Husqvarna 7021Ch1 Users Manual OM, 7021 CH 1, 96143000600, 2004 10, Walk Mower

7021CH1 to the manual 4c5f8def-0838-42a2-8521-4d9ad80b1bd6

: Husqvarna Husqvarna-7021Ch1-Users-Manual-317355 husqvarna-7021ch1-users-manual-317355 husqvarna pdf

Open the PDF directly: View PDF .
Page Count: 20

7021CH1

Owner’s Manual

532 19 39-67 10.22.04 BY Printed in U.S.A.

2

WARNING: Battery posts, terminals and

related ac ces so ries contain lead and lead

compounds, chemicals known to the State

of Cal i for nia to cause can cer and birth

defects or oth er re pro duc tive harm. Wash

hands after handling.

WARNING: Engine exhaust, some of its

con stit u ents, and certain vehicle com po -

nents contain or emit chem i cals known to

the State of Cal i for nia to cause can cer and

birth defects or oth er re pro duc tive harm.

CAUTION: Always disconnect spark plug

wire and place wire where it cannot contact

spark plug in order to prevent ac ci den tal

starting when setting up, trans port ing,

adjusting or making re pairs.

Look for this symbol to point out im-

por tant safety precautions. It means

CAUTION!!! BE COME ALERT!!! YOUR

SAFE TY IS IN VOLVED.

CAUTION: Muffl er and other engine parts

become extremely hot during operation

and remain hot after engine has stopped.

To avoid severe burns on contact, stay away

from these areas.

Safe Operation Practices for Walk-Behind Mowers

IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROW ING OBJECTS. FAILURE

TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

SAFETY RULES

I. GENERAL OPERATION

• Read, understand, and follow all instructions on the

machine and in the manual(s) before starting. Be thor-

ough ly familiar with the controls and the proper use of

the machine before starting.

• Do not put hands or feet near or under rotating parts.

Keep clear of the discharge opening at all times.

• Only allow responsible individuals, who are familiar

with the instructions, to operate the machine.

• Clear the area of objects such as rocks, toys, wire,

bones, sticks, etc., which could be picked up and thrown

by the blade.

• Be sure the area is clear of other people before mow-

ing. Stop machine if anyone enters the area.

• Do not operate the mower when barefoot or wearing

open sandals. Always wear substantial foot wear.

• Do not pull mower backwards unless absolutely nec-

es sary. Always look down and behind before and while

moving backwards.

• Never direct discharged material toward anyone.

Avoid discharging material against a wall or obstruc-

tion. Material may richochet back toward the operator.

Stop the blade when crossing gravel surfaces.

• Do not operate the mower without proper guards,

plates, grass catcher or other safety protective devices

in place.

• See manufacturer’s instructions for proper operation

and installation of accessories. Only use accessories

approved by the manufacturer.

• Stop the blade(s) when crossing gravel drives, walks,

or roads.

• Stop the engine (motor) whenever you leave the equip-

ment, before cleaning the mower or unclogging the

chute.

• Shut the engine (motor) off and wait until the blade comes

to complete stop before removing grass catch er.

• Mow only in daylight or good artifi cial light.

• Do not operate the machine while under the infl uence

of alcohol or drugs.

• Never operate machine in wet grass. Always be sure of

your footing: keep a fi rm hold on the handle and walk;

never run.

• Disengage the self-propelled mechanism or drive clutch

on mowers so equipped before star ting the engine (motor).

• If the equipment should start to vibrate abnormally,

stop the engine (motor) and check immediately for the

cause. Vibration is generally a warning of trouble.

• Always wear safety goggles or safety glasses with side

shields when operating mower.

II. SLOPE OPERATION

Slopes are a major factor related to slip and fall accidents

which can result in severe injury. All slopes require extra

caution. If you feel uneasy on a slope, do not mow it.

DO:

• Mow across the face of slopes: never up and down. Exer-

cise extreme caution when changing direction on slopes.

• Remove obstacles such as rocks, tree limbs, etc.

• Watch for holes, ruts, or bumps. Tall grass can hide

obstacles.

DO NOT:

• Do not trim near drop-offs, ditches or embankments.

The operator could lose footing or balance.

• Do not trim excessively steep slopes.

• Do not mow on wet grass. Reduced footing could cause

slipping.

III. CHILDREN

Tragic accidents can occur if the operator is not alert to

the presence of children. Children are often attracted to

the machine and the mowing activity.

Never

assume that

children will remain where you last saw them.

• Keep children out of the trimming area and under the

watchful care of another re spon si ble adult.

• Be alert and turn machine off if children enter the

area.

• Before and while walking backwards, look behind and

down

for small children.

• Never allow children to operate the machine.

• Use extra care when approaching blind corners, shrubs,

trees, or other objects that may obscure vision.

IV. SAFE HANDLING OF GASOLINE

Use extreme care in handling gasoline. Gasoline is ex-

tremely fl ammable and the vapors are explosive.

• Extinguish all cigarettes, cigars, pipes and other sources

of ignition.

• Use only an approved container.

• Never remove gas cap or add fuel with the engine run-

ning. Allow engine to cool before refueling.

3

SAFETY RULES ......................................................... 2-3

PRODUCT SPECIFICATIONS....................................... 3

CUSTOMER RESPONSIBILITIES................................. 3

ASSEMBLY .................................................................... 4

OPERATION ............................................................... 5-8

MAINTENANCE SCHEDULE ........................................ 9

MAINTENANCE ........................................................ 9-11

SERVICE AND AD JUST MENTS ................................. 12

STORAGE .................................................................... 13

TROU BLE SHOOT ING ................................................. 14

REPAIR PARTS....................................................... 16-19

WARRANTY................................................................. 20

PRODUCT SPECIFICATIONS

Gasoline Capacity 1.6 Quarts

and Type: (Unleaded Regular Only)

Oil Type (API SG–SL): SAE 30 (above 32°F);

SAE 5W-30 (below 32°F)

Oil Capacity: 20 Ounces

Spark Plug (Gap: .030"): Champion RC12YC

Blade Bolt Torque: 35-40 ft. lbs. (47-54 N-m)

CONGRATULATIONS on your purchase of a new lawn

mower. It has been designed, engineered and man u fac tured

to give you the best possible dependability and performance.

Should you experience any problem you cannot easily

remedy, please contact your nearest authorized service

center/department. We have competent, well-trained

tech ni cians and the proper tools to service or repair this

lawn mower.

Please read and retain this manual. The instructions will

enable you to assemble and maintain your lawn mower

properly. Always observe the “SAFETY RULES”.

SERIAL

NUMBER: _________________________________

DATE OF PURCHASE: _______________________

THE MODEL AND SERIAL NUMBERS WILL BE FOUND

ON A DECAL ATTACHED TO THE REAR OF THE LAWN

MOWER HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND

DATE OF PURCHASE AND KEEP IN A SAFE PLACE

FOR FUTURE REFERENCE.

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.

