Hp Jetdirect Ew2500 802 11B G Wireless Print Server Setup And Install 802.11g Guide ENWW

HP Jetdirect ew2500 802.11g Wireless Print Server Setup Guide c01893278

JetDirect Ew2500 c01893278

2015-03-28

: Hp Hp-Jetdirect-Ew2500-802-11B-G-Wireless-Print-Server-Setup-And-Install-669147 hp-jetdirect-ew2500-802-11b-g-wireless-print-server-setup-and-install-669147 hp pdf

Open the PDF directly: View PDF PDF.
Page Count: 58

HP Jetdirect ew2500
802.11g Wireless Print Server
Setup Guide
HP Jetdirect ew2500 802.11g Wireless Print
Server
Setup Guide
© 2004-2014 Copyright Hewlett-Packard
Development Company, L.P.
Reproduction, adaptation or translation
without prior written permission is prohibited,
except as allowed under the copyright laws.
The information contained herein is subject
to change without notice.
The only warranties for HP products and
services are set forth in the express warranty
statements accompanying such products
and services. Nothing herein should be
construed as constituting an additional
warranty. HP shall not be liable for technical
or editorial errors or omissions contained
herein.
Applicable products: J8021A
Edition 2, 11/2014
Microsoft®, MS-DOS®, Windows®,
Microsoft Windows NT® are trademarks or
U.S. registered trademarks of Microsoft
Corporation. IBM®, AIX® are registered
trademarks of International Business
Machines Corp. Ethernet is a registered
trademark of Xerox Corporation.
PostScript® is a trademark of Adobe
Systems, Incorporated. UNIX® is a
registered trademark of the Open Group.
Windows Vista™ is either a registered
trademark or trademark of Microsoft
Corporation in the United States and/or other
countries.
Table of contents
1 Introduction
What's in the box .................................................................................................................................. 1
What you need to supply ...................................................................................................................... 2
Test button functions ............................................................................................................................ 3
Wireless LAN terms and concepts ...................................................................................................... 4
Access Point ........................................................................................................................ 4
Ad Hoc (peer-to-peer) mode ................................................................................................ 5
Channels .............................................................................................................................. 5
Encryption ............................................................................................................................ 6
Infrastructure mode .............................................................................................................. 6
Security type ........................................................................................................................ 7
Service Set Identifiers (SSID) .............................................................................................. 8
Signal range ......................................................................................................................... 8
Network printing terms and concepts .................................................................................................. 8
Client-server printing ............................................................................................................ 8
Peer-to-peer (direct mode) printing ...................................................................................... 9
Network protocols ................................................................................................................ 9
Network address .................................................................................................................. 9
Hardware address ............................................................................................................... 9
If you need help... ................................................................................................................................. 9
2 Install the print server hardware
Set up the printer ................................................................................................................................ 11
If the printer is already set up ............................................................................................ 11
If the printer is not already set up ...................................................................................... 11
Connect the print server to the printer ............................................................................... 11
3 Make a network connection
Configure a wireless network using the network (LAN) cable ............................................................ 13
Use a Microsoft Windows wireless PC .............................................................................. 14
Configure settings for a wired network ............................................................................................... 17
Use an Apple Macintosh wireless computer ...................................................................................... 18
Configure a wireless network without a network (LAN) cable ............................................................ 18
Factory-default wireless settings ....................................................................................... 20
ENWW iii
Optional wireless connection setup methods ..................................................................................... 21
4 Install the printer on a network system or server
Microsoft client-server networks ......................................................................................................... 26
5 Troubleshooting
Reset the print server to factory defaults (“cold reset”) ...................................................................... 28
Interpret the status lights .................................................................................................................... 29
Unable to communicate with the print server (wireless) ..................................................................... 31
During initial setup ............................................................................................................. 31
After initial setup ................................................................................................................ 31
My configured channel does not match the configuration page ......................................................... 32
Improve reception and performance .................................................................................................. 32
Firmware download failure ................................................................................................................. 33
Appendix A Service and support
Hewlett-Packard limited warranty statement ...................................................................................... 34
Your authorized dealer ...................................................................................................... 35
Service billing (out of warranty) ......................................................................................... 35
Service outside the USA .................................................................................................... 36
Local warranty statements ................................................................................................................. 36
Australia and New Zealand ................................................................................................ 36
Customer support ............................................................................................................................... 36
HP support online .............................................................................................................. 36
HP support by phone ......................................................................................................... 36
Product accessibility ........................................................................................................................... 36
Appendix B Solution summary
HP support software ........................................................................................................................... 37
Embedded services ............................................................................................................................ 37
Supported network protocols .............................................................................................................. 38
Appendix C Specifications
Electrical (power adapter) .................................................................................................................. 40
Environmental .................................................................................................................................... 41
Electromagnetic .................................................................................................................................. 41
Acoustic .............................................................................................................................................. 41
Radio characteristics .......................................................................................................................... 42
iv ENWW
HP subassemblies ............................................................................................................. 42
Channel frequencies .......................................................................................................... 42
Safety ................................................................................................................................................. 42
Wireless telecommunications ............................................................................................................. 42
Appendix D Regulatory statements
FCC statement ................................................................................................................................... 43
Regulatory Model Identification Number ............................................................................................ 44
Canada ............................................................................................................................................... 44
VCCI (Japan) ...................................................................................................................................... 44
RRL statement (Korea) ...................................................................................................................... 44
Regulatory wireless statements ......................................................................................................... 45
Exposure to radio frequency radiation ............................................................................... 45
Notice to users in Argentina ............................................................................................... 45
Notice to users in Brazil ..................................................................................................... 45
Notice to users in Canada ................................................................................................. 46
European Union regulatory notice ..................................................................................... 46
Notice to users in Indonesia .............................................................................................. 47
Notice to users in Korea .................................................................................................... 47
Notice to users in Mexico ................................................................................................... 47
Notice to users in Pakistan ................................................................................................ 47
Notice to users in Singapore .............................................................................................. 47
Notice to users in South Africa .......................................................................................... 47
Notice to users in Taiwan .................................................................................................. 48
ENWW v
vi ENWW
1 Introduction
Thank you for purchasing the HP Jetdirect ew2500 802.11g Wireless Print Server! This print server
complies with IEEE 802.11g wireless standards.
Use the HP Jetdirect ew2500 802.11g Wireless Print Server to directly connect your compatible HP
printer to your network using either a wired or wireless connection.
●What's in the box
●What you need to supply
●Test button functions
●Wireless LAN terms and concepts
●Network printing terms and concepts
●If you need help...
