Hunter Douglas Window Fashions PC4 Motor Control Hub User Manual Hub Guide English Rev 1

Download:
Mirror Download [FCC.gov]
Document ID	3849224
Application ID	Q0hYVY59z3mu6kZ/YCmS3A==
Document Description	Users Manual Rev 1a
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	25.22kB (315256 bits)
Date Submitted	2018-05-14 00:00:00
Date Available	2018-05-14 00:00:00
Creation Date	2018-03-19 11:09:39
Producing Software	Nitro PDF PrimoPDF
Document Lastmod	2018-03-19 11:09:39
Document Title	Hub Guide English Rev 1.pdf
Document Creator	PrimoPDF http://www.primopdf.com
Document Author:	jbaugh

PowerView Hub
®
QUICK START GUIDE
© 2017 Hunter Douglas. All rights reserved. All trademarks used herein
are the property of Hunter Douglas or their respective owners. 8/17
When prompted, scan or type the
Accessory Setup Code below.
Troubleshooting . . . . . . . . . . . . . . . 15
Home Automation Integration . . . . . . . 13
Connections . . . . . . . . . . . . . . . . . 5
Kit Contents . . . . . . . . . . . . . . . . . 3
Table of Contents
Repeater
Wireless Router
Note: Do not expose the PowerView Hub to direct sunlight.
The PowerView ® Hub interfaces with the PowerView ® App to allow
control of Hunter Douglas motorized window coverings from mobile
devices. The Hub can also integrate with home automation systems
via IP or cloud-to-cloud integration.
Power Supply
PowerView Hub
A.
USB Power Supply Cable
Cable (Optional)
C.
E. Ethernet
D.
B.
Apple is a trademark of Apple Inc., registered in the U.S. and other countries.
Android is a trademark of Google Inc.
Note: Download the PowerView® App. The App is available for Apple ® iOS and
Android™ mobile devices.
B.
PowerView ® Hub USB
PowerView ® Repeater
C. USB Power Supply
A.
D.
E.
K I T CON T EN T S
Note: During the boot-up process, the Hub’s LED may turn off and on again. Once
the Hub has completed the boot-up process, it will consistently blink AMBER. Do not
interrupt the boot-up process by cutting power or pressing any buttons on the back
panel of the Hub.
3. Plug the other end of the USB power cable into the power port
on the back of the Hub.
2. Plug the USB power supply into an AC outlet or power strip.
1. Connect one end of the USB power cable to the USB power
supply.
Connect power to Hub.
Note: If connecting the Hub to the home network via Ethernet, connect the
Hub to the router, before connecting the Hub to power.
Connect the Ethernet cable from the Hub to an open LAN port on your router.
The Hub will continue to blink AMBER, once it has been connected to the
home network.
Connect using an Ethernet cable (optional)
Connect using an active Wi-Fi network:
Open the PowerView ® App on your mobile device and follow
the on-screen instructions to properly connect to an active
Wi-Fi network. The Hub will continue to blink AMBER, once
the Hub has been connected to the home network.
Connect Hub to Internet connected wireless router.
CON NEC T IONS
If you have already established a PowerView ® Shade Network
between a PowerView ® Remote and PowerView shades, you should
pair the Hub to the same network. To pair the Hub to the same
network, open the PowerView ® App and follow the prompts. The
Hub LED will turn to solid BLUE, once the Hub has been paired to
the PowerView Shade Network.
Pairing your Hub with an existing
PowerView® Shade Network.
Note: Do not expose the PowerView® Repeater to direct sunlight.
Distribute Repeater(s) as needed.
CON NEC T IONS
Test signal to Repeater(s).
Press and hold the P button on the back of the PowerView ® Hub.
The light on each Repeater should blink BLUE. If the Repeater
does not blink BLUE, move the Repeater closer to the Hub or
pair the Repeater to the correct PowerView ® Shade Network.
Other controls on the back of the Hub include the R button
which power cycles the Hub and erases all Hub data when
pressed and held for 6 seconds.
Transfer your hub data (if needed).
If you have a Gen 1 Hub (above left) on your PowerView ® Shade
Network, follow in-app instructions to transfer Hub data to the
new PowerView ® Hub.
CON NEC T IONS
hunterdouglas.com/operating-systems/powerview-motorization
For more information about the setup and use of the
PowerView ® App, please visit:
You’re ready to use the PowerView® App.
Note: The LED of secondary Hubs will display solid GREEN, once paired
to the PowerView Network.
After a primary Hub has been paired to the PowerView ®
Network, each subsequent Hub paired to the same network
will automatically be configured as a network access point.
Please follow in-app instructions to install secondary Hubs.
Configuring multiple Hubs on one
PowerView® Network (Optional).
11
CON NEC T IONS
hunterdouglas.com/operating-systems/powerview-motorization
To learn more about integration, please contact your
local Hunter Douglas dealer or visit:
PowerView® Motorization integrates with a variety of
leading third-party control systems and devices.
13
HOME AU TOM AT ION IN T EGR AT ION
Hub is updating firmware from the Internet.
Connected, normal operation.
Hub is Transmitting command(s) to the
PowerView Shade Network.
Hub is not connected to power or Hub LED
functionality has been switched off.
Hub is configured as a secondary Hub.
Solid AMBER
Solid BLUE
Flashing BLUE
Blank
Solid GREEN
• Check that the mobile device is on the same network as
wireless router.
• Check the connection between the Hub and wireless router and
that the router is operating properly.
• Check for blinking AMBER or solid BLUE on the front of the Hub.
(See LED Feedback chart above.)
Problem: Cannot connect to the Hub
with the PowerView ® App.
Hub is not connected to PowerView ®
Shade Network.
Blinking AMBER
PowerView ® LED Feedback
European Conformity
We, the undersigned,
Hunter Douglas Window Fashions
One Duette Way, Broomfield, CO 80020, USA
Hunter Douglas Europe B.V.
Piekstraat 2, 3071 EL Rotterdam, The Netherlands
certify and declare under our sole responsibility that the PowerView® Hub conforms with the essential
requirements of the EMC directive 2004/108/EC and R&TTE directive 1999/5/EC.
A copy of the original declaration of conformity may be found at
www.hunterdouglas.com/RFcertifications.
Industry Canada
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type
and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Class B Digital Device Notice
This Class B digital apparatus complies with Canadian ICES-003, RSS-Gen and RSS-210.
CAN ICES-3 (B)/NMB-3(B)
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment
and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed
and operated keeping the radiator at least 20cm or more away from person’s body.
U.S. Radio Frequency FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment
and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed
and operated keeping the radiator at least 20cm or more away from person’s body. RF Exposure
requirements are met when installed in mobile equipment. This module cannot be installed in portable
equipment without further testing and a change to FCC’s grant of authorization. Contact Murata
regarding portable applications.
15
T ROUBLESHOOT ING

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 9
Producer                        : Nitro PDF PrimoPDF
Create Date                     : 2018:03:19 11:09:39+06:00
Modify Date                     : 2018:03:19 11:09:39+06:00
Title                           : Hub Guide English Rev 1.pdf
Creator                         : PrimoPDF http://www.primopdf.com
Author                          : jbaugh

EXIF Metadata provided by EXIF.tools