Huawei Technologies AP6010SN-GN WLAN Access Point User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1763670
Application ID	IcWqGBPtVSS4zUsKQGCTTA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	77.35kB (966845 bits)
Date Submitted	2012-08-10 00:00:00
Date Available	2013-02-06 00:00:00
Creation Date	2012-06-12 20:26:29
Producing Software	Microsoft® Office Visio® 2007
Document Lastmod	2012-06-12 20:26:29
Document Title	User Manual
Document Creator	Microsoft® Office Visio® 2007
Document Author:	huawei

AP6010SN-GN Wireless LAN Access Point
Quick Start Guide
HUAWEI TECHNOLOGIES CO., LTD.
Copyright © Huawei Technologies Co., Ltd. 2012. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of
Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or
part of the products, services and features described in this document may not be within the purchase scope or the usage
scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are
provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the preparation
of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document
do not constitute the warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address:
Administration Building,Huawei Technologies Co.,
Ltd.,Bantian,Longgang District,Shenzhen,People’s Republic of China
Postcode: 518129
Website: http://www.huawei.com
Email:
support@huawei.com
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol
CAUTION
NOTE
Description
Indicates a potentially hazardous situation, which if not avoided, could
result in equipment damage, data loss, performance degradation, or
unexpected results.
Provides additional information to emphasize or supplement important
points of the main text.
Change History
Changes between document issues are cumulative. Therefore，the latest document issue contains all the
Changes in previous issues.
Change in Issue 01 (2012-05-30)
Initial commercial release.
AP6010SN-GN
Quick Start Guide
Please download the detailed product documents from "http://support.huawei.com/support/".
The dEtaIled path is as follows: Technical Support->Documentation->Access Network -> WLAN ->WLAN -> Product
Documentation ->AP6010SN.
Before performing Installation, confirm that the installation accessories and tools are available.
Installation accessories:
Installation tools:
Technical Support
Combination Diagonal Adjustable
Flat-head
Phillips
pliers
pliers
wrench
screwdriver screwdriver
Sheetmetal
wall-mounting
bracket
Expansion
bolt
Maker
Wire
stripper
Utility knife
Hammer
COAX Measuring 6mm drill
ESD
bit
gloves crimping tool tape
Level
Huawei Technologies Co., Ltd.
Address:Administration Building,Huawei
Technologies Co., Ltd.,Bantian,Longgang
District,Shenzhen,People’s Republic of
China
Postcode:518129
Email:support@huawei.com
Website:http://www.huawei.com
RJ45
Hammer Multimeter Vacuum Network
cleaner Cable tester
Crimping tool
drill
Cable
cutter
Packing List
Unpack the equipment. Ensure that all items listed in the package list are included in the shipment. If any item is missing,
contact the supplier.
Quantity Unit
Item
Quantity
Item
Unit
AP device
PCS
Warranty card
PCS
Power adapter（Optional）
PCS
Certificate of Conformance
PCS
Sheetmetal wall-mounting bracket
PCS
Expansion bolt
PCS
Quick Start Guide (including the printed
packing list)
PCS
Toxic or Hazardous Substance & Elements
Declaration
PCS
Device Overview
Indicators
Front view
2 3
Indicator and Interfaces
Perspective
No.
Name
Indicator
DC 12V
Connected to the power adapter.
Default
Press and hold down the Reset button for 3 seconds
to restore the factory settings and restart the AP.
ETH/PoE
Console
Description
For details about indicator, see the Power-on.
Connected to a PoE power supply or switch, or
connected to the Ethernet.
Connected to the maintenance terminal.
Installing the AP
Select an appropriate installation position and leave 20 cm space above and around the device for cooling air circulation.
AP6010SN dimensions (unit: mm) without a backplane support
50
180
180
Recommended AP6010SN installation space (unit: mm)
The AP6010SN can be installed onto a workbench or mounted against a wall. In addition, the AP6010SN can be mounted
to a T-rail and mounted against the ceiling.
Wall-mount the AP6010SN using the plastic wall-mounting bracket:
1. Fix the wall-mounting bracket to the wall, adjust the
installation position, and use the marker to mark the drilling
positions where expansion bolts are installed.
2. Use #6 drill bit to drill 25-30 mm deep holes in the
drilling positions. Hammer the expansion tubes into
the holes until the expansion tubes are embedded into
the wall.
85mm
59mm
4. Align the holes at the rear side of the AP with the
hooks on the bracket and hang the AP on the bracket.
Hold the AP with one hand and press the AP
downwards with another hand to secure the AP on the
wall.
