Huawei MU736 HSPA M.2 Module AT Command Interface Specification (V100R002 02, English)

2013-12-25

• Revision History
• 1 Introduction
  • 1.1 Scope
  • 1.2 Overview
  • 1.3 Organization
  • 1.4 Document Conventions
  • 1.5 AT Command Syntax
    • 1.5.1 AT Command Types
      • Table 1-1 Types of AT commands
    • 1.5.2 AT Command Parameter
    • 1.5.3 AT Command Description
      • Figure 1-1 Interaction between the TE and MT
      • Figure 1-2 Basic organization format of the AT command line
      • Figure 1-3 An example of returned value of the AT command
  • 1.6 Abort Attributes of AT Command
  • 1.7 Rules for Running AT Command
    • 1. Each interface should be functionally convergent.
    • 2. Each command line contains only one AT command and ends with a carriage return character. For the URC instruction or response reported from MT to TE, only one AT command is allowed in a command line. In principle, users are not allowed to run S3/S4...
    • 3. For an AT command that cannot be interrupted, after sending the AT command, the TE must wait until the MT responds to the AT command before sending the second AT command.
    • 4. For the AT command to which the response is given only after a long time, in order to prevent interference on other events, it is recommended to report the final execution result asynchronously. If the ME responds to the TE only after a long time o...
    • 5. A string refers to a byte stream (excluding the quotation marks or commas) that is placed inside double quotation marks. Special note should be specified if the byte stream need not be enclosed in double quotation marks.
    • 6. The current version does not support escape character. The code value of a data format in the UCS2 coding is reported as characters. For example, if the UCS2 code of a Chinese character is 0x553a, the 553a is reported.
    • 7. A possible response sent by the MT to the TE consists of Information text and Result code, in which Information text is optional and Result code is mandatory. The format of a possible response is controlled by the ATV command. For details, see the ...
• 2 General Commands
  • 2.1 ATV–Set the Response Format
    • 2.1.1 Command Syntax
    • 2.1.2 Interface Description
    • 2.1.3 Parameter Description
    • 2.1.4 Property Description
    • 2.1.5 Example
  • 2.2 ATI–Request Identification
    • 2.2.1 Command Syntax
    • 2.2.2 Interface Description
    • 2.2.3 Parameter Description
    • 2.2.4 Property Description
    • 2.2.5 Example
  • 2.3 AT+CGMI/AT+GMI–Request Manufacturer Identification
    • 2.3.1 Command Syntax
    • 2.3.2 Interface Description
    • 2.3.3 Parameter Description
    • 2.3.4 Property Description
    • 2.3.5 Example
  • 2.4 AT+CGMM/AT+GMM–Request Model Identification
    • 2.4.1 Command Syntax
    • 2.4.2 Interface Description
    • 2.4.3 Parameter Description
    • 2.4.4 Property Description
    • 2.4.5 Example
  • 2.5 AT+CGMR/AT+GMR–Request Software Version
    • 2.5.1 Command Syntax
    • 2.5.2 Interface Description
    • 2.5.3 Parameter Description
    • 2.5.4 Property Description
    • 2.5.5 Example
  • 2.6 AT+CGSN/AT+GSN–Request Product IMEI
    • 2.6.1 Command Syntax
    • 2.6.2 Interface Description
