Hp Elitepad Mobile Pos G1 Solution Maintenance And Service Guide

2015-01-05

: Hp Hp-Elitepad-Mobile-Pos-G1-Solution-Maintenance-And-Service-Guide-201433 hp-elitepad-mobile-pos-g1-solution-maintenance-and-service-guide-201433 hp pdf

Open the PDF directly: View PDF .
Page Count: 120

Download
Open PDF In Browser	View PDF

HP ElitePad 1000 G2
Maintenance and Service Guide
IMPORTANT! This document is intended for
HP authorized service providers only.

© Copyright 2014 Hewlett-Packard
Development Company, L.P.
Bluetooth is a trademark owned by its
proprietor and used by Hewlett-Packard
Company under license. Intel is a U.S.
registered trademark of Intel Corporation.
Microsoft and Windows are U.S. registered
trademarks of Microsoft Corporation. SD
Logo is a trademark of its proprietor.
The information contained herein is subject
to change without notice. The only
warranties for HP products and services are
set forth in the express warranty statements
accompanying such products and services.
Nothing herein should be construed as
constituting an additional warranty. HP shall
not be liable for technical or editorial errors
or omissions contained herein.
First Edition: March 2014
Document Part Number: 741057-001
Product notice
This guide describes features that are
common to most models. Some features may
not be available on your computer.
Not all features are available in all editions
of Windows 8. This computer may require
upgraded and/or separately purchased
hardware, drivers, and/or software to take
full advantage of Windows 8 functionality.
See for http://www.microsoft.com details.
Software terms
By installing, copying, downloading, or
otherwise using any software product
preinstalled on this computer, you agree to
be bound by the terms of the HP End User
License Agreement (EULA). If you do not
accept these license terms, your sole remedy
is to return the entire unused product
(hardware and software) within 14 days for
a refund subject to the refund policy of your
place of purchase.
For any further information or to request a
full refund of the computer, please contact
your local point of sale (the seller).

Safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the device, do not
place the device directly on your lap or obstruct the device air vents. Use the device only on a hard, flat
surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface,
such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact the
skin or a soft surface, such as pillows or rugs or clothing, during operation. The device and the AC
adapter comply with the user-accessible surface temperature limits defined by the International
Standard for Safety of Information Technology Equipment (IEC 60950).

iii

Safety warning notice

Table of contents

1 Product description ........................................................................................................... 1
2 External component identification ..................................................................................... 4
Front ....................................................................................................................................... 4
Rear ....................................................................................................................................... 5
Top ........................................................................................................................................ 6
Bottom .................................................................................................................................... 7
3 Illustrated parts catalog .................................................................................................... 8
Service tag .............................................................................................................................. 8
Tablet major components .......................................................................................................... 9
Retail Jacket components ......................................................................................................... 12
Security Jacket components ..................................................................................................... 14
Adapter cables ...................................................................................................................... 15
Docking station and accessories .............................................................................................. 16
Miscellaneous parts ................................................................................................................ 17
Power components ................................................................................................................. 19
Sequential part number listing .................................................................................................. 20
4 Removal and replacement preliminary requirements ...................................................... 26
Tools required ....................................................................................................................... 26
Service considerations ............................................................................................................ 26
Plastic parts ............................................................................................................ 26
Cables and connectors ............................................................................................ 26
Grounding guidelines ............................................................................................................. 27
Electrostatic discharge damage ................................................................................. 27
Packaging and transporting guidelines ....................................................... 28
Workstation guidelines .............................................................. 28
5 Removal and replacement procedures ............................................................................ 30
Tablet component replacement procedures ................................................................................ 30

Display assembly .................................................................................................... 30
NFC antenna .......................................................................................................... 38
WWAN module ..................................................................................................... 39
WLAN module ........................................................................................................ 41
Microphones .......................................................................................................... 43
Rear-facing webcam ................................................................................................ 44
Power button board ................................................................................................. 45
Volume button board ............................................................................................... 47
Audio jack board .................................................................................................... 49
Vibrator module ...................................................................................................... 50
Battery ................................................................................................................... 51
System board ......................................................................................................... 53
Forward-facing webcam .......................................................................................... 57
Slot cover ............................................................................................................... 58
Docking connector cable .......................................................................................... 59
WLAN antenna ...................................................................................................... 61
WWAN/GPS auxiliary antenna ............................................................................... 63
Speakers ................................................................................................................ 65
Retail Jacket component replacement procedures ....................................................................... 67
Top cap ................................................................................................................. 67
Battery ................................................................................................................... 68
Front cover ............................................................................................................. 69
Bar code scanner module and Cable connector board ................................................ 73
Battery connector board ........................................................................................... 75
System board ......................................................................................................... 76
Credit card reader board ......................................................................................... 78
Credit card reader .................................................................................................. 80
Security Jacket component replacement procedures .................................................................... 82
Card reader cover and Top cap ............................................................................... 82
Front cover ............................................................................................................. 84
System board ......................................................................................................... 86
Docking connector cable .......................................................................................... 87
Card reader board .................................................................................................. 88
Fingerprint reader board .......................................................................................... 89
6 Computer Setup and HP PC Hardware Diagnostics (UEFI) ................................................ 91
Using Computer Setup ............................................................................................................ 91
Starting Computer Setup .......................................................................................... 91
Navigating and selecting in Computer Setup .............................................................. 92
Restoring factory settings in Computer Setup ............................................................... 92
Updating the BIOS .................................................................................................. 93

Determining the BIOS version .................................................................... 93
Downloading a BIOS Update ................................................................................... 93
Using HP PC Hardware Diagnostics (UEFI) ................................................................. 94
7 Specifications .................................................................................................................. 95
Tablet specifications ............................................................................................................... 95
8 Backup and recovery ...................................................................................................... 96
Backing up your information .................................................................................................... 96
Performing a system recovery .................................................................................................. 97
Using the Windows recovery tools ............................................................................ 97
Using f11 recovery tools .......................................................................................... 98
Changing the boot device order ............................................................................... 98
Using Windows Refresh or Windows Reset ................................................................ 99
9 Statement of Volatility .................................................................................................. 100
Non-volatile memory usage ................................................................................................... 102
Questions and answers ......................................................................................................... 105
10 Power cord set requirements ...................................................................................... 106
Requirements for all countries ................................................................................................ 106
Requirements for specific countries and regions ....................................................................... 107
11 Recycling .................................................................................................................... 108
Index ............................................................................................................................... 109

vii

viii

Product description

Category

Description

Security

Support for trusted platform module (TPM; Infineon TPM is SLB9656VQ1.2FW4.32)

Operating system

Preinstalled:
●

Microsoft® Windows® 8.1 ML 64-bit

●

Microsoft Windows 8.1 EM 64-bit

●

Microsoft Windows 8.1 CM 64-bit

●

Microsoft Windows 8.1 Professional 64-bit

●

Microsoft Windows 8.1 Professional 64-bit MSNA

●

Microsoft Windows 8.1 Professional 64-bit Retail Solutions

●

Microsoft Windows 8.1 SST 64-bit with Home and Student DPK

●

Microsoft Windows 8.1 SST 64-bit China with Home and Student DPK

●

Microsoft Windows 8.1 SST 64-bit without Home and Student DPK

●

Microsoft Windows 8.1 64-bit Embedded Industry

External component identification

Front

Item

Component

Description

(1)

WWAN antennas (2)* (select models only)

Send and receive wireless signals to communicate
with WWANs.

(2)

Front webcam

Records video and captures still photographs.
To use the webcam, tap the YouCam tile on the Start
screen, or swipe from the right edge of the touch screen
to display the charms, tap Search, and then tap the
search box. In the search box, type c, and then tap
CyberLink YouCam.

(3)

WLAN antennas (2)*

Chapter 2 External component identification

Send and receive wireless signals to communicate
with WLANs.

Item

Component

Description

(4)

Ambient light sensor

The ambient light sensor automatically adjusts the
display brightness based on the lighting conditions in
your environment.

(5)

Webcam status light (front)

On: The webcam is on.

(6)

Near Field Communications (NFC) tapping
area

Allows you to touch an NFC-compatible device to this
area to wirelessly connect and communicate with the
tablet and transfer data back and forth.

(7)

Windows button

Displays the Start screen.

*The antennas are not visible on the outside of the tablet. For optimal transmission, keep the areas immediately around the
antennas free from obstructions. To see wireless regulatory notices, see the section of the Regulatory, Safety, and Environmental
Notices that applies to your country or region. To access the user guides, tap the HP Support Assistant app on the Start
screen, tap My computer, and then tap User guides.

Rear

Item

Component

Description

(1)

Micro SD Card Reader/Micro SIM slot
access hole

Allows you to insert the end of a paper clip to open the
access door to insert or remove a micro SD card or micro
SIM module.

(2)

Memory card reader/Micro SIM slot

Reads optional micro memory cards that store, manage,
share, or access information. and supports an optional
wireless micro subscriber identity module (SIM) (select
models only).

Rear

Item

Component

Description

(3)

Rear webcam

Records video, captures still photographs, and allows
video conferences and online chat by means of streaming
video.
To use the webcam, tap the YouCam tile on the Start
screen, or swipe from the right edge of the touch screen
to display the charms, tap Search, and then tap the
search box. In the search box, type c, and then tap
CyberLink YouCam.

(4)

Volume up button

To increase speaker volume, press the top edge of
the button.

(5)

Volume down button

To decrease speaker volume, press the bottom edge of
the button.

(6)

Regulatory information

Displays regulatory information (select models only).

Item

Component

Description

(1)

Audio-out (headphone) jack/Audio-in
(microphone) jack

Produces sound when connected to optional powered
stereo speakers, headphones, earbuds, a headset, or
television audio. Also connects an optional headset
microphone.

Top

WARNING! To reduce the risk of personal injury,
adjust the volume before putting on headphones,
earbuds, or a headset. For additional safety information,
refer to the Regulatory, Safety, and Environmental
Notices. To access the user guides, tap the HP Support
Assistant app on the Start screen, tap My computer,
and then tap User guides.
NOTE: When a device is connected to the jack, the
computer speakers are disabled.
NOTE: Be sure that the device cable has a 4-conductor
connector that supports both audio-out (headphone) and
audio-in (microphone).

Chapter 2 External component identification

Item

Component

Description

(2)

Autorotate switch

When the tablet is on, slide the autorotate switch to lock
the autorotate feature of the display. To unlock the
autorotate feature, slide the switch again.
– or –
Swipe from the right edge of the touch screen to display
the charms, tap Settings, tap the screen icon, and then
tap the autorotate icon. To unlock the autorotate feature,
tap the autorotate icon again.

(3)

Integrated microphones (2)

Record sound.

(4)

Power button

●

When the tablet is off, press the button to turn on
the tablet.

●

When the tablet is on, press the button briefly to
initiate Sleep.

●

When the tablet is in the Sleep state, press the
button briefly to exit Sleep.

CAUTION: Pressing and holding down the power
button will result in the loss of unsaved information.
If the tablet has stopped responding and Windows
shutdown procedures are ineffective, press and hold the
power button for at least 5 seconds to turn off the tablet.
Swipe from the right edge of the touch screen to display
the charms, tap Search, and then tap the search box. In
the search box, type power, tap Power and sleep
settings, and then select Power and sleep from the
list of applications.

Bottom

Item

Component

Description

(1)

Speakers (2)

Produce sound.

(2)

Product and regulatory information

Displays product and regulatory information
(select models only).

(3)

Docking connector

Connects an AC adapter or an optional docking device.

Bottom

Illustrated parts catalog

NOTE: HP continually improves and changes product parts. For complete and current information on
supported parts for your computer, go to http://partsurfer.hp.com, select your country or region, and
then follow the on-screen instructions.

Service tag
When ordering parts or requesting information, provide the tablet serial number and model number
provided on the service tag.

Item

Description

Function

(1)

Warranty period

This number describes the duration of the warranty
period for the tablet.

(2)

Model description

This is the alphanumeric identifier used to locate
documents, drivers, and support for the tablet.

(3)

Product name

This is the product name affixed to the front of
the tablet.

(4)

Serial number (s/n)

This is an alphanumeric identifier that is unique to
each product.