• Follow a regular schedule in maintaining, caring for and

using your lawn mower.

• Follow the instructions under “Maintenance” and “Stor-

age” sec tions of this own er’s manual.

TABLE OF CONTENTS

• Never refuel the machine indoors.

• Never store the machine or fuel container where there

is an open fl ame, spark or pilot light such as a water

heater or on other appliances.

• Never fi ll containers inside a vehicle, on a truck or trailer

bed with a plastic liner. Always place containers on

the ground away from your vehicle before fi lling.

• Remove gas-powered equipment from the truck or trailer

and refuel it on the ground. If this is not possible, then

refuel such equipment with a portable container, rather

than from a gasoline dispenser nozzle.

• Keep the nozzle in contact with the rim of the fuel tank

or container opening at all times until fueling is complete.

Do not use a nozzle lock-open device.

• If fuel is spilled on clothing, change clothing immedi-

ately.

• Never overfi ll fuel tank. Replace gas cap and tighten

securely.

V. GENERAL SERVICE

• Never run a machine inside a closed area.

• Never make adjustments or repairs with the engine

(motor) running. Disconnect spark plug wire, and keep

wire away from plug to prevent accidental starting.

• Keep nuts and bolts, especially blade attachement

bolts, tight and keep equipment in good condition.

• Never tamper with safety devices. Check their proper

operation regularly.

• Keep machine free of grass, leaves, or other debris

build-up. Clean oil or fuel spillage. Allow machine to

cool before storing.

• Stop and inspect the equipment if you strike an object.

Repair, if necessary, before restarting.

• Never attempt to make wheel height adjustments while

the engine (motor) is running.

• Grass catcher components are subject to wear, dam-

age, and deterioration, which could expose moving

parts or allow objects to be thrown. Frequently check

com po nents and replace with manufacturer’s rec om -

mend ed parts, when necessary.

• Mower blade is sharp and can cut. Wrap the blade or

wear gloves, and use extra caution when servicing it.

• Do not change the engine governor setting or overspeed

the engine.

• Maintain or replace safety and instruction labels, as

necessary.

WARNING: This lawn mower is equipped with an internal com bus tion engine and should not be used on or near any

un im proved forest-covered, brush-covered or grass-cov ered land unless the engine’s exhaust system is equipped with

a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in

effective working order by the operator. A spark arrester for the muffl er is available through your nearest authorized

service centre.

4

ASSEMBLY

Read these instructions and this man u al in its entirety before

you attempt to assemble or operate your new lawn mow er.

IMPORTANT: THIS LAWN MOWER IS SHIPPED WITH-

OUT OIL OR GASOLINE IN THE ENGINE.

Your new lawn mower has been as sem bled at the factory

with the ex cep tion of those parts left unassembled for ship-

ping purposes. All parts such as nuts, washers, bolts, etc.,

necessary to com plete the as sem bly have been placed in

the parts bag. To ensure safe and proper operation of your

lawn mow er, all parts and hard ware you assemble must

be tightened se cure ly. Use the correct tools as nec es sary

to ensure proper tightness.

TO RE MOVE LAWN MOW ER FROM CAR TON

1. Remove loose parts included with mower.

2. Cut down two end corners of car ton and lay end panel

down fl at.

3. Remove all packing materials ex cept padding be tween

upper and lower handle and padding holding operator

presence control bar to up per handle.

4. Roll lawn mower out of carton and check carton thor-

ougly for ad di tion al loose parts.

HOW TO SET UP YOUR LAWN MOW ER

TO UNFOLD HANDLE (See Fig. 1)

IMPORTANT: UNFOLD HANDLE CAREFULLY SO AS

NOT TO PINCH OR DAMAGE CON TROL CABLES.

1. Raise handles until lower handle section locks into

place in mowing position.

2. Remove protective padding, raise upper handle sec-

tion into place on lower handle and tighten both handle

knobs.

3. Remove handle padding holding operator pres ence

control bar to upper handle.

Your handles may be adjusted for your mowing comfort.

Refer to “ADJUST HANDLE” in the Service and Ad just ments

sec tion of this man u al.

TO ASSEMBLE GRASS CATCHER

(See Fig. 2)

1. Put grass catcher frame into grass bag with rigid part

of bag on the bottom. Make sure the frame handle is

outside of the bag top.

2. Slip vinyl bindings over frame.

NOTE: If vinyl bindings are too stiff, hold them in warm water

for a few minutes. If bag gets wet, let it dry before using.

TO INSTALL ATTACHMENTS

Your lawn mower was shipped ready to be used as a

mulcher. To convert mower to bagging or discharging,

see “TO CON VERT MOWER” in the Operation section of

this man u al.

FIG. 1

OPERATOR

PRESENCE

CONTROL

BAR

HANDLE

KNOB

LIFT

UP

LIFT

UP

LOWER

HANDLE

MOWING

PO SI TION

UPPER

HANDLE

FIG. 2

FRAME

HANDLE

VINYL

BINDINGS

FRAME

OPENING

5

KNOW YOUR LAWN MOWER

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR LAWN MOWER.

Compare the illustrations with your lawn mower to familiarize yourself with the location of various controls and adjustments.

Save this manual for future reference.

MEETS CPSC SAFETY REQUIREMENTS

Our rotary walk-behind power lawn mowers conform to the safety standards of the American National Standards Institute

and the U.S. Consumer Product Safety Commission. The blade turns when the engine is running.

STARTER HANDLE – used for starting the engine.

PRIMER – pumps additional fuel from the carburetor to the

cylinder for use when starting a cold engine.

MULCHER DOOR – allows conversion to discharge or

bagging operation.

HOUSING

GRASS

CATCHER

OPERATOR PRESENCE CONTROL BAR – must be held

down to the handle to start the engine. Release to stop

the engine.

DRIVE CONTROL LEVER – used to engage power-pro-

pelled forward mo tion of lawn mower.

OPERATOR

PRESENCE

CON TROL

BAR

WHEEL

ADJUSTER

(ON EACH

WHEEL)

STARTER

HANDLE

EN GINE OIL CAP WITH DIPSTICK

HANDLE KNOB

GAS O LINE

FILL ER CAP

These symbols may appear on your lawn mower or in literature supplied with the product. Learn and understand

their meaning.

PRIMER

OPERATION

IMPORTANT: This lawn mower is shipped WITHOUT OIL OR GASOLINE in the engine.

MUFFLER

AIR FILTER

DRIVE CONTROL LEVER

DRIVE COVER

SPARK PLUG

MULCHER DOOR

6

SIDE DISCHARGING (See Fig. 6)

• Rear door must be closed.

• Open mulcher door and install dis charge defl ector

under door as shown.

• Mower is now ready for discharging operation.

• To convert to mulching or bagging operation, dis charge

defl ector must be removed and mulcher door must be

closed.

TO CONVERT MOWER

Your lawn mower was shipped ready to be used as a

mulcher. To convert to bagging or discharging:

REAR BAGGING (See Fig. 5)

• Lift rear door of the lawn mower and place the grass

catcher frame hooks onto the door pivot pins.

