Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual

Shanghai Huace Navigation Technology LTD. Geodetic GNSS Receiver E91 User Manual

Contents

User_Manual

CHC® E91 GNSS Receiver User Guide Revision 1.0 June 01, 2018
Table of Content 2 Table of Content Table of Content.................................................................................................... 2 Preface ................................................................................................................. 5 Copyright ................................................................................................................ 5 Safety Warnings ..................................................................................................... 5 FCC Interference Statement ................................................................................... 5 CE Interference Statement ..................................................................................... 6 1 Introduction ................................................................................................... 7 1.1 Safety Information ..................................................................................... 7 1.1.1 Warnings and Cautions ...................................................................... 7 1.1.2 Regulations and Safety ....................................................................... 7 1.1.3 Use and Care ...................................................................................... 8 1.2 Technical Support ....................................................................................... 8 1.3 Disclaimer ................................................................................................... 8 1.4 Your Comments .......................................................................................... 8 2 Getting Started with E91 ................................................................................. 9 2.1 About the Receiver .................................................................................... 9 2.2 Parts of the Receiver .................................................................................. 9 2.2.1 Front Panel ......................................................................................... 9 2.2.2 Receiver Ports .................................................................................. 11 2.3 Batteries and Power ................................................................................. 12 2.3.1 Internal Batteries ............................................................................. 12 2.3.2 External Power Supply ..................................................................... 13 2.4 Product Basic Supply Accessories ............................................................ 14 2.4.1 Base Kit Basic Supply ........................................................................ 14 2.4.2 Rover Kit Basic Supply ...................................................................... 15 2.5 Connecting to an Office Computer .......................................................... 16 2.6 Connecting to a Controller ....................................................................... 17 2.6.1 Connecting via Wi-Fi with LandStar 7 Software ............................... 17 2.6.2 Connecting via Bluetooth with LandStar 7 Software ....................... 18 2.7 Downloading Logged Data ....................................................................... 20 3 Base Station Setup and Operation .................................................................. 22 3.1 Base Station Setup Guidelines ................................................................. 22 3.2 Outputting Corrections Using Internal Radio Modem ............................. 23 3.2.1 Base Station Setup ........................................................................... 23 3.3 Outputting Corrections Using External Radio .......................................... 23 4 Rover Station Setup And Operation ................................................................ 25 4.1 Rover Station Setup Guidelines................................................................ 25 4.2 Rover Station Setup .................................................................................. 26
Table of Content 3 5 Configuring Through a Web Browser .............................................................. 27 5.1 Status Menu ............................................................................................. 28 5.1.1 Position Submenu ............................................................................ 29 5.1.2 Activity Submenu ............................................................................. 29 5.1.3 Google Map Submenu ..................................................................... 30 5.2 Satellites Menu ........................................................................................ 31 5.2.1 Tracking Table Submenu .................................................................. 31 5.2.2 Tracking Info. Table Submenu .......................................................... 32 5.2.3 Tracking Skyplot Submenu ............................................................... 32 5.2.4 Satellite Activation Submenu ........................................................... 32 5.2.5 Tracking Enable Submenu ................................................................ 33 5.3 Receiver Configuration Menu .................................................................. 34 5.3.1 Description ....................................................................................... 34 5.3.2 Antenna Configuration Submenu .................................................... 34 5.3.3 Reference Station Settings Submenu ............................................... 35 5.3.4 Receiver Reset Submenu ................................................................. 38 5.3.5 Languages Submenu ........................................................................ 38 5.3.6 User Management Submenu ........................................................... 38 5.3.7 USB Function Switch Submenu ........................................................ 39 5.3.8 HCPPP Settings Submenu................................................................. 39 5.4 Data Recording Menu .............................................................................. 39 5.4.1 Log Settings Submenu ...................................................................... 39 5.4.2 FTP Push Settings Submenu ............................................................. 41 5.4.3 FTP Push Log Submenu .................................................................... 42 5.4.4 Data Download Submenu ................................................................ 42 5.5 IO Settings Menu ...................................................................................... 44 5.5.1 IO Settings Submenu ........................................................................ 44 5.6 Network Setting Menu ............................................................................. 51 5.6.1 Description Submenu ....................................................................... 51 5.6.2 Mobile Network Setting Submenu................................................... 52 5.6.3 Email Alarm Submenu ...................................................................... 53 5.6.4 HTTP Submenu ................................................................................. 54 5.6.5 HTTPS Submenu ............................................................................... 55 5.6.6 FTP Service Submenu ....................................................................... 55 5.7 Module Setting Menu .............................................................................. 55 5.7.1 Description Submenu ....................................................................... 56 5.7.2 WiFi Submenu .................................................................................. 56 5.7.3 Bluetooth Settings Submenu ........................................................... 57 5.7.4 Radio Settings Submenu .................................................................. 57 5.8 Firmware Menu ........................................................................................ 58 5.8.1 Firmware Info Submenu ................................................................... 59 5.8.2 Hardware Version Submenu ............................................................ 59
4 5.8.3 Config File Submenu ........................................................................ 59 5.8.4 System Log Download Submenu ...................................................... 60 5.8.5 User Log Submenu ........................................................................... 60 5.8.6 Firmware Update Submenu ............................................................. 60 5.8.7 GNSS Board Upgrade Submenu ....................................................... 61 5.8.8 Radio Upgrade Submenu ................................................................. 61 5.8.9 Upgrade Online Submenu ................................................................ 61 5.8.10 GNSS Registration Submenu ........................................................ 62 5.9 Cloud Service Setting Menu ..................................................................... 62 5.9.1 Cloud Service Setting Submenu ....................................................... 62 A Communication Ports Definition ....................................................................... 64 AI CHC E91 Receiver IO Port (7-pin Lemo Port) Definition .................................. 64
Preface 5 Preface Copyright Copyright 2016-2017 CHC | Shanghai Huace Navigation Technology Ltd. All rights reserved. The CHC are trademark of Shanghai Huace Navigation Technology Limited. All other trademarks are the property of their respective owners. Trademarks All product and brand names mentioned in this publication are trademarks of their respective holders. Safety Warnings The Global Positioning System (GPS) is operated by the U.S. Government, which is solely responsible for the accuracy and maintenance of the GPS network. Accuracy can also be affected by poor satellite geometry and obstructions, like buildings and heavy canopy. FCC Interference Statement This equipment has been designed to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules in the Portable Mode. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
Preface 6 CE Interference Statement Declaration of Conformity: Hereby, Shanghai Huace Navigation Technology Ltd. declares that this E91 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. A copy of the Declaration of conformity can be found at Shanghai Huace Navigation Technology Ltd.
