Huawei Technologies EG162 GSM/GPRS/EDGE USB Stick User Manual

Download:
Mirror Download [FCC.gov]
Document ID	864535
Application ID	35Ex8FotgG7QOumginq2cg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	10.07kB (125862 bits)
Date Submitted	2007-11-06 00:00:00
Date Available	2007-11-06 00:00:00
Creation Date	2007-10-08 11:54:07
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2007-10-09 16:55:51
Document Title	31018383-HUAWEI EG162 USB Modem Quick Start-(V100R001_01,English)
Document Creator	Acrobat PDFMaker 7.0 for Word
Document Author:	r48397

Copyright © 2007 Huawei Technologies Co., Ltd.
All Rights Reserved
No part of this manual may be reproduced or transmitted in any form or by any means
without prior written consent of Huawei Technologies Co., Ltd.
Trademarks
and HUAWEI are trademarks of Huawei Technologies Co., Ltd. All other
trademarks mentioned in this manual are the property of their respective holders.
Notice
The information in this manual is subject to change without notice. Every effort has been
made in the preparation of this manual to ensure accuracy of the contents, but all
statements, information, and recommendations in this manual do not constitute the
warranty of any kind, expressed or implied.
Table of Contents
Getting to Know the EG162 ....................................................................................1
Requirements for the PC..........................................................................................1
Preparing the EG162 ...............................................................................................2
Installation Guide.....................................................................................................2
Safety Information ...................................................................................................4
Thank you for purchasing Huawei EG162
USB Stick (hereinafter referred to as the
EG162).
1.
USB connector
Connects to the USB interface of the PC.
2.
SIM card slot
Fixes and bear the SIM card.
Note:
y This manual briefs the profiles of EG162,
3.
Indicator
It indicates the status of the EG162.
y Green, blinking twice every 3s: The EG162
is powered on.
y Green, blinking twice every 3s: The EG162
is registered to a GSM/GPRS/EDGE
network.
y Green, always on: The GSM/GPRS/EDGE
connection is set up.
y Blue, always on: SIM card is not installed.
SIM card is invalid. PIN code is required.
y Blue, blinking twice every 3s: The EG162
fails to search the network.
y Off: The EG162 is offline or removed from
a laptop.
including the preparation,
installation/uninstall process, and safety
precautions.
y You are highly recommended to read the
manual before using the EG162.
y The actual signal strength and the
transmission rate are affected by the
environment. If the singal stength is weak
when you use the USB Stick, you can move
the PC, or use the delivery-attached data
cable move the USB Stick.
Getting to Know the EG162
This is a sketch for EG162. The actual product
may differ.
Requirements for the PC
Before using the EG162, configure the
computer according to the following
requirements.
y USB interface: USB 2.0 full speed
y CPU: 866 MHz Pentium or above
y Memory: 128 MB or above
y Free space on the hard disk: 100 MB or
above
y Operating system: Windows XP, Windows
2.
Insert the SIM card into the card slot,
with the contact area on the card is facing
down and the beveled corner on the card
is facing inwards. Make sure that the
SIM card is fully in place.
3.
Insert the card slot with the SIM card
into the EG162.
2000 or Window Vista
y Screen resolution: 1024 × 768 is
recommended.
Note:
y Improper configurations may degrade the
wireless device performance. Make sure that
the computer configurations meet the
requirements.
y For Windows XP, it is recommended to
install patches such as Service Pack 2 or
above.
y For Windows 2000, it is recommended to
install patches such as Service Pack 4 or
above.
Preparing the EG162
1.
Press the right and left side of the cover,
and Remove it, take out the SIM card
slot.
Installation Guide
The procedure for installing the management
program is subject to the operating system
installed on your laptop. The following section
takes Windows XP as an example.
Installing the EG162
1.
Connect the EG162 to the USB interface
of the computer..
5.
6.
7.
2.
Launching the Mobile Partner
The driver runs automatically.
The Welcome interface is displayed.
After the EG162 is installed, Mobile Partner is
launched automatically. Then every time the
EG162 is connected to the PC, the Mobile
Partner is launched automatically.
Note:
3.
4.
Choose the install directory and click
Next.
The Choose Start Menu Folder
interface is displayed.
Choose or create the start menu folder
and click Install.
Mobile Partner is installed.
Click Finish to complete the installation.
If the driver does not run automatically,
double-click My Computer. Then
double-click Mobile Partner CD-ROM
to install the driver. Alternatively, open
My Computer > Mobile Partner. Then
double-click Autorun.exe to install it.
If there is more than one language, the
Installer Language interface is
displayed.
Select a language and click OK.
You can double-click the shortcut icon of
Mobile Partner to launch it.
