Hp Enterprise Safety And Compliance Reference Guide Information For Server, Storage, Power, Networking, Rack Products
Hp-Integrity-Nonstop-Server-Safety-And-Compliance-Reference-Guide-669460 hp-integrity-nonstop-server-safety-and-compliance-reference-guide-669460
Hp-Networking-Safety-And-Compliance-Safety-And-Compliance-Information-168166 hp-networking-safety-and-compliance-safety-and-compliance-information-168166
Hp-Bladesystem-Safety-And-Compliance-Reference-Guide-669390 hp-bladesystem-safety-and-compliance-reference-guide-669390
2015-03-28
: Hp Hp-Enterprise-Safety-And-Compliance-Reference-Guide-669403 hp-enterprise-safety-and-compliance-reference-guide-669403 hp pdf
Open the PDF directly: View PDF 
.
Page Count: 29
| Download | |
| Open PDF In Browser | View PDF |
Safety and Compliance Information for Server, Storage, Power, Networking, and Rack Products Abstract This document contains safety precautions, environmental notices, and regulatory compliance notices for HP Enterprise products. HP Part Number: 703827-007 Published: December 2014 Edition: 7 © Copyright 2012, 2014 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Contents 1 Safety precautions......................................................................................5 General precautions.................................................................................................................5 Symbols on equipment..............................................................................................................5 Precautions for maintaining and servicing products.......................................................................6 Precautions for power products...................................................................................................7 Power cords........................................................................................................................7 Power supplies.....................................................................................................................8 Uninterruptible power supply (UPS) products............................................................................8 Power distribution units (PDUs)...............................................................................................9 Grounding........................................................................................................................10 Voltage selection...............................................................................................................11 Batteries...........................................................................................................................11 Fuse replacement...............................................................................................................11 Precautions for products installed in racks and cabinets...............................................................11 Precautions for modems, telecommunications, or LAN options......................................................12 2 Environmental notices................................................................................13 Waste Electrical and Electronic Equipment (WEEE) statements......................................................13 Battery replacement notices.....................................................................................................14 RoHS material content declarations...........................................................................................17 China RoHS material content declaration..............................................................................17 India RoHS material content declaration................................................................................17 Turkey RoHS material content declaration..............................................................................17 Ukraine RoHS material content declaration............................................................................17 Perchlorate material — Special handling may apply....................................................................17 European Union Commission Regulation 1275/2008..................................................................18 3 Regulatory compliance notices...................................................................19 Regulatory compliance identification numbers............................................................................19 Federal Communications Commission notice..............................................................................19 FCC rating label................................................................................................................19 Class A equipment........................................................................................................19 Class B equipment........................................................................................................19 Declaration of Conformity for products marked with the FCC logo (United States only)................20 Modification.....................................................................................................................20 Cables.............................................................................................................................20 Notices for Canada (Avis Canadien).........................................................................................20 Class A equipment.............................................................................................................20 Class B equipment.............................................................................................................20 Notices for China...................................................................................................................20 Class A equipment.............................................................................................................20 Trusted Platform Module (TPM) – China Import Restrictions.......................................................21 Notices for European