Chapter 3 Illustrated parts catalog

Tablet major components

Item

Component

Spare part number

(1)

Display assembly (10.1-in., WUXGA (1900×1200), UWVA, 50% CG, 400-nit,
active pen and MultiTouch capacitive digitizer, chemically-strengthened glass with
anti-smudge; includes display panel, display LVDS cable, TouchScreen cable, and
display panel support rubber)

747658-001

Display Cable Kit, includes:

747625-001

(2a)

TouchScreen cable

(2b)

Display LVDS cable

(3)

NFC antenna (includes double-sided adhesive)

747633-001

Button Kit, includes:

747634-001

(4a)

Power button actuator

(4b)

Volume button actuator

Tablet major components

Item

Component

(4c)

Autorotate switch actuator

(4d)

Slot cover hardware (slot cover, retention bracket, spring bracket)

(4e)

Docking connector bracket
Webcam/Microphone Kit, includes:

(5a)

Left microphone

(5b)

Right microphone

(6a)

Rear-facing webcam

(6b)

Front-facing webcam

(7)

Power button board (includes cable)

Spare part number

762828-001

For use only on tablet models equipped with the Windows 8 Professional
operating system

753976-601

For use only on tablet models equipped with the Windows 8 Standard
operating system

753976-501

For use only on tablet models equipped with a non-Windows 8 operating system

753976-001

(8)

Volume button board (includes bracket and cable)

759031-001

(9)

WWAN module:
HP hs3110 HSPA+ Mobile Broadband Module

748599-005

HP lt4111 LTE/EV-DO/HSPA+ Gobi 4G Module

704030-005

HP lt4112 LTE/HSPA+ Gobi 4G Module

740011-005

HP lt4225 LTE/EV-DO Gobi 4G Module

736676-005

HP lt4226 LTE/HSPA+ Gobi 4G Module

736675-005

(10)

2-cell, 30-Wh, 4.0-Ah, Li-ion battery (includes battery cable and WWAN/GPS
main transceiver and antenna cable)

728558-005

(11)

System board equipped with an Intel Atom z3795 quad core 1.60-GHz processor (burst up to 2.39-GHz; 2.0MB L2 cache), and 4096-MB of system memory (includes processor, memory, and eMMC)

(12)

Equipped with 128-GB of eMMC primary storage

753741-001

Equipped with 64-GB of eMMC primary storage

753740-001

Audio jack board (includes audio jack and cable)

747627-001

Antenna Kit, includes:

(13)

WWAN/GPS auxiliary antenna (includes auxiliary antenna cable and transceiver)

(14)

WLAN antenna (includes WLAN main and auxiliary antenna cables and transceivers)
For use only in European countries and regions

767884-001

For use only in Japan

767885-001

For use only in the United States

767883-001

Chapter 3 Illustrated parts catalog

Item

Component

Spare part number

(15)

Broadcom BCM43241 802.11abgn 2x2 Wi-Fi + BT 4.0 Combo Adapter

723677-005

(16)

Vibrator module (includes cable, double-sided adhesive, plastic cover)

747630-001

(17)

Docking connector cable (includes cable and double-sided adhesive)

747631-001

(18)

Speakers (include left and right speakers and cables)

747629-001

(19)

Bottom case (includes the power button actuator and the slot cover and brackets)

747628-001

Tablet major components

Retail Jacket components

Item

Description

Spare part number

(1)

Top cap (includes 4 captive screws, secured by C-rings)

744025-001

(2)

Battery (2-cell, 21-Wh, 2.96-Ah, Li-ion)

687946-001

(3)

Battery bay space saver

742440-001

(4)

Front cover adhesive liner (included with front cover, spare part number 744030-001)

(5)

Front cover (includes bar code scanner lens and adhesive liner)

744030-001

(6)

Bar code scanner module

744037-001

(7)

Cable connector board

744034-001

Cable Kit, includes:

744031-001

(8a)

Bar code scanner module cable

(8b)

Cable connector board cable

(8c)

Credit card reader board/left board cable

Chapter 3 Illustrated parts catalog

Item

Description

Spare part number

(8d)

Credit card reader board/right board cable

(9)

Left-side credit card reader board

744027-001

(10)

Right-side credit card reader board

744028-001

(11)

Credit card reader (includes cable)

744026-001

(12)

Battery connector board (includes cable)

744033-001

(13)

System board (includes docking connector and USB port)

744032-001

(14)

Rear cover

744029-001

Retail Jacket equipped with battery (not illustrated)

742441-001

Retail Jacket equipped with a battery bay space saver (not illustrated)

742442-001

Handle (not illustrated)

742439-001

Miscellaneous Rocker Button Mounting Kit (not illustrated)

744038-001

Rubber Kit for use only on the Retail Jacket (not illustrated)

742443-001

Screw Kit for use only on the Retail Jacket (not illustrated)

744035-001

Retail Jacket components

Security Jacket components

Item

Description

Spare part number

(1)

Top cap (includes rubber trim)

744047-001

(2)

Card reader cover

744039-001

(3)

Front cover

744048-001

(4)

Rear cover (includes top cap release latch assembly)

744041-001

(5)

Fingerprint reader board

744042-001

(6)

Card reader board

744043-001

(7)

System board

744044-001

Cables/Connectors Kit, includes:

744045-001

(8a)

Fingerprint reader board cable

(8b)

Card reader board cable

(8c)

Docking connector cable
Security Jacket equipped with a card reader and a fingerprint reader
(not illustrated)

742446-001

Security Jacket equipped with a card reader (not illustrated)

742444-001

Chapter 3 Illustrated parts catalog

Item

Description

Spare part number

Rubber Kit for use only on the Security Jacket (not illustrated)

744040-001

Screw Kit for use only on the Security Jacket (not illustrated)

744046-001

Adapter cables

Item

Description

Spare part number

(1)

HDMI/VGA adapter cable

695551-001

(2)

Ethernet adapter cable

695555-001

(3)

Serial adapter cable

695556-001

(4)

HP Smart AC adapter cable

695553-001

(5)

USB adapter cable

695552-001

(6)

Card Reader adapter

695554-001

Adapter cables

Docking station and accessories

Item

Description

Spare part number

(1)

Docking station

708621-001

(2)

40-W HP Smart AC adapter (RC, V, 3-wire)

693717-001

(3)

Power cord (3-pin, black, 1.83-m):
For use in Argentina

490371-D01

For use in Australia

490371-011

For use in Brazil

490371-202

For use in Europe

490371-021

For use in India

490371-D61

For use in Israel

490371-BB1

For use in Italy

490371-061

For use in Japan

490371-291

For use in North America

490371-001

For use in the People's Republic of China

490371-AA1

For use in South Africa

490371-AR1

For use in South Korea

490371-AD1

For use in Switzerland

490371-111

Chapter 3 Illustrated parts catalog

Item

Description

Spare part number

For use in Taiwan

490371-AB1

For use in the United Kingdom and Singapore

490371-031

Miscellaneous parts
Component

Spare part number

Carrying case:
HP ElitePad dockable case

742720-001

HP ElitePad rugged carrying case

708772-001

HP ElitePad Service Tool (includes suction cup)

714222-001

HP ElitePad suction cup

714223-001

HP executive tablet pen

716117-001

Jacket:
Slate jacket with battery slot (includes battery)

709462-001

Slate jacket without battery slot

714297-001

Jacket keyboard:
For use in Belgium

724301-A41

For use in Brazil

724301-201

For use in Bulgaria

724301-261

For use in Canada

724301-DB1

For use in the Czech Republic and Slovakia

724301-FL1

For use in Denmark

724301-081

For use in France

724301-051

For use in Germany

724301-041

For use in Greece

724301-151

For use in Hungary

724301-211

For use in Iceland

724301-DD1

For use in India

724301-D61

For use in Israel

724301-BB1

For use in Italy

724301-061

For use in Japan

724301-291

For use in Latin America

724301-161

Miscellaneous parts

Component

Spare part number

For use in the Netherlands

724301-B31

For use in Norway

724301-091

For use in Northwest Africa

724301-FP1

For use in Portugal

724301-131

For use in Romania

724301-271

For use in Russia

724301-251

For use in Saudi Arabia

724301-171

For use in Slovenia

724301-BA1

For use in South Korea

724301-AD1

For use in Spain

724301-071

For use in Sweden and Finland

724301-B71

For use in Switzerland

724301-BG1

For use in Taiwan

724301-AB1

For use in Thailand

724301-281

For use in Turkey

724301-141

For use in the United Kingdom and Singapore

724301-031

For use in the United States

724301-001

Screw Kit for use only with the tablet

709461-001

Chapter 3 Illustrated parts catalog

Power components

Item

Component

Spare part number

(1)

10-W AC adapter for use only on the HP ElitePad 1000 G2 (RC, V, 3-wire, wallmount)

686120-001

(2)

Duck head power adapter:

(3)

For use in Argentina

755184-D01

For use in Australia

755184-011

For use in Brazil

755184-201

For use in Denmark

755184-081

For use in Europe

755184-021

For use in India

755184-D61

For use in Israel

755184-BB1

For use in Italy

755184-061

For use in the People's Republic of China

755184-371

For use in South Africa

755184-AR1

For use in Switzerland

755184-BG1

For use in the United Kingdom and Singapore

755184-031

For use in the United States

755184-001

Power cord (3-pin, black, 1.83-m):
For use in Argentina

490371-D01

For use in Australia

490371-011

For use in Brazil

490371-202

Power components

Item

Component

Spare part number

For use in Europe

490371-021

For use in India

490371-D61

For use in Israel

490371-BB1

For use in Italy

490371-061

For use in Japan

490371-291

For use in North America

490371-001

For use in the People's Republic of China

490371-AA1

For use in South Africa

490371-AR1

For use in South Korea

490371-AD1

For use in Switzerland

490371-111

For use in Taiwan

490371-AB1

For use in the United Kingdom and Singapore

490371-031

Card Reader Cover Kit (not illustrated)

747632-001

HP Mobile Connect SIM (not illustrated)

714749-001

Screw Kit for use only on the HP ElitePad 1000 G2 (not illustrated)

753735-001

Tape Support Kit

762827-001

Sequential part number listing

Spare part number

Description

490371-001

Power cord for use in North America (3-pin, black, 1.83-m)

490371-011

Power cord for use in Australia (3-pin, black, 1.83-m)

490371-021

Power cord for use in Europe (3-pin, black, 1.83-m)

490371-031

Power cord for use in the United Kingdom and Singapore (3-pin, black, 1.83-m)

490371-061

Power cord for use in Italy (3-pin, black, 1.83-m)

490371-111

Power cord for use in Switzerland (3-pin, black, 1.83-m)

490371-202

Power cord for use in Brazil (3-pin, black, 1.83-m)

490371-291

Power cord for use in Japan (3-pin, black, 1.83-m)

490371-AA1

Power cord for use in the People's Republic of China (3-pin, black, 1.83-m)

490371-AB1

Power cord for use in South Korea (3-pin, black, 1.83-m)

490371-AD1

Power cord for use in Taiwan (3-pin, black, 1.83-m)

490371-AR1

Power cord for use in South Africa (3-pin, black, 1.83-m)

Chapter 3 Illustrated parts catalog

Spare part number

Description

490371-BB1

Power cord for use in Israel (3-pin, black, 1.83-m)

490371-D01

Power cord for use in Argentina (3-pin, black, 1.83-m)

490371-D61

Power cord for use in India (3-pin, black, 1.83-m)

686120-001

10-W AC adapter (RC, V, 3-wire, wall-mount)

687946-001

2-cell, 21-Wh, 2.96-Ah, Li-ion battery for use only on the Retail Jacket

693717-001

40-W HP Smart AC adapter for use only with the docking station (RC, V, 3-wire)

695551-001

HDMI/VGA adapter cable

695552-001

USB adapter cable

695553-001

HP Smart AC adapter cable

695554-001

Card Reader adapter

695555-001

Ethernet adapter cable

695556-001

Serial adapter cable

704030-001

HP lt4111 LTE/EV-DO/HSPA+ Gobi 4G Module

708621-001

Docking station

708772-001

Rugged carrying case

709462-001

Slate jacket with battery slot (includes battery)

714222-001

HP ElitePad Service Tool (includes suction cup)

714223-001

HP ElitePad suction cup

714297-001

Slate jacket without battery slot

714749-001

HP Mobile Connect SIM

723677-005

Broadcom BCM43241 802.11abgn 2x2 Wi-Fi + BT 4.0 Combo Adapter

724301-001

Jacket keyboard for use in the United States

724301-031

Jacket keyboard for use in the United Kingdom and Singapore

724301-041

Jacket keyboard for use in Germany

724301-051

Jacket keyboard for use in France

724301-061

Jacket keyboard for use in Italy

724301-071

Jacket keyboard for use in Spain

724301-081

Jacket keyboard for use in Denmark

724301-091

Jacket keyboard for use in Norway

724301-131

Jacket keyboard for use in Portugal

724301-141

Jacket keyboard for use in Turkey

724301-151

Jacket keyboard for use in Greece

Sequential part number listing

Spare part number

Description

724301-161

Jacket keyboard for use in Latin America

724301-171

Jacket keyboard for use in Saudi Arabia

724301-201

Jacket keyboard for use in Brazil

724301-211

Jacket keyboard for use in Hungary

724301-251

Jacket keyboard for use in Russia

724301-261

Jacket keyboard for use in Bulgaria

724301-271

Jacket keyboard for use in Romania

724301-281

Jacket keyboard for use in Thailand

724301-291

Jacket keyboard for use in Japan

724301-A41

Jacket keyboard for use in Belgium

724301-AB1

Jacket keyboard for use in Taiwan

724301-AD1

Jacket keyboard for use in South Korea

724301-B31

Jacket keyboard for use in the Netherlands

724301-B71

Jacket keyboard for use in Sweden and Finland

724301-BA1

Jacket keyboard for use in Slovenia

724301-BB1

Jacket keyboard for use in Israel

724301-BG1

Jacket keyboard for use in Switzerland

724301-D61

Jacket keyboard for use in India

724301-DB1

Jacket keyboard for use in Canada

724301-DD1

Jacket keyboard for use in Iceland

724301-FL1

Jacket keyboard for use in the Czech Republic and Slovakia

724301-FP1

Jacket keyboard for use in Northwest Africa

728558-005

2-cell, 30-Wh, 4.0-Ah, Li-ion battery for use only on the HP ElitePad 1000 G2 tablet (includes
battery cable and WWAN/GPS main transceiver and antenna cable)