What's in the box
1USB cable
2Network (LAN) cable
3External power adapter
4HP Jetdirect ew2500 802.11g Wireless Print Server
*Warranty card (where applicable)
ENWW What's in the box 1
What you need to supply
●A supported Microsoft Windows or Apple Macintosh computer with the included Network (LAN)
cable to configure wired and/or wireless settings.
For a wireless network: an 802.11b or 802.11g wireless LAN (WLAN) interface card installed in the
computer.
NOTE: Use the included LAN cable to avoid possible radio interference problems during
installation. After installation, you can remove the cable.
◦Microsoft Windows XP, Vista, Server 2003, or Server 2008.
◦Apple Mac OS X 10.2 and later.
◦UNIX/Linux: Hewlett-Packard HP-UX, Sun Microsystems Solaris, IBM AIX, HP MPE-i, RedHat
Linux, SuSE Linux
If your network is entirely wireless, then a wireless computer is needed to set up a wireless
connection from your printer to your network.
●For wireless infrastructure mode only: a wireless router, access point, or Apple base station.
In infrastructure mode, an access point is a device that connects wireless devices, such as a
wireless network printer, to your cabled network. See Wireless LAN terms and concepts
on page 4 for more information.
●For Windows systems: the printer’s software driver for your Windows system.
You can obtain your printer driver from one of the following sources:
◦printing system CD-ROM supplied with your printer
◦HP support Web site at: www.hp.com/go/support.
2 Chapter 1 Introduction ENWW
Test button functions
The test button, which is located on the back of the HP Jetdirect ew2500 print server, provides various
functions depending on the number of the times the button is pressed. These functions can be useful
during the installation process.
NOTE: Typically, you press the button the indicated number of times in quick succession. However,
some options provide additional functionality when holding the last button press.
Table 1-1 Test button instructions
Button Presses Function Instructions and Status Light (if applicable)
1Print an HP Jetdirect configuration
page.
Changes to blinking green for approximately five seconds.
2Print an HP Jetdirect security page.
3Print an HP Jetdirect configuration
page in English, French, Italian,
German, or Spanish.
On the third press, hold the button down until the status light begins
blinking, and then release the button. The configuration page prints
in all languages.
4Print an HP Jetdirect wireless status
page.
5Change the LAN speed/handshake.
This is only for switches that do not
have auto negotiation mode set,
Select from the following speeds/
handshake: 10 Mbps. half-duplex, 10
Mbps. full-duplex, 100 Mbps. half-
duplex, or 100 Mbps. full-duplex.
On the fifth press, hold the button down until the status light begins
blinking, then release the button.
Select from the following speed/handshake combinations (displayed
three times):
●Blinking amber — 10 half-duplex
●Solid amber — 10 full-duplex
●Blinking green — 100 half-duplex
●Solid green — 100 full-duplex
To select a speed/handshake:
1. Press and release the test button when the color associated with
the speed/handshake you want is displayed. (The test button
turns off then displays the selected color.)
2. If the speed is correct (indicated by the test button color), press
and release the test button once to confirm.
3. If the speed/handshake is not correct (indicated by the test
button color), do not press the test button. The change is not
made. You can then start over and change the speed/
handshake.
4. To complete (save) the change, power cycle the print server.
6Reset 802.1x to factory default
values.
To complete (save) the change, power cycle the print server.
7 Disable IPsec. To complete (save) the change, power cycle the print server.
ENWW Test button functions 3
Wireless LAN terms and concepts
Access Point
An Access Point is a device that typically serves as a bridge or gateway between wireless devices and
the devices on a cabled network. An Access Point must be able to receive and forward network traffic
between wireless and cabled network devices. Multiple Access Points can act as repeaters to extend
the range of a wireless network.
Connecting via an access point is called Infrastructure Mode. On Apple networks, this is called Airport
Network Mode.
Figure 1-2 Access Point in enterprise workgroup
Figure 1-3 Residential gateway as Access Point
4 Chapter 1 Introduction ENWW
Figure 1-4 Access Point as wireless repeater
Ad Hoc (peer-to-peer) mode
Ad Hoc mode (or peer-to-peer mode) is a wireless network topology where wireless devices
communicate with each other directly. An Access Point is not used. On Apple networks, Ad Hoc mode
is called computer-to-computer mode.
NOTE: Ad Hoc mode is not as reliable as Infrastructure mode, and if used, should be limited to six
devices or less.
When set in this mode, the HP Jetdirect print server receives print jobs from wireless computers directly.
Figure 1-5 Ad Hoc mode: a peer-to-peer wireless network topology
NOTE: The term “peer-to-peer” might have a different meaning depending on its usage. While Ad Hoc
peer-to-peer mode refers to a wireless network topology, HP Jetdirect peer-to-peer printing refers to a
direct print path from a network computer to a printer. HP Jetdirect peer-to-peer printing can be used
on both Ad Hoc or Infrastructure wireless topologies.
Channels
IEEE standards for 802.11b and 802.11g wireless LANs specify a spectrum of radio waves for wireless
communications. The allowed spectrum is divided into channels consisting of 22 MHz each. The number
ENWW Wireless LAN terms and concepts 5
of available channels authorized for use may be restricted based on your location (see Radio
characteristics on page 42).
●If the print server is powered on and discovers a wireless network whose SSID (network name) is
also “hpsetup”, it will automatically adjust its channel to match that network.
●If the print server is reconfigured for Infrastructure mode, it will automatically adjust its channel to
match the Access Point.
Encryption
Wireless networks use radio signals for network communications, which can be easily monitored by
someone eavesdropping on the network. To deter eavesdropping and to help ensure data privacy,
encryption of wireless communications may be used.
For HP Jetdirect print servers in their factory-default state, encryption of wireless communications is
disabled. However, the print servers support static WEP and popular dynamic encryption protocols.
NOTE: Wireless performance may be reduced when using encryption keys due to the additional
processing time required.
Static Encryption. WEP encryption protocols were developed to provide a basic level of data privacy.
WEP protocols use static encryption keys to encrypt and decrypt wireless communications.
NOTE: WEP encryption levels are sometimes called 40-bit, 64-bit, 104-bit, or 128-bit encryption. Both
40-bit and 64-bit encryption are really the same, as are 104-bit and 128-bit encryption. When entering
WEP keys, the user specifies 40 bits for 64-bit encryption, or 104 bits for 128-bit encryption. An additional
24 initialization vector (IV) bits are automatically added for a total of 64 bits and 128 bits, respectively.