    • 2.6.3 Parameter Description
    • 2.6.4 Property Description
    • 2.6.5 Example
  • 2.7 AT+CSCS–Set the TE Character Set
    • 2.7.1 Command Syntax
    • 2.7.2 Interface Description
    • 2.7.3 Parameter Description
    • 2.7.4 Property Description
    • 2.7.5 Example
  • 2.8 AT+CIMI–Request IMSI
    • 2.8.1 Command Syntax
    • 2.8.2 Interface Description
    • 2.8.3 Parameter Description
    • 2.8.4 Property Description
    • 2.8.5 Example
• 3 Call Control Commands and Methods
  • 3.1 ATD–Originate a Data Service Call
    • 3.1.1 Command Syntax
    • 3.1.2 Interface Description
    • 3.1.3 Parameter Description
    • 3.1.4 Property Description
    • 3.1.5 Example
• 4 Network Service Related Commands
  • 4.1 AT+COPS–Select Operator
    • 4.1.1 Command Syntax
    • 4.1.2 Interface Description
    • 4.1.3 Parameter Description
    • 4.1.4 Property Description
    • 4.1.5 Example
      • 1. Obtaining available operator list
      • 2. Automatic selection
      • 3. Manual selection
      • 4. Requesting network state
  • 4.2 AT+CREG–Register Network
    • 4.2.1 Command Syntax
    • 4.2.2 Interface Description
    • 4.2.3 Parameter Description
    • 4.2.4 Property Description
    • 4.2.5 Example
  • 4.3 AT+CLCK–Lock Facility
    • 4.3.1 Command Syntax
    • 4.3.2 Interface Description
    • 4.3.3 Parameter Description
    • 4.3.4 Property Description
    • 4.3.5 Example
  • 4.4 AT+CPWD–Change Password
    • 4.4.1 Command Syntax
    • 4.4.2 Interface Description
    • 4.4.3 Parameter Description
    • 4.4.4 Property Description
    • 4.4.5 Example
  • 4.5 AT+CUSD–USSD Command
    • 4.5.1 Command Syntax
    • 4.5.2 Interface Description
    • 4.5.3 Parameter Description
    • 4.5.4 Property Description
    • 4.5.5 Example
  • 4.6 +CUSD–Unsolicitedly Present USSD of Network
    • 4.6.1 Command Syntax
    • 4.6.2 Interface Description
    • 4.6.3 Parameter Description
    • 4.6.4 Property Description
    • 4.6.5 Example
• 5 Mobile Termination Control and Status Commands
  • 5.1 AT+CFUN–Set Operation Mode
    • 5.1.1 Command Syntax
    • 5.1.2 Interface Description
    • 5.1.3 Parameter Description
    • 5.1.4 Property Description
    • 5.1.5 Example
  • 5.2 AT+CPIN–Enter PIN
    • 5.2.1 Command Syntax
    • 5.2.2 Interface Description
    • 5.2.3 Parameter Description
    • 5.2.4 Property Description
    • 5.2.5 Example
  • 5.3 AT+CPBS–Select Phonebook Memory Storage
    • 5.3.1 Command Syntax
    • 5.3.2 Interface Description
    • 5.3.3 Parameter Description
    • 5.3.4 Property Description
    • 5.3.5 Example
  • 5.4 AT+CPBR–Read Phonebook Entries
    • 5.4.1 Command Syntax
    • 5.4.2 Interface Description
    • 5.4.3 Parameter Description
    • 5.4.4 Property Description
    • 5.4.5 Example
  • 5.5 AT+CPBW–Write Phonebook Entry
    • 5.5.1 Command Syntax
    • 5.5.2 Interface Description
    • 5.5.3 Parameter Description
    • 5.5.4 Property Description
    • 5.5.5 Example
  • 5.6 AT+CRSM–Restrict SIM Access
    • 5.6.1 Command Syntax
    • 5.6.2 Interface Description
    • 5.6.3 Parameter Description
    • 5.6.4 Property Description
    • 5.6.5 Example
  • 5.7 AT+CSQ–Query the Signal Quality
    • 5.7.1 Command Syntax
    • 5.7.2 Interface Description
    • 5.7.3 Parameter Description
