Hunter Fan 28343 Users Manual 41490 01
28405 cedcebf1-6890-4c3f-8009-3c291c79d0b2
28982 to the manual c2ac56ae-84b0-4d39-873b-dbff3ffbafd3
2015-01-24
: Hunter-Fan Hunter-Fan-28343-Users-Manual-340970 hunter-fan-28343-users-manual-340970 hunter-fan pdf
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
INSTALLATION INSTRUCTIONS FOR HUNTER CEILING FAN LIGHT KITS MODELS: 28330, 28331, 28332, 28333, 28334, 28335, 28336, 28337, 28338, 28339, 28340, 28341, 28342 28343, 28344, 28345, 28405, 28406, 28407, 28408, 28982, 28983, 28984, 28985, 28986, 28987 Light K it Lead W ires and W ire Nuts C AUTIONS • Read entire text carefully before beginning installation and save these instructions. • To reduce the risk of electrical shock, install this light kit only on listed Hunter ceiling fan models: C ote D’ Azur , C ustom Home 2 , Captiva , 44” Dominion , Designer’s Choice , ORBit , 52” Dominion , M arseille , Santa Barbara , Belle Meade & Etruscan Bellmouth Nut Fan Speed Switch Capacitor Capacitor WARNING • To avoid possible electrical shock, before installing light fixtures, disconnect power by turning off the circuit breakers both to the outlet box and to its associated wall switch location. If you cannot lock the circuit breakers in the off position, securely f asten a prominent warning device, such as a tag, to the service panel. • C onnect house wiring to the fan before attaching the light fixture to the fan. • All wiring must be in accordance with national and local electrical codes and A NSI/ NFPA 70. If you are unfamiliar with wiring, you should use a qualified electrician. M ulti-wire Plug Connection M 3 Housing A ssembly Screws Reverse Switch FIGURE 1 4. Locate and carefully remove the two capacitors from the switch housing. 5. You have now disconnected the wiring harness and its components from the switch housing and are ready to install them into the modular accessory light kit. STEP 2: INSTALLING WIRING HARNESS STEP 1: REMOVING WIRING HARNESS NOTE: Refer to Figure 1 for steps listed below. Before you can install the modular accessory light kit, you must remove the wiring harness and its components from the modular switch housing on the fans listed above. You must then install the wiring harness into the modular accessory light kit. 1. Locate the two wires in the lower switch housing labeled “ Connect Light Here” or “ For Light Use” . One will be white, the other black/white. Unscrew the wire nuts counterclockwise to expose the bare metal leads. NOTE: Refer to Figure 1 for the steps listed below. 2. Locate the white wire and the black wire coming from the light fixture. 1. Locate the reversing switch and carefully remove the two screws holding the reversing switch to the switch housing. The reversing switch can now be removed from the switch housing. Connect the black wire from the light fixture to the black/white wire from the lower switch housing. 2. Remove the patented breakaway connector from the fan pull chain. Connect the white wire from the light fixture to the white wire from the lower switch housing. 3. Carefully loosen the bellmouth nut from the fan pull chain and remove the fan pull chain switch from the switch housing. To fasten the wires, twist the two bare leads together. Place a wire nut over the intertwined length of wire and twist clockwise until tight. 41490-01 12/01/2005 W ires to Light Sockets Bellmouth Nut Bellmouth Nut Fan Speed Switch Light Switch Capacitor Capacitor M ulti-wire Plug Connection #6-62 Housing A ssembly Screws Reverse Switch FIGURE 2 CAUTION Be sure no bare wire or wire strands are visible after making connections. 3. Insert the chain and fan pull chain switch through the round opening on the side of the modular accessory light kit. Thread the bellmouth nut over the pull chain and hand tighten the bellmouth nut. 4. Reattach the patented breakaway connector to the end of the pull chain. 5. Insert the reversing switch into the square hole on the side of the modular accessory light kit. Install and tighten the two screws you removed in Step 1, substep 1. 6. Carefully place the capacitors in the modular accessory light kit. You have completed the assembly of the modular accessory light kit and are ready for installing the modular accessory light kit to the fan. UPPER SW ITCH HO USING UPPER PLUG CO NNECTO R LO W ER PLUG CO NNECTO R LIGHT K IT HOUSING A SSEM BLY SCREW FIGURE 3 2. Place the modular accessory light kit over the upper switch housing. Align the side screw holes in the upper switch housing and the modular accessory light kit. Attach the modular accessory light kit to the upper switch housing with the three #6-32 X 3/8" housing assembly screws. STEP 4: INSTALLING THE BULBS AND GLOBES NOTE: Refer to Figure 4 for the steps listed below. 1. Insert a globe into the cup. 2. Tighten the thumbscrews manually. Do Not overtighten. 3. Repeat substeps 1 and 2 for the remaining three globes. 4. Install a 60W medium base incandescent bulb into each socket. You have completed the installation of the modular accessory light kit. Refer back to the “ Operating Your Hunter Fan” section in the Installation/Owner’s Manual provided with your Hunter fan for proper operation instructions. STEP 3: INSTALLING THE ACCESSORY LIGHT KIT NOTE: Refer to Figure 3 for the steps listed below. 1. C onnect the lower (mutli-wire) plug connector from the modular accessory light kit to the upper plug connector from the motor. NOTE: Both plug connectors are polarized and will only fit together one way. Make sure that both connectors are properly aligned before connecting them together. Incorrect connection could cause improper operation and damage to the product. THUM BSCREW S CUP GLOBE FIGURE 4 Hunter Fan C ompany 2500 Frisco Avenue Memphis, TN 38114 U SA © 2005 Hunter Fan Co. 41490-01 12/01/2005
Source Exif Data:
File Type : AI File Type Extension : ai MIME Type : application/vnd.adobe.illustrator PDF Version : 1.5 Linearized : No Page Count : 2 For : Hunter Employee, Hunter Fan Company Create Date : 12/1/2005 5:23 PM Bounding Box : 34 19 578 775 Creator Version : 10 Container Version : 9 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:eee44086-7d93-4946-8c2c-d7fa4f2b411a Producer : Acrobat Distiller 5.0.5 (Windows) Keywords : Modify Date : 2005:12:01 17:26:32-06:00 Metadata Date : 2005:12:01 17:26:32-06:00 Creator Tool : Adobe PageMaker 7.0 Document ID : uuid:8aebe885-a2fc-45d2-b8ae-096543ece99e Format : application/pdf Creator : rperkins Title : 41490-01 Description : 41490-01 Author : rperkins Subject : 41490-01 Image Height : 756 Image Width : 544 Image Size : 544x756 Megapixels : 0.411EXIF Metadata provided by EXIF.tools