Husqvarna 966043502 Users Manual OM, 70 LP Broadcast Spreader, 966043502, 2009 02, Accessory

70 LP HUSO2009_USen_O0907001_

70 LP to the manual 7da85e74-26e1-4f68-9580-a503a4180cfc

2015-01-24

: Husqvarna Husqvarna-966043502-Users-Manual-317997 husqvarna-966043502-users-manual-317997 husqvarna pdf

Open the PDF directly: View PDF PDF.
Page Count: 8

DownloadHusqvarna Husqvarna-966043502-Users-Manual- OM, 70 LP Broadcast Spreader, 966043502, 2009-02, Accessory  Husqvarna-966043502-users-manual
Open PDF In BrowserView PDF
MODEL 70 LP

OWNER’S MANUAL

ASSEMBLY
1/4-20 x 2 1/4”
Hex Bolt

RH. Handle
Brace

1. Remove components from carton
and place spreader upside down on a
padded surface. Install LH. & RH. handle
braces to frame as shown using four (4)
1/4-20 x 2 1/4” hex bolts and nuts but do
not tighten.

1/4-20
Hex Nut

3/16 Dia x 2”
Cotter Pin
LH. Handle
Brace
Drive Wheel
1/8 Dia x 1 1/4”
Cotter Pin

2. Slide wheels onto end of axle with
the hub facing toward frame. Wheels are
identical to ease assembly. Align the
hole in the wheel hub and the hole in the
axle as shown. Secure drive wheel to
axle with 3/16 dia. x 2” cotter pin. Insert
1/8 dia. x 1 1/4” cotter pin in the hole
near the end of axle to retain free
turning wheel.

Free Turning
Wheel

#10 x 3/4
Sheet Metal
Screw

Clamp
Bracket

3. Turn spreader upright. For ease of

DOT

Handle
Assembly

assembly, make sure ON/OFF cable is on
top of handle braces. With DOT on the
handle assembly facing as shown, secure
clamp bracket using a #10 x 3/4 slotted
sheet metal screw. Install end of handle
assembly between handle braces and
secure with (2) 1/4-20 x 1 1/2” hex bolts
and nuts.

1/4-20
Hex Nut

ON/OFF Cable

2

1/4-20 x 1 1/2”
Hex Bolt

4. Attach ON/OFF control to the upper

Handle Grip

handle using (2) #10 x 3/4” slotted
sheet metal screws. Slide handle grips
onto the handle cross tube. Soapy
water will ease installation. (Do not use
petroleum based products).

ON/OFF Control

Clamp
Bracket

ON/OFF Cable
#10 x 3/4”
Sheet Metal Screws

Clamp

5. Secure On/Off cable to the clamp
bracket using the cable clamp and
#10-24 x 5/8” screw and locknut as
shown but do not tighten. Place On/
Off control in the “ON” position and
set the rate retting dial to the
“WASH” position. Pull cable away
from hopper sliding it in the cable
clamp until the shut off plate stops
against the rate setting dial. Tighten
cable clamp securely. To check
spreader for complete shutoff, pull
the On/Off control lever back to the
“OFF” position. Check to make sure
hole in the hopper is completely
closed. If not, loosen the cable
clamp and slide the cable forward
until the hole in hopper is closed.
Re-tighten bolt and check shutoff.

#10-24 x 5/8”
Screw & Locknut

ON

Shut Off
Plate

Rate Setting
Dial

Screen
Screen Clips

6. Insert screen into hopper by sliding
it under the screen clips.

3

OPERATION
1. Check the product package for the rate
setting, and recommended swath width. Turn
the spreader off by pulling the lever to the
“OFF” position as shown.

OFF

2. The rate setting is adjusted by rotating the
rate cam to the desired setting. The rate cam
locks at each setting.

3. Always fill the spreader on the driveway or
sidewalk-not on the lawn. Make sure spreader is
in the “OFF” position. Empty after each use.

4. Start spreader moving, then open spreader
by moving the lever to the “ON” position.
Always push spreader, never pull. Pull the lever
to the “OFF position to close spreader.