Union.....................................................................................................21 European Union Regulatory Notice......................................................................................21 Products with wireless functionality (EMF)..............................................................................21 Notices for Japan...................................................................................................................22 VCCI notice......................................................................................................................22 Power cord statement..........................................................................................................22 Notices for Korea...................................................................................................................22 Class A equipment.............................................................................................................22 Class B equipment.............................................................................................................22 Notices for Taiwan.................................................................................................................23 Contents 3 BSMI notices.....................................................................................................................23 Class A EMI warning message........................................................................................23 UPS (less than 16A output current)...................................................................................23 UPS (greater than 16A output current)..............................................................................23 Belarus Kazakhstan Russia marking...........................................................................................23 Wireless devices.....................................................................................................................24 Brazilian notice.................................................................................................................24 Canadian notice................................................................................................................24 Japanese notice.................................................................................................................24 Mexican notice..................................................................................................................25 Taiwanese notice...............................................................................................................25 Laser compliance notices.........................................................................................................25 Index.........................................................................................................28 4 Contents 1 Safety precautions Retain and follow all product safety and operating instructions. Always refer to the documentation (printed or electronic) supplied with your product. If there is a conflict between this document and the product documentation, the product documentation takes precedence. Observe all warnings on the product and in the operating instructions to reduce the risk of bodily injury, electric shock, fire, and damage to the equipment. General precautions CAUTION: personnel. The installation and maintenance of products must be carried out by qualified If the product sustains damage requiring service, disconnect the product from the AC electrical outlet and refer servicing to an HP authorized service provider. Examples of damage requiring service include: • The power cord, extension cord, or plug has been damaged. • Liquid has been spilled on the product or an object has fallen into the product. • The product has been exposed to rain or water. • The product has been dropped or damaged. • The product does not operate normally when you follow the operating instructions. To reduce the risk of personal injury or damage to the product: • Place the product away from radiators, heat registers, stoves, amplifiers, or other products that produce heat. • Never use the product in a wet location. • Avoid inserting foreign objects through openings in the product. • Move products with casters carefully. Avoid quick stops and uneven surfaces. • Turn down the volume before using headphones or other audio devices. Symbols on equipment The following symbols may be placed on equipment to indicate the presence of potentially hazardous conditions: This symbol in conjunction with any of the following symbols indicates the presence of a potential hazard. The potential for injury exists if warnings are not observed. Consult your documentation for specific details. This symbol indicates the presence of hazardous energy circuits or electric shock hazards. Refer all servicing to qualified personnel. WARNING: To reduce the risk of injury from electric shock hazards, do not open this enclosure. Refer all maintenance, upgrades, and servicing to qualified personnel. This symbol indicates the presence of electric shock hazards. The area contains no user or field-serviceable parts. Do not open for any reason. WARNING: To reduce risk of injury from electric shock hazards, do not open this enclosure. General precautions 5 This symbol on an RJ-45 receptacle indicates a Network Interface Connection. WARNING: To reduce risk of electric shock, fire, or damage to the equipment, do not plug telephone or telecommunications connectors into this receptacle. This symbol indicates the presence of a hot surface or hot component. If this surface is contacted, the potential for injury exists. WARNING: To reduce the risk of injury from a hot component, allow the surface to cool before touching. This symbol indicates the presence of a moving fan blade. If the spinning blades are contacted, the potential for injury exists. WARNING: Hazardous moving parts. Keep away from moving fan blades. To reduce the risk of injury from a hot component, allow the surface to cool before touching. These symbols on power supplies or systems indicate that the equipment is supplied by multiple sources of power. WARNING: To reduce the risk of injury from electric shock, remove all power cords to completely disconnect power from the system. This symbol indicates that the component exceeds the recommended weight for one individual to handle safely. WARNING: To reduce the risk of personal injury or damage to the equipment, observe local occupational health and safety requirements and guidelines for manual material handling. