Husqvarna Yth 2448 Users Manual OM, (917.279081), 960130007, 2005 08, Ride Mower

YTH 2448 to the manual 47d65c1c-e771-4dbf-b9a6-908c6d63443d

2015-01-24

: Husqvarna Husqvarna-Yth-2448-Users-Manual-317335 husqvarna-yth-2448-users-manual-317335 husqvarna pdf

Open the PDF directly: View PDF .
Page Count: 48

Download
Open PDF In Browser	View PDF

02777

917.279081
(YTH2448)
Owner's Manual

SAFETY RULES
Safe Operation Practices for Ride-On Mowers
IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE
TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

•
WARNING: In order to prevent accidental starting when setting up,
transporting, adjusting or making repairs, always disconnect spark plug
wire and place wire where it cannot
contact spark plug.

•
•
•

WARNING: Do not coast down a hill
in neutral, you may lose control of the
tractor.

•
•

WARNING: Tow only the attachments
that are recommended by and comply with specifications of the manufacturer of your tractor. Use common
sense when towing. Operate only at
the lowest possible speed when on a
slope. Too heavy of a load, while on
a slope, is dangerous. Tires can lose
traction with the ground and cause you
to lose control of your tractor.

•
•
•
•

WARNING

•

Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals
known to the State of California to cause cancer and
birth defects or other reproductive harm.

•

WARNING

II. SLOPE OPERATION

Battery posts, terminals and related accessories
contain lead and lead compounds, chemicals known
to the State of California to cause cancer and birth
defects or other reproductive harm. Wash hands
after handling.

I. GENERAL OPERATION
•
•
•
•
•
•
•
•

Read, understand, and follow all instructions on the
machine and in the manual before starting.
Do not put hands or feet near rotating parts or under
the machine. Keep clear of the discharge opening at
all times.
Only allow responsible adults, who are familiar with the
instructions, to operate the machine.
Clear the area of objects such as rocks, toys, wire, etc.,
which could be picked up and thrown by the blades.
Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area.
Never carry passengers.
Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while backing.
Never direct discharged material toward anyone. Avoid
discharging material against a wall or obstruction. Material may ricochet back toward the operator. Stop the
blades when crossing gravel surfaces.

Do not operate machine without the entire grass catcher,
discharge guard, or other safety devices in place and
working.
Slow down before turning.
Never leave a running machine unattended. Always
turn off blades, set parking brake, stop engine, and
remove keys before dismounting.
Disengage blades when not mowing. Shut off engine
and wait for all parts to come to a complete stop before
cleaning the machine, removing the grass catcher, or
unclogging the discharge guard.
Operate machine only in daylight or good artificial
light.
Do not operate the machine while under the influence
of alcohol or drugs.
Watch for traffic when operating near or crossing roadways.
Use extra care when loading or unloading the machine
into a trailer or truck.
Always wear eye protection when operating machine.
Data indicates that operators, age 60 years and above,
are involved in a large percentage of riding mower-related injuries. These operators should evaluate their
ability to operate the riding mower safely enough to
protect themselves and others from serious injury.
Follow the manufacturer's recommendation for wheel
weights or counterweights.
Keep machine free of grass , leaves or other debris
build-up which can touch hot exhaust / engine parts
and burn. Do not allow the mower deck to plow leaves
or other debris which can cause build-up to occur.
Clean any oil or fuel spillage before operating or
storing the machine. Allow machine to cool before
storage.

Slopes are a major factor related to loss of control and
tip-over accidents, which can result in severe injury or
death. Operation on all slopes requires extra caution. If
you cannot back up the slope or if you feel uneasy on it,
do not mow it.
• Mow up and down slopes, not across.
• Watch for holes, ruts, bumps, rocks, or other hidden
objects. Uneven terrain could overturn the machine.
Tall grass can hide obstacles.
• Choose a low ground speed so that you will not have
to stop or shift while on the slope.
• Do not mow on wet grass. Tires may lose traction.
Always keep the machine in gear when going down
slopes. Do not shift to neutral and coast downhill.
• Avoid starting, stopping, or turning on a slope. If the
tires lose traction, disengage the blades and proceed
slowly straight down the slope.
• Keep all movement on the slopes slow and gradual.
Do not make sudden changes in speed or direction,
which could cause the machine to roll over.
• Use extra care while operating machine with grass
catchers or other attachments; they can affect the
stability of the machine. Do no use on steep slopes.
• Do not try to stabilize the machine by putting your foot
on the ground.
• Do not mow near drop-offs, ditches, or embankments.
The machine could suddenly roll over if a wheel is over
the edge or if the edge caves in.

