Huawei Ets1201 Owner S Manual Phone And Accessories

2014-07-05

: Huawei Huawei-Ets1201-Owner-S-Manual huawei-ets1201-owner-s-manual huawei pdf

Open the PDF directly: View PDF PDF.
Page Count: 26

Wonderful Communication, Mobile Life.
Welcome to use HUAWEI ETS1000 Series Fixed Wireless Terminal
HUAWEI ETS1000 Series Fixed Wireless Terminal
User Guide
Copyright © 2008 Huawei Technologies Co., Ltd.
All Rights Reserved
No part of this manual may be reproduced or transmitted in any form or by any
means without prior written consent of Huawei Technologies Co., Ltd.
Trademarks
and HUAWEI are trademarks of Huawei Technologies Co., Ltd.All other
trademarks mentioned in this manual are the property of their respective holders.
Notice
The information in this manual is subject to change without notice. Every effort
has been made in the preparation of this manual to ensure accuracy of the contents,
but all statements, information, and recommendations in this manual do not
constitute the warranty of any kind, expressed or implied.
i
Contents
1 Warnings and Precautions .....................................................................................................1
2 Introduction ...........................................................................................................................5
Packing List ...................................................................................................................5
Front View .....................................................................................................................5
Rear View ......................................................................................................................7
3 Installation.............................................................................................................................8
Connecting the Terminal ...............................................................................................8
Mounting the Terminal ................................................................................................13
4 General Functions ...............................................................................................................15
Booting the FWT .........................................................................................................15
Making Calls................................................................................................................15
Answering Calls ..........................................................................................................16
Adjusting the Voice Volume ........................................................................................16
5 Advanced Functions............................................................................................................18
Supplementary Services ..............................................................................................18
Internet Services ..........................................................................................................18
Facsimile Function and Usages...................................................................................18
6 Troubleshooting...................................................................................................................20
7 Description of ETS1000 Series FWT .................................................................................22
1
1
Before using the HUAWEI Fixed Wireless Terminal (hereinafter referred to as the FWT),
tions and let your children know these, so that you can use your FWT
Warnings and Precautions
read the following cau
correctly and safely.
Basic Cautions
y According to the packing list, check items in the package box to make sure that they are
complete and undamaged.
y Before installing and using the FWT, read this user guide carefully.
Electronic Device
Power off your FWT near high-precision electronic devices. The FWT may affect the
performance of these devices.
Such devices include hearing aids, pacemakers, fire alarm systems, automatic gates, and
other automatic-control devices. If you are using an electronic medical device, consult the
facturer and confirm whether the radio waves affect the operation of the
device manu
electronic device.
Hospital
Pay attention to the following points in hospitals or health care facilities:
U), or
coronary care unit (CCU).
WT near medial devices.
y Do not take your FWT into the operating room (OR), intensive care unit (IC
y Power off your F
y Observe any instructions wherever the use of wireless device is prohibited.
Traffic Safety
Do not use your FWTy while driving. Secure the FWT on its holder. Do not place the
FWT on the seat or other places where it can get loose in a sudden stop or collision.
ons of airline companies. Power off your FWT before
y Observe the rules and regulati
boarding an aircraft.
2
Operating Environment
Do not place magnetic storage media such as magnetic cards and floppy disks near the y
,
n it
y
t
y
not
y
y
al
y re and security design
any consequence resulted from the operation without permission.
ed to conform to the authoritative international radio frequency (RF)
FWT. Radiation from the FWT may erase the information stored on them.
y Do not put your FWT, battery, or other accessories in containers with strong magnetic
field, such as the induction cooker and microwave oven. Otherwise, circuit failure, fire
or explosion may result.
y Do not place or use the FWT, the battery or the power adapter near any heat sources such
as fire or a heater; or places with flammable gases; or areas with electrical appliances
that give out heat. Otherwise, it will cause fire, explosion and breakdown of the FWT
y Because the FWT needs to eliminate heat during working, put the FWT and the power
supply in a ventilated and shadowy place. Never airproof the FWT or put something o
or place it near water, fire as well as inflammable and explosive materials.