Introduction 7 1 Introduction The E91 GNSS Receiver User Guide describes how to set up and use the CHC® E91 GNSS receiver. In this manual, “the receiver” refers to the E91 GNSS receiver unless otherwise stated. Even if you have used other Global Navigation Satellite Systems (GNSS) products before, CHC recommends that you spend some time reading this manual to learn about the special features of this product. If you are not familiar with GNSS, go to www.chcnav.com for an interactive look at CHC and GNSS. 1.1 Safety Information 1.1.1 Warnings and Cautions An absence of specific alerts does not mean that there are no safety risks involved. A Warning or Caution information is intended to minimize the risk of personal injury and/or damage to the equipment. WARNING - A Warning alerts you to a potential misused or wrong setting of the equipment. CAUTION - A Caution alerts you to a possible risk of serious injury to your person and/or damage to the equipment. 1.1.2 Regulations and Safety The receivers contain a built-in wireless modem for signal communication through Bluetooth® wireless technology or through external communication datalink. Regulations regarding the use of the wireless modem vary greatly from country to country. In some countries, the unit can be used without obtaining an end-user license. However, in some countries, the administrative permissions are required. For license information, consult your local dealer. Bluetooth® operates in license-free bands. Before operating a E91 GNSS receiver, determine if authorization or a license to operate the unit is required in your country. It is the responsibility of the end-user to obtain an operator's permit or license for the receiver for the location or country of use.
Introduction 8 1.1.3 Use and Care This receiver is designed to withstand the rough environment that typically occurs in the field. However, the receiver is high-precision electronic equipment and should be treated with reasonable care. CAUTION - Operating or storing the receiver outside the specified temperature range will cause irreversible damage. 1.2 Technical Support If you have a problem and cannot find the information you need in this manual or CHC website (www.chcnav.com), contact your local CHC dealer from which you purchased the receiver(s). If you need to contact CHC technical support, please contact us by email (support@chcnav.com) or Skype (chc_support). 1.3 Disclaimer Before using the receiver, please make sure that you have read and understood this User Guide, as well as the safety information. CHC holds no responsibility for the wrong operation by users and for the losses incurred by the wrong understanding about this User Guide. However, CHC reserves the rights to update and optimize the contents in this guide regularly. Please contact your local CHC dealer for new information. 1.4 Your Comments Your feedback about this user guide will help us to improve it in future revision. Please email your comments to support@chcnav.com.