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. To prevent damage, observe antistatic precautions. This symbol indicates the presence of a laser device in the product that may exceed Class 1 limits. Refer to the product documentation for more information. Precautions for maintaining and servicing products To reduce the risk of electric shock or damage to the equipment when installing, maintaining, or servicing products, observe the following precautions: 6 • Some products contain power supplies that are capable of producing hazardous energy levels. Refer to the documentation included with your product to determine whether it contains these power supplies. The installation of internal options and routine maintenance and service of this product should be performed by individuals who are knowledgeable about the procedures, precautions, and hazards associated with equipment containing hazardous energy levels. • Allow the product to cool before removing covers and touching internal components. • Do not use conductive tools that could bridge live parts. • Remove all watches, rings, or loose jewelry when working in hot-plug areas of an energized server and storage products. • Do not attempt to defeat safety interlocks (where provided). Safety precautions • Some products have covers or doors to access hot-plug components and may allow access to hazardous energy circuits or moving fans. ◦ The doors should remain locked during normal operation. OR ◦ The server should be installed in a controlled access location where only qualified personnel have access to the server. • Power down the equipment and disconnect all AC power cords before removing any access covers for non-hot-plug areas. • Do not replace non-hot-plug components while power is applied to the product. First, shut down the product and disconnect all AC power cords. • Do not exceed the level of repair specified in the procedures in the product documentation. All troubleshooting and repair procedures are detailed to allow only subassembly or module-level repair. Because of the complexity of the individual boards and subassemblies, do not attempt to make repairs at the component level or to make modifications to any printed wiring board. Improper repairs can create a safety hazard. • For floor-standing products, install and extend bottom stabilizers before installing options and boards. • Verify that the AC power supply branch circuit that provides power to the rack is not overloaded. This will reduce the risk of personal injury, fire, or damage to the equipment. The total rack load should not exceed 80 percent of the branch circuit rating. Consult the electrical authority having jurisdiction over your facility wiring and installation requirements. Precautions for power products Power cords To reduce the risk of electric shock or damage to the equipment: • Use an approved power cord. If you have questions about the type of power cord to use, contact your HP authorized service provider. • If you have not been provided with a power cord for your computer or for any AC-powered option intended for your product, purchase a power cord that is approved for use in your country. • You must use a power cord rated for your product and for the voltage and current marked on the electrical ratings label of the product. The voltage and current rating of the cord must be greater than the voltage and current rating marked on the product. • Do not place objects on AC power cords or cables. Arrange them so that no one may accidentally step on or trip over them. • Do not pull on a cord or cable. When unplugging from the electrical outlet, grasp the cord by the plug. • Make sure that the total ampere rating of all products plugged into an extension cord or power strip does not exceed 80 percent of the ampere ratings limit for the extension cord or power strip. • Do not disable the power cord grounding plug. The grounding plug is an important safety feature. • Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times. Precautions for power products 7 Power supplies Hot-plug power supplies are not designed to be removed or installed with AC power connected to the power supply. To reduce the risk of electric shock or damage to the equipment when handling hot-plug power supplies: • Install the power supply before connecting the power cord to the power supply. • Unplug the power cord before removing the power supply from the product. • If the system has multiple sources of power, you must unplug all AC power cords from the power supplies to completely disconnect power from the system. Verify that the external power source connected to your product matches the type of power source indicated on the electrical ratings label. If you are not sure of the type of power source required, consult your HP authorized service provider or local power company. Uninterruptible power supply (UPS) products • To reduce the risk of electric shock and/or equipment damage when installing or servicing UPS products: ◦ The installation of options and routine maintenance and service of UPS products must be performed by trained service technicians who are knowledgeable about the procedures, precautions, and hazards associated with AC power products. ◦ Hardwired UPS products require a direct connection to an AC branch circuit (AC mains). Connection should only be performed in accordance with National Electrical Code (NFPA70) Article 310 in North America or the equivalent local and national wiring regulations. ◦ Use a Lockout/Tagout procedure to isolate hardwired UPS products from AC power before servicing the product or