with

the

until

the

it covers

Place projections
on converter
onto rim on bottom plate of
cleaner.

Place edge of lock in slot on
cleaner and turn lock to secure
converter.
Raise cleaner

to upright

position.

B. Select proper cleaning
tool

The cleaning tools have many
uses. Select the tool best suited
for the cleaning task from the descriptions
below.
1. Wail/floor
brush* for walls and
very irregular hard surface floors
such as brick and slate.

4
3

2. Furniture
nozzle* for upholstered furniture,
draperies,
tapestries, mattresses,
clothing,
automobile interiors and carpeted
stairs.
3. Multi-purpose
brush (standard
set only) for dusting surfaces such
as table tops, lamp shades, draperies as well as for cleaning upholstered furniture,
stairs and automobile
interiors.
4. Dusting brush* for carved furniture, table tops, books, lamps,
lighting fixtures, venetian blinds,
baseboards,
shutters and registers,
5. Crevice tool for radiators,
dresser drawers, spaces between
kitchen appliances.
6. Wand(s*)
used to give extra
length to your hose. They are ideal
to reach ceilings, the top of draperies, high shelves and cupboards. Use them with any of the
above tools.
*Included

in deluxe

set only.

C. Attach tool
The outer plastic ring on the end
of the hose grip has a slot.
Turn the ring until that slot aligns
with the slot in the hose connector.
Insert the tool so that the button
on the tool fits into the aligned
slots.

Turn the plastic ring as shown to
lock the too! in place. To remove
tools, reverse the procedure.
LOCK

For additional
length, attach wand
to the hose using the same procedure as for attaching
tools
Tools attach to the wand
same manner.

in the

D. Adjust switch and
handle position
Place handle in the upright
position, and slide ON-OFF switch to
Normal Speed.
_[V

Plug clean
cleaner attachments
into electrical
To

outlet.

To clean the hose wipe off dirt
with a cloth dampened
with a liquid detergent.
Rinse with a damp
cloth. Cleaning tools may be
washed in warm water with a detergent.
using.

Rinse and let dry before

Maintenance
The following
sections are concerned
with proper maintenance
of the
cleaner. Familiarize yourself with these home maintenance
tasks and
keep this owner's manual in a convenient
place where you can refer to it
when needed. Proper use and care of your cleaner will assure continued
cleaning effectiveness.

The bag
Your cleaner has a durable outer
A light wiping with a damp cloth

bag which covers the throw away
will keep this outer bag clean.

bag.

When
to replace
the throw
away
bag
Check the bag from time to time. It is recommended that you change the
bag when the dirt reaches the dotted line on the throw away bag. If you
let more dirt than this accumulate, your cleaner may not operate effectively. Change bag frequently when using cleaner on new carpet, due to
rapid accumulation of carpet fluff. Also check dirt duct (see section following belt replacement) for fluff accumulation.

Where

to buy bags

Bags may be purchased
from your local Authorized
Hoover Dealer or
from a Hoover Factory Service Center. When ordering
bags, be sure to
give the model number
of your cleaner.

What

bags to buy

Use HOOVER

bag type

A with

this cleaner.

_®

To assure that your HOOVER cleaner operates at peak performance,
it is imperative
that you use only genuine
HOOVER throw away bags made by The Hoover Company.
HOOVER bags can be identified
by the trademarks
-- --

How to change

bag

Disconnect cleaner from electrical outlet.

1. To remove old bag, put fingers
behind bag collar, pull off and remove.
Dispose

of old bag.

Do not try to clean out used bag.
Cleaner will not operate effectively.

2. Tuck bottom
in first.

of new paper bag

3. Push cardboard
bag collar firmly
onto fill tube by first, positioning
bottom of collar, and then top,
onto tube. Make sure the collar is
pushed past the raised portion at
the top and bottom and tightly in
place on the tapered portion of the
tube. This will insure a firmly sealed position.