732251-001

Digital pen tethers (10)

736675-005

HP lt4226 LTE/HSPA+ Gobi 4G Module

736676-005

HP lt4225 LTE/EV-DO Gobi 4G Module

736679-001

HP ElitePad Jacket cover

739321-001

HP ElitePad USB3 adapter

740011-005

HP lt4112 LTE/HSPA+ Gobi 4G Module

742439-001

Retail Jacket handle

742440-001

Retail Jacket battery bay space saver

742441-001

Retail Jacket with battery

Chapter 3 Illustrated parts catalog

Spare part number

Description

742442-001

Retail Jacket with battery bay space saver

742443-001

Retail Jacket Rubber Kit

742444-001

Security Jacket with screws

742446-001

Security Jacket with fingerprint reader and screws

742720-001

HP ElitePad dockable case

744025-001

Retail Jacket top cap (includes 4 captive screws, secured by C-rings)

744026-001

Retail Jacket credit card reader (includes cable)

744027-001

Retail Jacket left-side credit card reader board

744028-001

Retail Jacket right-side credit card reader board

744029-001

Retail Jacket rear cover

744030-001

Retail Jacket front cover (includes bar code scanner lens and adhesive liner)

744031-001

Retail Jacket Cable Kit

744032-001

Retail Jacket system board (includes docking connector and USB port)

744033-001

Retail Jacket battery connector board (includes cable)

744034-001

Retail Jacket cable connector board

744035-001

Retail Jacket Screw Kit

744037-001

Retail Jacket bar code scanner module

744038-001

Retail Jacket Miscellaneous Rocker Button/Mount Kit

744039-001

Security Jacket card reader cover

744040-001

Security Jacket Rubber Kit

744041-001

Security Jacket rear cover (includes top cap release latch assembly)

744042-001

Security Jacket fingerprint reader

744043-001

Security Jacket card reader board

744044-001

Security Jacket system board

744045-001

Security Jacket Cables/Connectors Kit

744046-001

Security Jacket Screw Kit

744047-001

Security Jacket top cap (includes rubber trim)

744048-001

Security Jacket front cover

745882-001

Productivity Jacket Cable Retainer Kit

747625-001

Display Cable Kit (includes the display LVDS cable and the TouchScreen cable)

747627-001

Audio jack board (includes audio jack and cable)

747628-001

Bottom case (includes the power button actuator and the slot cover and brackets)

Sequential part number listing

Spare part number

Description

747629-001

Speakers (include left and right speakers and cables

747630-001

Vibrator module (includes cable, double-sided adhesive, plastic cover)

747631-001

Docking connector cable (includes double-sided adhesive)

747632-001

Smart Card Reader Cover Kit

747633-001

NFC antenna (includes double-sided adhesive)

747634-001

Button Kit (includes autorotate switch actuator, docking connector bracket, power button actuator,
slot cover hardware, and volume button actuator)

747658-001

Display assembly (10.1-in., WUXGA (1900×1200), UWVA, 50% CG, 400-nit, active pen and
MultiTouch capacitive digitizer, chemically-strengthened glass with anti-smudge; includes display
panel, display LVDS cable, TouchScreen cable, and display panel support rubber)

748599-005

HP hs3110 HSPA+ Mobile Broadband Module

751285-001

HP Executive Tablet pen

753735-001

Screw Kit for use only on the HP ElitePad 1000 G2

753740-001

System board equipped with an Intel Atom z3795 quad core 1.60-GHz processor (burst up to
2.39-GHz; 2.0-MB L2 cache), 4096-MB of system memory, and 64-GB of eMMC primary storage
(includes processor, memory, and eMMC)

753741-001

System board equipped with an Intel Atom z3795 quad core 1.60-GHz processor (burst up to
2.39-GHz; 2.0-MB L2 cache), 4096-MB of system memory, and 128-GB of eMMC primary storage
(includes processor, memory, and eMMC)

753976-001

Power button board for use only on tablet models equipped with a non-Windows 8
operating system

753976-501

Power button board for use only on tablet models equipped with the Windows 8 Standard
operating system

753976-601

Power button board for use only on tablet models equipped with the Windows 8 Professional
operating system

755184-001

Duck head power adapter for use only in the United States

755184-011

Duck head power adapter for use only in Australia

755184-021

Duck head power adapter for use only in Europe

755184-031

Duck head power adapter for use only in the United Kingdom and Singapore

755184-061

Duck head power adapter for use only in the Italy

755184-081

Duck head power adapter for use only in the Denmark

755184-201

Duck head power adapter for use only in Brazil

755184-371

Duck head power adapter for use only in the People's Republic of China

755184-AR1

Duck head power adapter for use only in South Africa

755184-BB1

Duck head power adapter for use only in Israel

755184-BG1

Duck head power adapter for use only in Switzerland

755184-D01

Duck head power adapter for use only in Argentina

Chapter 3 Illustrated parts catalog

Spare part number

Description

755184-D61

Duck head power adapter for use only in India

756037-001

Security Jacket cover

759031-001

Volume button board (includes bracket and cable)

762827-001

Tape Support Kit

762828-001

Webcam/Microphone Kit (includes forward-facing and rear-facing webcams and microphones)

767882-001

3G antenna

767883-001

Antenna Kit for use only in the United States (includes WWAN/GPS auxiliary antenna cable and
transceiver and WLAN main and auxiliary antenna cables and transceivers)

767884-001

Antenna Kit for use only in European countries and regions (includes WWAN/GPS auxiliary
antenna cable and transceiver and WLAN main and auxiliary antenna cables and transceivers)

767885-001

Antenna Kit for use only in Japan (includes WWAN/GPS auxiliary antenna cable and transceiver
and WLAN main and auxiliary antenna cables and transceivers)

Sequential part number listing

Removal and replacement
preliminary requirements

Tools required
You will need the following tools to complete the removal and replacement procedures:
●

Magnetic screw driver

●

Phillips P0 screw driver

●

Plastic case utility tool

Service considerations
The following sections include some of the considerations that you must keep in mind during
disassembly and assembly procedures.
NOTE: As you remove each subassembly from the tablet, place the subassembly (and all
accompanying screws) away from the work area to prevent damage.

Plastic parts
CAUTION: Using excessive force during disassembly and reassembly can damage plastic parts.
Use care when handling the plastic parts. Apply pressure only at the points designated in the
maintenance instructions.

Cables and connectors
CAUTION: When servicing the tablet, be sure that cables are placed in their proper locations during
the reassembly process. Improper cable placement can damage the tablet.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat
or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In
all cases, avoid bending, twisting, or tearing cables. Be sure that cables are routed in such a way that
they cannot be caught or snagged by parts being removed or replaced. Handle flex cables with
extreme care; these cables tear easily.

Chapter 4 Removal and replacement preliminary requirements

Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure
determine the degree of sensitivity. Networks built into many integrated circuits provide some
protection, but in many cases, ESD contains enough power to alter device parameters or melt
silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a
normal cycle. Or the device may function normally for a while, then degrade in the internal layers,
reducing its life expectancy.
CAUTION: To prevent damage to the tablet when you are removing or installing internal
components, observe these precautions:
Keep components in their electrostatic-safe containers until you are ready to install them.
Before touching an electronic component, discharge static electricity by using the guidelines described
in this section.
Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
If you remove a component, place it in an electrostatic-safe container.
The following table shows how humidity affects the electrostatic voltage levels generated by
different activities.
CAUTION: A product can be degraded by as little as 700 V.
Typical electrostatic voltage levels
Relative humidity
Event

10%

40%

55%

Walking across carpet

35,000 V

15,000 V

7,500 V

Walking across vinyl floor

12,000 V

5,000 V

3,000 V

Motions of bench worker

6,000 V

800 V

400 V

Removing DIPS from plastic tube

2,000 V

700 V

400 V

Removing DIPS from vinyl tray

11,500 V

4,000 V

2,000 V

Removing DIPS from Styrofoam

14,500 V

5,000 V

3,500 V

Removing bubble pack from PCB

26,500 V

20,000 V

7,000 V

Packing PCBs in foam-lined box

21,000 V

11,000 V

5,000 V

Grounding guidelines

Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
●

To avoid hand contact, transport products in static-safe tubes, bags, or boxes.

●

Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.

●

Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.

●

Place items on a grounded surface before removing items from their containers.

●

Always be properly grounded when touching a component or assembly.

●

Store reusable ESD-sensitive parts from assemblies in protective packaging or
nonconductive foam.

●

Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that
mechanized equipment used for moving materials is wired to ground and that proper materials
are selected to avoid static charging. When grounding is not possible, use an ionizer to dissipate
electric charges.

Workstation guidelines
Follow these grounding workstation guidelines:

●

Cover the workstation with approved static-shielding material.

●

Use a wrist strap connected to a properly grounded work surface and use properly grounded tools
and equipment.

●

Use conductive field service tools, such as cutters, screw drivers, and vacuums.

●

When fixtures must directly contact dissipative surfaces, use fixtures made only of staticsafe materials.

●

Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids
and Styrofoam.

●

Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle
these items only at static-free workstations.

●

Avoid contact with pins, leads, or circuitry.

●

Turn off power and input signals before inserting or removing connectors or test equipment.

Chapter 4 Removal and replacement preliminary requirements

Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
●

When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps
with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground,
wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors,
use alligator clips to connect a wrist strap.

●

When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps)
can be used at standing workstations and are compatible with most types of shoes or boots. On
conductive floors or dissipative floor mats, use foot straps on both feet with a minimum of one
megohm resistance between the operator and ground. To be effective, the conductive must be
worn in contact with the skin.

The following grounding equipment is recommended to prevent electrostatic damage:
●

Antistatic tape

●

Antistatic smocks, aprons, and sleeve protectors

●

Conductive bins and other assembly or soldering aids

●

Nonconductive foam

●

Conductive tabletop workstations with ground cords of one megohm resistance

●

Static-dissipative tables or floor mats with hard ties to the ground

●

Field service kits

●

Static awareness labels

●

Material-handling packages

●

Nonconductive plastic bags, tubes, or boxes

●

Metal tote boxes

●

Electrostatic voltage levels and protective materials

The following table lists the shielding protection provided by antistatic bags and floor mats.
Material

Use

Voltage protection level

Antistatic plastics

Bags

1,500 V

Carbon-loaded plastic

Floor mats

7,500 V

Metallized laminate

Floor mats

5,000 V

Grounding guidelines

Removal and replacement
procedures

CAUTION: Components described in this chapter should only be accessed by an authorized service
provider. Accessing these parts can damage the computer or void the warranty.
NOTE: HP continually improves and changes product parts. For complete and current information on
supported parts for your computer, go to http://partsurfer.hp.com, select your country or region, and
then follow the on-screen instructions.

Tablet component replacement procedures
This chapter provides removal and replacement procedures for Authorized Service Provider only parts.
There are as many as 34 screws that must be removed, replaced, and/or loosened when servicing the
tablet. Make special note of each screw size and location during removal and replacement.

Display assembly
Description

Spare part number

10.1-in., WUXGA (1900×1200), UWVA, 50% CG, 400-nit, active pen and MultiTouch
capacitive digitizer, chemically-strengthened glass with anti-smudge; includes display panel,
display LVDS cable, TouchScreen cable, and display panel support rubber

747658-001

Before disassembling the tablet, follow these steps:

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet.

Disconnect all external devices from the tablet.

Chapter 5 Removal and replacement procedures

Remove the display assembly:
1.

Remove the two Phillips PM1.4×3.2 screws that secure the display assembly to the tablet.

Place the HP ElitePad Service Tool on a flat, sturdy surface.
The HP ElitePad Service Tool is available using spare part number 714222-001.

Move the HP ElitePad Service Tool retention bar (1) to the left until the notch (2) in the retention
bar allows the retention gate to open.

Tablet component replacement procedures

Open the retention gate (3).

Place the tablet on the service tool and slide it (1) forward until the tablet docking connector
engages with the service tool docking connector (2).

Chapter 5 Removal and replacement procedures

Close the retention gate (1) and release the retention bar (2) to secure the tablet in the
service tool.

Place the suction cup (1) on the lower right corner of the tablet display glass, making sure to
place the suction cup inside the edges of the border (2) of the display glass.
The suction cup is available using spare part number 714223-001.

Raise the suction cup handle (3).

Tablet component replacement procedures

Lock the two suction cup handles together (4).
CAUTION: Do not lift the right edge of the display assembly more than ¼-inch from the tablet
when releasing the display assembly. Failure to follow this caution can result in damage to the
tablet components.

