Huawei Technologies EM820W HSPA+ Module User Manual Hardware Description

Huawei Technologies Co.,Ltd HSPA+ Module Hardware Description

UserManual.wiki >

Huawei Technologies >

EM820W User Manual >

User manual II

Huawei AR1200-S&2200-S Series EnterpriseRoutersV200R001C01Hardware DescriptionIssue 03Date 2012-04-20HUAWEI TECHNOLOGIES CO., LTD.

Copyright © Huawei Technologies Co., Ltd. 2012. All rights reserved.No part of this document may be reproduced or transmitted in any form or by any means without prior writtenconsent of Huawei Technologies Co., Ltd. Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.All other trademarks and trade names mentioned in this document are the property of their respective holders. NoticeThe purchased products, services and features are stipulated by the contract made between Huawei and thecustomer. All or part of the products, services and features described in this document may not be within thepurchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,and recommendations in this document are provided "AS IS" without warranties, guarantees or representationsof any kind, either express or implied.The information in this document is subject to change without notice. Every effort has been made in thepreparation of this document to ensure accuracy of the contents, but all statements, information, andrecommendations in this document do not constitute the warranty of any kind, express or implied. Huawei Technologies Co., Ltd.Address: Huawei Industrial BaseBantian, LonggangShenzhen 518129People's Republic of ChinaWebsite: http://www.huawei.comEmail: support@huawei.comIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.i

About This DocumentIntended AudienceThis document provides an overall description of the AR routers, details about each chassis andboard, cables available to the device, and lists of components.This document is intended for:lNetwork planning engineerslHardware installation engineerslCommissioning engineerslOn-site maintenance engineerslSystem maintenance engineersSymbol ConventionsThe symbols that may be found in this document are defined as follows.Symbol DescriptionDANGERIndicates a hazard with a high level of risk, which if notavoided, will result in death or serious injury.WARNINGIndicates a hazard with a medium or low level of risk, whichif not avoided, could result in minor or moderate injury.CAUTIONIndicates a potentially hazardous situation, which if notavoided, could result in equipment damage, data loss,performance degradation, or unexpected results.TIPIndicates a tip that may help you solve a problem or savetime.NOTEProvides additional information to emphasize or supplementimportant points of the main text. Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description About This DocumentIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.ii

Change HistoryChanges between document issues are cumulative. Therefore, the latest document issue containsall the changes in previous issues.Changes in Issue 02 (2012-03-30)Based on issue 01 (2011-12-30), this issue has the following updates:lThe AR2220-S model is added.Changes in Issue 01 (2011-12-30)Initial commercial release.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description About This DocumentIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.iii

ContentsAbout This Document.....................................................................................................................ii1 Version Matching..........................................................................................................................11.1 Matching Between Product Models and Software Versions..............................................................................21.2 Matching Between Power Supplies and Software Versions..............................................................................21.3 Matching Between Cards and Software Versions..............................................................................................32 Chassis.............................................................................................................................................72.1 Introduction........................................................................................................................................................82.2 Naming Convention............................................................................................................................................82.3 Device Structure.................................................................................................................................................92.3.1 AR1200-S Series.......................................................................................................................................92.3.2 AR2200-S Series.....................................................................................................................................122.4 System Configuration.......................................................................................................................................142.5 Physical Specifications.....................................................................................................................................143 Power Supply Units....................................................................................................................163.1 Power Supply Configuration............................................................................................................................173.2 Power Supply Unit Connection Layouts..........................................................................................................173.2.1 Single Non-PoE AC Power Supply Unit.................................................................................................173.2.2 Single Non-PoE + PoE AC Power Supply Unit......................................................................................183.3 HW-100-48AC14D..........................................................................................................................................194 Heat Dissipation System............................................................................................................234.1 Heat Dissipation Process..................................................................................................................................245 Cards..............................................................................................................................................255.1 Introduction......................................................................................................................................................265.1.1 Relationships Between Cards..................................................................................................................265.1.2 Interface Numbering................................................................................................................................275.1.3 Card Dimensions.....................................................................................................................................285.2 WLAN Subcard................................................................................................................................................295.2.1 Functions and Applications.....................................................................................................................295.2.2 Technical Specifications..........................................................................................................................295.3 Ethernet LAN Interface Card............................................................................................................................295.3.1 8FE1GE-8-Port 100BASE-RJ45 and 1-Port 1000BASE-RJ45 L2/L3 Ethernet Interface Card.............30Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description ContentsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.iv

5.3.2 24GE-24-Port 1000BASE-RJ45 L2/L3 Ethernet Interface Card............................................................335.4 WAN Interface Card.........................................................................................................................................365.4.1 1GEC (1-Port-GE Combo WAN Interface Card)....................................................................................365.4.2 2FE-2-Port-FE WAN Interface Card.......................................................................................................405.4.3 1E1T1-M/2E1T1-M-1/2 Port-Channelized E1/T1/PRI/VE1 Multifunctional Interface Card................425.4.4 1E1T1-F/2E1T1-F (1/2-Port-Fractional Channelized E1/T1 WAN Interface Card)..............................475.4.5 1SA/2SA-1/2-Port-Synchronous/Asynchronous WAN Interface Card..................................................505.4.6 8AS (8-Port-Asynchronous WAN Interface Card)..................................................................................545.4.7 1BST (1-Port-ISDN S/T WAN Interface Card)......................................................................................565.4.8 1CPOS-155M (1-Port Channelized POS Interface Card).......................................................................595.4.9 3G-HSPA+7 (3G WAN Interface Card).................................................................................................625.4.10 4GEW-T (4-Port-GE Electrical WAN Interface Card).........................................................................675.4.11 4GEW-S (4-Port-GE Optical WAN Interface Card..............................................................................695.5 Voice Interface Card.........................................................................................................................................735.5.1 2BST (2-Port-ISDN S/T Voice Interface Card)......................................................................................735.5.2 4FXS1FXO-4-Port FXS and 1-Port FXO Voice Interface Card.............................................................775.5.3 16/32/64/128-Channel DSP Module.......................................................................................................805.6 xDSL Interface Card.........................................................................................................................................815.6.1 ADSL-A/M and ADSL-B-1-Port-ADSL2+ ANNEX A/M and B WAN Interface Card........................815.6.2 4G.SHDSL-1-Port-4-Channel G.SHDSL WAN Interface Card.............................................................855.6.3 1PON (1-Port GPON/EPON Dual-Mode Interface Card).......................................................................875.6.4 VDSL (1-Port VDSL2 over POTS WAN Interface Card)......................................................................916 Cables.............................................................................................................................................956.1 AC Power Cable...............................................................................................................................................976.2 DC Power Cables..............................................................................................................................................986.3 Ground Cable..................................................................................................................................................1006.4 Console Cable.................................................................................................................................................1016.5 Network Cable................................................................................................................................................1026.6 Optical Fiber...................................................................................................................................................1056.7 E1/T1 Trunk Cables........................................................................................................................................1096.8 Synchronous/Asynchronous Serial Interface Cables......................................................................................1146.9 4G.SHDSL Cables..........................................................................................................................................1206.10 ISDN-ST Cables...........................................................................................................................................1226.11 Regular Telephone Lines..............................................................................................................................1266.12 8AS Cable.....................................................................................................................................................1276.13 3G Antenna...................................................................................................................................................1327 List of Indicators........................................................................................................................1367.1 Indicators on the AR1200-S Panel.................................................................................................................1377.2 Indicators on the AR2220-S Panel.................................................................................................................1407.3 Power Indicators.............................................................................................................................................1428 List of Cards................................................................................................................................145Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description ContentsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.v