In this guide, we will use “40/64-bit” and “104/128bit” to specify these WEP encryption levels.
For basic encryption, static WEP keys are configured on each device on the wireless network. WEP
keys are considered static because they remain the same unless manually reconfigured. For example,
on a typical Infrastructure mode network that uses static WEP encryption, a change to the WEP key on
an Access Point will require a manual change to the WEP key on each wireless device.
HP Jetdirect wireless print servers support configuration of up to four static WEP keys, for either 40/64-
bit or 104/128-bit encryption.
Dynamic Encryption. For advanced encryption methods, dynamic encryption protocols are used. For
dynamic encryption protocols, encryption keys are automatically changed at routine intervals making
them difficult to decipher.
Dynamic encryption protocols, such as dynamic WEP and wi-fi protected access (WPA/WPA2), provide
a more secure wireless environment.
When configured for WPA/WPA2–Personal authentication, HP Jetdirect print servers use WPA
encryption.
Infrastructure mode
Infrastructure mode is a wireless network topology where all wireless communications go through an
Access Point. Infrastructure mode is called a Basic Service Set (BSS), and sometimes referred to as
“enterprise mode.” On Apple networks, Infrastructure mode is called Airport Network mode. When set
6 Chapter 1 Introduction ENWW
in this mode, the HP Jetdirect print server receives print jobs from wireless and cabled network
computers through an Access Point.
Figure 1-6 Infrastructure mode: a wireless topology that uses an Access Point for connection to a wired
network
Security type
Security is used to validate the identification of each device or computer that is attempting to access a
network. The security type used on a network is determined during network design and depends on the
network security requirements. Consequently, security methods are closely associated with encryption
options that are also used on the network.
HP Jetdirect wireless print servers support the following security types:
●No security. No encryption or authentication is used. Open system. Your wireless network does
not require device authentication or security to access the network. However, your network might
use WEP encryption keys for data privacy.
●WEP-Personal. Each device on your wireless network uses a shared encryption key (a shared
password value) for network access and communication. Each device on the network must use
the same key. The HP Jetdirect print server supports IEEE 802.11 WEP keys for encrypted network
communications.
●WEP-Enterprise. The network uses WEP with EAP/802.1x authentication. This type of security
utilizes a central authentication server, such as RADIUS, to authenticate users on the network. The
HP Jetdirect print server supports these server-based authentication protocols: LEAP, PEAP, and
EAP-TLS.
●WPA/WPA2–Personal. Your network uses wi-fi protected access (WPA) with a pre-shared key
that is typically generated by a pass-phrase. WPA encryption is normally used for wireless
communication and offers improved security.
●WPA/WPA2–Enterprise. Your network uses WPA with EAP/802.1x authentication. This type of
security utilizes a central authentication server, such as RADIUS, to authenticate users on the
network. The HP Jetdirect print server supports these server-based authentication protocols:
LEAP, PEAP, and EAP-TLS.
ENWW Wireless LAN terms and concepts 7
Service Set Identifiers (SSID)
An SSID is a logical name assigned to a wireless LAN. It is typically used to provide LAN access control.
For example, if the SSID for a wireless network is “mycompany”, then each wireless device on this
network must be configured with this SSID.
In infrastructure mode, the Access Point will require wireless devices to be configured with the
appropriate SSID before network access is allowed.
Signal range
The range over which wireless devices can communicate depends on the physical environment and the
orientation of the HP Jetdirect print server.
For 802.11g, the range is typically 50 feet at the highest data rate (54 Mbps). Data rate will decrease to
802.11b levels as range, traffic and interference increase.
For 802.11b, the range is typically 100 feet at the highest data rate (11 Mbps), and 300 feet at the lowest
data rate (1 Mbps).
In general, while radio waves can bounce off obstacles to access print servers, it is best to have clear
line-of-sight access between devices without obstacles through which the signal must pass.
NOTE: Signal range and wireless transmission performance is reduced with increasing distance
between devices, and with obstacles that block or absorb signals.
Network printing terms and concepts
Client-server printing
On a client-server network, client computers send print jobs to a dedicated network server that controls
the use of each installed printer. The HP Jetdirect print server receives print jobs over the network under
the network server’s control, or can automatically monitor print queues and de-spool print jobs from the
network server.
Figure 1-7 Client-server printing (in Infrastructure mode)
8 Chapter 1 Introduction ENWW
Peer-to-peer (direct mode) printing
On a peer-to-peer network, dedicated network servers are not used. Instead, an HP Jetdirect-connected
network printer is installed on each client computer that will send print jobs directly to the printer.
Figure 1-8 Peer-to-peer printing
Network protocols
For network computers and printers to communicate on a network, they must use a common language,
or network protocol. The HP Jetdirect print server can support many different network protocols
simultaneously, such as TCP/IP (Transmission Control Protocol/Internet Protocol) and IPX (Internet
Packet Exchange). For a list of supported protocols, see Supported network protocols on page 38.
TCP/IP is the most commonly used protocol in most network environments.
Network address
Each device on a network must be identified by a unique network address for the specific network
protocol used. On an IPX network, the network address is assigned automatically. On an IP network,
configuration and assignment of IP addresses and other IP settings are a bit more complex. Network
addresses are configured and stored on each HP Jetdirect print server during installation, and are listed
on the HP Jetdirect configuration page for the print server.
Hardware address
Each device on a network contains a unique LAN hardware (or “station”) address that is assigned by
the manufacturer of the device. Because the HP Jetdirect print server connects printers to a network,
each print server contains a LAN hardware address assigned by Hewlett-Packard.
The address consists of 12 hexadecimal digits (0 through F). The first 6 digits uniquely identify the
manufacturer, and the second 6 digits uniquely identify the device.
The LAN hardware address is important because it may be needed to identify the printer during
installation. It is listed on the HP Jetdirect configuration page for each print server. In addition, it is listed
on a label attached to the print server.
If you need help...
Go to http://www.hp.com/support/net_printing and select your JetDirect model for more information.
ENWW If you need help... 9
10 Chapter 1 Introduction ENWW
2 Install the print server hardware
Set up the printer
NOTE: Do not install any printer software until all of the hardware connection steps have been
completed.
If the printer is already set up
1. Turn off the printer.
2. Detach it from any computer.
3. Turn on the printer.
4. Proceed to Connect the print server to the printer on page 11.
If the printer is not already set up
1. Assemble the hardware only using the instructions supplied with the printer.
2. Set aside the printer CD. (Do not install its software yet. Do not attach the printer to your computer.)
3. Turn on the printer.
4. Print a test page as instructed.
Connect the print server to the printer
1. Connect the USB cable.
●Plug the supplied USB cable into the USB connector on the back of the print server.
