Huawei Technologies B970 Wireless Gateway User Manual E960B970 Series
Huawei Technologies Co.,Ltd Wireless Gateway E960B970 Series
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 970649 |
| Application ID | 4yUKnPdKGgpVt9lDTVOkRA== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 108.98kB (1362282 bits) |
| Date Submitted | 2008-07-15 00:00:00 |
| Date Available | 2008-07-15 00:00:00 |
| Creation Date | 2008-04-28 11:52:53 |
| Producing Software | Acrobat Distiller 7.0 (Windows) |
| Document Lastmod | 2008-06-12 11:46:43 |
| Document Title | E960B970 Series.book |
| Document Creator | FrameMaker 7.1 |
| Document Author: | m00114311 |
Wonderful Communication, Mobile Life. Welcome to 3G Wireless Gateway HUAWEI 3G Wireless Gateway User Guide Notice Copyright © 2008 Huawei Technologies Co., Ltd. ual do not constitute the warranty of any kind, expressed or implied. Huawei Technologies Co., Ltd. All Rights Reserved 1 No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and HUAWEI are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this manual are the property of their respective holders. Notice 5 The information in this manual is subject to change without notice. Every effort has been made in the preparation of this manual to ensure accuracy of the contents, but all statements, information, and recommendations in this man- Address: 6 Administration Building, Huawei Technologies Co., Ltd., Bantian, Longgang District, Shenzhen, P. R. China Postal Code: 518129 Website: http://www.huawei.com Safety Precautions Read the safety precautions carefully to ensure the correct and safe use of your wireless device. For detailed information, see "Warnings and Precautions." Do not switch on your device when the device use is prohibited or when the device use may cause interference or danger. Do not use your device while driving. Follow the rules or regulations in hospitals and health care facilities. Switch off your device near medical apparatus. Switch off your device in an aircraft. The device may cause interference to control signals of the aircraft. Switch off your device near high-precision electronic devices. The device may affect the performance of these devices. Do not attempt to disassemble your device or its accessories. Only qualified personnel are allowed to service or repair the device. Do not place your device or its accessories in containers with strong electromagnetic field. Do not place magnetic storage media near your device. Radiation from the device may erase the information stored on them. Do not put your device in a hightemperature place or use it in a place with flammable gas such as a gas station. Keep your device and its accessories away from children. Do not allow children to use your device without guidance. Use approved accessories only to avoid explosion. Observe the laws or regulations on device use. Respect others’ privacy and legal rights when using your device. Table of Contents Table of Contents 1 Using the Management Page 1 Log in to the Management Page ................1 Management Page Overview .....................1 View Configuration Information ..................2 Quick Setup................................................2 Accessing the Internet................................4 Configuring Your Computer 6 Wireless Configuration ...............................6 Configuring the PC Network.......................7 Advanced Settings 8 Overview ....................................................8 System Management .................................8 SIM/UIM Settings .......................................9 Mobile Network Settings...........................10 Dial-up Settings ........................................11 DHCP Settings ........................................12 WLAN Settings .........................................13 Safety Information 25 Interference.............................................. 25 Medical Device......................................... 25 Area with Inflammables and Explosives . 25 Traffic Security ......................................... 25 Safety of Children .................................... 26 Environment Protection............................ 26 WEEE Approval ....................................... 26 RoHS Approval ........................................ 26 Laws and Regulations bservance ............ 26 Care and Maintenance............................. 26 Emergency Call........................................ 27 Specific Absorption Rate (SAR)............... 27 Body Worn Operation .............................. 27 Regulatory Information............................. 