Hp Photosmart 2575 All In One Printer Setup Guide USSherpaHi

setup guide c00485413

HP PHOTOSMART 2570 c00485413

2015-01-05

: Hp Hp-Photosmart-2575-All-In-One-Printer-Setup-Guide-140653 hp-photosmart-2575-all-in-one-printer-setup-guide-140653 hp pdf

Open the PDF directly: View PDF PDF.
Page Count: 12

2
1
3
HP Photosmart 2600/2700 series all-in-one
User Guide
HP Photosmart 2600/2700 series all-in-one
User Guide
Start Here
HP Photosmart 2570 All-in-One series Setup Guide
Lift the access door and
remove tape on the left
side of the device.
Additional network
equipment specifi ed later
in guide.
4 x 6 in
(10x15 cm)
photo paper
* Purchased separately.
The contents of your box
may differ.
Windows CD
Macintosh CD User Guide
print cartridges
power cord and
adapter
Ethernet cable*USB cable*
USB cable users: Do not connect the USB cable until this
guide instructs you to or the software may not install
properly.
Use this guide to set up the hardware and connect the HP All-in-One to either your computer or a working
network. If you have problems during setup, see Troubleshooting later in the guide.
Remove all tape
Locate components
2 • HP All-in-One
4
The control panel faceplate must be attached for the HP All-in-One to work!
5
6
For best viewing, remove the protective
fi lm from the display.
Lift color graphics display
Load plain white paper
a b c d
Verify the control panel is attached
HP All-in-One • 3
7
8
9
10
USB Cable Users: Do not connect the USB
cable until instructed later in this guide.
a After you press the On button, the green light fl ashes, and
then becomes solid. This may take up to a minute.
b Wait for the print cartridge prompt before continuing.
On
Open the access door
Remove tape from both cartridges
Pull the pink tab to remove the tape from both print cartridges.
Do not touch the copper-colored contacts or retape the
cartridges.
Lift the access door until it stops. The print
carriage moves to the right.
Press the On button and confi gure
Connect the power cord
4 • HP All-in-One
11
12
Insert the tri-color print cartridge
a Hold the tri-color print cartridge with the HP label facing
up.
b Place the tri-color print cartridge in front of the left slot
marked with the green label.
c Push the cartridge fi rmly into the slot until it snaps into
place.
a Hold the black print cartridge with the HP label facing up.
b Place the black print cartridge in front of the right slot
marked with the black and orange label.
c Push the cartridge fi rmly into the slot until it snaps into
place.
d Close the access door.
The device must be On before you can insert the print
cartridges.
When the device is on, the print carriage is on the right
side.
Insert the black print cartridge
HP All-in-One • 5
13
14
Align the print cartridges
a Press OK at each of the prompts on the control panel to
start print cartridge alignment.
The alignment may take a few minutes.
b After the page prints, alignment is complete. Check the
color graphics display for the status, and then press OK .
If it fails, try again with plain white paper. See the User
Guide for more information.
Recycle or discard the alignment page.
Turn on your computer
a Turn on your computer, login if necessary, and then wait
for the desktop to appear.
b Close any open programs.
6 • HP All-in-One
15
A: USB Connection - Do not connect yet.
B: Ethernet (Wired) Network
Use this connection type if you want to connect the
device directly to one computer. (Do not connect until
the software instructs you to.)
Equipment needed: USB cable.
For a USB connection, go to Section A (page 7) for
instructions.
Use this connection type if you want an Ethernet
cable connection between the device and your
network.
Equipment needed: hub/router/switch and Ethernet
cable.
For an Ethernet cable connection, go to Section B
(page 9) for instructions.
Questions: For information on how to set up a
network, go to www.hp.com/support , enter
Photosmart 2570 , and search for Network Setup .
Choose ONE connection type (A or B)
A1
HP All-in-One • 7
Windows Users: Macintosh Users:
a Insert the HP All-in-One Windows CD.
b Follow the onscreen instructions to install the
software.
c On the Connection Type screen, make sure to
select directly to this computer . Continue to the
next page.
a Locate the HP All-in-One Macintosh CD.
b Continue to the next page.
Note: If the startup
screen does not
appear, double-click
My Computer , double-
click the CD-ROM icon,