Getting Started with E91 9 2 Getting Started with E91 2.1 About the Receiver The E91 GNSS receiver incorporates a GNSS engine, GNSS antenna, internal radio (410 MHz – 470 MHz), 3G cellular modem, Bluetooth, Wi-Fi, and dual-battery in a ruggedized and miniature unit that is easy for you to set up an all-in-one RTK rover or mobile base station. Bluetooth and Wi-Fi technology provide cable-free communication between the receiver and controller. The receiver can be used as the part of a RTK GNSS system with CHC LandStar 7 software. And you can download the GNSS data that recorded in the internal memory of receiver to a computer. To configure the receiver for performing a wide variety of functions, you can use the web interface by connecting the receiver with PC or smartphone through Wi-Fi. 2.2 Parts of the Receiver The operating controls are all located on the front panel. Battery compartment and SIM card slot are on the backside. Serial ports and connectors are located on the bottom of the unit. 2.2.1 Front Panel The following figure shows a front view of the receiver. The front panel contains six indicator LEDs and two buttons. Front panel
Getting Started with E91 10 Name Description Correction LED (Green) • Indicates whether the receiver is transmitting/receiving differential data. • The green LED flashes once per second when As a Base station: successfully transmitting differential data. As a Rover station: successfully receiving differential data from Base station. Satellite LED (Blue) • Shows the number of satellites that the receiver has tracked. • When the receiver is searching satellites, the blue LED flashes once every 5 seconds. • When the receiver has tracked N satellites, the blue LED will flash N times every 5 seconds. Static button (Yellow) • Move to next line of the menus or options. • Move to next character of the value that you want to make change. • Cancel the change you make on a function. Power button (Green) • Works as a Power button: Press and hold this button for 3 seconds to turn on or turn off the receiver. The green light will flicker when there is low battery. • Works as a Reset button: Hold Fn button, and press this button for 5 Power button Satellite LED Correction LED Static LED
Getting Started with E91 11 times continuously to reset the mainboard. 2.2.2 Receiver Ports Port Name Description IO port • This port is a 7-pin Lemo connector that supports RS-232 communications and external power input. • Users can use GPS to PC Data Cable supplied with the system to realize RS-232 communications between the receiver and computer or controller. Also, users can use a 7-pin cable to transmit differential data to an external radio. USB port • This port is a mini-USB connector that supports USB communications. • Users can use USB Cable supplied with the system to download the logged data to a computer. Radio antenna connector • Connect a radio antenna to internal radio of the receiver. And this connector is not used if you are using an external radio.
Getting Started with E91 12 2.3 Batteries and Power 2.3.1 Internal Batteries The receiver has internal rechargeable Lithium-ion battery, which can be charged by adapter. 2.3.1.1 Charging the Battery The rechargeable Lithium-ion battery is supplied partially charged. Charge the battery completely before using it for the first time. To charge the battery, first connect power adapter and cable then make supply from AC power. WARNING - Charge and use the rechargeable Lithium-ion battery only in strict accordance with the instructions. Charging or using the battery in unauthorized equipment can cause an explosion or fire, and can result in personal injury and/or equipment damage. To prevent injury or damage: •Do not charge or use the battery if it appears to be damaged or leaking. •Charge the Lithium-ion battery only in a CHC product that is specified to charge it. Be sure to follow all instructions that are provided with the battery charger. •Discontinue charging a battery that gives off extreme heat or a burning odor. •Use the battery only in CHC equipment that is specified to use it. •Use the battery only for its intended use and according to the instructions in the product documentation. 2.3.1.2 Battery Safe WARNING - Do not damage the rechargeable Lithium-ion battery. A damaged battery can cause an explosion or fire, and can result in personal injury and/or property damage. To prevent injury or damage: •Do not use or charge the battery if it appears to be damaged. Signs of damage include, but are not limited to, discoloration, warping, and leaking battery fluid. •Do not expose the battery to fire, high temperature, or direct sunlight.
Getting Started with E91 13 •Do not immerse the battery in water. •Do not use or store the battery inside a vehicle under hot weather condition. •Do not drop or puncture the battery. •Do not open the battery or short-circuit its contacts. WARNING - Avoid contact with the rechargeable Lithium-ion battery if it appears to be leaking. Battery fluid is corrosive, and contact with it can result in personal injury and/or property damage. To prevent injury or damage: •If the battery leaks, avoid with the battery fluid. •If battery fluid gets into your eyes, immediately rinses your eyes with clean water and seek medical attention. Please do not rub your eyes! •If battery fluid gets onto your skin or clothing, immediately use clean water to wash off the battery fluid. 2.3.2 External Power Supply Two methods are available for providing the external power to the receiver by the GPS to PC Data Cable+ Power Adapter, or GPS to PC Data Cable + external power cable (option purchase) + vehicle battery. In the office: The Power Adapter is connecting with AC power of 100-240V, the output port of the Power Adapter connects with the Power Port of the GPS to PC Data Cable.
Getting Started with E91 14 In the field: The external power cable is connecting with a vehicle battery, the output port of the external power cable connects with the Power Port of the GPS to PC Data Cable. WARNING - Use caution when connecting external power cable's clip leads to a vehicle battery. Do not allow any metal object to connect (short) the battery's positive (+) terminal to either the negative (-) terminal or the metal part of the vehicle battery. This could result in high current, arcing, and high temperatures, exposing the user to possible injury. 2.4 Product Basic Supply Accessories 2.4.1 Base Kit Basic Supply Item Picture E91 GNSS Receiver UHF Bar Antenna (410-470 MHz) USB Cable GPS to PC Data Cable Power Adapter with Cord
Getting Started with E91 15 H.I. Tape Extension pole Tribrach with optical plummet Auxiliary H.I. Tool Tribrach adaptor Transport Hard Case 2.4.2 Rover Kit Basic Supply Item Picture E91 GNSS Receiver UHF Bar Antenna (410-470 MHz) USB Cable
Getting Started with E91 16 GPS to PC Data Cable Power Adapter with Cord 2M Range Pole w/bag Auxiliary H.I. Tool Transport Hard Case 2.5 Connecting to an Office Computer The receiver can be connected to an office computer for serial data transfer or settings via a GPS to PC Data Cable. Before you connect to the office computer, ensure that the receiver is powered on by internal battery or external power. The following figure shows how to connect to the computer for serial data transfer or settings: GPS to PC Data Cable
Getting Started with E91 17 2.6 Connecting to a Controller 2.6.1 Connecting via Wi-Fi with LandStar 7 Software Turn on the controller → run LandStar 7 → go to Config main menu → tap Connect. In the Connect screen, select CHC for the Manufacture field, E91 for Device Type field, WIFI for Connection Type field. Tap the Wireless Lan icon on the right side to select the hot-spot → Switch on the WiFi module by the top switch → tap refresh button to search the hot spot around → select the target device in the list. Tap Connect to link to the hot spot. If the first-time connection to this hot spot, user may type in the password.