• To convert to mulching or dis charg ing operation, remove

grass catch er and close rear door.

FIG. 5

PIVOT PINS REAR

DOOR

GRASS

CATCHER

HANDLE

CATCH ER FRAME HOOK

HOW TO USE YOUR LAWN MOWER

ENGINE SPEED

The engine speed was set at the factory for optimum per-

formance. Speed is not adjustable.

ENGINE ZONE CONTROL

CAUTION: Federal regulations require

an engine control to be installed on this

lawn mower in order to minimize the risk

of blade contact injury. Do not un der

any cir cum stanc es attempt to defeat

the function of the operator control.

The blade turns when the engine is

running.

• Your lawn mower is equipped with an operator presence

control bar which requires the operator to be positioned

behind the lawn mower handle to start and operate the

lawn mower.

DRIVE CONTROL (See Fig. 3)

• Self-propelling is controlled by hold ing the operator

presence control bar down to the handle and push-

ing the drive control lever forward until it clicks; then

releasing the lever.

• Forward motion will stop when the operator presence

control bar is re leased. To stop forward motion without

stop ping engine, re lease the operator presence con-

trol bar slight ly until the drive control dis en gag es. Hold

op er a tor presence control bar down against handle to

con tin ue mowing without self-pro pel ling.

• To keep drive control engaged when turning corners,

push down on han dle and lift front wheels off ground

while turning lawn mower.

The operation of any lawn mower can result in foreign objects thrown into the eyes, which can result in

severe eye damage. Always wear safety glasses or eye shields while operating your lawn mower or per-

forming any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask

over spectacles.

OPERATION

FIG. 4

LEVER BACKWARD TO LOWER MOWER

LEVER FORWARD TO RAISE MOWER

PLATE

TAB

LEVER

TO ENGAGE

DRIVE CONTROL

DRIVE

CONTROL

DRIVE

CONTROL

DISENGAGED

OPERATOR PRESENCE CONTROL BAR

FIG. 3

TO ADJUST CUTTING HEIGHT (See Fig. 4)

Raise wheels for low cut and lower wheels for high cut,

adjust cutting height to suit your requirements. Me di um

position is best for most lawns.

• To change cutting height, squeeze adjuster lever to ward

wheel. Move wheel up or down to suit your re quire ments.

Be sure all wheels are in the same setting.

NOTE: Adjuster is properly positioned when plate tab inserts

into hole in lever. Also, 9-position adjusters (if so equipped)

allow lever to be positioned between the plate tabs.

7

OPERATION

SIMPLE STEPS TO REMEMBER

WHEN CONVERTING YOUR LAWN MOWER

FOR MULCHING -

1. Rear door closed. 2. Mulcher door closed.

FOR REAR BAGGING -

1. Grass catcher installed. 2. Mulcher door closed.

FOR SIDE DISCHARGING -

1. Rear door closed. 2. Discharge defl ector installed.

FIG. 6

OPEN

MULCHER

DOOR

DISCHARGE

DEFLECTOR

BEFORE STARTING ENGINE

ADD OIL (See Fig. 8)

Your lawnmower is shipped without oil in the engine. For type

and grade of oil to use, see “EN GINE” in the Maintenance

section of this manual.

CAUTION: DO NOT overfi ll engine with

oil, or it will smoke on startup.

1. Be sure lawnmower is level.

2. Remove oil dipstick from oil fi ll spout.

3. Engine holds 20 ounces of oil. For type and grade of

oil to use, see “ENGINE” in the Maintenance section

of this manual.

4. Pour oil slowly. Do not overfi ll. Wait one minute to allow

oil to settle. Insert and tighten dipstick, then remove it

to check oil level.

IMPORTANT:

• Check oil level before each use. Add oil if needed. Fill

to full line on dipstick.

• Change the oil after every 25 hours of operation or each

season. You may need to change the oil more often

under dusty, dirty conditions. See “TO CHANGE EN-

GINE OIL” in the Maintenance section of this manual.

CAUTION: Do not run your lawn mower

with out rear door closed or ap proved

grass catcher in place. Never at tempt

to op er ate the lawn mow er with the rear

door re moved or propped open.

TO EMPTY GRASS CATCHER (See Fig. 7)

1. Lift up on grass catcher using the frame han dle.

2. Remove grass catcher with clippings from under lawn

mower han dle.

3. Empty clippings from bag using both frame handle and

bag handle.

NOTE: Do not drag the bag when emptying; it will cause

unnecessary wear.

FIG. 7

FRAME

HANDLE

BAG

HANDLE

8

MOWING TIPS

CAUTION: Do not use de-thatcher blade

attachments on your mower. Such at-

tachments are hazardous, will damage

your mower and could void your warranty.

• Under certain conditions, such as very tall grass, it

may be necessary to raise the height of cut to reduce

pushing effort and to keep from overloading the engine

and leaving clumps of grass clippings. It may also be

necessary to reduce ground speed and/or run the lawn

mower over the area a second time.

• For extremely heavy cutting, reduce the width of cut

by overlapping previously cut path and mow slowly.

• For better grass bagging and most cutting conditions,

the engine speed should be set in the fast position.

• Pores in cloth grass catchers can become fi lled with

dirt and dust with use and catchers will collect less

grass. To prevent this, regularly hose catcher off with

water and let dry before using.

• Keep top of engine around starter clear and clean of

grass clippings and chaff. This will help engine air fl ow

and extend engine life.

MULCHING MOWING TIPS

IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER

HOUSING FREE OF BUILT-UP GRASS AND TRASH. SEE

“CLEANING” IN MAINTENANCE SECTION OF THIS MANUAL.

• The special mulching blade will recut the grass clip-

pings many times and reduce them in size so that as

they fall onto the lawn they will disperse into the grass

and not be noticed. Also, the mulched grass will biode-

grade quickly to provide nutrients for the lawn. Always

mulch with your highest engine (blade) speed as this

will provide the best recutting action of the blades.

• Avoid cutting your lawn when it is wet. Wet grass tends

to form clumps and interferes with the mulching action.

The best time to mow your lawn is the early afternoon.

At this time the grass has dried, yet the newly cut area

will not be exposed to direct sunlight.

• For best results, adjust the lawn mower cutting height

so that the lawn mower cuts off only the top one-third of

the grass blades (See Fig. 9). If the lawn is overgrown

it will be necessary to raise the height of cut to reduce

pushing effort and to keep from overloading the engine

and leaving clumps of mulched grass. For extremely

heavy mulching, reduce your width of cut by overlap-

ping previously cut path and mow slowly.

ADD GASOLINE (See Fig. 8)

• Fill fuel tank to bottom of tank fi ller neck. Do not over-

fi ll. Use fresh, clean, regular unleaded gasoline with

a minimum of 87 octane. Do not mix oil with gasoline.

Purchase fuel in quan ti ties that can be used within 30

days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or

fuel. Do not store, spill or use gasoline

near an open fl ame.