8.1 Cards Supported by the AR............................................................................................................................1468.2 Power Consumption and Weight....................................................................................................................1499 List of Interface Attributes.......................................................................................................1509.1 Electrical Interfaces........................................................................................................................................1529.2 GE/PON Optical Interface Attributes.............................................................................................................1539.3 CPOS Interface Attributes..............................................................................................................................1559.4 E1 Interface Attributes....................................................................................................................................1569.5 T1 Interface Attributes....................................................................................................................................1579.6 Synchronous/Asynchronous Serial Interface Attributes.................................................................................1589.7 ISDN S/T Interface Attributes........................................................................................................................1599.8 FXS/FXO Interface Attributes........................................................................................................................1599.9 ADSL2/ADSL2+/G.SHDSL Interface Attributes..........................................................................................1619.10 Attributes of the Console Interface...............................................................................................................1629.11 Attributes of the USB Interface....................................................................................................................1629.12 3G Interface Attributes.................................................................................................................................1639.13 VDSL Interface Attributes............................................................................................................................164Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description ContentsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.vi

1 Version MatchingAbout This ChapterThis section describes the matching relationships between the chassis, power supplies, cards,and system software versions of AR routers.NOTElAR version roadmap: ARV200R001C01, ARV200R002C00, ARV200R002C01.lUnless otherwise specified, if a power supply or card is supported by version A, it is also supported byall versions later than version A.1.1 Matching Between Product Models and Software VersionsThis section describes the matching relationship between AR models and software versions.1.2 Matching Between Power Supplies and Software VersionsThis section describes the matching relationships between power supplies, power modes, andsoftware versions.1.3 Matching Between Cards and Software VersionsThis section describes the cards supported by AR routers, including SRUs, Ethernet LANinterface cards, WAN interface cards, voice interface cards, and xDSL/xPON interface cards.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 1 Version MatchingIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.1

1.1 Matching Between Product Models and SoftwareVersionsThis section describes the matching relationship between AR models and software versions.Table 1-1 Matching between product models and software versionsModel Software VersionARV200R001C01 ARV200R002C00 ARV200R002C01AR1200-SseriesAR1220-S√ √ √AR1220W-S√ √ √AR2200-SseriesAR2220-S√ × √ 1.2 Matching Between Power Supplies and SoftwareVersionsThis section describes the matching relationships between power supplies, power modes, andsoftware versions.Table 1-2 Matching between power supplies and software versionsModel&Version 60 W ACPowerSupply Unitin an OpenRack3.3HW-100-48AC14DPWR150AARV200R001C01&ARV200R002C00&ARV200R002C01AR1220-S √ × ×AR1220W-S√ √ ×AR2220-S × × √ Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 1 Version MatchingIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.2

Table 1-3 Matching between power modes and software versionsModel&VersionSingleDCPowerSupplyUnitDual DCPowerSupplyUnitsSingleNon-PoEAC PowerSupplyUnitDual Non-PoE ACPowerSupplyUnitsSingleNon-PoE+ PoE ACPowerSupplyUnitARV200R001C01&ARV200R002C00&ARV200R002C01AR1220-S× × √ × ×AR1220W-S× × √ × √AR2220-S× × √ × × 1.3 Matching Between Cards and Software VersionsThis section describes the cards supported by AR routers, including SRUs, Ethernet LANinterface cards, WAN interface cards, voice interface cards, and xDSL/xPON interface cards.Matching between physical cards and software versionsTable 1-4 Matching between physical cards and software versionsModel&Version SIC WSIC XSIC voice cardARV200R001C01&ARV200R002C00&ARV200R002C01AR1220-S√ √ × ×AR1220W-S√ √ × ×AR2220-S√ √ √ √ Matching between SRUs and software versionsTable 1-5 Matching between SRUs and software versionsModel&Version SRU WLAN SubcardARV200R001C01&ARV200R002AR1220-S × ×Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 1 Version MatchingIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.3

Model&Version SRU WLAN SubcardC00&ARV200R002C01AR1220W-S × √AR2220-S × × Matching between Ethernet LAN interface cards and software versionsTable 1-6 Matching between Ethernet LAN interface cards and software versionsModel&Version 8FE1GE 24GEARV200R001C01&ARV200R002C00&ARV200R002C01AR1220-S √ ×AR1220W-S √ ×AR2220-S √ √ Matching between WAN cards and software versionsTable 1-7 Matching between WAN cards and software versionsModel&Version2FE1E1T1-M/2E1T1-M(SIC)2E1T1-M(WSIC)1E1T1-F/2E1T1-F1SA2SA1GEC8AS1BST1CPOS-155M3G-HSPA+74GEW-T4GEW-SARV200R001C01AR1220-S√ √ × √ √ √ √ √ √ × × × ×AR1220W-S√ √ × √ √ √ √ √ √ × × × ×AR2220-S√ √ × √ √ √ √ √ √ √ × × ×ARV200R002C00AR1220-S√ √ √ √ √ √ √ √ √ × × × ×Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 1 Version MatchingIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.4

Model&Version2FE1E1T1-M/2E1T1-M(SIC)2E1T1-M(WSIC)1E1T1-F/2E1T1-F1SA2SA1GEC8AS1BST1CPOS-155M3G-HSPA+74GEW-T4GEW-SAR1220W-S√ √ √ √ √ √ √ √ √ × × × ×AR2220-S√ √ √ √ √ √ √ √ √ √ × × ×ARV200R002C01AR1220-S√ √ √ √ √ √ √ √ √ × √ √ √AR1220W-S√ √ √ √ √ √ √ √ √ × √ √ √AR2220-S√ √ √ √ √ √ √ √ √ √ √ √ √ Matching between voice cards and software versionsTable 1-8 Matching between voice cards and software versionsModel&Version 4FXS1FXO 2BST(SIC) 2BST(WSIC) 16/32/64/128-ChannelDSPModuleARV200R001C01AR1220-S× × × ×AR1220W-S× × × ×AR2220-S√ √ × √ARV200R002C00&ARV200R002C01AR1220-S× × × ×AR1220W-S× × × ×Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 1 Version MatchingIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.5