Because the FWT contains precision devices, you should put it in a dry place and away
from moist materials.
y Before cleaning the FWT, please power off the FWT, and then disconnect the power
supply and take out the battery. Before moving the FWT, please disconnect the external
power supply.
y Do not subject your FWT, battery, and power adapter to serious collision or shock.
Otherwise, battery leakage, FWT malfunction, overheats, fire, or explosion may result.
y Do not place sharp metal objects such as pins near the earpiece. The earpiece may attrac
these objects and hurt you when you are using the FWT.
Do not place the FWT in the area over the air bag or in the air bag deployment area.
Otherwise, the FWT may hurt you owing to the strong force when the air bag inflates.
y In raining and lightning, disconnect the power adapter from external power supply and
power off the FWT, In this case, if the outdoor antenna is used, do not touch the FWT
and antenna.
y Put your FWT, battery, and power adapter in places beyond the reach of children. Do
allow children to use the FWT, battery, or power adapter without guidance.
Do not touch the antenna when a call is going on. Touching the antenna may affect call
quality and cause the FWT to operate at a power level higher than needed.
The network signal condition will directly affect the quality and stability of the call.
Consequently, you should place the FWT in a place where it can receive network sign
well. Do not put FWT in a building with an iron or metal roof. The distance between
FWT and other metal materials (such as metal brackets or metal doors and windows)
should be greater than 25cm and the distance between FWTs should be greater than
30cm.
y Do not open the chassis in any case and the device should be maintained by a qualified
maintenance department.
Without permission, you are not allowed to modify the architectu
of FWT. You must bear
y Your FWT is design
specifications. Use FWT accessories approved by Huawei only.
3
Emergency Call
nnot
be solely on the FWT for essential communications.
You can use your FWT for emergency calls. However, connections in all conditions ca
guaranteed. You should never rely
B
avoid
y a
the FWT
awei Technologies Co., Ltd is not responsible for any consequences
n-standard batteries or power supplies. Dispose of used batteries
y ws or regulations.
attery
y If the battery fluid gets into eyes, do not rub them. Wash with clean water and seek
medical assistance immediately.
y If the battery fluid contacts skin or cloth, wash with clean water immediately to
irritation to the skin.
y Do not dispose of the battery in fire. Otherwise, the battery may ignite or explode.
y When installing the battery on your FWT, do not push the battery by force lest battery
fluid leak out or the battery crack.
y Do not connect two poles of the battery with metallic materials such as cables.
y Do not disassemble the battery or solder the battery poles. Otherwise, fluid leakage,
overheat, fire, or explosion may result.
y If there is battery leakage, smoke, or strange smell, stop using the battery and keep it
away from open flame to avoid fire or explosion.
Disconnect the power adapter and take out the battery when the FWT is not used for
long time.
y Do select its self-contained complete battery and power adapter; otherwise,
may be spoiled. Hu
caused by using no
according to the instructions.
Dispose of the battery according to local la
P
lt in
re
circuiting of the battery or power adapter may result.
er adapter is properly inserted into the power socket when
insertion may result in electric shock, fire, or explosion.
ower Adapter
y Use AC power as specified for the power adapter. Any violation of this rule may resu
fire or malfunction of the power adapter.
y Do not short-circuit the power adapter. Short-circuiting the power adapter may cause fi
or malfunction of the power adapter.
y Remove the dust on the power plug regularly.
y Do not use worn-out power cords. Otherwise, electric shock, short-circuiting of the
power adapter, or fire may result.
y Do not put the power adapter near the container filled with liquid such as water. If the
liquid comes into the power adapter, electrical leakage or other faults may result.
y If the liquid such as water comes into the power adapter accidentally, remove the plug of
the power adapter from the socket immediately.
y Disconnect the power adapter from the socket before cleaning or maintaining it.
