Hunter Fan Ceiling Light Kits Users Manual 41558 01

Ceiling Fan Light Kits to the manual f6e21dec-838a-43c1-86d1-c896a733039f

: Hunter-Fan Hunter-Fan-Ceiling-Fan-Light-Kits-Users-Manual-341063 hunter-fan-ceiling-fan-light-kits-users-manual-341063 hunter-fan pdf

Open the PDF directly: View PDF .
Page Count: 3

© 2003 Hunter Fan Company 1 41558-01 3-6-2003

· Read entire text carefully before

beginning installation and save these

instructions.

· To reduce the risk of electrical shock,

install this light kit only on listed Hunter

ceiling fans type A through Z.

CAUTIONS

· To avoid possible electrical shock, before

installing light fixtures, disconnect power

by turning off the circuit breakers both

to the outlet box and to its associated wall

switch location. If you cannot lock the

circuit breakers in theoff position,

securely fasten a prominent warning

device, such as a tag, to the service panel.

· Connect house wiring to the fan before

attaching the light fixture to the fan.

· All wiring must be in accordance with

national and local electrical codes. If you

are unfamiliar with wiring, you should use

a qualified electrician. Professional

installation is recommended.

WARNINGS

1. Unassemble the fan switch housing as shown in

Figure 1.

2. Disconnect the upper and lower plug connectors

between the upper switch housing and lower

switch housing.

Note: Do not discard any parts. You will need to

replace it if you remove the light fixture in the

future.

Figure 1 - Unassembling the fan switch housing

Preparing for Installation

Installation Instructions

For Hunter Ceiling Fan Light Kits

Aurora Style

Upper Switch

Housing

Switch

Housing

Cover

Plate

Plug Button

Lower

Switch

Housing

Switch Housing

Assembly Screws

Switch

Housing

Assembly

Screws

41558-01 3-6-2003 2 © 2003 Hunter Fan Company

1. Insert the black wire and white wire from the

light kit assembly through the hole in the bottom

of the lower switch housing. Refer to Figures 2

and 3.

2. Securely tighten the light kit assembly into the

bottom of the lower switch housing. Refer to

Figure 3.

3. Install the nut and washer onto the end of the

light kit assembly inside of the lower switch

housing. Securely tighten the nut and washer.

Insert and tighten the two #6-32 sems light

fixture mounting screws. Refer to Figure 3.

4. Using the wire nuts on the two light kit wires in

the lower switch housing, connect the black wire

from the light kit assembly to the black/white

wire from the lower switch housing and connect

the white wire from the light kit assembly to the

white wire from the lower switch housing.

5. Reconnect the upper plug connector from the

upper switch housing to the lower plug connector

in the lower switch housing. Refer to Figure 4.

Note: Both plug connectors are polarized and will

only fit together one way. Make sure that both

connectors are properly aligned before connecting

them together. Incorrect connection could cause

improper operation and damage to the product.

6. Align the holes in the upper switch housing and

the lower switch housing. Securely tighten the

three switch housing screws assembly screws.

Refer to Figure 1 and 4.

Figure 2 - Assembling

the Light Kit

Figure 3 - Attached Light

Kit Assembly

Installing the Light Fixture

Figure 4 - Connecting the Plug Connectors

Upper Plug

Connector Lower Plug

Connector

Upper

Switch

Housing

Light Kit

Assembly

Lower

Switch

Housing

© 2003 Hunter Fan Company 3 41558-01 3-6-2003

Pipe

Globe Metal Disk

Bulb

Socket

Light

Switch Pull

Chain

Cover Plate

Finial

Fan Switch

Pull Chain

Hunter Fan Company

2500 Frisco Avenue

Memphis, Tennessee 38125

United States of America

Figure 7 - Aurora Fixtures

Installing Globes and Bulbs

Thread the fan switch pull chain through the

grommetted hole in the light fixture bracket. Unfasten

the extra chain looped through the hole in the in the

lower mounting cap and attach it to the fan switch

pull chain. Repeat for light switch pull chain.

Refer to Figures 5, 6 and 7.

1. Install bulbs. Use 60W Max, A-15 bulbs.

2. Thread the fan switch pull chain through the hole in

the metal disk.

3. Place globe on pipe until flush against metal disk.

4. Thread the light switch pull chain through the large

center opening of the globe.

5. Thread the fan switch pull chain through the small

center opening in the globe.

6. Place the cover plate up against the underside of

the globe. Pass light and fan switch pull chains

through the appropriate holes.

7. Thread the light switch pull chain through the

finial and screw the cap onto the pipe end until

tight.

Figure 6 - Attaching Fan Switch Pull Chain Extension

Figure 5 - Threading Fan Switch Pull Chain through

Grommet

Grommetted

Hole

Lower Mounting Cap

Extra Chains

Hole in Lower

Mounting Cap