4. Tuck remainder of bag into
outer jacket. Zip shut.

The headlight
Disconnect cleaner from electrical outlet.
This cleaner uses two 12 volt,
wedge base type 912 bulbs.
1. Lower

the handle

cleaner is positioned
flat on the floor.

until the
with the bag

2. Use screwdriver
to lift lens.
Place screwdriver
in the two slots
provided at the top edge under
ridge of lens as shown. Turn
screwdriver
to loosen lens.

3. Lift out lens.

4. Remove bulbs by pulling
straight out of sockets. Replace
by pushing each bulb straight into
the socket until it locks in place.
(Excessive force is not required).

5. Replace
projections
cleaner.

6. Press firmly at center and sides
of lens to snap into place.

lens by inserting plastic
into openings
in

The belt
-/he belt drives the agitator and is
important
for the efficient
operation of your cleaner. Because of
this, when buying a new belt, you
should always insist on a genuine
HOOVER belt. Some other belts
on the market, not manufactured
under the Hoover design and
quality controls,
may not operate
the agitator correctly
and may
damage your cleaner.

When to replace belt
Check from time to time to be sure
the belt is in good condition.
If it
is stretched,
cut, or broken, it
should be replaced.

AGITATOR

BELT

How

to replace

agitator

belt
Disconnect
cleaner from electrical outlet before replacing belt.
Place the cleaner

on the floor.

For ease in installation,
follow the
directions
given below and position yourself to the left, rear of the
cleaner.

1. Turn cleaner over. Release
handle to lowest position. Remove
plate on bottom of cleaner by releasing clips. (See illustration)

2. Remove
shown.

bottom

plate

3. To remove the agitator, use a
screwdriver placed as shown.

PLATES

4. Use one hand to remove the
agitator as you use leverage to lift
the agitator with the end of the
screwdriver.
Remove old belt.

5. If the end plates have loosened,
tighten them by turning in opposite directions.

MOTOR
PULLEY

6. Place one end of the new belt over the metal motor pulley. Lettering
on belt should be visible and not against pulleys. Slip the other end
around the plastic pulley end of the agitator. (See illustration)

AGITATOR

END PLATE

7, Grasp the agitator frimly with
one hand. (Be sure you can see
the agitator end plate,) Engage
screwdriver
as shown for lever-

8. Lift and pull using screwdriver
as a lever. Guide the end opposite
the belt into position first,

age,

9. Quickly roll the other
agitator into place.

side of

10, Press firmly to be sure agitator
is securely in place.

/
J
• _--

11. Bottom plate attaches in a
hinge-like
motion.
Place the
groove on the front of the bottom
plate over the notched edge on the
front of the cleaner.

13. Lift and snap retaining
into place.

, _y-_--m

12. Maintaining
front connection,
rotate bottom plate to cover bottom of cleaner, Make sure dirt
duct is in position under
plate. Press firmly.

bottom

clips

Dirt duct and dirt tube
To maintain the strong suction and cleaning effectiveness
of your cleaner, remove any large items from the carpet surface before vacuuming.
However,
if your cleaner picks up a larger object than can be exhausted
in the bag, it can be caught in the dirt duct or dirt tube. These are easily
cleaned out by the following
methods.

Disconnect
cal outlet.

cleaner from

electri-

For access to the dirt duct, turn
cleaner over to expose underside.
Remove bottom plate. Lift dirt
duct as shown and pull out any
obstructions
with your fingers.
Reposition
dirt duct by lowering to
operating
position and then replace bottom plate.

For access to the dirt tube, first
remove disposable
bag. Then remove dirt tube by pushing to
either side to release clips. Lift
dirt tube up and out.

To replace dirt tube, position over
lower seal and push down. Insert
one side against retention
clips.
Push to snap other side into position.

Clean out dirt tube.

Agitator brushes
Disconnect
cleaner from electrical outlet before checking
brushes.
When

brushes

are worn

and

bristles do not touch the edge of a
card held across the nozzle, they
should be replaced. Always replace both brushes at the same
time to maintain cleaning effectiveness.