10. Firmly lift up on the suction cup to release the right side of the display assembly approximately ¼inch from the tablet.

11. Move the retention bar (1) until the notch in the retention bar allows the retention gate to open.
34

Chapter 5 Removal and replacement procedures

12. Open the retention gate (2).
13. Slide the tablet out of the service tool (3).

14. Disconnect the suction cup handles (1).
15. Lower the suction cup handle (2).
16. Remove the suction cup (3).

17. Slide the display assembly (1) to the left until the display assembly cables and connectors
are accessible.
18. Release the zero insertion force (ZIF) connector (2) to which the TouchScreen cable is attached,
and then disconnect the TouchScreen cable (3) from the system board.

Tablet component replacement procedures

19. Release the ZIF connector (4) to which the LVDS cable is attached, and then disconnect the LVDS
cable (5) from the system board.

20. Remove the display assembly and cables.
21. If it is necessary to replace the display assembly cables:

Turn the display assembly upside down, with the bottom toward you.

Detach the TouchScreen cable (1) from the surface of the display assembly. (The
TouchScreen cable is attached to the display assembly with double-sided adhesive.)

Release the ZIF connector (2) to which the TouchScreen cable is attached, and then
disconnect the TouchScreen cable (3) from the display assembly.

Detach the display LVDS cable (4) from the surface of the display assembly. (The display
LVDS cable is attached to the display assembly with double-sided adhesive.)

Chapter 5 Removal and replacement procedures

Release the ZIF connector (5) to which the display LVDS cable is attached, and then
disconnect the display LVDS cable (6) from the display assembly.
The TouchScreen and display LVDS cables are included in the Display Cable Kit, spare part
number 718758-001.

To install the display assembly:
1.

Reconnect the display LVDS and TouchScreen cables to the respective ZIF connectors on the
display assembly.

Reconnect the display LVDS and TouchScreen cables to the respective ZIF connectors on the
system board.

Toe the left side of the display assembly into the left side of the bottom case.

Swing the right side of the display assembly down into the right side of the bottom case.

Firmly press all edges of the display assembly surface to ensure it is fully engaged with the
bottom case.

Tablet component replacement procedures

NFC antenna
Description

Spare part number

NFC antenna

747633-001

Before removing the NFC antenna, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet.

Disconnect all external devices from the tablet.

Remove the display assembly (see Display assembly on page 30).

Remove the NFC antenna:
1.

Release the ZIF connector (1) to which the NFC antenna cable is attached, and then disconnect
the NFC antenna cable from the system board.

Detach the NFC antenna (2) from the surface of the system board. (The NFC antenna is attached
to the system board with double-sided adhesive.)

Remove the NFC antenna (3).

Reverse this procedure to install the NFC antenna.

Chapter 5 Removal and replacement procedures

WWAN module
Description

Spare part number

HP hs3110 HSPA+ Mobile Broadband Module

748599-005

HP lt4111 LTE/EV-DO/HSPA+ Gobi 4G Module

704030-005

HP lt4112 LTE/HSPA+ Gobi 4G Module

740011-005

HP lt4225 LTE/EV-DO Gobi 4G Module

736676-005

HP lt4226 LTE/HSPA+ Gobi 4G Module

736675-005

Before removing the WWAN module, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet.

Disconnect all external devices from the tablet.

Remove the display assembly (see Display assembly on page 30).

Remove the NFC antenna (see NFC antenna on page 38).

Remove the WWAN module:
1.

Release the grounding tape (1) that secures the WWAN module to the system board.

Disconnect the WWAN antenna cables (2) from the terminals on the WWAN module.
NOTE: The WWAN antenna cable labeled “5” connects to the WWAN module “MAIN”
terminal labeled “5”. The WWAN antenna cable labeled “6” connects to the WWAN module
“AUX/GPS” terminal labeled “6”.

Remove the Phillips PM1.3×1.5 broad head screw (3) that secures the WWAN module to the
bottom cover.

Tablet component replacement procedures

Remove the WWAN module (4) by sliding it away from the socket on the system board.

NOTE: If the WWAN antenna cables are not connected to the terminals on the WWAN
module, protective sleeves should be installed on the antenna connectors, as shown in the
following illustration.

Reverse this procedure to install the WWAN module.

Chapter 5 Removal and replacement procedures

WLAN module
Description

Spare part number

Broadcom BCM43241 802.11abgn 2x2 Wi-Fi + BT 4.0 Combo Adapter

723677-005

Before removing the WLAN module, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet.

Disconnect all external devices from the tablet.

Remove the display assembly (see Display assembly on page 30).

Remove the NFC antenna (see NFC antenna on page 38).

Remove the WLAN module:
1.

Release the ZIF connector (1) to which the WLAN ribbon cable is attached, and then disconnect
the WLAN ribbon cable from the system board.

Disconnect the WLAN antenna cables (2) from the terminals on the WLAN module.
NOTE: The WLAN antenna cable labeled “1” connects to the WLAN module “MAIN” terminal
labeled “1”. The WLAN antenna cable labeled “2” connects to the WLAN module “AUX”
terminal labeled “2”.

Release the shielding (3) to gain access to the bottom screw that secures the WLAN module to the
bottom cover.

Remove the two Phillips PM1.3×2.0 screws (4) that secure the WLAN module to the bottom cover.

Tablet component replacement procedures

Remove the WLAN module (5).

NOTE: If the WLAN antenna cables are not connected to the terminals on the WLAN module,
protective sleeves should be installed on the antenna connectors, as shown in the
following illustration.

Reverse this procedure to install the WLAN module.

Chapter 5 Removal and replacement procedures

Microphones
NOTE: The microphones are included in the Webcam/Microphone Kit, spare part number
762828-001.
Before removing the microphones, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet.

Disconnect all external devices from the tablet.

Remove the display assembly (see Display assembly on page 30).

Remove the NFC antenna (see NFC antenna on page 38).

Remove the microphones:
1.

Detach the tape (1) that secures the left microphone cable to the battery.

Disconnect the left microphone cable (2) from the power button board.

Release the left microphone (3) from the molding built into the bottom cover.

Disconnect the right microphone cable (4) from the system board.

Release the right microphone (5) from the molding built into the bottom cover.

Remove the microphones and cables.

Reverse this procedure to install the microphones.

Tablet component replacement procedures

Rear-facing webcam
NOTE: The rear-facing webcam is included in the Webcam/Microphone Kit, spare part number
762828-001.
Before removing the rear-facing webcam, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet.

Disconnect all external devices from the tablet.

Remove the display assembly (see Display assembly on page 30).

Remove the NFC antenna (see NFC antenna on page 38).

Remove the rear-facing webcam:
1.

Disconnect the rear-facing webcam cable (1) from the power button board.

Release the rear-facing webcam (2) from the molding built into the bottom cover.

Remove the rear-facing webcam (3) and cable.

Reverse this procedure to install the rear-facing webcam.

Chapter 5 Removal and replacement procedures

Power button board
Description

Spare part number

For use only on computer models equipped with the Windows 8 Professional operating system

753976-601

For use only on computer models equipped with the Windows 8 Standard operating system

753976-501

For use only on computer models equipped with a non-Windows 8 operating system

753976-001

Before removing the power button board, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet.

Disconnect all external devices from the tablet.

Remove the display assembly (see Display assembly on page 30).

Remove the NFC antenna (see NFC antenna on page 38).

Disconnect the left microphone cable from the power button board (see Microphones
on page 43).

Disconnect the rear-facing webcam cable from the power button board (see Rear-facing webcam
on page 44).

Remove the power button board:
1.

Disconnect the volume button board cable (1) from the power button board.

Release the support strip (2) that secures the WWAN antenna transceiver to the battery.

Release the support strip (3) that secures the power button board cable to the system board.

Release the ZIF connector (4) to which the power button board cable is attached, and then
disconnect the power button board cable from the system board.

Tablet component replacement procedures

Detach the power button board cable (5) from the surface of the battery. (The power button board
cable is attached to the battery with double-sided adhesive.)

Remove the Phillips PM1.3×2.0 broad head screw (1) and the Phillips PM1.3×2.0 screw (2) that
secure the power button board to the bottom cover.

Remove the power button board (3) and cable.

NOTE: In the process of removing the power button board, the power button actuator may be
accidentally dislodged from the bottom cover. To replace the power button actuator, refer to the
following illustration.
The power button actuator is included in the Button Kit, spare part number 747634-001.

Chapter 5 Removal and replacement procedures

Reverse this procedure to install the power button board.

Volume button board
Description

Spare part number

Volume button board (includes bracket and cable)

759031-001

Before removing the volume button board, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet.

Disconnect all external devices from the tablet.

Remove the display assembly (see Display assembly on page 30).

Remove the NFC antenna (see NFC antenna on page 38).

Remove the volume button board:
1.

Disconnect the volume button board cable (1) from the power button board.

Release the volume button board cable from the retention clips (2) built into the battery.

Remove the two Phillips PM1.5×2.0 screws (3) that secure the volume button board to the
bottom cover.

Tablet component replacement procedures

Remove the volume button board (4) and cable.

NOTE: In the process of removing the volume button board, the volume button actuator may be
accidentally dislodged from the bottom cover. To replace the volume button actuator, refer to the
following illustration.
The volume button actuator is included in the Button Kit, spare part number 747634-001.

Reverse this procedure to install the volume button board.

Chapter 5 Removal and replacement procedures

Audio jack board
Description

Spare part number

Audio jack board (includes audio jack and cable)

747627-001

Before removing the audio jack board, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet.

Disconnect all external devices from the tablet.

Remove the display assembly (see Display assembly on page 30).

Remove the NFC antenna (see NFC antenna on page 38).

Remove the audio jack board:
1.

Disconnect the audio jack board cable (1) from the system board.

Remove the two Phillips PM1.3×2.0 screws (2) that secure the audio jack board to the
bottom cover.

Remove the audio jack board (3) and cable.

Reverse this procedure to install the audio jack board.

Tablet component replacement procedures

Vibrator module
Description

Spare part number

Vibrator module (includes cable, double-sided adhesive, plastic cover)

747630-001

Before removing the vibrator module, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet.

Disconnect all external devices from the tablet.

Remove the display assembly (see Display assembly on page 30).

Remove the NFC antenna (see NFC antenna on page 38).

Remove the vibrator module:
1.

Disconnect the vibrator module cable (1) from the system board.

Chapter 5 Removal and replacement procedures

Detach the vibrator module (2) from the bottom cover. (The vibrator module is attached to the
bottom cover with double-sided adhesive.)

Remove the vibrator module and cable.
NOTE: The vibrator module cover is attached to the vibrator module with double-sided adhesive.

Reverse this procedure to install the vibrator module.

Battery
Description

Spare part number

2-cell, 30-Wh, 4.0-Ah, Li-ion battery (includes battery cable and WWAN/GPS main transceiver
and antenna cable)

728558-005

Before removing the battery, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet.

Disconnect all external devices from the tablet.

Remove the display assembly (see Display assembly on page 30).

Tablet component replacement procedures

Remove the NFC antenna (see NFC antenna on page 38).

Remove the power button board (see Power button board on page 45).

Remove the battery:
1.

Release the volume button board cable from the retention clips (1) built into the battery.

Release the tab (2) built into the bottom cover that secures the WWAN/GPS antenna cables, and
then release the antenna cables (3).

Detach the WWAN/GPS main transceiver (4) from the bottom cover. (The WWAN/GPS main
transceiver is attached to the bottom cover with double-sided adhesive.)

Remove the six Phillips PM1.3×2.0 screws (5) that secure the battery to the bottom cover.

Remove the battery (6).

Reverse this procedure to install the battery.

Chapter 5 Removal and replacement procedures

System board
NOTE: The system board spare part kit is equipped with an Intel Atom z3795 quad core 1.60-GHz
processor (burst up to 2.39-GHz; 2.0-MB L2 cache), and 4096-MB of system memory and includes the
processor, memory, and eMMC.
Description

Spare part number

Equipped with 128-GB of eMMC primary storage

753741-001

Equipped with 64-GB of eMMC primary storage

753740-001

Before removing the system board, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet.

Disconnect all external devices from the tablet.

Remove the display assembly (see Display assembly on page 30), and then remove the
following components:
a.

NFC antenna (see NFC antenna on page 38)

WWAN module (see WWAN module on page 39)

Power button board (see Power button board on page 45)

Battery (see Battery on page 51)

Remove the system board:
1.

Release the forward-facing webcam (1) from the molding built into the bottom cover.

Disconnect the audio jack board cable (2) from the system board.

Tablet component replacement procedures

Release the ZIF connector (3) to which the WLAN ribbon cable is attached, and then disconnect
the WLAN ribbon cable from the WLAN module.

Chapter 5 Removal and replacement procedures

Remove the five Phillips PM1.3×2.0 screws that secure the battery to the bottom cover.

Lift the top edge of the system board (1) and swing it up and forward until it rests upside down
above the tablet.

Remove the two Phillips PM1.3×1.5 broad head screws (2) that secure the docking connector
cable to the system board.

