Huawei Technologies RRU3268 Remote Radio Unit User Manual Installation Guide

Huawei Technologies Co.,Ltd Remote Radio Unit Installation Guide

UserManual_RRU3268_installation_guide.pdf

RRU3268Installation GuideIssueDateHUAWEI TECHNOLOGIES CO., LTD.
  Copyright © Huawei Technologies Co., Ltd. 2013. All rights reserved.No part of this document may be reproduced or transmitted in any form or by any means without prior writtenconsent of Huawei Technologies Co., Ltd. Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.All other trademarks and trade names mentioned in this document are the property of their respective holders. NoticeThe purchased products, services and features are stipulated by the contract made between Huawei and thecustomer. All or part of the products, services and features described in this document may not be within thepurchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,and recommendations in this document are provided "AS IS" without warranties, guarantees or representationsof any kind, either express or implied.The information in this document is subject to change without notice. Every effort has been made in thepreparation of this document to ensure accuracy of the contents, but all statements, information, andrecommendations in this document do not constitute a warranty of any kind, express or implied.        Huawei Technologies Co., Ltd.Address: Huawei Industrial BaseBantian, LonggangShenzhen 518129People's Republic of ChinaWebsite: http://www.huawei.comEmail: support@huawei.comIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.i
About This DocumentPurposeThis document describes the process of installing a DC RRU3268 (referred to as RRU in thisdocument).Product VersionsThe following table lists the product versions related to this document.Product Name Product VersionDBS3900 V100R008C00 and later versionsDBS3900 LTE V100R006C00 and later versions Intended AudienceThis document is intended for:Base station installation engineersOrganization1 Changes in the RRU3268 Installation GuideThis chapter describes the changes in the RRU3268 Installation Guide.2 Installation PreparationsThis chapter describes the reference documents, tools, and instruments that must be ready beforethe installation. In addition, it specifies the skills and prerequisites that installation engineersmust have.3 Information About the InstallationBefore installing an RRU, you must be familiar with its exterior, ports, indicators, installationoptions and installation clearance requirements.4 Unpacking the EquipmentRRU3268Installation Guide About This DocumentIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.ii
This chapter describes how to unpack and check the delivered equipment to ensure that all thematerials are included and intact.5 Installation ProcessThe installation process involves installing an RRU and RRU cables, checking the RRUhardware installation, and powering on the RRU.6 (Optional) Installing the Plastic Shells of the RRUThis section describes the procedure for installing the plastic shells of the RRU.7 Hoisting an RRU and Related Cables onto a TowerThis section describes the procedure for hoisting an RRU and related cables onto a tower andthe precautions that must be taken.8 Installing the RRUThis chapter describes the procedure for installing the RRU. The RRU can be installed on a pole,U-steel, angle steel, wall, or an IFS06 . The procedure for installing the RRU varies dependingon installation options.9 Installing RRU CablesThis chapter describes the procedure for installing RRU cables.10 Checking the RRU Hardware InstallationAfter an RRU is installed, check the hardware installation.11 Powering On an RRUAfter all the devices are installed, check the power-on status of an RRU.12 AppendixThis section describes the procedure for adding an easy power receptacle (pressfit type)connector.ConventionsSymbol ConventionsThe symbols that may be found in this document are defined as follows.Symbol DescriptionIndicates a hazard with a high level or medium level of riskwhich, if not avoided, could result in death or serious injury.Indicates a hazard with a low level of risk which, if notavoided, could result in minor or moderate injury.Indicates a potentially hazardous situation that, if notavoided, could result in equipment damage, data loss,performance deterioration, or unanticipated results.RRU3268Installation Guide About This DocumentIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.iii
Symbol DescriptionIndicates a tip that may help you solve a problem or savetime.Provides additional information to emphasize or supplementimportant points of the main text. General ConventionsThe general conventions that may be found in this document are defined as follows.Convention DescriptionTimes New Roman Normal paragraphs are in Times New Roman.Boldface Names of files, directories, folders, and users are inboldface. For example, log in as user root.Italic Book titles are in italics.Courier New Examples of information displayed on the screen are inCourier New. Command ConventionsThe command conventions that may be found in this document are defined as follows.Convention DescriptionBoldface The keywords of a command line are in boldface.Italic Command arguments are in italics.[ ] Items (keywords or arguments) in brackets [ ] are optional.{ x | y | ... } Optional items are grouped in braces and separated byvertical bars. One item is selected.[ x | y | ... ] Optional items are grouped in brackets and separated byvertical bars. One item is selected or no item is selected.{ x | y | ... }*Optional items are grouped in braces and separated byvertical bars. A minimum of one item or a maximum of allitems can be selected.[ x | y | ... ]*Optional items are grouped in brackets and separated byvertical bars. Several items or no item can be selected. GUI ConventionsThe GUI conventions that may be found in this document are defined as follows.RRU3268Installation Guide About This DocumentIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.iv
Convention DescriptionBoldface Buttons, menus, parameters, tabs, window, and dialog titlesare in boldface. For example, click OK.>Multi-level menus are in boldface and separated by the ">"signs. For example, choose File > Create > Folder. Keyboard OperationsThe keyboard operations that may be found in this document are defined as follows.Format DescriptionKey Press the key. For example, press Enter and press Tab.Key 1+Key 2 Press the keys concurrently. For example, pressing Ctrl+Alt+A means the three keys should be pressed concurrently.Key 1, Key 2 Press the keys in turn. For example, pressing Alt, A meansthe two keys should be pressed in turn. Mouse OperationsThe mouse operations that may be found in this document are defined as follows.Action DescriptionClick Select and release the primary mouse button without movingthe pointer.Double-click Press the primary mouse button twice continuously andquickly without moving the pointer.Drag Press and hold the primary mouse button and move thepointer to a certain position.RRU3268Installation Guide About This DocumentIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.v
ContentsAbout This Document.....................................................................................................................ii1 Changes in the RRU3268 Installation Guide...........................................................................12 Installation Preparations..............................................................................................................22.1 Reference Documents.........................................................................................................................................32.2 Tools and Instruments........................................................................................................................................32.3 Skills and Requirements for Onsite Personnel...................................................................................................53 Information About the Installation...........................................................................................63.1 RRU Exterior......................................................................................................................................................73.2 RRU Ports...........................................................................................................................................................83.3 RRU Indicators...................................................................................................................................................93.4 Installation Scenarios........................................................................................................................................113.5 Installation Clearance Requirements of an RRU..............................................................................................213.5.1 Clearance for a Single RRU....................................................................................................................213.5.2 Clearance for Multiple RRUs..................................................................................................................243.5.3 Installation Spacing Between RRUs........................................................................................................284 Unpacking the Equipment.........................................................................................................315 Installation Process.....................................................................................................................336 (Optional) Installing the Plastic Shells of the RRU..............................................................347 Hoisting an RRU and Related Cables onto a Tower............................................................377.1 Hoisting an RRU onto a Tower........................................................................................................................387.2 Hoisting Fiber Optic Cables onto a Tower.......................................................................................................427.3 Hoisting Power Cables onto a Tower...............................................................................................................458 Installing the RRU.......................................................................................................................498.1 Mounting Kits for an RRU...............................................................................................................................508.2 Installing the RRU on a Pole............................................................................................................................518.2.1 Installing a Single RRU...........................................................................................................................518.2.2 Installing Two RRUs...............................................................................................................................548.2.3 Installing Three or More RRUs...............................................................................................................588.3 Installing the RRU on U-steel..........................................................................................................................638.4 Installing the RRU on Angle Steel...................................................................................................................68RRU3268Installation Guide ContentsIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.vi
8.5 Installing the RRU on a Wall...........................................................................................................................738.6 Installing an RRU on an IFS06.........................................................................................................................799 Installing RRU Cables................................................................................................................879.1 Cabling Requirements......................................................................................................................................899.2 Cable Connections............................................................................................................................................949.3 Installation Process...........................................................................................................................................969.4 RRU Cable List................................................................................................................................................979.5 Installing an RRU PGND Cable.......................................................................................................................999.6 Installing an RRU RF Jumper........................................................................................................................1009.7 Installing an RRU AISG Multi-Wire Cable and AISG Extension Cable.......................................................1039.8 Installing an RRU Alarm Cable......................................................................................................................1069.9 Opening the Cover Plate of an RRU Cabling Cavity.....................................................................................1079.10 Installing an RRU Power Cable....................................................................................................................1089.11 Installing a CPRI Fiber Optic Cable.............................................................................................................1109.12 Closing the Cover Plate of an RRU Cabling Cavity....................................................................................11210 Checking the RRU Hardware Installation..........................................................................11611 Powering On an RRU.............................................................................................................11712 Appendix...................................................................................................................................11912.1 Adding a Tool-Less Female Connector (Pressfit Type) to the RRU Power Cable on the RRU Side..........120RRU3268Installation Guide ContentsIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.vii