Model&Version 4FXS1FXO 2BST(SIC) 2BST(WSIC) 16/32/64/128-ChannelDSPModuleAR2220-S√ √ √ √ Matching between xDSL/xPON cards and software versionsTable 1-9 Matching between xDSL/xPON cards and software versionsModel&VersionADSL-A/MADSL-B4G.SHDSL1PON VDSLARV200R001C01AR1220-S√ √ √ × ×AR1220W-S√ √ √ × ×AR2220-S√ √ √ × ×ARV200R002C00AR1220-S√ √ √ √ ×AR1220W-S√ √ √ √ ×AR2220-S√ √ √ √ ×ARV200R002C01AR1220-S√ √ √ √ √AR1220W-S√ √ √ √ √AR2220-S√ √ √ √ √ Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 1 Version MatchingIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.6

2 ChassisAbout This ChapterThis section describes the characteristics, naming rules, appearance, structure, systemperformance, and technical specifications of the AR routers.2.1 IntroductionThis section briefly describes the AR routers and the models available.2.2 Naming ConventionThis section describes the naming conventions used when naming AR routers.2.3 Device StructureThis section describes the structure of the AR routers.2.4 System Configuration2.5 Physical SpecificationsHuawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 2 ChassisIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.7

2.1 IntroductionThis section briefly describes the AR routers and the models available.DescriptionHuawei AR Enterprise Router (AR router for short) are the next-generation routers integratingdata,voice, security, routing, switching, and virtual private network (VPN) functions. As anegress gateway for enterprises, the AR routers use the multi-core CPU processing capabilitiesand rapid expansibility.ModelsThe AR routers offer the following models.Model CharacteristicsAR1200-SAR1220-SThe AR1220-S is 1 U high (1 U = 44.45 mm [1.75 in.]), uses a 60 Wopen frame AC power supply, and supports two SIC slots. Theintegrated SRU provides eight fixed FE interfaces and two fixed GEelectrical interfaces.AR1220W-SlCompared with the AR1220-S, the AR1220W-S supports the Wi-Fi function and external PoE power supply unit. The last four FEinterfaces (FE4-FE7) on the main control unit support the PoEfunction.lThe silkscreen on the rear side of AR1220W-S chassis isAR1220W-S and two antennas and a PoE power supply port areprovided.AR2200 AR2220-SThe AR2220-S is 1 U high (1 U = 44.45 mm), uses a 150 W AC powersupply unit, and supports four SIC cards and two WSIC cards. Theintegrated SRU supports fixed 3GE interfaces (including one combointerface). The backplane is in the middle of the chassis, and cardsare installed on the front and rear sides of the backplane. NOTElSIC: Service Interface Card. This is the smallest card supported by ARs.lWSIC: Wide SIC. The same height as a SIC, but twice the width.lXSIC: Extended SIC. Double the height and width of an XSIC and twice those of a SIC.NOTEIn this document, AR1200–S indicates AR1220–S and AR1220W–S.2.2 Naming ConventionThis section describes the naming conventions used when naming AR routers.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 2 ChassisIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.8

Figure 2-1 Naming convention【AR】【B1 B2 B3 B4】【C1】【-D1】Example:AR1220 -S Table 2-1 Naming convention of AR routersField DescriptionB1 Product series code. AR routers includes series 1 and 2.B2 Fixed as 2, indicating enterprise router.B3 Number of service card slots (dependent on B1):lWhen B1 is 1, B3 indicates the number of SIC cards.lWhen B1 is 2, B3 indicates the number of WSIC and XSIC cards.B4 The value is fixed as 0.C1 C1 contains one or two upper-case letters.lW: WLANlV: voiceD1 lA: AC (This is the default configuration, so A is not contained inthe product name)lD: DClS: Soho 2.3 Device StructureThis section describes the structure of the AR routers.2.3.1 AR1200-S SeriesThis section describes the structure of the AR1200-S.AppearanceFigure 2-2 and Figure 2-3 show front views of AR1200-S.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 2 ChassisIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.9

Figure 2-2 AR1220-S front view18 Figure 2-3 AR1220W-S front view201819 Figure 2-4 and Figure 2-5 show rear views of AR1200-S.Figure 2-4 AR1220-S rear view2 4 3171012131415 Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 2 ChassisIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.10

Figure 2-5 AR1220W-S rear view2 4 317101213 111415 1: Pluggable card 2: ESD jack 3: Ground screw 4: AC jack7: Security lock 10: AC power switch 11: PoE port 12: Fixed 8FE interfaceon the panel13: Two Fixed GEinterfaces on the panel14: Mini USBinterface15: CON/AUXinterface18: USB interfacesNOTEAfter a 3G USB modemis inserted, install aprotection cap on it, asshown in the followingfigure.19: Antenna 20: WLAN switchSlot DistributionFigure 2-6 shows slot distribution on AR1200-S.NOTElTwo SIC slots can be combined into one WSIC slot by removing the guide rail.lSlots can be combined into one, but one slot cannot be divided into multiple slots.lAfter two slots are combined into one, the slot ID is the larger number of the two original slots.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 2 ChassisIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.11

Figure 2-6 AR1200-S slot distribution onFront viewRear viewDevice Model Slot DistributionAR1200-SNATwo SIC slots are combined into one WSIC slotNA1(SIC)2(SIC)0(SRU)Slot Combination2(WSIC)0(SRU) As shown in Figure 2-6, the slots of AR1200-S can be combined :Slot 1 and slot 2 are combined into new slot 2.2.3.2 AR2200-S SeriesThis section describes the structure of the AR2200-S.AppearanceFigure 2-7 show front views of AR2200-S.Figure 2-7 AR2220-S front view41014 151317 1816 Figure 2-8 show rear views of AR2200-S.Figure 2-8 AR2220-S rear view123 1: Pluggable card 2: ESD jack 3: Ground screw 4: AC jackHuawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 2 ChassisIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.12

10: AC power switch 13: Two Fixed GEinterfaces on the panel14: Mini USB interface 15: CON/AUXinterface16: Micro SD cardinterface17: GE optical/electrical Combointerface18: USB interfacesNOTEAfter a 3G USB modemis inserted, install aprotection cap on it, asshown in the followingfigure.Slot DistributionFigure 2-9 shows slot distribution on AR2200-S.NOTElTwo SIC slots can be combined into one WSIC slot by removing the guide rail.lTwo SIC slots and one WSIC slot can be combined into one XSIC slot by removing the guide rail.lTwo XSIC slots can be combined into one EXSIC slot by removing the guide rail.lSlots can be combined into one, but one slot cannot be divided into multiple slots.lAfter two slots are combined into one, the slot ID is the larger number of the two original slots.Figure 2-9 AR2200-S slot distributionAR2220-SNA0(SRU)7(Power)Front viewRear viewDevice Model Slot DistributionTwo SIC slots are combined into one WSIC slotSlot CombinationTwo WSIC slots are combined into one XSIC slot5(XSIC)6(XSIC)2(WSIC)4(WSIC)5(WSIC)6(WSIC)2(SIC)3(SIC)4(SIC)5(WSIC)6(WSIC)1(SIC) As shown in Figure 2-9, the slots of AR2200-S can be combined :lAR2220-S–Slot 1 and slot 2 are combined into new slot 2.–Slot 3 and slot 4 are combined into new slot 4.–New slot 2 and slot 5 are combined into new slot 5.–New slot 4 and slot 6 are combined into new slot 6.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 2 ChassisIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.13