replacing a non-hot-plug component. ◦ Do not operate a UPS that is disconnected from AC power. Use the TEST/ALARM RESET button to test the batteries. Disconnect all protected loads before disconnecting the UPS from AC power. ◦ Pluggable UPS products must be disconnected and unplugged from AC power before servicing the product or replacing a non-hot-plug component. ◦ Do not overload the output of the UPS. The total connected load should not exceed the rated output. ◦ To reduce the risk of electric shock due to high leakage currents, ensure that there is a reliable grounded (earthed) connection before connecting power distribution products to AC power. If a large number of products will be connected to a single UPS, it may be necessary to conduct an evaluation of the installation to verify the total amount of leakage current. The total combined leakage current should not exceed 5 percent of the input current for the UPS and associated load. 8 Safety precautions • • • ◦ For rack installations, do not exceed the maximum number of UPS products in any single equipment rack. ◦ For rack installations, install the UPS only at the bottom of a rack. To reduce the risk of personal injury or damage to equipment when installing a Remote Emergency Power Off (REPO) port: ◦ The REPO port must be wired by a licensed electrician. ◦ Verify that the main AC power disconnect device for the UPS is locked and/or tagged in the OFF position before wiring the REPO port. ◦ In North America, the REPO circuit must comply with the NEC (NFPA 70, Article 725) for a Class 2 circuit. In other geographical regions or countries, the REPO port wiring must comply with the national and local standards in the area in which the product is installed. To reduce the risk of personal injury from electric shock or damage to equipment when installing or servicing batteries: ◦ Make sure that only trained service personnel handle or connect the batteries. ◦ Remove watches, rings, or other metal objects prior to working with the equipment. ◦ Use tools with insulated handles. ◦ On products with remote external batteries, do not attempt to replace batteries unless all battery circuit breakers are in the OFF (down) position. These are hazardous voltage batteries. This product may contain sealed lead-acid batteries. To reduce the risk of fire or chemical burns: ◦ Do not attempt to recharge batteries after they have been removed from the equipment. ◦ Do not disassemble, crush, or puncture the batteries. ◦ Do not short the external contacts of the batteries. ◦ Do not immerse the batteries in water. ◦ Do not expose the batteries to temperatures higher than 60°C or dispose of in fire. ◦ Use only the HP spare battery designated for this equipment. Power distribution units (PDUs) To reduce the risk of electric shock and/or equipment damage when installing or servicing PDUs: • The installation and routine maintenance and service of PDUs must be performed by trained service technicians who are knowledgeable about the procedures, precautions, and hazards associated with AC power products. • Hardwired PDUs require a direct connection to an AC branch circuit (AC mains). Connection should only be performed in accordance with National Electrical Code (NFPA70 Article 310) in North America, or in other regions or countries, in accordance with the equivalent local and national wiring regulations. • A reliable grounded (earthed) connection should be checked before connecting PDUs. • Use a Lockout/Tagout procedure to isolate hardwired PDUs from AC power before servicing or replacing the product. Precautions for power products 9 • Pluggable PDUs must be disconnected from the product and unplugged from the AC electrical outlet before servicing or replacing the product. • Do not overload the output of PDUs. The total connected load should not exceed rated input power. • To reduce the risk of electric shock due to high leakage currents, ensure that there is a reliable grounded (earthed) connection before connecting power distribution products to AC power. If a large number of products will be connected to a single PDU, it may be necessary to conduct an evaluation of the installation to verify the total amount of leakage current. The total combined leakage current should not exceed 5 percent of the input current for the PDU and associated load. Grounding Depending on the product model, your product will be classified either as a safety Class I or safety Class II-compliant device. Class I devices require a connection to earth ground (3-terminal plug); Class II devices incorporate a 2-terminal plug. • Class I: There must be an uninterruptible safety earth ground from the main power source to the product's power cord or supplied power cord set. Whenever it is likely that the protection has been impaired, disconnect the power cord until the ground has been restored. • Class II: Safety Class II-compliant devices include supplemental insulation to protect against electric shock, and do not require a connection to earth ground. For LAN connections: • If your LAN covers an area served by more than one power distribution system, be sure their safety grounds are securely interconnected. • LAN cables may occasionally be subject to hazardous transient voltages (such as lightning or disturbances in the electrical utilities power grid). Handle exposed metal components of the network with caution. • This product and all interconnected equipment must be installed indoors within the same building, including all associated LAN connections as described by Environment A of the IEEE 802.3af standard. Earth leakage current To reduce the risk of electric shock due to high leakage currents, ensure that there is a reliable grounded (earthed) connection before connecting power distribution products to AC power. Observe the following limits when connecting the product to AC power distribution devices: • For UPS products and PDUs that have attached AC power cords or are directly wired to the building power, the total combined leakage current should not exceed 5 percent of the rated input current for the device. • For UPS products and PDUs