1 Changes in the RRU3268 Installation GuideThis chapter describes the changes in the RRU3268 Installation Guide.01 (2013-03-18)This is the first official release.RRU3268Installation Guide 1 Changes in the RRU3268 Installation GuideIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.1
2 Installation PreparationsAbout This ChapterThis chapter describes the reference documents, tools, and instruments that must be ready beforethe installation. In addition, it specifies the skills and prerequisites that installation engineersmust have.2.1 Reference DocumentsBefore the installation, you must be familiar with reference documents.2.2 Tools and InstrumentsAll tools and instruments required for RRU installation must be ready before the installation.2.3 Skills and Requirements for Onsite PersonnelOnsite personnel must be qualified and trained. Before performing any operation, onsitepersonnel must be familiar with correct operation methods and safety precautions.RRU3268Installation Guide 2 Installation PreparationsIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.2
2.1 Reference DocumentsBefore the installation, you must be familiar with reference documents.The following reference documents are required during RRU installation:lRRU3268 Hardware DescriptionlDBS3900 Installation GuidelOCB User Guide2.2 Tools and InstrumentsAll tools and instruments required for RRU installation must be ready before the installation.Hammer drill (a φ 12 bit) ESD gloves Vacuum cleanerHeat gun Phillips screwdriver (M3 toM6)Flat-head screwdriver (M3 toM6)Rubber mallet COAX crimping tool Wire stripperRRU3268Installation Guide 2 Installation PreparationsIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.3
Utility knife Cable cutter Adjustable wrench (capacity≥ 32 mm [1.26 in.])Torque wrenchCapacity: 16 mm [0.63 in.],and 32 mm [1.26 in.]Combination wrenchCapacity: 16 mm [0.63 in.],and 32 mm [1.26 in.]Level Torque screwdriver5 mm (0.2 in.)5 mm (0.2 in.)(M3 to M6)(M3 to M6)Torque socketMultimeter Marker (diameter ≤ 10 mm[0.39 in.])Measuring tapeInner hexagon spanner5 mm (0.2 in.)Fixed pulley RopeHydraulic pliers - - RRU3268Installation Guide 2 Installation PreparationsIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.4
2.3 Skills and Requirements for Onsite PersonnelOnsite personnel must be qualified and trained. Before performing any operation, onsitepersonnel must be familiar with correct operation methods and safety precautions.Before the installation, pay attention to the following items:lThe customer's technical engineers must be trained by Huawei and be familiar with theproper installation and operation methods.lThe number of onsite personnel depends on the engineering schedule and installationenvironment. Generally, only three to five onsite personnel are necessary.RRU3268Installation Guide 2 Installation PreparationsIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.5
3 Information About the InstallationAbout This ChapterBefore installing an RRU, you must be familiar with its exterior, ports, indicators, installationoptions and installation clearance requirements.3.1 RRU ExteriorThis section describes the exterior and dimensions of an RRU.3.2 RRU PortsThis section describes ports on the RRU panels. An RRU has a bottom panel, cabling cavitypanel, and indicator panel.3.3 RRU IndicatorsThis section describes six indicators on an RRU. They indicate the running status.3.4 Installation ScenariosAn RRU can be installed on a pole, U-steel, angle steel, or IFS06. Installation scenarios mustmeet heat-dissipation and waterproofing requirements of the RRU.3.5 Installation Clearance Requirements of an RRUThis section describes the requirements for the installation clearance of a single RRU andmultiple RRUs and the requirements for the installation spacing between RRUs.RRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.6
3.1 RRU ExteriorThis section describes the exterior and dimensions of an RRU.Figure 3-1 shows an RRU.Figure 3-1 RRU exterior Figure 3-2 shows RRU dimensions.Figure 3-2 RRU dimensions RRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.7
3.2 RRU PortsThis section describes ports on the RRU panels. An RRU has a bottom panel, cabling cavitypanel, and indicator panel.Figure 3-3 shows the ports on the RRU panels.Figure 3-3 Ports on the RRU panels Table 3-1 describes ports and indicators on the RRU panels.Table 3-1 RRU ports and indicators on the panelsItem Silkscreen Description(1) Ports in the cablingcavityRTN(+) Power portNEG(-)CPRI0 Optical/electrical port 0RRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.8
Item Silkscreen DescriptionCPRI1 Optical/electrical port 1(2) Ports at the bottom ANT_TX/RXA TX/RX port A, supporting RET signaltransmissionANT_TX/RXB TX/RX port BEXT_ALM Alarm portRET Communication port for the RET antenna,supporting RET signal transmission(3) Indicators RUN For details, see 3.3 RRU Indicators.ALMACTVSWRCPRI0CPRI1 3.3 RRU IndicatorsThis section describes six indicators on an RRU. They indicate the running status.For detailed positions of RRU indicators, see 3.2 RRU Ports.Table 3-2 describes RRU indicators.Table 3-2 RRU indicatorsIndicator Color Status MeaningRUN Green Steady on There is power supply, but the module isfaulty.Steady off There is no power supply, or the module isfaulty.Blinking (on for1s and off for 1s)The board is functioning properly.Blinking (on for0.125s and off for0.125s)Software is being loaded to the module, orthe module is not started.ALM Red Steady on Alarms are generated, and the module mustbe replaced.RRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.9
Indicator Color Status MeaningBlinking (on for1s and off for 1s)Alarms are generated. The alarms may becaused by the faults on the related boards orports. Therefore, you need to locate the faultbefore deciding whether to replace themodule.Steady off No alarm is generated.ACT Green Steady on The module is running properly with TXchannels enabled or the software is beingloaded without RRU running.Blinking (on for1s and off for 1s)The module is running properly with TXchannels disabled.VSWR Red Steady off No Voltage Standing Wave Ratio (VSWR)alarm is generated.Blinking (on for1s and off for 1s)VSWR alarms are generated on theANT_TX/RXB port.Steady on VSWR alarms are generated on theANT_TX/RXA port.Blinking (on for0.125s and off for0.125s)VSWR alarms are generated on theANT_TX/RXA and ANT_TX/RXB ports.CPRI0 Red orgreenSteady green The CPRI link is functioning properly.Steady red An optical module fails to transmit or receivesignals because the optical module is faultyor the fiber optic cable is broken.Blinking red (onfor 1s and off for1s)The CPRI link is out of lock because of afailure in clock lock between two modes ormismatched data rates over CPRI ports.Steady off The optical module cannot be detected, or theoptical module is powered off.CPRI1 Red orgreenSteady green The CPRI link is functioning properly.Steady red An optical module fails to transmit or receivesignals because the optical module is faultyor the fiber optic cable is broken.Blinking red (onfor 1s and off for1s)The CPRI link is out of lock because of afailure in clock lock between two modes ormismatched data rates over CPRI ports.Steady off The optical module cannot be detected, or theoptical module is powered off. RRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.10
3.4 Installation ScenariosAn RRU can be installed on a pole, U-steel, angle steel, or IFS06. Installation scenarios mustmeet heat-dissipation and waterproofing requirements of the RRU.Requirements for the Installation ScenariosApplication scenarios:To ensure proper heat dissipation of the RRU, the following requirements must be met:lThe RRU cannot be installed in an enclosed cabinet without a cooling system.lThe RRU cannot be installed in an enclosed camouflage box.lThe RRU cannot be installed in an enclosed equipment room without a cooling system.lWhen multiple RRUs are installed in centralized mode, the minimum clearancerequirements must be met. For details about the minimum clearance requirements, see 3.5.2Clearance for Multiple RRUs and 3.5.3 Installation Spacing Between RRUs.CAUTIONIn improper installation scenarios, the heat dissipation efficiency decreases and therefore theRRU may not work properly. Figure 3-4 shows an improper installation scenario.Figure 3-4 Improper installation scenario Method of installation:lTo ensure proper heat dissipation and waterproofing of the RRU, the RRU must be installedwith the ports at the bottom and the vertical deviation angle of the RRU must be less thanor equal to 10 degrees, as shown in Figure 3-5.lThe side-mounted mode is recommended for RRUs on the main pole secured on a tower.This installation mode allows multiple RRUs to be installed next to each other at the sameRRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.11
level on a pole. When the horizontal distance between the main and auxiliary poles on atower is equal to or greater than 810 mm (23.62 in.), the side-mounted mode isrecommended for installing RRUs on the auxiliary pole to meet the minimum clearancerequirements. Otherwise, the standard mode is recommended for installing RRUs on theauxiliary pole.Figure 3-5 Requirements for the vertical deviation angle of an RRU(1) RRU (2) Installation support (pole, U-steel, angle steel, or wall) Installing an RRU on a PoleFigure 3-6 shows the diameter of a pole for installing an RRU.Figure 3-6 Diameter of a pole CAUTIONlThe diameter of a pole for installing an RRU ranges from 60 mm (2.36 in.) to 114 mm (4.49in.). The recommended diameter is 80 mm (3.15 in.).RRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.12
Figure 3-7 shows a single RRU installed on a pole.Figure 3-7 A single RRU installed on a pole Figure 3-8 shows two RRUs installed on a pole.Figure 3-8 Two RRUs installed on a pole Figure 3-9, Figure 3-10, and Figure 3-11 show three or more RRUs installed on a pole.RRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.13
Figure 3-9 Three RRUs installed on a pole Figure 3-10 Four RRUs installed on a pole RRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.14
Figure 3-11 Six RRUs installed on a pole Installing an RRU on U-steelFigure 3-12 shows U-steel specifications.Figure 3-12 U-steel specifications CAUTIONU-steel supports the standard or reverse installation of a single RRU only.Figure 3-13 shows an RRU installed on U-steel.RRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.15
Figure 3-13 RRU installed on U-steel Installing an RRU on Angle SteelFigure 3-14 shows angle steel specifications.Figure 3-14 Angle steel specifications CAUTIONAngle steel supports the standard or reverse installation of a single RRU only.Figure 3-15 shows an RRU installed on angle steel.RRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.16
Figure 3-15 RRU installed on angle steel Installing an RRU on a WallThe wall for installing RRUs must meet the following requirements:lWhen a single RRU is installed, the wall has a capacity of bearing at least four times theweight of the RRU.lExpansion anchor bolts must be tightened to 30 N·m (265.52 lbf·in.) so that the bolts staysecured without damaging the wall.CAUTIONlIt is recommended that the RRU be installed on a wall in standard mode.lWhen multiple RRUs are installed on an outdoor wall in side-mounted mode, it isrecommended that the mounting brackets not be combined, as shown in Figure 3-16. Whenmultiple RRUs are installed on an indoor wall in side-mounted mode, the mounting bracketscannot be combined, as shown in Figure 3-17.Figure 3-16 Correct installation of mounting brackets for multiple RRUs installed on an outdoorwall in side-mounted modeRRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.17