3. Fix the wall-mounting bracket to the wall, use the
Phillips screwdriver to fasten three self-tapping screws
into the expansion tube.
Field
Field
strength
strength
场强示意
场强示意
Underfloor
cabling
Installing the AP
Ceiling-mount the AP6010SN using the sheetmetal wall-mounting bracket:
1. Remove the ceiling, determine locations of mounting holes based on the distance between two installation holes,
use the hammer drill to drill holes, and fix the wall-mounting bracket to the ceiling.
Ceiling
Adjustable
buckle
35mm
M4*30 screw
2. Align the cucurbit holes at the rear side of the AP with four screws on the wall-mounting bracket and secure the AP.
Ceiling
Adjustable buckle
Wall-mounting
bracket
Mounting the AP6010SN to the T-rail using the sheetmetal wall-mounting bracket:
2. Align the cucurbit holes at the rear side of the AP with
four screws on the wall-mounting bracket and secure the
AP.
1. Use screws to fix the adjustable buckle to the wallmounting bracket, hook the adjustable buckle to the Trail, and secure the screw on the adjustable buckle to
fasten the wall-mounting bracket and T-rail.
T-rail
Adjustable buckle
M3*6 screw
CAUTION
Ensure that the AP is correctly installed on the wall-mounting bracket and there must be 20 cm space above and around
the AP for cooling air circulation.
NOTE
To prevent unauthorized personnel from moving the AP, lock the AP using the security lock and determine the position
for installing the security lock. When the sheetmetal wall-mounting bracket is used, fasten the security lock to the wallmounting bracket or other immovable object. The following figure shows the security lock. The carrier should purchase
the security lock.
Security lock
Lock hole
Connecting Cables
Connect the network cable to the AP
No.
Description
Item
● The AP6010SN supports PoE power supply and DC power supply.
Power
● When both the PoE power supply and DC power supply are available, the DC power
adapter 12 V
supply is used.
DC
● When DC power supply is used, use the specified power adapter; otherwise, the device may
be damaged.
Network
cable
If the AP needs to connect to the Ethernet, ensure that the Ethernet cable is working
properly. If the Ethernet cable is not working properly, for example, RJ45 connectors are shortcircuited, the AP may fail to be powered on or fail to work. Before connecting an Ethernet cable
to the AP, use the cable test tool to check whether the cable is qualified. If the cable is
unqualified, replace it.
Requirements for making a network cable:
● Cut the cable of proper length based on the distance between the AP and the PSE device, peel the insulation on
both ends of the network cable, and crimp the wires to RJ45 connectors.
● Connect RT45 connectors to the network cable tester to test cable connectivity. The following shows the pin
assignment.
X1 Pin
Wire Color
White and orange
Orange
White and green
X2 Pin
Blue
White and blue
Green
White and brown
Brown
CAUTION
● The service network cable cannot be connected to the console port. Otherwise, the AP6010SN may be damaged
when using PoE power supply.
● Before connecting the cable to the AP, coil the cable around the wall-mounting bracket first. This prevents the cable
from being bent.
Power-on
NOTE
Power on the AP6010SN and check the indicator status to determine the
System running status.
Type
Default status
Color
Frequency
Green
Steady on
UBOOT:
The AP is just powered on.
The system is running properly, the Ethernet connection is
0.5 Hz
Running
Description
correct,and STAs are associated with the AP.
Green
The system is running properly, the Ethernet connection is
0.2 Hz
correct, no user is connected, and the system is in low power
consumption state.
Alarm
Green
1. The AP is being upgraded.
2. The CAPWAP tunnel is disconnected.
3. The AP is running properly, but does not go online.
4 Hz
A fault that affects services occurs and cannot be rectified
Error
Red
Steady on
automatically. For example, the system fails to load the DRAM or
system software. The fault needs to be rectified manually.
Technical Specifications
Item
Weight
Description
400g
Dimensions (H x W x D)
50mm×180mm×180mm
Output: DC 12V ±10%
12 V DC (Power adapter)
Input: 100V ~240V AC
PoE power
-48V
Operating temperature
Relative humidity
-10℃ to +50℃
10% to 95%
Pressure
70kPa to 106kPa
Altitude
–60 m to 4000 m
Logging In to the Router
After an AP is powered on, you can log in to the AP using the following methods.
1. Logging In to the AP Through the Console Port
This section describes how to log in to the AP through the console port. After logging in to the AP, you can configure
the AP using commands.
