Huawei Technologies HG8245Q GPON Terminal User Manual 15 EchoLife HG8245Q UserMan

Huawei Technologies Co.,Ltd GPON Terminal 15 EchoLife HG8245Q UserMan

Contents

15_EchoLife HG8245Q UserMan.pdf

Quick StartEchoLife HG8245Q GPON Terminal
1Safety PrecautionsTo use the device properly and safely, read the safety precautions carefully before using the device and strictly observe these precautions when using the device. Do not look directly into the optical port without eye protection. Keep the device out of the reach of children as the components or accessories may be swallowed. The power supply voltage of the device must meet the requirements on the input voltage of the device. Do not use any power adapters that are not in the standard conguration. Otherwise, the device may be abnormal or unsafe. If the power adapter is damaged and its internal circuit is exposed due to man-made factors, do not touch the exposed circuit, which may bring safety risks. Prevent objects, such as metal, from entering the device through the heat dissipation hole. Dry your hands before connecting or disconnecting cables. Stop the device and switch off the power before connecting or disconnecting cables. Switch off the power and disconnect all cables, including the power cable, optical ber, and network cable, during periods of lightning activities. The socket-outlet shall be installed near the power adapter and shall be easily accessible. Before use the power adapter, please check no damage on the adapter.  Do not lead the strength member of the optical ber or other metal parts indoors. Do not install telephone lines, network cables, power adapters or power adapter cables outdoors. Adopting these measures will help prevent device damage and bodily injuries which are especially prone during thunderstorms. Install the device according to the requirements of the manufacturer. To be specic, reserve at least 10 cm for heat dissipation at the top and four sides of the device, keep the device away from ammable objects, highly magnetic or electric devices, such as microwave ovens, refrigerators, and mobile phones. Do not place any object on the device, so that the device will not be damaged due to overheating or deformation. If an abnormality occurs, for example, liquid entering the device, smoke, unusual sound, and smell, stop the device immediately, switch off the power, disconnect all cables (such as the power cable, optical cable, and network cable) to the device, and contact the authorized service center. Do not disassemble the device without permission. In the case of a device fault, contact the authorized service center. Dispose of the packing materials, expired batteries, and old or abandoned devices in accordance to local laws and regulations (recycling them is strongly recommended). Do not change the structure, safety design, or performance design of the device without prior authorization.Safety precautions:Fireproof precautions: Keep the device away from large heat source equipment, bare ames, and high-power devices, such as electric heaters, candles, and blow drier, to eliminate safety risks. If there are aged cables or power socket facilities on the power supply line to or near the device, replace them in time to eliminate safety risks. The power supply voltage of the device must meet the input voltage requirement.
Technical SpecicationsItem  SpecicationsDimensions (L x W x H) 230 mm x 190 mm x 30 mm(excluding the support)Weight (including the power adapter) About 500gPower supply See the nameplate on the device.Power adapter input 100-240 V AC, 50-60 HzMaximum power consumption ≤18.5 WAmbient temperature 0ºC - +40ºCAmbient humidity 5% RH -95% RH (non-condensing)Installing the GPON TerminalCaution1. Do not install the GPON terminal outdoors or on the outdoor cabinet.2. Do not install GPON terminal in other modes, such as the ceiling.3.The terminal cannot be connected to other devices such as GPON terminals, switch and router.HG8245Q is equipped with a support by default. The following figure shows a vertically-placed HG8245Q.NOTEThe appearance shown in this document may be different from the actual appearance of the product. The actual product provided by the carrier prevails.2
1Reset2Ethernet port3POTS port4USB port5Power port6Optical portConnecting Cables32154Optical portPC Power socketUSB storage device36IP STBTV set
47 WLAN switch8 WPS switchStep 1 Use an optical fiber to connect the OPTICAL port on the GPON terminal to the optical port in the wall. NOTE1.The type of the optical connector connected to the optical port in the wall is determined by practical conditions.2.To ensure normal use of bers, make sure that the ber bend radius is larger than 30 mm.87Wi-Fi terminal
