Hunetec M1503RFX ReFlex Telemetry Device User Manual M1503 service manual

Download:
Mirror Download [FCC.gov]
Document ID	1503074
Application ID	v6H7XisbLeMiG/PcgThOag==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	21.37kB (267107 bits)
Date Submitted	2011-07-18 00:00:00
Date Available	2011-07-18 00:00:00
Creation Date	2011-06-20 13:34:34
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2011-07-15 09:47:54
Document Title	Microsoft Word - M1503 service manual
Document Creator	PScript5.dll Version 5.2.2
Document Author:	hunetec

1/17
M1503 Service Manual
June 2011
HuneTec Co.,Ltd
HuneTec Confidential Proprietary
COPYRIGHT ⓒ, 2011 HuneTec CO., Ltd.
All Rights Reserved
2/17
GENERAL INFORMATION
1. Introduction
▪ Small Size and Light Weight for Portability
▪ ReFLEX Two-way Messaging
▪ Graphic User Interface for Easy Use
▪ Personal Information Management Support
▪ PC Connectivity for Data Back-up and Restoring with Desktop PC
2. RF Specification
▪ Tx Frequency Range: 896 MHz ~902MHz
▪ Rx Frequency Range: 929 MHz ~932MHz, 935 MHz ~942MHz
▪ Channel Spacing: 12.5 KHz/10KHz
▪ Frequency Deviation: 800Hz and 2400Hz
▪ Signaling Modulation: 4 level FSK
3. Physical Specification
▪ Operating temperature range: -10°C ~ +50°C (32F~122F)
▪ Dimensions
－Size: 77×53×17mm
－Weight: 65grams
▪ Power Consumption
－Batteries: Li-Polymer 800mA rechargeable battery
－Stand-by Time: 10 days
－Recharging Time: 2 hours
－Rx Consummation: 45mA
－Tx Consummation: 800mA
－Idle Current: 1.0mA
HuneTec Confidential Proprietary
COPYRIGHT ⓒ, 2011 HuneTec CO., Ltd.
All Rights Reserved
3/17
▪ Display
－Full-graphics high-contrast screen
－Resolution 160×64dots
－Lines by 24 characters
－LED back lighting
－4 gray LCD
▪ Accessories
－Belt clip
－Dock
HuneTec Confidential Proprietary
COPYRIGHT ⓒ, 2011 HuneTec CO., Ltd.
All Rights Reserved
4/17
Product Overview
M1503 are Small Size and Light Weight for Portability, microcomputer-controlled frequency
modulated transceivers. Each M1503 has a AMPIRETM Liquid Crystal Display (LCD), and is
powered by a BYDTM Li-Polymer battery. The receiver operates in the 929 MHz ~932MHz, 935
MHz ~942MHz range; the transmitter operates in the 896 MHz ~902MHz range.
1. Housing
The M1503 is housed in a high-impact plastic case which offers excellent protection against dust
intrusion, vibration, and shock. Small and light weight, the unit is designed to be clipped onto
your belt or fit comfortably in a shirt or jacket pocket.
2. Features
▪ Attractive, miniature styling
▪ High-contrast, graphic dot-matrix liquid crystal display (LCD)
▪ High-visibility backlighting
▪ Microprocessor control with advanced software algorithms
▪ Out-of-Range and low battery indicators
▪ Real-time clock with time, date and alarm
▪ Battery backed message memory with time and date stamp
▪ User-selectable alert screen with musical alert, chirp alert, standard alert, vibrate, and no alert
▪ Li-Polymer rechargeable battery
3. Optional Alert Features
The M1503 also provides the following optional alert features:
- Vibrator alert
- No alert
- Reminder alert
4. Liquid Crystal Display (LCD)
The LCD provides a full-graphics high contrast screen, resolution 160×64 dot-matrix display for
easy readability. The LCD also features a LED backlight for reading the display in low-light
conditions. The LCD is capable of displaying up to line by 24 characters by using multi
font(large/small) display.
HuneTec Confidential Proprietary
COPYRIGHT ⓒ, 2011 HuneTec CO., Ltd.
All Rights Reserved
5/17
5. General Operation
This section describes the general operation of the following areas:
System Acknowledge
The M1503 automatically acknowledges the receipt of a message by transmitting an
acknowledge transmission (ACK), indicating the receipt of the message. The M1503
also transmits a negative acknowledge (NACK) when messages are not received
correctly. If the transmits a NACK, the system resends the message.
Acknowledge Read message
M1503 is respond automatically when the user reads the message. A message is
considered read when it displays on the read screen or is moved to the personal folder.
A message is considered not read when it is merely viewed on the message preview
screen.
User Reply
User reply is an optional feature that routes back to the calling party. The reply is
selected from preprogrammed responses stored in the M1503, or multiple choice
responses originating from the calling party that are included with the message.
Signature Tracking
The messaging system uses signature tracking to link sent messages to their responses.
Signature expiration ensures that a response to an old message does not mistakenly link
to a new message with the same signature.
Registration Request
Registration allows nationwide systems to track the M1503 from region to region. The
system then transmits messages only to that region. Automatic registration is
enabled/disabled by the allow auto-registration option.
The registration request message generates on the following occasions:
▪ A valid zone change – The M1503 monitors the Zone ID field in the ReFLEX25
frame header. When the M1503 recognizes that the frame header has changed,
the PIC automatically sends a registration message after a programmable delay.
▪ Power up – Upon power up, the M1503 automatically transmits a registration
request.
HuneTec Confidential Proprietary
COPYRIGHT ⓒ, 2011 HuneTec CO., Ltd.
All Rights Reserved
6/17
▪ A change from out-of-range to in-range - When the M1503 goes out of
forward—channel range, and then returns within forward-channel range, it
automatically transmits a registration request after a programmable delay.
▪ Failed reply causes the M1503 to try and register
6. Paging Operation
M1503 can be configured to accept alphanumeric-display, numeric-display. When a message is
received, the M1503s a 2 or 12 second alert depending on M1503 programming.
HuneTec Confidential Proprietary
COPYRIGHT ⓒ, 2011 HuneTec CO., Ltd.