 Figure 3-17 Correct installation of mounting brackets for multiple RRUs installed on an indoorwall in side-mounted mode Figure 3-18 shows an RRU installed on a wall.Figure 3-18 RRU installed on a wall Installing an RRU on an IFS06In an IFS06 scenario:lThe upper and lower adjustable beams on an IFS06 can be moved up and down to fit forheights of RRUs.lThe IFS06 supports at least three RRUs when the ambient temperature is higher than orequal to the lowest operating temperature of the RRU and at least 5°C (41°F) lower thanthe highest operating temperature of the RRU. The IFS06 supports a maximum of six RRUswhen the ambient temperature is higher than or equal to the lowest operating temperatureRRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.18
of the RRU and at least 10°C (50°F) lower than the highest operating temperature of theRRU.NOTEFor details about the operating temperature of the RRU, see section "Technical Specifications ofRRUs" in 3900 Series Base Station Technical Description.CAUTIONThe mounting brackets for multiple RRUs cannot be combined when the RRUs are installed onan IFS06, as shown in Figure 3-19.Figure 3-19 Correct installation of mounting brackets for RRUs installed on an IFS06 Figure 3-20 and Figure 3-21 show RRUs installed on an IFS06.RRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.19
Figure 3-20 Three RRUs installed on an IFS06(1) Height-restricted scenario (2) Height-unrestricted scenario RRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.20
Figure 3-21 Six RRUs installed on an IFS06 (1) Height-restricted scenario (2) Height-unrestricted scenario3.5 Installation Clearance Requirements of an RRUThis section describes the requirements for the installation clearance of a single RRU andmultiple RRUs and the requirements for the installation spacing between RRUs.3.5.1 Clearance for a Single RRUThis section describes the recommended and minimum clearance for a single RRU.RRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.21
NOTElThe recommended clearance ensures normal running and provides an appropriate space for operationand maintenance (OM). If there is sufficient space, leave the recommended clearance after installingthe equipment.lThe minimum clearance ensures normal running and heat dissipation, but OM activities such aschecking indicator status and opening the cabling cavity cannot be properly conducted. If theinstallation space is restricted, leave the minimum clearance after installing the equipment.Clearances for a Single RRU in Standard or Reverse ModeFigure 3-22 shows the clearances for a single RRU in standard or reverse mode.Figure 3-22 Clearances for a single RRU in standard or reverse mode RRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.22
Clearances for a Single RRU in Side-Mounted ModeFigure 3-23 shows the clearances for a single RRU in side-mounted mode.Figure 3-23 Clearances for a single RRU in side-mounted mode Clearances for a Single Tower-mounted RRUFigure 3-24 and Figure 3-25 show the clearances for a single tower-mounted RRU in standardor reverse mode and in side-mounted mode, respectively.RRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.23
Figure 3-24 Minimum clearance for a single tower-mounted RRU in standard or reverse mode Figure 3-25 Minimum clearance for a single tower-mounted RRU in side-mounted mode 3.5.2 Clearance for Multiple RRUsThis section describes the recommended and minimum clearance for multiple RRUs.RRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.24
NOTElThe recommended clearance ensures normal running and provides an appropriate space for operationand maintenance (OM). If there is sufficient space, leave the recommended clearance after installingthe equipment.lThe minimum clearance ensures normal running and heat dissipation, but OM activities such aschecking indicator status and opening the cabling cavity cannot be properly conducted. If theinstallation space is restricted, leave the minimum clearance after installing the equipment.Recommended Clearance for Multiple RRUs Installed in Centralized ModeFigure 3-26 shows the recommended clearance for multiple RRUs installed in centralized mode.Figure 3-26 Recommended clearances for three or more RRUs installed on a pole Minimum Clearance for Multiple RRUs Installed in Centralized ModeFigure 3-27 shows the minimum clearance for multiple RRUs installed in centralized mode.RRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.25
Figure 3-27 Minimum clearances for multiple RRUs installed in centralized mode Recommended Clearance for Multiple RRUs Installed on a Wall in Standard ModeFigure 3-28 shows the recommended clearance for multiple RRUs installed on a wall in standardmode.Figure 3-28 Recommended clearances for three or more RRUs installed on a wall in standardmodeRRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.26
 Minimum Clearance for Multiple RRUs Installed on a Wall in Standard ModeFigure 3-29 shows the minimum clearance for multiple RRUs installed on a wall in standardmode.Figure 3-29 Minimum clearances for three or more RRUs installed on a wall in standard mode Recommended Clearance for Multiple RRUs Side-Mounted on a WallFigure 3-30 shows the recommended clearance for multiple RRUs side-mounted on a wall.RRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.27
Figure 3-30 Recommended clearances for three or more RRUs installed on a wall in side-mounted mode 3.5.3 Installation Spacing Between RRUsThis section describes the horizontal and vertical spacing between RRUs.Recommended Horizontal Spacing Between RRUsFigure 3-31 shows the recommended horizontal spacing between RRUs.Figure 3-31 Recommended horizontal spacing between RRUs Minimum Horizontal Spacing Between RRUsFigure 3-32 shows the minimum horizontal spacing between RRUs.RRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.28
Figure 3-32 Minimum horizontal spacing between RRUs Recommended Vertical Spacing Between RRUsFigure 3-33 shows the recommended vertical spacing between RRUs.Figure 3-33 Recommended vertical spacing between RRUs Minimum Vertical Spacing Between RRUsFigure 3-34 shows the minimum vertical spacing between RRUs.RRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.29
Figure 3-34 Minimum vertical spacing between RRUsRRU3268Installation Guide 3 Information About the InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.30
4 Unpacking the EquipmentThis chapter describes how to unpack and check the delivered equipment to ensure that all thematerials are included and intact.ContextNOTEWhen transporting, moving, or installing the equipment, components, or parts, you must:lEnsure that they are transported in the delivered packages instead of being unpacked or in non-standard packages. If boards are used for a trial and then transported to sites, pack the boards againbefore transportation.lPrevent them from colliding with doors, walls, shelves, or other objects.lWear clean gloves, and avoid touching the equipment, components, or parts with bare hands, sweat-soaked gloves, or dirty gloves.CAUTIONlAfter a cabinet or an BBU is unpacked, it must be powered on within 7 days.lAfter an RRU is unpacked, it must be powered on within 24 hours.ProcedureStep 1 Check the total number of articles in each case according to the packing list.If ... Then ...The total number tallies with the packinglistGo to Step 2.The total number does not tally with thepacking listFind out the cause and report any missingarticles to the local Huawei office.Step 2 Check the exterior of the packing case.RRU3268Installation Guide 4 Unpacking the EquipmentIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.31
If ... Then ...The outer packing is intact Go to Step 3.The outer packing is severely damaged orsoakedFind out the cause and report it to the localHuawei office.The shockwatch label is red Stop unpacking the wooden crate, and thenreport it to the transportation company.Step 3 Check the type and quantity of the equipment in the cases according to the packing list.If ... Then ...Types and quantity of the article tally withthose on the packing listSign the Packing List with the customer.Either shipment shortage, wrong shipmentor damaged articles.Report to the local Huawei office.WARNINGTo protect the equipment and prevent damage to the equipment, you are advised to keep theunpacked equipment and packing materials indoors, take photos of the stocking environment,packing case or carton, packing materials, and any rusted or eroded equipment, and then file thephotos.----EndRRU3268Installation Guide 4 Unpacking the EquipmentIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.32
5 Installation ProcessThe installation process involves installing an RRU and RRU cables, checking the RRUhardware installation, and powering on the RRU.Figure 5-1 shows the process of installing an RRU.Figure 5-1 Process of installing an RRURRU3268Installation Guide 5 Installation ProcessIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.33
6 (Optional) Installing the Plastic Shells of theRRUThis section describes the procedure for installing the plastic shells of the RRU.ContextAn RRU is equipped with a plastic shell only when necessary.ProcedureStep 1 Use an M6 Phillips screwdriver to loosen the two screws on the metal sheet of the RRU andremove the metal sheet, as shown in Figure 6-1.Figure 6-1 Removing the metal sheet RRU3268Installation Guide 6 (Optional) Installing the Plastic Shells of the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.34
(1) Screw (2) Metal sheetStep 2 Install a buckle on each side at the bottom of the RRU, and use an M4 torque wrench to tightenthe screws on the buckles to 1.4 N•m (12.39 lbf•in.), as shown in Figure 6-2.Figure 6-2 Installing buckles at the bottom (1) Buckle (2) ScrewStep 3 Use four hex screws to secure the plastic shells onto the RRU and use an M6 hex key wrenchto tighten the screws to 2.8 N•m (24.78 lbf•in.), as shown in Figure 6-3.RRU3268Installation Guide 6 (Optional) Installing the Plastic Shells of the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.35
Figure 6-3 Installing the plastic shells of the RRU----EndRRU3268Installation Guide 6 (Optional) Installing the Plastic Shells of the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.36
7 Hoisting an RRU and Related Cables onto aTowerAbout This ChapterThis section describes the procedure for hoisting an RRU and related cables onto a tower andthe precautions that must be taken.7.1 Hoisting an RRU onto a TowerThis section describes the procedures and precautions for hoisting an RRU and its mounting kitsonto a tower. In tower-mounted scenario, the RRU can be installed on a pole, U-steel, or anglesteel.7.2 Hoisting Fiber Optic Cables onto a TowerThis section describes the procedure for hoisting fiber optic cables onto a tower and theprecautions that must be taken.7.3 Hoisting Power Cables onto a TowerThis section describes the procedure for hoisting power cables onto a tower and the precautionsthat must be taken.RRU3268Installation Guide 7 Hoisting an RRU and Related Cables onto a TowerIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.37
7.1 Hoisting an RRU onto a TowerThis section describes the procedures and precautions for hoisting an RRU and its mounting kitsonto a tower. In tower-mounted scenario, the RRU can be installed on a pole, U-steel, or anglesteel.PrerequisitesWhen the RRU is used with an AC/DC power module, you need to install the AC/DC powermodule onto the RRU before hoisting the RRU onto a tower. For details about how to install anAC/DC power module onto the RRU, see Installing an AC/DC Power Module onto an RRU.CAUTIONlDo not stand the RRU upright because the RF ports cannot support the weight of the RRU.lPlace a foam pad or cardboard under the RRU to protect the RRU housing from damageduring the installation.ProcedureStep 1 Hoist the RRU and mounting kits onto the tower respectively, as shown in Figure 7-1.NOTEHoist mounting kits onto the tower and then install the mounting kits before hoisting the RRU onto thetower. When hoisting the mounting kits and RRU, protect them from colliding with the tower.RRU3268Installation Guide 7 Hoisting an RRU and Related Cables onto a TowerIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.38
Figure 7-1 Hoisting the RRU onto the tower(1) Lifting sling (2) Fixed pulley (3) Traction sling 1. After climbing up to the tower, installation engineer A secures the fixed pulley to the towerplatform support and leads the lifting sling through the fixed pulley.2. Installation engineer C binds the RRU mounting kits properly using a lifting sling, as shownin Figure 7-2, and binds the RRU using a lifting sling and a traction sling, as shown inFigure 7-3.RRU3268Installation Guide 7 Hoisting an RRU and Related Cables onto a TowerIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.39
Figure 7-2 Binding mounting kits for the RRUFigure 7-3 Binding the RRU(1) Handle (2) Lifting sling (3) Traction eye (4) Traction sling RRU3268Installation Guide 7 Hoisting an RRU and Related Cables onto a TowerIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.40
