Hp Printer Hp2300 Users Manual

2015-02-09

• Chapter 1: Product Information
  • 1-1: Introduction
  • 1-2: Produc Descriptions
  • 1-3: Identification
  • 1-4: Options
  • 1-5: Available Supplies
  • 1-6: Related Manuals
  • 1-7: Specifications
  • 1-8: Safety Compliance
  • 1-9: FCC RFI Statement
  • 1-10: Service Approach
• Chapter 2: Installation & Configuration
  • 2-1: Introduction
  • 2-2: Site Requirements
  • 2-3: Unpacking & Installation
  • 2-4: Self Test
  • 2-5: Printer Configuration
  • 2-6: I/O Configuration
  • 2-7: HP-IB Configuration
  • 2-8: Compatibility Configuration Mode
• Chapter 3: Theory of Operation
  • 3-1: Introduction
  • 3-2: Functional Operation
  • 3-3: Formatter PCA
  • 3-4: Processor/Control Circuitry
  • 3-5: Dot Generation Logic
  • 3-6: Analog/Backplane PCA
  • 3-7: I/O Ports (Analog PCA)
  • 3-8: Stepper Motor Circuitry
  • 3-9: Printbar Motor Circuitry
  • 3-10: Position Encoder Circuit
  • 3-11: Hammer Driver PCA
  • 3-12: Control Panel PCA
  • 3-13: Sensors (Connected to Analog PCA)
  • 3-14: Power Supply (Analog PCA)
• Chapter 4: Configuration & Diagnostics
  • 4-1: Introduction
  • 4-2: Printer Configuration & Status Info
  • 4-3: Operational Status Codes
  • 4-4: Self Test & Selectable Subtests
  • 4-5: CE Mode Operation
  • 4-6: Errors
  • 4-7: Printer Error Log
  • 4-8: Interface Configuration
  • 4-9: Locking the Control Panel
• Chapter 5: Adjustments
  • 5-1: Introduction
  • 5-2: Required Tools
  • 5-3: Sequence of Adjustments
  • 5-4: Crank Arm Phase Adjustment
  • 5-5: Velocity Transducer Adjustments
  • 5-6: Platen Gap Adjustment
  • 5-7: Timing Adjustments
  • 5-8: Flight Time
  • 5-9: Turnaround Time
  • 5-10: Cold Start
• Chapter 6: Removal & Replacement
  • 6-1: Introduction
  • 6-2: Required Tools
  • 6-3: Top Cover
  • 6-4: Control Panel
  • 6-5: Formatter, Graphics & Interface PCA
  • 6-6: Upper Fan
  • 6-7: Analog PCA
  • 6-8: Hammer Driver PCA
  • 6-9: Capacitor PCA
  • 6-10: Ribbon Motor
  • 6-11: Stepper Motor
  • 6-12: Paper Feed Tractors
  • 6-13: Cross-flow Fan
  • 6-14: Printer Weldment
  • 6-15: Velocity Transducer
  • 6-16: Platen
  • 6-17: Stabilizer Blocks
  • 6-18: Printbar
  • 6-19: Ribbon Shield
  • 6-20: Print Mechanism
  • 6-21: Printbar Drive Motor
  • 6-22: Sensor Switches
  • 6-23: Lower Fan
  • 6-24: Transformer
• Chapter 7: Parts & Diagrams
  • 7-1: Introduction
  • 7-2: Using this Chapter
  • 7-3: Parts Ordering Procedure
  • 7-4: Diagrams and Parts Lists
• Appendix A: Diagnostic Errors
• Appendix B: Print Quality
• Appendix C: Test Points
• Appendix D: Anzac Support
• Appendix E: Paper Specifications