that have detachable AC power cords, the total combined leakage current should not exceed 3.5mA. Electrostatic discharge (ESD) When handling any electronic component or assembly (such as a PCI card or memory DIMM), you must observe the following antistatic precautions to prevent damage. An ESD kit (HP P/N A3024-80004) is available (or supplied with memory additions). This kit contains one wrist strap, one conductive sheet, and one antistatic foam pad. 10 • Always disconnect power from the server and wear a grounded wrist strap when working around the server. • Always wear a grounded wrist strap when handling printed circuit boards. Safety precautions • Treat all assemblies, components, and interface connections as static sensitive. • Avoid working in carpeted areas and keep body movement to a minimum while removing or installing boards to minimize buildup of static charge. Voltage selection • On products that have voltage select switches, make sure that the switch is set for the type of voltage you use (115 VAC or 230 VAC). • Do not attempt to power the product with voltage converter kits sold for appliances. Batteries WARNING! Some HP products may contain internal replaceable battery cells or battery packs. There is risk of fire and burns if the battery pack is not handled properly. To reduce the risk of personal injury: • Do not attempt to recharge the battery. • Do not disassemble, crush, puncture, short external contacts, or dispose of the battery in fire or water. • Replace only with the HP spare battery designated for this product. Dispose of used batteries according to the manufacturer's instructions and local disposal requirements. • For battery holders (for example, coin cells), observe the correct polarity when changing the battery/cell. There is a danger of explosion if the battery is installed incorrectly. Fuse replacement CAUTION: For continued protection against risk of fire, replace fuses only with fuses of the same type and the same rating. Disconnect power before changing fuses. Precautions for products installed in racks and cabinets Materials handling To reduce the risk of personal injury or damage to the equipment: • Observe local occupational health and safety requirements and guidelines for handling materials. • Obtain assistance to lift and stabilize the product during installation or removal. • Remove all pluggable power supplies and modules to reduce the weight of the product. • Be careful when pressing the rail release latches and sliding the product into the rack. The slide rails could pinch your fingertips. Rack stability To reduce the risk of personal injury or damage to the equipment, the rack must be secured adequately to prevent it from becoming unstable and/or falling over. • Extend the leveling jacks to the floor. • Ensure that the full weight of the rack rests on the leveling jacks. • Install stabilizing feet on the rack. • In a multiple-rack installation, fasten the racks together securely. • Extend only one rack component at a time. Racks can become unstable if more than one component is extended. Precautions for products installed in racks and cabinets 11 • Load the rack from the bottom up, starting with the heaviest component. • Ensure that the component is properly mated with the rails, or the rails may be unstable. • Do not attempt to move a fully loaded rack. Remove components from the rack before moving it. • Do not attempt to move a rack on an incline that is greater than 10 degrees from horizontal. Cabinet safety WARNING! Cabinets are heavy even when empty. Exercise caution when moving cabinets whether equipment is installed in the cabinet or not. Avoid rolling cabinets on rough or uneven surfaces or inclines greater than 10 degrees. Unloading cabinets from the pallet and movement of cabinets should be performed by at least two people. Slideable products are not to be extended from the cabinet while the equipment is on the shipping pallet. The cabinet must be unloaded from the pallet and all anti-tip devices properly installed prior to extending any slideable product. Once installed, all anti-tip devices must remain in place to maintain stability. Only one slideable product must be extended at a time. Failure to follow these precautions can result in damage to equipment or injury to personnel. Precautions for modems, telecommunications, or LAN options To reduce the risk of exposure to shock from telephone ringing voltages: 12 • Do not connect or use a modem or telephone (other than a cordless type) during a lightning storm. • Do not use a telephone line to report a gas leak while you are in the vicinity of the leak. • Do not connect or use a modem or telephone cable in a wet location. • Disconnect the modem cable before opening a product enclosure, touching or installing internal components, or touching an uninsulated modem cable or jack. • Do not plug telecommunications or telephone connectors into the NIC receptacles. Safety precautions 2 Environmental notices HP is committed to providing our customers with information about the chemical substances in our products as needed to comply with legal requirements such as REACH (Regulation EC No 1907/2006 of the European Parliament and the Council). A chemical information report for this product can be found at http://www.hp.com/go/reach. For HP product environmental and safety information and compliance data, including RoHS and REACH, see www.hp.com/go/ecodata. For HP environmental information, including company programs, product recycling, and energy efficiency, see www.hp.com/environment. Waste Electrical and Electronic Equipment (WEEE) statements Country EU WEEE Directive Page Austria http://h41111.www4.hp.com/globalcitizenship/at/de/environment/recycle/hardwarerecycle.html Belgium (FR) http://h41111.www4.hp.com/globalcitizenship/be/fr/environment/recycle/hardwarerecycle.html Belgium (NL) http://h41111.www4.hp.com/globalcitizenship/be/nl/environment/recycle/hardwarerecycle.html Bulgaria http://h41111.www4.hp.com/globalcitizenship/bg/bg/environment/recycle/hardwarerecycle.html Czech Republic http://h41111.www4.hp.com/globalcitizenship/cz/cs/environment/recycle/hardwarerecycle.html