SAFETY RULES
Safe Operation Practices for Ride-On Mowers
III. CHILDREN

GENERAL SERVICE
• Never operate machine in a closed are.
• Keep all nuts and bolts tight to be sure the equipment
is in safe working condition.
• Never tamper with safety devices. Check their proper
operation regularly.
• Keep machine free of grass, leaves, or other debris
build-up. Clean oil or fuel spillage and remove any fuelsoaked debris. Allow machine to cool before storing.
• If you strike a foreign object, stop and inspect the
machine. Repair, if necessary, before restarting.
• Never make any adjustments or repairs with the engine
running.
• Check grass catcher components and the discharge
guard frequently and replace with manufacturer's recommended parts, when necessary.
• Mower blades are sharp. Wrap the blade or wear
gloves, and use extra caution when servicing them.
• Check brake operation frequently. Adjust and service
as required.
• Maintain or replace safety and instruction labels, as
necessary.

Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to
the machine and the mowing activity. Never assume that
children will remain where you last saw them.
• Keep children out of the mowing area and in the watchful
care of a responsible adult other than the operator.
• Be alert and turn machine off if a child enters the
area.
• Before and while backing, look behind and down for
small children.
• Never carry children, even with the blades shut off. They
may fall off and be seriously injured or interfere with
safe machine operation. Children who have been given
rides in the past may suddenly appear in the mowing
area for another ride and be run over or backed over
by the machine.
• Never allow children to operate the machine.
• Use extra care when approaching blind corners, shrubs,
trees, or other objects that may block your view of a
child.

IV. TOWING
•
•
•
•
•

Tow only with a machine that has a hitch designed for
towing. Do not attach towed equipment except at the
hitch point.
Follow the manufacturer's recommendation for weight
limits for towed equipment and towing on slopes.
Never allow children or others in or on towed equipment.
On slopes, the weight of the towed equipment may
cause loss of traction and loss of control.
Travel slowly and allow extra distance to stop.

•
•
•

V. SERVICE
SAFE HANDLING OF GASOLINE
To avoid personal injury or property damage, use extreme
care in handling gasoline. Gasoline is extremely flammable
and the vapors are explosive.
• Extinguish all cigarettes, cigars, pipes, and other
sources of ignition.
• Use only approved gasoline container.
• Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling.
• Never fuel the machine indoors.
• Never store the machine or fuel container where there
is an open flame, spark, or pilot light such as on a water
heater or other appliances.
• Never fill containers inside a vehicle or on a truck or
trailer bed with plastic liner. Always place containers
on the ground away from your vehicle when filling.
• Remove gas-powered equipment from the truck or trailer
and refuel it on the ground. If this is not possible, then
refuel such equipment with a portable container, rather
than from a gasoline dispenser nozzle.
• Keep the nozzle in contact with the rim of the fuel tank
or container opening at all times until fueling is complete.
Do not use a nozzle lock-open device.
• If fuel is spilled on clothing, change clothing immediately.
• Never overfill fuel tank. Replace gas cap and tighten
securely.

•

•
•
•
•
•
•
•
•

Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area.
Never carry passengers.
Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while backing.
Never carry children, even with the blades shut off. They
may fall off and be seriously injured or interfere with
safe machine operation. Children who have been given
rides in the past may suddenly appear in the mowing
area for another ride and be run over or backed over
by the machine.
Keep children out of the mowing area and in the watchful
care of a responsible adult other than the operator.
Be alert and turn machine off if a child enters the
area.
Before and while backing, look behind and down for
small children.
Mow up and down slopes (15° Max), not across.
Choose a low ground speed so that you will not have
to stop or shift while on the slope.
Avoid starting, stopping, or turning on a slope. If the
tires lose traction, disengage the blades and proceed
slowly straight down the slope.
If machine stops while going uphill, disengage blades,
shift into reverse and back down slowly.
Do not turn on slopes unless necessary, and then, turn
slowly and gradually downhill, if possible.