●Plug the other end of the cable into the printer’s USB connector.
CAUTION: Do not use a USB hub, extender or parallel converter.
ENWW Set up the printer 11
2. Connect the power cable.
●Plug the supplied power module into a power outlet.
●Plug the other end of the power cable into the power connector on the back of the print server.
3. Print a configuration page by pressing the test button once. (The test button is located on the back
of the HP Jetdirect ew2500 print server.)
4. Proceed to Make a network connection on page 13.
12 Chapter 2 Install the print server hardware ENWW
3 Make a network connection
This section describes how to configure the HP Jetdirect ew2500 802.11g Wireless Print Server with
either a wired or wireless network connection to your network.
NOTE: You can use a wired network connection to configure either wired or wireless settings. HP
recommends that you use a wired connection to configure wireless settings.
Configuration procedures:
●To configure wireless settings using the included network (LAN) cable, go to Configure a wireless
network using the network (LAN) cable on page 13.
●To configure settings for a wired network, go to Configure settings for a wired network
on page 17.
●To configure settings for an Apple Macintosh wireless computer, go to Use an Apple Macintosh
wireless computer on page 18.
●To configure wireless settings without a network (LAN) cable, go to Configure a wireless network
without a network (LAN) cable on page 18.
●For optional methods, go to Optional wireless connection setup methods on page 21.
Configure a wireless network using the network (LAN)
cable
For wireless operation, the print server needs to be connected to your wireless network before you can
discover and install the printer on your PC or other network system.
You can configure the wireless settings with the included network (LAN) cable, which can be removed
after you have completed configuring the wireless settings.
NOTE: HP recommends that you configure the wireless settings using a network (LAN) cable (wired).
Although you can configure without a network cable (wireless), it is generally easier to configure using
the included network (LAN) cable.
After connecting the cable, allow up to 30 seconds for the cable connection to be enabled. When
disconnecting the cable after configuration, allow up to 30 seconds for the wireless connection to enable
automatically.
ENWW Configure a wireless network using the network (LAN) cable 13
To configure a wireless connection using a network (LAN) cable, verify the following:
●You have a computer with one of the following operating systems:
◦Microsoft Windows XP, Vista, Server 2003, or Server 2008.
◦Apple Mac OS X 10.2 or greater.
●You have installed the HP Jetdirect print server hardware and have printed an HP Jetdirect
configuration page.
●(Infrastructure mode only) The wireless router, access point, or Apple base station on your network
is operating properly.
CAUTION: If you reset the print server to factory-default values after you configure a wireless network
connection, the network connection will be lost. To reestablish a connection, you must reconfigure the
print server.
14 Chapter 3 Make a network connection ENWW
ENWW Configure a wireless network using the network (LAN) cable 15
16 Chapter 3 Make a network connection ENWW
Configure settings for a wired network
A network connection is required before you can discover and install the printer on your network
systems. To configure a wired connection, verify the following:
●You have a computer with one of the following operating systems:
◦Microsoft Windows XP, Vista, Server 2003, or Server 2008.
◦Apple Mac OS X 10.2 or greater.
●You have installed the HP Jetdirect print server hardware and have printed an HP Jetdirect
configuration page.
ENWW Configure settings for a wired network 17
Set up each Windows computer for printing on the networked printer by inserting the CD-ROM and
selecting Install. This basic procedure involves configuring network parameters for the print server,
installing printer drivers and other software, and setting up the print path.
To use the wizard to install the networked printer on this computer, return to the initial screen for this
CD, select Install, and follow the instructions. Help is included. When finished there, this computer is
ready to use the printer.
NOTE: Making network address changes might break the print path set up by the wizard if the printer
has been previously installed on the computer.
18 Chapter 3 Make a network connection ENWW
ENWW Configure a wireless network without a network (LAN) cable 19
Factory-default wireless settings
The HP Jetdirect print server wireless factory-default settings are shown in the following table.
20 Chapter 3 Make a network connection ENWW
Table 3-1 Factory default wireless settings
Parameter Settings Comments
Communications Mode Ad Hoc If your network uses a wireless router,
access point, or Apple base station,
reconfigure the Communications Mode
of the HP Jetdirect print server to
Infrastructure.
Channel 11 (Ad Hoc mode only) Specifies the
broadcast channel if the print server fails
to connect to a network. In most cases,
you will not need to change this setting.
The print server scans all available
channels for the specified network and
adapts its channel to the one detected.
Network Name (SSID) hpsetup Change the SSID on the print server to
match your network. The SSID is case
sensitive.
Authentication Open System The HP Jetdirect print server is not
configured for network authentication. If
required by your network, the proper
authentication method must be
configured on the HP Jetdirect print
server.
Encryption (WEP) [Disabled] If your network uses WEP encryption
keys, configure the encryption keys on
the print server. You can configure up to
four WEP keys. The active key must
match the value and active key position
(for example, Key 1) configured on other
wireless devices.
Optional wireless connection setup methods
To use Telnet or the HP embedded Web server, first reconfigure your wireless computer to communicate
using the HP Jetdirect factory-default settings, and then create an IP path to the default IP address
(check the HP Jetdirect configuration page for the IP address assigned on the print server). To create
an IP path, use one of the following methods:
●If supported, use a “route add” command from your system prompt (see your system help or
documentation).
●Temporarily reconfigure your computer’s IP address to match the default IP network of the
HP Jetdirect print server. For example, if the print server IP address is 169.254.111.111, you could
use 169.254.111.112 for your computer. Before modifying your computer’s settings, you should
record your current settings, or if possible, create a new profile for your temporary settings.
ENWW Optional wireless connection setup methods 21
Optional methods to configure a wireless network connection include:
●Using a Telnet session with the HP Jetdirect print server to configure selected wireless parameters
(not all wireless parameters can be set through Telnet). For information on available Telnet
commands, use the Telnet help command.
●Using your Web browser to access the HP embedded Web server on the HP Jetdirect wireless
print server.
22 Chapter 3 Make a network connection ENWW
4 Install the printer on a network system
or server
Once your printer is connected to your network (wired or wireless), you can install the printer on the
dedicated print server.
●Microsoft client-server networks
ENWW Before you begin... 23
24 Chapter 4 Install the printer on a network system or server ENWW
ENWW Microsoft networks 25
Microsoft client-server networks
After you have set up the printer on the server, set up your network clients to access the printer through
the server. The procedures depend on the utilities available for your particular clients and network
operating system.