Otherwise, electric shock or short-
y Ensure the plug of the pow
charging the battery. Improper
y Do not place any heavy object on the power cord of the power adapter. Do not damage,
change, or pluck the power cord.
4
Using the USB Cable
To use the USB cable, you need operate abiding strictly by the following rules. Otherwis
your FWT or PC may be damaged:
e,
y In the process of communication between your FWT and PC, it is strictly forbidden to
y To connect your FWT and PC with the USB cable, connect to the FWT at first, and then
connect to the PC.
plug or pull out the USB cable.
y To disconnect your FWT and PC from the USB cable, disconnect from the PC at first,
and then disconnect from the FWT.
Environmental Protection
Abide by the local laws in disposing of the package materials of your FWT, consumed
batteries and used FWT, and try to recycle them.
5
2 Introduction
Packing List
Check the delivered items against the packing list shown in the table below, and make sure
that all the e in good co e is any s or damage, please contact
the local agent.
items ar nditions. If ther hortage
Item Qua ty nti Item Qua ty nti
FWT host 1 Certificate of Quality 1
Power adapter 1 Battery (Rechargeable) 1
Phone cable 1 User Manual 1
Note
information, please consult your local sales agent.
nt to use the FWT for accessing the Internet, you also need to purchase
ed data suite. For more information, please consult your local agent.
Front View
:
y The FWT should be configured with an antenna. Please select either an indoor
or an outdoor antenna depending on the local radio signal strength. For more
y If you wa
the requir
The following figure illustrates the front view of the FWT host:
9
8
7
1
23
4
6
5
6
The ports on the host are described as follows:
NO. Item Description
1 FWT switch The switch is used to switch on or switch off the FWT.
2 DC input This port is used to connect the FWT with the power
adapter.
3 Telephone port 1 This port is used to connect the device with an external
telephone to provide voice services.
4 Telephone port 2 This port provides the same functions as telephone port 1
and can connect a telephone in parallel with telephone
port 1.
5 Serial port This port is used to connect with a PC to perform data
services and is mainly used for maintaining the FWT.
6 Antenna port This port can be directly connected with an indoor
antenna. Also, it can be connected to an outdoor antenna
through a feeder cable.
The LEDs on the host are described as follows:
NO. Item Description
7 Power LED The LED in green indicates the power adapter is
connecting with the FWT.
8 Battery LED When the battery serves as the only power supply
(without external power adapter):
y The LED in green indicates the battery is in full
electricity.
y The LED in orange indicates the battery is in medium
electricity.
y The LED in orange with blinking indicates the battery
is in low electricity and needs to be recharged.
When using an external power adapter (with battery
installed):
y The LED in orange indicates the battery is recharging.
y The LED in green indicates the battery is fully
charged.
9 Signal strength
LED
Four LEDs indicate the signal strength. The more the
LEDs are on, stronger the signal is.
7
Rear View
The following figure illustrates the rear view of the FWT host:
1
2
3
4
5
The ports are described as follows:
NO. Item Description
1 Wall-mounting
brackets
The wall-mounting brackets are used to mount the
terminal host on the wall.
2 R-UIM card slot The R-UIM card slot is used to install the
Removable-User Identity Module (R-UIM) card.
3 Battery port This port is used for the connection with the battery.
4 Battery The terminal is configured with a battery for backup
when the external power adapter fails.
5 Battery cover To maintain the battery, you need to remove its cover
first.
8
3
erminal
Installation
Connecting the T
Installing the Battery
om injuring human body, please note:
u use the outdoor antenna, disconnect it before disassembling the FWT and
No
y ure allowed for charging,
y ower adapter is in use, the FWT will automatically charge the
y
s.
ve
Caution:
To prevent lightning fr
If yo
installing the battery.
te:
When the ambient temperature exceeds the temperat
the system will enter the protection status and stop charging the battery.