2. Logging In to the AP Using Telnet
This section describes how to log in to the AP using Telnet. After logging in to the AP, you can configure the AP using
commands.
1. Logging In to the AP Through the Console Port
This section describes how to log in to the AP through the console port. After logging in to the AP, you can configure the
AP using commands.
Procedure
Step 1 Connect a PC to the AP with a console cable. Connect the RJ45 connector to the console port of the AP and
connect the DB9 connector to the serial port of the PC. Figure 1-1 shows the location of the AP's console port.
Figure 1-1
Location of the AP's console port
No
Port
Console port
Step 2 Run the terminal emulation program on the PC. For example, to open the HyperTerminal of Windows XP on
the PC, choose Start > Programs > Accessories > Communications > HyperTerminal. Enter the name of
the new connection in the Name text box and click OK, as shown in Figure 1-2.
Figure 1-2
Setting up a connection
Logging In to the Router
Step 3 Select the serial port used on the PC and click OK, as shown in Figure 1-3.
Figure 1-3
Selecting the connected port
Step 4 Click Restore Defaults, select 9600 bit/s from the Bits per second drop-down list box, and click OK, as shown
in Figure 1-4.
Figure 1-4
Setting communication parameters
Step 5 Press Enter on the subsequent dialog boxes until the command line prompt of the user view, such as
, is displayed.
You can run commands to configure the AP. Enter a question mark (?) whenever you need help.
----End
Logging In to the Router
2. Logging In to the AP Using Telnet
This section describes how to log in to the AP using Telnet. After logging in to the AP, you can configure the AP using
Commands.
Procedure
Step 1
Connect a PC to the uplink port of the AP with a network cable. Figure 1-5 shows the location of the AP's uplink
port.
Figure 1-1
Location of the AP's uplink port
No
Port
ETH/PoE
Step 2
Configure a static IP address for the PC. The IP address must be on the network segment 192.168.0.1/24
(The IP address should not be same as the AP's default IP address 192.168.0.1.) and the subnet mask is
255.255.255.0.
After the configuration is complete, run the ping 192.168.0.1 command on the PC to check whether the PC
can be pinged. If the ping operation succeeds, the connection is set up successfully. If the ping operation fails,
The connection fails to be set up. Check whether the network cable works properly.
Step 3
Access the command line window on the PC. For example, if the PC runs Windows XP, choose Start > Run
And enter cmd in the displayed dialog box.
Step 4
Run the telnet 192.168.0.1 command to log in to the AP.
Step 5
Enter the default user name and password admin. If the user view is displayed, you have logged in
Successfully.
When you log in for the first time, the following page is displayed:
Username: super
Password:
Enterprise AP:
----End
10
AP Local Configuration
WLAN services parameters of an AP are configured on the AC that is connected To the AP, and then delivered to the AP.
The following parameters are configured on the AP through Telnet or the console port.
1. Configuring the AP Access Mode
This section describes how to configure the mode in which an AP goes online.
2. Configuring VLANs on Wired Interfaces of an AP
This section describes how to configure VLANs on wired interfaces of an AP.
3. Configuring WDS (Applicable to Only AP6010DN)
This section describes how to configure WDS parameters on an AP.
Configuring the AP Access Mode
This section describes how to configure the mode in which an AP goes online.
● AP Access Modes
After an AP starts, going online management module determines the mode in which the AP goes online. Users are
unaware of the AP access mode. In the AP startup phase, the AP obtains the its IP address, the gateway IP address,
and the AC IP address based on the access mode. After obtaining all the information, the AP sets up a Control And
Provisioning of Wireless Access Point (CAPWAP) link with the AC. The process is as follows:
1. The AP reads the configuration file and determines the mode to go online.
2. If the DHCP mode is used, the AP starts the DHCP process.
3. If the static mode is used, the AP starts the AC discovery process based on the static configuration, and
establishes a control tunnel with the discovered AC.
4. If the PPPoE mode is used, the AP initiates the PPPoE dial-up process. After obtaining the management IP
address and gateway address, the AP uses the statically configured AC IP address to discover the AC, and
establishes a control tunnel with the AC.
NOTE
By default, AP's go online in DHCP mode.
●
Configuring the Mode for an AP to Go Online
● Configuring the AP to go online in DHCP mode
1. Use Telnet to log in to the AP from a PC.
login：admin
Password：
//The default password is admin.
~ #
2. Configure the AP to go online in DHCP mode.
~ # cli
Enterprise AP# configure interface ethernet
// Enter the AP interface view.
Enter Ethernet configuration commands，one per line.