Denmark http://h41111.www4.hp.com/globalcitizenship/dk/da/environment/recycle/hardwarerecycle.html Estonia http://h41111.www4.hp.com/globalcitizenship/ee/et/environment/recycle/hardwarerecycle.html Finland http://h41111.www4.hp.com/globalcitizenship/fi/fi/environment/recycle/hardwarerecycle.html France http://h41111.www4.hp.com/globalcitizenship/fr/fr/environment/recycle/hardwarerecycle.html Germany http://h41111.www4.hp.com/globalcitizenship/de/de/environment/recycle/hardwarerecycle.html Greece http://h41111.www4.hp.com/globalcitizenship/gr/el/environment/recycle/hardwarerecycle.html Hungary http://h41111.www4.hp.com/globalcitizenship/hu/hu/environment/recycle/hardwarerecycle.html Ireland http://h41111.www4.hp.com/globalcitizenship/ie/en/environment/recycle/hardwarerecycle.html Italy http://h41111.www4.hp.com/globalcitizenship/it/it/environment/recycle/hardwarerecycle.html Latvia http://h41111.www4.hp.com/globalcitizenship/lv/lv/environment/recycle/hardwarerecycle.html Lithuania http://h41111.www4.hp.com/globalcitizenship/lt/lt/environment/recycle/hardwarerecycle.html Luxembourg http://h41111.www4.hp.com/globalcitizenship/be/fr/environment/recycle/hardwarerecycle.html Malta http://h41111.www4.hp.com/globalcitizenship/uk/en/environment/recycle/hardwarerecycle.html Netherlands http://h41111.www4.hp.com/globalcitizenship/nl/nl/environment/recycle/hardwarerecycle.html Norway http://h41111.www4.hp.com/globalcitizenship/no/no/environment/recycle/hardwarerecycle.html Poland http://h41111.www4.hp.com/globalcitizenship/pl/pl/environment/recycle/hardwarerecycle.html Portugal http://h41111.www4.hp.com/globalcitizenship/pt/pt/environment/recycle/hardwarerecycle.html Romania http://h41111.www4.hp.com/globalcitizenship/ro/ro/environment/recycle/hardwarerecycle.html Slovakia http://h41111.www4.hp.com/globalcitizenship/sk/sk/environment/recycle/hardwarerecycle.html Slovenia http://h41111.www4.hp.com/globalcitizenship/si/sl/environment/recycle/hardwarerecycle.html Spain http://h41111.www4.hp.com/globalcitizenship/es/es/environment/recycle/hardwarerecycle.html Waste Electrical and Electronic Equipment (WEEE) statements 13 Country EU WEEE Directive Page Sweden http://h41111.www4.hp.com/globalcitizenship/se/sv/environment/recycle/hardwarerecycle.html Switzerland (DE) http://h41111.www4.hp.com/globalcitizenship/ch/de/environment/recycle/hardwarerecycle.html Switzerland (FR) http://h41111.www4.hp.com/globalcitizenship/ch/fr/environment/recycle/hardwarerecycle.html United Kingdom http://h41111.www4.hp.com/globalcitizenship/uk/en/environment/recycle/hardwarerecycle.html Battery replacement notices Batteries, battery packs, and accumulators should not be disposed of together with the general household waste. To forward them to recycling or proper disposal, use the public collection system or return them to HP, an authorized HP Partner, or their agents. For more information about battery replacement or proper disposal, contact an authorized reseller or an authorized service provider. 14 Environmental notices Battery replacement notices 15 16 Environmental notices RoHS material content declarations China RoHS material content declaration Chinese version: http://www8.hp.com/us/en/hp-information/environment/chinarohs.html English version: http://www8.hp.com/us/en/hp-information/environment/chinarohs-english.html India RoHS material content declaration This product complies with the "India E-waste (Management and Handling) Rule 2011" and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule. Turkey RoHS material content declaration Türkiye Cumhuriyeti: EEE Yönetmeliğine Uygundur Ukraine RoHS material content declaration Обладнання відповідає вимогам Технічного регламенту щодо обмеження використання деяких небезпечних речовин в електричному та електронному обладнанні, затвердженого постановою Кабінету Міністрів України від 3 грудня 2008 № 1057 Perchlorate material — Special handling may apply Perchlorate material - special handling may apply. See http://www.dtsc.ca.gov/hazardouswaste/ perchlorate/. This product’s real-time clock battery or coin cell battery may contain perchlorate and may require special handling when recycled or disposed of in California. RoHS material content declarations 17 European Union Commission Regulation 1275/2008 The power data for affected products—including the power consumption of the product in networked standby if all wired network ports are connected and all wireless network ports are activated—is provided in section P14, “Additional information,” of the product IT ECO Declaration available at http://www.hp.com/hpinfo/globalcitizenship/environment/productdata/iteconetworking.html. 18 Environmental notices 3 Regulatory compliance notices Regulatory compliance identification numbers For the purpose of regulatory compliance certifications and identification, this product has been assigned a unique regulatory model number. The regulatory model number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to this regulatory model number. The regulatory model number is not the marketing name or model number of the product. Federal Communications Commission notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules. These rules place computers and related peripheral devices into two classes, A and B, depending upon their intended installation. Class A devices are those that may reasonably be expected to be installed in a business or commercial environment. Class B devices are those that may reasonably be expected to be installed in a residential environment (for example, personal computers). The FCC requires devices in both classes to bear a label indicating the interference potential of the device as well as additional operating instructions for the user. FCC rating label The FCC rating label on the device shows the classification (A or B) of the equipment. Class B devices have an FCC logo or ID on the label. Class A devices do not have an FCC logo or ID on the label. After you determine the class of the device, refer to the corresponding statement. Class A equipment