Hua Xin Information Technology 20180720300 Robotic Vacuum Cleaner User Manual
Shenzhen Hua Xin Information Technology Co., Ltd Robotic Vacuum Cleaner
User manual
HX-V302
Instructions for use
Technology makes life better
Robotic Vacuum Cleaner
HX-V302
Instructions for use
FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
*RF warning for Mobile device:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
Thank you for purchasing the smart cleaning
Robot!
We hope that our product will bring you a smarter
and more convenient lifestyle!
1. Welcome 2. Safety Instruction 3. Product Components
The image above is for illustration purposes only; the actual product may differ.
Our company reserves the right to upgrade products without notice.
4. Instructions for Use 5. Product Maintenance 6. Common faults
6.2 Replaceable Modules
Dust box
Shell
Fan Components
Side Brush Components
Right Side Wheel Component
Left Side Wheel Component
Right Side Brush
Left Side Brush
Universal Wheel
Bottom Shell
Lithium Battery
Battery Cover
Scraper
Pressing Plate
1. Welcome 2. Safety Instruction 3. Product Components
4. Instructions for Use 5. Product Maintenance 6. Common faults
1. Welcome 2. Safety Instruction 3. Product Components 4. Instructions for Use 5. Product Maintenance 6. Common faults
6.1 Alarm Warning Contents
1.Welcome
2.Safety Instructions
3.Product Components
3.2 Product Specifications
3.1 Names of Parts
3.3 Product Characteristics
4.Insructions for use
4.1 Remote Control Instructions
4.2 Operating Instructions
5.Product Maintenance
5.1 Side Brush Cleaning and Replacement
5.2 Cleaning of Dust Box and Filter
5.3 Maintenance of Rolling Brush Components
5.4 Replaceable Modules
6.Common Faults
6.1 Alarm and Warning
6.2 Replicable Moduels
1. Welcome 2. Safety Instruction 3. Product Components 4. Instructions for Use 5. Product Maintenance 6. Common faults
Safety Considerations of Main Body and Accessories
Before using this product, please read the safety instructions
below and follow all the routine safety precautions.
A. Warning
01.Do not disassemble,repair or refit the product without authorization;otherwise it may damage the
product or pose a hazard.
02.Do not use the product in an environment with risk of fire or explosion.
03.This product can only use the original power adapter;otherwise the product may be damaged or
catch on fire.
04.Do not stand or sit on this product; doing so could damage the product or cause it to fall over.
05.When the metal part of the power plug is dusty, please wipe it with a dry cloth.
06.The power adapter is applied to a 100-240V AC voltage. Please plug into the socket properly and
keep away from children.
07.Do not wash or soak the main body and electronic accessories in water; otherwise the product may
be damaged by a short circuit.
08.Do not damage, load weight on, heat, pull, or bend it.
09.During cleaning, please pay attention to the safety of toddlers and elders at home to avoid
tripping, and please do not touch the wheel and side brush to avoid injury. (Please pay special
attention to toddlers).
10.This product is for home use. Please do not use it outdoors.
11.Do not allow metal and conductive materials to come in contact with the battery; doing so may
cause a short circuit.
12.Do not use without dust bin and/or filters in place.
13.Do not operate the Appliance in an area where there are lit candles or fragile objects.
14.Do not use Appliance on wet surfaces or surfaces with standing water.
15.Do not use Appliance to pick up anything that is burning or smoking, such as cigarettes, matches,
hot ashes, or anything that could cause a fire
Please read the Instructions carefully and keep them for future reference. Any operation that
does not conform to the Instructios may cause damage to the product.
B Attention
01.Do not touch the product with wet hands; doing so may cause an electric shock.
02.Please do not place the product in places where it could easily fall, such as tables, chairs, high
platforms in room, etc.
03.The product has a sophisticated design and should be protected from long-term exposure to
sunlight.
04.Please do not use the product in humid environments, such as bath-rooms.
05.Please do not place the product near cigarette butts,lighters or other open fires.
06.Please clean the product after the end of charging.
07.Please turn off the power switch on the side of the robot when the product is out of service for a
long time.
08.Please check carefully to see if the power adapter is connected to the socket prior to use, to avoid
damage to the robot.
