Huawei Technologies ATU-LX3 Smart Phone User Manual ATU LX3 QSG Dual huawei cover

Huawei Technologies Co.,Ltd Smart Phone ATU LX3 QSG Dual huawei cover

UserManual.wiki >

Huawei Technologies >

ATU-LX3 User Manual >

Contents

1. Users Manual
2. User Manual

User Manual

Quick Start GuideATU-LX3

Your Device at a GlanceBefore you start, let's take a look at your new device.lTo power on your device, press and hold the power buttonuntil the screen turns on.lTo power off your device, press and hold the power button,and then touch .lTo restart your device, press and hold the power button,and then touch .lPress and hold the power button for 10 or more seconds toforcibly restart your device.1234567891014131211Rear camera Front cameraStatus indicator Card trayInfrared sensor Micro-USB portSpeaker Power buttonVolume button EarpieceSmart SeleButterighting Flash1

Secondary microphone Headset jacklTo force your device to restart, press and hold thepower button until your device vibrates.2

Getting StartedlEnsure that the card is correctly aligned and that thecard tray is level when you insert it into your device.lBe careful not to scratch your device or hurt yourselfwhen using the eject pin.lStore the eject pin out of the reach of children toprevent accidental swallowing or injury.lDo not use cut or modied SIM or microSD cards withyour device as these may not be recognized and coulddamage the card tray (slot).Follow the instructions in the following gures to set up yourdevice. Please use the eject pin included.Dual-SIM:3

Dual Card Dual Standby SinglePass (dual-SIM devices only)Your device supports only dual card dual standby single pass,which means you cannot use both SIM cards for calls or dataservices simultaneously.lWhen you are on a call using SIM card 1, SIM card 2 cannotbe used to make or answer calls. If someone calls SIM card2, the caller will hear a voice message similar to "Thesubscriber you dialed is out of the service area" or "Thesubscriber you dialed cannot be connected for the moment,please try again later." The actual message will vary byservice provider.lWhen you are using SIM card 1's data service, SIM card 2'sdata service will be disabled.Your device's single pass feature helps reduce powerconsumption and increase your device's standby time. It is notrelated to your service provider's network conditions.You can go to Settings > Wireless & networks > Dual SIMsettings, and enable Enable call forwarding between SIMsto avoid the conicts mentioned above.4

For More InformationIf you encounter any problems while using your device, youcan obtain help from the following resources:lGo to Tips for function details and usage tips.lVisit http://consumer.huawei.com/en to view deviceinformation, frequently asked questions and otherinformation.lVisit http://consumer.huawei.com/en/support for the mostup-to-date contact information for your country or region.Go to Settings and touch System > About phone > Legal toview legal information for your product.Go to Settings and touch System > About phone > Legal >Safety information to view safety information for yourproduct.Go to Settings and touch System > About phone >Authentication info to view regulatory information for yourproduct.Go to Settings and touch System > Certication logos toview more information on certication logos for your product.All pictures and illustrations in this guide, including butnot limited to the product color, size, and display content,are for your reference only. The actual product may vary.Nothing in this guide constitutes a warranty of any kind,express or implied.5

Safety InformationPlease read all of the safety information carefully before usingyour device to ensure its safe and proper operation and tolearn how to dispose of your device properly.Operation and safetyl To prevent possible hearing damage, do notlisten at high volume levels for long periods.lUsing an unapproved or incompatible power adapter,charger, or battery may damage your device, shorten itslifespan, or cause a re, explosion, or other hazards.lIdeal operating temperatures are 0 °C to 35 °C. Idealstorage temperatures are -20 °C to +45 °C.lPacemaker manufacturers recommend that a minimumdistance of 15 cm be maintained between a device and apacemaker to prevent potential interference with thepacemaker. If using a pacemaker, hold the device on theside opposite the pacemaker and do not carry the device inyour front pocket.lKeep the device and the battery away from excessive heatand direct sunlight. Do not place them on or in heatingdevices, such as microwave ovens, stoves, or radiators.lObserve local laws and regulations while using the device.To reduce the risk of accidents, do not use your wirelessdevice while driving.lWhile ying in an aircraft or immediately before boarding,only use your device according to instructions provided. Useof a wireless device in an aircraft may disrupt wirelessnetworks, present a hazard to aircraft operation, or beillegal.lTo prevent damage to your device's parts or internalcircuits, do not use it in dusty, smoky, damp, or dirtyenvironments or near magnetic elds.lWhen charging the device, make sure the power adapter isplugged into a socket near the devices and is easilyaccessible.lUnplug the charger from electrical outlets and the devicewhen not in use.lDo not use, store or transport the device where ammablesor explosives are stored (in a gas station, oil depot, or6

chemical plant, for example). Using your device in theseenvironments increases the risk of explosion or Dispose of this device, the battery, and accessoriesaccording to local regulations. They should not be disposedof in normal household waste. Improper battery use maylead to explosion, or other hazards.FCC Regulatory ComplianceBody worn operationThe device complies with RF when used nearyour ear or at a distance of 1.50 cm from your body. Ensurethat the device accessories, such as a device case and deviceholster, are not composed of metal components. Keep thedevice away from your body to meet the distance requirement. information (SAR)This device is also designed to meet the requirements forexposure to radio waves established by the FederalCommunications Commission (USA).The SAR limit adopted by the USA is 1.6 W/kg averaged overone gram of tissue. The highest SAR value reported to the FCCfor this device type complies with this limit.The highest SAR value reported to the FCC for this device typewhen using it at the ear isATU-LX3 0.49 W/kgAnd when properly worn on the body isATU-LX3 0.50 W/kgAnd when using the Wi-Fi hotspot function isATU-LX3 0.65 W/kgFCC statementThis equipment has been tested and found to comply with thelimits for a Class B digital device, pursuant to Part 15 of theFCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmfulinterference to radio communications. However, there is noguarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged totry to correct the interference by one or more of the followingmeasures:7

--Reorient or relocate the receiving antenna.--Increase the separation between the equipment and receiver.--Connect the equipment into an outlet on a circuit differentfrom that to which the receiver is connected.--Consult the dealer or an experienced radio/TV technician forhelp.This device complies with Part 15 of the FCC Rules. Operationis subject to the following two conditions: (1) this device maynot cause harmful interference, and (2) this device must acceptany interference received, including interference that maycause undesired operation.Caution: Any changes or modications to this device notexpressly approved by Huawei Technologies Co., Ltd. forcompliance could void the user's authority to operate theequipment.8

96724908_01Please visit http://consumer.huawei.com/en/support/hotline/ for recently updated hotline and email address in your country or region.Note: Remember the Google account your phone last logged in to. During an untrusted factory settings restoration or microSD card–based update, Google's anti-theft mechanism requires you to enter the Google account your phone last logged in to on the startup navigation screen for identity authentication. Your phone can properly power on only after the identity authentication passes.

Navigation menu