CAUTIONlThe load-bearing capacity of each sling must be greater than 200 kg (441 lb) and thediameter of each sling must be less than 25 mm (0.98 in.).lWhen hoisting the RRU onto a tower, protect them from colliding with the tower andground.lHoist the RRU onto the tower before it is installed on a pole, angle steel, or U-steel.lDo not hoist any thing by the traction eye.lDo not hoist the RRU by the handle or traction eye only, as shown in Figure 7-4 andFigure 7-5.Figure 7-4 Incorrect binding method RRU3268Installation Guide 7 Hoisting an RRU and Related Cables onto a TowerIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.41
Figure 7-5 Incorrect binding method 3. Installation engineer B pulls the lifting sling downwards, and installation engineer C pullsthe traction sling outwards to protect the RRU from colliding with the tower.Step 2 Installation engineer A catches the RRU, install the RRU on the main bracket, use an innerhexagon screwdriver to tighten the captive screw into the hole of the attachment plate to 5 N·m(44.25 lbf·in.) for connecting the attachment plate and the main bracket, see 8 Installing theRRU.Step 3 Remove the lifting sling and traction sling.NOTEThe procedure for hoisting the RRU and mounting kits onto the tower is for your reference only.----End7.2 Hoisting Fiber Optic Cables onto a TowerThis section describes the procedure for hoisting fiber optic cables onto a tower and theprecautions that must be taken.ContextCabling requirements for power cables are met. For details, see 9.1 Cabling Requirements.ProcedureStep 1 Hoist the fiber optic cables onto the tower, as shown in Figure 7-6.RRU3268Installation Guide 7 Hoisting an RRU and Related Cables onto a TowerIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.42
Figure 7-6 Hoisting fiber optic cables onto the tower(1) Lifting sling (2) Fixed pulley (3) Traction slingCAUTIONBefore hoisting fiber optic cables onto the tower, connect the fiber optic cables to the RRU orBBU based on the labels on both ends of the cables and determine the hoisting direction.1. After climbing up to the tower, installation engineer A secures the fixed pulley to the towerplatform support and leads the lifting sling through the fixed pulley.2. Installation engineer B places the fiber coiler for coiling fiber optic cables on the fiberspools, and installation engineer D lead the lifting sling through the stretch sling of the fiberoptic cables and use the other sling as a traction sling to secure the cables 4 m (13.12 ft)away from the lifting sling, as shown in Figure 7-7.RRU3268Installation Guide 7 Hoisting an RRU and Related Cables onto a TowerIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.43
Figure 7-7 Binding fiber optic cables(1) Lifting sling (2) Stretch sling (3) Traction sling CAUTIONDo not remove the stretch sling and protection pipe or bind fiber optic cables using onesling, as shown in Figure 7-8.Figure 7-8 Incorrect binding method 3. Installation engineer B rotates the fiber spools at the speed of 5 m (16.4 ft) to 15 m (49.21ft) per minute to coil the fiber optic cables.RRU3268Installation Guide 7 Hoisting an RRU and Related Cables onto a TowerIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.44
4. Installation engineer C pulls the lifting sling downwards, and installation engineer D pullsthe traction sling outwards to protect the fiber optic cables from colliding with the tower.Step 2 Secure the fiber optic cables to the tower vertically using cable clips.Step 3 Remove the lifting sling, traction sling, and protection pipe.NOTEThe procedure for hoisting the fiber optic cables onto the tower is for your reference only.----End7.3 Hoisting Power Cables onto a TowerThis section describes the procedure for hoisting power cables onto a tower and the precautionsthat must be taken.ContextCabling requirements for power cables are met. For details, see 9.1 Cabling Requirements.The procedure for adding a connector to the RRU power cable on the RRU side is done underthe tower.ProcedureStep 1 Hoist the power cables onto the tower, as shown in Figure 7-9.RRU3268Installation Guide 7 Hoisting an RRU and Related Cables onto a TowerIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.45
Figure 7-9 Hoisting power cables onto the tower(1) Lifting sling (2) Fixed pulley 1. After climbing up to the tower, installation engineer A secures the fixed pulley to the towerplatform support and leads the lifting sling through the fixed pulley.2. Installation engineer B secures three cable ties to the power cable connector, and thensecures the power cable to the lifting sling, as shown in Figure 7-10.NOTEThe connector on the power cable in the figure is only an example. The actual connector may varyaccording to the situation.RRU3268Installation Guide 7 Hoisting an RRU and Related Cables onto a TowerIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.46
Figure 7-10 Binding cable ties 3. Installation engineer B wraps the power cable connector with a layer of PVC insulationtape, as shown in Figure 7-11.NOTEWrap the PVC insulation tape from 30 mm (1.18 in.) away from one end of the connector until itreaches the other end of the connector. The total length of the wrapped connector is 100 mm (3.94in.).RRU3268Installation Guide 7 Hoisting an RRU and Related Cables onto a TowerIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.47
Figure 7-11 Wrapping the PVC insulation tape 4. Installation engineer C pulls the lifting sling downwards, and installation engineer B pullsthe other end of the lifting sling outwards to protect the power cables from colliding withthe tower.Step 2 Secure the power cables to the tower vertically using cable clips.Step 3 Remove the cable ties, PVC insulation tape, and lifting sling.NOTEThe procedure for hoisting the power cables onto the tower is for your reference only.----EndRRU3268Installation Guide 7 Hoisting an RRU and Related Cables onto a TowerIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.48
8 Installing the RRUAbout This ChapterThis chapter describes the procedure for installing the RRU. The RRU can be installed on a pole,U-steel, angle steel, wall, or an IFS06 . The procedure for installing the RRU varies dependingon installation options.8.1 Mounting Kits for an RRUThis section describes the bracket assembly and the attachment plate for an RRU.8.2 Installing the RRU on a PoleOne or more RRUs can be installed on a pole.8.3 Installing the RRU on U-steelThis section describes the procedure and precautions for installing the RRU on U-steel. An RRUcan be installed on U-steel secured on the ground or a tower. Each piece of U-steel allows onlyone RRU to be installed in standard or reverse mode.8.4 Installing the RRU on Angle SteelThis section describes the procedure and precautions for installing the RRU on angle steel. AnRRU can be installed on angle steel secured on the ground or a tower. Each piece of angle steelallows only one RRU to be installed in standard or reverse mode.8.5 Installing the RRU on a WallThis section describes the procedure and precautions for installing the RRU on a wall.8.6 Installing an RRU on an IFS06This section describes the procedure and precautions for installing an RRU on an IFS06.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.49
8.1 Mounting Kits for an RRUThis section describes the bracket assembly and the attachment plate for an RRU.Figure 8-1 shows the front and rear of an RRU.Figure 8-1 Front and side view of an RRU(1) Attachment plate Figure 8-2 shows the bracket assembly for an RRU.Figure 8-2 12 L blade RRU mounting kit(1) Main bracket (2) Pole installationbracket(3) Auxiliary bracket (4) Nut (5) Square-neckbolt(6) Hoist clamp onthe main bracketRRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.50
 8.2 Installing the RRU on a PoleOne or more RRUs can be installed on a pole.8.2.1 Installing a Single RRUThis section describes the procedure and precautions for installing a single RRU on a pole.PrerequisitesBefore you install an RRU on a pole secured on a tower, the RRU and its mounting brackets arehoisted onto the tower. For details, see 7.1 Hoisting an RRU onto a Tower.The hoist clamp on the main bracket is secured properly.CAUTIONlDo not stand the RRU upright because the RF ports cannot support the weight of the RRU.lPlace a foam pad or cardboard under the RRU to protect the RRU housing from damageduring the installation.ProcedureStep 1 Determine a position for installing the mounting brackets.lIf the pole must be installed on a tower, determine a position for installing the mountingbrackets according to the instructions in 3.5.1 Clearance for a Single RRU.lIf the pole must be installed on the ground, determine a position for installing the mountingbrackets according to Figure 8-3.Figure 8-3 Distance between the mounting brackets and the groundRRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.51
 NOTEIt is recommended that the mounting brackets be installed at a height of 1200 mm (47.24 in.) to 1600mm (62.99 in.) above the ground.Step 2 Install the RRU mounting brackets, as shown in Figure 8-4.Figure 8-4 Installing the RRU mounting brackets NOTEVerify that the arrows on the mounting brackets are pointing up.1. Adjust the position of the nut and remove one end of the square-neck bolt from the slot onthe auxiliary bracket.2. Slide the mounting brackets onto the pole horizontally and insert the square-neck bolt intothe slot.Step 3 Use a 16 mm (0.63 in.) M10 torque wrench to tighten the nuts to 40 N·m (354.03 lbf·in.) so thatthe mounting brackets are secured onto the pole, as shown in Figure 8-5.CAUTIONTighten the nuts on the two square-neck bolts alternatively. After the main and auxiliary bracketsare secured properly, measure the spacing between the brackets on both sides and ensure thatthe spacing is the same on the two sides.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.52
Figure 8-5 Securing the RRU mounting brackets Step 4 Install the RRU onto the main bracket, as shown in Figure 8-6.Figure 8-6 Installing the RRU onto the main bracket Step 5 Use an inner hexagon torque screwdriver to tighten the captive screw into the holes on the topof the attachment plate and main bracket to 5 N·m (44.25 lbf·in.) so that the attachment plateand main bracket are firmly secured, as shown in Figure 8-7.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.53
Figure 8-7 Securing the captive screw into the connection hole ----End8.2.2 Installing Two RRUsThis section describes the procedure and precautions for installing two RRUs on a pole.PrerequisitesThe hoist clamp on the main bracket is secured properly.CAUTIONlDo not stand the RRU upright because the RF ports cannot support the weight of the RRU.lPlace a foam pad or cardboard under the RRU to protect the RRU housing from damageduring the installation.ProcedureStep 1 Install the first RRU onto the main bracket, as shown in Figure 8-8. For details, see 8.2.1Installing a Single RRU.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.54
Figure 8-8 Installing the first RRU onto the main bracket Step 2 Use an M6 inner hexagon screwdriver to remove the four inner hexagon screws from the secondset of mounting brackets, and remove the main bracket from the auxiliary bracket, as shown inFigure 8-9.Figure 8-9 Removing the RRU main bracket(1) Main bracket (2) Pole installation bracket Step 3 Install the removed main bracket on one side of the first main bracket, as shown in Figure8-10.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.55
CAUTIONThe second main bracket must be installed with the opening ends of U-shaped slots on both sidesfacing downwards.Figure 8-10 Installing the second main bracket(1) Removed main bracket Step 4 Install the second RRU onto the main bracket, as shown in Figure 8-11.Figure 8-11 Installing the second RRU onto the main bracketRRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.56
 CAUTIONAfter installing each RRU on its main bracket, use an inner hexagon torque screwdriver to tightenthe captive screw into the holes of the attachment plate and main bracket to 5 N·m (44.25 lbf·in.)so that the attachment plate and main bracket are firmly secured, as shown in Figure 8-12.Figure 8-12 Securing the captive screw into the connection hole Step 5 Install the metal sheet for neighboring RRUs, as shown in Figure 8-13.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.57
Figure 8-13 Installing the metal sheet(1) Screw (2) Metal sheet 1. Use an M6 Phillips screwdriver to loosen the screw on the metal sheet farther from thehandle of the first RRU and remove the screw.2. Use an M6 Phillips screwdriver to loosen the screw on the metal sheet closer to handle ofthe first RRU. Then rotate the metal sheet to align the vacant hole in the metal sheet witha hole on the top of the second RRU.3. Insert the removed screw into the hole on the top of the second RRU and use an M6 torquescrewdriver to tighten the screw to 5 N·m (44.25 lbf·in.).----End8.2.3 Installing Three or More RRUsThe section describes the procedure and precautions for installing three or more RRUs on a pole.PrerequisitesThe hoist clamp on the main bracket is secured properly.CAUTIONlDo not stand the RRU upright because the RF ports cannot support the weight of the RRU.lPlace a foam pad or cardboard under the RRU to protect the RRU housing from damageduring the installation.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.58