09.Before using the product,please remove all vulnerable items on the floor,such as glass,lamps,and
items such as wires and curtains that may entangle with the side brush and suction passages.
Charge Tetminal
Use the cleaning tools or a dry soft cloth to periodically clean the
charging plate of robot chassis and the sensor window.
1. Welcome 2. Safety Instruction 3. Product Components 4. Instructions for Use 5. Product Maintenance 6. Common faults
5.3 Maintenance of Rolling Brush Components
Open the rolling brush components. Remove the rolling brush and dry it flat.
Please do not use the brush that is still dripping in case of slipping.
This component can be applied to wooden floors, tile floors, marble floors, painted hard floors
and so on.
5.4 Maintenance of Other Components
Electrode slice
Sensor
Use cleaning tools or a dry soft cloth to periodically clean the charging
plate of robot chassis and the sensor window.
10. This product may not cross a vertical step of approximately 8 mm high.
11.When the dust box is full, please empty the garbage before using again.
12.Please do not use the robot to clean construction waste.
13.The operating temperature of the product ranges from 0 degrees Celsius to 40 degrees Celsius;
please do not use it in a high temperature environment.
14.Before the product is scrapped, please remove the battery from the robot.When you remove
the battery, please ensure that the product is not connected to a power supply. Please recycle
the battery safely for environmental protection.
Safety Considerations for Rechargeable Battery
Danger
01.Always use a dedicated battery adapter to avoid leakage, heating or rupture.
02.Do not short-circuit the battery or remove the battery; doing so may cause leakage, heating or
rupture.
03.Do not transport or preserve with necklaces, hairpins and other metal objects; doing so may lead
to short circuit, resulting in leakage, heating or rupture.
04.Do not burn or heat the battery; doing so may cause leakage, heating or rupture.
Attention
01.If abnormal overheating is discovered during charging, stop using it immediately to avoid
leakage, heating or rupture.
02.To prolong the service life of the battery, please remove the battery and place it in a cool,
dry environment if it is out of service for a long time; this will avoid leakage, heating or
rupture.
03.Do not soak it in water or let it come into contact with any liquid; otherwise it may cause
leakage, heating or rupture.
04.Be sure to stop using it immediately in case of any exception (e.g. discoloration or
deformation), to avoid leakage, heating or rupture.
05.Always use tape to insulate the battery’s electrode when recycling or disposing of it.
06.Contact with other metals will cause heat to crack or catch fire. Please bring used batteries
to recyclers or dispose of them according to local regulations.
A Warning
01.When skin or clothing is exposed to the battery electrolyte, immediately wash with clean water
to avoid inflammation of skin, etc.
02.Do not use the rechargeable battery on other devices. This battery is only suitable for Cisno
Robotic Vacuum Cleaners.
03.If the battery’s outer box is found to be deformed and expanded,or leakage of electrolytes is
found,do not charge or continue to use to avoid danger.
04.Do not throw or inflict a strong impact on the battery;doing so may cause
leakage,heating or rupture.
05.Do not disassemble the battery pack;doing so may cause battery rupture and electrolyte
outflow,leading to fire,explosion and other dangers.
1. Welcome 2. Safety Instruction 3. Product Components 4. Instructions for Use 5. Product Maintenance 6. Common faults
3.1 Names of components
Main Body Charging base 2 AAA batteries
Remote control Ac adapter Cleaning tools
Cistern components Side brushes High-effective filter
While the accessories provided for some models are slightly different, they
are subject to the actual product.
次
Dry all parts until they are completely dry
Replace the primary filter and high-efficiency filter back into the trash box
1. Welcome 2. Safety Instruction 3. Product Components 4. Instructions for Use 5. Product Maintenance 6. Common faults
Lower the height of the dust box and dump the trash
Clean the dust box, high efficiency filter and primary filter thoroughly.
After the pre-filter is used for 15-30 days, it should be washed once.