Alcohol blended fuels (called gasohol

or using ethanol or methanol) can at-

tract moisture which leads to separation

and for ma tion of acids during storage.

Acidic gas can damage the fuel sys-

tem of an engine while in storage. To

avoid engine problems, the fuel system

should be emptied before stor age of

30 days or longer. Empty the gas tank,

start the engine and let it run until the

fuel lines and carburetor are empty. Use

fresh fuel next season. See Storage

In struc tions for additional information.

Never use engine or carburetor cleaner

products in the fuel tank or permanent

damage may occur.

OPERATION

FIG. 9

MAX 1/3

TO STOP ENGINE

• To stop engine, release operator presence con trol bar.

NOTE: In cooler weather it may be necessary to repeat

priming steps. In warmer weather over priming may cause

fl ooding and engine will not start. If you do fl ood engine,

wait a few minutes before attempting to start and do not

repeat priming steps.

TO START ENGINE

NOTE: Due to protective coatings on the engine, a small

amount of smoke may be present during the initial use of

the product and should be considered normal.

1. To start a cold engine, push primer three (3) times

before trying to start. Use a fi rm push. This step is not

usually necessary when starting an engine which has

already run for a few minutes.

2. Hold operator presence control bar down to the han dle

and pull starter handle quickly. Do not allow starter rope

to snap back.

ENGINE

OIL CAP

GASOLINE

FILLER

CAP

PRIMER

FIG. 8

• Certain types of grass and grass conditions may require

that an area be mulched a second time to completely

hide the clippings. When doing a second cut, mow

across (perpendicular) to the fi rst cut path.

• Change your cutting pattern from week to week. Mow

north–south one week, then change to east–west the

next week. This helps prevent matting/graining of lawn.

9

Check for Loose Fasteners

Clean / Inspect Grass Catcher *

Check Tires

Check Drive Wheels ***

Clean Lawn Mower ****

Clean under Drive Cover ***

Check Drive Belt / Pulleys ***

Check / Sharpen / Replace Blade

Lubrication

Clean and Recharge Battery **

Check Engine Oil level

Change Engine Oil

Clean Air Filter

Inspect Muffler

Replace Spark Plug

Replace Air Filter Paper Cartridge

Empty fuel system or add Stabilizer

BEFORE

EACH

USE

AFTER

EACH

USE

EVERY

10

HOURS

EVERY

25 HOURS

OR SEASON

EVERY

100

HOURS

BEFORE

STORAGE

1- Change more often if operating under a heavy load or in high outdoor temperatures.

2- Service more often if operating in dirty or dusty conditions.

3- Replace blades more often when mowing in sandy soil.

4- Charge 48 hours at end of season.

5- And after each 5 hours of use.

(if so equipped)

Electric-Start mowers

Power-Propelled mowers

Use a scraper

to clean under deck

*

**

***

****

MAINTENANCE

LUBRICATION CHART

GENERAL RECOMMENDATIONS

The warranty on this lawn mower does not cover items that

have been subjected to operator abuse or negligence. To

receive full value from the warranty, operator must maintain

mower as instructed in this manual.

Some adjustments will need to be made periodically to

properly maintain your unit.

At least once a season, check to see if you should make

any of the adjustments described in the Service and Ad-

just ments section of this manual.

• At least once a year, replace the spark plug, clean or

replace air fi lter element and check blade for wear. A

new spark plug and clean/new air fi lter element assure

proper air-fuel mixture and help your engine run better

and last longer.

• Follow the maintenance schedule in this manual.

BEFORE EACH USE

1. Check engine oil level.

2. Check for loose fasteners.

LUBRICATION

Keep unit well lubricated (See “LUBRICATION CHART”).

IMPORTANT: DO NOT OIL OR GREASE PLASTIC WHEEL

BEARINGS. VISCOUS LU BRI CANTS WILL ATTRACT DUST

AND DIRT THAT WILL SHORT EN THE LIFE OF THE SELF-

LU BRI CAT ING BEARINGS. IF YOU FEEL THEY MUST BE

LU BRI CATED, USE ONLY A DRY, POW DERED GRAPHITE

TYPE LUBRICANT SPAR INGLY.

➀ SPRAY LUBRICANT

➁ SEE “ENGINE” IN MAINTENANCE SECTION

➁ ENGINE OIL

➀ HANDLE BRACK ET MOUNT ING PINS

➀ REAR DOOR HINGE

➀ MULCHER

DOOR

HINGE PIN

➀ WHEEL

ADJUSTER

(ON EACH

WHEEL)

10

LAWN MOWER

Always observe safety rules when performing main te nance.

TIRES

• Keep tires free of gasoline, oil, or insect control chem-

i cals which can harm rubber.

• Avoid stumps, stones, deep ruts, sharp objects and

other hazards that may cause tire damage.

DRIVE WHEELS

Check front drive wheels each time be fore you mow to be

sure they move freely.

The wheels not turning freely means trash, grass cuttings,

etc. are in the drive wheel area and must be cleaned to

free drive wheels.

If necessary to clean the drive wheels, be sure to clean

both front wheels.

1. Remove hubcaps, locknuts and washers.

2. Remove wheels from wheel ad just ers.

3. Remove any trash or grass cuttings from inside the

dust cover, pinion and/or drive wheel gear teeth.

4. Put wheels back in place.

NOTE: If after cleaning, the drive wheels do not turn freely,

contact a qualifi ed service center.

BLADE CARE

For best results, mower blade must be kept sharp. Re place

a bent or dam aged blade.

CAUTION: Use only a replacement blade

approved by the manufacturer of your

mower. Using a blade not approved

by the manufacturer of your mower is

hazardous, could damage your mower

and void your warranty.

TO REMOVE BLADE (See Fig. 10)

1. Disconnect spark plug wire from spark plug and place

wire where it cannot come in contact with plug.

2. Turn lawn mower on its side. Make sure air fi lter and

carburetor are up.

3. Use a wood block between blade and mower hous ing

to prevent blade from turning when re mov ing blade bolt.

NOTE: Protect your hands with gloves and/or wrap blade

with heavy cloth.

4. Remove blade bolt by turning counter-clockwise.

5. Remove blade and attaching hardware (bolt, lock wash er

and hardened wash er).

NOTE: Remove the blade adapter and check the key inside

hub of blade adapter. The key must be in good condition to

work properly. Replace adapter if dam aged.

TO REPLACE BLADE (See Fig. 10)

1. Position the blade adapter on the engine crank shaft.

Be sure key in adapter and crankshaft key way are

aligned.

2. Position the blade on the blade adapter aligning the

two (2) holes in the blade with the raised lugs on the

adapter.

MAINTENANCE

3. Be sure the trailing edge of blade (opposite sharp edge)

is up toward the engine.

4. Install the blade bolt with the lock washer and hard ened

washer into blade adapter and crank shaft.

5. Use block of wood between blade and lawn mower

housing and tighten the blade bolt, turning clock wise.