PRODUCT SPECIFICATIONS
Gasoline Capacity
and type:

4 Gallons
Unleaded Regular

Oil Type (API-SG-SL):

SAE 30 (above 32°F)
SAE 5W-30 (below 32°F)

Oil Capacity:

W/ Filter:
W/O Filter:

Spark Plug:
(Gap: .040")

Champion QC12YC

Ground Speed (MPH):

Forward:
Reverse:

0 – 5.5
0 – 2.4

Tire Pressure:

Front:
Rear:

14 PSI
10 PSI

Charging System:

16 AMPS @ 3600 RPM

Battery:

AMP/HR:
MIN. CCA:
Case Size:

Blade Bolt Torque:

45-55FT. LBS.

CUSTOMER RESPONSIBILITIES
•
•
•

4.0 Pints
3.75 Pints

Read and observe the safety rules.
Follow a regular schedule in maintaining, caring for
and using your tractor.
Follow the instructions under “Maintenance” and “Storage” sections of this owner’s manual.

WARNING: This tractor is equipped with an internal combustion engine and should not be used on or near any
unimproved forest-covered, brush-covered or grass-covered
land unless the engine’s exhaust system is equipped with
a spark arrester meeting applicable local or state laws (if
any). If a spark arrester is used, it should be maintained
in effective working order by the operator.
In the state of California the above is required by law
(Section 4442 of the California Public Resources Code).
Other states may have similar laws. Federal laws apply on
federal lands.
A spark arrester for the muffler is available through your
nearest authorized service center/department (See REPAIR
PARTS section of this manual).

35
280
U1R

CONGRATULATIONS on your purchase of a new tractor.
It has been designed, engineered and manufactured to give
you the best possible dependability and performance.
Should you experience any problem you cannot easily remedy, please contact your nearest authorized servicecenter/
department We have competent, well-trained technicians
and the proper tools to service or repair this tractor.
Please read and retain this manual. The instructions will
enable you to assemble and maintain your tractor properly.
Always observe the “SAFETY RULES”.

TABLE OF CONTENTS
SAFETY RULES ......................................................... 2-3
PRODUCT SPECIFICATIONS ....................................... 4
CUSTOMER RESPONSIBILITIES................................. 4
ASSEMBLY ................................................................. 6-9
OPERATION ........................................................... 10-15
MAINTENANCE SCHEDULE ...................................... 16

MAINTENANCE ..................................................... 16-19
SERVICE AND ADJUSTMENTS ............................ 20-25
STORAGE .................................................................... 26
TROUBLESHOOTING ............................................ 27-28
REPAIR PARTS - TRACTOR .................................. 30-45

UNASSEMBLED PARTS
Mower

Steering Wheel

(2)Flanged
Pins

(1)Front Plate
Assembly
Steering
Wheel
Adapter

(2) Retainer Springs
(single loop)

Steering
Wheel Insert

(5) Retainer Springs
(double loop)

Gauge Wheels
(4) Shoulder Bolts

(4) Adjusting Bars

(4) Locknuts 3/8-16

(4) Wheels
(4) Washers
3/8 x 3/4 x 14 Ga.

(4) Retainer Springs
(double loop)

(4) Clevis Pins

Seat

Nose Roller
Rod

(2) Locknuts
5/16 x 18
(1) Washer 17/32 x 1-3/16 x 12 Gauge

(2) Hex Bolts
5/16 x 18 x 1

(1) Knob

Nose Roller

Slope Sheet

Keys
(2) Keys

Retainer Spring

Nose
Roller
Brackets

(1) Oil Drain Tube
For Future Use

ASSEMBLY
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.
To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use
the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

STEERING
WHEEL INSERT

A socket wrench set will make assembly easier. Standard
wrench sizes are listed.
(1) Tire pressure gauge
(2) 3/4" wrenches
(1) Utility knife
(2) 7/16" wrenches
(1) 3/4" socket w/drive ratchet
(1) Pliers
When right or left hand is mentioned in this manual, it means
when you are in the operating position (seated behind the
steering wheel).