27 Abbreviations 29 Security Settings (Optional) 17 Firewall Switch .........................................17 LAN MAC Filter ........................................17 LAN IP Filter .............................................17 Virtual Server............................................18 DMZ Settings............................................20 UPnP Settings ..........................................20 Remote Management...............................20 Troubleshooting 22 1 Using the Management Page Log in to the Management Page Start the Internet browser and enter the address http://192.168.1.1 in the address bar. Select a user type, enter the password, and then click Login. • Admin: This user type is authorized to view and change the configurations. The default password is admin. • User: This user type is authorized to view only the basic status information. The default password is user. Note To avoid the configuration conflict, only one user is allowed to log in to the management page at a time. Item Description Basic Status Displays the parameter configuration status of the device. Quick Setup Quickly configures the device. Connection Displays the network connection status and connects to the network. Advanced Settings Configures the advanced settings. Security (Optional) Configures the security settings. Logout Log out of the management page. Device Status The following table shows the status information of the device. Item Green icon The card is valid. The card is not inserted or is invalid. WAN The PPP dial-up connection is established. The PPP dial-up connection is not established. Management Page Overview Operation Functions The following table shows the main operations in the management page. Red icon SIM/UIM View Configuration Information Item WCDMA Green icon Red icon The WCDMA The WCDMA network network is available. is unavailable. Note If the device is registered with other network modes, the corresponding network connection status is displayed. SIG The signal strength from weak to strong is shown as follows: View Configuration Information On the configuration page, you can view the current parameter configuration information and the network connection status. Click Basic Status. Click Advanced on the right part of the page to view the advanced status. Quick Setup You can use the quick setup wizard to configure and maintain the basic parameters of the device. Click Quick Setup to access the welcome page. Click Next to configure the PPP profile settings. Configuring PPP Profile Settings • Profile Name: Enter a profile name when the text box is empty. • Dial-up Number/PPP User Name/PPP Password: Enter these three parameters provided by the internet service provider (ISP). The dial-up number is used to initiate the network call; the PPP user name and PPP password is used to obtain the service authorization provided by the ISP. • APN/IP Address: Select the mode for obtaining the access point name (APN) and IP address. If the carrier provides the relevant parameters, select Static and enter their values. Otherwise, select Dynamic and the device automatically obtains them. Configuring PPP Dial-up Settings Click Refresh to view the current status on the advanced status page. PPP Connection: Select the dial-up access mode. • Auto: The device automatically connects to the Internet and does not disconnect when no data is transmitted. Quick Setup PPP Authentication: This service is provided by your ISP. For details, consult your ISP. obtain the SSID of the WLAN. In this case, the WLAN security is improved. Note For the convenience of users accessing the WLAN, you can select Enabled for SSID Broadcast when you configure the WLAN setting. After the setting, you can select Disable to improve the WLAN security. Configuring the WLAN Encryption Configuring WLAN Settings (Name) SSID: Enter a name for your wireless local area network (WLAN). • The service set identifier (SSID) is used to identify a WLAN. A PC and the wireless device can perform normal data communication only when they have the same SSIDs. To ensure the WLAN security, do not use the default SSID. You can enter a character string as the SSID, such as MyHome. SSID Broadcast: Enable or disable the SSID broadcast. • Enabled: The device broadcasts the SSID of the WLAN and users can easily access the WLAN. In this case, unauthorized users can also access the WLAN because the SSID is broadcasted. • Disabled: The device does not broadcast the SSID of the WLAN. Before accessing the WLAN, a user must To access the WLAN, you must set the wireless security key on your PC to be the same as that of the wireless device. No Encryption Using the Management Page • On Demand: The device automatically connects to the Internet when data transmission exists. When the duration of no data transmission exceeds the maximum idle time, the device disconnects the Internet connection. • Manual: The device connects to the Internet after you click Connect on the connection page. For details, see "Accessing the Internet." • For the convenience of users accessing the WLAN, you can select NO ENCRYPTION for the Encryption mode when you set up a WLAN. It is not recommended to select this option in daily use. WPA-PSK/WPA2-PSK • WPA-PSK: It is a 256-bit data encryption method that can automatically change the key. • WPA2-PSK: It is a more secure version of WPA-PSK and it supports the IEEE 802.11 standard. • WPA Encryption Algorithm: TKIP, AES, TKIP+AES. • WPA Pre-Shared Key: You can enter a 64-character hexadecimal value or 8-63-character ASCII value as Accessing the Internet the key. The ASCII value contains all characters that can be entered through the PC keyboard, and the hexadecimal value contains numbers of 0-9 and characters of A-F. For example, you can