When the p
battery and stop it after the battery is fully charged.
If the FWT is left unused for a long period, you need to take the battery out of
the FWT.
y Before using the battery for the first time, charge the battery for at least 8 hour
When the battery is fully charged but not used for a long time, charge it for fi
minutes before using it again.
Make sure that the power adapter has been powered off and disconnected from the
terminal. Open the cover of the ba
1.
ttery as shown in the above figure.
e battery into the battery
port on the terminal (please make sure the insert direction), and then seat the battery in
the battery container in the host.
3. Close the battery cover to complete the battery installation.
2. When installing the battery, insert the connection cable of th
9
Installing the R-UIM Card (Optional)
Note:
y Consult the sales agent or the carrier to decide whether to install the R-UIM
card or not.
y Switch off the FWT, disconnect the FWT from power adapter and remove the
battery before installing R-UIM card.
y R-UIM card and the contact point are easily to be damaged for scar or
overbending, so you should insert or remove it gently.
1. Open the battery cover and remove the battery.
2. Insert R-UIM card to the card slot as the arrow shows in the above figure. Put the side
with a corner cutting backwards and the side with a golden contact downwards, and
then make sure the R-UIM card is completely inserted into the slot.
3. Reinstall the battery and install the battery cover.
Installing the Indoor Antenna
In an area that signals can be transmitted and received with good quality, you can install an
indoor antenna, as shown in the following figure.
1. Make sure that the FWT is switched off.
2. Align the indoor antenna with the antenna port on the FWT host in the direction shown
in the above figure, and then screw the antenna, ensure that the connection is secure.
10
Installing External Power Adapter
In normal conditions, the FWT depends on an external power adapter for power supply and
will use the battery only in the case that the electricity has failed and the external power
adapter is unavailable. As the battery can supply power only for a limited period, you must
make sure that the battery has been fully charged before putting it into use.
1. Make sure that the FWT is switched off.
2. Insert one end of the power adapter into the DC input port as shown in the figure, and
the other end into the power supply jack.
3. Turn on the FWT switch of the terminal and wait for a few seconds. If the power LED
is green, the connection is correct.
Connecting the FWT to a Telephone
The FWT can provide voice services only when it is connected to a telephone. The
following figure shows the connection.
11
Connect the telephone to a telephone port on the FWT through a cable with an RJ11
connector. The FWT provides two telephone ports respectively numbered 1 and 2. You can
use either of them, because they are internally interconnected.
You can use the telephone cable delivered with the FWT to connect the FWT and a
telephone, and you can also connect the telephone port to other telephone set (the two
telephones are in parallel connection and use the same number).
Connecting the FWT to a PC
The FWT can be connected to a PC to provide data services, maintain the terminal and
debug the terminal. You need to purchase the data service suite. For more information,
please consult your local agent.
Caution:
y To avoid damaging the device when making connection, switch off the FWT
and use the data cable provided by the manufacturer.
y The FWT can be connected to a telephone and a PC at the same time, but the
voice and data services cannot be used simultaneously. That is, you can use only
one service at a time.
Connect one end of the data cable to the PC and the other end to the FWT. Fasten the
captive screw to ensure the reliable connection.
12
Connecting the FWT to a Facsimile Set
Connect the FWT to facsimile set to perform facsimile function.
Note:
Please affirm that your FWT supports facsimile before using this function. For
detailed model description, please refer to the “Description of ETS1000 Series
FWT”.
Connect the FWT and the facsimile set with a telephone line delivered in the accessories.
Connect the facsimile set to a telephone port on the FWT through a cable with an RJ11
connector. The FWT provides two telephone ports respectively numbered 1 and 2. You can
use either of them, because they are internally interconnected.
Viewing the Receiving Signal Strength
The FWT provides you with the function of measuring the receiving signal strength,
specifically as follows.