and then double-click
setup.exe .
Choose the correct CD
Section A: USB Connection
A2
A3
8 • HP All-in-One
b Follow the onscreen instructions. Complete the
Sign up now screen.
b Double-click the HP All-in-One installer icon.
c Make sure you complete all screens, including the
Setup Assistant.
Macintosh Users:Windows Users:
a Connect the USB cable from your computer to the
USB port on the back of the device.
a Follow the onscreen instructions until you see
the prompt to connect the USB cable. (This
may take several minutes.)
Once the prompt appears, connect the USB
cable to the port on the back of the
HP All-in-One, and then to any USB port on
your computer.
Go to the last page to make a test copy
Connect the USB cable
B1
HP All-in-One • 9
a Remove the yellow plug from the back of the device.
b Connect one end of the Ethernet cable to the Ethernet
port on the back of the device.
c Connect the other end of the Ethernet cable to the hub/
router/switch. If the cable is not long enough, you can
purchase a longer cable.
Important: Do not connect the Ethernet cable to a
cable modem.
You must have a working network. If you already
connected the USB cable, do not connect the Ethernet
cable.
Section B: Ethernet (wired) network
Connect the Ethernet cable
a
c
b
10 • HP All-in-One
B2 Insert the correct CD
Windows Users: Macintosh Users:
a Insert the HP All-in-One Macintosh CD.
b Double-click the HP All-in-One installer icon.
c Make sure you complete all screens,
including the Setup Assistant. Continue to
the next page.
a Insert the HP All-in-One Windows CD.
b Follow the onscreen instructions to install the
software.
c On the Connection Type screen, make sure to
select through the network . Follow the onscreen
instructions.
d You must choose unblock or accept on all fi rewall
messages or setup will fail. Follow all onscreen
instructions. Continue to the next page.
Note: If the startup screen
does not appear, double-
click My Computer , double-
click the CD-ROM icon, and
then double-click setup.exe .
Questions : Anti-virus, Anti-Spyware, or fi rewall
programs can block software installation.
For details, go to www.hp.com/support , enter
Photosmart 2570 , and then search for Firewalls .
HP All-in-One • 11
B3
B4
Install software on additional computers
If you have additional computers on your network, install the
HP All-in-One software on each computer. Choose the correct
HP All-in-One CD for each installation.
Follow the onscreen instructions. Make sure that you choose the
connection type between the network and your HP All-in-One (not
between your computer and the network).
Go to the last page to make a test copy
Problem: You did not see the screen prompting you to connect the USB cable.
Action: Remove, and then re-insert the HP All-in-One Windows CD. Refer to Section
A.
Problem: The Microsoft Add Hardware screen appears.
Action: Click Cancel . Unplug the USB cable, and then insert the HP All-in-One
Windows CD. Refer to Section A.
Problem: The Device Setup Has Failed To Complete screen appears.
Action: Verify that the control panel faceplate is fi rmly attached. Unplug the
HP All-in-One and plug it in again. Check all connections. Make sure the USB cable
is plugged into the computer. Do not plug the USB cable into a keyboard or non-
powered hub. Refer to Section A.
Problem: A Carriage Jam message appears.
Action: Open the access door. Remove the tape from inside the device. Turn the
power off, and then wait one minute. Turn the power on again.
Troubleshooting
*Q7211-90257*
Q7211-90257
*Q7211-90257*
To learn about printing photos from memory cards and
other features, see the User Guide and online help. For
additional help, see www.hp.com/support .
b Find a 4x6 in (10x15 cm) photo.
c Place the photo (face down) on the right front corner
of the glass. Make sure the long edge of the photo is
along the front of the glass. Close the lid.
d Press the Start Copy Color button.
The HP All-in-One makes a copy of your original photo.
Now that you have fi nished setup, it is time to use your HP All-in-One. Make a copy of a favorite photo.
a
c
a Remove the plain white paper and load the 4 x 6
in (10x15 cm) photo paper. Place the paper glossy
side down. Move the paper adjusters next to the
stack of paper.
b
d
Make a test copy
© Copyright 2005 Hewlett-Packard Development Company, L.P. Printed in [].
Printed on at least 50% total recycled fi ber with at least 10% post-consumer paper.

Navigation menu