Getting Started with E91 18 Tip – The Wi-Fi key of the receiver is 12345678 by default. Tap the Connect button to build the connection. 2.6.2 Connecting via Bluetooth with LandStar 7 Software Turn on the controller → run LandStar 7 → go to Config main menu → tap Connect. In the Connect screen, select CHC for the Manufacture field, E91 for Device Type field, Bluetooth for Connection Type field. Tap the Bluetooth Manager and turn on the Bluetooth function to search bluetooth
Getting Started with E91 19 device around → select the target device in the list. Tap Pair to connect the bluetooth device → selected the target device in the bluetooth manager list Tap the Connect button to build the connection.
Getting Started with E91 20 2.7 Downloading Logged Data Data logging involves the collection of GNSS measurement data over a period at a static point or points, and subsequent post-processing of the information to accurately compute baseline information. Data logging using receivers requires access to suitable GNSS post-processing software such as the CHC Geomatics Office (CGO) Software. The procedures of downloading logged data in the receiver are as follows: Switch on the receiver and connect it with a computer by USB Cable. After the successful connection, a removable disk named as the Serial Number (SN) of the receiver will appear on the computer. Double click the removable disk and you will see the folder named as “repo”. Double click this folder, you will see 9 folders. The “push_log” folder is used to save the log files, and the other 8 folders represent different logging session and are used for store static data. Double click the folder that you have configured to store the static data, you will see the folder(s) created by the E91 system automatically and named by the date which is decide by GPS time when you start to log data. Select the destination folder and double click it, and then two folders named as different data format (hcn and rinex) will be displayed. Select the data format that you has configured to save the static data, you will find the static raw data.
Getting Started with E91 21 Tip – For hcn files, the name of the file is represented as XXXXXXDDDNN, where XXXXXX is the SN of the receiver, DDD is day of year, and NN is the recording session. WARNING – The static data will be saved in the first logging session, the “record_1” folder, by default. Old files will be deleted if the storage space is full. If you configure not to auto delete old files when the memory is low, the receiver will stop data logging.
Base Station Setup and Operation 22 3 Base Station Setup and Operation Real-Time Kinematic (RTK) operation provides centimeter-level precision by eliminating errors that are present in the GNSS system. For all RTK operations, you require both a rover receiver and a source of corrections from a base station or network of base stations. A base station consists of a receiver that is placed at a known point. The receiver tracks the same satellites that are being tracked by the rover receiver simultaneously. Errors in the GNSS system are monitored at the base station, and a series of position corrections are computed. The messages are sent through a radio link to the rover receiver, where they are used to correct the real time positions of the rover. This chapter provides the information to help you identify good setup locations, outlines basic precautions that you need to take to protect the equipment, and describes the conventional process to set up the base station and the configuring procedure that required for transmitting correction data. 3.1 Base Station Setup Guidelines For good performance, the following base station setup guidelines are recommended: • Place the GNSS receiver in a location on the worksite where equal range in all directions provides full coverage of the site. • Place the GNSS antenna in a location that has a clear line of sight to the sky in all directions. Do not place the antenna near vertical obstructions such as buildings, deep cuttings, site vehicles, towers, or tree canopy. • The GNSS antenna must have a dear line of sight to the sky at all times during operation. • Place the GNSS and radio antennas as high as practical. This minimizes multipath from the surrounding area, and enables the radio to broadcast to the maximum distance. • Choose the most appropriate radio antenna for the size of the worksite. The higher the gain on the antenna, the longer the range. • Make sure that the GNSS receiver does not lose power. To operate continuously for more than a few hours without loss of power at the base station, provide external power. When you use an external power supply, the integrated battery provides a backup power supply, enabling you to maintain continuous operation through a mains power failure. • Do not locate a GNSS receiver, GNSS antenna, or radio antenna within 400 meters (about 1,300 feet) of transmitters, such as a power radar or cellular
Base Station Setup and Operation 23 communications tower. • Do not set up the base station close to the sources of electromagnetic interference, include alternators and generators, electric motors, equipment with DC-to-AC converters, etc. • Do not operate the receiver outside the specified operating temperature range -40°C to +60°C (-40°F to +140°F). • Take reasonable care to keep the GNSS receiver equipment dry, which could prolong their life and reduce the effects of corrosion on ports and connectors. 3.2 Outputting Corrections Using Internal Radio Modem 3.2.1 Base Station Setup 1. Connect the radio antenna onto E91 receiver. Screw the receiver onto extension pole. 2. Screw the extension pole with auxiliary H.I. tool onto tribrach adaptor. 3. Mount the tribrach onto the tripod. 4. Insert the tribrach adaptor into the tribrach. 5. Level and plumb the receiver over the known (control) point. 6. Measure the height of the base station GNSS antenna by measuring the slant height from the known (control) point to the end of auxiliary H.I. tool. Note –After entered the vertical height from the known (control) point to the bottom of receiver that you calculated by adding the height of the extension pole to the height from the known (control) point to the auxiliary H.I. tool, LandStar 7 will calculate the height to the Antenna Phase Center (APC) automatically. 7. If required, connect the receiver to an external 12 V power supply. 3.3 Outputting Corrections Using External Radio For base receiver part: 1. Screw the E91 receiver onto extension pole. 2. Screw the extension pole with auxiliary H.I. tool onto tribrach adaptor. 3. Mount the tribrach onto the tripod. 4. Insert the tribrach adaptor into the tribrach.