enter the ASCII value of 1234abcde as the key. • Network Key Rotation Interval: It is used to set how long a network key is dynamically changed. By default, it is 0. To disable this function, you can set the value to 0 or null. Accessing the Internet Note • If you are required to enter the PIN code, enter the correct one. If you fail to enter the correct PIN or PUK code, the network-related functions are unavailable. • The SIM/UIM card is supplied by the service provider. For details, contact your service provider. WEP • Wireless Equivalent Privacy (WEP) is a 64-bit or 128-bit data encryption method. The 128-bit WEP encryption provides higher security level. • Network key 1: You can enter 5 ASCII characters or 10-character hexadecimal numeral to form a 64-bit key. You can also enter 13 ASCII characters or 26-character hexadecimal numeral to form a 128-bit key. • When the Save PIN Code check box is selected, the Auto validation of PIN code is enabled. • If Auto validation of PIN code is enabled, the PIN code is recorded and automatically validated after each reboot. Validating Quick Setup The last page of the wizard displays all the settings you have configured. • To accept the settings, click Finish. • To change the settings, click Back. • To quit the settings, click Cancel. Click Connection. If PPP Connection is Auto or On Demand, refresh the page to view the current network connection status. Accessing the Internet If PPP Connection is Manual, click Connect / Disconnect to connect to or disconnect from the network. Wait for several minutes, if you are prompted that the connection is successful, you can start the browser and enter the website address to access the Internet. Using the Management Page 2 Configuring Your Computer This takes the Windows XP operating system (OS) as an example to describe how to configure your computer. For other OSs, the configurations may be different and you need to configure them as required. • For SSID parameters configuration, see "Configuring WLAN Settings." Configuring the Wireless Network Choose Start > Control Panel > Network Connections > Wireless Network Connection. Click Show Wireless Networks to display the wireless network connection list. Select the network connection that the SSID is the same as that of the device, and then click Connect. If the encryption parameter is set for the device, the Wireless Network Connection dialog box is displayed and requires the network key and confirmation. The value you entered must be the same as the WPA Pre-Shared Key or Network Key of the device. Wireless Configuration The wireless configuration allows your PC to connect to the device through the wireless network. If you need only the Ethernet to connect your PC, you can skip this part. Configuration Requirements • To set up wireless network connection, your PC must be configured with the WLAN adapter that supports the IEEE 802.11 b/g protocol. • If the encryption function is enabled, you need to ensure that all PCs connecting to the device use the same key as that of the device. • For the use of WLAN adapter, refer to the WLAN adapter user guide provided by the manufacturer. • For the encryption configurations, see "Configuring the WLAN Encryption Mode." Configuring the PC Network Wait for a while after you enter the correct network key. The wireless connection icon displays in the status area in the lower right corner of the screen. Then, your PC can automatically connect to the device. In the Local Area Connection Properties dialog box, select Internet Protocol (TCP/IP) in the This connection uses the following items list box, and then click Properties. In the Internet Protocol (TCP/IP) Properties dialog box, select Obtain an IP address automatically and Obtain DNS server address automatically, and then click OK. Configuring the PC Network The recommended configurations of the PC are as follows: Disabling Proxy Settings • Obtain an IP address automatically. Confige the Network Connection Start the Internet browser, and then choose Tools > Internet Options. Choose My Network Places > Properties > Local Area Connection. Select the Connections tab, and then click LAN Settings. Right-click the Local Area Connection icon and select Properties. In the LAN Settings dialog box, deselect Use a proxy server for your LAN. Configuring Your Computer • Deselect Use a proxy server for your LAN. 3 Advanced Settings Overview System Management Click Advanced Settings, you can configure both the basic attributes and advanced parameters of the device, and also perform routine maintenance and management to the device. The following table shows the functions of the shortcut icons. Icon Description to access the System page. Changing the Password You can change the login password to prevent unauthorized users from logging in to the management page. Click to access the System page. Click Click to access the SIM/UIM Settings page. Enter the current password, and then enter the new password and confirm it.. Click Modify. Click to access the Mobile Network Settings page. Click to access the Dial-up Settings page. Click to access the DHCP Settings page. Click to access the WLAN Settings page. Click Upgrading