Hunter Fan TX27 Ceiling fan remote control transmitter User Manual 41475 01

Hunter Fan Company Ceiling fan remote control transmitter 41475 01

User manual

Form # 41476-01 Rev. 2-23-2001Hunter Fan CompanyIntegrated Remote ControlInstruction Supplement®Transmitter Model: 85095Transmitter Battery: 12 V, Type 23A, MN-21 or equivalentReceiver Model: 85069Ratings: 120 VAC, 60 Hz,1.0 Amp FanReceiver Weight: 8 oz.240 Watts incandescent lightRead and Save these InstructionsYour fan is equipped to be operated by remote control. A receiver device ismounted inside the fan switch housing. A hand-held transmitter is packedin the fan box. The transmitter requires a 12-volt battery (included). Theoperating range is 15-30 feet.Setting The CodeWhen two or more fans are located near each other, you may desire to haveeach of them set to a different code, so that the operation of one fan willnot affect another. This is accomplished by changing the position of anyone or more of a group of 3 jumpers grouped together in the transmitter.The receiver located in the switch housing has the same set of 3 jumperswhich must also be changed to match the transmitter settings.These jumpers are very small and can best be operated by using a small pairof pliers or tweezers.In the transmitter, the jumpers are readily accessible from the battery com-partment. The switches in the receiver are located at the bottom of thereceiver device in the switch housing. See Figures 1 and 2.To set the jumpers in the receiver, remove the receiver from the switch housingand set the jumpers in the same positions as the jumpers in the transmitter.See Figure 2.Replace the receiver, making sure the mounting holes at the top of theswitch housing line up with the matching slots in the top of the receiver.Figure 4 - Remote Holder AssemblyJumperSwitchTransmitterBackFigure 1 - Transmitter Jumper SwitchesFigure 2 - Receiver Jumper SwitchesUpper SwitchHousingLower SwitchHousingPlug ConnectorAssemblyScrewFigure 3 - Lower Switch Housing AssemblyIf the two pieces are difficult to assemble, check the alignment of the (3)slots in the top of the receiver module and the mounting holes in the lowerswitch housing. They should align together.Tighten the (3) assembly screws.CAUTION: Make sure the screws are snug, otherwise the assembly couldseparate during operation.Mounting the Remote HolderA holder is supplied with the transmitter which can be mounted to a exist-ing toggle switch wall plate. The holder will help prevent misplacement ofyour transmitter by providing a permanent receptacle. See Figure 4.If desired, the holder can be mounted to a convenient location on a wall.Assembling The Switch HousingAssemble the lower switch housing to the upper housing. See Figure 3.First insert the plug from the upper housing into the plug receptacle in thereceiver module.NOTE: The plug is polarized and will only go together one way. Make sureyou have correctly aligned plug and receptacle.Next, line up the lower switch housing with the upper housing and as-semble together with the (3) screws and lockwashers provided. See Figure3.JumperSwitchReceiverBottomLower Switch HousingPull receiver outof switch housing.Caution: Risk of Electrical Shock!All wiring must be performed in accordance with national and local electri-cal codes. If you are unfamiliar with the wiring codes, you should use aqualified electrician.To avoid overheating and possible damage to other equipment, do notinstall to control a receptacle, fluorescent light fixture, motor operated ap-pliance, or transformer-supplied appliance. Use only to control one paddle-blade ceiling fan and incandescent light fixture.This device complies with part 15 of the FCC rules. Changes or modifica-tions not expressly approved by Hunter Fan Company could void your au-thority to operate this equipment!Operation Is Subject To The Following Two Conditions:1. This device may not cause harmful interference.2. This device must accept any interference received, including interfer-ence that may cause undesired operation.Note: Any changes or modifications to the transmitter or receiver not ex-pressly approved by Hunter Fan Company may void one’s authority to oper-ate this remote control.
Form # 41476-01 Rev. 2-23-2001Symptom Possible Causes SolutionTroubleshooting1. No functions operate.2. Operates only at close range.3. Inconsistent operation.Main Power not restored. Replace fuse. Turn ON circuit breaker. Turn ON wall switch.Transmitter and receiver jumper switches do not match.Battery too weak.Set transmitter and receiver to same jumper switch set-ting.Replace with new, alkaline battery.Battery too weak. Replace with new, alkaline battery.RF interference. Turn OFF wall switch for 5 seconds, then turn back ON.Continuing RF interference. Change jumper switch settings to a different code in bothTransmitter and Receiver.© 2001 Hunter Fan CompanyFan HighFan MediumFan LowFan OFFLight KeyReverseFigure 5 - Remote OperationOperating The Remote ControlThe hand-held transmitter has individual buttons for control of the light, forcontrolling the fan speeds, for turning the fan off, and for reversing. SeeFigure 5.Pressing the “LIGHT” button will turn the light on to full brightness. Hold-ing the button will cause the light to dim slowly—release the button at thedesired brightness to hold the selected brightness level. Pushing the buttonagain will turn the light off.The fan may be started by pressing the HIGH, MEDIUM, or LOW speedbuttons. For best operation, allow the fan to start on HIGH, then select thedesired speed. Press the fan OFF button to turn the ceiling fan off. Pressthe REVERSE button to change the fan’s direction while the fan is running.NOTE: Replace 12-volt battery with type 23 A, MN-21 or equivalent.You have completed the installation of the integrated remote control. Referback to the “Installing Light Fixture” section in the Installation / Owner’sManual provided with your Hunter fan for proper instructions.4. Fan will not reverse. Fan is not running. Select a fan speed button to start fan, then press thereverse button.

Navigation menu