Tablet component replacement procedures

Disconnect the docking connector cable (3) from the system board.

Remove the system board.

NOTE: In the process of removing the system board, the autorotate switch actuator may be
accidentally dislodged from the bottom cover. To replace the autorotate switch actuator, refer to the
following illustration. When installing the autorotate switch actuator, make sure the two tabs (1) on the
autorotate switch actuator engage the autorotate switch (2) on the system board.
The autorotate switch actuator is included in the Button Kit, spare part number 747634-001.

Chapter 5 Removal and replacement procedures

Reverse this procedure to install the system board.

Forward-facing webcam
NOTE: The forward-facing webcam is included in the Webcam/Microphone Kit, spare part number
762828-001.
Before removing the forward-facing webcam, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet.

Disconnect all external devices from the tablet.

Remove the display assembly (see Display assembly on page 30), and then remove the
following components:
a.

NFC antenna (see NFC antenna on page 38)

WWAN module (see WWAN module on page 39)

Power button board (see Power button board on page 45)

Battery (see Battery on page 51)

System board (see System board on page 53)

Remove the forward-facing webcam:
1.

Turn the system board upside down, with the top toward you.

Tablet component replacement procedures

Release the ZIF connector (1) to which the forward-facing webcam cable is attached, and then
disconnect the forward-facing webcam cable (2) from the system board.

Remove the forward-facing webcam and cable.

Reverse this procedure to install the forward-facing webcam.

Slot cover
NOTE: The slot cover is included in the Button Kit, spare part number 747634-001.
Before removing the slot cover, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet.

Disconnect all external devices from the tablet.

Remove the display assembly (see Display assembly on page 30), and then remove the
following components:
a.

NFC antenna (see NFC antenna on page 38)

WWAN module (see WWAN module on page 39)

Power button board (see Power button board on page 45)

Battery (see Battery on page 51)

System board (see System board on page 53)

Remove the slot cover:

Remove the four Phillips PM1.3×2.0 screws (1) that secure the slot cover retention bracket and
spring bracket to the bottom cover.

Remove the slot cover retention bracket (2) and the slot cover spring bracket (3).

Chapter 5 Removal and replacement procedures

Remove the slot cover (4) by pressing it through the bottom cover.

Remove the slot cover.

Reverse this procedure to install the slot cover.

Docking connector cable
Description

Spare part number

Docking connector cable (includes double-sided adhesive)

747631-001

Before removing the docking connector cable, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet.

Disconnect all external devices from the tablet.

Remove the display assembly (see Display assembly on page 30), and then remove the
following components:
a.

NFC antenna (see NFC antenna on page 38)

WWAN module (see WWAN module on page 39)

Power button board (see Power button board on page 45)

Tablet component replacement procedures

Battery (see Battery on page 51)

System board (see System board on page 53)

Remove the docking connector cable:
1.

Disconnect the vibrator module cable (1) from the docking connector cable.

Disconnect the speaker cable (2) from the docking connector cable.

Remove the two Phillips PM1.3×2.0 screws (3) that secure the docking connector cable bracket to
the bottom cover.

Remove the docking connector bracket (4).
The docking connector bracket is included in the Button Kit, spare part number 747634-001.

Detach the docking connector cable (1) from the surface of the bottom cover. (The docking
connector cable is attached to the bottom cover with double-sided adhesive.)

Release the docking connector (2) from the bottom cover by sliding it away from the opening in
the bottom edge.

Chapter 5 Removal and replacement procedures

Remove the docking connector cable (3).

Reverse this procedure to install the docking connector cable.

WLAN antenna
NOTE: The WLAN antenna are included in the Antenna Kits and include the WLAN antenna main
and auxiliary cables and transceivers.
Description

Spare part number

Antenna Kit for use only in European countries and regions

767884-001

Antenna Kit for use only in Japan

767885-001

Antenna Kit for use only in the United States

767883-001

Before removing the WLAN antenna, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet.

Disconnect all external devices from the tablet.

Remove the display assembly (see Display assembly on page 30), and then remove the
following components:
a.

NFC antenna (see NFC antenna on page 38)

WWAN module (see WWAN module on page 39)

Power button board (see Power button board on page 45)

Tablet component replacement procedures

Battery (see Battery on page 51)

System board (see System board on page 53)

Remove the WLAN antenna:
1.

Release the WLAN antenna cables from the routing channel (1) built into the bottom cover.

Detach the WLAN antenna transceivers (2) from the bottom cover.

Release the tabs (3) built into the bottom cover that secure the speaker cable, and then release the
WLAN antenna cables.

Remove the WLAN antenna cables and transceivers (4).

Reverse this procedure to install the WLAN antenna.

Chapter 5 Removal and replacement procedures

WWAN/GPS auxiliary antenna
NOTE: The WWAN/GPS auxiliary antenna are included in the Antenna Kits and include the
WWAN/GPS auxiliary antenna cable and transceiver.
Description

Spare part number

Antenna Kit for use only in European countries and regions

767884-001

Antenna Kit for use only in Japan

767885-001

Antenna Kit for use only in the United States

767883-001

Before removing the WWAN/GPS auxiliary antenna, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet.

Disconnect all external devices from the tablet.

Remove the display assembly (see Display assembly on page 30), and then remove the
following components:
a.

NFC antenna (see NFC antenna on page 38)

WWAN module (see WWAN module on page 39)

Power button board (see Power button board on page 45)

Battery (see Battery on page 51)

System board (see System board on page 53)

Remove the WWAN/GPS auxiliary antenna:
1.

Detach the WWAN/GPS auxiliary antenna transceiver (1) from the bottom cover.

Tablet component replacement procedures

Remove the WWAN/GPS auxiliary antenna cable and transceiver (2).

Reverse this procedure to install the WWAN/GPS auxiliary antenna.

Chapter 5 Removal and replacement procedures

Speakers
Description

Spare part number

Speakers (include left and right speakers and cables)

747629-001

Before removing the speakers, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet.

Disconnect all external devices from the tablet.

Remove the display assembly (see Display assembly on page 30), and then remove the
following components:
a.

NFC antenna (see NFC antenna on page 38)

WWAN module (see WWAN module on page 39)

Power button board (see Power button board on page 45)

Battery (see Battery on page 51)

System board (see System board on page 53)

Docking connector cable (see Docking connector cable on page 59)

Remove the speakers:
1.

Release the tabs (1) built into the bottom cover that secure the speaker cable, and then release the
speaker cable.

Remove the four Phillips PM1.3×2.0 screws (2) that secure the speakers to the bottom cover.

Tablet component replacement procedures

Remove the speakers (3).

Reverse this procedure to install the speakers.

Chapter 5 Removal and replacement procedures

Retail Jacket component replacement procedures
There are as many as 31 screws that must be removed, replaced, and/or loosened when servicing the
Retail Jacket. Make special note of each screw size and location during removal and replacement.

Top cap
Description

Spare part number

Top cap (includes 4 captive screws, secured by C-rings)

744025-001

Before disassembling the Retail Jacket, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet or the
Retail Jacket.

Disconnect all external devices from the Retail Jacket.

Remove the top cap:
1.

Place the Retail Jacket face down on the work surface with the top cap toward you.

Loosen the 4 captive screws (1) that secure the top cap to the Retail Jacket.

Remove the top cap (2) from the Retail Jacket.

CAUTION: Before positioning the Retail Jacket with the tablet display panel facing down, make
sure the work surface is clear of tools, screws, and any other foreign objects. Failure to follow this
caution can result in damage to the display panel.
4.

Turn the Retail Jacket right side up with the bottom toward you.

Retail Jacket component replacement procedures

If installed, slide the tablet out of the Retail Jacket.

Reverse this procedure to install the top cap.

Battery
Description

Spare part number

Battery (2-cell, 21-Wh, 2.96-Ah, Li-ion)

687946-001

Before removing the battery, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet or the
Retail Jacket.

Disconnect all external devices from the Retail Jacket.

If installed, remove the tablet from the Retail Jacket (see Top cap on page 67).

Remove the battery:
1.

Loosen the 4 captive screws (1) that secure the battery to the Retail Jacket.

Chapter 5 Removal and replacement procedures

Remove the battery (2) from the Retail Jacket.

Reverse this procedure to install the battery.

Front cover
Description

Spare part number

Front cover (includes bar code scanner lens and adhesive liner)

744030-001

Before removing the front cover, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet or the
Retail Jacket.

Disconnect all external devices from the Retail Jacket.

Remove the top cap (see Top cap on page 67).

If installed, remove the tablet from the Retail Jacket (see Top cap on page 67).

NOTE: When replacing the front cover, be sure the following components are removed from the
defective front cover and installed on the replacement front cover:
●

Bar code scanner module (see Bar code scanner module and Cable connector board
on page 73)

●

Card connector board (see Bar code scanner module and Cable connector board on page 73)

●

Battery connector board (see Battery connector board on page 75)

●

System board (see System board on page 76)

Retail Jacket component replacement procedures

Remove the front cover:

Position the Retail Jacket with the top toward you.

Remove the adhesive-backed liner that covers the front cover.

Release the ZIF connector (1) to which the left-side credit card reader board cable is attached,
and then disconnect the left-side credit card reader board cable (2) from the left-side credit card
reader board.

Chapter 5 Removal and replacement procedures

Close the ZIF connector (3).
CAUTION: Failure to close the ZIF connector as instructed in step 4 can lead to damage to
Retail Jacket components.

Position the Retail Jacket with the bottom toward you.

Retail Jacket component replacement procedures

Remove the two Phillips PM1.3×3.0 screws that secure the front cover to the Retail Jacket.

Position the Retail Jacket with the top toward you.

Remove the four Phillips PM1.9×3.0 screws that secure the front cover to the Retail Jacket.

Chapter 5 Removal and replacement procedures

Remove the front cover by sliding it away from the Retail Jacket.

Reverse this procedure to install the front cover.

Bar code scanner module and Cable connector board
NOTE: The bar code scanner module and cable connector board spare part kits do not include the
respective cables. The cables are included in the Cable Kit, spare part number 744031-001.
Description

Spare part number

Bar code scanner module

744037-001

Cable connector board

744034-001

Before removing the bar code scanner module and cable connector board, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet or the
Retail Jacket.

Disconnect all external devices from the Retail Jacket.

Remove the top cap (see Top cap on page 67).

If installed, remove the tablet from the Retail Jacket (see Top cap on page 67).

Remove the front cover (see Front cover on page 69).

Remove the bar code scanner module and cable connector board:
1.

Turn the front cover upside down with the top toward you.

Release the ZIF connector (1) to which the cable connector board cable is attached, and then
disconnect the cable connector board cable from the system board.

Retail Jacket component replacement procedures

Detach the cable connector board cable (2) from the front cover. (The cable connector board
cable is attached to the front cover with double-sided adhesive.)

Remove the two Phillips PM1.3×3.0 screws (3) that secure the bar code scanner module to the
front cover.

Remove the two Phillips PM1.9×3.0 screws (4) that secure the cable connector board to the
front cover.

Remove the bar code scanner module (5) and the cable connector board and cable.

Turn the bar code scanner module and the cable connector board over so the ZIF connector on the
back of the cable connector board is accessible.

Chapter 5 Removal and replacement procedures

Release the ZIF connector (1) to which the bar code scanner module cable is attached, and then
disconnect the bar code scanner module cable (2) from the cable connector board.

Reverse this procedure to install the bar code scanner module and cable connector board.

Battery connector board
Description

Spare part number

Battery connector board (includes cable)

744033-001

Before removing the battery connector board, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet or the
Retail Jacket.

Disconnect all external devices from the Retail Jacket.

Remove the top cap (see Top cap on page 67).

If installed, remove the tablet from the Retail Jacket (see Top cap on page 67).

Remove the front cover (see Front cover on page 69).

Remove the battery connector board:
1.

Turn the front cover upside down with the top toward you.

Disconnect the battery connector board cable (1) from the system board.

Remove the two Phillips PM1.9×3.0 screws (2) that secure the battery connector board to the
front cover.

Retail Jacket component replacement procedures

Lift the bottom edge of the battery connector board (3) until the board rests at an angle, and then
slide the board out of the opening in the front cover.

Remove the battery connector board and cable.

Reverse this procedure to install the battery connector board.

System board
Description

Spare part number

System board (includes docking connector and USB port)

744032-001

Before removing the system board, follow these steps:

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet or the
Retail Jacket.

Disconnect all external devices from the Retail Jacket.

Remove the top cap (see Top cap on page 67).

If installed, remove the tablet from the Retail Jacket (see Top cap on page 67).

Remove the front cover (see Front cover on page 69).

Chapter 5 Removal and replacement procedures

Remove the system board:
1.

Turn the front cover upside down with the top toward you.

Disconnect the battery connector board cable (1) from the system board.

Release the ZIF connector (2) to which the cable connector board cable is attached, and then
disconnect the cable connector board cable from the system board.

Release the ZIF connector (3) to which the credit card reader/left board cable is attached, and
then disconnect the credit card reader/left board cable from the system board.

Remove the five Phillips PM1.9×3.0 screws (4) that secure the system board to the front cover.

