Huawei Technologies E226 HSDPA USB Modem User Manual

Huawei Technologies Co.,Ltd HSDPA USB Modem

a href="https://usermanual.wiki/Huawei-Technologies" itemprop="url"> Huawei Technologies >

User Manual

Copyright © 2007 Huawei Technologies Co., Ltd. All Rights Reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and HUAWEI are trademarks of Huawei Technologies Co., Ltd. All other trademarks mentioned in this manual are the property of their respective holders. Notice The information in this manual is subject to change without notice. Every effort has been made in the preparation of this manual to ensure accuracy of the contents, but all statements, information, and recommendations in this manual do not constitute the warranty of any kind, expressed or implied. i Table of Contents Getting Started .........................................................................................................1 Preparing E226 ........................................................................................................2 Installation Instructions ...........................................................................................2 Safety Information...................................................................................................5
1 Thank you for choosing E226 HSDPA USB Modem (hereinafter referred to as the E226) from Huawei. Note: This manual briefs the profile of the E226, and the preparation, and installation process. For the operation of the management program, see User Manual.. Getting Started 1. Getting to Know the E226 The following figure shows the E226 profile. USB interfaceUSIM/SIM card slot Indicator 2. Indicator This indicator indicates the status of E226. y Off: The E226 is powered off. y Green, Blinking twice every 2.7 seconds: The E226 is searching for a network or no network is available. y Green, Blinking twice every 2.9 seconds: The GSM network is normal. y Blue, Blinking once every 2.9 seconds: The WCDMA network is normal. y Green: GPRS data service is established. y Cyan: HSDPA data service is established. y Blue: WCDMA data service is established. 3. Computer Configuration Requirements To use the E226, configure a computer according to the following items: y Central processing unit (CPU): Pentium 4, 1 GHz or above y Memory: 128 MB RAM or above y Hard disk: 50 MB or above y Operating system (OS): Windows XP, Windows 2000, or Windows Vista y Universal serial bus (USB) modem interface: USB 2.0 full speed y Display resolution: 800 % 600 or above (1024 % 768 is recommended) Note: y Improper configuration may degrade the computer performance. 2 y For Windows XP, it is recommended to install patches such as Service Pack 2 or above. y For Windows 2000, it is recommended to install patches such as Service Pack 4 or above. Preparing E226 1) Remove the UMTS subscriber identity module/subscriber identity module (USIM/SIM) card slot from the E226. Then insert the USIM/SIM card into the card slot, as shown in the following figure. Make sure that the USIM/SIM card is fully in place. 2) Insert the card slot into the E226, as shown in the following figure. Installation Instructions The installation procedures of the E226 Manager vary with operating systems (OSs). Refer to the actual installation instructions during the installation process. 1. Connecting the E226 with a Computer Note: First, power on a computer. Then connect the E226 with the computer. Otherwise, the normal installation of the E226 can be affected. The following figure is the sketch map of the data cable. Auxiliary USBdata cableMini-USBConnectorMini-USBdata cable
3 1) Plug the mini-universal series bus (USB) connector into the E226. 2) Plug the connectors of the main USB data cable and the auxiliary USB data cable into the USB interfaces of the computer. PC 3) The OS automatically detects and recognizes the new hardware and displays on the status area of the desktop, indicating that the E226 is connected to the computer successfully. PC 2. Installing the E226 Manager 1) Connect the E226 to a computer. 2) The installation wizard automatically starts. If the installation wizard does not respond, double-click the AutoRun.exe file in the driver path to manually install the E226 Manager. 3) Follow the instructions to install the E226 Manager. Note: Do not disconnect the E226 during the installation process. 4) If the installation succeeds, the shortcut icon of the Manager appears on the desktop. 4 3. Removing the E226 To remove the E226, use the hardware deleting function of Windows. 1) Double-click on the status area of the desktop; the "Safely Remove Hardware" prompt is displayed. 2) Select "Huawei Mass Storage USB Device" to stop. 3) At the prompt, remove the E226.
Download:
Mirror Download [FCC.gov]
Document ID857425
Application IDS+DeVyKupuHbFFRI5z0STw==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize9.7kB (121211 bits)
Date Submitted2007-10-22 00:00:00
Date Available2007-10-22 00:00:00
Creation Date2007-10-19 17:03:05
Producing SoftwareAcrobat Distiller 6.0 (Windows)
Document Lastmod2007-10-19 17:03:05
Document Titleuntitled
FCC ID Filing: QISE226

Navigation menu