Hunter Engineering Rx16 Scissor Brochure Lift Low, Long, Fast And Strong

: Hunter-Engineering Hunter-Engineering-Rx16-Scissor-Brochure-780080 hunter-engineering-rx16-scissor-brochure-780080 hunter-engineering pdf

Open the PDF directly: View PDF .
Page Count: 8

RX16 Scissor Lift

Low, Long, Fast and Strong

NEW!

RX16 Scissor Lift

Massive capacity with

a small footprint

Extra-Wide Runways

✔ 26" runways accept

wide, heavy vehicles

✔

26" runways accept

Sensor Feedback System*

✔ Sensors keep runways level

✔ Safely stops if obstructed

Sensor Feedback System

Sensor Feedback System

* Shown with protective cover removed.

Two Swing Air Jacks

Two Swing Air Jacks

Velocity Safety Fuses

✔ Instantaneous shutdown

in event of hydraulic

failure

Instantaneous shutdown

*** For surface-mount models.

Power-Up System

✔ Standard-capacity mode easily

handles most vehicles, including

those with low ground clearance

a small footprint

Extra-Wide Runways

a small footprint

Safety Locks

✔ Precision-fit teeth lock

runways at 15 level

height positions

Safety Locks

Safety Locks

26"

Best-In-Class Drive-On Height

✔ Only 9"

fully lowered***

✔ No clearance

problems

fully lowered***

problems

Best-In-Class Drive-On Height

1110987654321 12

9"

Velocity Safety Fuses

Velocity Safety Fuses

Power-Up System

Power-Up System

**

** Patent pending.

Control Panel

✔ Complete operation from

the console

✔ Optional PowerSlide,

Inflation Station and

FIA control

Control Panel

Inflation Station (optional)

✔ Automatically fills or

bleeds each tire

✔ No hanging air lines

Louvered Ramps

✔ Prevent wheel spin in

wet conditions

✔ More effective than

diamond tread or

abrasive strips

Louvered Ramps

Two Swing Air Jacks

✔ 9,000-lb.

capacity

✔ Technicians’

favorite

capacity

favorite

RX16T-IS shown with

optional light kit

✔ Power-Up engages to lift heavy

vehicles (up to 16,000 lbs.) when

ground clearance is not an issue

Inflation Station (optional)

Inflation Station (optional)

Two Movable Work Steps

✔ 13 secure

positions

✔ Lightweight

design

Raise Height

✔Class-leading 76"

maximum height***

Raise Height

Raise Height

Class-leading 76"

76"

Fast Descent Speed

Power-Up System

The hydraulic system speeds lowering times

by 50%.

The system automatically slows the descent in the

last several inches to ensure a soft landing.

Hunter’s dual-capacity lifting system offers the

ground-clearance advantages of a standard-

capacity lift to handle most vehicles.

To service heavy vehicles, the exclusive Power-Up

feature boosts lifting capacity to a massive 16,000 lbs.

Only Hunter’s RX16 combines the versatility of a

low-profile design with tremendous power to

provide the widest range of service with one lift.

Flush-Mount Installation

RX16 lifts may be flush-mounted in a shallow

recess. No more worries about lowered vehicles

or expensive spoilers! This tidy installation is

ideal for “showcase” shops.

Because drive-on height is not an issue for flush-

mount versions, dual-capacity system is not used.

Each flush-mount RX16 uses a 16,000-lb.

capacity standard lifting system with 72”

maximum raise height.

Add F to any RX16 model number.

Conventional

Systems

FAST

Descent 0:60

0:25

20-2169-1 – Adds 40".

20-2189-1 – Adds 50".

Approach Ramp Extensions Conventional Sensor Extension Drive-Thru Kit

For surface-mount, drive-thru

application. Use standard kit for

camera sensors and extended

kit for conventional sensors.

20-2498-1 – Standard kit for camera

sensors. Adds 53" in length.

20-2501-1 – Extended kit for

conventional sensors. Adds 61"

in length.

20-2498-1 – Standard kit for camera

Provides additional space at the

front of runways. Required when

using conventional sensors with

toe arms.

20-2497-1 – Adds approximately

12" in length.

20-2497-1 – Adds approximately

Extensions lessen the ramp incline

for high-floor-slope installs and

ease service for specialty vehicles.

147-104-1 – Adds

13" (2 required).

147-113-1 – Adds

18" (2 required).

147-104-1 – Adds

20-2169-1 – Adds 40".

OPTIONAL OPTIONAL OPTIONAL

Swing Air Jacks

Hunter Swing Air Jacks add capabilities

for lifting vehicles off the runways during alignment

procedures and other multi-service operations.

Each 9,000-lb. (4,082 kg) capacity Swing Air Jack

combines low drive-on height with high lifting capacity

needed to handle a wide range of vehicles.

133-83-1 – 9,000-lb. Capacity Swing Air Jack

AlignLights System

Hunter’s integrated AlignLights lighting system provides

an efficient light source underneath the vehicle.

AlignLights automatically turns on when the lift is

raised and turns off when the lift is lowered to the floor.

AlignLights is an ALI-listed accessory.