    • 5.7.4 Property Description
    • 5.7.5 Example
• 6 Mobile Termination Errors
  • 6.1 AT+CMEE–Report Mobile Termination Error
    • 6.1.1 Command Syntax
    • 6.1.2 Interface Description
    • 6.1.3 Parameter Description
    • 6.1.4 Property Description
    • 6.1.5 Example
• 7 Commands for UMTS Packet Domain
  • 7.1 AT+CGDCONT–Define PDP Context
    • 7.1.1 Command Syntax
    • 7.1.2 Interface Description
    • 7.1.3 Parameter Description
    • 7.1.4 Property Description
    • 7.1.5 Example
  • 7.2 AT+CGACT–Activate or Deactivate PDP Context
    • 7.2.1 Command Syntax
    • 7.2.2 Interface Description
    • 7.2.3 Parameter Description
    • 7.2.4 Property Description
    • 7.2.5 Example
  • 7.3 AT+CGATT–Attach or Detach PS Domain
    • 7.3.1 Command Syntax
    • 7.3.2 Interface Description
    • 7.3.3 Parameter Description
    • 7.3.4 Property Description
    • 7.3.5 Example
  • 7.4 AT+CGREG–PS Domain Registration Status
    • 7.4.1 Command Syntax
    • 7.4.2 Interface Description
    • 7.4.3 Parameter Description
    • 7.4.4 Property Description
    • 7.4.5 Example
  • 7.5 AT+CGSMS–SMS Bearer Domain
    • 7.5.1 Command Syntax
    • 7.5.2 Interface Description
    • 7.5.3 Parameter Description
    • 7.5.4 Property Description
    • 7.5.5 Example
• 8 PDU Mode Commands for SMS
  • 8.1 AT+CSMS–Select Message Service
    • 8.1.1 Command Syntax
    • 8.1.2 Interface Description
    • 8.1.3 Parameter Description
    • 8.1.4 Property Description
    • 8.1.5 Example
  • 8.2 AT+CPMS–Select Message Storage
    • 8.2.1 Command Syntax
    • 8.2.2 Interface Description
    • 8.2.3 Parameter Description
    • 8.2.4 Property Description
    • 8.2.5 Example
  • 8.3 AT+CMGF–Set Message Format
    • 8.3.1 Command Syntax
    • 8.3.2 Interface Description
    • 8.3.3 Parameter Description
    • 8.3.4 Property Description
    • 8.3.5 Example
  • 8.4 AT+CSCA–Service Center Address
    • 8.4.1 Command Syntax
    • 8.4.2 Interface Description
    • 8.4.3 Parameter Description
    • 8.4.4 Property Description
    • 8.4.5 Example
  • 8.5 AT+CNMI–Indicate New Message to TE
    • 8.5.1 Command Syntax
    • 8.5.2 Interface Description
    • 8.5.3 Parameter Description
      • Table 8-1 Parameters of <bm>
    • 8.5.4 Property Description
    • 8.5.5 Example
      • 1. AT+CNMI=1,1,0,1,0
      • 2. AT+CNMI=1,1,0,2,0
      • 3. Other commonly-used settings include:
  • 8.6 AT+CMGD–Delete Message
    • 8.6.1 Command Syntax
    • 8.6.2 Interface Description
    • 8.6.3 Parameter Description
    • 8.6.4 Property Description
    • 8.6.5 Example
  • 8.7 AT+CMGL–List Messages
    • 8.7.1 Command Syntax
    • 8.7.2 Interface Description
    • 8.7.3 Parameter Description
    • 8.7.4 Property Description
    • 8.7.5 Example
  • 8.8 AT+CMGR–Read Message
    • 8.8.1 Command Syntax
    • 8.8.2 Interface Description
    • 8.8.3 Parameter Description
    • 8.8.4 Property Description
    • 8.8.5 Example
  • 8.9 AT+CMGS–Send Short Message
    • 8.9.1 Command Syntax
    • 8.9.2 Interface Description
    • 8.9.3 Parameter Description
    • 8.9.4 Property Description
    • 8.9.5 Example
  • 8.10 AT+CNMA–New Message Acknowledgement
    • 8.10.1 Command Syntax
    • 8.10.2 Interface Description