To replace
Disconnect
cal outlet,

brushes
cleaner

Remove bottom
agitator following
viously given.

from electri-

plate, belt and
directions
pre-

1. Hold agitator as shown. Turn
end plates in opposite directions
until one end plate comes off.

END
SECTION

2. Pull or pry out end sections
shown in illustration.

Note: Pulley end should be removed by pulling straight out.
3. Note position of bar/brush
assemblies to insure correct replacement.
BAR/BRUSH
ASSEMBLY

Remove bar/brush
assemblies
by
pulling them from agitator slots.
Use pliers if necessary.
The word "BAR"
is stamped
near the slots on the agitator.
Match the bar side of the bar/
brush assembly with the label on
the agitator shell. Slide the new
assemblies into the slots, while
twisting
the assemblies
in a
counterclockwise
motion.
Push
in as far as possible, tapping the
outer end lightly if necessary.
Be
sure brushes and bars are aligned
for full length of agitator.

END
WASH

SECTION
ER

BEARING

LOCATOR

4. Reassemble
agitator parts.
Line up Iocator on end sections
with slot on agitator.
Note: Large
Iocator on pulley end must align
with large notch on agitator.
Screw

on end plates

5. Should you accidentally
displace the bearing during disassembly, reassemble as shown.
Replace belt, agitator and bottom
plate.

and tighten.

If you have a problem
This appliance
was inspected
thoroughly
and was in good operating
condition when it was shipped from the factory.
If a minor problem develops,
it usually can be remedied quite easily when the cause is identified.
Accordingly,
this check list is provided for your convenience.

Problem

Possible cause

Possible solution

Cleaner
won't
run

1. Not firmly plugged in,
2. No voltage in wall plug.
3. Blown fuse/tripped
breaker.

1. Plug unit in firmly,
2. Check fuse or breaker.
3. Replace fuse/reset breakeu

won't
pick up

belt.
2. Agitator brushes worn.
3, Bag full.
4. Obstruction
in cleaner.
5. Bag not opening.

2. Replace brushes.
3. Change throw away bag.
4. Clear pivoting
dirt duct
and/or dirt tube.
5. Check for firm bag connection.

If the problem
persists, check the Yellow Pages of your telephone
book
under "Vacuum
Cleaners - Household"
for your nearest Hoover Factory
Service Center or Authorized
Warranty
Service Dealer where approve(
HOOVER service and genuine HOOVER replacement
parts may be obtained. The warranty
provided with this product has a listing of the
Hoover Factory Service Centers. If you are unable to obtain the information you need from the Yellow Pages, contact a Hoover Factory Service
Center to find your nearest Authorized
Warranty
Service Dealer. For
service under warranty,
follow the instructions
in the Warranty
provided
with this product.
Do not send your cleaner to The Hoover
service as this will only result in delay.

Company

in North

Canton

for

Always identify your cleaner by model number when requesting information or ordering replacement parts. (The model number appears on the
bottom of the cleaner.)
If further assistance is needed, contact The Hoover Company Consumer Affairs Department,

North Canton,

Ohio 44720, 216-499-9200.

Lubrication
The motor is equipped with one ball bearing and one needle roller bearing. These bearings contain sufficient lubrication for the life of the motor.
The addition of lubricant could cause damage. Therefore, do not add
lubricant to either motor bearing.
The agitator is equipped with two ball bearings that should be lubricated
periodically. This should be done by a Hoover Factory Branch Service
Center or an Authorized Hoover Warranty Service Dealer.

Energy saving tips
1. Replace throw away cleaner bag promptly, before overfilled,
genuine HOOVER bag made for your cleaner model.
2. To maintain effective
necessary,
when

cleaning,

with a

replace agitator brushes and belt when

Turn off cleaner

not in use, such as when

moving

furniture.

Keep your cleaner operating
at peak performance
level - have inspection and service performed
by a Hoover Factory Service Center or
Authorized
Hoover Service Dealer.

