Hunter Engineering Rx10 Rx12 Scissor Brochure & Lifts Maximum Productivity, Minimum Space

2015-07-28

: Hunter-Engineering Hunter-Engineering-Rx10-Rx12-Scissor-Brochure-780070 hunter-engineering-rx10-rx12-scissor-brochure-780070 hunter-engineering pdf

Open the PDF directly: View PDF PDF.
Page Count: 8

RX10 & RX12 Scissor Lifts
Maximum Productivity, Minimum Space
RX Scissor Lift
Large capacity with a
small footprint
Safety Locks
Extra-Wide Runways
✔ 24" runways accept
wide vehicles
small footprint
small footprint
✔
24" runways accept
24"
Velocity Safety Fuses
✔ Instantaneous
shutdown
in event of
hydraulic
failure
Sensor Feedback System*
✔ Sensors keep runway level
✔ Safely stops if obstructed
Sensor Feedback System
Sensor Feedback System
* Shown with protective cover removed.
Integrated Air Line Kit
✔ Convenient air source
for tools at front and rear
Best-In-Class Drive-On Height
✔ Maximize
ground clearance
ground clearance
Best-In-Class Drive-On Height
Two Swing Air Jacks
1110987654321 12
1110987654321 12
1110987654321 12
11"
OTHERS 10"
RX12 8.75"
RX10
Pins and Bearings
✔Chromed
pins and
teflon
bearings for
long life
Safety Locks
✔ Precision-fit
teeth lock
runways at
16 level height
positions
Control Panel
✔ Complete operation from
the console
✔ Optional PowerSlide,
Inflation Station and FIA
control
Control Panel
Inflation Station (optional)
✔ Automatically fills or
bleeds each tire
✔ No hanging air lines
Louvered Ramps
✔ Prevent wheel spin in
wet conditions
✔ More effective than
diamond tread or
abrasive strips
Louvered Ramps
RX10LT-IS shown with
optional light kit
Two Movable Work Steps
✔ 12 secure
positions
✔ Lightweight
design
Two Movable Work Steps
Two Swing Air Jacks
✔ 6,000-lb.
capacity
✔ Technicians’
favorite
capacity
favorite
Fast Descent Speed
The hydraulic system speeds lowering times
by 50%.
The system automatically slows the descent in
the last several inches to ensure a soft landing.
The fast descent feature is standard
with Inflation Station (IS) models.
Swing Air Jacks
Hunter Swing Air Jacks add capabilities
for lifting vehicles off the runways during alignment
procedures and other multi-service operations.
Each 6,000-lb. (2,722 kg) capacity Swing Air Jack
combines low drive-on height with high lifting
capacity needed to handle a wide range of vehicles.
133-69-1 – 6,000-lb. Capacity Swing Air Jack
Flush-Mount Installation
Lifts may be flush-mounted in a shallow recess.
No more worries about lowered vehicles or
expensive spoilers! This very tidy installation is
ideal for “showcase” shops.
No additional charge for flush-mount option.
Contact your Hunter Sales Representative
for details.
Add F to any RX model number.
STANDARDFAST
Descent
0:25 0:50
AlignLights System
Hunter’s integrated AlignLights LED lighting system
provides a bright and efficient light source underneath
the vehicle.
AlignLights automatically turns on when the lift is
raised and turns off when the lift is lowered to the floor.
AlignLights is an ALI-listed accessory.
20-2766-1 – AlignLights system
Approach Ramp Extensions
Stage 2 RX Approach Ramp Extensions
147-113-1 –
Standard with RX12A.
Optional with RX10,
adds 12.75" to length.
(2 required)
Stage 2 RX Approach Ramp Extensions
147-113-1
Standard with RX12A.
Optional with RX10,
adds 12.75" to length.
(2 required)
Conversion Kits
Drive-Thru Conversion Kit
20-2498-1 – RX10, RX12A and RX16 drive-thru kit for
camera sensors adds 52" to overall length.
20-2501-1 – RX10, RX12A and RX16 drive-thru kit for
conventional sensors adds 63" to overall length.
20-2169-1 –
Adds 27.25" to RX10
or 22.25" to RX12A.
20-2189-1 –
Adds 37.25" to RX10
or 32.25" to RX12A.
20-2169-1
Adds 27.25" to RX10
or 22.25" to RX12A.
20-2189-1
Adds 37.25" to RX10
or 32.25" to RX12A.
✔ Stainless steel turnplates
(PowerSlide turnplates on PS and IS models)
Standard Equipment
OPTIONAL
✔ Flush-mounted, full-floating slipplates
(PowerSlide slipplates on PS and IS models)
✔ Two movable work steps
(not included with flush-mount installations)
✔ Louvered ramps with built-in wheel stops
✔ Front wheel stops
✔ Two wheel chocks
✔ Built-in, full-length jack rails
✔ Built-in air line kit
OPTIONAL
OPTIONAL
Hunter Offers Two Fully Integrated
Options to Enhance Productivity
Shown with optional aligner console, sensors, bar code reader, target support brackets, and lights.