Uninstalling the Mobile Partner
1.
2.
3.
Click Start Menu.
Click Control Panel.
Find the management program, and click
Add/Remove Program to uninstall it.
Note: It is recommended to restart the
computer after the uninstall to ensure
that Mobile Partner is completely
cleared.
Click Next.
The License Agreement interface is
displayed.
Read the license agreement carefully. If
you agree with the license agreement,
select I agree….
The Choose Install Location interface is
displayed.
Removing the EG162
1.
2.
Log out of Mobile Partner.
Remove the EG162.
To deactivate your wireless device, close all
applications using the wireless device first and
then remove the wireless device from your
PC.
Safety Information
Please read the safety information carefully to
ensure the correct and safe use of your
wireless device.
Obey all local laws, regulations, rules, orders,
signs and notices while using the wireless
device. Signs about the use of mobile phones
should also be obeyed as referring to other
wireless equipment including wireless
devices.
General Recommendations for Use
Always handle your wireless device with care
and keep it in a clean and dust-free place. Do
not expose your wireless device to open
flames or lit tobacco products.
Deactivate in Explosive Areas
y Always keep your wireless device dry.
Deactivate your wireless device where the air
is potentially explosive. It is rare, but your PC
could generate sparks.
y Do not drop, throw or try to bend your
wireless device.
Do not paint or scratch your wireless device.
Do not attempt to disassemble your wireless
device. Doing so will void warranty. Only
authorized personnel are allowed to do so.
This product requires a minimum distance
of 1.5 cm from the body when in operation.
Keep your wireless device in normal
temperature. Your wireless device can only
operate between -5ºC and +55 ºC.
Use approved accessories only. Do not
connect your wireless device to any
incompatible products.
Deactivate in Blasting Areas
Deactivate your wireless device where
blasting is in progress. Remote-controlled RF
devices are often used at construction sites to
set off blasting.
Deactivate in Aircrafts
Deactivate your wireless device before
boarding or in any aircraft. Wireless devices
can cause interference in aircrafts.
Obey Laws and Regulations
Deactivate at Hospitals
Do not operate your wireless device where it
may be unsafe to do so or where you are
required not to do so.
Obey regulations or rules at hospitals.
Deactivate your wireless device near medical
equipment. Wireless devices can cause
y If the wireless device or any of its
interference to cardiac pacemakers, implanted
defibrillators or other medical equipment.
accessories does not work, turn to an
authorized service center for help.
Deactivate near Hearing Devices
Environmental Protection
Deactivate your wireless device near hearing
devices. People with hearing aids may
experience interfering noises near wireless
devices.
Observe the local regulations regarding the
disposal of your packaging materials, old
wireless device and its accessories. Please
promote their recycling.
Recommendations for Children
SIM/USIM Cards
Do NOT allow children to play with your
wireless device. They could hurt themselves
or others, or could accidentally damage the
wireless device. Your wireless device contains
small parts with sharp edges that may cause an
injury or a choking hazard.
While inserting or removing the SIM card,
protect yourself against electrostatic discharge
(ESD). Do not touch the connector of the SIM
card. As a precaution, always make sure that
the wireless device is already in your hand
before you insert or remove the SIM card.
Deactivate While Driving
Restart on ESDs
Do not use the wireless device while driving.
Your wireless device is immune to
interferences caused by audible signals.
Software will attempt to re-initialize a
connection once a substantial electrostatic
discharge causes the device to reset. If the
software is not operational after an ESD,
restart the modem software application.
Cleaning and Maintenance
Agency/Regulatory Information
y Before you clean or maintain the wireless
The wireless device is approved for use in
many regions of the world. In these regions,
the device meets all radio frequency exposure
requirements. The following approvals and
notices apply in specific regions as noted.
Immunity to Interference
device, close all applications using wireless
device and remove your wireless device
from your PC.
y Clean your wireless device with a piece of
soft antistatic cloth.
CE Approval (European Union)
Certification Information (SAR)
The wireless device is approved to be used in
the member states of the EU. Huawei declares
that the wireless device is in compliance with
the essential requirements and other relevant
provisions of the Radio and
Telecommunications Terminal Equipment
Directive 1999/5/EC (R&TTE Directive).
THIS DEVICE MEETS THE
GOVERNMENT'S REQUIREMENTS FOR
EXPOSURE TO RADIO FREQUENCY
ELECTROMAGNETIC FIELD.
Your wireless device is a low-power radio
transmitter and receiver. When it is running, it
emits low levels of radio frequency energy
(also known as radio waves or radio frequency
fields).
