Huawei Technologies B660-44 Wireless Gateway User Manual II

Huawei Technologies Co.,Ltd Wireless Gateway II

Contents

User Manual II

1 B660 Quick Start Note: z The following illustrations are provided for your reference only. For details about the model you selected, please examine the actual device to determine where features are located. z Check the information about the product and its accessories when you purchase it. Some accessories are not provided in the packaging box. If required, please contact to your local dealer purchase them. z This guide briefly describes the functions of the device. For details about how to set the management parameters, see the Help on the Web management page. Getting to Know Your Device Application Scenarios Scenario 1: Your computer or a Wi-Fi device can connect to the Internet through this device. The specific connection steps depend on Wi-Fi device or your computer's operating system; please follow specific steps to commence operation.
2 (Optional) Scenario 2: You can connect a telephone set to the telephone port of the device to make voice calls. Appearance 1. Power button 2. Wi-Fi/WPS button 3. Dial-up butto 4. Wi-Fi/WPS indicator 5. Network status indicator 6. Power indicator 7. LAN indicators 8. External antenna port 9. Telephone port 10. Power port 11. LAN ports
3 Indicators Indicator Status Wi-Fi/WPS indicator z Off: Wi-Fi not activated z Steady on: Wi-Fi activated or data transfer in progress z Blinking: Establishing a WPS connection Network status indicator z Red, fast-blinking: Faulty SIM card (SIM card not inserted or malfunctioned, or PIN verification failed) z Yellow, steady on: Successfully registered to the network z Green, steady on: Connected to the Internet z Off: No signal Power indicator z Steady on: Device turned on z Off: Device turned off / / / LAN indicators z Steady on: Network cable connected z Blinking: Data transfer in progress z Off: Network cable not connected Note: z LAN indicators correspond to LAN ports. z Wi-Fi: Wireless Fidelity z WPS: Wi-Fi Protected Setup z LAN: Local Area Network
4 PC Configuration Requirements Recommended PC configurations are as follows: z CPU: Pentium 500 MHz or higher z Memory: 128 MB RAM or higher z Hard disk: 50 MB disk space available z Operating system: Windows 2000, Windows XP, Windows Vista, or Windows 7 z LCD resolution: At least 800 x 600 pixels. A resolution of 1024 x 768 pixels is recommended z Web browser: Microsoft Internet Explorer 6, Internet Explorer 7, or Internet Explorer 8, Firefox 3.5 or 3.6, Safari 3.0, Opera 10.5, or Chrome 5.1 Installation Installing the SIM Card Attention: Before inserting or removing the SIM card, please power off and unplug the device. Remove the card cover. Slide the SIM card into the card slot with the golden contact facing downward. Replace the card cover.
5 (Optional) Installing the Table Stand Your device can be placed horizontally, be placed upright with the use of a table stand, or hung on the wall. Place your device on a surface well above the floor or near a window, so it can receive a strong signal. Insert the latches on the table stand into the slots on the back of the device. The table stand allows the device to stand on a flat surface like a table or desk. See the following figures. Note: To avoid the interference caused by radio signals, place the device at least 1 meter (3.28 feet) away from other electrical devices.
6 (Optional) Installing the External Antenna Connect the external antenna to the device's external antenna port. Install the antenna securely by screwing it completely into the antenna jack. You need to first set the antenna mode to external on the management page (http://192.168.1.1). For details, see Help on the management page. Note: z If you do not need to connect an external antenna, you can skip this step. z The external antenna can be used indoor only. z While a conversation or data transfer is in progress, you are unable to switch between the internal antenna and the external antenna. (Optional) Connecting the Device to a Fixed-phone Radio signals interfere with the fixed-phone and affect the quality of the connection. Place the fixed-phone 1 meter (3.28 feet) away from the device. Note: If you do not plan to use the voice service provided by the device, skip this step.
7 Connecting the Device to a PC Using an Ethernet Cable If the indicator for the LAN port to which the Ethernet cable is connected is on, the connection is active. The network cable connecting to the PC must not be longer than 100 meters (328 feet). Connecting the Power Supply Attention: Use a power adapter that is compatible with the device or else the device may be damaged. Powering On/Off the Device z After connecting the power supply, the device will power on automatically. z Press and hold until all indicators turn off to power off the device. z Press and hold until all indicators turn on to power on the device
8 Setting Up Wireless Connection Step 1. Activating Wi-Fi z After the device is powered on, Wi-Fi is activated by default. z Press and hold for 2 seconds, and then stop the press. Then, is off, which indicates that Wi-Fi is deactivated. z Press and hold until is steady on to activate Wi-Fi. Step 2. Establishing a Wi-Fi Connection Establishing a Wi-Fi Connection (Using a PC as an Example) Note: Before establishing a Wi-Fi connection, you must ensure that your computer is equipped with a wireless network adapter. If it is clear that the computer has a wireless network connection, then the wireless network adapter can be used. Otherwise, you must ensure that the wireless network adapter is functioning properly. 1. Make sure that is steady on. 2. View available wireless network connections on your PC. 3. Connect to the wireless network connection consistent with your device's SSID. Note: z If the wireless network has security mechanism, you must enter the correct network key. z The SSID and password are printed on the device label.
9 (Optional) Establishing a WPS Connection If the Wi-Fi device to which your device connects supports WPS, a password is generated automatically. To set up the WPS connection, do as follows: 1. Make sure that is steady on. 2. Activate WPS on your device. Note: Press and hold until is blinking to activate WPS. 3. Activate WPS on the client. Note: For details about operations on the client, see the user guide of the client. Using the Management Page You can set and manage the device parameters through the management page. 1. Launch a web browser and enter http://192.168.1.1 in the address bar. 2. Enter the password and click Login. Note: z The default password is admin. z To protect your device, only allow one user to log in to the management page at the same time.
10 Accessing the Internet After a connection between your device and the client is active, you use the following modes to access the Internet. Attention: Please select a proper Internet connection mode according to your network charges. For example, if you are using time-based service, Manual mode is recommended. Please consult your network operator for network charges. Mode Operation Auto After the device is powered up, no matter if there is data transmission or not, it will be connected to the Internet, and won't disconnect automatically. Manual z Press and hold until is steady on in green. The Internet connection is active. z After you are logged in to the management page, you can connect or disconnect using your interface prompt. On Demand After the device is powered up, and there is data transmission, it will automatically connect to the Internet. If there is no data transmission within the set time, the device will automatically disconnect from the Internet.
11 Restoring Factory Defaults If you become uncertain of which parameters you have set or changed, you can restore the factory defaults which the device came with and set the parameters again. RESET: Use a sharply pointed object to press and hold the RESET button until all five indicators ( ,,, and ) are blinking. The device will automatically restart after the factory defaults are successfully restored. Note: Restoring factory defaults removes all personal configurations and resets all configurations on the management page to their default values. Friendly Tips If you are unable to use your device normally, do as follows: z See Help on the management page. z Restart the device. z Restore the device to factory defaults. z Contact your service provider.
12 Copyright © Huawei Technologies Co., Ltd. 2011. All rights reserved. THIS DOCUMENT IS FOR INFORMATION PURPOSE ONLY, AND DOES NOT CONSTITUTE ANY KIND OF WARRANTIES. Version: V100R001_02 Part Number: 96720304

Navigation menu