Huawei Technologies EG8247H GPON Terminal User Manual
Huawei Technologies Co.,Ltd GPON Terminal
User manual
Quick Start
EchoLife HG8247H GPON Terminal
1
Safety Precautions
To use the device properly and safely, read the safety precautions carefully
before using the device and strictly observe these precautions when using
the device.
Do not look directly into the optical port without eye protection.
Keep the device out of the reach of children as the components or accessories may be
swallowed.
Install the device in strict compliance with the requirements of the supplier. Reserve a space of
at least 10 cm above and around the device for heat dissipation. During the installation, keep
the device away from electric appliances that generate strong magnetic or electric fields, such
as microwave ovens, refrigerators, and mobile phones.
The power supply voltage of the device must meet the requirements on the input voltage of the
device.
Do not use any power adapters that are not in the standard configuration. Otherwise, the
device may be abnormal or unsafe.
Dry your hands before connecting or disconnecting cables. Stop the device and switch off the
power before connecting or disconnecting cables.
Do not place any object on the device, so that the device will not be damaged due to
overheating or deformation.
Prevent objects, such as metal, from entering the device through the heat dissipation hole.
Switch off the power and disconnect all cables, including the power cable, optical fiber, and
network cable, during periods of lightning activities. The socket-outlet shall be installed near
the power adapter and shall be easily accessible. Before use the power adapter, please check
no damage on the adapter.
Do not lead the strength member of the optical fiber or other metal parts indoors. Do not install
telephone lines, network cables, power adapters or power adapter cables outdoors. Adopting
these measures will help prevent device damage and bodily injuries which are especially prone
during thunderstorms.
If an abnormality occurs, for example, liquid entering the device, smoke, unusual sound,
and smell, stop the device immediately, switch off the power, disconnect all cables (such as
the power cable, optical cable, and network cable) to the device, and contact the authorized
service center.
Do not disassemble the device without permission. In the case of a device fault, contact the
authorized service center.
Dispose of the packing materials, expired batteries, and old or abandoned devices in
accordance to local laws and regulations (recycling them is strongly recommended).
Do not change the structure, safety design, or performance design of the device without prior
authorization.
Fireproof precautions:
Keep the device away from large heat source equipment, bare ames, and high-power
devices, such as electric heaters, candles, and blow drier, to eliminate safety risks.
If there are aged cables or power socket facilities on the power supply line to or near the
device, replace them in time to eliminate safety risks. The power supply voltage of the device
must meet the input voltage requirement.
2
Product Overview
Product Function
HG8247H
4 Ethernet ports
2 POTS ports
1 USB port
1 CATV port
Wi-Fi access
Technical Specifications
NOTE
The appearance shown in this document may be different from the actual appearance
of the product. The actual product provided by the carrier prevails.
Installing the GPON Terminal
1. Do not install GPON terminals outdoors or on the outdoor cabinets.
2. GPON terminals can be mounted onto a wall or be placed on a
workbench. Do not install GPON terminals in other modes, such as the
ceiling.
3.The terminal cannot be connected to other devices such as GPON
terminals, switch and router.
Item Specifications
Dimensions (L x W x H) 220 mm x 160 mm x 32 mm (without
an external antenna)
Weight (including the power
adapter) About 800 g
System power supply See the nameplate on the device.
Power adapter input 100-240 V AC, 50-60 Hz
Maximum power consumption ≤18 W
Ambient temperature 0ºC- +40ºC
Ambient humidity 5% RH - 95% RH (non-condensing)
Mounting a GPON terminal on the desk
The figure below shows an HG8247H that is horizontally placed on a desk.
3
Mounting a GPON terminal onto the wall
Step 1 Mark the positions of two holes used for mounting a GPON terminal, ensure that
the two holes have the same spacing as the two mounting holes.
Step 2 Select a proper drill according to the outer diameter of the screws. Use a
hammer drill to drill the marked positions on the wall. Then clean the wall and
install two expansion bolts.
Step 3 Use a screwdriver to fasten the screws into the expansion bolts, leaving the heads
of the screws 3 mm over the wall. Then install the GPON terminal to the screws.
4
Connecting Cables
1Power switch
2Power port
3USB port
4POTS port
5Ethernet port
6Optical port
7CATV port
8Reset
9WLAN switch
WPS switch
10
5
NOTE
1.The optical connector connected to the OPTICAL port is an SC/APC connector, and the
type of the optical connector connected to the optical port in the wall is determined by practical
conditions.
2.To ensure normal use of fibers, make sure that the fiber bend radius is larger than 30 mm.
Step 2 Use a network cable to connect the LAN port to a PC or the Ethernet port on the
IP STB.
Step 3 Use a phone line to connect the TEL port to a phone or fax machine.
Step 4 Use a power adapter to connect the POWER port to the power socket.
The preceding figure connects the power adapter as an example. When connecting the
backup battery unit , please see the usage guide to the backup battery for details .
NOTE
Step 1 Use an optical fiber to connect the optical port on the ONT and the optical port on
the wall.The optical port of the HG8247H is at the back of the device.
Step 5 Use a USB data cable to connect the USB port to the USB storage device.