For example, if the printer is installed and shared on a Microsoft server, each Windows client can use
Add Printer or Network Neighborhood utilities to access the printer.
For more information, refer to the documentation and help supplied with your network operating system.
26 Chapter 4 Install the printer on a network system or server ENWW
ENWW To view documents on the CD-ROM 27
5 Troubleshooting
This section provides basic troubleshooting information.
●Reset the print server to factory defaults (“cold reset”)
●Interpret the status lights
●Unable to communicate with the print server (wireless)
●My configured channel does not match the configuration page
●Improve reception and performance
●Firmware download failure
To troubleshoot your HP Jetdirect print server, you may need the following items:
●An HP Jetdirect Configuration Page
●A Printer Configuration or Diagnostic Page
●Documentation that came with your printer
●The diagnostics tools and utilities provided with your network software (for example, TCP/IP
utilities, or network printer management applications such as HP Web Jetadmin)
NOTE: Frequently asked questions about installing and configuring the HP Jetdirect print server can
be found by searching for your HP Jetdirect product at: www.hp.com/support/net_printing.
Reset the print server to factory defaults (“cold reset”)
Once you have configured the HP Jetdirect print server, your settings are saved in memory even over
power cycles.
If you lose communications with the HP Jetdirect print server, or it fails to operate properly, you might
need to reset the print server to its factory-default configuration. This is called a cold reset.
28 Chapter 5 Troubleshooting ENWW
CAUTION: Resetting the HP Jetdirect wireless print server to factory-default settings can cause the
print server to lose its wireless connection to your network. Reconfiguration of wireless network settings
and reinstallation of the print server might be required.
If a printer reset is required, settings are reset to their factory default values. If you reset the printer, you
might need to reconfigure the printer’s settings that are required by users.
To restore factory-default settings on an HP Jetdirect ew2500 print server, follow these steps:
1. Unplug the power module from the back of the print server.
2. While holding down the test button on the back of the print server, plug the power module back
into the print server then release the test button. Any user-configured settings will be erased.
When you restore the print server to its factory-default settings, you should print an HP Jetdirect
configuration page to confirm that factory-default values have been assigned.
Interpret the status lights
The HP Jetdirect ew2500 status lights provide information about the USB, wired, and wireless
connections. The Link and Act status lights on the LAN connector indicate network activity.
1USB
2Wired
3Wireless
4Link (on LAN connector)
5 Act (on LAN connector)
ENWW Interpret the status lights 29
Table 5-1 HP Jetdirect ew2500 802.11g Wireless Print Server status lights
Light State Color Description
USB Solid Green USB cable connected, fully
operational.
Off —USB cable not connected, not
operational.
Solid Yellow Error condition.
Blinking Green Software attention.
Yellow Hardware attention.
Wired Off —●Initializing.
●Being used in a wireless
configuration.
●Power is off.
Solid Green Link exists, good signal
strength.
Flickering Green Network activity, good signal
strength.
Blinking (fast) Green Test Button pressed, good
signal.
Wireless Off —●Initializing.
●Being used in a wired
configuration.
●Power is off.
Blinking (slow) Blue Running a self test, scanning,
or there is no link.
Solid Blue Wireless link exists, good
signal strength.
Amber Wireless link exists, weak
signal strength.
Flickering Blue Network activity, good signal
strength.
Amber Network activity, weak signal
strength.
Blinking (fast) Blue Test Button pressed, good
signal.
Amber Test Button pressed, weak
signal.
Link Solid Green Successfully linked to the
network.
Off —No link.
Act Solid Yellow Network transmission activity.
Off — No activity.
30 Chapter 5 Troubleshooting ENWW
Unable to communicate with the print server (wireless)
During initial setup
Verify the following:
●Your wireless computer is configured to match the default wireless network settings on the
HP Jetdirect print server:
◦Communication Mode: Ad Hoc
◦Network Name (SSID): hpsetup
◦Encryption (WEP): [Disabled]
NOTE: The Network Name (SSID) is case-sensitive.
If the configuration settings are incorrect, connecting to the network might fail.
If the connection fails after entering configuration settings, reset the print server to factory-default
settings (“cold reset”) and try again.
●The HP Jetdirect print server is turned on and operating properly (print an HP Jetdirect configuration
page).
●You are within range of the HP Jetdirect print server.
●There are fewer than six devices total on the Ad Hoc network (with SSID “hpsetup”).
●There is no Access Point in the vicinity that is configured with an SSID of “hpsetup.”
●(For Telnet or HP embedded Web server access) Multiple print servers are not being configured
at the same time. If there are, turn all off except the one you want to configure.
After initial setup
If you have successfully configured the HP Jetdirect wireless print server with a network connection to
your network, but your network computers are unable to communicate with the printer (including a “ping”
command), try the following:
●Print an HP Jetdirect configuration page and verify all configuration settings for your network.
Common errors include incorrect entries for the following items:
◦Communication Mode (Ad Hoc or Infrastructure)
◦Network Name (SSID), which is case-sensitive
◦Authentication method
◦Encryption level, encryption key entries, or the specified transmit key
ENWW Unable to communicate with the print server (wireless) 31
◦IP address
◦BSSID (Basic Service Set Identifier), which distinguishes one wireless LAN from another even
though they have the same SSID.
●Verify that the printer is within range of the network. See Improve reception and performance
on page 32 for more information.
●Use a wireless PC and its utilities to confirm the signal strength at the printer’s location. The
detected signal strength should be similar for the print server, as indicated on the HP Jetdirect
configuration page.
My configured channel does not match the configuration
page
(Ad Hoc mode only) The HP configuration tools allow you to select channel 10 (default) or 11 on the
HP Jetdirect wireless print server. This channel is only used by the print server to broadcast its Network
Name (SSID) if it fails to detect and join an existing wireless network. If it is able to join a network, it will
reconfigure its channel to the one used by the network.
The HP Jetdirect configuration page will identify the network channel actually being used on a network.
It does not show the broadcast channel used when a network is not detected.
Improve reception and performance
Wireless LAN radio signals can penetrate many indoor structures and can reflect around obstacles.
However, wireless communication range and performance depends on a variety of factors, including
the number of users, the quality and physical placement of the wireless hardware, and the sources of
radio signal interference (for example, microwave ovens and cordless telephones use similar
frequencies that may interfere with wireless LAN signals). In general, the HP Jetdirect wireless print
server data transfer rates will decrease with increasing distance, obstructions and interference.