5. Hold handle so top of spreader is level. Tipping
the spreader too far can cause uneven spreading.

SPREAD
SWATH
APPROX. 8 to
14 FEET ON
CENTER

6. The settings and swath widths on the product
label are recommended starting points. Always
check the delivery rate and pattern on a small area
before treating a large area. Actual delivery rate
can vary due to weather conditions, operating
variables, and condition of the product being
applied. See “HOW TO DETERMINE SPREADER
SETTING AND SWATH WIDTH” for details.

8. Empty spreader after each use. Return

7. Push spreader 2 1/2 m.p.h. (18 feet in 5
seconds) for full 8’ to 14’ spread pattern when
applying fertilizer products. Apply header strips
at each end of area to be treated then space
trips across the area as shown.
4

leftover material to its original container.

HOW TO DETERMINE SPREADER
SETTINGS AND SPREAD WIDTH
Two major factors should be considered when determining correct spreader settings of any
product:
1. The product application rate, or the amount of material applied per 1,000 square feet.
2. The effective pattern width, or the actual width in which material is applied. Label settings
are a guide and can be affected by numerous factors.

EFFECTIVE PATTERN WIDTH
A simple visual pattern test can be
made by operating the spreader over a
non-turf area and evaluating the pattern.
A more accurate method is to place a
row of common, disposable, aluminum
cake pans approximately 1 foot on
centers. Set the rate cam at a middle
setting and make 3 or 4 passes in the
same direction as shown. Pour the
material collected from each pan into
individual bottles of the same size. Set
them side by side in order, and visually
inspect their volume. The effective
pattern width is the distance out from
the spreader to a point where the
amount of material is 1/2 the average
amount in the center pans. This
distance is multiplied by 2 to achieve
the total effective pattern width.

APPLICATION RATE
Knowing the effective pattern width (for example,
10 feet), measure a distance equal to 100 square
feet (10’ x 10’ area covered). Determine the
product coverage is pounds/ 100 sq. ft. by taking
the weight of the product and dividing it by the
recommended square foot coverage (add two
zeroes to the weight of the bag).
EXAMPLE: Product weight: 25 lbs.
sq. ft. coverage: 5,000 sq. ft.
2500 lbs. - 5,000 sq. ft.
= .5 lbs. / 100 sq. ft.

5

Weigh out between 15 to 20 lbs. of
material and spread over the 100 sq. ft.
area. Weigh remaining material left in
hopper and adjust rate setting as
required. Repeat test until application
rate is correct.

RATE SETTING CONVERSION
70 LPsettings for those units listed.

The following provides approximate
Husqvarna
70 LP
Setting

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

G

H

J

K

M

N

N1/2

O

P1/2

Q

R

S

T

U

V

X

Z

Lesco
Hi-WHEEL
Setting

E

F

G

H

I

J

K

L

—

—

M

N

O

—

P

R

S

Scott
Speedy Green
Setting

—

—

2

—

3

—

4

—

5

—

6

—

7

—

8

—

—

I

J

L

M

O

P

—

Q

—

S

T

U

—

V

W

X

Z

Prizelawn
BF-1 /SS,HVO,
CBRlll, Setting

Scotts
R8A/SR-1,
AP&SR2000
Setting

The following provides approximate

70 LP settings when only the product weight, square

foot coverage, and visual inspection of the material is available.

FERTILIZER
PARTICLE SIZE

BAG RATE
Pounds of fertilizer used per
1,000 sq. ft. of coverage

5
10
15
5
10
15
1
2
3
5
10
15
5
10
15

Large, heavy
particles
Medium- mixed
particles
Small particles
(nitrogen)
Mixed size particles
-some fines
Light weight
particles

APPROX.
SETTING

APPROX.
SPREAD
WIDTH

6
9
11
5
7
9
2
4
5
6
9
11
4
5
6

12 FT.
12 FT.
12 FT.
10 FT.
10 FT.
10 FT.
10 FT.
10 FT.
10 FT.
8 FT.
8 FT.
8 FT.
6 FT.
To
8 FT.

The conversions should be used as guidelines for establishing proper rate settings for the particular product
being applied. Steps for obtaining the most accurate settings are outlined in the “How to Determine Spreader
Settings and Spread Width” section of this manual.
These settings are approximate and may vary due to physical characteristics of the product. Walking speed.
wear, condition of the turf and humidity, may cause actual rate setting to deviate. No expressed nor implied
warranty or guarantee is provided as to coverage or uniformity indicated by these rate settings.