• The recommended tightening torque is 35-40 ft. lbs.

IMPORTANT: BLADE BOLT IS HEAT TREATED. IF BOLT NEEDS

REPLACING, REPLACE ONLY WITH APPROVED BOLT SHOWN

IN THE REPAIR PARTS SECTION OF THIS MANUAL.

TO SHARPEN BLADE

NOTE: We do not recommend sharp en ing blade - but if

you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An

un bal anced blade will cause eventual damage to lawn

mower or engine.

• The blade can be sharp ened with a fi le or on a grinding

wheel. Do not attempt to sharpen while on the mower.

• To check blade balance, drive a nail into a beam or

wall. Leave about one inch of the straight nail ex posed.

Place center hole of blade over the head of the nail.

If blade is balanced, it should remain in a horizontal

position. If either end of the blade moves downward,

sharpen the heavy end until the blade is balanced.

GEAR CASE

• To keep your drive system working properly, the gear

case and area around the drive should be kept clean

and free of trash build-up. Clean under the drive cover

twice a season.

• The gear case is fi lled with lubricant to the proper

level at the factory. The only time the lubricant needs

attention is if service has been performed on the gear

case.

• If lubricant is required, use only ELF Multis EP00. Do

not sub sti tute.

GRASS CATCHER

• The grass catcher may be hosed with water, but must

be dry when used.

• Check your grass catcher often for damage or de te -

ri o ra tion. Through normal use it will wear. If catcher

needs replacing, replace only with ap proved replace-

ment catcher shown in the Repair Parts section of this

manual. Give the mower model number when ordering.

FIG. 10

BLADE

BOLT

HARDENED

WASHER

LOCK

WASHER

BLADE ADAPTER KEY

BLADE

TRAILING EDGE

CRANKSHAFT

KEY WAY

CRANKSHAFT

11

AIR FILTER (See Fig. 12)

Your engine will not run properly using a dirty air fi lter.

Replace paper cartridge every 100 hours of operation or

every season, which ev er occurs fi rst. Service air cleaner

more often under dusty conditions.

1. Loosen screws and remove cover.

2. Carefully remove cartridge.

3. Clean by gently tapping on a fl at surface. If very dirty,

replace cartridge.

CAUTION: Petroleum solvents, such as

ker o sene, are not to be used to clean

car tridge . They may cause de te ri o ra tion

of the cartridge. Do not oil car tridge.

Do not use pres sur ized air to clean or

dry car tridge.

4. Install cartridge, then replace cover.

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

SAE VISCOSITY GRADES

-20 0 30 40 80 100

-30 -20 0 20 30 40

F

C

32

-10 10

60

5W-30

SAE 30

MAINTENANCE

FIG. 11

CONTAINER

ENGINE

LUBRICATION

Use only high quality detergent oil rated with API service

classifi cation SG–SL. Select the oil's SAE viscosity grade

according to your expected operating temperature.

NOTE: Multi-viscosity oils (5W30, 10W30 etc.) improve

starting in cold weather, and you should check your engine

oil level frequently to avoid possible engine damage from

running low on oil.

Change the oil after every 25 hours of operation or at least

once a year if the lawn mower is not used for 25 hours in

one year.

Check the crankcase oil level before starting the engine

and after each fi ve (5) hours of continuous use. Tighten oil

plug securely each time you check the oil level.

TO CHANGE ENGINE OIL (See Fig. 11)

NOTE: Before tipping lawn mower to drain oil, empty fuel

tank by running engine until fuel tank is empty.

1. Disconnect spark plug wire from spark plug and place

wire where it cannot come in contact with plug.

2. Remove engine oil cap; lay aside on a clean surface.

3. Tip lawn mower on its side as shown and drain oil into

a suitable container. Rock lawn mower back and forth

to remove any oil trapped inside of engine.

CARTRIDIGE

COVER

SCREWS

BASE

FIG. 12

4. Wipe off any spilled oil from mower or side of engine.

5. Slowly pour oil down the oil fi ll spout, stopping every

few ounces to check the oil level with the dipstick.

6. Stop adding oil when you reach the FULL mark on the

dipstick. Wait a minute to allow oil to settle.

7. Continue adding small amounts of oil, rechecking the

dipstick until oil level settles at FULL. DO NOT over-

fi ll, or engine will smoke heavily from the muffl er on

startup.

8. Always be sure to retighten oil dipstick before starting

engine.

9. Re con nect spark plug wire to spark plug.

MUFFLER

Inspect and replace corroded muffl er as it could create a

fi re hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each mowing season

or after every 100 hours of operation, whichever occurs

fi rst. Spark plug type and gap setting are shown in the

“PROD UCT SPEC I FI CA TIONS” section of this manual.

CLEANING

IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER

HOUSING FREE OF BUILT-UP GRASS AND TRASH. CLEAN

THE UNDERSIDE OF YOUR MOWER AFTER EACH USE.

CAUTION: Disconnect spark plug wire

from spark plug and place wire where it

cannot come in contact with plug.

• Clean the underside of your lawn mower by scraping

to remove build-up of grass and trash.

• Clean engine often to keep trash from accumulating. A

clogged engine runs hotter and shortens engine life.

• Keep fi nished surfaces/wheels free of gasoline, oil, etc.

• We do not recommend using a garden hose to clean

lawn mower unless the electrical system, muffl er, air

fi lter and carburetor are covered to keep water out.

Water in engine can result in shortened engine life.

CLEAN UNDER DRIVE COVER

Clean under drive cover at least twice a season. Scrape un-

derside of cover with putty knife or similar tool to remove any

build-up of trash or grass on underside of drive cover.

12

MOWING

POSITION

MOWING

POSITION

HIGH POSITIONLOW POSITION

HANDLE

BRACKET

HAIRPIN

COTTER

MOUNTING

PIN

FIG. 15

LAWN MOWER

TO ADJUST CUTTING HEIGHT

See “TO ADJUST CUTTING HEIGHT” in the Operation

section of this manual.

REAR DEFLECTOR

The rear defl ector, attached between the rear wheels of

your mower, is provided to minimize the possibility that

objects will be thrown out of the rear of the mower into

the operator's mowing position. If the defl ector becomes

damaged, it should be replaced.

TO REMOVE DRIVE BELT (See Fig. 13)

1. Remove drive cover. Remove belt from gearcase pulley

by push ing down on pulley and rolling belt off it.

2. Turn mower on its side (air fi lter and car bu re tor up).

3. Remove blade.

4. Remove debris shield.

5. Remove belt from engine pulley on crankshaft.

Replace drive belt by reversing above steps.

NOTE: Always use factory approved belt to assure fi t and

long life.

CAUTION: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

1. Release control bar and stop engine.

2. Make sure the blade and all moving parts have completely stopped.

3. Disconnect spark plug wire from spark plug and place where it cannot come in contact with plug.

ENGINE

ENGINE SPEED

Your engine speed has been factory set. Do not attempt to

increase engine speed or it may result in personal injury. If

you believe that the engine is running too fast or too slow,

take your lawn mower to an authorized service center for

repair and adjustment.