1/2 HEX NUT
LARGE FLAT
WASHER

STEERING
WHEEL

TO REMOVE TRACTOR FROM
CARTON

ADAPTER

UNPACK CARTON
•
•
•
•

Remove all accessible loose parts and parts cartons
from carton .
Cut along dotted lines on all four panels of carton.
Remove end panels and lay side panels flat.
Remove mower and packing materials.
Check for any additional loose parts or cartons and
remove.

STEERING
SHAFT

277

BEFORE REMOVING TRACTOR FROM
SKID
FIG. 1

ATTACH STEERING WHEEL (See Fig. 1)
•
•
•
•
•
•

Remove locknut and large flat washer from steering
shaft.
Position front wheels of the tractor so they are pointing
straight forward.
Position steering wheel so cross bars are horizontal
(left to right) and slide onto steering wheel adapter.
Secure steering wheel to steering shaft with locknut
and large flat washer previously removed. Tighten
securely.
Snap steering wheel insert into center of steering
wheel.
Remove protective materials from tractor hood and
grill.

CHECK BATTERY (See Fig. 2)
•
•

Lift hood to raised position.
If this battery is put into service after month and year
indicated on label (label located between terminals)
charge battery for minimum of one hour at 6-10 amps.
(See "BATTERY" in Maintenance section of this manual
for charging instructions).
LABEL

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN
SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO
ROLL OFF SKID.

02746

FIG. 2

ASSEMBLY
INSTALL SEAT (See Fig. 3)

TO DRIVE TRACTOR OFF SKID (See Operation section for location and function of
controls)

Adjust seat before tightening adjustment knob.
• Remove adjustment knob and flat washer securing
seat to cardboard packing and set aside for assembly
of seat to tractor.
• Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.
• Place seat on seat pan so head of shoulder bolt is
positioned over large slotted hole in pan.
• Push down on seat to engage shoulder bolt in slot and
pull seat towards rear of tractor.
• Pivot seat and pan forward and assemble adjustment
knob and flat washer loosely. Do not tighten.
• Lower seat into operating position and sit on seat.
• Slide seat until a comfortable position is reached
which allows you to press clutch/brake pedal all the
way down.
• Get off seat without moving its adjusted position.
• Raise seat and tighten adjustment knob securely.
SEAT

WARNING: Before starting, read, understand and follow
all instructions in the Operation section of this manual. Be
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other people and objects.
• Be sure all the above assembly steps have been completed.
• Check engine oil level and fill fuel tank with gasoline.
• Place freewheel control in "transmission engaged"
position (see "TO TRANSPORT" in Operation section
of this manual).
• Sit on seat in operating position, depress clutch/brake
pedal and set the parking brake.
• Place motion control lever in neutral (N) position.
• Press lift lever plunger and raise attachment lift lever
to its highest position.
• Start the engine. After engine has started, move throttle
control to idle position.
• Release parking brake.
• Slowly move the motion control lever forward and slowly
drive tractor off skid.
• Apply brake to stop tractor, set parking brake and place
motion control lever in neutral position.
• Turn ignition key to "STOP" position.
Continue with the instructions that follow.

SHOULDER
BOLT

SEAT PAN

TO ATTACH NOSE ROLLER (See Fig. 4)
•

Assemble brackets "A" and "B" to the inside of mower
mounting brackets as shown. Tighten securely.
NOTE: Be sure bracket tabs are positioned in tab holes
in mower brackets.
• Position nose roller between brackets and install rod
and retainer spring.

FLAT WASHER
LOCK
NUT

ADJUSTMENT
KNOB

TAB
HOLE
02612

NOTE: You may now roll or drive your tractor off the skid.
Follow the appropriate instruction below to remove the
tractor from the skid.