Searching for signals
Power on the FWT, and wait for a while until some signal intensity LEDs become on or
until you can hear the dial tone upon the off-hook action.
1. If all the signal intensity LEDs keep off five minutes later and only the reorder tone can
be heard, no signals can be received. In this case, you should re-position the antenna.
2. If all the signal intensity LEDs still keep off after the antenna has been turned for all
position, it means that the signal quality is very poor at this area.
3. If the dial tone can be heard in some area, you should position the antenna towards this
direction.
Viewing the receiving signal strength
By viewing the receiving signal intensity LEDs on the FWT host panel, you can know the
present receiving signal strength. There are four LEDs to indicate the receive field intensity
levels. The table below describes the signal intensity that each number of light LEDs
indicates.
13
The number of light LEDs Signal intensity level Signal strength
0 0 Extremely poor
1 1 Poor
2 2 OK
3 3 Good
4 4 Strong
Normally, the FWT requires the receiving signal strength to reach level 2 and above. When
installing the antenna, you should try to choose a good position and direction to achieve the
good receiving signal strength.
Note:
The signal strength reaching level n means that the LEDs representing level n or
above keep on more than 80 percent of the time when the terminal is in operation.
Mounting the Terminal
Horizontal Mounting
To prevent the terminal from falling and hence being damaged, you should put it on a
smooth surface at a cool place with good ventilation. The terminal should be placed at least
10cm away from any other objects around.
Vertical Mounting
The terminal can be vertically mounted on a wall.
Before mounting the terminal, make the marks on the wall according to the measurement
shown in the figure, fix two wall screws into the wall in place with the screw heads
extending approximately 3 mm from the surface of the wall, align the mounting brackets at
14
the terminal bottom with the screws, push the host towards wall, and mate the brackets with
the screws, ensuring that the host is stable enough. Then you can hang your terminal on the
wall.
15
4 General Functions
Booting the FWT
The boot process of the FWT will last about 20 seconds after it is switched on. If the
l is strong, the signal strength LEDs will light after the booting process is
er off hook and dial tone sounds, you can make or answer a call, or send or
receive a
Note
y twork signal is too weak, all signal strength LEDs may be off after the
trong network
y fter the adjustment, the
weak network signal is irrelevant to the position of the antenna.
emain off, the FWT may fault or the network is not covered the
ase, consult the sales agent or the carrier.
network signa
complete. Aft
fax.
:
If the ne
FWT is switched on. In this case, it is recommended that you adjust the position
of the antenna until you can observe the indication of relatively s
signal.
If the signal strength LEDs remain in an ON-OFF state a
y If the LEDs r
area. In this c
Making Calls
Before off-hook, make sure that at
strength LEDs are off, the signal s
least one signal strength LED is on. If all the signal
trength is extremely weak and you have little chance to
Method 1: Dial a telephone number in a regular way, and the number will be dialed out in
seven seconds. For example, if you want to dial the telephone number “4503421”, simply
dial all the digits of the number.
make a call successfully.
Follow these steps to make a call:
1. Hook off and dial upon hearing the dial tone.
2. Dial the number in either of the following ways.
16
Note:
y You can set the wait time for of the FWT by entering “##58*n#”, where n
ranges from 0 to 9. Setting n to 0 will disable the auto-dial-out function of the
FWT. Otherwise, the FWT will automatically dial out your desired number in n
seconds.
y By default, n is 7 seconds.
y To validate this function, you must reboot the FWT.
Method 2: Dial all the digits of the number plus one “#”. In this way, the FWT will
immediately dial the number. For example, if you want to dial the telephone number
“4503421”, you can dial all the digits of the number plus “#” (4503421#).
Note:
y The dial interval between two consecutive numerals cannot not exceed the wait
time for auto-dial-out of the FWT. Otherwise, the phone number will be
automatically dialed out.
y When you use some supplementary services, you may dial the numbers started
with “*” or “#”, such as “#36*”. In these cases, you can dial the number by
using method 1 with the wait time for auto-dial-out as non-0.