ContextA pole supports the installation of three, four, or six RRUs. The procedures for installing themare the same. Following is the procedure of installing four RRUs on a pole.ProcedureStep 1 Install the two RRUs, as shown in Figure 8-14. For details, see 8.2.2 Installing Two RRUs.Figure 8-14 Two RRUs installed on a pole Step 2 Use an M6 inner hexagon screwdriver to remove the four inner hexagon screws from the secondset of mounting brackets, and remove the main bracket from the auxiliary bracket, as shown inFigure 8-15.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.59
Figure 8-15 Removing the RRU main bracket(1) Main bracket (2) Pole installation bracket Step 3 Install the third main bracket and install the third RRU onto the third main bracket. Then use aninner hexagon torque screwdriver to tighten the captive screw into the connection holes on thetop of the attachment plate and main bracket for the RRU, with a torque of 5 N·m (44.25 lbf·in.),as shown in Figure 8-16.CAUTIONThe third main bracket must be installed with the opening ends of U-shaped slots on both sidesfacing downwards.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.60
Figure 8-16 Installing the third RRU onto the third main bracket Step 4 Install the metal sheet for neighboring RRUs, as shown in Figure 8-17.Figure 8-17 Installing the metal sheet(1) Screw (2) Metal sheet 1. Use an M6 Phillips screwdriver to loosen the screw on the metal sheet farther from thehandle of the first RRU and remove the screw.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.61
2. Use an M6 Phillips screwdriver to loosen the screw on the metal sheet closer to handle ofthe first RRU. Then rotate the metal sheet to align the vacant hole in the metal sheet witha hole on the top of the second RRU.3. Insert the removed screw into the hole on the top of the second RRU and use an M6 torquescrewdriver to tighten the screw to 5 N·m (44.25 lbf·in.).Step 5 At a position 80 mm (3.15 in.) above or below the first set of RRU mounting brackets, installthe second set of RRU mounting brackets, as shown in Figure 8-18.Figure 8-18 Installing the second set of RRU mounting brackets Step 6 Install the fourth RRU onto the fourth main bracket, use an inner hexagon torque screwdriverto tighten the captive screw into the holes of the attachment plate and main bracket to 5 N·m(44.25 lbf·in.) so that the attachment plate and main bracket are firmly secured, as shown inFigure 8-19.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.62
Figure 8-19 Installing the fourth RRU onto the fourth main bracket ----End8.3 Installing the RRU on U-steelThis section describes the procedure and precautions for installing the RRU on U-steel. An RRUcan be installed on U-steel secured on the ground or a tower. Each piece of U-steel allows onlyone RRU to be installed in standard or reverse mode.PrerequisitesBefore you install an RRU on U-steel secured on a tower, the RRU and its mounting bracketsare hoisted onto the tower. For details, see 7.1 Hoisting an RRU onto a Tower.The hoist clamp on the main bracket is secured properly.CAUTIONlDo not stand the RRU upright because the RF ports cannot support the weight of the RRU.lPlace a foam pad or cardboard under the RRU to protect the RRU housing from damageduring the installation.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.63
ContextFigure 8-20 shows the top view of the RRU installed on U-steel.CAUTIONWhen the width of the narrower edges of the U-steel is less than 40 mm (1.57 in.), only the aand b modes are supported.Figure 8-20 Top view of the RRU(1) U-steel ProcedureStep 1 Determine a position for installing the mounting brackets.lIf the RRU must be installed on U-steel secured on a tower, see 3.5.1 Clearance for aSingle RRU to determine a position.lIf the RRU must be installed on U-steel secured on the ground, see Figure 8-21 to determinea position.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.64
Figure 8-21 Distance between the mounting brackets and the ground NOTEIt is recommended that the mounting brackets be installed at a height of 1200 mm (47.24 in.) to 1600mm (62.99 in.) above the ground.Step 2 Install the RRU mounting brackets, as shown in Figure 8-22.Figure 8-22 Installing the RRU mounting brackets NOTEVerify that the arrows on the mounting brackets are pointing up.1. Adjust the position of the nut and remove one end of the square-neck bolt from the slot onthe auxiliary bracket.2. Slide the mounting brackets onto the U-steel horizontally and insert the square-neck boltinto the slot.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.65
Step 3 Use a 16 mm (0.67 in.) M10 torque wrench to tighten the nuts to 40 N·m (354.03 lbf·in.) so thatthe mounting brackets are secured onto the U-steel, as shown in Figure 8-23.CAUTIONTighten the nuts on the two square-neck bolts alternatively. After the main and auxiliary bracketsare secured properly, measure the spacing between the brackets on both sides and ensure thatthe spacing is the same on the two sides.Figure 8-23 Securing the RRU mounting brackets Step 4 Use an inner hexagon screwdriver to remove the attachment plate from one side of the RRU,reinstall the attachment plate onto the rear of the RRU, and tighten the four stainless screws to5 N·m (44.25 lbf·in.), as shown in Figure 8-24.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.66
Figure 8-24 Installing the attachment plate onto the rear of the RRU Step 5 Install the RRU onto the main bracket, as shown in Figure 8-25.Figure 8-25 Installing the RRU onto the main bracket Step 6 Use an inner hexagon screwdriver to tighten the captive screw into the holes on the top of theattachment plate and main bracket to 5 N·m (44.25 lbf·in.) so that the attachment plate and mainbracket are firmly secured, as shown in Figure 8-26.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.67
Figure 8-26 Securing the captive screw into the connection hole ----End8.4 Installing the RRU on Angle SteelThis section describes the procedure and precautions for installing the RRU on angle steel. AnRRU can be installed on angle steel secured on the ground or a tower. Each piece of angle steelallows only one RRU to be installed in standard or reverse mode.PrerequisitesBefore you install an RRU on angle steel secured on a tower, the RRU and its mounting bracketsare hoisted onto the tower. For details, see 7.1 Hoisting an RRU onto a Tower.The hoist clamp on the main bracket is secured properly.CAUTIONlDo not stand the RRU upright because the RF ports cannot support the weight of the RRU.lPlace a foam pad or cardboard under the RRU to protect the RRU housing from damageduring the installation.ContextFigure 8-27 shows the top view of the RRU installed on angle steel.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.68
Figure 8-27 Top view of the RRU(1) Angle steel ProcedureStep 1 Determine a position for installing the mounting brackets.lIf the RRU must be installed on angle steel secured on a tower, see 3.5.1 Clearance for aSingle RRU to determine a position.lIf the RRU must be installed on angle steel secured on the ground, see Figure 8-28 todetermine a position.Figure 8-28 Distance between the mounting brackets and the ground NOTEIt is recommended that the mounting brackets be installed at a height of 1200 mm (47.24 in.) to 1600mm (62.99 in.) above the ground.Step 2 Install the RRU mounting brackets, as shown in Figure 8-29.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.69
Figure 8-29 Installing the RRU mounting brackets NOTEVerify that the arrows on the mounting brackets are pointing up.1. Adjust the position of the nut and remove one end of the square-neck bolt from the slot onthe auxiliary bracket.2. Slide the mounting brackets onto the angle steel horizontally and insert the square-neckbolt into the slot.Step 3 Use a 16 mm (0.67 in.) M10 torque wrench to tighten the nuts to 40 N·m (354.03 lbf·in.) so thatthe mounting brackets are secured onto the angle steel, as shown in Figure 8-30.CAUTIONTighten the nuts on the two square-neck bolts alternatively. After the main and auxiliary bracketsare secured properly, measure the spacing between the brackets on both sides and ensure thatthe spacing is the same on the two sides.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.70
Figure 8-30 Securing the RRU mounting brackets Step 4 Use an inner hexagon screwdriver to remove the attachment plate from one side of the RRU,reinstall the attachment plate onto the rear of the RRU, and tighten the four stainless screws to5 N·m (44.25 lbf·in.), as shown in Figure 8-31.Figure 8-31 Installing the attachment plate onto the rear of the RRU Step 5 Install the RRU onto the main bracket, as shown in Figure 8-32.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.71
Figure 8-32 Installing the RRU onto the main bracket Step 6 Use an inner hexagon screwdriver to tighten the captive screw into the holes on the top of theattachment plate and main bracket to 5 N·m (44.25 lbf·in.) so that the attachment plate and mainbracket are firmly secured, as shown in Figure 8-33.Figure 8-33 Securing the captive screw into the connection hole ----EndRRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.72
8.5 Installing the RRU on a WallThis section describes the procedure and precautions for installing the RRU on a wall.PrerequisitesThe hoist clamp on the main bracket is secured properly.CAUTIONlDo not stand the RRU upright because the RF ports cannot support the weight of the RRU.lPlace a foam pad or cardboard under the RRU to protect the RRU housing from damageduring the installation.ContextThe wall on which RRUs are installed must meet the following requirements:lWhen a single RRU is installed, the wall must be capable of bearing at least four times theweight of the RRU.lExpansion anchor bolts must be tightened to 30 N·m (265.52 lbf·in.) so that the bolts staysecured without damaging the wall.ProcedureStep 1 Disassemble the RRU mounting brackets, as shown in Figure 8-34.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.73
Figure 8-34 Disassembling the mounting brackets(1) Main bracket (2) Square-neck bolt (3) Pole installation bracket (4) Auxiliary bracket(5) Flat washer (6) Spring washer (7) Nut (8) Plastic cap 1. Use an M6 inner hexagon torque screwdriver to remove the four inner hexagon screws onthe pole installation bracket, and remove the main bracket from the pole installation bracket.2. Use an M10 torque wrench to loosen the nuts on the two square-neck bolts, and removethe plastic cap, nuts, spring washers, flat washers, square-neck bolts, and pole installationbracket from the auxiliary bracket.Step 2 Place the pole installation bracket against the installation position, use a level to verify that thepole installation bracket is placed horizontally, and then mark anchor points with a marker, asshown in Figure 8-35.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.74
Figure 8-35 Marking anchor points(1) Level (2) Pole installation bracket (3) RRU NOTEIt is recommended that the pole installation bracket be installed at a height of 1200 mm (47.24 in.) to 1600mm (62.99 in.) above the ground.Step 3 Drill holes at the anchor points, and then insert expansion anchor bolt assemblies, as shown inFigure 8-36.Figure 8-36 Drilling a hole and inserting expansion anchor bolt assemblies(1) M10x80 bolt (2) Nut (3) Spring washer (4) Flat washer (5) Expansion tube RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.75
1. Use a hammer drill with a Ф12 bit to drill holes vertically at the marked anchor points.Ensure that the depth of each hole ranges from 55 mm (2.17 in.) to 60 mm (2.36 in.).CAUTIONTake proper safety measures to protect your eyes and respiratory tract against the dustbefore drilling holes.2. Tighten the expansion anchor bolts slightly and place one vertically into each hole.3. Use a rubber mallet to pound the expansion anchor bolt until it goes all the way into thehole.4. Tighten and then loosen the expansion bolt, and remove the M10 bolt, spring washer, andflat washer in sequence.CAUTIONAfter dismantling an expansion anchor bolt, ensure that the top of the expansion tube is onthe same level as the wall. Otherwise, the device cannot be installed on the wall evenly andsecurely.Step 4 Install the pole installation bracket on the expansion anchor bolts, place the flat washers, springwashers, and nuts through the expansion anchor bolts in sequence, and then use a 16 mm (0.63in.) torque socket to tighten the nuts to 30 N·m (265.52 lbf·in.), as shown in Figure 8-37.Figure 8-37 Installing the pole installation bracket on the expansion anchor bolts RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.76