For these symptoms
●Wireless status light is amber.
●The signal strength is poor or marginal.
●Print jobs are excessively slow.
32 Chapter 5 Troubleshooting ENWW
Try these actions
●Reorient the HP Jetdirect print server's location in relation to the Access Point or wireless PC. This
might improve reception and performance.
●Reduce or remove sources of interference. Metallic objects can absorb or attenuate radio signals,
and devices such as microwave ovens and cordless phones operate using similar radio
frequencies.
●Reduce the distance between the printer and the Access Point or wireless PC. This can be
accomplished by:
◦moving the print server
◦moving the Access Point or wireless PC
◦adding an additional Access Point (Infrastructure mode only)
●Elevate the Access Point’s antenna. In most office environments, elevating the Access Point’s
antenna will improve the range and performance of all wireless devices.
Firmware download failure
The HP Jetdirect ew2500 print server provides limited firmware upgrade capabilities. As with other
HP Jetdirect print servers, firmware upgrades may be downloaded as available using tools such as HP
Download Manager (Windows), HP Web Jetadmin, HP embedded Web server, or FTP (File Transfer
Protocol).
If the firmware download fails to complete, you should restart the download without cycling power to the
print server.
If power is lost during the download and the print server must be restarted, your next steps depend on
whether the print server is configured for server-based authentication.
ENWW Firmware download failure 33
A Service and support
●Hewlett-Packard limited warranty statement
●Local warranty statements
●Customer support
●Product accessibility
Hewlett-Packard limited warranty statement
HP product Duration of limited warranty
HP Jetdirect ew2500 print server 1 Year
HP warrants to you, the end-user customer, that HP hardware and accessories will be free from defects
in materials and workmanship after the date of purchase, for the period specified above. If HP receives
notice of such defects during the warranty period, HP will, at its option, either repair or replace products
which prove to be defective. Replacement products may be either new or equivalent in performance to
new.
HP warrants to you that HP software will not fail to execute its programming instructions after the date
of purchase, for the period specified above, due to defects in material and workmanship when properly
installed and used. If HP receives notice of such defects during the warranty period, HP will replace
software which does not execute its programming instructions due to such defects.
HP does not warrant that the operation of HP products will be uninterrupted or error free. If HP is unable,
within a reasonable time, to repair or replace any product to a condition as warranted, you will be entitled
to a refund of the purchase price upon prompt return of the product.
HP products may contain remanufactured parts equivalent to new in performance or may have been
subject to incidental use.
Warranty does not apply to defects resulting from (a) improper or inadequate maintenance or calibration,
(b) software, interfacing, parts or supplies not supplied by HP, (c) unauthorized modification or misuse,
(d) operation outside of the published environmental specifications for the product, or (e) improper site
preparation or maintenance.
TO THE EXTENT ALLOWED BY LOCAL LAW, THE ABOVE WARRANTIES ARE EXCLUSIVE AND
NO OTHER WARRANTY OR CONDITION, WHETHER WRITTEN OR ORAL, IS EXPRESSED OR
IMPLIED AND HP SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OR CONDITIONS OF
34 Appendix A Service and support ENWW
MERCHANTABILITY, SATISFACTORY QUALITY, AND FITNESS FOR A PARTICULAR PURPOSE.
Some countries/regions, states or provinces do not allow limitations on the duration of an implied
warranty, so the above limitation or exclusion might not apply to you. This warranty gives you specific
legal rights and you might also have other rights that vary from country/region to country/region, state
to state, or province to province.
HP's limited warranty is valid in any country/region or locality where HP has a support presence for this
product and where HP has marketed this product. The level of warranty service you receive may vary
according to local standards. HP will not alter form, fit or function of the product to make it operate in a
country/region for which it was never intended to function for legal or regulatory reasons.
TO THE EXTENT ALLOWED BY LOCAL LAW, THE REMEDIES IN THIS WARRANTY STATEMENT
ARE YOUR SOLE AND EXCLUSIVE REMEDIES. EXCEPT AS INDICATED ABOVE, IN NO EVENT
WILL HP OR ITS SUPPLIERS BE LIABLE FOR LOSS OF DATA OR FOR DIRECT, SPECIAL,
INCIDENTAL, CONSEQUENTIAL (INCLUDING LOST PROFIT OR DATA), OR OTHER DAMAGE,
WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. Some countries/regions, states or
provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
THE WARRANTY TERMS CONTAINED IN THIS STATEMENT, EXCEPT TO THE EXTENT
LAWFULLY PERMITTED, DO NOT EXCLUDE, RESTRICT OR MODIFY AND ARE IN ADDITION TO
THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE SALE OF THIS PRODUCT TO YOU.
Your authorized dealer
If you encounter difficulty, begin by contacting the person who sold you the HP Jetdirect print server to
you. Your HP authorized dealer will be familiar with your requirements and can provide assistance.
During the warranty period, HP will replace the unit at no charge provided the defective unit is returned.
You may return the unit to your HP authorized dealer or your local HP sales and service office
representative. Be sure to include a copy of your purchase receipt.
For warranty service on HP Jetdirect products, call HP support. When calling, please have the following
information ready:
●HP Jetdirect product you are calling about.
●Model number of the product.
●Serial number of the product.
●Complete description of the problem.
●Proof of purchase of your product.
●Your shipping address.
The HP support representative will help you with troubleshooting, and advise you on warranty service.
Service billing (out of warranty)
When ordering a replacement unit for out-of-warranty service, you may be charged a repair cost. See
your HP authorized dealer or your local HP sales and service office representative. Or, you can call HP
at (800) 227-8164 (USA only).
ENWW Hewlett-Packard limited warranty statement 35
Service outside the USA
Customers outside the USA should contact their HP authorized dealer or HP sales and service office
to obtain information on prices, exchange unit availability and instructions.
Local warranty statements
Australia and New Zealand
For consumer transactions in Australia and New Zealand: The warranty terms contained herein except
to the extent lawfully permitted, do not exclude, restrict, or modify and are in addition to the mandatory
statutory rights applicable to the sale of this product to you.
Customer support
For warranty information, see Hewlett-Packard limited warranty statement on page 34.
HP support online
Click your way to a quick solution! The HP Web site at www.hp.com/support/net_printing is a great place
to start for information about your HP Jetdirect print server – 24 hours a day, 7 days a week.
For the latest HP Jetdirect installation software and documentation, visit www.hp.com/go/inpw_sw.