the device Click Enter the path or click Browse to select the software image file to be updated. SIM/UIM Settings Click Upgrade. • After the system is upgraded, the system automatically restarts. The whole process takes two to three minutes. Warning • The software programs for upgrading must come from the official website of Huawei or the official website of the carrier. • Upgrading the software does not change the configuration of the client. Restoring the Factory Defaults Click to access the Restore Defaults page, and then click Restore. this operation, all configurations are Note After restored to the defaults. Click Click Reboot. to access the Reboot page. Viewing the Version Information Click to access the Version page. You can view the hardware version, software version, and the release time. SIM/UIM Settings Click to access the SIM/UIM Settings page. Advanced Settings If you need to reconstruct the network or you forget the changes of some parameters, you can choose to restore factory defaults and reconfigure the device. Restarting the Device When the device works in the ROM-SIM mode, the page is not available. Enabling or Disabling the PIN Code Click Mobile Network Settings Select Enable/Disable in the PIN Code Operation list box. Enter the correct PIN code. Click Apply. Auto Validating PIN Code You can enable or disable the auto validate PIN code function. Click Changing the PIN Code Select Enable/Disable in the Auto Validate option button. When the PIN code protection is enabled, you can reset the PIN code. Enter the current PIN code. Click Apply. Click Select Modify in the PIN Code Operation list box. Enter the current PIN code. Enter the new PIN code and confirm it. Click Apply. Mobile Network Settings Click page. to access the Mobile Network Settings Setting the Preferred Mode and Band 10 Click Dial-up Settings Select the preference of connection mode in the Preferred Mode list box. • Auto: The device automatically searches the network and registers with it. • Manual: You need to manually search the network and register with it. the carrier provides only the 2G Note • Ifservice and the preferred mode is configured as 3G only, you cannot access the Internet. • If the carrier provides only the 3G service and the preferred mode is configured as 2G only, you cannot access the Internet. Select the band to search the network in the Band list box. Click Apply. Configuring the Mode for Searching Network Click Click Apply. In Manual mode, select the searched network and click Log on. Dial-up Settings Click to access the Dial-up Settings page. Configuring the PPP Settings Click Enter the correct parameters. Advanced Settings • If the carrier provides neither the 3G nor 2G service, you cannot access the Internet regardless of the preferred mode. Select the mode for searching the network. to access the PPP Settings page • Profile List: Select a profile from the established dial-up connection list. If the drop-down list is empty, you need to create a profile list. 11 DHCP Settings • PPP Connection: Select the dial-up connection mode. • PPP Authentication: The service is provided by your ISP. For details, consult your ISP. • PPP Max Idle Time: The duration of the PPP connection is in idle. In On Demand mode, if no data is transmitted in this duration, the PPP connection automatically disconnects. • PPP MTU: It is the maximum transmission unit (MTU) of the PPP connection. It is used to set the maximum number of bytes encapsulated in a single data frame. • PPP Max Dial Time: Set the maximum waiting time when connecting to the Internet. Managing the Profile List Click to access the Profile Settings page. ◆ Changing a Profile Select a profile to be changed in the Profile List drop-down list. Relevant information is displayed in the corresponding text box. Enter the profile information. Click Save. ◆ Deleting a Profile Select a profile to be deleted in the Profile List drop-down list. Click Delete. DHCP Settings ◆ Creating a Profile 12 Enter the profile information in the text box according to the prompts. Click Save. Click to access the DHCP Settings page, you can set the mode for assigning IP addresses in a LAN. DHCP automatically assigns IP addresses to the network devices. If you are using the DHCP server, you need to do the configurations on the PC WLAN Settings connecting with the device. For details, see "Configuring the Network Connection". Start IP Address must be smaller than Note • The or equal to the End IP Address. • IP Address: The default IP address of the device is 192.168.1.1. • If the DHCP Server is Enabled, the configurations of Start IP Address, End IP address, and DHCP Lease Time are valid; otherwise, you cannot configure them. • Subnet Mask: The combination of the subnet mask and IP address enables the flexible sub netting. By default, the subnet mask is 255.255.255.0. • DHCP Server: It is used to assign IP addresses dynamically. If the DHCP server is Enabled, it can automatically assign IP addresses for PCs. It is recommended to select Enabled for the DHCP server. • DHCP Lease Time: The DHCP server automatically assigns an IP address to each device connected to the network. When the leased