Step 6 Press the ON/OFF power switch.
Step 7 Press the WLAN switch to enable the Wi-Fi access function. By default, this
function is enabled.
Step 8 Press the WPS switch to enable the WPS encryption function.
Before enabling the WPS encryption function of a GPON terminal, ensure that the function is
set in the system software in advance. After successful setting, press the WPS switch for the
settings to take effect.
NOTE
11
11 Optical port
6
Logging in to the Web Configuration Window
NOTE
You can find the default management IP address on the nameplate of the
device.
NOTE
-If you do not perform any operations after logging in to the system for five minutes, you will
exit the system and the system automatically returns to the login interface.
-The system will be locked if you input incorrect user name and password three consecutive
times. One minute later, it will be unlocked.
-Change the initial password after logging in to the web page.
Step 1 Set the IP address of the PC in the same subnet as the management IP address
of the GPON terminal.
Step 2 Enter the management IP address of the GPON terminal in the address bar of
Internet Explorer and press Enter.
The login window is displayed.
Step 3 In the login window, select your preferred language, enter the user name and
password (see the device nameplate for the default user name and password),
and click Login. After the password is authenticated, the Web configuration
window is displayed.
7
Configuring Wi-Fi Parameters
Step 1 Choose the WLAN tab and choose WLAN Basic Configuration.
Step 2 In the pane, select the Enable WLAN option box. In the dialog box that is
displayed, set the basic Wi-Fi parameters, including the SSID, authentication
mode, and encryption mode.
Step 3 Click Apply.
-SSID: See the nameplate on the device
-WPA PreSharedKey: See the nameplate on the device
SSID indicates the name of a wireless network searched by the Wi-Fi terminal; WPA
PreSharedKey indicates the authentication password for the Wi-Fi terminal to access a
wireless network.
HG8247H supporting Wi-Fi , a wireless network coverage is subject to the number, thickness, and
positions of walls, materials, ceilings, or other objects that radio signals traverse. Besides, metarial
type and background radio frenquency (RF) noise also affect the coverage of a wireless network.
You can maximize the coverage of a wireless network using the following methods:
1. Decrease the number of walls and ceilings between HG8247H and other
network devices.
Each wall or ceiling reduces the coverage of a wireless network by one to 30
meters. Install HG8247H at a proper place to avoid walls or ceilings whenever
possible.
2. Observe the straight line rule when installing network devices.
The distance for which signals have to traverse at a 45° corner of two 0.5 meter-thick walls
reaches approximately one meter. To better receive signals, devices should be installed at
places where signals can directly traverse walls or ceilings.
3. Note the impact of building materials on the wireless network coverage.
A metal door or aluminum wall may limit the coverage of a wireless network. Install access
points, wireless routers, and computers, so signals can traverse walls or open passageways.
Materials and objects such as FRP products, metal products, insulative walls, filing cabinets,
bricks, and concrete weaken radio signals.
4. When connecting HG8247H to a wireless network, keep it far from the
following devices:
- Electronic devices or components that produce RF noises (keep a distance of more than 2
meters between such a device and HG8247H.)
- 2.4 GHz wireless mobile phones or X-10 devices (such as microwave ovens, home security
systems, blue-tooth devices, and refrigerators) that greatly weaken or even eliminate radio
signals. Even if a 2.4 GHz wireless mobile phone is not connected to a wireless network, the
phone base still sends signals that interfere the wireless network.
NOTE
Indicator Description
8
Table 1 Indicator status description 1
Indicator Status Description
CATV
Steady on The CATV function is enabled and CATV signals are received
Off The CATV function is disabled or CATV signals are not received.
WPS
Steady on The WPS function is enabled.
Blinking A Wi-Fi terminal is accessing the system.
Off The WPS function is disabled.
WLAN
Steady on The WLAN function is enabled.
Blinking Data is being transmitted on the WLAN port.
Off The WLAN function is disabled.
USB
Steady on The USB port is connected and is working in the host mode, but
no data is transmitted.
Blinks twice a
second Data is being transmitted on the USB port.
Off The system is not powered on or the USB port is not connected.
TEL1–
TEL2
Steady on The terminal is registered with the softswitch but no service ows
are transmitted.
Blinking Service ows are transmitted.
Off The terminal is not powered on or fails to be registered to the
softswitch.
LAN1–
LAN4
Steady on The Ethernet connection is in the normal state.
Blinking Data is being transmitted on the Ethernet port.
Off The Ethernet connection is not set up.
LOS/PON See Table 2.
POWER Steady green The terminal is powered on.
Off The power supply is cut off.
ErP Product Information
Hereby, Huawei Technologies Co.,Ltd. declares that the product meets
the directive 2009/125/EC and its implementation regulation (EC) NO
1275/2008 amended by (EC) 278/2009,(EC) 642/2009,(EU) 617/2013,(EU)
801/2013,and its implementation regulation (EC) NO 278/2009.
The power consumption of product in networked standby if all wired network
ports are connected and all wireless network ports are activated is 7.8 W.
For the product information displayed on the manufacturers’ freely
accessible websites required by (EU) No 801/2013 , please visit http://
support.huawei.com.