2.4 System ConfigurationTable 2-2 System configurationModel Processor Memory FlashMemoryMicro SD CardAR1200-SSeries2-core: 500MHz512 MB 256 MB 0AR2220-S 4-core: 600MHz2 GB 16 MB 2 GB 2.5 Physical SpecificationsTable 2-3 Physical specificationsItem DescriptionDimensions (width x depth x height) lWithout rack-mounting ear:–AR1200-S: 390.0 mm x 220.0 mm x 44.5mm (15.35 in. x 8.66 in. x 1.75 in.)–AR2220-S: 442.0 mm x 420.0 mm x 44.5mm (17.4 in. x 16.54 in. x 1.75 in.)lWith rack-mounting ear:–AR1200-S: 482.6 mm x 220.0 mm x 44.5mm (19 in. x 8.66 in. x 1.75 in.)–AR2220-S: 482.6 mm x 420.0 mm x 44.5mm (19 in. x 16.54 in. x 1.75 in.)MaximumpowerconsumptionFull configuration lAR1200-S: 52 WlAR2220-S: 95 WEmpty chassis lAR1200-S: 33.3 WlAR2220-S: 65.1 WWeight Full configuration lAR1200-S: 3.60 kg (7.94 lb)lAR2220-S: 8.45 kg (18.63 lb)Empty chassis lAR1200-S: 2.90 kg (6.39 lb)lAR2220-S: 4.95 kg (10.91 lb)Operating temperature 0°C to 40°C (0°F to 104°F)Relative humidity 5% RH to 90% RH, non-condensingHuawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 2 ChassisIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.14

Item DescriptionAltitude Long-term operatingaltitudeBelow 4000 m (13123.2 ft.)Storage altitude Below 4000 m (13123.2 ft.)AC inputvoltageRated voltage 100 V AC to 240 V AC, 50/60HzMaximum voltage 85 V AC to 264 V AC, 47/63Hz Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 2 ChassisIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.15

3 Power Supply UnitsAbout This ChapterThis section describes the power supply units supported by the AR routers.CAUTIONlPower off the AR routers before removing or performing maintenance on the power supplyunits.lTo power off the AR routers , power off all its power supply units.3.1 Power Supply ConfigurationThis section describes the configurations of power supply units on the AR routers.3.2 Power Supply Unit Connection LayoutsThis section illustrates the connection between each power supply unit and the motherboard.3.3 HW-100-48AC14DThis section describes the HW-100-48AC14D power supply unit, including the namingconvention, functions, appearance, and technical specifications.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 3 Power Supply UnitsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.16

3.1 Power Supply ConfigurationThis section describes the configurations of power supply units on the AR routers.Table 3-1 describes the power supply units supported by each model.Table 3-1 Power supply units supported by each modelPower Supply Unit Description Installation Maintenance60 W AC powersupply unit in an openrackAC power supplyunit fixed in thechassisFixed in the chassis,does not need to beconnected to thechassis usingcables.Maintain together withthe chassis.3.3HW-100-48AC14DExternal PoE ACpower supply unitConnected to thePoE port at the backof the chassis usingits own powercable.Maintainindependently from thechassis.PWR150A AC power supplyunitInserted into apower supply slot.The device supportsonly one powersupply unit.Maintain together withthe chassis. 3.2 Power Supply Unit Connection LayoutsThis section illustrates the connection between each power supply unit and the motherboard.3.2.1 Single Non-PoE AC Power Supply UnitFigure 3-1 shows the layout of single non-PoE AC power supply unit connection tomotherboard.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 3 Power Supply UnitsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.17

Figure 3-1 Layout of single non-PoE AC power supply unit connection to motherboardMotherboardGND12VPWRL N PGND1. L: Live wire 2. N: Neutral wire 3. PGND: PGND wire 4. GND: GroundingAfter the AC power is transmitted to the PWR module, the PWR module outputs 12 V voltage,and then the motherboard provides power for the entire device.3.2.2 Single Non-PoE + PoE AC Power Supply UnitFigure 3-2 shows the layout of single non-PoE + PoE AC power supply unit connection tomotherboard.Figure 3-2 Layout of single non-PoE + PoE AC power supply unit connection to motherboardMotherboardGND12VPWRL N PGNDPWRL N PGNDRTN-53VRTN-53VPSE on the SRUPoE Port (FE4~FE7)1. L: Live wire 2. N: Neutral wire 3. PGND: PGND wire 4. GND: Grounding 5. RTN: Power ground cableThe non-PoE AC power supply unit and PoE AC power supply unit are independent of eachother:lNon-PoE AC power supply unit: After the AC power is transmitted to the PWR module,the PWR module outputs 12 V voltage, and then the motherboard provides power for theentire device.lPoE AC power supply unit: After the AC power is transmitted to the PoE module, the PoEmodule outputs -53 V voltage, and then the PSE on the SRU provides power for the powereddevices (PDs) connected to the PoE interface.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 3 Power Supply UnitsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.18

Table 3-2 Protection functions of the HW-100-48AC14DItem Minimum ValueTypicalValueMaximum ValueRemarksInputprotectionInputundervoltageprotection- - 62 V Input voltage can berestored to the normalrange automatically.Inputundervoltage recovery- - 80 V Hysteresis is not smallerthan 5 V.OutputprotectionOutputovervoltage protection51 V - 58 V Output voltage can berestored to the normalrange automatically.Outputovercurrentprotection2.5 A 3 A 3.5 A Output current can berestored to the normalrange automatically.Outputshort-circuitprotection- - - Output short-circuit can berecovered automatically.Overheating protection - - - When temperature exceedsthe upper limit, the powersupply unit automaticallyshuts down to avoidpermanent damage. Nosmoke will be generated.Temperature is reducedbelow 55°C (131°F). AppearanceFigure 3-4 shows the appearance of the HW-100-48AC14D.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 3 Power Supply UnitsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.20

Figure 3-4 Appearance of the HW-100-48AC14D Table 3-3 describes meanings of the indicators.Table 3-3 Description of the HW-100-48AC14D indicatorsIndicator Color DescriptionPower indicator Blue If the indicator is steady on, the output power isin the normal range.If the indicator is off, the power supply unit doesnot have output power. Technical SpecificationsTable 3-4 describes the technical specifications of the HW-100-48AC14D.Table 3-4 Technical specifications of the HW-100-48AC14DItem SpecificationDimensions (widthx depth x height)72 mm x 171 mm x 40 mm (2.83 in. x 6.73 in. x 1.57 in.)Weight 0.65 kg (1.5 lb)AC input voltage 90 V AC to 264 V AC; typical: 110 V AC/220 V ACAC inputfrequency47 Hz to 63 Hz; typical: 50 Hz/60 HzHuawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 3 Power Supply UnitsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.21

Item SpecificationRated operatingvoltage100 V AC to 240 V AC; typical: 110 V AC/220 V ACRated outputcurrent2.08 ARated outputvoltage48 VOutput power 100 WOperatingtemperature0°C to 40°C (0°F to 104°F)Humidity 20% RH to 80% RHAltitude 4000 m (13123.2 ft.) Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 3 Power Supply UnitsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.22

