Huawei Technologies H3CSOHOWDR814G ADSL2+ 802.11b/g Wireless Router User Manual DWG 814E menual

Download:
Mirror Download [FCC.gov]
Document ID	536747
Application ID	YPLrvN0RRiLVtAmVdRSUNQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	51.08kB (638497 bits)
Date Submitted	2005-04-27 00:00:00
Date Available	2005-04-27 00:00:00
Creation Date	2005-04-01 06:31:50
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2005-04-25 17:29:55
Document Title	Microsoft Word - DWG-814E menual.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	admin

DWG Series ADSL2+ Router Quick
Installation Manual
LED
Power
Link
Telephone port
ADSL2+ Wireless Router
Diag
Appearance
LINE
Splitter
ADSL
Desktop PC
PHONE
NoteBook
Telephone
Figure 2 Installing ADSL Line
Figure 1 DWG series rear view
Packing List
One DWG series ADSL2+ router
One power adapter
One telephone cable
One Ethernet cable
One USB cable
Two screws and two anchors
One Quick Installation Manual
One CD
Certificate of Quality
Hardware Installation
3.1 Installing ADSL Line
LAN
Normal status
The LED stays green. Check the power cord connection if the LED stays off.
The blinking of the LED indicates the ADSL activation and 20 to 30 seconds later,
the LED stays green.
The green LED stays on. The blinking of the green LED indicates the data
transmission on the Ethernet port.
This LED is off. If this LED turns on, contact the agents for help.
Two options are available for ADSL line connections:
Direct connect the ADSL line (same as a regular telephone port) to
the wall telephone line outlet.
As shown in Figure 2 , Connect the ADSL port and a telephone set
to a splitter, and then the splitter to the wall outlet of telephone line.
Thus you may place phone calls when accessing the Internet.
3.2 Connecting to PC or Ethernet
You can use crossover or straight through cables to connect the PC, HUB, or
switch to the MDI/MDIX auto-sensing interface of WDR series ADSL2+ router.
3.3 Connecting the Power Cord
(1) Attach one end of the power cord to the router and the other end to power
outlet. The power cord is accessory of the router.
(2) Observe the LED status one minute later. The following table lists the LEDs
and their normal expected status.
Table 1 LEDs
3.4 Configuring to Obtain an IP Address Automatically
Take the operation in the Windows 2000/XP operating system for example. The
steps are as follows:
(1) Click the  button and choose the Settings > Control Panel options.
Double-click on the Network Dial-up Connections icon from the Control Panel
window.
(2) Right-click on the Local Area Connection icon and select the Properties from
the pop-up menu. Next, choose the Internet Protocol (TCP/IP) from the Local
Area Connection Properties tabbed interface and click  to proceed.
(3) When the Internet Protocol (TCP/IP) Properties interface pops up, select the
Obtain an IP address automatically and Obtain DNS server address
automatically options, then click .
3.5 Logon
(1) Check the configuration of the proxy server. Disable the proxy server first
when the PC is accessing the Internet through proxy server.
(2) Use the Web browser. Enter http://192.168.1.1 in the address bar (by default,
the IP address of the WDR ADSL2+ router is 192.168.1.1).
(3) Log onto the Web setup manager. A new window appears prompting you to
enter the user name and password. For the first logon, use the default
administrator user name admin with the password admin. The password can be
modified after entering the management interface.
(2) Click  from the Navigation bar to enter the Status tabbed page. You
can find that the IP Address item presents an IP address of the public network
instead of the original 0.0.0.0.
Quick Troubleshooting
Table 2 Quick troubleshooting
Symptom
Solution
The ADSL
Link LED
stays OFF.
The RJ-11 telephone cable must be used and connected to the ADSL and
telephone ports correctly.
Make sure that:
Figure 5 Checking status
Figure 3 Entering the user name and password
Setup
(3) If you obtain no public IP address, click  from the Navigation
bar. Then you can view the VPI/VCI value that the system detects automatically.
If the values are incorrect, select the Disable option and input the values
manually. For the correct VPI/VCI value, contact your local ISP.
After you log onto the Web page, follow the simple steps to finish the quick
configuration:
(1) Click  from the Navigation bar to the Quick Start window.
Select the PPPoE as the login type, and then input the user name and password
assigned by ISP. You may leave the Service Name box untouched. Then click
 to proceed.
Figure 6 Checking the VPI/VCI value
Input the username
and password
assigned by ISP
At last, click  in the WAN tabbed interface to finish the
configuration.
Figure 7 Save settings
Figure 4 Setting parameters
Access to
the Internet
fails.
You forget
the login
password.
Access to
the router
Web pages
fails.
The
modification
on the Web
pages fails
to save.
1) You have followed all the steps described above and found no
problems.
2) The IP address of your PC is in the range of allocated valid addresses.
To check it, select the Run option from the Start menu. In the pop-up
window, input winipcfg (in Win98 operating system) or ipconfig (in
Win2000/XP operating system) for the IP address checking.
3) You can ping the IP address of the gateway (192.168.1.1).
4) You have performed the correct DNS configuration on your PC.
5) You have disabled the proxy server.
6) The correct VPI/VCI value is set on the WAN Setup window.
Both of the default user name and password are admin. If you have
changed the password but forget it, press the Reset button for 5 seconds
to restore the default settings on the router. Then you can access the Web
page with the default user name and password.
Note: The reset function restores the settings to the factory default
settings.
Make sure that:
1) The LAN LED is ON.
2) The settings of TCP/IP properties are correct.
3) You have entered the correct user name and password.
If you still cannot access the router Web pages, press the Reset button for
5 seconds to restore the default settings.
You need to click  to save every modification that you
have made.
FCC Caution:
1. This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
2. This device and its antenna(s) must not be co-located or operating in conjunction
with any other antenna or transmitter.
3. Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user authority to operate the equipment.
4. This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
5. This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 20 centimeters between the radiator and your body.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2005:04:01 06:31:50Z
Modify Date                     : 2005:04:25 17:29:55+08:00
Page Count                      : 3
Creation Date                   : 2005:04:01 06:31:50Z
Mod Date                        : 2005:04:25 17:29:55+08:00
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : admin
Metadata Date                   : 2005:04:25 17:29:55+08:00
Creator                         : admin
Title                           : Microsoft Word - DWG-814E menual.doc
Has XFA                         : No

EXIF Metadata provided by EXIF.tools