To turn on or off the wireless network function, press the WLAN button on
the side panel of the HG8247H.
Indicator Description
Table 2 Indicator status description 2
Status
No.
Status Description
PON LOS
1Off Off The GPON terminal is prohibited by the upper-layer
device, contact the service provider for help.
2Blinks twice a
second Off The GPON terminal attempts to set up a connection
with its upper-layer device.
3 Steady on Off A connection is set up between the GPON terminal
and its upper-layer device.
4Off Blinks once two
seconds
The GPON terminal is not connected to optical fibers
or does not receive optical signals.
5Blinks twice a
second
Blinks twice a
second
The GPON terminal is a rogue terminal, contact the
service provider for help.
6Blinks once
two seconds
Blinks once two
seconds The hardware is faulty.
9
FCC Statement
FCC Radiation Exposure Statement
RF Exposure
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC
RF Rules. This equipment must be installed and operated in accordance
with provided instructions and the antenna(s) used for this transmitter
must be installed to provide a separation distance of at least 20cm from all
persons and must not be co-located or operating in conjunction with any
other antenna or transmitter. End-users and installers must be provide with
antenna installation instructions and consider removing the no-collocation
statement. This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
withminimum distance 20cm between the radiator & your body.
NOTE
Contents marked with * are applicable to America.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Caution
10
11
The LOS indicator blinks.
If the LOS indicator blinks once two seconds, check whether the pigtail fiber
is properly connected and the connector is clean.
If the GPON terminal blinks twice a second, contact the service provider for
help.
The PON indicator is off.
Check whether the OPTICAL port and optical fiber is properly connected.
The GPON terminal fails to register with the upper-layer device. Contact the
service provider for help.
The phone does not ring upon an incoming call but communication is in
normal state when the phone is in off-hook state.
The GPON terminal provides a maximum of 60 V AC ringing current
voltage. Check whether the ringing current voltage of the phone is higher
than 60 V AC. If it is higher than 60 V AC, replace it with another phone.
How to reset the GPON terminal?
Press Reset by using a needle-type object.
How can I restore factory defaults?
Press Reset by using a needle-type object for longer than 10s to restore
factory defaults and reset the GPON terminal. If the indicator is off and then
is lit, the system restarts successfully.
FAQs
User Information
Personal or
company's full name:__________________________________________________
Address/Postal Code:_________________________________________________
Telephone:__________________________________________________________
Email:______________________________________________________________
Product Type:________________________________________________________
Product Serial Number:________________________________________________
Purchase Date:______________________________________________________
Invoice Number:______________________________________________________
Dealer's Name:______________________________________________________
Dealer's Address:_____________________________________________________
Dealer's Telephone:___________________________________________________
Warranty Card
Thank you for choosing Huawei Technologies Co., Ltd. To get better services,
please read this warranty card carefully, fill in the required information, and
preserve this card in good condition.
Preserve well. No reissue.
Dealer's Seal
Limited Warranty
Subject to the exclusions contained below, Huawei Technologies Co., Ltd. (Huawei
for short) warrants its access terminals ("Products") to be free from defects in
materials and workmanship under normal consumer usage for one year from
the date of purchase of the product ("Warranty period"). During the warranty
period, a Huawei authorized service partner shall remedy defects in materials and
workmanship free of charge.
Special Notice:
1. The warranty card shall be applicable only after being stamped by the dealer.
2. The warranty card must be preserved in good condition and free of any scratch or
alteration.
3. To claim such service for defects that are not included in the following exclusion
terms, the warranty card and the invoice that records that product serial number
shall be presented to a Huawei authorized service partner.
Exclusions:
In any of the following cases, the warranty card becomes unenforceable or
inapplicable without prior notice:
1. The defects are caused by improper handling in transportation and assembly.
2. The defects are caused by the fact that the product is dismantled or altered by
anyone that is not from a Huawei authorized service partner.
3. The defects are caused by the fact that the product is used in a harsh environment
that is not suitable for the operation of the product.
4. The defects are caused by any force majeure including but not limited to fire,
earthquake, lightning, and tsunami.
5. The defects are caused by the fact that the product is used or handled incorrectly,
roughly or not as instructed in the applicable User Guide.
6. The normal wear and tear, including but not limited to the normal wear and tear of
the shell and the power module, shall not be covered by the limited warranty.
7. The warranty card is altered or illegible, or the product serial number recorded on
the warranty card is inconsistent with the actual one imprinted or labeled on the
product.
In any case that is not covered by this limited warranty or should the warranty expire,
Huawei shall charge for the service(s) claimed for the products if the product is still
remediable. Huawei reserves all rights to interpret this limited warranty.
Huawei Technologies Co., Ltd.
Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website: http://www.huawei.com
Issue: 02 (2015-05-30)
BOM number: 31507029
Qualification Card
PASS
Copyright © Huawei Technologies Co., Ltd. 2015 All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any
means without prior written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of
their respective holders.
Notice
The information in this document is subject to change without notice. Unless
otherwise stated, this guide serves only as a guide. All statements, information, and
recommendations in this document do not constitute a warranty of any kind, expressed
or implied.