CAUTIONVerify that the arrows on the pole installation bracket are pointing up.Step 5 Install the main bracket onto the pole installation bracket, and use an inner hexagon screwdriverto tighten four M6x16 inner hexagon screws to 5 N·m (44.25 lbf·in.) so that the main bracketand pole installation bracket are firmly secured, as shown in Figure 8-38.Figure 8-38 Installing the main bracket (1) Main bracket (2) Pole installation bracketStep 6 Use an inner hexagon screwdriver to remove the attachment plate from one side of the RRU,reinstall the attachment plate onto the rear of the RRU, and tighten the four stainless screws to5 N·m (44.25 lbf·in.), as shown in Figure 8-39.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.77
Figure 8-39 Installing the attachment plate onto the rear of the RRU Step 7 Install the RRU onto the main bracket, as shown in Figure 8-40.Figure 8-40 Installing the RRU onto the main bracket Step 8 Use an inner hexagon screwdriver to tighten the captive screw into the holes on the top of theattachment plate and main bracket to 5 N·m (44.25 lbf·in.) so that the attachment plate and mainbracket are firmly secured, as shown in Figure 8-41.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.78
Figure 8-41 Securing the captive screw into the connection hole ----End8.6 Installing an RRU on an IFS06This section describes the procedure and precautions for installing an RRU on an IFS06.PrerequisitesThe hoist clamp on the main bracket is secured properly.CAUTIONlDo not stand the RRU upright because the RF ports cannot support the weight of the RRU.lPlace a foam pad or cardboard under the RRU to protect the RRU housing from damageduring the installation.ContextlThe upper and lower adjustable beams on an IFS06 can be moved up and down to fit forheights of RRUs.lRRUs can be installed on an IFS06 only when the ambient temperature is higher than orequal to the lowest working temperature of the RRU and at least 5°C (41°F) lower than thehighest working temperature of the RRU. In this scenario, the IFS06 supports at least threeRRUs. When the ambient temperature is higher than or equal to the lowest workingtemperature of the RRU and at least 10°C (50°F) lower than the highest workingtemperature of the RRU, the IFS06 supports a maximum of six RRUs.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.79
NOTEFor details about the operating temperature of the RRU, see section "Technical Specifications ofRRUs" in 3900 Series Base Station Technical Description.lInstall RRUs in the sequence from bottom to top and from left to right.lThis section describes how to install an RRU in height-unrestricted scenarios. Theprocedure for installing an RRU in height-restricted scenarios is the same as that in height-unrestricted scenarios.lWhen installing the pole installation bracket, you need to use the M10x50 bolts deliveredwith the IFS06.lRubber washers are easily compressed or broken, whereas do not need to be replaced.ProcedureStep 1 Disassemble the RRU mounting brackets, as shown in Figure 8-42.Figure 8-42 Disassembling the mounting brackets(1) Main bracket (2) Square-neck bolt (3) Pole installation bracket (4) Auxiliary bracket(5) Flat washer (6) Spring washer (7) Nut (8) Plastic cap 1. Use an M6 inner hexagon torque screwdriver to remove the four inner hexagon screws onthe pole installation bracket, and remove the main bracket from the pole installation bracket.2. Use an M10 torque wrench to loosen the nuts on the two square-neck bolts, and removethe plastic cap, nuts, spring washers, flat washers, square-neck bolts, and pole installationbracket from the auxiliary bracket.Step 2 Use the M10x50 bolts delivered with the IFS06 to secure the pole installation bracket to theIFS06, and then use an M10 torque socket wrench to secure the bolts to 30 N·m (265.52 lbf·in.).RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.80
CAUTIONEnsure that the arrows on the pole installation bracket are pointing up.lHeight-restricted scenariosUse one finger to push and remove the rubber plugs on the beam and then install the poleinstallation bracket, as shown in Figure 8-43.Figure 8-43 Installing the pole installation bracket in height-restricted scenarios(1) Spring washer (2) Rubber washerlHeight-unrestricted scenariosInstall the pole installation bracket, as shown in Figure 8-44.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.81
Figure 8-44 Installing the pole installation bracket in height-unrestricted scenarios(1) Spring washer (2) Rubber washerStep 3 Attach the main bracket to the pole installation bracket, and use an inner hexagon screwdriverto tighten four M6x16 screws to 5 N·m (44.25 lbf·in.) so that the main bracket and poleinstallation bracket are firmly secured, as shown in Figure 8-45.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.82
Figure 8-45 Installing the main bracket(1) Main bracket (2) Pole installation bracket Step 4 Attach the RRU to the main bracket, and then use an inner hexagon screwdriver to tighten thecaptive screw into the holes of the attachment plate and main bracket to 5 N·m (44.25 lbf·in.) sothat the attachment plate and main bracket are firmly secured, as shown in Figure 8-46.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.83
Figure 8-46 Installing the RRU onto the main bracket Step 5 Install the RRUs on the lower level from left to right, as shown in Figure 8-47.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.84
Figure 8-47 Installing RRUs on the lower level Step 6 Optional: When the ambient temperature is equal to or higher than the lowest operatingtemperature of the RRU and at least 10°C (10°F) lower than the highest operating temperatureof the RRU, repeat the preceding steps to install the RRUs on the higher level, as shown inFigure 8-48.RRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.85
Figure 8-48 Installing RRUs on the higher level----EndRRU3268Installation Guide 8 Installing the RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.86
9 Installing RRU CablesAbout This ChapterThis chapter describes the procedure for installing RRU cables.9.1 Cabling RequirementsCables must be routed according to the specified cabling requirements to prevent signalinterference.9.2 Cable ConnectionsThis section describes the cable connections for a single RRU and multiple RRUs.9.3 Installation ProcessThis section describes the process of installing RRU cables.9.4 RRU Cable ListThis section describes RRU cable connections.9.5 Installing an RRU PGND CableThis section describes the procedure for installing an RRU PGND cable.9.6 Installing an RRU RF JumperThis section describes the procedure for installing an RRU RF jumper.9.7 Installing an RRU AISG Multi-Wire Cable and AISG Extension CableThis section describes the procedures for installing an RRU AISG multi-wire cable and AISGextension cable.9.8 Installing an RRU Alarm CableThis section describes the procedure for installing an RRU alarm cable.9.9 Opening the Cover Plate of an RRU Cabling CavityThis section describes the procedure for opening the cover plate of an RRU cabling cavity.9.10 Installing an RRU Power CableThis section describes the procedure for installing an RRU power cable.9.11 Installing a CPRI Fiber Optic CableThis section describes the procedure for installing a CPRI fiber optic cable.9.12 Closing the Cover Plate of an RRU Cabling CavityRRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.87
This section describes the procedure for closing the cover plate of an RRU cabling cavity.RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.88
9.1 Cabling RequirementsCables must be routed according to the specified cabling requirements to prevent signalinterference.NOTEIf a cable listed below is not required, skip the routing requirements of the cable.General Cabling RequirementsRequirements for Bending RadiuslThe bending radius of the 7/8'' feeder must be more than 250 mm (9.84 in.), and the bendingradius of the 5/4'' feeder must be more than 380 mm (14.96 in.).lThe bending radius of the 1/4'' jumper must be more than 35 mm (1.38 in.). The bendingradius of the super-flexible 1/2'' jumper must be more than 50 mm (1.97 in.), and the bendingradius of the ordinary 1/2'' jumper must be more than 127 mm (5 in.).lThe bending radius of the power cable or PGND cable must be at least three times thediameter of the cable.lThe bending radius of a fiber optic cable is at least 20 times the diameter of the fiber opticcable, and the minimum bending radius of the breakout cable at each end of the fiber opticcable is 30 mm (1.18 in.).lThe bending radius of the E1/T1 cable must be at least three times the diameter of the cable.lThe bending radius of the signal cable must be at least five times the diameter of the cable.Requirements for Cable BindinglThe same types of cable must be bound together.lDifferent types of cable must be separately routed with the minimum spacing of 30 mm(1.18 in.) and cannot be entangled.lThe cables must be bound tightly and neatly. The sheaths of the cables must not be damaged.lCable ties are installed in the same direction, and those at the same horizontal line must bein a straight line.lThe excess of indoor cable ties is trimmed off, and the excess of outdoor cable ties allowsabout 5 mm (0.2 in.), without remaining rough edges.lLabels or nameplates must be attached to both ends, joints, or turns of cables after they areinstalled.Security RequirementslCables should be placed away from sharp objects or wall burrs. If these positions areinevitable, protect the cables with protection pipes.lCables must be routed away from heat sources, or heat-insulation materials are addedbetween cables and heat sources.lSufficient slack (recommended for about 0.1 m [0.33 ft]) is provided in cables at turns orthe position close to a device, facilitating cable and device maintenance.Indoor Cabling RequirementslCables are routed indoors through the feeder window.RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.89
lDrip loops must be made outside the feeder window, and the requirements for the minimumbending radius are met.lWhen cables are routed indoors, engineers are required indoors for cooperation.lThe feeder window must be waterproofed.Outdoor Cabling RequirementslCables routed outdoors must be led through a pipe when they may be damaged.lAC power cables, transmission cables, and cables buried in the ground must be protected.lIf cables at the cabinet bottom need to be routed through a pipe along the ground, lead thepipe into the cabinet base for about 30 mm (1.18 in.) to 50 mm (1.97 in.), not into thecabinet. Block the pipe with waterproof tape or silicon gel, and secure the pipe to the cablehole at the cabinet bottom with metal piece.lIf cables at the cabinet bottom need to be routed through a pipe along the metal cable trough,do not lead the pipe into the cabinet base. The cable trough must be sealed and routedthrough the cable hole at the cabinet bottom.lCables are secured with cable clips.lCables are routed neatly along the specified cabling direction and secured with cable clips.lThe positions for cable clips are determined onsite. For example, the cable clips for the7/8" feeder are installed at the spacing of 1.5 m (4.92 ft) to 2 m (6.56 ft) in the same direction,and the cable clips for the power cables are installed at the spacing of 1.5 m (4.92 ft) to 2m (6.56 ft) in the same direction.lCable clips must be vertical with cables, and the cables in a cable clip must be parallel.lAfter routing cables neatly and correctly, tighten the screws on cable clips.Secure cables on the cable tray, as shown in Figure 9-1.Figure 9-1 Securing cables on the cable trayRRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.90
 Secure cables on the tower, as shown in Figure 9-2.Figure 9-2 Securing cables on the tower Special Cabling RequirementsCabling Requirements for Power CableslPower cables must be installed in the position specified in engineering design documents.lIf the length of power cables is insufficient, replace the cables rather than adding connectorsor soldering joints to lengthen the cables.lCables must be routed by only qualified and trained personnel before all preparations aremade.lCables are routed in an untangled and orderly fashion.RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.91
lIf DC power cables need to be routed on the tower platform, lay out the cables on theguardrail with the shortest distance and route the cables along the guardrail.lIf DC power cables need to be routed close to a device on the tower, secure the cables tothe guardrail or pole with cable clips. The device cannot be far away from the position forsecuring the cables.Cabling Requirements for PGND CableslPGND cables for the base station must be connected to the same ground bar.lPGND cables must be buried in the ground or routed indoors. They should not be routedoverhead before they are led into the equipment room.lThe exterior of the coaxial wire and the shield layer of the shielded cable must have properelectrical contact with the metal surface of the equipment to which they are connected.lPGND cables and signal cables must be installed in an untangled and orderly fashion. Acertain distance must be reserved between them to prevent interference from each other.lFuses or switches must not be installed on the PGND cables.lOther devices must not be used for electrical connections of the PGND cables.lAll the metal parts in the housing of the equipment must be reliably connected to the groundterminal.Cabling Requirements for E1 CableslE1 cables must not cross power cables, PGND cables, or RF cables when routed. Iftransmission cables are routed with power cables, PGND cables, or RF cables in parallel,the spacing between them must be greater than 30 mm (1.18 in.).lE1 cables are routed straightly and bound neatly with cable ties.lSufficient slack is provided in E1 cables at turns.lE1 cables cannot be squeezed by the cabinet door when routed through the cabinet, asshown in Figure 9-3.Figure 9-3 E1 cables routed through the cabinet Cabling Requirements for Fiber Optic CableslFiber optic cables must be routed by at least three qualified and trained personnel beforeall preparations are made.RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.92