Enterprise AP (if-ethernet) # ip mode dhcp
// Set the mode in which the AP goes online.
Please reboot the AP，configuration will take effect
Enterprise AP (if-ethernet) #
3. Restart the AP to make the configuration take effect.
~ # reboot
● Configuring the AP to go online using a static IP address
1. Use Telnet to log in to the AP from a PC.
login: admin
Password:
//The default password is admin.
~ #
2. Configure the AP to go online using a static IP address. The configuration items are the IP address of an AC that
is connected to the AP, the AP's IP address (mandatory), the mask address (mandatory), and the gateway
address (not required when in Layer 2 networking).
~ # cli
Enterprise AP# configure interface ethernet
// Enter the AP interface view.
Enter Ethernet configuration commands，one per line.
Enterprise AP (if-ethernet) # ip mode static // Set the mode in which the AP goes online.
Enterprise AP (if-ethernet) # ac iplist 1.1.1.1 // Configure the IP address of an AC that is connected to the AP.
Enterprise AP (if-ethernet) # ip address 192.168.60.2 255.255.255.0 192.168.60.1 // Configure the IP
address of the AP.
Please reboot the AP，configuration will take effect
Enterprise AP (if-ethernet) #
3. Restart the AP to make the configuration take effect.
~ # reboot
11
AP Local Configuration
● Configuring the AP to go online in PPPoE mode
1. Use Telnet to log in to the AP from a PC.
login: admin
Password:
// The default password is admin.
~ #
2. Configure the AP to go online in PPPoE mode.
~ # cli
Enterprise AP# configure interface ethernet
// Enter the AP interface view.
Enter Ethernet configuration commands, one per line.
Enterprise AP (if-ethernet) # ip mode pppoe
// Set the mode in which the AP goes online.
Please reboot the AP, configuration will take effect
Enterprise AP (if-ethernet) #
3. Configure a user name and password for going online in PPPoE mode. By default, the user name and password are
both wlan@huawei and the password type is simple.
Enterprise AP(if-ethernet) # user admin password simple admin //Set the user name and password to admin.
4. Restart the AP to make the configuration take effect.
~ # reboot
NOTE
● After the configuration is complete, run the reboot command to restart the AP.
● After the configuration is complete, run the show sysinfo command to check the configuration.
Enterprise AP(if-ethernet) # show sysinfo
ap_ipmode=pppoe
ap_ipaddr=
ap_ipversion=4
ap_netmask=
ap_gateway=
ac_ip1=
ac_ip2=
ac_ip3=
ac_ip4=
pppoe_username=wlan@huawei
pppoe_pwd_type=simple
pppoe_password=wlan@huawei
2. Configuring VLANs on Wired Interfaces of an AP
This section describes how to configure VLANs on wired interfaces of an AP.
● Introduction to the Wired Interfaces
A wired interface on an AP is connected to an AC or a switch. When the AP assigns service VLANs to packets, you can
configure VLANs on wired interfaces of the AP.
● Configuring VLANs on a Wired Interface
NOTE
By default, the PVID of a wired-side interface is 0, and no VLAN is configured on the interface.
1. Use Telnet to log in to the AP from a PC.
login: admin
Password:
//The default password is admin.
~ #
2. Configure VLANs and PVID on the wired interface.
~ # cli
Enterprise AP# configure interface ethernet
// Enter the AP interface view.
Enter Ethernet configuration commands，one per line.
Enterprise AP (if-ethernet) # ether-port 0 [1-4095] [tag/untag]
// Configure the VLANs allowed by the wired
interface.
Enterprise AP (if-ethernet) # ether-port 0 pvid [1-4095]
//Configure the PVID of the wired interface.
NOTE
The configuration takes effect immediately, and you do not need to restart the AP.
12
AP Local Configuration
3. Configuring WDS (Applicable to Only AP6010DN)
This section describes how to configure WDS parameters on an AP.
● Introduction to WDS
WDS enables multiple AP6010DNs to establish wireless links to connect two or more wired or wireless LANs. WDSenabled AP6010DNs can switch data packets between the LANs. WDS facilitates network deployment, and device
installation, and allows flexible networking.
● Configuring WDS
Most WDS parameters are configured on the AC. For details, see the AC configuration guides. On an AP, you can enable
or disable the radio indicator that indicates the signal strength of the last hop bridge, and configure the WDS keys.
● Enabling/Disabling the radio indicator that indicates the signal strength of the last hop bridge.
NOTE
By default, the radio indicator is enabled on an AP6010DN.