    • 8.10.3 Parameter Description
      • Figure 8-1 User data encoded using the default 7-bit encoding scheme
      • Figure 8-2 User data encoded using the 8-bit or UCS2 encoding scheme
    • 8.10.4 Property Description
    • 8.10.5 Example
  • 8.11 +CMTI–Unsolicitedly Present of Message Arrival Indication
    • 8.11.1 Command Syntax
    • 8.11.2 Interface Description
    • 8.11.3 Parameter Description
    • 8.11.4 Property Description
    • 8.11.5 Example
  • 8.12 +CMT–Unsolicitedly Present of New Message Reported Directly
    • 8.12.1 Command Syntax
    • 8.12.2 Interface Description
    • 8.12.3 Parameter Description
    • 8.12.4 Property Description
    • 8.12.5 Example
  • 8.13 +CDSI–Unsolicitedly Present of Newly Received Message Status Report
    • 8.13.1 Command Syntax
    • 8.13.2 Interface Description
    • 8.13.3 Parameter Description
    • 8.13.4 Property Description
    • 8.13.5 Example
  • 8.14 +CDS–Unsolicitedly Present of New Message Status Report Reported Directly
    • 8.14.1 Command Syntax
    • 8.14.2 Interface Description
    • 8.14.3 Parameter Description
    • 8.14.4 Property Description
    • 8.14.5 Example
  • 8.15 +CBMI–Unsolicitedly Present of Newly Received Cell Broadcast Message
    • 8.15.1 Command Syntax
    • 8.15.2 Interface Description
    • 8.15.3 Parameter Description
    • 8.15.4 Property Description
    • 8.15.5 Example
  • 8.16 +CBM–Unsolicitedly Present of New Cell Broadcast Message Directly
    • 8.16.1 Command Syntax
    • 8.16.2 Interface Description
    • 8.16.3 Parameter Description
    • 8.16.4 Property Description
    • 8.16.5 Example
• 9 Commands for Standard STK Interface
  • 9.1 +CUSATP–Unsolicitedly Present of a UICC Proactive Command
    • 9.1.1 Command Syntax
    • 9.1.2 Interface Description
    • 9.1.3 Parameter Description
    • 9.1.4 Property Description
    • 9.1.5 Example
  • 9.2 AT+CUSATE–Send USAT Envelope
    • 9.2.1 Command Syntax
    • 9.2.2 Interface Description
    • 9.2.3 Parameter Description
    • 9.2.4 Property Description
    • 9.2.5 Example
  • 9.3 AT+CUSATT–Send USAT Terminal Response
    • 9.3.1 Command Syntax
    • 9.3.2 Interface Description
    • 9.3.3 Parameter Description
    • 9.3.4 Property Description
    • 9.3.5 Example
  • 9.4 +CUSATEND–Unsolicitedly Present of Terminating a UICC Proactive Command Session
    • 9.4.1 Command Syntax
    • 9.4.2 Interface Description
    • 9.4.3 Parameter Description
    • 9.4.4 Property Description
    • 9.4.5 Example
• 10 Huawei Proprietary Interface: Mobile Termination Control and Status Interface
  • 10.1 AT^RFSWITCH–Set the Flight Mode
    • 10.1.1 Command Syntax
    • 10.1.2 Interface Description
    • 10.1.3 Parameter Description
    • 10.1.4 Property Description
    • 10.1.5 Example
  • 10.2 AT^CURC–Set Presentation of Unsolicited Results
    • 10.2.1 Command Syntax
    • 10.2.2 Interface Description
    • 10.2.3 Parameter Description
      • Table 10-1 List for the presentation of unsolicited results when CURU=0/1
      • Table 10-2 The control mode when <mode>=2
      • Table 10-3 Situation when MT does not support Wwan port
      • Table 10-4 Situation when MT supports Wwan port
      • Table 10-5 Definitions of Page 0 Bit [60~0] for the presentation of unsolicited results