lFiber optic cables are used within the temperature range of -40°C to 60°C. If the currenttemperature is out of the range, make protection measures or route the cables again.lCables are routed in an untangled and orderly fashion.lDo not bind fiber optic cables at turns.lDo not stretch, step on, or place heavy objects on fiber optic cables. Keep the cables awayfrom sharp objects.lWhen fiber optic cables are routed, the excess of the cables must be coiled around specialdevices, such as a fiber coiler.lWhen coiling fiber optic cables, apply even strength. Do not bend the cables with force.lVacant optical connectors must be covered with dustproof caps.lFiber optic cables cannot be squeezed by the cabinet door when routed through the cabinet,as shown in Figure 9-4, Figure 9-5 and Figure 9-6.Figure 9-4 CPRI fiber optic cables routed through the cabinet (1) Figure 9-5 CPRI fiber optic cables routed through the cabinet (2) RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.93
Figure 9-6 FE/GE cables routed through the cabinet lIf fiber optic cables need to be routed on the tower platform, lay out the cables on theguardrail with the shortest distance and route the cables along the guardrail.lIf fiber optic cables need to be routed close to a device on the tower, secure the cables tothe guardrail or pole with cable clips. The device cannot be far away from the position forsecuring the cables.lIf the fiber optic cables close to a device are too long, coil the excess of the cables andsecure them on the tower.9.2 Cable ConnectionsThis section describes the cable connections for a single RRU and multiple RRUs.NOTElA lower-level RRU obtains power directly from the external power system, but not from an upper-level RRU using a power cable.Figure 9-7 shows the cable connections for a single RRU.RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.94
Figure 9-7 Cable connections for a single RRU(1) PGND cable (2) RRU RF jumper (3) RRU AISG multi-wire cable(4) RRU AISG extension cable (5) RRU power cable (6) CPRI fiber optic cable(7) RRU alarm cable - - Figure 9-8 shows the cable connections for multiple RRUs.RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.95
Figure 9-8 Cable connections for multiple RRUs(1) PGND cable (2) RRU RF jumper (3) RRU power cable(4) CPRI fiber optic cable - - 9.3 Installation ProcessThis section describes the process of installing RRU cables.Figure 9-9 shows the process of installing RRU cables.RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.96
Figure 9-9 Process of installing RRU cables 9.4 RRU Cable ListThis section describes RRU cable connections.Table 9-1 lists RRU cables.Table 9-1 RRU cablesCable One End The Other EndConnector InstallationPositionConnector InstallationPositionRRU PGNDCableOT terminal (16mm2 or 0.025 in.2, M6)Groundterminal on theRRUOT terminal (16mm2 or 0.025 in.2, M8)Ground terminalon the ground barRRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.97
Cable One End The Other EndConnector InstallationPositionConnector InstallationPositionRRU PowerCableTool-less femaleconnector(pressfit type)NEG(-) andRTN(+) portson the RRUTool-less femaleconnector(pressfit type)One of RRU0 toRRU5 ports onthe EPU or EPSOne of LOAD0 toLOAD5 ports onthe DCDU-11BOT terminal (3.3mm2 or 0.005 in.2, M4),complying withNorth AmericanstandardsOT terminal (4mm2 or 0.006 in.2, M4),complying withEuropeanstandardsOne of LOAD0 toLOAD5 ports onthe DCDU-03BRRU AlarmCableDB15 waterproofmale connectorEXT_ALMport on theRRUCord endterminalExternal alarmdeviceCPRI FiberOptic CableDLC connector CPRI0 port onthe RRUDLC connector CPRI port on theWBBP in theBBUCPRI1 port onthe RRUCPRI0 port on theRRURRU RFJumperDIN maleconnectorANT_TX/RXA orANT_TX/RXB port onthe RRUDIN maleconnectorAntenna systemRRU AISGMulti-WireCableDB9waterproofedmale connectorRET port onthe RRUStandard AISGfemale connectorStandard AISGmale connectoron the RCU or onthe AISGextension cableRRU AISGExtensionCableStandard AISGmale connectorStandard AISGfemaleconnector onthe AISGmulti-wirecableStandard AISGfemale connectorStandard AISGmale connectoron the RCURRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.98
 9.5 Installing an RRU PGND CableThis section describes the procedure for installing an RRU PGND cable.ContextThe cross-sectional area of an RRU PGND cable is 16 mm2 (0.025 in.2). The cable has an M6OT terminal at one end and an M8 terminal at the other end.ProcedureStep 1 According to the actual cable route, cut the PGND cable into a proper length to prepare an RRUPGND cable. Then add an OT terminal at each end of the cable according to the instructions inAssembling the OT Terminal and the Power Cable.Step 2 Install the RRU PGND cable.Connect the M6 OT terminal at one end of the PGND cable to the ground terminal at the RRUbottom and the M8 OT terminal at the other end to the external ground bar, as shown in Figure9-10.Figure 9-10 Installing an RRU PGND cable NOTECrimp OT terminals in correct positions, as shown in Figure 9-11.RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.99
Figure 9-11 Correct position of an OT terminal Step 3 Label the installed cables according to the instructions in Attaching a Cable-Tying Label.----End9.6 Installing an RRU RF JumperThis section describes the procedure for installing an RRU RF jumper.ProcedureStep 1 Connect the DIN male connector at one end of the RRU RF jumper to the ANT port on the RRU,and use a torque wrench to tighten the connector to 25 N·m (221.27 lbf·in.), as shown in Figure9-12.Figure 9-12 Installing an RRU RF jumper RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.100
CAUTIONOn AC-powered electric railways, such as high speed railways, when leaky cables are connectedto RRUs installed in tunnels, high-voltage-resistance DC blocks must be installed between RRURF jumpers and the leaky cables to protect the RRUs against damage.Step 2 Link the other end of the RF jumper to the external antenna system.Step 3 Waterproof the connectors of the RF jumper by referring to Figure 9-13.Figure 9-13 Waterproofing a connector of the RF jumper (1) Waterproof tape (2) PVC insulation tapeNOTElBefore wrapping waterproof tape, stretch the tape evenly until the length of the tape becomes twice itsoriginal length.lDo not stretch the PVC insulation tape when wrapping the PVC insulation tape.lWrap each layer of tape around the connector tightly and neatly, and ensure that each layer of tape overlapsmore than 50% of the preceding layer. Ensure that neighboring layers are stuck to each other.lEnsure that the adhesive surface of the tape overlaps the lower layer.lWhen cutting off the cable ties, reserve a redundant length of 3 mm (0.12 in.) to 5 mm (0.2 in.).1. Wrap three layers of waterproof tape on the connector, first from bottom up, then from topdown, and finally from bottom up. Start wrapping the connector at a position 50 mm (1.97in.) away below the bottom of the connector to the top of the connector, first from bottomRRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.101
up, then from top down, and finally from bottom up. Cut off the redundant tape after threelayers are wrapped. Wrap each layer of tape around the connector tightly.2. Wrap three layers of PVC insulation tape. Start the wrapping at a position 30 mm (1.18 in.)away below the bottom of the waterproof tape to the top of the connector, first from bottomup, then from top down, and finally from bottom up. Cut off the redundant tape after threelayers are wrapped. Wrap each layer of tape around the connector tightly.3. Start binding cable ties to the cable at a position 3 mm (0.12 in.) to 5 mm (0.2 in.) awayfrom one end of the PVC insulation tape.Step 4 Check the dustproof caps on antenna connectors. In outdoor scenarios, dustproof caps must bewaterproofed, as shown in Figure 9-14.CAUTIONDo not remove dustproof caps from vacant antenna connectors.Figure 9-14 Waterproofing a dustproof cap(1) Dustproof cap (2) Waterproof tape (3) PVC insulation tapeNOTElBefore wrapping waterproof tape, stretch the tape evenly until the length of the tape becomes twice itsoriginal length.lDo not stretch the PVC insulation tape when wrapping the PVC insulation tape.lWrap each layer of tape around the connector tightly and neatly, and ensure that each layer of tape overlapsmore than 50% of the preceding layer. Ensure that neighboring layers are stuck to each other.lEnsure that the adhesive surface of the tape overlaps the lower layer.lWhen cutting off the cable ties, reserve a redundant length of 3 mm (0.12 in.) to 5 mm (0.2 in.). 1. Verify that dustproof caps are not removed.2. Wrap three layers of waterproof tape on the connector, first from bottom up, then from topdown, and finally from bottom up. Wrap each connector with three layers of waterprooftape, from bottom up, then from top down, and finally from bottom up. Do not cut the tapeuntil all the three layers of the tape are already wrapped. Cut off the redundant tape afterthree layers are wrapped. Wrap each layer of tape around the connector tightly.RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.102
3. Wrap three layers of PVC insulation tape. Wrap each connector with three layers ofwaterproof tape, from bottom up, then from top down, and finally from bottom up. Do notcut the tape until all the three layers of the tape are already wrapped. Cut off the redundanttape after three layers are wrapped. Wrap each layer of tape around the connector tightly.4. Start binding cable ties to the cable at a position 3 mm (0.12 in.) to 5 mm (0.2 in.) awayfrom one end of the PVC insulation tape.Step 5 Route the cables according to the instructions in 9.1 Cabling Requirements, and then use cableties to bind the cables.Step 6 Label the installed cables according to the instructions in Attaching a Sign Plate Label.Step 7 Attach color-coding to the installed RF jumper according to the instructions in Attaching theColor Ring.----End9.7 Installing an RRU AISG Multi-Wire Cable and AISGExtension CableThis section describes the procedures for installing an RRU AISG multi-wire cable and AISGextension cable.ContextWhen the distance between an RRU and a Remote Control Unit (RCU) is longer than 5 m (16.4ft.), an AISG multi-wire cable is not long enough to connect the RRU and the RCU. In this case,an AISG extension cable is used to extend the AISG multi-wire cable.ProcedurelInstall an AISG multi-wire cable that is not configured with an AISG extension cable.1. Use an M3 flat-head screwdriver to loosen the screws on the dustproof cap on the RETport and remove the dustproof cap.2. Link the waterproofed DB9 connector at one end the AISG multi-wire cable to theRET port on the RRU bottom, as shown in Figure 9-15.RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.103
Figure 9-15 Installing an RRU AISG multi-wire cable 3. Use an M3 Phillips screwdriver to tighten the posts on both sides of the waterproofDB9 connector to 0.4 N·m (3.54 lbf·in.).4. Connect the other end of the cable to the standard AISG male connector on the RCU.5. Route the cables according to the instructions in 9.1 Cabling Requirements, and thenuse cable ties to bind the cables.6. Label the installed cables according to the instructions in Attaching an L-ShapedLabel.lInstall an AISG multi-wire cable that is configured with an AISG extension cable.1. Use an M3 flat-head screwdriver to loosen the screws on the dustproof cap on the RETport and remove the dustproof cap.2. Link the waterproofed DB9 connector at one end of the AISG multi-wire cable to theRET port on the RRU bottom, and link the other end to the standard AISG maleconnector of the AISG extension cable, as shown in Figure 9-16.RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.104
Figure 9-16 Installing an RRU AISG multi-wire cable 3. Use an M3 Phillips screwdriver to tighten the posts on both sides of the waterproofDB9 connector to 0.4 N·m (3.54 lbf·in.).4. Connect the other end of the AISG extension cable to the standard AISG maleconnector on the RCU, as shown in Figure 9-17.Figure 9-17 Installing an RRU AISG extension cableRRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.105