1. Use Telnet to log in to the AP from a PC.
login: admin
Password:
// The default password is admin.
~ #
2. Enabling/Disabling the AP's radio indicator
Enterprise AP (config) # configure interface wireless 0 (1)
// Enter the 2.4G 5G interface view.
Enter Wireless configuration commands,one per line.
Enterprise AP (if-wireless 0 (1)) # wds led flag 0 (1)
// Enable/Disable the AP's radio indicator.
Please reboot the AP,configuration will take effect
3. Restart the AP to make the configuration take effect.
~ # reboot
● Configure the WDS key.
1. Use Telnet to log in to the AP from a PC.
login: admin
Password:
// The default password is admin.
~ #
2. Configure the WDS key.
Enterprise AP (config) # configure interface wireless 0
// Enter the 2.4G 5G interface view.
Enter Wireless configuration commands, one per line.
Enterprise AP (if-wireless 0 (1) ) # wds psk 0 (1) 111111
// Set the key type to hex (parse) and the key to
111111.
3. Restart the AP to make the configuration take effect.
~ # reboot
NOTE
After the configuration is complete, run the reboot command to restart the AP.
13
Declaration on Hazardous Substances in Electronic
Information Products
Hazardous Substances
Part
Pb
Hg
Cd
Cr6+
PBB
PBDE
Mechanical part
Board/circuit module
Signal cable
Cable connector
Power adapter
Auxiliary equipment
O: Indicates that the concentration of the hazardous substance contained in all the homogeneous materials of this
part is below the limit requirement of the SJ/T 11363-2006 standard.
X: Indicates that the Concentration of the hazardous substance contained in all the homogeneous materials of this
part is above the limit requirement.
QUALIFICATION CARD
14
Warranty Card
Thank you for choosing HUAWEI Technologies Co., Ltd-a leading telecom solution provider. To get better services, please
read this warranty card carefully, fill in the required information and preserve this card in good condition.
Your Name
Address/Postal Code
Telephone
Product Type
Product Serial Number
Purchase Date
Invoice Number
Dealer Name
Dealer´s Address/Telephone
Preserve well. No reissue
Dealer´s Seal: Limited Warranty
Subject to the exclusions contained below, Huawei Technologies CO., Ltd. (hereinafter referred to as Huawei) warrants its
access terminals ("Products") to be free from defects in materials and workmanship under normal consumer usage for one
year from the date of purchase of the product ("Warranty period"). During the warranty period，a Huawei authorized
service partner shall remedy defects in materials and workmanship free of charge.
Special Notice:
1. The warranty card shall be applicable only after being stamped by the dealer.
2. The warranty card must be preserved in good condition and free of any scratch or alteration.
3. To claim such service for defects that are not included in The following exclusion terms, the warranty card and the
invoice that records the product serial number shall be presented to a Huawei authorized service partner.
Exclusions:
In any of the following cases, the warranty card becomes unenforceable or inapplicable without prior notice:
1. The defects are caused by improper handling in transportation and assembly.
2. The defects are caused by the fact that the product is dismantled or altered by anyone that is not from a Huawei
authorized service partner.
3. The defects are caused by the fact that the product is used in a harsh environment that is not suitable for the operation
of the product.
4. The defects are caused by any force majeure including but not limited to fire, earthquake, lightning and tsunami.
5. The defects are caused by the fact that the product is used or handled improperly, roughly or not as instructed in the
applicable User Guide.
6. The normal wear and tear, including but not limited to the normal wear and tear of the shell and the power module, shall
not be covered by the limited warranty.
7. The warranty card is altered or illegible, or the product serial number recorded on the warranty card is inconsistent with
the actual one imprinted or labeled on the product.
In any case that is not covered by this limited warranty or should the warranty expire，Huawei shall charge for the
service(s) claimed for the products if the product is still remediable.
Huawei preserves the right for interpretation of this limited warranty.
Huawei Technologies Co., Ltd.
Huawei Industrial Base, Bantian, Longgang,
Shenzhen 518129, People's Republic of China
http://www.huawei.com
15
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
www.huawei.com
Part Number: 31505361 Issue: 01

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 17
Language                        : zh-CN
Tagged PDF                      : Yes
Title                           : 
Author                          : huawei
Subject                         : 
Create Date                     : 2012:06:12 20:26:29+08:00
Modify Date                     : 2012:06:12 20:26:29+08:00
Producer                        : Microsoft® Office Visio® 2007
Creator                         : Microsoft® Office Visio® 2007

EXIF Metadata provided by EXIF.tools