5Step 3 Use a phone line to connect the TEL port to a phone or fax machine.Step 4 Use a USB data cable to connect the USB port to the USB storage device.Step 5Use a power adapter to connect the POWER port to the power socket.Step 6 Press the WLAN switch to enable the Wi-Fi access function. By default, this function is enabled.Step 7 Press the WPS switch to enable the WPS encryption function.NOTE- If you do not perform any operations after logging in to the system for ve minutes, you will exit the system and the system automatically returns to the login interface.- The system will be locked if you input incorrect user name and password three consecutive times. One minute later, it will be unlocked. - Change the initial password after logging in to the web page.Step 2 Use a network cable to connect the LAN port to a PC or the Ethernet port on the IP STB.NOTEBefore enabling the WPS encryption function of a GPON terminal, ensure that the function is set in the system software in advance. After successful setting, press the WPS switch for the settings to take effect.Logging in to the Web Conguration WindowStep 1 Set the IP address of the PC in the same subnet as the management IP address of the GPON terminal. Step 2 Enter the management IP address of the PON terminal in the address bar of Internet Explorer and press Enter.            The login window is displayed. Step 3 In the login window, select your preferred language, enter the user name and password ( printed on the nameplate of the device.), and click Login. After the password is authenticated, the Web configu    indow is displayed. NOTEYou can nd the default management IP address on the nameplate of the device.
HG8245Q supporting Wi-Fi, a wireless network coverage is subject to the number, thickness, and positions of walls, materials, ceilings, or other objects that radio signals traverse. Besides, metarial type and background radio frenquency (RF) noise also affect the coverage of a wireless network. You can maximize the coverage of a wireless network using the following methods:1. Decrease the number of walls and ceilings between HG8245Q and other network devices.Each wall or ceiling reduces the coverage of a wireless network by one to 30 meters. Install HG8245Q at a proper place to avoid walls or ceilings whenever possible.2. Observe the straight line rule when installing network devices.The distance for which signals have to traverse at a 45° corner of two 0.5 meter-thick walls reaches approximately one meter. To better receive signals, devices should be installed at places where signals can directly traverse walls or ceilings.3. Note the impact of building materials on the wireless network coverage.A metal door or aluminum wall may limit the coverage of a wireless network. Install access points, wireless routers, and computers, so signals can traverse walls or open passageways. Materials and objects such as FRP products, metal products, insulative walls, filing cabinets, bricks, and concrete weaken radio signals.4. When connecting ONT (such as HG8245Q) to a wireless network, keep it far from the following devices: - Electronic devices or components that produce RF noises (keep a distance of more than 2 meters between such a device and HG8245Q.)- 2.4 GHz wireless mobile phones or X-10 devices (such as microwave ovens, home security systems, blue-tooth devices, and refrigerators) that greatly weaken or even eliminate radio signals. Even if a 2.4 GHz wireless mobile phone is not connected to a wireless network, the phone base still sends signals that interfere the wireless network.NOTEConguring Wi-Fi ParametersStep 1 Choose the WLAN tab and choose WLAN Basic Configuration. Step 2 In the pane, select the Enable WLAN option box. In the dialog box that is displayed, set the basic Wi-Fi parameters, including the SSID, authentication mode, and encryption mode. Step 3 Click Apply.-SSID Name: See the nameplate on the device.-WPA PreSharedKey: See the nameplate on the device.SSID indicates the name of a wireless network searched by the Wi-Fi terminal; WPA indicates the authentication password for the Wi-Fi terminal to access a wireless network. 6
7FCC StatementFCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution! Any changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
8Indicator DescriptionTable 1 Indicator status description 1  Indicator    Status   DescriptionUSBSteady on The USB port is connected and is working in the host mode, but no data is transmitted.Blinks twice a second Data is being transmitted on the USB port.Off The system is not powered on or the USB port is not connected.WPSSteady on The WPS function is enabled.Blinking A Wi-Fi terminal is accessing the system.Off The WPS function is disabled.WLANSteady on The WLAN function is enabled.Blinking Data is being transmitted on the WLAN port.Off The WLAN function is disabled.LAN1– LAN4Steady on The Ethernet connection is in the normal state.Blinking Data is being transmitted on the Ethernet port. Off The Ethernet connection is not set up.TEL1– TEL2Steady on The terminal is registered with the softswitch but no service ows are transmitted.Blinking Service ows are transmitted.Off The terminal is not powered on or fails to be registered to the softswitch. LOS/PON See Table 2.POWERSteady green The terminal is powered on.Off The power supply is cut off.