time expires, the DHCP server checks whether the device is connected to the network. If the device is disconnected from the network, the server assigns the IP address to another device. Thus, the IP address is not wasted. Click to access the WLAN Settings page. Enabling or Disabling the WLAN Click Select Enable/Disable to enable or disable the WLAN. Click Apply. to access the WLAN Enable page. Advanced Settings • Start IP Address/End IP Address: It is used to define the IP address range that the host can use during the IP address assignment. For example, in the network segment 192.168.1.0/24, the default IP address of the device is 192.168.1.1. The host IP address can range from 192.168.1.2 to 192.168.1.254. The minimum range is a single IP address. WLAN Settings 13 WLAN Settings WLAN Basic Settings Click page. to access the WLAN Basic Settings Selecting Interface IDs • Wireless Interface: It refers to the SSID and MAC address, and is used to identify the wireless device. SSID • Entering a name (SSID) for your WLAN. • Enabling or Disabling the SSID Broadcast. Enabling or Disabling the AP Isolation • Channel: It refers to the channel that the device works with. If you do not know which channel to select, select Auto and the device can automatically search for the channel. Configuring the 802.11 Mode There are four available modes, as shown in the following table. Mode 54g Auto 54g The WLAN has the best performance Performance in this mode. 54g LRS • On: The terminals (PCs) connecting to the device through the WLAN cannot communicate with each other. • Off: The terminals (PCs) connecting to the device through the WLAN can communicate with each other. Selecting a Country • Country: It is used to identify the country. Different countries have different standards on channel usage. Selecting a WLAN Channel 14 Description The WLAN has the best compatibility in this mode. If the device has difficulties in communicating with devices conforming to the IEEE 802.11b standards, select this mode. 802.11b Only The device can only work in the low performance 802.11b standard network mode. 54g Only The device can only work in the low performance 802.11g standard network mode. WLAN Settings Configuring the Transmission Rate Select Auto, the device automatically searches the transmission rate. Click Apply to submit the setting. WLAN Advance Settings Click page. • There are four encryption modes: No Encryption, WPAPSK, WPA2-PSK, and WEP. For details, refer to "Configuring the WLAN Encryption Mode." Configuring the MAC Filter Click to access the WLAN MAC Filter page.You can control and manage the clients accessing the WLAN, and improve the WLAN security performance. to access the WLAN Advance Settings MAC Restrict Mode The following table shows the MAC address filter modes: Configuring the 802.11 Authentication Disabled The MAC address filter function is disabled. Allow The clients with addresses in the MAC Address list are allowed to connect with the device through the WLAN. Deny The clients with addresses in the MAC Address list are not allowed to connect with the device through the WLAN. • Open: Open system authentication. A user accessing the WLAN can choose WEP, WPA-PSK, or WPA2-PSK key to pass the authentication or choose No encryption to skip the authentication. • Shared: Shared key authentication. It can use only WEP. The user accessing the WLAN must use the WEP to authenticate. Configuring the Encryption Mode Parameter Description Advanced Settings A security key can protect your WLAN from illegal data attacking. The security key of your wireless device must be consistent with that of the PC. 15 WLAN Settings MAC Addresses Mode • Enter MAC addresses in the list. The device can perform the access control over the clients whose MAC addresses are in the list. WLAN Bridge Click to access the WLAN Bridge page. • Preamble Type: It has two options: Long and Short. In the case that the client (PC) supports the Short type, the WLAN can have a better performance if it is Short. • MAX Associations Limit: It refers to the maximum number of connections. It is used to set the maximum number of concurrent WLAN users on the device. • Mode: It refers to the WLAN accessing mode. The device can work in two modes, as shown in the following table. The default value is Access Point. Mode Description Wireless It is used to connect two or more access Bridge points. 16 Access Point Description The access points meeting the IEEE 802.11b/g standard or the wireless terminals can connect the wireless device. • Bridge Restriction: It refers to the limitation to the peer MAC addresses. When it is Disabled, the device can access all the remote bridges; when it is Enabled, the device can only access the remote bridges that the addresses are in the address list. • Bridges: It refers to the physical address of the remote peer bridge. The device supports the point-to-multipoint (PTM) bridge mode. • Peer MAC Address: It refers to the physical address list of the remote peer bridges.. • Link Status: Up shows the successful connection and Down shows the failed connection. 