CARBURETOR

Your carburetor is not adjustable. If your engine does not

operate properly due to suspected carburetor problems,

take your lawn mower to an authorized service center for

repair and/or adjustment.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR,

WHICH IS FACTORY SET FOR PROPER ENGINE SPEED.

OVER SPEED ING THE ENGINE ABOVE THE FACTORY HIGH

SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE

ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING,

CONTACT YOUR NEAREST AUTHORIZED SER VICE CEN TER,

WHICH HAS PROPER EQUIP MENT AND EXPERIENCE TO

MAKE ANY NEC ES SARY ADJUSTMENTS.

SERVICE AND ADJUSTMENTS

FIG. 14

LOWER HANDLE

HANDLE

BRACKET

HAIRPIN

COTTER

SQUEEZE

TO ADJUST

MOUNTING PIN

LOWER

HANDLE

ROTATE

FIG. 16

TO ADJUST HANDLE (See Figs. 14 thru 16)

The handle can be mounted in a high or low position. The

mounting holes in the bottom of lower handle are off center

for raising or lowering the handle.

1. Remove upper handle and all wire tie(s) securing

cable(s) to lower handle.

2. Remove hairpin cotters from lower handle bracket

mount ing pin.

3. Squeeze lower handle in to remove from mounting pins.

4. Turn lower handle over to raise or lower handle.

5. Squeeze lower handle in and po si tion holes onto

mount ing pins on handle bracket.

6. Reassemble upper handle and all parts removed from

lower handle.

BELTDRIVE

COVER

PUSH DOWN

FIG. 13

13

LAWN MOWER

When lawn mower is to be stored for a period of time, clean

it thoroughly, remove all dirt, grease, leaves, etc. Store in

a clean, dry area.

1. Clean entire lawn mower (See “CLEANING” in the

Maintenance section of this manual).

2. Lubricate as shown in Maintenance section of this manual.

3. Be sure that all nuts, bolts, screws, and pins are se-

curely fastened. Inspect moving parts for damage,

breakage and wear. Replace if necessary.

4. Touch up all rusted or chipped paint surfaces; sand

lightly before painting.

HANDLE (See Figs. 17 and 18)

You can fold your lawn mower handle for storage.

1. Squeeze the bottom ends of the lower handle toward

each other until the lower handle clears the handle

bracket, then move handle forward.

2. Loosen upper handle mounting bolts enough to allow

upper handle to be folded back.

IMPORTANT: WHEN FOLDING THE HANDLE FOR STORAGE

OR TRANSPORTATION, BE SURE TO FOLD THE HANDLE AS

SHOWN OR YOU MAY DAMAGE THE CONTROL CABLES.

• When setting up your handle from the storage position, the

lower han dle will automatically lock into mow ing position.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS

FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH

AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK

DURING STORAGE. ALCOHOL BLENDED FUELS (CALLED

GASOHOL OR USING ETHANOL OR METHANOL) CAN

ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND

FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS

CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE

IN STORAGE.

• Empty the fuel tank by starting the engine and letting

it run until the fuel lines and carburetor are empty.

• Never use engine or carburetor cleaner products in the

fuel tank or permanent damage may occur.

• Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini-

mizing the formation of fuel gum deposits during stor age.

Add stabilizer to gasoline in fuel tank or storage container.

Always follow the mix ratio found on stabilizer container.

Run engine at least 10 minutes after adding stabilizer to

allow the stabilizer to reach the carburetor. Do not empty

the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en-

gine oil. (See “ENGINE” in the Maintenance section of

this manual).

CYLINDER

1. Remove spark plug.

2. Pour one ounce (29 ml) of oil through spark plug hole

into cylinder.

3. Pull starter handle slowly a few times to distribute oil.

4. Replace with new spark plug.

OTHER

• Do not store gasoline from one season to another.

• Replace your gasoline can if your can starts to rust.

Rust and/or dirt in your gasoline will cause problems.

• If possible, store your unit indoors and cover it to give

protection from dust and dirt.

• Cover your unit with a suitable protective cover that

does not retain moisture. Do not use plastic. Plastic

cannot breathe, which allows condensation to form and

will cause your unit to rust.

IMPORTANT: NEVER COVER MOWER WHILE ENGINE AND

EXHAUST AREAS ARE STILL WARM.

CAUTION: Never store the lawn mower

with gasoline in the tank inside a build-

ing where fumes may reach an open

fl ame or spark. Allow the engine to cool

before storing in any enclosure.

STORAGE

Immediately prepare your lawn mower for storage at the end of the season or if the unit will not be used for 30 days or more.

FIG. 17

LOWER HANDLE

SQUEEZE

TO ADJUST

FIG. 18

MOWING

POSITION

OPERATOR

PRES ENCE

CONTROL

BAR

FOLD

FORWARD

FOR

STORAGE

LOWER

HANDLE

HANDLE

KNOB

UPPER

HANDLE

14

Does not start 1. Dirty air fi lter. 1. Clean/replace air fi lter.

2. Out of fuel. 2. Fill fuel tank.

3. Stale fuel. 3. Empty fuel tank and refi ll tank with fresh,

clean gasoline.

4. Water in fuel. 4. Empty fuel tank and refi ll tank with fresh,

clean gasoline.

5. Spark plug wire is disconnected. 5. Connect wire to plug.

6. Bad spark plug. 6. Replace spark plug.

7. Loose blade or broken blade adapter. 7. Tight en blade bolt or replace blade adapter.

8. Control bar in released position. 8. Depress control bar to handle.

9. Control bar defective. 9. Replace control bar.

10. Fuel valve lever (if equipped) in OFF position. 10. Turn fuel valve lever to the ON position.

11. Weak battery (if equipped). 11. Charge battery.

12. Disconnected battery connector (if equipped). 12. Connect battery to engine.

Loss of power 1. Rear of lawn mower housing or cutting 1. Raise cutting height.

blade dragging in heavy grass.

2. Cutting too much grass. 2. Raise cutting height.

3. Dirty air fi lter. 3. Clean/replace air fi lter.

4. Buildup of grass, leaves and trash under 4. Clean underside of mower housing.

mower.

5. Too much oil in engine. 5. Check oil level.

6. Walking speed too fast. 6. Cut at slower walking speed.

Poor cut – 1. Worn, bent or loose blade. 1. Replace blade. Tighten blade bolt.

uneven 2. Wheel heights uneven. 2. Set all wheels at same height.

3. Buildup of grass, leaves and trash under 3. Clean underside of mower housing.

mower.

Excessive 1. Worn, bent or loose blade. 1. Replace blade. Tighten blade bolt.

vibration 2. Bent engine crankshaft. 2. Contact a qualifi ed service center.

Starter rope 1. Engine fl ywheel brake is on when control 1. Depress control bar to upper handle before

hard to pull bar is released. pulling starter rope.