4 Heat Dissipation SystemAbout This ChapterThis section describes the heat dissipation system of the AR router.The fan module of the AR router is described as follows:lThe fan module of the AR1200-S and AR2220-S is located on the right side in the chassis.–The fan module dimensions of the AR1200-S are 40 mm [1.58 in.] (width) x 20 mm[0.79 in.] (depth).–The fan module dimensions of the AR2220-S are 40 mm [1.58 in.] (width) x 20 mm[0.79 in.] (depth).4.1 Heat Dissipation ProcessThe AR routers heat dissipation system uses fans to create a left-to-right air channel.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 4 Heat Dissipation SystemIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.23

4.1 Heat Dissipation ProcessThe AR routers heat dissipation system uses fans to create a left-to-right air channel.NOTEThe heat dissipation system ensures that the AR routers operates at a normal temperature. For temperaturerequirements, see 2.5 Physical Specifications.Figure 4-1 shows air circulation through the AR1200-S chassis.Figure 4-1 Air circulation through the AR1200-S chassis Figure 4-2 shows air circulation through the AR2220-S chassis.Figure 4-2 Air circulation through the AR2220-S chassis Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 4 Heat Dissipation SystemIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.24

5 CardsAbout This ChapterThis chapter describes the cards supported by the AR routers.5.1 IntroductionThis section describes the cards supported by the AR routers, including card types, relationshipsbetween cards, the interface numbering scheme, and card dimensions.5.2 WLAN SubcardWLAN subcards are Wi-Fi modules.5.3 Ethernet LAN Interface CardThis section describes the types, functions, applications, appearance, interfaces, and technicalspecifications of the Ethernet LAN interface card.5.4 WAN Interface CardThis section describes the types, functions, applications, appearance, interfaces, and technicalspecifications of the WAN interface card.5.5 Voice Interface CardThis section describes the types, functions, applications, appearance, interfaces, and technicalspecifications of the voice interface card.5.6 xDSL Interface CardThis section describes the types, functions, applications, appearance, interfaces, and technicalspecifications of the xDSL/xPON interface card.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.25

5.1 IntroductionThis section describes the cards supported by the AR routers, including card types, relationshipsbetween cards, the interface numbering scheme, and card dimensions.5.1.1 Relationships Between CardsThis section describes the relationships between the cards supported by the AR routers.NOTElOn the AR1200, the backplane is at the bottom of the chassis, and cards are installed on the backplane.lOn the AR2220, the backplane is in the middle of the chassis, cards are installed on the rear side of thebackplane, and a power supply module is installed on the front side of the backplane.lOn the AR2240, the backplane is in the middle of the chassis, cards are installed on the front and rearsides of the backplane, and a power supply unit is installed on the front side of the backplane.lOn the AR3260, the backplane is in the middle of the chassis, cards are installed on the front and rearsides of the backplane, and a power supply unit is installed on the front side of the backplane.Figure 5-1 and Figure 5-2 illustrates the relationships between the cards supported by the ARrouters.NOTElOn the AR1200–S, the backplane is at the bottom of the chassis, and cards are installed on the backplane.lOn the AR2220–S, the backplane is in the middle of the chassis, cards are installed on the rear side ofthe backplane, and a power supply module is installed on the front side of the backplane.Figure 5-1 Relationships between cards on the AR1200-SService cardPowerBackplaneSRU FanService card Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.26

Figure 5-2 Relationships between cards on the AR2220-SPowerBackplaneSRUFanService cardService card 5.1.2 Interface NumberingThis section describes the interface numbering scheme on the AR routers.On the AR routers, interfaces are numbered in the format of slot ID/subcard ID/interfacesequence number.lSlot IDThe slot ID specifies the ID of the slot where a card resides.–The SRU of the AR1200-S and 2220-S is integrated with the chassis, so the slot ID isfixed as 0.–When slots need to be combined into one slot, the greater slot ID is used as the new slotID. For example, when slot 1 and slot 2 are combined, slot ID 2 is used as the new slotID.lSubcard IDThe subcard ID specifies the ID of a subcard. The cards of AR routers series routers do notsupport subcards. Therefore, the subcard ID of the AR routers is fixed as 0.lInterface sequence numberThe interface sequence number indicates the number of each interface on a card.–There is only one row of interfaces on the interface card. These interfaces are numberedfrom left to right starting with 0.0 1 2 3–There are two rows of interfaces on the interface card. These interfaces are numberedfrom bottom to top and left to right starting with 0.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.27

135791102468105.1.3 Card DimensionsThis section explains the conventions for measuring cards and lists the dimensions of SIC, WSIC,XSIC card.Figure 5-3 illustrates the dimensions of a card.Figure 5-3 Card dimensions descriptionWidthDepthHeight NOTEThe card dimensions are defined as follows:lDepth: the distance between the handle and the end of Printed Circuit Board (PCB)lWidth: the longest distance between the tops of two handleslHeight: the height of the ejector leverFigure 5-4 shows the cards supported by the AR routers and Table 5-1 lists the card dimensions.Figure 5-4 Card appearancesSICWSICXSIC Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.28

Table 5-1 Card dimensionsCard Type Dimensions (Depth x Width x Height)SIC card 223.5 mm x 100.1 mm x 19.82 mm (8.8 in. x 3.94 in. x 0.78in.)WSIC card 223.5 mm x 201 mm x 19.82 mm (8.8 in. x 7.92 in. x 0.78in.)XSIC card 223.5 mm x 201 mm x 40.14 mm (8.8 in. x 7.92 in. x 1.58in.) 5.2 WLAN SubcardWLAN subcards are Wi-Fi modules.5.2.1 Functions and ApplicationsFunctionslWLAN subcards provide Wi-Fi interfaces. Wi-Fi interfaces comply with IEEE 802.11n,802.11g, and 802.11b, and each of these interfaces provides a maximum of 300 Mbit/stransmission rate.lWLAN subcards provide a high wireless performance and reliability, and large coveragescope using the multiple-input and multiple-output (MIMO) technology.lWLAN subcards support 64/128/152-bit WEP encryption, WPA/WPA2 encryption, andWPA-PSK/WPA2-PSK encryption to provide secure data transmission.ApplicationsA WLAN subcard has a dedicated WLAN slot on the AR routers.5.2.2 Technical SpecificationsTable 5-2 describes the technical specifications of the WLAN subcard.Table 5-2 Technical specifications of the WLAN subcardItem SpecificationMaximum powerconsumption7.24 W 5.3 Ethernet LAN Interface CardThis section describes the types, functions, applications, appearance, interfaces, and technicalspecifications of the Ethernet LAN interface card.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.29