6

MAINTENANCE
1. Never store unused material in spreader. Return
unused product to its original container.

Oil Impeller Shaft
Bearing In Hopper

2. Open and wash spreader thoroughly after each
use and dry completely in sun or heated area.
3. Oil the axle bearings, impeller shaft bearing in
hopper.
4. Remove gear cover and wash gears thoroughly.
Oil all bearing areas and face of gear teeth. Reinstall gear cover.
5. Gear mesh should be checked on a regular basis
during high use periods. Clearance between the
axle gear and pinion gear should be minimal but not
tight. If adjustment is necessary, loosen axle collar
set screw and hold gears together. Slide axle collar
against the gear support and tighten axle collar set
screw. Spin drive wheel. Gears should run freely
and smoothly.

Oil
Axle Collar

6. Impeller surface should be cleaned periodically to
remove build-up of product. Build-up can cause the
spread pattern to change.
7. Tire pressure should be 20-25 PSI.
Oil

NOTES

7

Oil

Parts List Model 70 LP
26

31
27

25

24

28
29

30

1
1A

23

32

2

3
4

22

7

21
20

5
19

6

16
15
8

18
17

9
14

PART OF OUR SERVICE IS
PROVIDING REPLACEMENT
PARTS. Parts may be obtained
through your local distributor.
be sure to give:

10
7

13

11

12

1. SPREADER MODEL NUMBER
2. SPREADER NAME
3. PART NUMBER

7349 Statesville Road

4. NAME OF PART AS SHOWN

Charlotte, NC. 28269
(800) 448-7543

Ke
y

Description

Part No.

Key
No.

Description

Part No.

1
1A
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

Hopper Assembly
Hopper *
Shutoff Plate *
Shutoff Plate Guides (Set)*
Rate Cam & Chute Assembly *
Impeller Assembly
Frame Assembly
Drive & Free Turning Wheel
Axle Collar
Axle Gear
Gear Cover Assembly (2 Req.)
Gear Cover Clamp (3 Req.)
Axle
Axle Bushing (2 Req.)
Impeller
Pinion Gear
Gear Support

525 56 82-06
525 56 82-07
525 56 84-03
525 56 84-04
525 56 83-03
525 56 87-05
525 556 92-02
525 56 96-02
525 56 86-06
525 56 86-05
525 56 88-05
525 56 88-06
525 56 86-07
525 56 86-08
525 56 87-01
525 56 88-07
525 56 88-08

17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

Impeller Shaft
Screen Clip (2 Req.)
Hopper Screen
Hopper Label *
Handle Brace W/ Plug– LH.
Agitator
Upper Handle Assembly
Handle Grip (2 Req.)
On/Off Control
Cable Clamp
Bracket-Cable Clamp
Handle Brace W/ Plug– RH.
Hopper Plug*
Impeller Shaft Bearing *
Fastener/Parts Package
Hopper Cover

525 56 87-06
525 56 91-02
525 56 82-08
525 56 82-08
525 56 85-05
525 57 00-01
525 56 85-07
525 56 85-08
525 56 93-02
525 56 90-01
525 56 90-02
525 56 85-06
525 56 82-11
525 56 87-07
525 56 94-02
525 56 82-09

* Parts included in Hopper Assembly



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2009:02:26 14:41:25Z
Modify Date                     : 2009:03:18 07:49:33-04:00
Page Count                      : 8
Page Mode                       : UseOutlines
Page Layout                     : OneColumn
Producer                        : GPL Ghostscript 8.15
Creation Date                   : 2009:02:26 14:41:25Z
Mod Date                        : 2009:03:18 07:49:33-04:00
Author                          : Husqvarna
Metadata Date                   : 2009:03:18 07:49:33-04:00
Title                           : OM, 70 LP Broadcast Spreader, 966043502, 2009-02, Accessory
Creator                         : Husqvarna
EXIF Metadata provided by EXIF.tools

Navigation menu