20-2173-1 – AlignLights system

OPTIONAL

Shown with optional aligner console, sensors, bar code reader, target support brackets, and lights.

Hunter Offers Two Fully Integrated

Options to Enhance Productivity

FIA allows WinAlign® aligners to control lift features

for ultimate productivity. Two patented designs

offer greater flexibility and timesaving capabilities.

** Requires FIA equipped aligner with WinAlign 10.x software or greater.

✔ Locks slipplates and turnplates with the

touch of a button or automatically through

an FIA-equipped aligner**

✔ No more struggles with lock pins

✔ Avoid wear and tear and extend the life of

your turnplates

POWERSLIDE EDITION

INFLATION STATION EDITION

Minimize trips around the car

Mount Targets

1

Make Adjustments

2

Remove Targets

3

5Lower Leveling Legs (if equipped)

5

Lower Leveling Legs (if equipped)

Jack Vehicle and Compensate Sensors

4

Jack Vehicle and Compensate Sensors

4

Remove Slipplate and Turnplate Pins

6

Remove Slipplate and Turnplate Pins

6

7Replace Slipplate and Turnplate Pins

7

Replace Slipplate and Turnplate Pins

Raise Leveling Legs (if equipped)

8

Raise Leveling Legs (if equipped)

8

Only

3 Trips!

123

87654321

Yesterday's

Technology

8 Trips

Printouts show starting

and

fi nal tire pressures.**

✔ Includes PowerSlide® slipplates

and turnplates

✔ Automatically infl ate all four tires

simultaneously

✔ Record starting and fi nal pressure**

✔ Hose recoils to keep work area clear

RX16 Specifi cations

Form 6386-T, 07/14

Supersedes Form 6386-T, 05/14

Copyright © 2014, Hunter Engineering Company

www.hunter.com

RX16 Plan View

Be sure to check out other Hunter literature for more

quality products from Hunter Engineering.

Max. vehicle weight: 16,000 lbs. (7257 kg)

Max. lifting height:

16,000-lb. mode 68" (1727 mm)

Standard-capacity mode 76" (1930 mm)

Flush-mount version 72" (1829 mm)

Alignment height: All lock positions

Lifting speed: 60 seconds

Lowering speed: 25 seconds

Models

Standard Equipment

Stainless steel turnplates (PowerSlide turnplates on

PS and IS models)

Flush-mounted, full-floating slipplates (PowerSlide

slipplates on PS and IS models)

Two movable work steps (not included with

flush-mount installations)

Louvered ramps with built-in wheel stops

Front wheel stops

Two wheel chocks

Built-in, full-length jack rails

Built-in air line kit

See Hunter Sales Representative for details on

site requirement.

0714CAP7.5M.33

RX16JT: RX16 with (2) 9,000-lb. Swing Air Jacks

and stainless steel turnplates

RX16JFT: Flush-mount RX16 with (2) 9,000-lb. Swing

Air Jacks and stainless steel turnplates

RX16T-PS: RX16 with (2) 9,000-lb. Swing Air Jacks,

PowerSlide slipplates and turnplates,

and FIA

RX16FT-PS: Flush-mount RX16 with (2) 9,000-lb.

Swing Air Jacks, PowerSlide slipplates

and turnplates, and FIA

RX16T-IS: RX16 with (2) 9,000-lb. Swing Air Jacks,

PowerSlide slipplates and turnplates,

Inflation Station, and FIA

RX16FT-IS: Flush-mount RX16 with (2) 9,000-lb.

Swing Air Jacks, PowerSlide slipplates

and turnplates, Inflation Station, and FIA

The Hunter RX16 Series Scissor Lift has been

certified under the program conducted by

Automotive Lift Institute (ALI) and ETL Testing

Laboratories to comply with Safety Standard ANSI/

ALI, ALCTV and Electrical Standard ANSI/UL 201.

Tread width:

Min. inside 40" (1016 mm)

Max. outside 92" (2337 mm)

Max. wheelbase:

General service 187" (4749 mm)

Two-wheel alignment 182" (4623 mm)

Four-wheel alignment 158" (4013 mm)

Min. four-wheel alignment: 88" (2235 mm)

16"

(406 mm)

4" (101 mm) RECOMMENDED MIN.

22"

(559 mm)

26"

(660 mm)

LEAVE AMPLE WORKSPACE BETWEEN

EQUIPMENT AND LIFT RACK

ALIGNMENT EQUIPMENT

7' - 8 1/2"

(2350 mm)

FOR RX16JT,

RX16T-PS AND

RX16T-IS

21' - 5 1/2"

(6541 mm)

LIFT

LENGTH

39 - 54"

(991 - 1372 mm)

PRIOR TO LIFT INSTALLATION:

INSTALL 230 VAC, 1 PHASE,

60 HZ FOR 26 AMP DRAW NEAR

CONTROL CONSOLE LOCATION.

90-150 PSI (6.2-10.3 BAR) SHOP

AIR MUST ALSO BE SUPPLIED.

16"

(406 mm)

11 5/8''

(295 mm)

OPTIONAL

EXTENDED

WHEEL STOP