RETAINER
SPRING

•
•

"A" BRACKET

NOSE
ROLLER

FIG. 4

TO ROLL TRACTOR OFF SKID (See Operation section for location and function of
controls)
•

ROD

"B"
BRACKET

02464

FIG. 3

•

HEX
BOLT

ASSEMBLE GAUGE WHEELS TO MOWER
DECK (See Fig. 5)

Press lift lever plunger and raise attachment lift lever
to its highest position.
Release parking brake by depressing clutch/brake
pedal.
Place freewheel control in "transmission disengaged
position" (See “TO TRANSPORT” in the Operation
section of this manual).
Roll tractor forward off skid.

The gauge wheels are designed to keep the mower deck
in proper position when operating mower. Be sure they
are properly adjusted to ensure optimum mower performance.
• Slide gauge wheel bar down into bracket channel, Be
sure that gauge wheel bar aligning holes are on top.
Assemble gauge wheels as shown using shoulder bolts,
3/8 washers and 3/8-16 center locknuts and tighten
securely.

ASSEMBLY
•
•

For ease of mower to tractor assembly, raise gauge
wheels to highest position and retain with clevis pins
and spring retainers.
Adjust gauge wheels before operating mower. See “TO
ADJUST GAUGE WHEELS” in the Operation section
of this manual.

•

If equipped, turn height adjustment knob counterclockwise until it stops.
• Lower mower linkage with attachment lift control.
• Install belt into electric clutch pulley groove.
• Place the suspension arms on outward pointing deck
pins. Retain with double loop retainer spring with loops
up as shown.
• Install front plate assembly to tractor suspension
brackets and retain with single loop retainer springs
as shown.
• Position front plate assembly between front mower
brackets. Raise deck and plate assembly to align holes
and insert flanged pins. Secure pins with double loop
retainer springs between the plate and mower brackets.
NOTE: To assist in locating hole in flanged pin, the hole in
pin is inline with notch on head of pin. If necessary, move
mower side-to-side to give space between plate and mower
brackets.
IMPORTANT: Check belt for proper routing in all mower
pulley grooves.
• Connect anti-sway bar to chassis bracket under left
footrest and retain with double loop retainer spring.
• If equipped, turn height adjustment knob clockwise to
remove slack from mower suspension.
• Raise deck to highest position.
• Adjust gauge wheels before operating mower as shown
in the Operation section of this manual.

RETAINER SPRING
PIN
ADJUSTING
BAR

SHOULDER
BOLT
GAUGE
WHEEL

3/8-16 CENTER
LOCKNUT

3/8 WASHER

FIG. 5

INSTALL MOWER AND DRIVE BELT
(See Figs. 6 and 7)
Be sure tractor is on level surface and mower suspension
arms are raised with attachment lift control. Engage parking brake.
• Cut and remove ties securing anti-sway bar and belts.
Swing anti-sway bar to left side of mower deck.
• Slide mower under tractor with deflector shield to right
side of tractor.
IMPORTANT: Check belt for proper routing in all mower
pulley grooves.

ELECTRIC
CLUTCH PULLEY
CHASSIS
BRACKET

FRONT
MOWER
BRACKET

FRONT SUSPENSION BRACKETS
DOUBLE LOOP
RETAINER
SPRING

GAUGE
WHEEL
FLANGED PIN

DOUBLE LOOP
RETAINER SPRING

FRONT
PLATE
ASSEMBLY

SINGLE
LOOP
RETAINER
SPRINGS

DEFLECTOR
SHIELD
ANTI-SWAY
BAR

USE PLIERS FOR
RETAINER SPRINGS

LOOP UP

SUSPENSION
ARMS
DOUBLE LOOP RETAINER
SPRING (OUTWARD POINTING
DECK PINS)

025
09

FIG. 6

ASSEMBLY
✓CHECKLIST

CHECK TIRE PRESSURE
The tires on your tractor were overinflated at the factory
for shipping purposes. Correct tire pressure is important
for best cutting performance.
• Reduce tire pressure to PSI shown in “PRODUCT
SPECIFICATIONS” section of this manual.