3. Wait for several seconds after dialing. When the ring-back tone is heard, the connection
is set up. If the busy tone is heard, the attempt of setting up the connection fails
because of a busy line or other reasons. In this case, hook on, wait for a while, and
hook off to redial.
4. Enter the session state.
5. Hook on to terminate the session.
Answering Calls
Make sure to hook on the telephone in place when you do not make calls, so that you can
receive calls.
1. The telephone rings. If both the telephone and the network support the Calling Line
Identification Presentation (CLIP), the telephone will display the calling number upon
the second ring tone (for more information, consult the carrier). If you pick up the
telephone before hearing the second ring tone, you cannot see the calling number.
2. Hook off to set up the session.
3. Hook on to terminate the session.
Adjusting the Voice Volume
You can adjust the voice volume when the telephone is either in standby state or in session
state. Four volume levels (1 to 4) are available, with level 1 being the lowest and level 4 the
highest.
Follow these steps to adjust the voice volume.
17
Adjusting the Volume When the Telephone Is in Standby State
1. Hook off and you can hear the dial tone, which means that the telephone service is
available now.
2. Press “##1” to adjust the volume.
3. To get the desired volume, press the key 1 through 4 that respectively represents the
volume levels 1 through 4.
4. After selecting the desired volume, press the “*” key to save it. If you hear the
confirmation tone of a “toot”, you have successfully set the volume level.
5. You can hear the dial tone again, which means that the FWT has returned to the
off-hook state, and you can proceed to make a call or perform other settings.
Note:
If you hear the reject tone of “toot, toot” when setting the volume, you have
pressed an incorrect key and this setting attempt fails. The system will return to the
off-hook state, and you can retry to make the setting after hearing the dial tone
again.
Adjusting the Voice Volume in an Ongoing Session
1. If you are in a session with the remote party, you can press ##1 to adjust the volume.
2. To obtain the desired volume, press the key 1 through 4 that respectively represent the
volume levels 1 through 4, and you can hear the voice changing during the talk.
3. After selecting the desired volume, press the “*” key to save it. If you hear the
confirmation tone of a “toot”, you have successfully set the volume level.
4. Keep in session state.
Note:
If you hear the reject tone of “toot, toot” when setting the volume, you have
pressed an incorrect key and this setting attempt fails. However, the session state
will still be kept, and you can perform operations from Step 1 to Step 4 to adjust
the volume again.
18
5 ctions Advanced Fun
Supplementary Services
The FWT supports the
n to enab
supplementary services. To use the supplementary services, you
le them. For details, consult the network carrier. Here, only several
or your reference.
g
y Call Transfer
Internet Services
eed the carrier
typical services are listed f
y Three-Way Callin
y Call Forwarding
y Emergency Call
The FWT can also help you access the Internet. For details, consult your service provider.
Facsimile Function and Usages
Connect the f
Facsimile Set
acsimile set and the FWT correctly according to “Connecting the FWT to a
” and confirm the normal operation state according to “Booting” , and then
you can
No
y function requires the network support. For details, consult the
y s rate of sending or receiving a fax is related to the performance of
y
y Here, only the brief introduction of using the facsimile set is given. The
pends on the brand and type of different facsimile sets. For
send or receive a facsimile.
te:
The facsimile
carrier.
The succes
the network.
To avoid errors, do not perform other services when sending or receiving a
facsimile.
operation also de
details, refer to the instructions of relevant facsimile sets.
19
Sending a Facsimile
1. Dia
num
“##
2. After hearing the sound of “toot”, press send button in the facsimile set to send a fax
s configured the auto-receive mode).
party
ription of the
l the fax number of the called party on the facsimile set, with “##0” before the
ber and “*” after the number. For example, if the fax number is 6540123, dial
06540123*”.