For the latest firmware for your HP Jetdirect print server, visit www.hp.com/go/webjetadmin_firmware.
HP support by phone
Highly trained technicians are ready to take your call.
For toll-free phone support in the USA and Canada, call HP support at: 1-800-HPINVENT
(1-800-474-6836)
For the most recent HP support telephone numbers and available services worldwide, visit www.hp.com/
support.
NOTE: The phone numbers listed may not be toll-free. Telephone fees are the responsibility of the
caller. Rates may vary. Contact your local telephone company for current rates.
Product accessibility
For information on our commitment to accessibility of HP Jetdirect print server products:
●Visit the HP Web site at www.hp.com/accessibility.
●Send an email message to: accessibility@hp.com.
36 Appendix A Service and support ENWW
B Solution summary
●HP support software
●Embedded services
●Supported network protocols
HP support software
Table B-1 HP support software
●HP Web Jetadmin software (TCP/IP and IPX networks)
●HP embedded Web server
●HP network printing setup software
◦HP LaserJet Utility for Macintosh (Mac OS)
Embedded services
Key services embedded in the HP Jetdirect ew2500 print server are listed below. For the latest features
and services, visit www.hp.com/go/jetdirect.
Table B-2 Embedded services
●Configuration and management
◦BootP/DHCP (IPv4 only)
◦DHCPv6
◦TFTP (IPv4 only)
◦Web Proxy (Automatic/Manual cURL)
◦LLMNR
◦Telnet (IPv4 only)
◦SNMP (v1, v2c, v3) agents
◦Bonjour (for Mac OS X)
◦FTP (File Transfer Protocol)
◦WS Discovery (Microsoft Web Services)
ENWW HP support software 37
◦HP embedded Web server, HTTP (TCP port 80)
◦HP embedded Web server, HTTPS (TCP port 443)
◦IP Security (IPsec)
◦Fleet configuration
●Printing
◦Raw IP printing (HP-proprietary TCP ports 9100, 9101, 9102)
◦LPD printing (TCP port 515)
◦IPP printing (TCP port 631)
◦FTP printing (TCP ports 20, 21)
◦WS Print (Microsoft Web Services)
●Security
◦SNMP v3
◦SSL/TLS
◦802,1X authentication: WEP, WPA, WPA2, LEAP, PEAP, and EAP-TLS
◦Firewall
●Supported Web browsers (for HP embedded Web server)
◦Microsoft Internet Explorer 6.x and higher
◦Firefox 2.x and higher
◦Opera 9.0 and higher
◦Safari 2.0 and higher
Supported network protocols
The supported network protocols, and popular network printing environments that use those protocols,
are listed below.
Table B-3 Supported network protocols
Supported network
protocols
Typical network printing environments
1
TCP/IPv4 (Direct Mode printing) Microsoft Windows XP (32-bit and 64-bit), Vista (64-bit), Server 2003 (32-bit and
64-bit), and Server 2008 (32-bit and 64-bit)
Microsoft Terminal Server and Citrix MetaFrame environments
2
Novell NetWare
2
5, 6.x
Mac OS 10.2 and later
UNIX and Linux, including: Hewlett-Packard HP-UX 10.2, 11.x, 11.i, Sun Microsystems Solaris 2.5 and
later (SPARCsystems only), IBM AIX 3.2.5 and later
2
, HP MPE-iX
2
, RedHat Linux 7.x and later
2
, SuSE
Linux 8.x and later
2
LPR/LPD (Line Printer Daemon, RFC 1179–compliant) systems
2
38 Appendix B Solution summary ENWW
Supported network
protocols
Typical network printing environments
1
IPP (Internet Printing Protocol)
FTP (File Transfer Protocol) printing
TCP/IPv6 Microsoft Windows XP (32-bit and 64-bit), Vista (64-bit), Server 2003 (32-bit and 64-bit), and Server
2008 (32-bit and 64-bit), Direct Mode port 9100 printing (Requires HP IPv6/IPv4 port monitor software
running on the system.)
Mac OS 10.2 and later
LPR/LPD (Line Printer Daemon, RFC 1179–compliant) systems with IPv6 client support
IPP (Internet Printing Protocol) systems with IPv6 client support
FTP (File Transfer Protocol) printing
IPX/SPX and
compatible
Novell NetWare 5, 6.x
2
Microsoft Windows XP (32-bit only), Direct Mode printing
Other protocols Novell NetWare NDS, Bindery, NDPS, and iPrint
DLC/LLC DLC/LLC protocols are provided for legacy systems that may require support
2
AppleTalk Mac OS
1Refer to the current HP Jetdirect product data sheets for additional network systems and versions. For operation with other
network environments, consult your system vendor or authorized HP dealer.
2Contact your network system vendor for software, documentation, and support.
Table B-3 Supported network protocols (continued)
ENWW Supported network protocols 39
C Specifications
●Electrical (power adapter)
●Environmental
●Electromagnetic
●Acoustic
●Radio characteristics
●Safety
●Wireless telecommunications
Electrical (power adapter)
The following lists the power adapters for the HP Jetdirect ew2500 print server.
Power Adapters for J8021A
Location Power Adapter* Power Cord Assembly**
USA and Canada, Latin America 120
Vac (except as noted below)
0957-2228 None
0957-2229 8121-1023
Latin America 100-240 Vac (except as
noted below), Continental Europe
(except as noted below), South Korea
0957-2229 8121-1015
Denmark 0957-2229 8121-1011
Chile 0957-2229 8121-1012
India 0957-2229 8121-1013
Brazil 0957-2229 8121-1014
Australia and New Zealand 0957-2229 8121-1016
United Kingdom, Ireland, Hong Kong
SAR, Singapore
0957-2229 8121-1017
Japan 0957-2229 8121-1018
China 0957-2229 8121-1019
Taiwan 0957-2229 8121-1020
Argentina 0957-2229 8121-1021
40 Appendix C Specifications ENWW
Power Adapters for J8021A
Location Power Adapter* Power Cord Assembly**
Switzerland 0957-2229 8121-1022
South Africa 0957-2229 8121-1028
Israel 0957-2229 8121-1032
Malaysia 0957-2229 8121-1017
* 0957-2228 Power adapter, AC-DC, 15W, USA wall adapter. 0957-2229 and 0957-2234 power adapter, AC-DC, 15W,
Universal In-Line adapter.