2. Bent engine crankshaft. 2. Contact a qualifi ed service center.

3. Blade adapter broken. 3. Replace blade adapter.

4. Blade dragging in grass. 4. Move lawn mower to cut grass or other

hard surface before starting.

Grass catcher 1. Cutting height too low. 1. Raise cutting height.

not fi lling 2. Lift on blade worn off. 2. Replace blade.

(if so equipped) 3. Catcher not venting air. 3. Clean grass catcher.

Hard to push 1. Grass is too high or wheel height is too low. 1. Raise cutting height.

2. Rear of lawn mower housing or cutting 2. Raise rear of lawn mower housing one (1)

blade dragging in heavy grass. setting higher.

3. Grass catcher too full. 3. Empty grass catcher.

4. Handle height position not right for you. 4. Adjust handle height to suit.

Loss of drive 1. Belt wear. 1. Check/replace drive belt.

or slowing of 2. Belt off of pulley. 2. Check/reinstall drive belt.

drive speed 3. Drive cable worn or broken. 3. Replace drive cable.

PROBLEM CAUSE CORRECTION

TROUBLESHOOTING POINTS

15

SERVICE NOTES

16

ROTARY LAWN MOWER - - MODEL NUMBER 7021CH1 (96143000600) - PRODUCT NUMBER 961 43 00-06

17

ROTARY LAWN MOWER - - MODEL NUMBER 7021CH1 (96143000600) - PRODUCT NUMBER 961 43 00-06

1 532 19 25-18 Upper Handle

2 532 15 34-18 Lower Handle

3 532 18 55-78 Control Bar

4 532 18 27-55 Engine Zone Control Cable

5 532 19 15-74 Handle Bolt

6 532 19 18-56 Handle Knob

7 532 05 17-93 Hairpin Cotter

8 532 06 64-26 Wire Tie

9 532 18 04-79 Kit, Rear Door (Includes Key #16 and 17)

10 532 12 84-15 Pop Rivet

11 532 18 25-38 Support Bracket, LH

12 532 18 25-39 Support Bracket, RH

13 817 06 04-10 Screw 1/4-20 x 5/8

14 532 18 25-43 Handle Bracket Assembly, LH

15 532 18 25-45 Handle Bracket Assembly, RH

16 532 18 00-71 Spring, Rear Door, LH

17 532 18 00-72 Spring, Rear Door, RH

18 532 13 20-04 Nut, Hex

19 532 17 95-85 Rope Guide

20 532 18 90-05 Rear Skirt

21 532 08 86-52 Hinge Screw 1/4-20 x 1-1/4

24 - - - Engine, Briggs & Stratton, Model Number 12H602

(For engine service and replacement parts,

call Briggs & Stratton at 1-800-233-3723)

25 532 15 04-06 Screw, Hex Head, Threaded, Rolled 3/8-16 x 1-1/8

26 532 08 39-23 Nut, Hex, Flanged

27 532 18 55-72 Wheel Assembly, Rear

28 532 16 08-28 Shoulder Bolt 5/16-18 x .33

30 532 18 25-41 Axle Arm Assembly, Rear, RH

31 532 18 55-75 Selector Knob

32 532 18 25-37 Selector Spring

33 873 80 05-00 Locknut

34 532 18 25-42 Axle Arm Assembly, Rear, LH

35 532 19 18-53 Hubcap

36 532 18 41-93 Bolt

37 532 15 00-78 Thread Cutting Screw w/Sems 5/16-18 x 3/4

38 819 11 22-06 Washer

41 532 19 23-25 Screw, Debris Shield

43 532 18 87-84 Debris Shield

44 532 18 55-83 Kit, Lawn Mower Housing

(Includes Key Numbers 10, 11, 12 and 45)

45 532 10 73-39 Danger Decal

46 532 18 91-79 Blade Adapter / Pulley

47 532 18 90-28 Blade, 21"

48 532 85 10-74 Hardened Washer

49 532 85 02-63 Helical Washer 3/8

50 532 85 10-84 Hex Head Machine Screw 3/8-24 x 1-3/8 Grade 8

59 532 18 55-82 Discharge Defl ector

60 532 17 57-35 Hinge Bracket Assembly

61 532 17 52-85 Spring

62 532 17 56-50 Rod, Hinge

63 873 80 04-00 Locknut, Hex

64 532 18 55-76 Mulcher Door

65 532 18 81-52 O-Ring

66 532 08 83-48 Washer, Flat 3/8

- - 532 16 23-00 Warning Decal (not shown)

- - 532 19 36-97 Owner’s Manual, English/French

NOTE: All component dimensions given in U.S. inches.

1 inch = 25.4 mm

KEY PART

NO. NO. DESCRIPTION

KEY PART

NO. NO. DESCRIPTION

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty.

18

ROTARY LAWN MOWER - - MODEL NUMBER 7021CH1 (96143000600) - PRODUCT NUMBER 961 43 00-06

19

ROTARY LAWN MOWER - - MODEL NUMBER 7021CH1 (96143000600) - PRODUCT NUMBER 961 43 00-06

1 532 18 45-88 Drive Control Assembly

2 532 08 80-58 Bearing, Wheel Adjuster

3 532 17 52-62 Pan Head Tapping Screw #10-24 x 2-3/4

4 532 15 87-55 Screw

5 532 17 54-36 V-Belt

6 532 15 04-95 Retainer, Spring

7 532 19 17-30 Nut, Hex, Flanged 1/4-20

8 532 18 06-26 Hubcap

9 532 14 52-12 Locknut

11 532 18 07-67 Wheel & Tire Assembly

12 812 00 00-58 E-Ring

13 532 13 70-54 Pinion

14 532 18 94-03 Dust Cover

16 532 06 77-25 Washer 1/2

18 532 18 55-74 Selector Knob

28 532 18 55-79 Drive Cover

31 532 13 20-10 Hex Flange Nut

32 532 18 94-07 Pulley, Drive

35 532 15 15-21 Kit, Wheel Adjuster, LH

(Includes Knob and Bearing)

36 532 18 01-84 Gear Case Assembly, Complete

38 873 80 04-00 Locknut 1/4-20

40 532 13 70-90 Spring, Tension

41 532 15 15-20 Kit, Wheel Adjuster, RH

(Includes Knob and Bearing)

54 532 19 47-24 Grassbag Assembly

55 532 17 57-39 Driveshaft Cover

57 532 18 88-15 Frame, Grassbag

60 532 18 34-97 * Case, Lower

61 532 18 34-98 * Case, Upper

62 532 18 34-99 Gear, 27 Teeth

63 532 18 35-00 Lever, Clutch

64 532 18 35-01 Spring, Return

65 532 18 35-02 Shaft, Input

66 532 18 35-03 Dog, Movable

67 532 18 35-04 Dog, Fixed

68 532 18 35-05 Wire, Formed

69 532 18 35-06 Bearing, Ball

70 532 18 35-07 Fork, Shift

71 532 18 35-08 Seal, Output Shaft

72 532 18 35-09 Washer

73 532 18 35-10 Seal, Case

74 532 18 35-11 Bushing

75 532 18 35-12 Shaft, Output

76 532 18 35-13 Screw

77 532 18 35-14 Seal, Input Shaft

* Use Dow Corning #709 to reseal Gear Case Halves.