Main Body
1.Bumper 2.control keys 3.panel 4.Middle cover
Main Body
1. Universal wheel 2. Charging shrapnel 3. Side brush 4. Battery cover
5. Suction port 6. Base plate 7. Cincture 8.Freezer/ cleaning cloth
1. Welcome 2. Safety Instruction 3. Product Components 4. Instructions for Use 5. Product Maintenance 6. Common faults
Main Body
1.Middle cover 2.Dust box 3.DC power jack 4.Power switch
Dust Box
1. Dust box cover 2. Pre-filter 3. Dust box 4. High-effective filter 5. Dust box sealer
remove the high-efficient filter
Open the dust box cover and remove the pre-filter
1. Welcome 2. Safety Instruction 3. Product Components 4. Instructions for Use 5. Product Maintenance 6. Common faults
5.1 Side brush cleaning and replacement
Check the side brush at variable intervals to see if it has been damaged or wrapped with
something. Clean the side brush with a cleaning tool or a rag. When the side brush doesn’t
work, replace it in time. L and R correspond to each other.
5.2 Dust box and filter cleaning
Lift the top cover and remove the dust box. Please check the suction channel and clean it up.
Charging Base
1. Charging indicator 2. DC power jack 3.Charging terminal
1. Welcome 2. Safety Instruction 3. Product Components 4. Instructions for Use 5. Product Maintenance 6. Common faults
1.Rolling brush 2. Poron 3. Water inlet 4. Water box sealer
Water Tank Attachment
Plan Cleaning
The robot will perform the smart Plan
Cleaning according to the room
environment.
Edge Cleaning
The robot will clean
along the longest edge
of the room
Fixed point cleaning
This function is only applicable to the operation
on the APP
Cleaning Mode
1. Welcome 2. Safety Instruction 3. Product Components 4. Instructions for Use 5. Product Maintenance 6. Common faults
Water box use-instrucions
Please remove the tank when charging to avoid danger
Water tank assembly
There is a corresponding affixing place at the bottom of the water tank. Fix the bibulous rag
according to the corresponding position on the bottom of the tank, open the tank sealing cover,
and fill it with clear water to the position between its 1/2 and 2/3, and then cover the sealer
well.
Water tank installation
Hang the water tank components on the bottom of the main body according to the direction
shown in the figure, and place the two columns on the water tank in the two holes of the main
body base so that the water tank can be closely linked with the base.
Please remove the tank when charging to avoid danger
3.2Product Specifications
Structure Type
Diameter of main body
Thickness of main body
Net weight of main body
320mm
75mm
2.5 kg
Electronic Type
Voltage
Battery capacity
Main body button type
14.4v
2000mAh
Mechanical keys
Accessory Type
Water box capacity
Dust box capacity
Wipe size
180ml
600ml
316x177 x4mm
Process Parameters
Charging Type
Operating duration
Charging duration
Manual/Automatic
<= 100 min
240 – 300 min
3.3 Product Charasteristics
Strong suction power
The suction power of this product is strong. Even tiny dust will be thoroughly cleaned.
Intelligent suction power regulation
This product automatically adjusts the suction power according to different cleaning modes. This not
only greatly increases the cleaning efficiency, but also saves 30% of power. It can also be adjusted
with the remote control
Humanized Design
It is simple to operate. You can control the robot only by pressing the Control button “start”!
Follow the prompt tone to operate the robot!
Press the button and the voice "enter plan cleaning mode" and the robot will start sweeping, then
press this key to control the machine to pause or continue working, and a voice “beep” can be
heard.
Press and hold the key, after hearing the “beep” sound and remove your finger , and the robot will
say " robot is trying to connect the Internet", and then it can be connected according to the robot
WIFI setting instructions.
The product storage environment temperature range is from 0 to 40 degrees Celsius
4.1Remote Control Instructions
PowerOn/Off
Display Screen
Return for Auto Charging
Direction
Clock Settings
Single room Cleaning
Edge Cleaning
Plan cleaning
Confirm
Suction Settings
Sweeping and Cleaning
Preset
1. Welcome 2. Safety Instruction 3. Product Components 4. Instructions for Use 5. Product Maintenance 6. Common faults
Mode switching
Standby mode.
The power switch is on. the “confirm” key is on. the machine is at rest
Sleeping mode.
The power switch is on, the key is blinking, the machine is at rest.
Operating mode.
The machine is working, the key light is on, the machine will start
sweeping.