The LOS indicator blinks. If the LOS indicator blinks once two seconds, check whether the pigtail fiber is properly connected and the connector is clean. If the GPON terminal blinks twice a second, contact the service provider for help.The PON indicator is off. Check whether the OPTICAL port and optical fiber is properly connected. The GPON terminal fails to register with the upper-layer device. Contact the service provider for help.How to reset the GPON terminal? Press RESET by using a needle-type object.How can I restore factory defaults? Press RESET by using a needle-type object for longer than 10s to restore factory defaults and reset the GPON terminal. If the indicator is off and then is lit, the system restarts successfully.FAQs9Table 2 Indicator status description 2Status No.Status DescriptionPON LOS1Off OffThe GPON terminal is prohibited by the upper-layer device, contact the service provider for help.2Blinks twice a second Off The GPON terminal attempts to set up a connection with its upper-layer device.3 Steady on Off A connection is set up between the GPON terminal and its upper-layer device.4Off Blinks once two secondsThe GPON terminal is not connected to optical bers or does not receive optical signals.5Blinks twice a secondBlinks twice a secondThe GPON terminal is a rogue terminal, contact the service provider for help.6Blinks twice a secondBlinks once two secondsThe Rx optical  power  of the GPON  terminal does  not  within  the  range  (–27  dBm  to  –8 dBm) of the Rx sensitivity.7Blinks once two secondsBlinks once two seconds The hardware is faulty.
Warranty CardUser InformationPersonal or company's full name:__________________________________________________Address/Postal Code:_________________________________________________Telephone:__________________________________________________________Email:______________________________________________________________Product Type:________________________________________________________Product Serial Number:________________________________________________Purchase Date:______________________________________________________Invoice Number:______________________________________________________Dealer's Name:______________________________________________________Dealer's Address:_____________________________________________________Dealer's Telephone:___________________________________________________Thank you for choosing Huawei Technologies Co., Ltd. To get better services, please read this warranty card carefully, ll in the required information, and preserve this card in good condition.Preserve well. No reissue.Dealer's Seal
Limited WarrantySubject to the exclusions contained below, Huawei Technologies Co., Ltd. (Huawei for short) warrants its access terminals ("Products") to be free from defects in materials and workmanship under normal consumer usage for one year from the date of purchase of the product ("Warranty period"). During the warranty period, a Huawei authorized service partner shall remedy defects in materials and workmanship free of charge. Special Notice:1. The warranty card shall be applicable only after being stamped by the dealer.  2. The warranty card must be preserved in good condition and free of any scratch or alteration. 3. To claim such service for defects that are not included in the following exclusion terms, the warranty card and the invoice that records that product serial number shall be presented to a Huawei authorized service partner.Special Notice:1. The warranty card shall be applicable only after being stamped by the dealer.  2. The warranty card must be preserved in good condition and free of any scratch or alteration. 3. To claim such service for defects that are not included in the following exclusion terms, the warranty card and the invoice that records that product serial number shall be presented to a Huawei authorized service partner.Exclusions:In any of the following cases, the warranty card becomes unenforceable or inapplicable without prior notice: 1. The defects are caused by improper handling in transportation and assembly. 2. The defects are caused by the fact that the product is dismantled or altered by anyone that is not from a Huawei authorized service partner. 3. The defects are caused by the fact that the product is used in a harsh environment that is not suitable for the operation of the product. 4. The defects are caused by any force majeure including but not limited to re, earthquake, lightning, and tsunami.  5. The defects are caused by the fact that the product is used or handled incorrectly, roughly or not as instructed in the applicable User Guide. 6. The normal wear and tear, including but not limited to the normal wear and tear of the shell and the power module, shall not be covered by the limited warranty. 7. The warranty card is altered or illegible, or the product serial number recorded on the warranty card is inconsistent with the actual one imprinted or labeled on the product.In any case that is not covered by this limited warranty or should the warranty expire, Huawei shall charge for the service(s) claimed for the products if the product is still remediable. Huawei reserves all rights to interpret this limited warranty. Huawei Technologies Co., Ltd.Address: Huawei Industrial BaseBantian, LonggangShenzhen 518129People's Republic of ChinaWebsite: http://www.huawei.com
Qualication CardPASSCopyright © Huawei Technologies Co., Ltd. 2015 All rights reserved.No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.All other trademarks and trade names mentioned in this document are the property of their respective holders.NoticeThe information in this document is subject to change without notice. Unless otherwise stated, this guide serves only as a guide. All statements, information, and recommendations in this document do not constitute a warranty of any kind, expressed or implied.

Navigation menu