Base Station Setup and Operation 24 5. Level and plumb the receiver over the known (control) point. 6. Measure the height of the base station GNSS antenna by measuring the slant height from the known (control) point to the auxiliary H.I. tool. Note – After entered the vertical height from the known (control) point to the bottom of receiver that you calculated by adding the height of the extension pole to the height from the known (control) point to the end of auxiliary H.I. tool, LandStar 7 will calculate the height to the Antenna Phase Center (APC) automatically. 7. If required, connect the receiver to an external 12 V power supply. For external radio part (take the CHC DL6 Datalink for example): 8. Connect the Datalink Antenna to the 3 meter Cable for Datalink Antenna. 9. Connect 3 meter Cable for Datalink Antenna to Datalink Antenna Mounting Pole. 10. Screw the Datalink Antenna Mounting Pole onto the tribrach adapter. 11. Mount the tribrach onto the tripod. 12. Insert the tribrach adaptor into the tribrach. 13. Set up the Datalink Antenna nearby the base receiver. 14. Fix the DL6 Datalink onto the tripod. 15. Place the car battery at an appropriate location. For connection between the receiver part and external radio part: 16. Connect Datalink Antenna to the Datalink Antenna Slot of DL6 Datalink via 3 meter Cable for Datalink Antenna. 17. Connect the base receiver with DL6 Datalink via GPS to Datalink Cable. 18. Connect the car battery with DL6 Datalink via Datalink External Power Cable. CAUTION – The Datalink Antenna must be connected to the Datalink before the Datalink is powered on; otherwise, the Datalink can be damaged.
Rover Station Setup And Operation 25 4 Rover Station Setup And Operation Real-Time Kinematic (RTK) operation provides centimeter-level precision by eliminating errors that are present in the GNSS system. For all RTK operations, you require both a rover receiver and a source of corrections from a base station or network of base stations. The second part of the RTK GNSS system is the rover receiver. The rover receiver is moved between the points that require measurement or stakeout. The rover receiver is connected to a base station or to a source of RTK corrections such as a CORS (Continuous Operational Reference System) or the CHC APIS service. The connection is provided by: • an integrated radio • an integrated cellular modem • a cellular modem in the controller This chapter provides the information to help you identify good setup locations, describes the conventional process to set up the rover station and the configuring procedure that required for receiving correction data. 4.1 Rover Station Setup Guidelines For good rover operation, observe the following setup guidelines: • Place the GNSS antenna in a location that has a clear line of sight to the sky in all directions. Do not place the antenna near vertical obstructions such as buildings, deep cuttings, site vehicles, towers, or tree canopy. GNSS rovers and the base station receive the same satellite signals from the same satellites. The system needs five common satellites to provide RTK positioning. WARNING – Take care not to touch overhead power lines with the CHC E91 GNSS receiver or the range pole when moving the equipment into position. Touching overhead power lines may cause electrocution, leading to serious injury. • GNSS satellites are constantly moving. Because you cannot measure at a specific location now does not mean that you will not be able to measure there later, when satellite coverage at the location improves. • To get a fixed position solution with centimeter precision, initialize the RTK rover receiver. For initialization to take place, the receiver must track at least five satellites that the base station is also tracking. In a dual-satellite constellation operation, for example, GPS and GLONASS, the receiver must
Rover Station Setup And Operation 26 track at least six satellites. • To continue to survey at centimeter precisions, the rover must continuously track at least four satellites that the base station is also tracking. The radio link between the base and rover receivers must also be maintained. • Loss of the satellite signals will result in a loss of centimeter position precision. 4.2 Rover Station Setup 1. If required, connect the radio antenna onto E91 receiver. 2. Screw the receiver on top of the range pole. 3. Fix the controller bracket on the range pole. 4. Fit the controller in the controller bracket. 5. Level and plumb the receiver over the target measuring point.