** 3-conductor, 0.5 meter power cords. For optional power cord lengths, contact HP Support.
Environmental
Operating Non-Operating
Temperature 0° to 55° C
(32° to 131° F)
-40° to 70° C
(-40° to 158° F)
Relative humidity (non-
condensing)
15% to 95% at 40° C (104° F) 15% to 95% at 65° C (149° F)
Maximum altitude 4.6 km (15,000 ft) 4.6 km (15,000 ft)
Electromagnetic
●FCC Title 47 CFR Part 15 Class B for Ethernet (USA)
●ICES-003 Class B (Canada)
●VCCI Class B (Japan)
●AS/NZS3548 Class B (Australia, New Zealand)
●CISPR-22 Class B (1997)* (International, Europe)
●CNS 13438 Class B (Taiwan)
●Korean EMI Law, No. 1996-98 Class B (Korea)
Acoustic
Not applicable.
ENWW Environmental 41
Radio characteristics
HP subassemblies
The HP Jetdirect ew2500 print server is designed for operation with radio frequencies in the license-
free 2.4 GHz band. However, due to local radio regulations and restrictions, the radio characteristics of
your particular HP Jetdirect print server can vary according to the location in which the product is used.
Channel frequencies
The channel frequencies are listed below:
Channel Frequency (MHz) Channel Frequency (MHz)
12412 82447
22417 92452
32422 10 2457
42427 11 2462
52432 12 2467
62437 13 2472
7 2442 14 (Japan only) 2484
Safety
Product complies with:
●EN60950–1 (2001)
Wireless telecommunications
This product complies with:
●EN 300 328
●EN 301 489–17
●FCC 15.247
42 Appendix C Specifications ENWW
D Regulatory statements
●FCC statement
●Regulatory Model Identification Number
●Canada
●VCCI (Japan)
●RRL statement (Korea)
●Regulatory wireless statements
FCC statement
The United States Federal Communications Commission (in 47 CFR 15.105) has specified that the
following notice be brought to the attention of users of this product.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient the receiving antenna.
2. Increase the separation between the equipment and the receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio/TV technician for help.
For further information, contact:
Manager of Corporate Product Regulations, Hewlett-Packard Company, 3000 Hanover Street, Palo
Alto, California 94304, (650) 857-1501
Modifications (part 15.21)
The FCC requires the user to be notified that any changes or modifications made to this device that are
not expressly approved by HP may void the user's authority to operate the equipment.
ENWW FCC statement 43
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Regulatory Model Identification Number
For regulatory identification purposes, this product is assigned a Regulatory Model Number. The
Regulatory Model Number for your product is RSVLD-0802. The regulatory number should not be
confused with the HP marketing model number (for example, HP Jetdirect ew2500) or the HP product
number (J8021A).
Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
VCCI (Japan)
Class B
RRL statement (Korea)
Class B
44 Appendix D Regulatory statements ENWW
Regulatory wireless statements
●Exposure to radio frequency radiation
●Notice to users in Argentina
●Notice to users in Brazil
●Notice to users in Canada
●European Union regulatory notice
●Notice to users in Indonesia
●Notice to users in Korea
●Notice to users in Mexico
●Notice to users in Pakistan
●Notice to users in Singapore
●Notice to users in South Africa
●Notice to users in Taiwan
Exposure to radio frequency radiation
CAUTION: The radiated output power of this device is far below the FCC radio frequency exposure limits. Nevertheless, the
device shall be used in such a manner that the potential for human contact during normal operation is minimized. This product
and any attached external antenna, if supported, shall be placed in such a manner to minimize the potential for human contact
during normal operation. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity
to the antenna shall not be less than 20 cm (8 inches) during normal operation.
Notice to users in Argentina
CNC:C–5478
Notice to users in Brazil
Aviso aos usuários no Brasil Este equipamento opera em caráter secundário, isto é, não tem direito
à proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar
interferência a sistemas operando em caráter primário.
ENWW Regulatory wireless statements 45
Notice to users in Canada
Notice to users in Canada/Note à l'attention des utilisateurs canadiens
For Indoor Use. This digital apparatus does not exceed the Class B limits for radio noise emissions
from the digital apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications. The internal wireless radio complies with RSS 210 and RSS GEN of Industry Canada.
Utiliser à l'intérieur. Le présent appareil numérique n'émet pas de bruit radioélectrique dépassant les
limites applicables aux appareils numériques de la classe B prescrites dans le Règlement sur le
brouillage radioélectrique édicté par le ministère des Communications du Canada. Le composant RF
interne est conforme a la norme RSS-210 and RSS GEN d'Industrie Canada.
European Union regulatory notice
This product complies with the following EU Directives:
●Low Voltage Directive 2006/95/EC
●EMC Directive 2004/108/EC
Note: CE compliance of this product is valid only if powered with the correct CE-marked AC adapter
provided by HP.
If this product has telecommunications functionality, it also complies with the essential requirements of:
●R&TTE Directive 1999/5/EC
Compliance with these directives implies conformity to harmonized European standards (European
Norms) that are listed in the EU Declaration of Conformity issued by Hewlett-Packard for this product
or product family. This compliance is indicated by the following conformity marking placed on the
product.
The telecommunications functionality of this product may be used in the following EU and EFTA
countries/regions:
Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden,
Switzerland, and United Kingdom.
Notice for France for use of 2.4 GHz wireless communication:
L'utilisation de cet equipement (2.4GHz Wireless LAN) est soumise a certaines restrictions: Cet
equipement peut être utilise a l'interieur d'un bâtiment en utilisant toutes les fréquences de 2400 a
2483.5MHz (Chaine 1-13). Pour une utilisation en environnement extérieur, vous devez utiliser les
fréquences comprises entre 2400-2454 MHz (Chaine 1-9). Pour les dernieres restrictions, voir
www.arcep.fr
For 2.4 GHz Wireless LAN operation of this product certain restrictions apply: This product may be used
indoor for the entire 2400-2483.5 MHz frequency band (channels 1-13). For outdoor use, only 2400-2454
MHz frequency band (channels 1-9) may be used. For the latest requirements, see www.arcep.fr
Contact for European regulatory topics:
46 Appendix D Regulatory statements ENWW
Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, D-71034 Böblingen, Germany
Notice to users in Indonesia
Notice to users in Korea
Notice to users in Mexico
No. de homologacion: SCT RCPHPRS07–310
Notice to users in Pakistan
Notice to users in Singapore
Notice to users in South Africa
ENWW Regulatory wireless statements 47
Notice to users in Taiwan
48 Appendix D Regulatory statements ENWW
© 2014 Hewlett-Packard Development Company, L.P.
www.hp.com

Navigation menu