5.3.1 8FE1GE-8-Port 100BASE-RJ45 and 1-Port 1000BASE-RJ45 L2/L3 Ethernet Interface CardThe 8FE1GE is the 8-port 100M+1-port 1000M Ethernet electrical interface card (RJ45). Itimplements the 9-channel Ethernet Layer 2 and Layer 3 switching functions.Functions and ApplicationsFunctionsThe 8FE1GE provides eight FE electrical interfaces and one GE electrical interface to implementdata access and line-speed switching.lWhen category 5 twisted pairs (straight-through cables or crossover cables) are used, themaximum transmission distance is 100 meters.lWhen category 5 twisted pairs (straight-through cables or crossover cables) are used, 100Mbit/s line-speed forwarding is supported between the eight FE interfaces.lThe eight FE interfaces work at 10 Mbit/s or 100 Mbit/s, in auto-sensing mode. The GEinterface works at 10/100/1000 Mbit/s, in auto-sensing mode.lThese interfaces support the half duplex mode and full duplex mode. The full duplex modeis most commonly used.ApplicationsThe 8FE1GE can be installed into the WSIC slots of the AR1200-S and AR2220-S, On theAR1200-S, two SIC slots are combined into one WSIC slot.Panel and InterfacesFigure 5-5 shows the appearance of the 8FE1GE.Figure 5-5 Appearance of the 8FE1GE31a b2 Buttons and Indicators on the PanelTable 5-3 describes the buttons and indicators on the 8FE1GE panel.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.30

Table 5-3 Buttons and indicators on the 8FE1GE panelNumberin Figure5-5Indicator Color Description1STAT Green If the indicator blinks once 2s (0.5 Hz),the system is running properly.If the indicator blinks once 0.25s (4Hz), the system is powering on orrestarting.Red If the indicator is red, a fault that affectsservices occurs and cannot be rectifiedautomatically. The fault needs to berectified manually.Off If the indicator is off, the software is notrunning or is being reset.2 and 3 FE/GE interfaceindicators:lThe LINKindicator is ingreen.lThe ACTindicator is inyellow.Green If the indicator is steady on, a link hasbeen established.If the indicator is off, no link isestablished.Yellow If the indicator is blinking, data is beingtransmitted or received.If the indicator is off, no data is beingtransmitted or received. InterfacesTable 5-4 describes the types and functions of interfaces on the 8FE1GE.Table 5-4 Types and functions of interfaces on the 8FE1GELetter inFigure5-5Name QuantityDescription Cable Typea 10BASE-TX/100BASE-TX electricalinterface8 The 8FE1GE provideseight FE electricalinterfaces to transmit andreceive FE services.6.5 Network Cableb1000BASE-Telectricalinterface1 The 8FE1GE provides oneGE electrical interface totransmit and receive GEservices. Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.31

Interface AttributesTable 5-5 Attributes of 10BASE-TX/100BASE-TX electrical interfacesItem DescriptionConnector type RJ45Interface attribute MDI/MDIXNOTElThe interfaces of most network cards are medium dependent interfaces(MDIs).lMDIX interfaces are usually used on hubs or LAN switches.StandardscomplianceIEEE802.3, IEEE802.3u, IEEE802.3abFrame format Ethernet_II, Ethernet_SAP, or Ethernet_SNAPNetwork layerprotocolIP Table 5-6 Attributes of 1000BASE-T electrical interfacesItem DescriptionConnector type RJ45Interface attribute MDI/MDIXNOTElThe interfaces of most network cards are medium dependent interfaces(MDIs).lMDIX interfaces are usually used on hubs or LAN switches.StandardscomplianceIEEE802.3, IEEE802.3u, IEEE802.3abFrame format Ethernet_II, Ethernet_SAP, or Ethernet_SNAPNetwork layerprotocolIP Technical SpecificationsTable 5-7 describes the technical specifications of the 8FE1GE.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.32

Table 5-7 Technical specifications of the 8FE1GEItem SpecificationDimensions(depth x width xheight)223.5 mm x 201 mm x 19.82 mm (8.8 in. x 7.92 in. x 0.78 in.)Maximum powerconsumption12.036 WWeight 0.6 kg (1.33 lb) 5.3.2 24GE-24-Port 1000BASE-RJ45 L2/L3 Ethernet Interface CardThe 24GE is the 24-port 1000M Ethernet electrical interface card (RJ45). It implements the 24-channel Ethernet Layer 2 and Layer 3 switching functions.Functions and ApplicationsFunctionsThe 24GE provides 24 GE electrical interfaces to implement data access and line-speedswitching.lWhen category 5 twisted pairs (straight-through cables or crossover cables) are used, themaximum transmission distance is 100 meters.lWhen category 5 twisted pairs (straight-through cables or crossover cables) are used, 1000Mbit/s line-speed forwarding is supported between the 24 GE interfaces.lThese interfaces work in 10/100/1000 Mbit/s auto-sensing mode.lThese interfaces support the half duplex mode and full duplex mode. The full duplex modeis most commonly used.ApplicationsThe 24GE can be installed into the XSIC slot on the AR2220-S. On the AR2220-S, two WSICslots are combined into one XSIC slot.Panel and InterfacesFigure 5-6 shows the appearance of the 24GE.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.33

Figure 5-6 Appearance of the 24GE1a232323232323232323232323 Buttons and Indicators on the PanelTable 5-8 describes the buttons and indicators on the 24GE panel.Table 5-8 Buttons and indicators on the 24GE panelNumber inFigure 5-6Indicator Color Description1STAT Green If the indicator blinks once 2s (0.5Hz), the system is running properly.If the indicator blinks once 0.25s (4Hz), the system is powering on orrestarting.Red If the indicator is red, a fault thataffects services occurs and cannot berectified automatically. The faultneeds to be rectified manually.Off If the indicator is off, the software isnot running or is being reset.2: indicators ofinterfaces in thesecond rowLINK Green If the indicator is steady on, a linkhas been established.3: indicators ofinterfaces in thefirst rowIf the indicator is blinking, data isbeing transmitted or received.If the indicator is off, the link is notconnected. InterfacesTable 5-9 describes the types and functions of interfaces on the 24GE.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.34

Table 5-9 Types and functions of interfaces on the 24GELetter inFigure 5-6Name QuantityDescription Cable Typea 1000BASE-T electricalinterface24 The 24GE provides 24GE electrical interfaces totransmit and receive GEservices.6.5 Network Cable Interface AttributesTable 5-10 Attributes of 1000BASE-T electrical interfacesItem DescriptionConnector type RJ45Interface attribute MDI/MDIXNOTElThe interfaces of most network cards are medium dependent interfaces(MDIs).lMDIX interfaces are usually used on hubs or LAN switches.StandardscomplianceIEEE802.3, IEEE802.3u, IEEE802.3abFrame format Ethernet_II, Ethernet_SAP, or Ethernet_SNAPNetwork layerprotocolIP Technical SpecificationsTable 5-11 describes the technical specifications of the 24GE.Table 5-11 Technical specifications of the 24GEItem SpecificationDimensions(depth x width xheight)223.50 mm x 201.00 mm x 40.14 mm (8.8 in. x 7.92 in. x 1.58 in.)Maximum powerconsumption25 WWeight 0.85 kg (1.88 lb) Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.35