Remove the two Phillips PM1.9×3.0 screws (5) that secure the system board to the front cover.

Slide the docking connector (6) out of the opening in the front cover, and then remove the
system board.

Reverse this procedure to install the system board.

Retail Jacket component replacement procedures

Credit card reader board
NOTE: The credit card reader board spare part kits do not include the respective cables. The cables
are included in the Cable Kit, spare part number 744031-001.
Description

Spare part number

Left-side credit card reader board

744027-001

Right-side credit card reader board

744028-001

Before removing the credit card reader boards, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet or the
Retail Jacket.

Disconnect all external devices from the Retail Jacket.

Remove the top cap (see Top cap on page 67).

If installed, remove the tablet from the Retail Jacket (see Top cap on page 67).

Remove the front cover (see Front cover on page 69).

Remove the credit card reader boards:

Remove the Phillips PM1.9×3.0 screw (1) that secures the left-side credit card reader board to the
rear cover.

Turn the left-side credit card reader board (2) over so the ZIF connector on the back of the board
is accessible.

Chapter 5 Removal and replacement procedures

Release the ZIF connector (3) to which the right-side credit card reader board cable is attached,
and then disconnect the right-side credit card reader board cable (4) from the left-side credit card
reader board.

Remove the left-side credit card reader board.

Detach the right-side credit card reader board cable (1) from the rear cover. (The right-side credit
card reader board cable is attached to the rear cover with double-sided adhesive.)

Remove the Phillips PM1.9×3.0 screw (2) that secures the right-side credit card reader board to
the rear cover.

Retail Jacket component replacement procedures

Remove the right-side credit card reader board (3) and cable.

Reverse this procedure to install the credit card reader boards.

Credit card reader
Description

Spare part number

Credit card reader

744026-001

Before removing the credit card reader, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet or the
Retail Jacket.

Disconnect all external devices from the Retail Jacket.

Remove the top cap (see Top cap on page 67).

If installed, remove the tablet from the Retail Jacket (see Top cap on page 67).

Remove the front cover (see Front cover on page 69).

Remove the credit card reader:

Disconnect the credit card reader cable (1) from the right-side credit card reader board.

Release the credit card reader cable (2) from the routing channel built into the rear cover.

Remove the two Phillips PM1.9×3.0 screws (3) that secure the retention tabs and the credit card
reader to the rear cover.

Remove the two retention tabs (4).

Chapter 5 Removal and replacement procedures

Remove the credit card reader (5).

Reverse this procedure to install the credit card reader.

Retail Jacket component replacement procedures

Security Jacket component replacement procedures
There are as many as 13 screws that must be removed, replaced, and/or loosened when servicing the
Security Jacket. Make special note of each screw size and location during removal and replacement.

Card reader cover and Top cap
Description

Spare part number

Card reader cover

744039-001

Top cap (includes rubber trim)

744047-001

Before disassembling the Security Jacket, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet or the
Security Jacket.

Disconnect all external devices from the Security Jacket.

Remove the card reader cover and top cap:

Place the Security Jacket face down on the work surface with the top cap toward you.

Release the card reader cover (1) by sliding it toward the top of the Security Jacket.

Remove the card reader cover (2) by lifting it away from the Security Jacket.

Remove the Phillips PM1.9×3.0 screw (1) that secures the top cap to the Security Jacket.

Slide the top cap release latch (2) to release the top cap from the Security Jacket.

Chapter 5 Removal and replacement procedures

Remove the top cap (3) from the Security Jacket.

CAUTION: Before positioning the Security Jacket with the tablet display panel facing down,
make sure the work surface is clear of tools, screws, and any other foreign objects. Failure to
follow this caution can result in damage to the display panel.
7.

Turn the Security Jacket right side up with the bottom toward you.

If installed, slide the tablet out of the Security Jacket.

Reverse this procedure to install the top cap.

Security Jacket component replacement procedures

Front cover
Description

Spare part number

Front cover

744048-001

Before removing the front cover, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet or the
Security Jacket.

Disconnect all external devices from the Security Jacket.

Remove the card reader cover and top cap (see Card reader cover and Top cap on page 82).

If installed, remove the tablet from the Security Jacket (see Card reader cover and Top cap
on page 82).

NOTE: When replacing the front cover, be sure the system board is removed from the defective top
cover and installed on the replacement front cover (see System board on page 76).
Remove the front cover:

Turn the Security Jacket upside down with the top toward you.

Remove the two Phillips PM1.5×3.4 screws that secure the front cover to the Security Jacket.

Turn the Security Jacket right side up with the bottom toward you.

Chapter 5 Removal and replacement procedures

Remove the two Phillips PM1.3×3.4 screws (1) that secure the front cover to the Security Jacket.

Release the front cover (2) by sliding it partially away from the Security Jacket.

Lift the bottom edge of the front cover (1) and swing it up and back until it rests upside down on
the Security Jacket.

Disconnect the fingerprint reader board cable (2) from the low insertion force (LIF) connector on
the system board.

Disconnect the card reader board cable (3) from the LIF connector on the system board.

Remove the front cover.

Reverse this procedure to install the front cover.

Security Jacket component replacement procedures

System board
Description

Spare part number

System board (includes docking connector, HDMI port, and USB port)

744044-001

Before removing the system board, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet or the
Security Jacket.

Disconnect all external devices from the Security Jacket.

Remove the card reader cover and top cap (see Card reader cover and Top cap on page 82).

If installed, remove the tablet from the Security Jacket (see Card reader cover and Top cap
on page 82).

Remove the front cover (see Front cover on page 84).

Remove the system board:
1.

Place the front cover face down on the work surface with the bottom toward you.

Remove the six Phillips PM1.9×3.4 screws (1) that secure the system board to the front cover.

Release the docking connector (2) from the opening in the front cover.

Remove the system board (3).

Reverse this procedure to install the system board.

Chapter 5 Removal and replacement procedures

Docking connector cable
NOTE: The docking connector cable is included in the Cables/Connectors Kit, spare part number
744045-001.
Before removing the docking connector cable, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet or the
Security Jacket.

Disconnect all external devices from the Security Jacket.

Remove the card reader cover and top cap (see Card reader cover and Top cap on page 82).

If installed, remove the tablet from the Security Jacket (see Card reader cover and Top cap
on page 82).

Remove the front cover (see Front cover on page 84).

Remove the system board (see System board on page 86).

Remove the docking connector cable:
1.

Turn the system board upside down with the top toward you.

Remove the two Phillips PM1.9×3.4 screws (1) that secure the docking connector cable to the
system board.

Remove the docking connector bracket (2).

Security Jacket component replacement procedures

Remove the docking connector cable (3).

Reverse this procedure to install the docking connector cable.

Card reader board
Description

Spare part number

Card reader board

744043-001

Before removing the card reader board, follow these steps:

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet or the
Security Jacket.

Disconnect all external devices from the Security Jacket.

Remove the card reader cover and top cap (see Card reader cover and Top cap on page 82).

If installed, remove the tablet from the Security Jacket (see Card reader cover and Top cap
on page 82).

Remove the front cover (see Front cover on page 84).

Chapter 5 Removal and replacement procedures

Remove the card reader board:
1.

Position the rear cover with the bottom toward you.

Detach the tape (1) that secures the card reader board to the rear cover.

Remove the card reader board (2) and cable.

Reverse this procedure to install the card reader board.

Fingerprint reader board
Description

Spare part number

Fingerprint reader board

744042-001

Before removing the fingerprint reader board, follow these steps:
1.

Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.

Disconnect the power from the tablet by unplugging the power cord from the tablet or the
Security Jacket.

Disconnect all external devices from the Security Jacket.

Remove the card reader cover and top cap (see Card reader cover and Top cap on page 82).

If installed, remove the tablet from the Security Jacket (see Card reader cover and Top cap
on page 82).

Remove the front cover (see Front cover on page 84).

Security Jacket component replacement procedures

Remove the fingerprint reader board:
1.

Position the rear cover with the bottom toward you.

Remove the spring (1) from the spring retention tabs (2).

Remove the fingerprint reader board (3) and cable.

Reverse this procedure to install the fingerprint reader board.

Chapter 5 Removal and replacement procedures

Computer Setup and HP PC
Hardware Diagnostics (UEFI)

Using Computer Setup
Computer Setup, or F10 BIOS Setup (Basic Input/Output System), controls communication between all
the input and output devices on the system (such as disk drives, display, keyboard, mouse, and printer).
Computer Setup includes settings for the types of devices installed, the startup sequence of the tablet,
and the amount of system and extended memory.
NOTE: Use extreme care when making changes in Computer Setup. Errors can prevent the tablet
from operating properly.

Starting Computer Setup
To start Computer Setup, follow these steps:
1.

Shut down the tablet.

To power on the tablet, press the Power button and Volume down button simultaneously. The
Startup menu is displayed.

Press f10 to enter Computer Setup.

Using Computer Setup

Navigating and selecting in Computer Setup
To navigate and select in Computer Setup, follow these steps:
1.

Shut down the tablet.

To power on the tablet, press the Power button and Volume down button simultaneously.
The Startup menu is displayed.

Press f10 to enter Computer Setup.
●

Tap a menu or a menu item to select it.

●

To close open dialog boxes and return to the main Computer Setup screen, tap Escape, and
then follow the on-screen instructions.

To exit Computer Setup menus without saving your changes, select Main, select Ignore
Changes and Exit, and then follow the on-screen instructions.

To save your changes and exit, select Main, select Save Changes and Exit, and then follow
the on-screen instructions.

Restoring factory settings in Computer Setup
NOTE: Restoring defaults will not change the hard drive mode.
To return all settings in Computer Setup to the values that were set at the factory, follow these steps:
1.

Shut down the tablet.

To power on the tablet, press the Power button and Volume down button simultaneously.
The Startup menu is displayed.

Press f10 to enter Computer Setup.

Select Main, and then tap Restore Defaults.

Follow the on-screen instructions.

To save your changes and exit, select Save Changes and Exit, and then follow the onscreen instructions.
Your changes go into effect when the computer restarts.

NOTE: Your password settings and security settings are not changed when you restore the
factory settings.

Chapter 6 Computer Setup and HP PC Hardware Diagnostics (UEFI)

Updating the BIOS
Updated versions of the BIOS may be available on the HP website.
Most BIOS updates on the HP website are packaged in compressed files called SoftPaqs.
Some download packages contain a file named Readme.txt, which contains information regarding
installing and troubleshooting the file.

Determining the BIOS version
To determine whether available BIOS updates contain later BIOS versions than those currently installed
on the tablet, you need to know the version of the system BIOS currently installed.
To display BIOS version information (also known as ROM date and System BIOS), see Using Computer
Setup on page 91.
1.

Shut down the tablet.

To power on the tablet, press the Power button and Volume down button simultaneously.
The Startup menu is displayed.

Press f10 to enter Computer Setup.

Select Main, and then select System Information.

Follow the on-screen instructions.

To exit Computer Setup menus without saving your changes, select Main, select Ignore
Changes and Exit, and then follow the on-screen instructions.

Downloading a BIOS Update
CAUTION: To reduce the risk of damage to the tablet or an unsuccessful installation, download and
install a BIOS update only when the tablet is connected to reliable external power using the AC
adapter. Do not download or install a BIOS update while the tablet is running on battery power,
docked in an optional docking device, or connected to an optional power source. During the
download and installation, follow these instructions:
Do not disconnect power on the tablet by unplugging the power cord from the AC outlet.
Do not shut down the tablet or initiate Sleep.
Do not insert, remove, connect, or disconnect any device, cable, or cord.
1.

To access HP Support Assistant on the Start screen, tap the HP Support Assistant app.

Tap Updates and tune-ups, and then tap Check for HP updates now.

Using Computer Setup

Follow the on-screen instructions.

At the download area, follow these steps:
a.

Identify the most recent BIOS update and compare it to the BIOS version currently installed on
your tablet. Make a note of the date, name, or other identifier. You may need this
information to locate the update later, after it has been downloaded to your hard drive.

Follow the on-screen instructions to download your selection to the hard drive.
If the update is more recent than your BIOS, make a note of the path to the location on your
hard drive where the BIOS update is downloaded. You will need to access this path when
you are ready to install the update.

NOTE: If you connect your tablet to a network, consult the network administrator before
installing any software updates, especially system BIOS updates.
BIOS installation procedures vary. Follow any instructions that are revealed on the screen after the
download is complete. If no instructions are revealed, follow these steps:
1.

Swipe from the right edge of the touch screen, tap Search, and then tap the search box. Type
file, and then tap File Explorer.

Select your hard drive designation. The hard drive designation is typically Local Disk (C:).

Using the hard drive path you recorded earlier, open the folder on your hard drive that contains
the update.

Double-tap the file that has an .exe extension (for example, filename.exe).
The BIOS installation begins.

Complete the installation by following the on-screen instructions.

NOTE: After a message on the screen reports a successful installation, you can delete the
downloaded file from your hard drive.