NOTE: All component dimensions given in U.S. inches.

1 inch = 25.4 mm

KEY PART

NO. NO. DESCRIPTION

KEY PART

NO. NO. DESCRIPTION

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty.

20

SECTION 1: LIMITED WARRANTY

Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original pur-

chaser to be free from defects in material and workmanship from the date of purchase for the “Warranty

Period” of the product as set forth below:

Lifetime Warranty: All tiller tines against breakage, trimmer shafts, ignition coils and modules on hand

held prod uct.

3 Year Warranty: Spindles (on Zero Turn Riders and Commercial Walk-Behinds)

2 Year COMMERCIAL-Warranty: Husqvarna Commercial Turf Equipment—zero turn riders, wide area

walks, and ground engaging commercial equipment.

2 Year NON-COMMERCIAL Warranty: Automatic Mower, Riding lawn mowers, yard and garden tractors,

walk behind mowers, tillers, chain saws, trimmers, brushcutters, clearing saws, snow blowers, handheld

blowers, backpack blowers, hedge trimmers, electrical products and power-assist collection systems for

non com mer cial, nonprofessional, noninstitutional or nonincome producing use, except as herein stated.

Emission control system components necessary to comply with CARB-TIER-II and EPA regulations,

except for those components which are part of engine systems manufactured by third party engine manu-

facturers for which the purchaser has received a separate warranty with product information supplied at

time of purchase.

1 Year Warranty: Power cutters, stump grinder, pole pruners and pole saws for non-commercial, non-pro-

fessional, non-institutional or non-income producing use. All trimmers, brushcutters, clearing saws, hover-

ing trimmers, stick edgers, backpack blowers, hand held blowers, hedge trimmers, power-assist collection

systems used for commercial, institutional, professional or income producing purposes or use.

Batteries have a one-year prorated limited warranty with 100% replacement during the fi rst 6 months.

90 Day Warranty: Automatic Mower, Chain saws, power cutters, stump grinders, pole saws, pole prun-

ers, snow throwers, model series 580 & 600 walk-behind mowers and commercial turf equipment or any

Husqvarna product used for commercial, institutional, professional, or income producing purposes or use

except as otherwise provided herein.

Husqvarna Safety Apparel carries a 90-day warranty from the date of the customer’s original purchase

for defects in material and workmanship. Normal wear, tear or abuse is not covered under warranty. Prod-

uct must be returned to Charlotte with a warranty claim form. All care and maintenance instructions must

be followed as stated by the manufacturer on the care label. The fi t of the protective apparel/boot is not

covered under warranty.

30 Day Warranty: Replacement parts, accessories including bars and chains, tools and display items.

SECTION 2: HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY

Husqvarna will repair or replace defective components without charge for parts or labor if a component

fails because of a defect in material or workmanship during the warranty period.

SECTION 3: ITEMS NOT COVERED BY THIS WARRANTY

The following items are not covered by this warranty:

(1)Normal customer maintenance items which become worn through normal regular use, including, but

not limited to, belts, blades, blade adapters, bulbs, fi lters, guide bars, lubricants, rewind springs, saw

chain, spark plugs, starter ropes and tines;

(2)Natural discoloration of material due to ultraviolet light;

(3)Engine and drive systems not manufactured by Husqvarna; these items are covered by the respective

manufacturer’s warranty as provided in writing with the product information supplied at the time of pur-

chase; all claims must be sent to the appropriate manufacturer;

(4)Lawn and garden attachments are covered by a third party which gives a warranty, all claims for war-

ranty should be sent to the manufacturer; and

(5)Emission Control System components necessary to comply with CARB-TIER-II and EPA regulations

which are manufactured by third party engine manufacturer.

SECTION 4: EXCEPTIONS AND LIMITATIONS

This warranty shall be inapplicable to defects resulting from the following:

(1)Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust,

corrosion, or any adverse reaction due to incorrect storage or use habits;

(2)Failure to operate or maintain the unit in accordance with the Owner’s/Operator’s manual or instruc-

tion sheet furnished by Husqvarna;

(3)Alterations or modifi cations that change the intended use of the product or affects the product’s per-

formance, operation, safety, or durability, or causes the product to fail to comply with any applicable

laws; or:

(4)Additional damage to parts or components due to continued use occurring after any of the above.

REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF

THE PUR CHAS

ER. HUSQVARNA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THESE PRODUCTS EXCEPT

TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABIL-

ITY OR FITNESS FOR A PARTICULAR PURPOSE ON THESE PRODUCTS IS LIMITED IN DURATION TO

THE WARRANTY PERIOD AS DEFINED IN THE LIMITED WARRANTY STATEMENT. HUSQVARNA RE-

SERVES THE RIGHT TO CHANGE OR IMPROVE THE DESIGN OF THE PRODUCT WITHOUT NO TICE,

AND DOES NOT ASSUME OBLIGATION TO UPDATE PREVIOUSLY MANUFACTURED PROD UCTS.

Some states do not allow the exclusion of incidental or consequential damages, or limitations on how long

an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives

you specifi c legal rights, and you may also have other rights which vary from state to state.

SECTION 5: CUSTOMER RESPONSIBILITIES

The product must exhibit reasonable care, maintenance, operation, storage and general upkeep as written

in the maintenance section of the Owner’s/Operator’s manual. Should an operational problem or failure occur,

the product should not be used, but delivered as is to an authorized Husqvarna dealer for evaluation. Proof

of purchase, as explained in section 6, rests solely with the customer.

SECTION 6: PROCEDURE TO OBTAIN WARRANTY CONSIDERATION

It is the Owner’s and Dealer’s responsibility to make certain that the Warranty Registration Card is properly

fi lled out and mailed to Husqvarna Forest & Garden Company. This card should be mailed within ten (10) days

from the date of purchase in order to confi rm the warranty and to facilitate post-sale service.

Proof of purchase must be presented to the authorized Husqvarna dealer in order to obtain warranty ser-

vice. This proof must include date purchased, model number, serial number, and complete name and address

of the selling dealer.

To obtain the benefi t of this warranty, the product believed to be defective must be delivered to an au-

thorized Husqvarna dealer in a timely manner, no later than thirty (30) days from date of the operational

problem or failure. The product must be delivered at the owner’s expense. Pick-up and delivery charges are

not covered by this warranty. An authorized Husqvarna dealer can be normally located through the “Yellow

Pages” of the local telephone directory or by calling 1-800-HUSKY62 for a dealer in your area.

HUSQVARNA

7349 Statesville Road

Charlotte, NC 28269

531 83 81-23 2002

WARRANTY STATEMENT