BEFORE YOU OPERATE YOUR NEW TRACTOR, WE
WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY
PRODUCT.
PLEASE REVIEW THE FOLLOWING CHECKLIST:
✓ All assembly instructions have been completed.
✓ No remaining loose parts in carton.
✓ Battery is properly prepared and charged. (Minimum
1 hour at 6 amps).
✓ Seat is adjusted comfortably and tightened securely.
✓ All tires are properly inflated. (For shipping purposes,
the tires were overinflated at the factory).
✓ Be sure mower deck is properly leveled side-to-side/
front-to-rear for best cutting results. (Tires must be
properly inflated for leveling).
✓ Check mower and drive belts. Be sure they are routed
properly around pulleys and inside all belt keepers.
✓ Check wiring. See that all connections are still secure
and wires are properly clamped.
✓ Before driving tractor, be sure freewheel control is in
“transmission engaged” position (see “TO TRANSPORT” in the Operation section of this manual).
WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY
EXTRA ATTENTION TO THE FOLLOWING IMPORTANT
ITEMS:
✓ Engine oil is at proper level.
✓ Fuel tank is filled with fresh, clean, regular unleaded
gasoline.
✓ Become familiar with all controls, their location and
function. Operate them before you start the engine.
✓ Be sure brake system is in safe operating condition.
✓ Be sure Operator Presence System and Reverse Operation System (ROS) are working properly (See the
Operation and Maintenance sections in this manual).
✓ It is important to purge the transmission before operating your tractor for the first time. Follow proper starting and transmission purging instructions (See “TO
START ENGINE” and “PURGE TRANSMISSION” in
the Operation section of this manual).

CHECK MOWER LEVELNESS
For best cutting results, mower should be properly leveled.
See “TO LEVEL MOWER HOUSING” in the Service and
Adjustments section of this manual.

CHECK FOR PROPER POSITION OF ALL
BELTS
See the figures that are shown for replacing motion, mower
drive, and mower blade drive belts in the Service and Adjustments section of this manual. Verify that the belts are
routed correctly.

CHECK BRAKE SYSTEM
After you learn how to operate your tractor, check to see that
the brake is properly adjusted. See “TO ADJUST BRAKE”
in the Service and Adjustments section of this manual.

OPERATION
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.

REVERSE

NEUTRAL

HIGH

LOW

CHOKE

FAST

SLOW
IGNITION SWITCH

ENGINE OFF

OVER TEMP
LIGHT

REVERSE
OPERATION
SYSTEM (ROS)

FUEL

ENGINE ON

OIL PRESSURE

ENGINE START

BATTERY

PARKING BRAKE

REVERSE

FORWARD

PARKING BRAKE
LOCKED

MOWER HEIGHT

PARKING BRAKE
UNLOCKED

MOWER LIFT

ATTACHMENT
CLUTCH DISENGAGED

ATTACHMENT
CLUTCH ENGAGED

BRAKE/CLUTCH
PEDAL

LIGHTS ON

SLOPE HAZARDS
KEEP AREA CLEAR
(SEE SAFETY RULES SECTION)

DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.
WARNING indicates a hazard which, if not avoided,
could result in death or serious injury.

FREE WHEEL
(Automatic Models only)
DANGER, KEEP HANDS
AND FEET AWAY

CAUTION indicates a hazard which, if not avoided,
might result in minor or moderate injury.
CAUTION when used without the alert symbol,
indicates a situation that could result in damage
to the tractor and/or engine.

Failure to follow instructions
could result in serious injury or
death. The safety alert symbol
is used to identify safety information about hazards which can
result in death, serious injury
and/or property damage.

HOT SURFACES indicates a hazard which,
if not avoided, could result in death, serious injury
and/or property damage.
FIRE indicates a hazard which, if not avoided,
could result in death, serious injury and/or
property damage.