Operation peocedure.
sleeping mode-standby mode-operating mode
Startup
01.Make sure the power switch on the side of the robot is turned on.
02.Press the Control button or the Cleaning mode on the remote control to startthe robot.
Pause
This function is to switch the robot from the operating mode to the select and the robot can be paused
by the following operations:
01.Press the Control button on the robot to pause the robot.
02.Press the power on/off button on the remote control to pause the robot.
Sleep
The machine will not work in this mode, the key light is yellow.without any operations, this robot will
sleep in this mode. The machine can come back to work again through pressing the “confirm”button on
the main body or through the remote control.
1. Welcome 2. Safety Instruction 3. Product Components 4. Instructions for Use 5. Product Maintenance 6. Common faults
autocharge
Press the “recharging button” , this machine will automaticly recharge itself.
When the cleaning is completed or the battery is too low, the machine will automatically
start to look for charging base. Keep the charging base powered on, otherwise the
machine will not be able to find the base for charging.
When charging itself, pressing the "Sweeping" button on the remote control will stop the
charge and start cleaning. This operation cannot be performed when using the charging
adapter to charge.
Note:
Notes for charging:
A.the yellow light will be on when the power is low;
B.the green light will blink while charging;
C.the green light will be on when the power is full;
D.check the charging after the machine runs out of electricity;
E. When charging for the first time, make sure the machine is charged for at least 12 hours.
F.If you do not use the machine for a long time, turn off the power switch;
G.If you need to use it everyday, place the machine on the charging base and make sure the
charging base is powered on.
H. When the power is low, it will find its own charger. Please make sure there are no obstacles
around the charger;
It is the button for plan cleaning
no matter what mode the machine is in, this button will bring it to the plan cleaning.
Recharging button
Pressing this button to shift the mode as recharging, and the logo will be shown on the play
screen.
Forward
Forward /At the standby mode, press this button to continue moving forwards, and release it to
return to the standby mode.At the Preset mode or the Time Settings mode, press this button to
increase the number.
Backward
At the standby mode, press this button to continue moving backwards, and release it to return to
the standby mode. At the Preset mode or the Time Settings mode, press this button to decrease
the number.
Left Arrow
At the standby mode, press this button to continue turning left, and release it to return to the
standby mode.At the Preset mode or the Time Settings mode, press this button to switch from
minute to hour.
Right Arrow
At the standby mode, press this button to continue turning right, and release it to return to the
standby mode. At the Preset mode or the Time Settings mode, press this button to switch from
hour to minute.
Confirm button
During operation, press this button to stop the robot, and it is still working at the pause.In the
preset or clock setting modes, this button can save all the settings
Suction Settings button
At any cleaning mode, press this button to adjust the suction power.
Clock Settings button
Press this button to enter the Clock Setting mode and press the OK button to exit.
Single room cleaning button
Press the button to star cleaning a single room
Floor mapping button
Press this button to map the floor
Edge Cleaning button
Press this button to enter the Edge Cleaning mode.
Preset button
At the standby mode, press this button to enter the presetting mode, and the display �ashes
icon.
At the preset mode, press this button to save the data and exit the preset mode, and the display
will always display the icon.
At the preset mode, press the preset button for 3S to cancel the preset function, and the
displayed icon will disappear.
3 buttons mentions above can adjust the suction power.
1. Welcome 2. Safety Instruction 3. Product Components 4. Instructions for Use 5. Product Maintenance 6. Common faults
4.2 Operating Instructions
Placement of the Charging Base
Place the seat flat against the wall. Do not place any objects within 2 meters to the left / right
and 1 meter to the front, and do not place any mirrors or other reflective objects within this
distance.
Switch on the robot, “I”means to turn on, “o”means to trun off which makes the Control
button green, and enter the Select mode.
If the robot is not active within 5 minutes, the robot will enter Sleep mode.
Main body charging
Make sure the power switch is turned on before charging the machine
Charging mode A
Plug the power adapter jack directly into the machine and the other end to the power supply
to charge the machine.
Charging mode B
Place the main body in the charging base to charge the machine, making sure it inserts into
the electrode slices. (The blinking green light indicates that the charging is in progress, and
the charging is completed when it is on.
Make sure the power switch is turned on before charging the machine