This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at personal expense. Class B equipment This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit that is different from that to which the receiver is connected. • Consult the dealer or an experienced radio or television technician for help. Regulatory compliance identification numbers 19 Declaration of Conformity for products marked with the FCC logo (United States only) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For questions regarding this product, contact us by mail or telephone: • Hewlett-Packard Company P. O. Box 692000, Mail Stop 530113 Houston, Texas 77269-2000 • 1-800-HP-INVENT (1-800-474-6836) For continuous quality improvement, calls may be recorded or monitored. For questions regarding this FCC declaration, contact us by mail or telephone: • Hewlett-Packard Company P. O. Box 692000, Mail Stop 510101 Houston, Texas 77269-2000 • 1-281-514-3333 To identify the product, refer to the part, series, or model number found on the product. Modification The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the user's authority to operate the equipment. Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and Regulations. Notices for Canada (Avis Canadien) Class A equipment This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. CAN ICES-3(A)/NMB-3(A) Cet appareil numérique de la class A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Class B equipment This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. CAN ICES-3(B)/NMB-3(B) Cet appareil numérique de la class B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Notices for China Class A equipment 20 Regulatory compliance notices Trusted Platform Module (TPM) – China Import Restrictions HP SPECIAL REMINDER: Before enabling TPM functionality on this system, you must ensure that your intended use of TPM complies with relevant local laws, regulations and policies, and approvals or licenses must be obtained if applicable. For any compliance issues arising from your operation/usage of TPM which violates the above mentioned requirement, you shall bear all the liabilities wholly and solely. HP will not be responsible for any related liabilities. Notices for European Union European Union Regulatory Notice Products bearing the CE marking comply with one or more of the following EU Directives as may be applicable: • Low Voltage Directive 2006/95/EC • EMC Directive 2004/108/EC • Ecodesign Directive 2009/125/EC • R&TTE Directive 1999/5/EC • RoHS Directive 2011/65/EU Compliance with these directives is assessed using applicable European Harmonised Standards. The full Declaration of Conformity can be found at the following website: http://www.hp.eu/ certificates. (Search with the product model name or its Regulatory Model Number (RMN), which may be found on the regulatory label.) The point of contact for regulatory matters is Hewlett-Packard GmbH, Dept./MS:HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, GERMANY. Products with wireless functionality (EMF) This product meets international guidelines (ICNIRP) for exposure to radio frequency radiation. This product may incorporate a radio transmitting and receiving device. For server computers and wireless access points, a separation distance of 20 cm between the body of the user and the antenna ensures that the RF exposure levels comply with the EU requirements. Restrictions for product with wireless functionality This product is designed for use without restrictions in all EU countries, plus Iceland, Liechtenstein, Norway, and Switzerland. Notices for European Union 21 Notices for Japan VCCI notice Power cord statement Notices for Korea Class A equipment Class B equipment 22 Regulatory compliance notices Notices for Taiwan BSMI notices Class A EMI warning message UPS (less than 16A output current) UPS (greater than 16A output current) Belarus Kazakhstan Russia marking Manufacturer and Local Representative Information Manufacturer’s information: • Hewlett-Packard Company, 3000 Hanover Street, Palo Alto, California 94304, U.S. Local Representative information Russian: • HP Russia: ЗАО “Хьюлетт-Паккард А.О.”, 125171, Россия, г. Москва, Ленинградское шоссе, 16А, стр.3, тел/факс: +7 (495) 797 35 00, +7 (495) 287 89 05 • HP Belarus: ИООО «Хьюлетт-Паккард Бел», 220030, Беларусь, г. Минск, ул. Интернациональная, 36-1, офис 722-723, тел.: +375 (17) 392 28 18, факс: +375 (17) 392 28 21 • HP Kazakhstan: ТОО «Хьюлетт-Паккард (К), 050040, Казахстан, г. Алматы, Бостандыкский район, ул. Тимирязева, 28В, 1 этаж, тел./факс: +7 (727) 355 35 50, +7 (727) 355 35 51 Notices for Taiwan 23 Local Representative information Kazakh: • HP Kazakhstan: ЖШС «Хьюлетт-Паккард (К)», Қазақстан, Алматы қ., Бостандық ауданы, Тимирязев к-сі, 28В, тел./факс: +7 (727) 355 35 50, +7 (727) 355 35 51 Manufacturing date: The manufacturing date is defined by the serial number. CCSYWWZZZZ (HP serial number format for this product) Valid date formats include: • YWW, where Y indicates the year counting from within each new decade, with 2000 as the starting point; for example, 238: 2 for 2002 and 38 for the week of September 9. In addition, 2010 is indicated by 0, 2011 by 1, 2012 by 2, 2013 by 3, and so forth. • YYWW, where YY indicates the year, using a base year of 2000; for example, 0238: 02 for 2002 and 38 for the week of September 9. Wireless devices In some environments, the use of wireless devices might be restricted. Such restrictions might apply on airplanes, in hospitals, near explosives, or in other hazardous locations. Before you turn on this product, be sure that you understand local policies and have proper authorization. WARNING! Exposure to Radio Frequency Radiation: The radiated output power of this device is below the FCC radio exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact during normal operation is minimized. To avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antennas should not be less than 20 cm (8 inches) during normal operation. Brazilian notice Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário. Canadian notice Wireless operation is subject to two conditions. The first is that the