4 Security Settings (Optional) Click Security, you can configure the advanced security settings. Firewall Switch Your device has a true firewall that controls the incoming and outgoing data flow and protects your computer from illegal intrusion. Click Select the Enable the firewall (main switch of the firewall) check box to enable the firewall. Note • Only when the Enable the firewall check box is selected, the other functions such as the IP address filter function, the MAC address filter function, and the WAN port ping function are available. • When the Enable LAN MAC address filter check box is selected, the default filter rules are available. Select other options as required, and then click Apply. LAN MAC Filter Your device supports MAC filtering based on a list of either denied or allowed computers. A common method to restrict network access is to specify the Media Access Control (MAC) address. To locate the MAC address in the Windows OS, choose Start > Run, and then enter cmd. The command window is displayed, enter ipconfig / all, and then press Enter. The MAC address is displayed as the Physical Address. Click Select MAC Filter Mode. Enter the MAC addresses of the clients and click Apply. LAN IP Filter You can configure the device to block specific IP address so that they cannot be accessed from 17 Virtual Server computers in the local network. Deleting an IP Address Click Click to access the LAN IP Filter page. Adding an IP Address in the Modification column. The corresponding IP address filter is deleted. Validating an IP Filter Select the protocol and status. Enter the IP address and corresponding port to be blocked from accessing the LAN. Click Ok. Changing an IP Address Click in the Modification column. The corresponding IP address filter is displayed. Change the contents as required. Click Ok. Add a new IP address or select a record in the IP address filter table. Select On for Status. Click Ok. Click Apply. Virtual Server Your device supports the virtual server to enable external computers to access WWW, FTP, or other services provided by the LAN. Click 18 to access the Virtual Server page. Virtual Server Adding a Virtual Server Select the protocol and status. Changing a Virtual Server Enter values in the following text boxes: Click in the Modification column. The relevant virtual server is displayed. • WAN Port: Enter the WAN port of the LAN in which the computer provides services. Change the contents as required. • IP Address: Specify a computer in the LAN to provide services. Click Ok. • LAN Port: Enter the LAN port of the computer that provides services. Click Ok. You can also add a virtual server in the following way: Select a port from the Common Port list. The Protocol, Status, Name, WAN Port, and LAN Port will be set as the default values. If required, you can change them. Deleting a Virtual Server Security Settings (Optional) • Name: Enter a name to the service provided by the LAN. Click Ok. Click in the Modification column. The corresponding virtual server is deleted. Validating a Virtual Server Add a virtual server or select a record in the virtual server table. Select On for Status. Click Ok. Enter the IP Address. 19 DMZ Settings Click Apply. Note Only one computer can be specified as a DMZ host at a time. DMZ Settings If your PC cannot run network applications through the device, you can set the computer to access the Internet unlimitedly by configuring the IP address of the computer in the demilitarized zone (DMZ). However, the DMZ computer is not protected by the firewall. It is vulnerable to attack and may also put other computers in the home network at risk. Click Select Enabled /Disabled for DMZ Status to enable or disable the DMZ service. Enter the local IP address of the computer that is specified as a DMZ host. Click Apply. UPnP Settings The Universal Plug and Play (UPnP) service allows other network users to control your device’ s network features to realize the intelligent interconnection. Click Select Enabled/Disabled for UPnP Status to enable or disable the UPnP service Click Apply. Remote Management The remote web management allows the access and control of the device either from the home network or from the Internet. When you are on a trip, you can maintain your device through the remote web management service. It also 20 Remote Management allows your ISP to help you solve the device problems from a remote location. Click Select Enabled /Disabled for Remote Status to enable or disable the service. Enter the IP address that can access and control your device. Click Apply. Security Settings (Optional) 21 5 Troubleshooting are correct, and see "Configuring PPP Profile Settings" for details. What to do if a PC in the LAN cannot access the Internet? If the power indicator is off, you need to check whether the power adapter is normally connected. If the signal strength indicator is off, you need to check whether the area is covered by the network. 