    • 10.2.4 Property Description
    • 10.2.5 Example
  • 10.3 AT^HGMR–Request Version Information
    • 10.3.1 Command Syntax
    • 10.3.2 Interface Description
    • 10.3.3 Parameter Description
    • 10.3.4 Property Description
    • 10.3.5 Example
  • 10.4 AT^HWCUST–Enable Custom Hardware Function
    • 10.4.1 Command Syntax
    • 10.4.2 Interface Description
    • 10.4.3 Parameter Description
    • 10.4.4 Property Description
    • 10.4.5 Example
• 11 Huawei Proprietary Interface: Network Service Interfaces
  • 11.1 AT^SYSINFO–Query System Information
    • 11.1.1 Command Syntax
    • 11.1.2 Interface Description
    • 11.1.3 Parameter Description
    • 11.1.4 Property Description
    • 11.1.5 Example
  • 11.2 AT^SYSCFG–Configure System
    • 11.2.1 Command Syntax
    • 11.2.2 Interface Description
    • 11.2.3 Parameter Description
    • 11.2.4 Property Description
    • 11.2.5 Example
  • 11.3 AT^CSNR–Query RSCP and ECIO
    • 11.3.1 Command Syntax
    • 11.3.2 Interface Description
    • 11.3.3 Parameter Description
    • 11.3.4 Property Description
    • 11.3.5 Example
  • 11.4 AT^USSDMODE–Set USSD Mode
    • 11.4.1 Command Syntax
    • 11.4.2 Interface Description
    • 11.4.3 Parameter Description
    • 11.4.4 Property Description
    • 11.4.5 Example
  • 11.5 ^SRVST–Service State Change Indication
    • 11.5.1 Command Syntax
    • 11.5.2 Interface Description
    • 11.5.3 Parameter Description
    • 11.5.4 Property Description
    • 11.5.5 Example
  • 11.6 ^SIMST–SIM Card State Change Indication
    • 11.6.1 Command Syntax
    • 11.6.2 Interface Description
    • 11.6.3 Parameter Description
    • 11.6.4 Property Description
    • 11.6.5 Example
• 12 Huawei Proprietary Interface: STK Interface
  • 12.1 AT^CUSATM–Query the Main Menu
    • 12.1.1 Command Syntax
    • 12.1.2 Interface Description
    • 12.1.3 Parameter Description
    • 12.1.4 Property Description
    • 12.1.5 Example
• 13 Huawei Proprietary Interface: M.2 Interface
  • 13.1 AT+XTSM–Set Thermal Sensor with the Threshold
    • 13.1.1 Command Syntax
    • 13.1.2 Interface Description
    • 13.1.3 Parameter Description
    • 13.1.4 Property Description
    • 13.1.5 Example
  • 13.2 +XTS–Unsolicitedly Present of the Threshold Reached
    • 13.2.1 Command Syntax
    • 13.2.2 Interface Description
    • 13.2.3 Parameter Description
    • 13.2.4 Property Description
    • 13.2.5 Example
  • 13.3 AT+XTAMR–Query the Current Temperature of a Thermal Sensor
    • 13.3.1 Command Syntax
    • 13.3.2 Interface Description
    • 13.3.3 Parameter Description
    • 13.3.4 Property Description
    • 13.3.5 Example
  • 13.4 AT+XADPCLKFREQINFO–Query Adaptive Clock Frequency Info
    • 13.4.1 Command Syntax
    • 13.4.2 Interface Description
    • 13.4.3 Parameter Description
    • 13.4.4 Property Description
    • 13.4.5 Example
  • 13.5 +XADPCLKFREQINFO–Unsolicitedly Present of Adaptive Clock Frequency Info
    • 13.5.1 Command Syntax
    • 13.5.2 Interface Description
    • 13.5.3 Parameter Description
    • 13.5.4 Property Description
    • 13.5.5 Example
• 14 Huawei Proprietary Interface: BodySAR Interface
  • 14.1 AT^BODYSARON–Disable or Enable BodySAR
    • 14.1.1 Command Syntax