Configuring Through a Web Browser 27 5 Configuring Through a Web Browser Supported browsers: • Google Chrome • Microsoft Internet Explorer○R version 10, or higher To connect to the receiver through a web browser: 1. Turn on the Wi-Fi of the receiver. 2. Search the wireless network named as GNSS-XXXXXXX (the SN of your receiver) on your computer, and then establish the connection. 3. After the successful connection between your computer and the receiver, enter the IP address of the receiver into the address bar of the web browser on your computer: 4. The web browser prompts you to enter a login account and password: The default login account for the receiver is: ➢ Login Account: admin ➢ Password: password Note – Tick remember me option, and then the browser will remember the Login Account and Password you entered for the next time you enter this login screen. 5. Once you are logged in, the web page appears as follows:
Configuring Through a Web Browser 28 This web page shows the configuration menus on the left of the browser window, and the setting on the right. Each configuration menu contains the related submenus to configure the receiver and monitor receiver performance. This chapter describes each configuration menu. To view the web page in another language, select the corresponding language name from the dropdown list on the upper right corner of the web page. Currently, three languages are available: 5.1 Status Menu This menu provides a quick link to review the receiver's position information, satellites tracked, runtime, current data log status, current outputs, available memory, and more.
Configuring Through a Web Browser 29 5.1.1 Position Submenu This page shows the relevant position information about the receiver's position solution which including the position, DOP values, satellites used and tracked, and the receiver clock information. 5.1.2 Activity Submenu Lists several important items to help you understand how the receiver is being used and its current operating condition. Items include the identities of currently tracked satellites, internal and external storage usage rate, how long the receiver has been operational, state of the internal battery, power source state, files being logged, and data streams being output. With this information, it is easy to tell exactly what functions the receiver is performing:
Configuring Through a Web Browser 30 5.1.3 Google Map Submenu Tap this submenu to show the location of the receiver on Google map.
Configuring Through a Web Browser 31 5.2 Satellites Menu Use the Satellites menu to view satellite tracking details and enable/disable GPS, SBAS, GLONASS, BDS and Galileo constellations. These menus include tabular and graphical displays to provide all required information on satellite tracking status. 5.2.1 Tracking Table Submenu Provides the status of satellites tracked in general, such as the satellite ID, satellite type, attitude angle, azimuth angle, L1 SNR, L2 SNR, L5 SNR and enable/disable status of each one.
Configuring Through a Web Browser 32 5.2.2 Tracking Info. Table Submenu The following figure is an example of satellite track diagram page. Users can determine the satellite types and the corresponding SNR of L-band carriers to be displayed in any combination. 5.2.3 Tracking Skyplot Submenu The following figure is an example of Skyplot page. 5.2.4 Satellite Activation Submenu Use this menu to enable or disable satellites.
Configuring Through a Web Browser 33 5.2.5 Tracking Enable Submenu Use this menu to enable or disable tracking signals.
Configuring Through a Web Browser 34 5.3 Receiver Configuration Menu Use this menu to configure settings such as the antenna type and height, elevation mask and PDOP setting, the reference station coordinates, receiver resetting and web interface language: 5.3.1 Description This submenu shows the receiver information and reference station information, including antenna related information, elevation mask angle, reference station work mode and position, etc. 5.3.2 Antenna Configuration Submenu Use this screen to configure all of the items relating to the GNSS antenna. You must enter the correct values for all antenna-related fields, as the choices you make significantly affect the accuracy for logged data and broadcast correction data:
Configuring Through a Web Browser 35 5.3.3 Reference Station Settings Submenu Use this screen to configure settings such as the station coordinates and the broadcast station identifiers. You must enter accurate information in these fields, as this data significantly affects the accuracy of logged data files and broadcast correction data: For Reference Station Mode: There are three modes available: a) Auto Rover: The receiver will serve as a rover after this mode is enabled, and then receive correction data through the working mode set last time.
Configuring Through a Web Browser 36 b) Auto Base: The receiver will serve as a base after this mode is enabled, and then broadcast correction data based on coordinate inputted by user, or obtained through autonomous positioning automatically. c) Manual Base: The receiver will serve neither as a base or a rover after this mode is enabled. Users need to configure the receiver manually.
Configuring Through a Web Browser 37 For Reference Latitude and Reference Longitude: There are mainly three methods to enter the reference coordinates and shown as follows: a) Acquire Current Position: Click this button to acquire current position obtained through autonomous positioning automatically. b) Manual Input: Manually input the coordinate of a control point. c) From CORS: After the receiver logging in CORS, the software can record the coordinate of current position based on fix solution. For Sample for Average: Users can determine the positioning limit and sampling amount. The positioning limit falls into two types: a) Single Solution Coordinates: Collect the coordinates of receiver obtained through autonomous positioning. b) Fixed Solution Coordinates: Only collect coordinates of receiver with a fixed solution. After the configuration of positioning limit and sampling amount, click to carry out sampling and averaging → the progress bar will show the progress → the result
Configuring Through a Web Browser 38 will be served as the coordinate of current positon. If users need to save the changes, please tap button. 5.3.4 Receiver Reset Submenu Use this screen to completely or partially reset the receiver: 5.3.5 Languages Submenu Use this screen to select the web interface language: 5.3.6 User Management Submenu
Configuring Through a Web Browser 39 5.3.7 USB Function Switch Submenu Use this menu to switch between USB personal area network and Multimedia storage. 5.3.8 HCPPP Settings Submenu Use this menu to select HCPPP Range. 5.4 Data Recording Menu Use the Data Logging menu to set up the receiver to log static GNSS data and to view the logging settings. You can configure settings such as observable rate, recording rate, continuous logging limit, and whether to auto delete old files if memory is low. This menu also provides the controls for the FTP push feature: 5.4.1 Log Settings Submenu Here shows the data logging status, including internal and external storage usage and data logging status of each session. Also, users can configure the data logging settings for each session, including recording name, store location, storage limit, store formats, start time, etc.