Using HP PC Hardware Diagnostics (UEFI)
HP PC Hardware Diagnostics is a Unified Extensible Firmware Interface (UEFI) that allows you to run
diagnostic tests to determine if the computer hardware is functioning properly. The tool runs outside of
the operating system to isolate hardware failures from issues that may be caused by the operating
system or other software components.
To start HP PC Hardware Diagnostics UEFI:
1.

Shut down the tablet if it is not already powered off.

To power on the tablet, press the Power button and Volume down button simultaneously.

Select System Diagnostics.

Select the type of diagnostic test that you want to run, and then follow the on-screen instructions.

NOTE: If you need to stop a diagnostic test while it is running, press anywhere on the screen.

Chapter 6 Computer Setup and HP PC Hardware Diagnostics (UEFI)

Specifications

Tablet specifications
Metric

U.S.

Width

17.80 cm

7.0 in

Depth

26.10 cm

10.28 in

Height

0.92 cm

0.36 in

Weight

0.68 kg

1.50 lbs

Dimensions

Input power
Operating voltage and current

9 V DC @ 1.1A – 10W

Temperature
Operating

5°C to 35°C

41°F to 95°F

Nonoperating

-20°C to 60°C

-4°F to 140°F

Relative humidity (noncondensing)
Operating

10% to 90%

Nonoperating

5% to 95%

Maximum altitude (unpressurized)
Operating

-15 m to 3,048 m

-50 ft to 10,000 ft

Nonoperating

-15 m to 12,192 m

-50 ft to 40,000 ft

NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The device operates well within this
range of temperatures.

Tablet specifications

Backup and recovery

To protect your information, use Windows backup and restore utilities to back up individual files and
folders, back up your entire hard drive, create system repair media (select models only) by using an
optional external flash drive, or an optional external optical drive, or create system restore points. In
case of system failure, you can use the backup files to restore the contents of your tablet.
1.

Swipe from the right edge of the touch screen to display the charms, tap Search, and then tap
the search box.

In the search box, type restore, and then select from the list of displayed options.

NOTE: For detailed instructions on various backup and restore options, perform a search for these
topics in Windows Help and Support.
In case of system instability, HP recommends that you print the recovery procedures and save them for
later use.
NOTE: Windows includes the User Account Control feature to improve the security of your tablet. You
may be prompted for your permission or password for tasks such as installing software, running utilities,
or changing Windows settings. For more information, see Windows Help and Support.

Backing up your information
Recovery after a system failure is as good as your most recent backup. You should create system repair
media and your initial backup immediately after initial system setup. As you add new software and
data files, you should continue to back up your system on a regular basis to maintain a reasonably
current backup.
For more information on the Windows backup features, see Windows Help and Support.

Chapter 8 Backup and recovery

Performing a system recovery
In case of system failure or instability, the computer provides the following tools to recover your files:
●

Windows recovery tools: You can use Windows Backup and Restore to recover information you
have previously backed up. You can also use Windows Automatic Repair to fix problems that
might prevent Windows from starting correctly.

●

f11 recovery tools: You can use the f11 recovery tools to recover your original hard drive image.
The image includes the Windows operating system and software programs installed at the factory.

NOTE: If you are unable to boot (start up) your tablet and you cannot use the system repair media
you previously created (select models only), contact support.

Using the Windows recovery tools
To recover information you previously backed up, see Windows Help and Support for steps on
restoring files and folders.
To recover your information using Automatic Repair, follow these steps:
CAUTION: Some Startup Repair options will completely erase and reformat the hard drive. All files
you have created and any software installed on the computer are permanently removed. When
reformatting is complete, the recovery process restores the operating system, as well as the drivers,
software, and utilities from the backup used for recovery.
NOTE: An external keyboard, mouse, and external flash drive may be required to perform
this procedure.
1.

If possible, back up all personal files.

If possible, check for the presence of the Recovery Image partition and the Windows partition.
Swipe from the right edge of the touch screen, tap Search, and then tap the search box. Type
file, and then tap File Explorer.

If the Windows partition and the Recovery Image partition are listed, shut down the tablet.

To power on the tablet, press the Power button and Volume down button simultaneously.
The Startup menu is displayed.

Select Troubleshoot, select Advanced Options, and then select Startup Repair.

Follow the on-screen instructions.

NOTE: For additional information on recovering information using the Windows tools, perform a
search for these topics in Windows Help and Support.

Performing a system recovery

Using f11 recovery tools
CAUTION: Using f11 completely erases hard drive contents and reformats the hard drive. All files
that you have created and any software that you have installed on the tablet are permanently removed.
The f11 recovery tool reinstalls the operating system, drivers, Windows updates, and language packs
that were installed at the factory. All other software applications must be downloaded from HP.com or
the Windows Store.
NOTE: An external keyboard, mouse, and external flash drive may be required to perform
this procedure.
To recover the original hard drive image using f11:
1.

If possible, back up all personal files.

If possible, check for the presence of the HP Recovery partition: Swipe from the right edge of the
touch screen, tap Search, and then tap the search box. Type pc, and then tap This PC.

If the HP Recovery partition is listed, shut down the tablet.

To power on the tablet, press the Power button and Volume down button simultaneously.
The Startup menu is displayed.

Tap F11 HP Recovery, and then follow the on-screen instructions.

Changing the boot device order
To change the boot order so that you can boot from an external device:
NOTE: An external flash drive is required to perform this procedure.
1.

If possible, back up all personal files.

Shut down the tablet.

Connect the external flash drive.

To power on the tablet, press the Power button and Volume down button simultaneously.
The Startup menu is displayed.

Tap F9 Boot Options.

Select the external flash drive as the boot device.

Restart the tablet.

Chapter 8 Backup and recovery

Using Windows Refresh or Windows Reset
When your tablet is not working properly and you need to regain system stability, the Windows
Refresh option allows you to start fresh and keep what is important to you.
The Windows Reset option allows you to perform detailed reformatting of your tablet, or remove
personal information before you give away or recycle your tablet. For more information on these
features, see Windows Help and Support.

Performing a system recovery

Statement of Volatility

The purpose of this document is to provide general information regarding non-volatile memory in
industry-standards based HP Business Notebook PC systems and provide general instructions for
restoring nonvolatile memory that can contain personal data after the system has been powered off and
the hard drive has been removed.
HP Business Notebook PC products that use Intel-based or AMD®-based system boards contain volatile
DDR memory. The amount of nonvolatile memory present in the system depends upon the system
configuration. Intel-based and AMD-based system boards contain nonvolatile memory subcomponents
as originally shipped from HP assuming that no subsequent modifications have been made to the
system and assuming that no applications, features, or functionality have been added to or installed on
the system.
Following system shutdown and removal of all power sources from an HP Business Notebook PC
system, personal data can remain on volatile system memory (DIMMs) for a finite period of time and
will also remain in nonvolatile memory. The steps below will remove personal data from the notebook
PC, including the nonvolatile memory found in Intel-based and AMD-based system boards. Some of
these steps are disclosed in the Maintenance and Service Guides available for HP PC products
available on the product support pages at www.hp.com.
1.

100

Follow steps (a) through (I) below to restore the nonvolatile memory that can contain personal
data. Restoring or re-programming nonvolatile memory that does not store personal data is neither
necessary nor recommended.
a.

Enter BIOS (F10) Setup by powering on the system and pressing F10 when prompted near
the bottom of the display, or press the ESC key to display the start up menu, then press F10 .
If the system has a BIOS administrator password, enter the password at the prompt.

Select the File menu, then Restore Defaults.

Select the System Configuration menu, then Restore Security Defaults.

If an asset or ownership tag is set, select the Security menu and scroll down to the Utilities
menu. Select System IDs, and then select the tag that has been set. Press the spacebar
once to clear the tag, then press Enter to return to the prior menu.

If a DriveLock password is set, select the Security menu, scroll down to DriveLock, then
select DriveLock password. Select the desired hard drive. Click Disable protection,
enter the existing master DriveLock password, then press Enter to confirm and return to the
prior menu. Repeat this procedure if more than one hard drive has a DriveLock password.

Chapter 9 Statement of Volatility

If an Automatic DriveLock password is set, select the Security menu, scroll down to
Automatic DriveLock, then select the desired hard drive and disable protection. Repeat
this procedure if more than one hard drive has an Automatic DriveLock password.

Select the File menu, then Reset BIOS Security to factory default. Click yes at the
warning message.

Select the File menu, then Save Changes and Exit.

Reboot the system. If the system has a Trusted Platform Module and/or fingerprint sensor, one
or two prompts will appear: one to clear the TPM and the other to reset fingerprint sensor.
Press F1 to accept or F2 to reject.
If the HP notebook model number ends in a ‘p’ or ‘w’ and includes Intel Centrino with
VProTM, reboot the PC and enter BIOS Setup by pressing F10 when prompted. Select
System Configuration, then AMT Options. Then select Un-configure AMT on next
boot. Select Save, then Yes. Select the File menu, and then select Save Changes and
Exit. Reboot the system and confirm that you want to un-configure AMT.

If the optional Intel Anti-Theft Technology (AT) was activated, contact the provider to
deactivate it.

If the optional Absolute® Software Computrace® management and tracking service was
activated on the notebook PC, contact the provider to deactivate it.

Remove all power and system batteries for at least 24 hours.

Remove and retain the storage drive or clear the contents of the drive.
a.

Hard Disk Drive (HDD)
Clear the HDD contents by using the HP Disk Sanitizer® utility or a third party application
that, ideally, is U.S. Department of Defense (DOD) 5220.22-M approved.
To run HP Disk Sanitizer, enter BIOS Setup by powering on the system and pressing F10
when prompted near the bottom of the display, or press ESC to display the start up menu,
then press F10. Select the Security menu and scroll down to the Utilities menu. Select
Disk Sanitizer and select the desired drive. For a higher level of protection, select
Optimum.
NOTE: This process will take a long time, and the amount of time varies based on the hard
drive capacity.

Solid State Drive (SSD)
Clear the SSD contents by using the BIOS Setup Secure Erase command option, or by using a
third party utility designed to erase data from an SSD. To run Secure Erase, enter BIOS Setup
by powering on the system and pressing F10 when prompted near the bottom of the display.
Select the Security menu and scroll down to the Utilities menu. Select Secure Erase and
select the desired hard drive.

101

Non-volatile memory usage

102

Non Volatile
Memory
Type

Amount
(Size)

Does this
memory
store
customer
data?

Does this
memory
retain data
when power
is removed?

What is the
purpose of
this
memory?

How is data
input into
this
memory?

How is this
memory
write
protected?

Real Time Clock
(RTC) battery
backed-up
CMOS
configuration
memory
(CMOS)

256 Bytes

Yes

Stores system
date and time
and limited
keyboard
controller data.

Using the F10
Setup utility or
changing the
Microsoft
Windows date
and time.

This memory is
not writeprotected. HP
recommends
password
protecting the
F10 Setup
utility.

Controller (NIC)
EEPROM

64 KBytes (not
customer
accessible)

Yes

Store NIC
configuration
and NIC
firmware.

Using a utility
from the NIC
vendor that can
be run from
DOS.

A utility is
required to
write data to
this memory
and is available
from NIC
vendor. Writing
data to this
ROM in an
inappropriate
manner will
render the NIC
nonfunctional.

Keyboard ROM

64 KBytes (not
customer
accessible)

Yes

Stores firmware
code
(keyboard,
mouse, &
battery
management).

Programmed at
the factory.
Code is
updated when
the system BIOS
is updated.

A utility is
required for
writing data to
this memory
and is available
on the HP
website.
Writing data to
this ROM in an
inappropriate
manner can
render the PC
nonfunctional.

DIMM Serial
Presence Detect
(SPD)
configuration
data

256 Bytes per
memory
module, 128
Bytes
programmable
(not customer
accessible)

Yes

Stores memory
module
information.

Programmed by
the memory
vendor.

Data cannot be
written to this
memory when
the module is
installed in a
PC. The specific
write protection
method varies
by memory
vendor.

Chapter 9 Statement of Volatility

Non Volatile
Memory
Type

Amount
(Size)

Does this
memory
store
customer
data?

Does this
memory
retain data
when power
is removed?

What is the
purpose of
this
memory?

How is data
input into
this
memory?

How is this
memory
write
protected?

System BIOS

4 to 5 MBytes

Yes

Store system
BIOS code and
PC
configuration
data.

System BIOS
code is
programmed at
the factory.
Code is
updated when
the system BIOS
is updated.
Configuration
data and
settings are
input using the
F10 setup utility
or a custom
utility.

A utility is
required for
writing data to
this memory
and is available
on the HP
website.
Writing data to
this ROM in an
inappropriate
manner can
render the PC
nonfunctional.

Intel
Management
Engine
Firmware
(present only in
models ending
in a ‘p’ or ‘w’
or with Intel
Centrino Pro
technology)

1.5 or 5
MBytes

Yes

Stores
Management
Engine Code,
Settings,
Provisioning
Data and iAMT
third party data
store.