FIA allows WinAlign® aligners to control the lift features
for ultimate productivity. Two patented designs
offer greater flexibility and timesaving capabilities.
** Requires FIA equipped aligner with WinAlign 10.x software or greater.
Printouts show starting and
fi nal tire pressures.
**
POWERSLIDE EDITION
INFLATION STATION EDITION
Minimize trips around the car
Mount Targets
1
Make Adjustments
2
Remove Targets
3
5Lower Leveling Legs (if equipped)
5
Lower Leveling Legs (if equipped)
Jack Vehicle and Compensate Sensors
4
Jack Vehicle and Compensate Sensors
4
Remove Slipplate and Turnplate Pins
6
Remove Slipplate and Turnplate Pins
6
7Replace Slipplate and Turnplate Pins
7
Replace Slipplate and Turnplate Pins
Raise Leveling Legs (if equipped)
8
Raise Leveling Legs (if equipped)
8
Only
3 Trips!
123
87654321
Yesterday's
Technology
8 Trips
✔ Includes PowerSlide® slipplates
and turnplates
✔ Automatically infl ate all four tires
simultaneously
✔ Record starting and fi nal pressure**
✔ Hose recoils to keep work area clear
✔ Locks slipplates and turnplates with the
touch of a button or automatically through
an FIA-equipped aligner**
✔ No more struggles with lock pins
✔ Avoid wear and tear and extend the life of
your turnplates
Alignment height All lock positions
Tread width
Min. inside 40” (1016 mm)
Max. outside 88” (2235 mm)
Motor 208-230 VAC,
60 Hz, 26A, 1 ph
Air 90-150 psi
Speed 55 seconds (raise)
25-50 seconds (descent)
RX Specifi cations
Form 6175-T, 07/14
Supersedes Form 6175-T, 03/14
Copyright © 2014, Hunter Engineering Company
www.hunter.com
Models
RX10JT: RX10 with (2) 6,000-lb. Swing Air Jacks
and stainless steel turnplates
RX10LJT: Long-deck RX10 with (2) 6,000-lb. Swing
Air Jacks and stainless steel turnplates
RX10T-PS: RX10 with (2) 6,000-lb. Swing Air Jacks,
PowerSlide slipplates and turnplates,
and FIA
RX10LT-PS: Long-deck RX10 with (2) 6,000-lb.
Swing Air Jacks, PowerSlide slipplates
and turnplates, and FIA
RX10T-IS: RX10 with (2) 6,000-lb. Swing Air Jacks,
PowerSlide slipplates and turnplates,
Inflation Station, and FIA
RX10LT-IS: Long-deck RX10 with (2) 6,000-lb.
Swing Air Jacks, PowerSlide slipplates
and turnplates, Inflation Station, and FIA
RX12AJT: RX12 with (2) 6,000-lb. Swing Air Jacks
and stainless steel turnplates
RX12AT-PS: RX12 with (2) 6,000-lb. Swing Air Jacks,
PowerSlide slipplates and turnplates,
and FIA
RX12AT-IS: RX12 with (2) 6,000-lb. Swing Air Jacks,
PowerSlide slipplates and turnplates,
Inflation Station, and FIA
Add F to any RX model number (ex. RX10LJFT) for
fl ush-mount installation
Max. vehicle weight:
Max. wheelbase: General service
Two-wheel alignment
Four-wheel alignment
Min. four-wheel alignment:
Runway width:
Lowered height:
Max. lifting height:
RX12A
12,000 lbs. (5443 kg)
184”/180” (4673/4572 mm)
179”/175” (4547/4445 mm)
158” (4013 mm)
88” (2235 mm)
24” (609 mm)
10” (254 mm)
71” (1803 mm)
RX10L
10,000 lbs. (4536 kg)
184”/180” (4673/4572 mm)
179”/175” (4547/4445 mm)
158” (4013 mm)
88” (2235 mm)
24” (609 mm)
8.75” (222 mm)
72” (1829 mm)
RX10
10,000 lbs. (4536 kg)
171”/167” (4343/4241 mm)
166”/162” (4216/4115 mm)
158” (4013 mm)
88” (2235 mm)
24” (609 mm)
8.75” (222 mm)
72” (1829 mm)
surface/
flush
16
(406 mm)
IN.
22
(559 mm)
IN.
24 IN.
(610 mm)
LEAVE AMPLE WORKSPACE BETWEEN
EQUIPMENT AND LIFT RACK
7 FT. - 4 1/2 IN.
(2248 mm)
FOR
RX10 MODELS,
IN.20 FT. - 1 1/4
(6128 mm)
FOR
RX10L MODELS,
21 FT. - 2 1/4 IN.
(6458 mm)
39 - 54
(991 - 1372 mm)
IN.
PRIOR TO LIFT INSTALLATION:
INSTALL 230VAC, 1 PHASE,
60 HZ FOR 26 AMP DRAW NEAR
CONTROL CONSOLE LOCATION.
90-150 PSI (6.2-10.3 BAR) SHOP
AIR MUSTALSO BE SUPPLIED.
16
(406 mm)
IN.
11 5/8 IN.
(295 mm)
OPTIONAL
EXTENDED
WHEEL STOP
FOR
RX12A MODELS,
IN.22 FT. - 2
(6756 mm)
Be sure to check out other Hunter
literature for more quality products
from Hunter Engineering.
Because of continuing technological advances, specifications,
models and options are subject to change without notice.
See Hunter Sales Representative for details on site requirement.
RX Plan View
0714FAP7.5M.34
The Hunter RX10 and RX12A Scissor Lifts have been certified
under the program conducted by Automotive Lift Institute (ALI)
and ETL Testing Laboratories to comply with Safety Standard
ANSI/ALI, ALCTV and Electrical Standard ANSI/UL 201.

Navigation menu