wireless device may not cause interference. The second is that the wireless device must accept any interference, including interference that may cause undesired operation of the device. Japanese notice 24 Regulatory compliance notices Mexican notice La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada. Taiwanese notice Laser compliance notices This device may contain a laser that is classified as a Class 1 Laser Product in accordance with U.S. FDA regulations and the IEC 60825-1. The product does not emit hazardous laser radiation. WARNING! Use of controls or adjustments or performance of procedures other than those specified herein or in the laser product's installation guide may result in hazardous radiation exposure. To reduce the risk of exposure to hazardous radiation: • Do not try to open the module enclosure. There are no user-serviceable components inside. • Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified herein. • Allow only HP Authorized Service technicians to repair the unit. The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration implemented regulations for laser products on August 2, 1976. These regulations apply to laser products manufactured from August 1, 1976. Compliance is mandatory for products marketed in the United States. Laser compliance notices 25 26 Regulatory compliance notices Laser compliance notices 27 Index B G batteries replacement notices, 14 safety precautions, 9, 11 Belarus Kazakhstan Russia EAC marking, 23 BSMI notices, 23 grounding earth leakage current, 10 ESD, 10 safety precautions, 10 C laser compliance notices, 25 cabinet safety, 12 CE compliance marking European Union Regulatory Notice, 21 China import restrictions Trusted Platform Module (TPM), 21 China RoHS material content declaration, 17 D Declaration of Conformity European Union Regulatory Notice, 21 products marked with FCC logo (U.S. only), 20 E EAC marking Belarus Kazakhstan Russia, 23 earth leakage current, 10 electromagnetic interference (EMI) cable connector hoods, 20 electrostatic discharge (ESD), 10 EMC compliance notices, 19 EMF (electromagnetic fields) European Union Regulatory Notice, 21 environmental notices, 13 battery replacement and disposal, 14 European Union Commission Regulation 1275/2008, 18 perchlorate, 17 REACH, 13 RoHS, 13 WEEE, 13 equipment symbols, 5 ESD kit, 10 EuroAsian Economic Commission (EAC), 23 European Union Commission Regulation 1275/2008, 18 European Union Regulatory Notice CE compliance marking, 21 Declaration of Conformity, 21 products with wireless functionality (EMF), 21 F FCC notice, 19 FCC rating label, 19 Class A equipment, 19 Class B equipment, 19 fuse replacement, 11 28 Index L M maintaining and servicing products safety precautions, 6 materials handling products installed in racks and cabinets, 11 modems safety precautions, 12 P perchlorate material safety precautions, 17 power cords safety precautions, 7 power distribution units (PDUs) safety precautions, 9 power supplies safety precautions, 8 products installed in racks and cabinets materials handling, 11 safety precautions, 11 products with wireless functionality (EMF), 21 R rack stability, 11 radio frequency (RF) emission limits FCC notice, 19 radio frequency interference (RFI) cable connector hoods, 20 REACH, 13 recycling notices, 13 regulatory compliance identification numbers, 19 regulatory compliance notices, 19 BSMI, 23 Canada (Avis Canadien), 20 China, 20 European Union, 21 FCC, 19 identification numbers, 19 Japan, 22 Korea, 22 laser notices, 25 recycling notices, 13 Taiwan, 23 WEEE statements, 13 wireless devices, 24 regulatory model number, 19 Remote Emergency Power Off (REPO) port safety precautions, 9 RoHS material content declarations China, 17 Turkey, 17 Ukraine, 17 S safety precautions, 5 batteries, 9, 11 cabinets, 12 fuse replacement, 11 general, 5 grounding, 10 maintaining and servicing products, 6 modems, 12 modems, telecommunications, or LAN options, 12 PDUs, 9 power cords, 7 power products, 7 power supplies, 8 products installed in racks and cabinets, 11 REPO port, 9 telecommunications equipment, 12 UPS, 8 voltage selection, 11 substances environmental notices, 13 perchlorate material, 17 RoHS material content declarations, 17 symbols on equipment, 5 T telecommunications equipment safety precautions, 12 Trusted Platform Module (TPM) China import restrictions, 21 Turkey RoHS material content declaration, 17 U Ukraine RoHS material content declaration, 17 UPS products safety precautions, 8 V VCCI notice, 22 voltage selection, 11 W WEEE statements, 13 wireless devices, 24 Brazilian notice, 24 Canadian notice, 24 electromagnetic fields (EMF), 21 Japanese notice, 24 Mexican notice, 25 Taiwanese notice, 25 29
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Page Mode : UseOutlines XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Format : application/pdf Title : Safety and Compliance Information for Server, Storage, Power, Networking, and Rack Products Creator : Hewlett-Packard Company Subject : safety, precautions, regulations, regulatory compliance notices, reference, alerts, prevention, server, storage, power, networking, symbols, power, disposal, stability, racks, cabinets, rails, environment, batteries, modems, telecommunications, LAN, WEEE, RoHS, perchlorate, FCC, wireless, laser, BSMI, TPM, European Union Commission Regulation 1275/2008 Keywords : "safety, precautions, regulations, regulatory compliance notices, reference, alerts, prevention, server, storage, power, networking, symbols, power, disposal, stability, racks, cabinets, rails, environment, batteries, modems, telecommunications, LAN, WEEE, RoHS, perchlorate, FCC, wireless, laser, BSMI, TPM, European Union Commission Regulation 1275/2008" Producer : XEP 4.18 build 20100322 Trapped : False Creator Tool : Unknown Create Date : 2014:12:10 20:30:27Z Modify Date : 2014:12:17 11:05:10-05:00 Metadata Date : 2014:12:17 11:05:10-05:00 Document ID : uuid:d73672c1-7086-4b2f-a933-c3d1ccb9b4e6 Instance ID : uuid:4e209a79-8fc8-4d7a-a539-34347a0c84c6 Has XFA : No Page Count : 29 Author : Hewlett-Packard CompanyEXIF Metadata provided by EXIF.tools