(suppose the called party i
Note:
It is suggested that the called party configure auto-receive mode. If the called
has configured manual-receive mode, refer to the corresponding desc
facsimile set.
Receiving a Facsimile
1. Dial “##36*” on the facsimile set to access “facsimile mode”.
2. A sound o
received.
f “toot” indicates that the FWT is in facsimile mode and the fax can be
3. The
y Dial “## nd of “toot”, FWT is exited from
“facsi
y Restart t
After exit f
Note
y
cannot answer a call.
y In some network conditions, the FWT supports the voice-to-facsimile function,
that is, you can perform operation through the normal mode for sending and
receiving a facsimile. For example, to send a facsimile, you can directly dial the
desired number without the need to add “##0” before the number and “*” after
the number. Moreover, to receive a facsimile, you also do not need to access
“facsimile receive mode”. Consult your carrier about whether your network
supports this function.
following two methods can be taken to exit from “facsimile mode”:
30*” on the facsimile set. After hearing the sou
mile mode”.
he FWT and it will exit from “facsimile mode”.
rom “facsimile mode”, you can use the FWT to make or answer a call normally.
:
You can make a call or send a fax after configuring the FWT to “facsimile
receive mode”, but you
20
6
ter. Switch on
n
terminal with the external power adapter.
is
, check whether the AC input is correct.
normal state, but all signal
ssary for the directional antenna).
.
connection between the telephone
ak. Use an outdoor antenna or move the FWT to a position with stronger signal.
vironmental interference. For details, consult
can adjust them by following the instruction
received.
Troubleshooting
The FWT is not connected to an external power adap
the FWT, but the battery LED is still off.
Open the battery container to check whether the battery is installed.
If the battery is installed, the problem may result from low power supply of the battery. I
this case, you need to connect the
Connect the power adapter to the FWT, switch on the FWT, but the
power LED remains off.
If the output voltage of the power adapter cannot meet the requirements of the FWT, th
problem may occur. In this case
Switch on the FWT, the power LED is in
strength LEDs are off.
Check whether the antenna is correctly installed.
If an outdoor antenna is used, place the antenna at a higher position, or adjust the antenna
direction (only nece
The signal strength LED is in normal state, but no dial tone is heard
after off hook
See “Connecting the FWT to a Telephone” to check the
set and the FWT.
The voice is unstable and discontinuous.
Check how many signal strength LEDs are on. If less than two LEDs are on, the network
signal is we
The signal intensity strength may be led by en
the carrier.
The volume is too loud or too low.
The FWT has four levels of volumes, and you
of “Adjusting the Voice Volume in an Ongoing Session”.
The facsimile cannot be
See “Receiving a Facsimile” to configure the FWT to “facsimile receive mode”.
21
g a
g the send key after hearing the
wrong fax number.
ng mode but not started receiving.
an FWT is connected with two phones at the same time, and one phone is in use, the
phone’s handfree function may not work. You can use the handset.
Answering a call fails.
You cannot answer a call if the FWT is in “facsimile receive mode”. See “Receivin
Facsimile” to exit from this mode first.
Sending a facsimile fails (pressin
sound of “toot”)
It may be caused by the following reasons:
1. The network signal is weak.
2. You have dialed a
3. The called party has configured manually receivi
4. The line is busy.
The handfree function cannot be used.
If
other
22
7
F
Description of ETS1000 Series
WT
Series Model Description
ETS1000 Series ETS1000/ and. ETS1001 can support
annot.
ETS1001
It operates in 450MHz b
G3 analog facsimile function but ETS1000 c
ETS1200 Series
ETS1201 3 analog facsimile function
but ETS1200 cannot.
ETS1200/ It operates in 800MHz frequency channel.
ETS1201 can support G
ETS1500 Series ETS1500/
ETS1501
It operates in 1900MHz frequency channel.
ETS1501 can support G3 analog facsimile function
but ETS1500 cannot.
Version: V200R003_06 Part Number: 31017718

Navigation menu