Management
Engine Code is
programmed at
the factory.
Code is
updated via
Intel secure
firmware
update utility.
Unique
Provisioning
Data can be
entered at the
factory or by an
administrator
using the
Management
Engine (MEBx)
setup utility. The
third party data
store contents
can populated
by a remote
management
console or local
applications
registered by
an
administrator to
have access to
the space.

The Intel chipset
is configured to
enforce
hardware
protection to
block all direct
read/write
access to this
area. An Intel
utility is
required for
updating the
firmware. Only
firmware
updates
digitally signed
by Intel can be
applied using
this utility.

Non-volatile memory usage

103

104

Non Volatile
Memory
Type

Amount
(Size)

Does this
memory
store
customer
data?

Does this
memory
retain data
when power
is removed?

What is the
purpose of
this
memory?

How is data
input into
this
memory?

How is this
memory
write
protected?

Bluetooth flash

2 MBits

Yes

Stores Bluetooth
configuration
and firmware.

Programmed at
the factory.
Tools for writing
data to this
memory are not
publicly
available but
can be
obtained from
the silicon
vendor.

A utility is
required for
writing data to
this memory
and is made
available
through newer
versions of the
driver if the
flash requires
an upgrade.

802.11 WLAN
EEPROM

4 KBytes to 8
KBytes

Yes

Stores
configuration
and calibration
data.

Programmed at
the factory.
Tools for writing
data to this
memory are not
made public.

A utility is
required for
writing data to
this memory
and is typically
not made
available to the
public unless a
firmware
upgrade is
necessary to
address a
unique issue.

Webcam

64 KBits

Yes

Store webcam
configuration
and firmware.

Using a utility
from the device
manufacturer
that can be run
from Windows.

A utility is
required for
writing data to
this memory
and is typically
not made
available to the
public unless a
firmware
upgrade is
necessary to
address a
unique issue.

Fingerprint
reader

512 KBytes
flash

Yes

Stores
fingerprint
templates.

By enrolling in
HP ProtectTools
Security
Manager.

Only a digitally
signed
application can
make the call to
write to the
flash.

Chapter 9 Statement of Volatility

Questions and answers
1.

How can the BIOS settings be restored (returned to default settings)?
a.

Turn on or restart the computer and press F10 when prompted near the bottom of the display.

Select File, then select Restore defaults.

Follow the on-screen instructions.

Select File, save changes and exit, then press Enter.

What kind of configuration data is stored on the DIMM Serial Presence Detect
(SPD) memory module? How would this data be written?
The DIMM SPD memory contains information about the memory module such as size, serial
number, data width, speed/timing, voltage and thermal information. This information is written by
the module manufacturer and stored on an EEPROM. This EEPROM cannot be written to when the
memory module is installed in a PC. Third party tools do exist that can write to the EEPROM when
the memory module is not installed in a PC. There are various third party tools available to read
SPD memory.

Does the “Firmware Hub for System BIOS” contain the BIOS program? Is this chip
writable, and if so how?
The Firmware Hub does contain the BIOS program and is writable. A utility is required to perform
the write function.

In some PC systems, the Firmware Hub for System BIOS is a flash memory chip
so that updates can be written by the customer. Is this true for these BIOS chips?
Yes, they are flash memory chips.

What is meant by “Restore the nonvolatile memory found in Intel-based
system boards?”
This relates to clearing the Real Time Clock (RTC) CMOS memory that contains PC
configuration data.

Does resetting the CMOS configuration memory return the PC back to
factory defaults?
The process of resetting the CMOS will return certain system settings to factory default but will not
reset many of the system data and configuration defaults to their default settings. To return these
system data and configuration defaults to default settings, refer to question and answer 1 and
follow the instructions for returning the BIOS settings to factory defaults.

Questions and answers

105

10 Power cord set requirements

The wide-range input feature of the computer permits it to operate from any line voltage from 100 to
120 volts AC, or from 220 to 240 volts AC.
The 3-conductor power cord set included with the computer meets the requirements for use in the
country or region where the equipment is purchased.
Power cord sets for use in other countries and regions must meet the requirements of the country or
region where the computer is used.

Requirements for all countries
The following requirements are applicable to all countries and regions:

106

●

The length of the power cord set must be at least 1.0 m (3.3 ft) and no more than 2.0 m (6.5 ft).

●

All power cord sets must be approved by an acceptable accredited agency responsible for
evaluation in the country or region where the power cord set will be used.

●

The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage
rating of 125 or 250 V AC, as required by the power system of each country or region.

●

The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320
Standard Sheet C13 connector for mating with the appliance inlet on the back of the computer.

Chapter 10 Power cord set requirements

Requirements for specific countries and regions
Country/region

Accredited agency

Applicable note number

Australia

EANSW

Austria

OVE

Belgium

CEBC

Canada

CSA

Denmark

DEMKO

Finland

FIMKO

France

UTE

Germany

VDE

Italy

IMQ

Japan

METI

The Netherlands

KEMA

Norway

NEMKO

The People's Republic of China

COC

South Korea

Sweden

SEMKO

Switzerland

SEV

Taiwan

BSMI

The United Kingdom

BSI

The United States

The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.

The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole
grounding type with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.

The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the
Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm² conductor size. The wall plug
must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.

The flexible cord must be Type RVV, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.

The flexible cord must be Type VCTF, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.

Requirements for specific countries and regions

107

11 Recycling

When a non-rechargeable or rechargeable battery has reached the end of its useful life, do not dispose
of the battery in general household waste. Follow the local laws and regulations in your area for
battery disposal.
HP encourages customers to recycle used electronic hardware, HP original print cartridges, and
rechargeable batteries. For more information about recycling programs, see the HP Web site at
http://www.hp.com/recycle.

108

Chapter 11 Recycling

Index

Symbols/Numerics
3G antenna, spare part number
25
A
AC adapter cable, spare part
number 15, 21
AC adapter, spare part numbers
16, 19, 21
adapter cables
illustrated 15
spare part numbers 15
adhesive cover
spare part number 12
ambient light sensor 5
antenna
location 4
removal 61, 63
spare part numbers 10, 25,
61, 63
Antenna Kit, spare part numbers
10, 25, 61, 63
audio jack board
removal 49
spare part number 10, 23, 49
audio, product description 1
audio-in jack 6
audio-out jack 6
autorotate switch actuator
installation 56
spare part number 10, 56
B
bar code scanner module
removal 73
spare part number 12, 23, 73

battery
removal 51, 68
spare part numbers 10, 12,
21, 22, 51, 68
battery bay space saver, spare part
number 12, 22
battery connector board
removal 75
spare part number 13, 23, 75
bottom case, spare part number
11, 23
bottom components 7
Button Kit, spare part number 9,
24
buttons
power 7
volume down 6
volume up 6
Window 5
C
cable connector board
removal 73
spare part number 12, 23, 73
Cable Kit, spare part numbers
12, 23
Cable Retainer Kit, spare part
number 23
cables, service considerations 26
Cables/Connectors Kit, spare part
number 14, 23
Card Reader adapter, spare part
number 15, 21
card reader board
removal 88
spare part number 14, 23, 88
card reader cover
removal 82
spare part number 14, 23, 82

Card Reader Cover Kit, spare part
number 20
carrying case, spare part
numbers 17, 21, 23
components
bottom 7
front 4
rear 5
top 6
connectors, service
considerations 26
credit card reader
removal 80
spare part number 13, 23, 80
credit card reader board
removal 78
spare part numbers 13, 23,
78
D
display assembly
removal 30
spare part number 9, 24, 30
Display Cable Kit, spare part
number 9, 23, 37
display LVDS cable
removal 37
spare part number 9, 37
Display Panel Kit, spare part
number 9, 24, 30
display panel, product
description 1
docking connector 7
docking connector bracket
removal 60
spare part number 10, 60

Index

109

docking connector cable
removal 59, 87
spare part numbers 11, 24,
59, 87
docking station
illustrated 16
spare part number 16, 21
docking, product description 2
duck head power adapter
illustrated 19
spare part numbers 19, 24,
25
E
electrostatic discharge 27
equipment guidelines 29
Ethernet adapter cable, spare part
number 15, 21
Ethernet, product description 1
F
fingerprint reader
spare part number 23
fingerprint reader board
removal 89
spare part number 14, 89
forward-facing webcam
removal 57
spare part number 57
front components 4
front cover
removal 69, 84
spare part numbers 12, 14,
23, 69, 84
G
graphics, product description
grounding guidelines 27
guidelines
equipment 29
grounding 27
packaging 28
transporting 28
workstation 28

H
handle, spare part number 13,
22
HDMI/VGA adapter cable, spare
part number 15, 21
headphone jack 6
110

Index

HP ElitePad Service Tool, spare
part number 31
J
jacket cover, spare part numbers
22, 25
jacket keyboard, spare part
numbers 17, 21, 22
jacket, spare part numbers 17,
21
jacks
audio-in 6
audio-out 6
headphone 6
microphone 6
K
keyboard, product description 2
M
memory card reader slot/micro
SIM slot 5
memory, product description 1
micro SD Card Reader/micro SIM
slot access hole 5
microphone
location 7
product description 1
removal 43
spare part number 25, 43
microphone jack 6
Miscellaneous Rocker Button
Mounting Kit, spare part
number 13
Miscellaneous Rocker Button/
Mount Kit, spare part number
23
model name 1
N
NFC antenna
removal 38
spare part number 9, 24, 38
O
operating system, product
description 3
optical drive, product description
1

P
packaging guidelines 28
pen, spare part number 17, 24
plastic parts, service
considerations 26
pointing device, product
description 2
ports, product description 2
power button 7
power button actuator
installation 46
spare part number 9, 46
power button board
removal 45
spare part numbers 10, 24,
45
power components 19
power cord
set requirements 106
spare part numbers 16, 19,
20, 21
power requirements, product
description 2
primary storage, product
description 1
processor, product description 1
product description
audio 1
display panel 1
docking 2
Ethernet 1
external media cards 2
graphics 1
keyboard 2
memory 1
microphone 1
operating system 3
optical drive 1
pointing device 2
ports 2
power requirements 2
primary storage 1
processor 1
product name 1
security 3
sensors 2
video 1
wireless 1
product information 7
product name 1

R
rear components 5
rear cover, spare part numbers
13, 14, 23
rear-facing webcam
removal 44
spare part number 44
regulatory information 6, 7
removal/replacement procedures
30
Retail Jacket, spare part numbers
13, 22, 23
Rubber Kit, spare part numbers
13, 15, 23
S
Screw Kit, spare part numbers
13, 15, 18, 20, 23, 24
Security Jacket, spare part
numbers 14, 23
security, product description 3
sensors, product description 2
serial adapter cable, spare part
number 15, 21
service considerations
cables 26
connectors 26
plastic parts 26
service tag 8
service tool, spare part number
17, 21
SIM, spare part number 20, 21
slot cover
removal 58
spare part number 10, 58
Smart Card Reader Cover Kit,
spare part number 24
speakers
location 7
removal 65
spare part number 11, 24, 65
specifications 95
suction cup, spare part number
17, 21, 33
system board
removal 53, 76, 86
spare part numbers 10, 13,
14, 23, 24, 53, 76, 86

T
tablet
major components 9
specifications 95
Tape Support Kit, spare part
number 20, 25
tether, spare part number 22
tools required 26
top cap
removal 67, 82
spare part numbers 12, 14,
23, 67, 82
top components 6
TouchScreen cable
removal 37
spare part number 9, 37
transporting guidelines 28
U
USB adapter cable, spare part
number 15, 21
USB3 adapter, spare part
number 22

removal 61, 63
spare part numbers 10, 25,
61, 63
wireless, product description 1
WLAN antenna
location 4
removal 61
spare part numbers 61
WLAN module
removal 41
spare part number 11, 21, 41
workstation guidelines 28
WWAN antenna
location 4
WWAN module
removal 39
spare part numbers 10, 21,
22, 24, 39
WWAN/GPS auxiliary antenna
removal 63
spare part numbers 63

V
vibrator module
removal 50
spare part number 11, 24, 50
video, product description 1
volume button actuator
installation 48
spare part number 9, 48
volume button board
removal 47
spare part number 10, 25, 47
volume down 6
volume up button 6
W
webcam
location 4, 6
removal 44, 57
spare part numbers 10, 25,
44, 57
webcam status light 5
Webcam/Microphone Kit, spare
part number 10, 25
Windows button 5
wireless antenna
location 4

Index

111

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 120
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator                         : calvertc
Description                     : Cheetah tools build 11.7.1 created on November 22, 2011. 07:24 PM
Create Date                     : 2014:03:25 17:23:57-05:00
Creator Tool                    : AH Formatter V5.1 R1 (5,1,2009,0914) for Windows
Modify Date                     : 2014:03:25 17:23:57-05:00
Producer                        : Acrobat Distiller 10.0.0 (Windows)
Page Mode                       : UseOutlines
Author                          : calvertc
Subject                         : Cheetah tools build 11.7.1 created on November 22, 2011. 07:24 PM
Title                           :

EXIF Metadata provided by EXIF.tools

Hp Elitepad Mobile Pos G1 Solution Maintenance And Service Guide

Navigation menu

Versions of this User Manual:

Views

Navigation