22 If the area is covered by the network, you need to check whether the network mode is correct. For information about network mode, see "Mobile Network Settings". If the indicator of the Ethernet interfaces blinks, the corresponding Ethernet interface is normally connected. If the indicator is off, you need to check and ensure that the related Ethernet connection is normal. You must configure the correct PPP user name and PPP password when you access the Internet through the device. Check whether they If the DHCP service is disabled and the PC obtains the IP address dynamically, the PC also cannot access the Internet. You can change the mode to manually assign an IP address. See "Configuring the Network Connection". Check whether the driver of the network adapter is correctly installed. If the preceding methods cannot solve the problem, please consult you service provider. What to do if a PC in the WLAN cannot access the WLAN? If interferences or shields near the device exist, you can adjust the position of the device. When the signal strength is strong, you can move to the next step. Check and record the following data on the network adapter of your PC: SSID, WEP type, and key. Make sure that the two devices work on the same channel. For details, see "Selecting a WLAN Channel". Check and record the following data on the device: SSID, WEP type, and key. Make sure that the MAC address of one device is in the peer MAC address list of the other device. For details, see "WLAN Bridge". Compare the recorded data, the SSID on the network adapter should be ANY or be the same as that on the device. The WEP type and key on the network adapter and device should be the same. Otherwise, you need to change the data on the network adapter. What to do if I forgot the IP address of the LAN interface? If you forgot the IP address of the LAN interface, you can enter http://e.home and log in to the management page when the PC obtains the IP address automatically. What to do if bridging between two devices is unsuccessful? When the signal strength is normal, what to do if the downloading rate is low? Troubleshooting In this case, you need to set the value in the registry as follows: Choose Start > Run. Enter regedit in the Open text box and then click OK. Select parameters in the following directory: \HKEY_LOCAL_MACHINE\SYSTEM\CurrentC ontrolSet\Services\Tcpip. Choose Edit > New > DWORD Value. Rename New Value #1 to TcpWindowSize. 23 24 Right-click TcpWindowSize and then select Modify. Select Decimal and enter 65535 in the Value data text box, and then click OK. For the DWORD Value of DefaultRcvWindow, do the same operations as that of TcpWindowSize. 6 Safety Information Read the safety information carefully to ensure the correct and safe use of your wireless device. Interference Do not use your wireless device if using the device is prohibited or when it cause danger or interference with electric devices. Medical Device • Do not use your wireless device and follow the rules and regulations set forth by the hospitals and health care facilities. • Some wireless devices may affect the performance of the hearing aids. For any such problems, consult your service provider. • If you are using an electronic medical device, consult the doctor or device manufacturer to confirm whether the radio wave affects the operation of this device. Area with Inflammables and Explosives To prevent explosions and fires in areas that are stored with inflammable and explosive devices, do not use your wireless device and observe the rules. Areas stored with inflammables and explosives include but are not limited to the following: • Gas station • Fuel depot (such as the bunk below the deck of a ship) • Container/Vehicle for storing or transporting fuels or chemical products • Area where the air contains chemical substances and particles (such as granule, dust, or metal powder) • Area indicated with the "Explosives" sign • Area indicated with the "Power off bi-direction wireless equipment" sign • Area where you are generally suggested to stop the engine of a vehicle Traffic Security • Observe local laws and regulations while using the wireless device. To prevent accidents, do not use your wireless device while driving. • RF signals may affect electronic systems of motor vehicles. For more information, consult the vehicle manufacturer. • In a motor vehicle, do not place the wireless device over the air bag or in the air bag deployment area. Otherwise, the wireless device may hurt you owing to the strong force when the air bag inflates. 25 Safety of Children • Observe the rules and regulations of airline companies. When boarding, switch off your wireless device. Otherwise, the radio signal of the wireless device may interfere with the plane control signals. Safety of Children Do not allow children to use the wireless device without guidance. Small and sharp components of the wireless device may cause danger to children or cause suffocation if children swallow the components. Environment Protection Observe the local regulations regarding the disposal of your packaging materials, used wireless device and accessories, and promote their recycling. WEEE Approval The wireless device is in compliance with the essential requirements and other relevant provisions of the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE Directive). 