Hp Storefabric Sn1000Q 16Gb 1 Port Pcie Fibre Channel Host Bus Adapter Users Guide Onecommand
Hp-Sn1000E-16Gb-1-Port-Pcie-Fibre-Channel-Host-Bus-Adapter-Users-Guide-670227 hp-sn1000e-16gb-1-port-pcie-fibre-channel-host-bus-adapter-users-guide-670227
2015-03-28
: Hp Hp-Storefabric-Sn1000Q-16Gb-1-Port-Pcie-Fibre-Channel-Host-Bus-Adapter-Users-Guide-670510 hp-storefabric-sn1000q-16gb-1-port-pcie-fibre-channel-host-bus-adapter-users-guide-670510 hp pdf
Open the PDF directly: View PDF
Page Count: 278 [warning: Documents this large are best viewed by clicking the View PDF Link!]
- Introduction
- Installing and Uninstalling OneCommand Manager Application Components
- Installing the OneCommand Manager Application
- Installing the OneCommand Manager Application Web Launch Interface
- Installing the OneCommand Manager Application Command Line Interface
- Upgrading from the OneCommand Manager Application CLI to the Full- Featured OneCommand Manager Application Enterprise Kit
- Uninstalling the OneCommand Manager Application
- Uninstalling the OneCommand Manager Application Web Launch Interface Only
- Starting and Stopping the OneCommand Manager Application
- Using the OneCommand Manager Application
- Configuring Discovery
- Viewing Discovery Information
- Viewing Host Grouping Information
- Viewing Host Information
- Grouping Hosts
- Searching for Hosts
- Viewing Adapter Information
- Viewing ASIC Information
- Viewing Port Information
- Viewing Physical Port Information (OneConnect Adapters Only)
- Viewing Port Statistics
- Viewing FC Virtual Port Information (FC and FCoE Adapters Only)
- Viewing FC Fabric Information (FC and FCoE Adapters Only)
- Viewing Transceiver Information
- Viewing PHY Data (OneConnect OCe11100 series Adapters Only)
- Viewing Vital Product Data (VPD)
- Viewing Maintenance/Firmware Information
- Viewing Target Information
- Viewing LUN Information
- Viewing FC/FCoE Target Mapping (Windows and Solaris)
- Viewing Target Mapping (Linux and VMware ESX)
- Viewing iSCSI and NIC PCI Registers
- Managing Adapters
- Managing Devices using CIM
- Showing and Installing Licenses for OneConnect Adapters
- Changing Personalities on OneConnect Adapters
- Configuring the FC/FCoE Adapter Driver
- The Host Driver Parameters Tab
- Setting Driver Parameters
- Setting Driver Parameters for a Single Adapter
- Restoring All Parameters to Their Earlier Values
- Resetting All Default Values
- Setting an Adapter Parameter Value to the Host Adapter Parameter Value
- Saving Adapter Driver Parameters to a File
- Setting Driver Parameters for All Adapters in a Host
- Changing Non-dynamic Parameter Values (Linux 8.2)
- Changing Non-dynamic Parameter Values (VMware ESX)
- Creating a Batch Mode Driver Parameters File
- Configuring DCB (Data Center Bridging) Parameters
- Configuring FCoE Initialization Protocol (FIP) for FCoE Adapters
- Managing Ports
- Changing Adapter Port Names (FC Ports Only)
- Resetting Adapter Ports (FC/FCoE Ports Only)
- Modifying TCP/IP iSCSI Port Configuration
- Enabling and Disabling FC Ports
- Enabling and Disabling Physical Ports (OneConnect Adapters Only)
- Setting Port Speed and DAC Cable Length (OneConnect OCe11102 Series Adapters Only)
- Configuring iSCSI Port Initiator Login Options
- Changing World Wide Name Configuration (FC/FCoE Ports Only)
- Creating and Deleting FC Virtual Ports (FC and FCoE Ports Only)
- Using FC-SP DHCHAP Authentication (Windows, Linux 8.2 and Solaris)
- Updating Adapter Firmware
- Mapping and Masking (FC and FCoE Ports Only)
- Configuring Boot from SAN
- Exporting SAN Information
- Diagnostics
- LightPulse FC HBA Diagnostics
- Viewing Flash Contents, PCI Registers and Wakeup Information
- Viewing Flash Contents
- Viewing Overlay Details
- Viewing the PCI Registers
- Running a Quick Test
- Running a Power On Self Test (POST)
- Using Beaconing
- Creating Diagnostic Dumps
- Running Advanced Diagnostic Tests
- Running Loopback Tests
- Loopback Test Combinations
- Running End-to-End (ECHO) Tests
- Saving the Log File
- OneConnect Diagnostics
- LightPulse FC HBA Diagnostics
- Using the OneCommand Manager Application Command Line Interface
- The CLI Client Command Reference
- Using the CLI Client
- The Command Reference
- Help Command
- Adapter License Management Commands
- Attributes Commands
- Authentication Commands
- Boot Commands
- CEE Commands
- Data Center Bridging Commands
- Diagnostic Commands
- Driver Parameter Commands
- Dump Commands
- FCoE Commands
- iSCSI Commands
- AddARPTableEntry
- AddRouteTableEntry
- AddTarget
- AddTargetPortal
- CleariSNSServer
- DelARPTableEntry
- DelRouteTableEntry
- DiscoveriSNSServer
- GetInitiatorProperties
- GetiSCSILuns
- GetiSCSIPortStats
- GetSessionInfo
- iSCSIPing
- ListSessions
- RemoveTarget
- RemoveTargetPortal
- SetInitiatorProperties
- SetNetworkConfiguration
- SetTargetLoginProperties
- SetTargetProperties
- SetTPLoginProperties
- ShowARPTable
- ShowiSNSServer
- ShowRouteTable
- ShowTarget
- ShowTargetPortal
- TargetLogin
- TargetLogout
- UpdateiSNSServer
- LUN Masking Commands
- Miscellaneous Commands
- Persistent Binding Commands
- Personality Change Commands
- Virtual Port (VPort) Commands
- WWN Management Commands
- Troubleshooting