    • 14.1.2 Interface Description
    • 14.1.3 Parameter Description
    • 14.1.4 Property Description
    • 14.1.5 Example
  • 14.2 AT^BODYSARWCDMA–Set the Max Tx Power Limit of WCDMA
    • 14.2.1 Command Syntax
    • 14.2.2 Interface Description
    • 14.2.3 Parameter Description
    • 14.2.4 Property Description
    • 14.2.5 Example
  • 14.3 AT^BODYSARGSM–Set the Maximum Tx Power Limit of GSM
    • 14.3.1 Command Syntax
    • 14.3.2 Interface Description
    • 14.3.3 Parameter Description
    • 14.3.4 Property Description
    • 14.3.5 Example
• 15 Huawei Proprietary Interface: IPv6 Interface
  • 15.1 AT^IPV6CAP–Query IPv6 Capability
    • 15.1.1 Command Syntax
    • 15.1.2 Interface Description
    • 15.1.3 Parameter Description
    • 15.1.4 Property Description
    • 15.1.5 Example
• 16 Huawei Proprietary Interface: Tunable Antenna Interface
  • 16.1 AT^ANTENCFG–Set Tunable Antenna
    • 16.1.1 Command Syntax
    • 16.1.2 Interface Description
    • 16.1.3 Parameter Description
      • Table 16-1 The value of <band> when <mode>=0
      • Table 16-2 The value of <band> when <mode>=1
    • 16.1.4 Property Description
    • 16.1.5 Example
• 17 Huawei Proprietary Interface: Main And AUX Switch Interface
  • 17.1 AT^ANTMODE–Set Operation Mode of Main and AUX Antennas
    • 17.1.1 Command Syntax
    • 17.1.2 Interface Description
    • 17.1.3 Parameter Description
    • 17.1.4 Property Description
    • 17.1.5 Example
• 18 Huawei Proprietary Interface: GPS Service Interfaces
  • 18.1 AT^WPDOM–Set Operation Mode
    • 18.1.1 Command Syntax
    • 18.1.2 Interface Description
    • 18.1.3 Parameter Description
    • 18.1.4 Property Description
    • 18.1.5 Example
  • 18.2 AT^WPDST–Set Session Type
    • 18.2.1 Command Syntax
    • 18.2.2 Interface Description
    • 18.2.3 Parameter Description
    • 18.2.4 Property Description
    • 18.2.5 Example
  • 18.3 AT^WPDFR–Set Positioning Frequency
    • 18.3.1 Command Syntax
    • 18.3.2 Interface Description
    • 18.3.3 Parameter Description
    • 18.3.4 Property Description
    • 18.3.5 Example
  • 18.4 AT^WPURL–Set AGPS Server Address and Port
    • 18.4.1 Command Syntax
    • 18.4.2 Interface Description
    • 18.4.3 Parameter Description
    • 18.4.4 Property Description
    • 18.4.5 Example
  • 18.5 AT^WPDIM–Delete Auxiliary Data
    • 18.5.1 Command Syntax
    • 18.5.2 Interface Description
    • 18.5.3 Parameter Description
    • 18.5.4 Property Description
    • 18.5.5 Example
  • 18.6 AT^WPDGP–Start Positioning Session
    • 18.6.1 Command Syntax
    • 18.6.2 Interface Description
    • 18.6.3 Parameter Description
    • 18.6.4 Property Description
    • 18.6.5 Example
  • 18.7 AT^WPEND–Terminate Positioning Process
    • 18.7.1 Command Syntax
    • 18.7.2 Interface Description
    • 18.7.3 Parameter Description
    • 18.7.4 Property Description
    • 18.7.5 Example
• 19 Appendix
  • 19.1 List of URC Commands
  • 19.2 General CME Error List
    • Table 19-1 General "CME ERROR" Codes
    • Table 19-2 General "CME ERROR" Codes (Huawei proprietary)
    • Table 19-3 GPS related "CME ERROR" Codes (Huawei proprietary)
  • 19.3 CMS Error List
  • 19.4 Final Result Code
  • 19.5 References
  • 19.6 Acronyms and Abbreviations