Configuring Through a Web Browser 40 To edit the settings of each session, click the Modify button to the right of the required session, and then the Recording Edit screen appears: Click advanced to see more settings. In this screen, you can configure all the data logging parameters, and determine whether the recording files will be affected by the FTP Push. The parameters are
Configuring Through a Web Browser 41 mainly as follows: ➢ File Name: The name of this logging session. ➢ Sample Interval: Select the observable rate from the dropdown list. ➢ Store Location: Determine whether to store at internal storage or external storage. ➢ Enable Start Time: Set the start time of data logging in UTC. Select Or not option below to determine whether to start data logging from the start time defined, or immediately after this session is switched on. ➢ Duration Time: Set the duration of data logging. ➢ Assigned Storage: Set the storage space of this session. ➢ Circulating Memory: Select Yes or No option to determine whether to auto delete old files if the storage space is full. ➢ Data Format: Set the data format of the logged data. ➢ FTP Push: Decide whether to push the stored files to the FTP server of your choice. Tap button to save the settings and back to the Log Settings screen. Also, users can click to abandon the changed settings and back to Log Settings screen. Note – To modify data logging parameters, make sure the data logging session is switched off. To switch on or off ANY data logging session, tap the ON or OFF button to the right of the required session. To delete the recorded files of ANY data logging session, tap the Clear button to the right of the required session. To delete the recorded files of ALL data logging sessions, tap the Clear ALL Accounts button. 5.4.2 FTP Push Settings Submenu Use this screen to configure the receiver to push stored files to the FTP server of your choice. Only files that are configured to use FTP push are transmitted.
Configuring Through a Web Browser 42 Tap Modify button to the right of the required FTP server and the FTP Push Settings screen appears: 5.4.3 FTP Push Log Submenu Shows the related information about the recorded filed that be pushed. And users can tap Clear Ftp Send Log button in the upper right corner to clear the log of FTP Push operations. 5.4.4 Data Download Submenu In this submenu, users can download the data files that recorded in the internal storage through the internal FTP site. 1. Click this submenu, and then the log on dialogue box will prompt you to enter a user name and password:
Configuring Through a Web Browser 43 The default logon account for the internal FTP site is: ➢ User name: ftp ➢ Password: ftp 2. Click the directory named as “repo” to view and download the files currently stored on the receiver: 3. To find the file need to be downloaded, click the name of data logging session → the date of file that be recorded → the format of the file → the name of the target file. 4. To download a file, left-click the name of the target file → download the file according to the prompts.
Configuring Through a Web Browser 44 5.5 IO Settings Menu Use the IO Settings menu to set up all receiver outputs and inputs. The receiver can output CMR, RTCM, Raw data, Ephemeris data, GPGGA, GPGSV, on TCP/IP, UDP, serial port, or Bluetooth ports. 5.5.1 IO Settings Submenu The following figure shows an example of the screen that appears when you select this submenu. In this submenu, users can configure 6 types of input and output settings. 1. RTK Client After configuring the settings of RTK client, users can log on CORS or APIS. Tap the Connect button to the right → the IO Settings screen will appear → choose one of the connection protocols among the NTRIP, APIS_BASE and APIS_ROVER → configure the related parameters → click to log on CORS or APIS. ➢ Connection Protocol: NTRIP
Configuring Through a Web Browser 45 ➢ Connection Protocol: APIS_BASE ➢ Connection Protocol: APIS_ROVER ➢ Connection Protocol: TCP
Configuring Through a Web Browser 46 2. TCP/UDP/NTRIP Tap the Connect button to the right of required TCP/UDP Client → the IO Settings screen will appear → select the connection protocol between TCP and UDP → enter the IP and Port of the target server → configure messages that you want to output to the target server → click to save and complete the connection. ➢ Connection Protocol: TCP ➢ Connection Protocol: UDP
Configuring Through a Web Browser 47 ➢ Connection Protocol: NTRIP1.0 ➢ Connection Protocol: NTRIP2.0
Configuring Through a Web Browser 48 3. TCP Server/NTRIP Caster Tap the Connect button to the right of required TCP Server/NTRIP Caster → the IO Settings screen will appear → select one of the connection protocols between NTRIP and TCP → configure the other related parameters → click to save the settings and open the server. ➢ Connection Protocol: TCP
Configuring Through a Web Browser 49 ➢ Connection Protocol: NTRIP 4. Serial Port Tap the Settings button to the right of Serial Port → the Serial Port Setup screen will appear → select Baud Rate used to transmit data → configure the messages that you want to output through the serial port → click to save the settings and start to transmit.