5.4 WAN Interface CardThis section describes the types, functions, applications, appearance, interfaces, and technicalspecifications of the WAN interface card.5.4.1 1GEC (1-Port-GE Combo WAN Interface Card)1GEC is a 1-port 1000M Ethernet optical and electrical Combo interface card (RJ45, SFP). Onlyone of the optical interface and electrical interface can be used at a time.1GEC stands for:l1: one interfacelGE: 1000M EthernetlC: Combo interfaceFunctions and ApplicationsFunctionsThe 1GEC provides one GE optical and electrical Combo interface to implement data accessand line-speed switching.lThe Combo interface sends, receives, and processes GE data traffic.lThe electrical interface works at 10/100/1000 Mbit/s in auto-sensing mode.lThe optical interface works at 100/1000 Mbit/s in auto-sensing mode.ApplicationsThe 1GEC is installed into the SIC slot of the AR1200-S and AR2220-S.Panel and InterfacesFigure 5-7 shows the appearance of the 1GEC panel.Figure 5-7 Appearance of the 1GEC panel12 3 4 5a b Buttons and Indicators on the PanelTable 5-12 describes the buttons and indicators on the 1GEC panel.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.36

Table 5-12 Buttons and indicators on the 1GEC panelNumberinFigure5-7Indicator Color Description1STAT Green If the indicator blinks once 2s (0.5 Hz),the system is running properly.If the indicator blinks once 0.25s (4 Hz),the system is powering on or restarting.Red If the indicator is red, a fault that affectsservices occurs and cannot be rectifiedautomatically. The fault needs to berectified manually.Off If the indicator is off, the software is notrunning or is being reset.2 and 3 GE interfaceindicators:lThe LINKindicator is ingreen.lThe ACTindicator is inyellow.Green If the indicator is steady on, a link hasbeen established.If the indicator is off, no link isestablished.Yellow If the indicator is blinking, data is beingtransmitted or received.If the indicator is off, no data is beingtransmitted or received.4 and 5 SFP interfaceindicators:lThe LINKindicator is ingreen.lThe ACTindicator is inyellow.Green If the indicator is steady on, a link hasbeen established.If the indicator is off, no link isestablished.Yellow If the indicator is blinking, data is beingtransmitted or received.If the indicator is off, no data is beingtransmitted or received. InterfacesTable 5-13 describes the types and functions of interface on the 1GEC.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.37

Table 5-13 Types and functions of the interface on the 1GECLetter inFigure 5-7Name QuantityDescription Cable Typea 1000BASE-Telectricalinterface1 The 1GEC provides one GE electricalinterface to transmit and receive GE services.NOTEOnly one of the optical interface and electricalinterface can be used at a time.6.5 NetworkCableb 1000BASE-Xopticalinterface1 The 1GEC provides one GE optical interfaceto transmit and receive GE services.6.6 OpticalFiber Interface AttributesTable 5-14 Attributes of 1000BASE-T electrical interfacesItem DescriptionConnector type RJ45Interface attribute MDI/MDIXNOTElThe interfaces of most network cards are medium dependent interfaces(MDIs).lMDIX interfaces are usually used on hubs or LAN switches.StandardscomplianceIEEE802.3, IEEE802.3u, IEEE802.3abFrame format Ethernet_II, Ethernet_SAP, or Ethernet_SNAPNetwork layerprotocolIP Table 5-15 Attributes of the SFP optical module (100/1000 Mbit/s) supported by the GE opticalinterfaceAttributeDescriptionTransmissiondistance500 m 10 km 10 km (single-mode bidirectionalfiber)40 km 40 km 80 km 100 kmHuawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.38

AttributeDescriptionCenterwavelength850 nm 1310nmTx:1310nmRx:1490nmTx:1490nmRx:1310nm1310nm1550nm1550nm1550nmTransmittingpower-9.5dBm to-2.5dBm-9.0dBm to-3.0dBm-9.0dBm to-3.0dBm-9.0dBm to-3.0dBm-5.0dBm to0 dBm-5.0dBm to0 dBm-2.0dBm to5.0dBm0 dBmto 5dBmReceiversensitivity-17.0dBm-20.0dBm-19.5dBm-19.5dBm-23dBm-22dBm-23.0dBm-30.0dBmOverloadopticalpower0 dBm -3.0dBm-3.0dBm-3.0dBm-3.0dBm-3.0dBm-3.0dBm-9.0dBmExtinctionratio9 dB 9 dB 6 dB 6 dB 9 dB 8.5 dB 9 dB 8 dBFibertypeMulti-modeSingle-mode Technical SpecificationsTable 5-16 describes the technical specifications of the 1GEC.Table 5-16 Technical specifications of the 1GECItem SpecificationDimensions(depth x width xheight)223.5 mm x 100.1 mm x 19.82 mm (8.8 in. x 3.94 in. x 0.78 in.)Maximum powerconsumption2.28 WWeight 0.25 kg (0.55 lb) Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.39

5.4.2 2FE-2-Port-FE WAN Interface CardThe 2FE is the 2-port 100M Ethernet electrical interface card (RJ45).Functions and ApplicationsFunctionsThe 2FE provides two FE electrical interfaces to implement data access and line-speedswitching.lWhen category 5 twisted pairs (straight-through cables or crossover cables) are used, themaximum transmission distance is 100 meters.lTwo FE electrical interfaces can be bound to function as an upstream interface at the linerate of 200 Mbit/s.lThe two FE interfaces work in 10/100 Mbit/s auto-sensing mode.lThese interfaces support the half duplex mode and full duplex mode. The full duplex modeis most commonly used.ApplicationsThe 2FE can be installed into the SIC slot of the AR1200-S, AR2220-S.Panel and InterfacesFigure 5-8 shows the appearance of the 2FE.Figure 5-8 Appearance of the 2FE12 3a Buttons and Indicators on the PanelTable 5-17 describes the buttons and indicators on the 2FE panel.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.40

Table 5-17 Buttons and indicators on the 2FE panelNumber inFigure 5-8Indicator Color Description1STAT Green If the indicator blinks once 2s (0.5Hz), the system is running properly.If the indicator blinks once 0.25s (4Hz), the system is powering on orrestarting.Red If the indicator is red, a fault thataffects services occurs and cannot berectified automatically. The faultneeds to be rectified manually.Off If the indicator is off, the software isnot running or is being reset.2 and 3 FE interfaceindicators:lThe LINKindicator isin green.lThe ACTindicator isin yellow.Green If the indicator is steady on, a linkhas been established.If the indicator is off, no link isestablished.Yellow If the indicator is blinking, data isbeing transmitted or received.If the indicator is off, no data is beingtransmitted or received. InterfacesTable 5-18 describes the types and functions of interfaces on the 2FE.Table 5-18 Types and functions of interfaces on the 2FELetterinFigure5-8Name QuantityDescription Cable Typea FE electricalinterface2 The 2FE provides two FEelectrical interfaces to transmitand receive FE services.6.5 NetworkCable Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.41