VCMA

VACU UM - CLEANER
MANUFACTURERS
(HOOVER
AN ASSOCIATION
MEMBER)

ASSOCIATION

Service To The Consumer Since 19t3

This reformation
has been compiled by the Vacuum Cleaner Manufacturers
Assoc_
ation from Government
and Private Sources concerned
with product
safety. These
basic guidehnes
are for your protechon
and convenience,
TO AVOID

ELECTRIC

Never vacuum
Do not store
Replace

damp

or liquids.

outdoors.

or frayed

power

cord

immediately.

ACCIDENTS

Never vacuum

live ashes or cigarette

Never

run machine

Never

let children

Use extra caution
Except

or wet surfaces

machine

worn

TO AVOID

SHOCK

for hand

butts.

over or place sharp objects
use machine
when

or) stairs.
keep machine

on floor

When machine is turned on, never allow fingers,
near intake suction ports or revolving brushes.
Never

leave machine

Turn machine

running

off at switch

When unplugging
wrapping
or cord

or cord
before

in the presence

Always unplug
accessories

power

and accessories
PERFORMANCE

Keep

machine

Have machine

cleaning

checked

Use only manufacturer's
Store machine

carefully

cord and plug during

of flammable

or combustible
before

only _n manner

machine

accidents

from

or attachir)g

tripping

brushes

periodically

when

worn,

and in good

operating

authorized

service

center

condition.
to maintain

hair or other foreign
cord.

after unplugging

by manufacturer's

over power

by manufacturers.

filters as recommended
by manufacturer
after unplugging
the power cord.

authorized

the power
service

material
cord.
center,

for parts or service.

in a dry area,

THE HOOVER COMPANY,
U4219

or fumes,

servicing

intended

clean

liquids

For optimum
cleanin 9 performance
and safety, study and follow
Manual -keep
it in a handy and safe place for future reference.

5-.86

etc. to come

unattended.

guide

check revolving brush for build,up of lint,
as necessary,
after unpluggirrg
the power

or replace

etc

wall outlet.

not cord;

and all accessories

Change or clean bags and/or
optimum
cleaning
efficiency,

Adjust

from

after each use to prevent

FOR BEST

Periodically
and remove

tables,

eyes, hair, garments,

in when

unplugging

cord from wall outlet

Store machine promptly
cord or machine.

your

not on chairs,

cord is not recommended.

Never vacuum

Use machine

plugged

machine, grasp plug
reel rewinding.

The use of an extension

cord.

as a toy.

cleaning

held cleaners,

on the power

NORTH CANTON,
LithoUSA

your

Owner's

OHIO 44720
56511-262

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Author                          : Provided By MANUALSLIB.COM - http://www.manualslib.com/
Create Date                     : 2013:06:08 10:03:48Z
Keywords                        : manuals, instruction manuals, user manuals, service manuals, user guides, pdf manuals, owners manuals, installation guides
Modify Date                     : 2016:04:28 16:48:07-07:00
Subject                         : Search through 700.000 manuals online & and download pdf manuals.
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : Provided By MANUALSLIB.COM - http://www.manualslib.com/
Description                     : Search through 700.000 manuals online & and download pdf manuals.
Title                           : ManualsLib - Makes it easy to find manuals online!
Creator Tool                    : pdftk 1.44 - www.pdftk.com
Metadata Date                   : 2016:04:28 16:48:07-07:00
Producer                        : itext-paulo-155 (itextpdf.sf.net-lowagie.com)
Document ID                     : uuid:45178617-aca8-5346-b80c-ad6ba141573d
Instance ID                     : uuid:c54b983b-6f67-3e4f-a761-8b4134f62374
Page Count                      : 24

EXIF Metadata provided by EXIF.tools

Hoover Concept One Manual 820242 ManualsLib Makes It Easy To Find Manuals Online! User

Navigation menu

Versions of this User Manual:

Views

Navigation