Configuring Through a Web Browser 50 5. Bluetooth Tap the Settings button to the right of Bluetooth → the Bluetooth Set screen will appear → configure the messages that you want to transmit through Bluetooth → click to save the settings and start to transmit. 6. Radio Tap the Settings button to the right of Radio → the Radio Settings screen will appear → select the format of differential data that you want to transmit
Configuring Through a Web Browser 51 through radio from the dropdown list → click to save the settings and start to transmit. 5.6 Network Setting Menu Use this menu to view network information, configure the receiver’s mobile network, set email alert for specific situation, configure HTTP or HTTPS port, and the user name and password of internal FTP site: 5.6.1 Description Submenu Use this submenu to check the information of network setting.
Configuring Through a Web Browser 52 5.6.2 Mobile Network Setting Submenu Use this submenu to configure GPRS model, network module and modify dialing status.
Configuring Through a Web Browser 53 5.6.3 Email Alarm Submenu Use this submenu to choose which situation of receiver will be alerted and input the email address.
Configuring Through a Web Browser 54 5.6.4 HTTP Submenu Use this submenu to configure HTTP port.
Configuring Through a Web Browser 55 5.6.5 HTTPS Submenu Use this submenu to configure HTTPS port. 5.6.6 FTP Service Submenu Use this submenu to configure the user name and password of internal FTP site. 5.7 Module Setting Menu Use this menu to check module information, configure WiFi, bluetooth, radio related settings, and turn on/off static voice of buzzer:
Configuring Through a Web Browser 56 5.7.1 Description Submenu Use this submenu to check the information of WiFi module, bluetooth module and radio module. 5.7.2 WiFi Submenu Use this submenu to turn on/off WiFi function and modify password.
Configuring Through a Web Browser 57 5.7.3 Bluetooth Settings Submenu Use this submenu to turn on/off bluetooth function and modify PIN number. 5.7.4 Radio Settings Submenu Use this submenu to turn on/off radio function and configure radio parameters.
Configuring Through a Web Browser 58 5.8 Firmware Menu Use this menu to check the current firmware information, download the system log, update the receiver firmware, download or update the configuration file and register the receiver, and more:
Configuring Through a Web Browser 59 5.8.1 Firmware Info Submenu Use this submenu to check the current firmware information. The following figure shows an example of the firmware information. 5.8.2 Hardware Version Submenu Use this submenu to check the hardware information, including main board version and core board version: 5.8.3 Config File Submenu Use this submenu to update Configuration File.
Configuring Through a Web Browser 60 5.8.4 System Log Download Submenu Use this submenu to download the system log of the receiver. 5.8.5 User Log Submenu 5.8.6 Firmware Update Submenu Use this submenu to load new firmware to the receiver across the network. Tap the Browse button to locate the upgrade file → tap Confirm button to confirm the selected upgrading file and start upgrading.
Configuring Through a Web Browser 61 Notes • It may take about 3 or 4 minutes to complete the firmware upgrading. Do not touch the power button or unplug the power until the upgrading process is finished, or damage will be caused to the receiver. • The receiver will restart after the firmware upgrading is done, so users need to reconnect the receiver with your computer via Wi-Fi, and then log-in the receiver through a web browser to continue the configuration. 5.8.7 GNSS Board Upgrade Submenu Use this submenu to upgrade GNSS Board. 5.8.8 Radio Upgrade Submenu Use this submenu to browse upgrade file and upgrade radio. 5.8.9 Upgrade Online Submenu Use this submenu to input Server Address and upgrade online.
Configuring Through a Web Browser 62 5.8.10 GNSS Registration Submenu Use this submenu to register the receiver. Paste or enter the registration code to the Registration Code field → tap Registration button to complete the registration. 5.9 Cloud Service Setting Menu 5.9.1 Cloud Service Setting Submenu Use this submenu to turn on or turn off Cloud Service, Auto Start, Remote Control and configure other settings .
Configuring Through a Web Browser 63
A Communication Ports Definition 64 A Communication Ports Definition AI CHC E91 Receiver IO Port (7-pin Lemo Port) Definition PIN FUNCTION 1 Ground ( - ) 2 Ground ( - ) 3 RS232-TX (Output) 4 PPS 5 Not Used 6 VIN 7 RS232-RX (Input)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 50cm between the radiator & your body.
CHC - Shanghai Huace Navigation Technology Ltd. 599 Gaojing Road, Building D Shanghai, 201805, China Tel: +86 21 542 60 273 Fax: +86 21 649 50 963 Email: sales@chcnav.com | support@chcnav.com Website: www.chcnav.com

User Manual

Page 1 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 2 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 3 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 4 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 5 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 6 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 7 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 8 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 9 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 10 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 11 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 12 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 13 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 14 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 15 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 16 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 17 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 18 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 19 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 20 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 21 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 22 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 23 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 24 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 25 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 26 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 27 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 28 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 29 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 30 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 31 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 32 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 33 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 34 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 35 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 36 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 37 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 38 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 39 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 40 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 41 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 42 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 43 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 44 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 45 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 46 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 47 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 48 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 49 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 50 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 51 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 52 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 53 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 54 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 55 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 56 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 57 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 58 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 59 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 60 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 61 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 62 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 63 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 64 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 65 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual
Page 66 of Huace Navigation Technology A01013 Geodetic GNSS Receiver E91 User Manual

Navigation menu