OPERATION
KNOW YOUR TRACTOR
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR
Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments.
Save this manual for future reference.
ATTACHMENT
CLUTCH SWITCH

HOURMETER

ROS "ON"
POSITION

AMMETER
THROTTLE
CONTROL

LIFT LEVER
PLUNGER
ELAPSED TIME

IGNITION
SWITCH

0 0 0 000 00 00
HOURS

1/10

AMPS

ATTACHMENT
LIFT LEVER

CHOKE
CONTROL
CLUTCH/BRAKE
PEDAL
HEIGHT
ADJUSTMENT
INDICATOR

FREEWHEEL
CONTROL

LIGHT
SWITCH
PARKING BRAKE
MOTION
CONTROL
LEVER
02852_LSW

FIG. 7
Our tractors conform to the safety standards of the American National Standards Institute.
IGNITION SWITCH - Used for starting and stopping the
engine.
LIFT LEVER PLUNGER - Used to release attachment lift
lever when changing its position.
LIGHT SWITCH - Turns the headlights on.
MOTION CONTROL LEVER - Selects the speed and
direction of tractor.
PARKING BRAKE - Locks clutch/brake pedal into the
brake position.
REVERSE OPERATION SYSTEM (ROS) “ON” POSITION - Allows operation of mower deck or other powered
attachment while in reverse.
THROTTLE CONTROL - Used to control engine speed.

AMMETER - Indicates charging (+) or discharging (-) of
battery.
ATTACHMENT CLUTCH SWITCH - Used to engage the
mower blades, or other attachments mounted to your
tractor.
ATTACHMENT LIFT LEVER - Used to raise, lower and
adjust the mower deck or other attachments mounted to
your tractor.
CHOKE CONTROL - Used when starting a cold engine.
CLUTCH/BRAKE PEDAL - Used for declutching and
braking the tractor and starting the engine.
FREE WHEEL CONTROL - Disengages transmission for
pushing or slowly towing the tractor with the engine off.
HOURMETER- Indicates hours of operation.

OPERATION

00155

The operation of any tractor can result in foreign objects thrown into the eyes, which can result
in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or
performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles
or standard safety glasses.
NOTE: Under certain conditions when tractor is standing
idle with the engine running, hot engine exhaust gases may
cause “browning” of grass. To eliminate this possibility, always stop engine when stopping tractor on grass areas.

HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE (See Fig. 8)
Your tractor is equipped with an operator presence sensing switch. When engine is running, any attempt by the
operator to leave the seat without first setting the parking
brake will shut off the engine.
• Depress clutch/brake pedal into full “BRAKE” position
and hold.
• Place parking brake lever in “ENGAGED” position and
release pressure from clutch/brake pedal. Pedal should
remain in “BRAKE” position. Make sure parking brake
will hold tractor secure.
THROTTLE
CONTROL

PUSH IN TO
“DISENGAGE”

CAUTION: Always stop tractor completely, as described above, before leaving the operator's position; to empty
grass catcher, etc.

TO USE THROTTLE CONTROL (See Fig. 8)
Always operate engine at full throttle.
• Operating engine at less than full throttle reduces the
battery charging rate.
• Full throttle offers the best bagging and mower performance.

ATTACHMENT
CLUTCH SWITCH
PULL OUT TO
“ENGAGE”

TO USE CHOKE CONTROL (See Fig. 8)

CHOKE

Use choke control whenever you are starting a cold engine.
Do not use to start a warm engine.
• To engage choke control, pull knob out. Slowly push
knob in to disengage.

02774

IGNITION KEY
“BRAKE”
POSITION

CLUTCH/BRAKE
PEDAL “DRIVE”
POSITION

PARKING
BRAKE
“DISENGAGED” “ENGAGED”
POSITION
POSITION

MOTION
CONTROL
LEVER

TO MOVE FORWARD AND BACKWARD
(See Fig. 8)
The direction and speed of movement is controlled by the
motion control lever.
• Start tractor with motion control lever in neutral (N)
position.
• Release parking brake.
• Slowly move motion control lever to desired position.

FIG. 8

STOPPING (See Fig. 8)

TO ADJUST MOWER CUTTING HEIGHT
(See Fig. 8)

MOWER BLADES • To stop mower blades,move attachment clutch switch
to “DISENGAGED” position.
GROUND DRIVE • To stop ground drive, depress clutch/brake pedal into
full “BRAKE” position..
• Move motion control lever to neutral (N) position.