Interface AttributesTable 5-19 Attributes of 10BASE-TX/100BASE-TX electrical interfacesItem DescriptionConnector type RJ45Interface attribute MDI/MDIXNOTElThe interfaces of most network cards are medium dependent interfaces(MDIs).lMDIX interfaces are usually used on hubs or LAN switches.StandardscomplianceIEEE802.3, IEEE802.3u, IEEE802.3abFrame format Ethernet_II, Ethernet_SAP, or Ethernet_SNAPNetwork layerprotocolIP Technical SpecificationsTable 5-20 describes the technical specifications of the 2FE.Table 5-20 Technical specifications of the 2FEItem SpecificationDimensions(depth x width xheight)223.5 mm x 100.1 mm x 19.82 mm (8.8 in. x 3.94 in. x 0.78 in.)Maximum powerconsumption3.01 WWeight 0.3 kg (0.66 lb) 5.4.3 1E1T1-M/2E1T1-M-1/2 Port-Channelized E1/T1/PRI/VE1Multifunctional Interface CardThe 1E1T1-M/2E1T1-M is the E1/T1/PRI/VE1 processing unit on the AR routers and providesone or two E1/T1/PRI/VE1 interfaces. Primary Rate Interface (PRI) indicates ISDN primaryrate interfaces.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.42

NOTEl1/2: indicates one or two interfaces.lE1: indicates E1 interfaces.lT1: indicates T1 interfaces.lM: indicates multiflex trunks.lVE1: indicates voice E1 interfaces.Table 5-21 lists the number of interfaces on the 1E1T1-M and 2E1T1-M.Table 5-21 Number of interfaces on the 1E1T1-M and 2E1T1-MCard Name Quantity of Interfaces1E1T1-M 12E1T1-M 2 2E1T1-M cards have two types: SIC and WSIC. Table 5-22 lists the slots where the SIC cardand WSIC card are installed.Table 5-22 Slots of 2E1T1-M SIC and WSIC cardsCard Slot2E1T1-M (SIC) SIC slot2E1T1-M (WSIC) WSIC slot or XSIC slotNOTEIn an XSIC slot, the WSIC card is installed in the lower partof the slot. The WSIC card uses the XSIC slot ID as its ownslot ID. Functions and ApplicationsFunctionsThe 1E1T1-M/2E1T1-M provides the following functions:lSends, receives, and processes E1/T1 data traffic.lProvides CE1/T1 access.lProvides the ISDN PRI function.Applications1E1T1-M/2E1T1-M(SIC) can be installed into the SIC slot of the AR1200-S and AR2220-S.2E1T1-M(WSIC) is installed in a WSIC or XSIC slot on the AR2220-S.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.43

Panel and InterfacesFigure 5-9 shows the appearance of the 1E1T1-M.Figure 5-9 Appearance of the 1E1T1-M1 2a Figure 5-10 shows the appearance of the 2E1T1-M (SIC).Figure 5-10 Appearance of the 2E1T1-M (SIC)1a2 Figure 5-11 shows the appearance of the 2E1T1-M (WSIC).Figure 5-11 Appearance of the 2E1T1-M (WSIC)1a2 Buttons and Indicators on the PanelTable 5-23 describes the buttons and indicators on the 1E1T1-M/2E1T1-M panel.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.44

Table 5-23 Buttons and indicators on the 1E1T1-M/2E1T1-M panelNumber inFigure 5-9,Figure 5-10,Figure 5-11Indicator Color Description1STAT Green If the indicator blinks once 2s (0.5Hz), the system is running properly.If the indicator blinks once 0.25s (4Hz), the system is powering on orrestarting.Red If the indicator is red, a fault thataffects services occurs and cannot berectified automatically. The faultneeds to be rectified manually.Off If the indicator is off, the software isnot running or is being reset.2 LINK/ACT Green If the indicator is steady on, a linkhas been established.Yellow (Theindicator is ingreen and blinksred.)If the indicator is in green and blinksred, data is being transmitted orreceived.Off If the indicator is off, there is noconnection. InterfacesTable 5-24 describes the types and functions of interfaces on the 1E1T1-M/2E1T1-M.Table 5-24 Types and functions of interfaces on the 1E1T1-M/2E1T1-MLetter inFigure 5-9,Figure5-10,Figure 5-11NameQuantity Description Cable Typea DB9 1E1T1-M: 12E1T1-M: 275-ohm or 120-ohm E1 cable or100-ohm T1cable6.7 E1/T1 Trunk Cables Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.45

Interface AttributesTable 5-25 Attributes of channelized E1 interfacesAttribute DescriptionConnector type DB9StandardscomplianceG.703 or G.704Transmission rate 2.048 Mbit/sCable type E1 75-ohm unbalanced coaxial cableE1 120-ohm balanced twisted pair cableE1 trunk cable extensionWorking mode CE1, ISDN PRI, or VE1Function BackupTerminal accessISDN PRI Table 5-26 Attributes of channelized T1 interfacesAttribute DescriptionConnector type DB9StandardscomplianceG.703 or G.704Transmission rate 1.544 Mbit/sCable type T1 100-ohm coaxial cableWorking mode CT1, ISDN PRI, or VT1Function BackupTerminal accessISDN PRI Technical SpecificationsTable 5-27 describes the technical specifications of the 1E1T1-M/2E1T1-M.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.46

$Table 5-27 Technical specifications of the 1E1T1-M/2E1T1-MItem SpecificationDimensions(depth x width xheight)1E1T1-M/2E1T1-M (SIC): 223.5 mm x 100.1 mm x 19.82 mm (8.8 in.x 3.94 in. x 0.78 in.)2E1T1-M (WSIC): 223.5 mm x 201 mm x 19.82 mm (8.8 in. x 7.92 in.x 0.78 in.)Maximum powerconsumption7 WWeight 0.3 kg (0.66 lb) 5.4.4 1E1T1-F/2E1T1-F (1/2-Port-Fractional Channelized E1/T1WAN Interface Card)The 1E1T1-F/2E1T1-F is the E1/T1 processing unit on the AR routers and provides one or twoE1/T1 interfaces.NOTE1E1T1-F/2E1T1-F stands for:l1/2: one or two interfaceslE1: E1 interfacelT1: T1 interfacelF: fractional E1Table 5-28 lists the number of interfaces on the 1E1T1-F and 2E1T1-F.Table 5-28 Number of interfaces on the 1E1T1-F and 2E1T1-FCard Name Quantity of Interfaces1E1T1-F 12E1T1-F 2 Functions and ApplicationsFunctionsThe 1E1T1-F/2E1T1-F sends, receives, and processes E1/T1 data traffic. Table 5-29 describesthe differences in functions provided by the 1E1T1-F/2E1T1-F and 1E1T1-M/2E1T1-M.Huawei AR1200-S&2200-S Series Enterprise RoutersHardware Description 5 CardsIssue 03 (2012-04-20) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.47$

Huawei Technologies EM820W HSPA+ Module User Manual Hardware Description

Huawei Technologies Co.,Ltd HSPA+ Module Hardware Description

Contents

User manual II

Navigation menu

Namespaces

Views

Navigation