Radio Frequency Exposure
To ensure compliance at all times with the
R&TTE Directive* 1999/5/EC, the wireless
device can be held in the hand but still
requires a minimum distance of 1.5 cm from
the body when in operation. For body-worn
use, it must be suitably mounted so that it is at
least 1.5 cm away from the body. Mounting
accessories (for example, belt clips) cannot be
made of metal. Do not put the wireless device
in your pocket.
Governments around the world have adopted
comprehensive international safety guidelines,
developed by scientific organizations, e.g.
ICNIRP (International Commission on
Non-Ionizing Radiation Protection) and IEEE
(Institute of Electrical and Electronics
Engineers Inc.), through periodic and
thorough evaluation of scientific studies.
These guidelines establish permitted levels of
radio wave exposure for the public. The levels
include a safety margin designed to assure the
safety of all persons, regardless of age and
health, and to account for any variations in
measurements.
* The general public RF exposure limits
referenced in the R&TTE Directive are
consistent with the published Guidelines of
the International Commission on
Non-Ionizing Radiation Protection (ICNIRP)
1998. ICNIRP is a formally recognized
non-governmental organization in
Non-Ionising Radiation Protection for the
World Health Organisation (WHO), the
International Labour Organisation (ILO) and
the European Union (EU). For more
information, visit the ICNIRP website at
www.icnirp.de.
Specific Absorption Rate (SAR) is the unit of
measurement for the amount of radio
frequency energy absorbed by the body when
using a wireless device. The SAR value is
determined at the highest certified power level
in laboratory conditions, but the actual SAR
level of the wireless device while operating
can be well below the value. This is because
the wireless device is designed to use the
it does not exceed the limit established by the
government-adopted requirement for safe
exposure.
minimum power required to reach the
network.
All models of Huawei’s wireless device are
designed to meet radio frequency exposure
guidelines such as European Council
Recommendation and Federal
Communications Commission Notice (United
States).
The SAR limit adopted by the USA and
Canada is 1.6 watts/kilogram (W/kg) averaged
over one gram of tissue. The highest SAR
value reported to the FCC and IC for this
device type when tested for use is 1.28 W/kg.
[There is no reference to the specific reference
standard or its applicability to the intended use
of the product]
European Council Recommendation:
Before a wireless device model is available
for sale to the public, it must be tested
according to the technical standard-EN 50361
and not exceed the limit established by the
European Council Recommendation:
1999/519/EC for safe exposure.
FCC Statement
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user
is encouraged to try to correct the interference
by one or more of the following measures:
The SAR limit adopted by the 1999/519/EC is
2.0 watts/kilogram (W/kg) averaged over ten
gram of tissue. The highest SAR value for this
device type when tested is 0.927 W/kg.
[EN 50361 scope states “This basic standard
applies to any electromagnetic field (EM)
transmitting devices intended to be used with
the radiating part of the equipment in close
proximity to the human ear including mobile
phones, cordless phones, etc. The frequency
range is 300 MHz to 3 GHz. Therefore, the
above text does not address primary use of the
wireless device product.]
Federal Communications Commission
Notice (United States): Before a wireless
device model is available for sale to the public,
it must be tested and certified to the FCC that
y Reorient or relocate the receiving antenna.
y Increase the separation between the
equipment and receiver.
y Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
y Consult the dealer or an experienced
radio/TV technician for help.
This device complies with Part 15 of the FCC
Rules and with RSS-210 of Industry Canada.
Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
Warning: Changes or modifications made to
this equipment not expressly approved by
HUAWEI may void the FCC authorization to
operate this equipment.
Version: V100R001_01
Part Number: 31018383

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
Page Count                      : 10
Page Layout                     : OneColumn
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:65949035-a054-422e-962d-f796fe3c2854
Producer                        : Acrobat Distiller 7.0 (Windows)
Company                         : Huawei Technologies Co., Ltd.
Source Modified                 : D:20071008035340
Headline                        : 
Creator Tool                    : Acrobat PDFMaker 7.0 for Word
Modify Date                     : 2007:10:09 16:55:51+08:00
Create Date                     : 2007:10:08 11:54:07+08:00
Metadata Date                   : 2007:10:09 16:55:51+08:00
Document ID                     : uuid:f82e35d9-5d1d-4642-b632-fe2a9815f9fd
Instance ID                     : uuid:1de81bcf-97d0-4efa-8923-5cf8a2221e75
Version ID                      : 672
Format                          : application/pdf
Title                           : 31018383-HUAWEI EG162 USB Modem Quick Start-(V100R001_01,English)
Creator                         : r48397
Subject                         : 
Description                     : 通用英文版本 Quick Start
Tagged PDF                      : Yes
Author                          : r48397

EXIF Metadata provided by EXIF.tools