All Rights Reserved
7/17
Theory of Operation
The M1503ists of a Radio Frequency (RF) transceiver and a microcomputer-controlled decoder,
referred to as the controller.
Messages are received from an RF carrier that is frequency modulated by a coded binary
sequence. The circuits in the transceiver section, through a triple-conversion process, convert the
RF signal to a low frequency signal that is passed on to the controller. The controller processes
the coded data using digital techniques, and controls message memory, Liquid Crystal Display
(LCD), and alert tones.
The controller processes coded messages, and forwards the messages to the transmitter. The
transmitter section generates a modulated RF carrier signal, amplifies the signal, and then
radiates the signal through the antenna.
The following describes the general theory of operation for the M1503cuit descriptions, detailed
functional block diagrams, and schematics for the transceiver and controller are explained in the
applicable sections of this manual.
1. Operating Power
The transceiver and controller circuit board obtain power from the following sources: A 3.7 volt
rechargeable Li-Polymer battery Provides power to the 3-volt regulator and the transmitter power
amplifier.
HuneTec Confidential Proprietary
COPYRIGHT ⓒ, 2011 HuneTec CO., Ltd.
All Rights Reserved
FCC Compliance Information
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received.
Including interference that may cause undesired operation
Information to User
“NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the quipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Caution : The user who makes Changes or Modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate the equipment.
SAR INFORMATION
THIS MODEL WIRELESS PAGER MEETS THE
REQUIREMENTS FOR EXPOSURE TO RADIO WAVES.
GOVERNMENT’S
Your wireless pager is a radio transmitter and receiver. It is designed and manufactured not to exceed
the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications
Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish
permitted levels of RF energy for the general population. The guidelines are based on standards that
were developed by independent scientific organizations through periodic and thorough evaluation of
scientific studies. The standards include a substantial safety margin designed to assure the safety of
all persons, regardless of age and health.
The exposure standard for wireless pager employs a unit of measurement known as the Specific
Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. * Tests for SAR are conducted
with the wireless pager transmitting at its highest certified power level in all tested frequency bands.
Although the SAR is determined at the highest certified power level, the actual SAR level of the
wireless pager while operating can be well below the maximum value. This is because the wireless
pager is designed to operate at multiple power levels so as to use only the power required to reach
the network. In general, the closer you are to a wireless base station antenna, the lower the power
output.
Before a wireless pager model is available for sale to the public, it must be tested and certified to the
FCC that it does not exceed the limit established by the government adopted requirement for safe
exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body)
as required by the FCC for each model. The worn on the body, as described in this user guide, is
1.110mW/g. (Body-worn measurements differ among wireless pager models, depending upon
available accessories and FCC requirements). While there may be differences between the SAR
levels of wireless pager and at various positions, they all meet the government requirement for safe
exposure.
The FCC has granted an Equipment Authorization for this model wireless pager with all reported SAR
levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this
model wireless pager is on file with the FCC and can be found under the Display Grant section of
http://www.fcc.gov/oet/fccid after searching on FCC ID: RNGM1503RFX
Additional information on Specific Absorption Rates (SAR) can be found on the Cellular
Telecommunications Industry Association (CTIA) web-site at http://www.wow-com.com.
* In the United States and Canada, the SAR limit for wireless pager used by the public is 1.6 watts/kg
(W/kg) averaged over one gram of tissue. The standard incorporates a sub-stantial margin of safety to
give additional protection for the public and to account for any variations in measurements.
BODY-WORN OPERATION
This device was tested for typical body-worn operations with the back of the wireless pager kept 1.0
cm from the body. To maintain compliance with FCC RF exposure requirements, use only belt-clips,
holsters or similar accessories that maintain 1.0 cm separation distance between the user’s body and
the back of the wireless pager, including the antenna. The use of belt-clips, holsters and similar
accessories should not contain metallic components in its assembly. The use of accessories that do
not satisfy these requirements may not comply with FCC RF exposure requirements, and should be
avoided. For more information about RF exposure, please visit the FCC website at www.fcc.gov.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : hunetec
Create Date                     : 2011:06:20 13:34:34+09:00
Modify Date                     : 2011:07:15 09:47:54+09:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2011:07:15 09:47:54+09:00
Format                          : application/pdf
Title                           : Microsoft Word - M1503 service manual
Creator                         : hunetec
Document ID                     : uuid:2f5f7588-b515-4380-9176-7ff439e94397
Instance ID                     : uuid:24522aec-bf4b-402d-8145-c8cf72ce05c4
Page Count                      : 9

EXIF Metadata provided by EXIF.tools