 5. Route the cables according to the instructions in 9.1 Cabling Requirements, and thenuse cable ties to bind the cables.6. Label the installed cables according to the instructions in Attaching an L-ShapedLabel.----End9.8 Installing an RRU Alarm CableThis section describes the procedure for installing an RRU alarm cable.ProcedureStep 1 Use an M3 Phillips screwdriver to loosen the screws on the dustproof cap on the EXT_ALMport and remove the dustproof cap.Step 2 Connect the waterproof DB15 connector at one end of the RRU alarm cable to the EXT_ALMport on the RRU, and connect the eight cord end terminals at the other end to external alarmdevices, as shown in Figure 9-18.Figure 9-18 Installing an RRU alarm cable Step 3 Use an M3 Phillips screwdriver to tighten the posts on both sides of the waterproof DB15 maleconnector to 0.4 N·m (3.54 lbf·in.).Step 4 Route the cables according to the instructions in 9.1 Cabling Requirements, and then use cableties to bind the cables.RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.106
Step 5 Label the installed cables according to the instructions in Attaching an L-Shaped Label.----End9.9 Opening the Cover Plate of an RRU Cabling CavityThis section describes the procedure for opening the cover plate of an RRU cabling cavity.ProcedureStep 1 Wear ESD gloves.CAUTIONTake proper ESD protection measures, for example, wear ESD gloves, to prevent electrostaticdamage to the boards, modules, or electronic components.Step 2 Use an M5 Phillips screwdriver to loosen the three screws on the cover plate of the RRU cablingcavity, and open the cover plate, as shown in Figure 9-19.Figure 9-19 Opening the cover plate of the RRU cabling cavity(1) Cover plate (2) Cabling cavity (3) Clip(4) Cable trough for the power cable (5) Waterproof block (6) Cable trough for the fiber optic cable Step 3 Loosen the screws on the clip, and open the clip, as shown Figure 9-20.RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.107
NOTEOpen the clip only for the associated cable.Figure 9-20 Opening clips Step 4 Remove the waterproof block.NOTERemove only the waterproof blocks for the cables to be installed.----End9.10 Installing an RRU Power CableThis section describes the procedure for installing an RRU power cable.PrerequisiteslAn easy power receptacle (pressfit type) connector is added to the RRU power cable onthe RRU side. For details, see 12.1 Adding a Tool-Less Female Connector (PressfitType) to the RRU Power Cable on the RRU Side.lAdd a connector or OT terminals to the RRU power cable on the power device side. Fordetails, see the DBS3900 Installation Guide.ContextThere are two types of RRU power cables in terms of cross-sectional areas: 3.3 mm2 (0.005 in.2) (12 AWG) complying with North American standards and 4 mm2 (0.006 in.2) complying withEuropean standards.RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.108
Table 9-2 describes the power cable connections.Table 9-2 Power cable connectionsCablePowerDeviceOne End The Other End RemarksConnector InstallationPositionConnector InstallationPositionRRUpowercableDCDU-11BTool-less femaleconnector(pressfit type)Powerporton anRRUTool-less femaleconnector(pressfit type)One of theLOAD0 toLOAD5 portson theDCDU-11BBlackEPU One of theRRU0 toRRU5 ports onthe EPU WARNINGWhen installing the RRU power cable, connect the RRU power cable first to the RRU and thento the power device. Operations in the reverse sequence may cause damage to the componentsand injury of human bodies.ProcedureStep 1 Connect the tool-less female connector (pressfit type) at one end of the RRU power cable to thepower supply socket on the RRU, as shown in Figure 9-21.RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.109
Figure 9-21 Installing an RRU power cable CAUTIONEnsure that the exposed shield layer of the power cable is properly tightened using the clip.Step 2 Connect the tool-less female connector (pressfit type) at the other end of the RRU power cableto the corresponding position on the power device.NOTElA DCDU-11B can supply power to a maximum of six RRUs. The RRU power cables are connectedto the LOAD0 to LOAD5 terminals on the DCDU-11B.lAn EPU can supply power to a maximum of six RRUs. The RRU power cables are connected to theRRU0 to RRU5 ports on the EPU.lWhen the RRU power cable is connected to the EPU, the blue core wire in the tool-less female connector(pressfit type) is connected to the left part of a port on the EPU, and the black/brown core wire isconnected to the right part of the port on the EPU.Step 3 Route the cables according to the instructions in 9.1 Cabling Requirements, and then use cableties to bind the cables.Step 4 Label the installed cables according to the instructions in Attaching a Cable-Tying Label.----End9.11 Installing a CPRI Fiber Optic CableThis section describes the procedure for installing a CPRI fiber optic cable.RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.110
PrerequisitesBefore the installation, single-mode optical modules can be distinguished from multi-modeoptical modules in either of the following ways:lSM and MM labels on an optical module: SM indicates a single-mode optical module, andMM indicates a multi-mode optical module.lColor of the puller on an optical module: Blue indicates a single-mode optical module, andblack or gray indicates a multi-mode optical module.CAUTIONThe optical modules to be installed must match CPRI rates.ContextlA CPRI fiber optic cable transmits CPRI signals between a BBU and an RRU.lFor details about CPRI fiber optic cable connections, see section "CPRI Cable Connections"in the BBU3900 Hardware Description or DBS3900 Hardware Description.ProcedureStep 1 Lower the pullers of two optical modules, insert one optical module into the CPRI0 port on theRRU and the other optical module into the CPRI port on the BBU, and raise the pullers, as shownin Figure 9-22.Figure 9-22 Installing an optical moduleCAUTIONThe performance of an optical module that is exposed to the air for more than 20 minutes maybe abnormal. Therefore, you must insert an fiber optic cable into an unpacked optical modulewithin 20 minutes.Step 2 Connect the end labeled 1A and 1B of the fiber optic cable to the optical module on the RRUside, as shown in Figure 9-23.RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.111
Figure 9-23 Installing a CPRI fiber optic cableCAUTIONlTo avoid any damage to fiber optic cables, the cables connected to the RRU must be installedaccording to the installation process. For details about the installation process, see 9.3Installation Process.Step 3 Connect the end labeled 2A and 2B of the fiber optic cable to the optical module on the BBUside.Step 4 Route the cables according to the instructions in 9.1 Cabling Requirements, and then use cableties to bind the cables.Step 5 Label the installed cables according to the instructions in Attaching an L-Shaped Label.----End9.12 Closing the Cover Plate of an RRU Cabling CavityThis section describes the procedure for closing the cover plate of an RRU cabling cavity.RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.112
ProcedureStep 1 Close the clips for the installed cables. Use a torque screwdriver to tighten the screws on eachclip to 1.4 N·m (12.39 lbf·in.), as shown in Figure 9-24.CAUTIONEnsure that the exposed shield layer of the power cable is properly tightened using the clip.Figure 9-24 Closing clips Step 2 Insert waterproof blocks into vacant cable troughs in the cabling cavity, as shown in Figure9-25.CAUTIONEnsure that cables and waterproof blocks are properly inserted into troughs.RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.113
Figure 9-25 Correct placement of waterproof blocks Step 3 Close the cover plate of the RRU cabling cavity. Use an M5 torque screwdriver to partiallytighten the screws on the cover plate in the sequence shown in Figure 9-26. Then tighten thescrews to 2 N·m (17.7 lbf·in.) in the same sequence.Figure 9-26 Closing the cover plate of an RRU cabling cavity RRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.114
Step 4 Take off the ESD gloves, and pack up all the tools.----EndRRU3268Installation Guide 9 Installing RRU CablesIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.115
10 Checking the RRU HardwareInstallationAfter an RRU is installed, check the hardware installation.Table 10-1 provides the checklist for the RRU hardware installation.Table 10-1 Checklist for the RRU hardware installationSN Item1The position for each device conforms to the engineering drawing and meets thespace requirement. Sufficient space is reserved for equipment maintenance.2 The RRU is securely installed.3 The cover plate is securely installed on the RRU cabling cavity.4 Waterproof blocks are securely installed in vacant cable troughs of the RRU cablingcavity, and the cover plate for the cabling cavity is securely installed. In addition,vacant RF ports are covered with dustproof caps and the caps are tightened.5 There are no connectors or joints on each power cable or PGND cable.6 The terminals at two ends of each power cable or PGND cable are securely solderedor crimped.7 None of power cables and PGND cables can be short-circuited or reverselyconnected. In addition, these cables are not damaged or broken.8 Power cables and PGND cables are separately bound from other cables.9 The protection grounding of the RRU and the surge protection grounding of thebuilding share one group of ground conductors.10 The connectors of each signal cable are intact and securely linked, and these cablesare not damaged or broken.11 Labels are correct, legible, and complete at both ends of each cable, feeder, andjumper.RRU3268Installation Guide 10 Checking the RRU Hardware InstallationIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.116
11 Powering On an RRUAfter all the devices are installed, check the power-on status of an RRU.CAUTIONAfter you unpack an RRU, you must power on it within 24 hours. If you power off the RRU formaintenance, you must restore power to the RRU within 24 hours.Figure 11-1 shows the RRU power-on check process.NOTEFor details about how to power on an RRU, see Powering On an RRU. For details about how to power offan RRU, see section "Powering-Off the RRU" in RRU Maintenance Guide.RRU3268Installation Guide 11 Powering On an RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.117
Figure 11-1 RRU power-on check process(a) The normal input voltage of an RRU is -48 V DC. The voltage of the external power supply should rangefrom -36 V DC to -57 V DC.(b) The RUN indicator on the RRU is on for 1s and off for 1s. The ALM indicator is steady off.RRU3268Installation Guide 11 Powering On an RRUIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.118
12 AppendixAbout This ChapterThis section describes the procedure for adding an easy power receptacle (pressfit type)connector.12.1 Adding a Tool-Less Female Connector (Pressfit Type) to the RRU Power Cable on theRRU SideThis section describes the procedure for adding a tool-less female connector (pressfit type) tothe RRU power cable on the RRU side.RRU3268Installation Guide 12 AppendixIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.119
12.1 Adding a Tool-Less Female Connector (Pressfit Type)to the RRU Power Cable on the RRU SideThis section describes the procedure for adding a tool-less female connector (pressfit type) tothe RRU power cable on the RRU side.ContextFigure 12-1 shows the cable diagram on labels.Figure 12-1 Cable diagram on labels(1) Cable diagram on labels ProcedureStep 1 Determine the length of the power cable for different operations based on the labels, as shownin Figure 12-2.Figure 12-2 Determining the length of the power cableRRU3268Installation Guide 12 AppendixIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.120
 Step 2 Strip the specified length of the sheath off the power cable, as shown in Figure 12-3.Figure 12-3 Stripping the specified length of sheath Step 3 Strip a specified length of sheath off each core wire. The length must be consistent with thelength of the notch in the tool-less female connector (pressfit type), as shown in Figure 12-4.Figure 12-4 Stripping the sheath off each core wire Figure 12-5 Matched length Step 4 Add a tool-less female connector (pressfit type) to two core wires.1. Tighten the screws using a Phillips screwdriver, as shown in Figure 12-6.RRU3268Installation Guide 12 AppendixIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.121
Figure 12-6 Tightening screws 2. Connect the blue core wire labeled NEG(-) to the - port and the black/brown core wirelabeled RTN(+) to the + port on the tool-less female connector (pressfit type), and thentighten the screws using a Phillips screwdriver, as shown in Figure 12-7.Figure 12-7 Adding a tool-less female connector (pressfit type) to two core wires Step 5 Strip the specified length of the sheath off the power cable to expose the intact shield layer, asshown in Figure 12-8.Figure 12-8 Stripping the sheath off the power cable RRU3268Installation Guide 12 AppendixIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.122
CAUTIONEach core wire is exposed outside the tool-less female connector (pressfit type) for 1.5 mm(0.059 [in.]), as shown in Figure 12-9.Figure 12-9 Inserting core wires into the tool-less female connector (pressfit type)----EndRRU3268Installation Guide 12 AppendixIssue () Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.123

Navigation menu