26 RoHS Approval The wireless device is in compliance with the restriction of the use of certain hazardous substances in electrical and electronic equipment Directive 2002/ 95/EC (RoHS Directive). Laws and Regulations bservance Observe laws and regulations when using your wireless device. Respect the privacy and legal rights of the others. Care and Maintenance It is normal that your wireless device gets hot when you use or charge it. Before you clean or maintain the wireless device, stop all applications and disconnect the wireless device from your PC. • Use your wireless device and accessories with care and in clean environment. Keep the wireless device from a fire or a lit cigarette. • Protect your wireless device and accessories from water and vapor and keep them dry. • Do not drop, throw or bend your wireless device. • Clean your wireless device with a piece of damp and soft antistatic cloth. Do not use any chemical agents Emergency Call Emergency Call This wireless device functions through receiving and transmitting radio signals. Therefore, the connection cannot be guaranteed in all conditions. In an emergency, you should not rely solely on the wireless device for essential communications. Specific Absorption Rate (SAR) Your wireless device is a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves recommended by international guidelines. These guidelines were developed by the independent scientific organization ICNIRP and include safety margins designed to assure the protection of all persons, regardless of age and health. The guidelines use a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit for wireless devices is 2.0 W/kg and the highest SAR value for this device when tested complied with this limit. Body Worn Operation Important safety information regarding radiofrequency radiation (RF) exposure. To ensure compliance with RF exposure guidelines the device must be used with a minimum of 1.5 cm separation from the body. Failure to observe these instructions could result in your RF exposure exceeding the relevant guideline limits. Safety Information (such as alcohol and benzene), chemical detergent, or powder to clean it. • Do not leave your wireless device and accessories in a place with a considerably low or high temperature. • Use only accessories of the wireless device approved by the manufacture. Contact the authorized service center for any abnormity of the wireless device or accessories. • Do not dismantle the wireless device or accessories. Otherwise, the wireless device and accessories are not covered by the warranty. Regulatory Information The following approvals and notices apply in specific regions as noted. CE Approval (European Union) The wireless device is approved to be used in the member states of the EU. The wireless device is in compliance with the essential requirements and other 27 Regulatory Information relevant provisions of the Radio and Telecommunications Terminal Equipment Directive 1999/5/EC (R&TTE Directive). CE Statement: The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons. Federal Communications Commission Notice (United States): Before a wireless device model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government-adopted requirement for safe exposure. The SAR limit adopted by the USA and Canada is 1.6 watts/kilogram (W/kg) averaged over one gram of tissue. The highest SAR value reported to the FCC for this device type was compliant with this limit. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. * This device should be installed and operated with a minimum distance of 20 cm between the radiator and your body when using it via USB cable. 28 This equipment has been tested and found to comply with the limits for a Class B digital Device, pursuant to Part 15 of the FCC rules Changes or modifications made to this equipment not expressly approved by (manufacturer name) may void the FCC authorization to operate this equipment. 7 Abbreviations 3G The Third Generation WLAN AP Access Point WCDMA Wideband CDMA APN Access Point Name WI-FI Wireless Fidelity CDMA Code Division Multiple Access DHCP Dynamic Host Configuration Protocol DNS Domain Name Server EDGE Enhanced Data rates for GSM Evolution GSM Global System for Mobile communications GPRS General Packet Radio Service HSPA High Speed Packet Access HSDPA High Speed Downlink Packet Access HSUPA High Speed Uplink Packet Access IP Internet Protocol LAN Local Area Network LED Light Emitting Diode NAT Network Address Translation POTS Plain Old Telephone Service UMTS Universal Mobile Telecommunications System WAN Wide Area Network Wireless Local Area Network 29
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Encryption : Standard V2.3 (128-bit) User Access : Print, Extract, Print high-res Page Count : 33 Page Mode : UseOutlines Has XFA : No XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:352637ef-72c9-48e1-af28-c8384565825f Producer : Acrobat Distiller 7.0 (Windows) Creator Tool : FrameMaker 7.1 Modify Date : 2008:06:12 11:46:43+08:00 Create Date : 2008:04:28 11:52:53Z Metadata Date : 2008:06:12 11:46:43+08:00 Document ID : uuid:f1992e9c-c369-4617-9e35-31829ac2b1f4 Instance ID : uuid:b904aefa-2edc-42de-b80e-35c797050502 Format : application/pdf Title : E960B970 Series.book Creator : m00114311 Author : m00114311EXIF Metadata provided by EXIF.tools