The position of the attachment lift lever determines the
cutting height.
• Grasp lift lever.
• Press plunger with thumb and move lever to desired
position.
The cutting height range is approximately 1-1/2 to 4".
The heights are measured from the ground to the blade tip
with the engine not running. These heights are approximate
and may vary depending upon soil conditions, height of
grass and types of grass being mowed.
• The average lawn should be cut to approximately 2-1/2
inches during the cool season and to over 3 inches
during hot months. For healthier and better looking
lawns, mow often and after moderate growth.
• For best cutting performance, grass over 6 inches
in height should be mowed twice. Make the first cut
relatively high; the second to desired height.

IMPORTANT:
THE MOTION CONTROL LEVER DOES NOT
RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/
BRAKE PEDAL IS DEPRESSED.

ENGINE • Move throttle control between half and full speed (fast)
position.
NOTE: Failure to move throttle control between half and
full speed (fast) position, before stopping may cause engine
to “backfire”.
• Turn ignition key to “STOP” position and remove key.
Always remove key when leaving tractor to prevent
unauthorized use.
• Never use choke to stop engine.

TO ADJUST GAUGE WHEELS (See Fig. 9)

IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY
POSITION OTHER THAN "STOP" WILL CAUSE THE BATTERY
TO BE DISCHARGED, (DEAD).

Gauge wheels are properly adjusted when they are slightly
off the ground when mower is at the desired cutting height
in operating position. Gauge wheels then keep the deck
in proper position to help prevent scalping in most terrain
conditions.

OPERATION
REVERSE OPERATION SYSTEM (ROS)

NOTE:Adjust gauge wheels with tractor on a flat level
surface.
• Adjust mower to desired cutting height (See “TO ADJUST MOWER CUTTING HEIGHT” in the Operation
section of this manual).
• Remove retainer spring and clevis pin which secure
each gauge wheel bar.
• Lower gauge wheels to ground. Raise gauge wheels
slightly to align holes in bracket and gauge wheel bar
and insert clevis pin. Gauge wheels should be slightly
off the ground.
• Replace retainer spring into clevis pin.
• Be sure all gauge wheels are in the same setting.

Your tractor is equipped with a Reverse Operation System
(ROS). Any attempt by the operator to travel in the reverse
direction with the attachment clutch engaged will shut off
the engine unless ignition key is placed in the ROS "ON"
position.
WARNING: Backing up with the attachment clutch engaged while mowing is
strongly discouraged. Turning the ROS
"ON", to allow reverse operation with
the attachment clutch engaged, should
only be done when the operator decides
it is necessary to reposition the machine with the attachment engaged. Do
not mow in reverse unless absolutely
necessary.

IMPORTANT: BE SURE TO READJUST GAUGE WHEELS IFYOU
CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.

USING THE REVERSE OPERATION SYSTEM • Move motion control lever to neutral (N) position.
• With engine running, turn ignition key counterclockwise
to ROS "ON" position.
• Look down and behind before backing.
• Slowly move motion control lever to reverse (R) position
to start movement.
• When use of the ROS is no longer needed, turn the
ignition key clockwise to engine "ON" position.

RETAINER
SPRING
01
97
7

CLEVIS
PIN

ROS "ON" POSITION

FIG. 9

ENGINE "ON" POSITION
(NORMAL OPERATING)

TO OPERATE MOWER (See Fig. 10)
Your tractor is equipped with an operator presence sensing
switch. Any attempt by the operator to leave the seat with
the engine running and the attachment clutch engaged will
shut off the engine. You must remain fully and centrally
positioned in the seat to prevent the engine from hesitating
or cutting off when operating your equipment on rough,
rolling terrain or hills.
• Select desired height of cut.
• Start mower blades by engaging attachment clutch
control.
• TO STOP MOWER BLADES - disengage attachment
clutch control.

02828

TO OPERATE ON HILLS
WARNING: Do not drive up or down
hills with slopes greater than 15° and
do not drive across any slope.
•

CAUTION: Do not operate the mower
without either the entire grass catcher,
on mowers so equipped, or the deflector shield in place.

•
•
•

ATTACHMENT CLUTCH
SWITCH PULL OUT TO
"ENGAGE"

ATTACHMENT
LIFT LEVER HIGH
POSITION

•

IMPORTANT:
THE MOTION CONTROL LEVER DOES NOT
RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/
BRAKE PEDAL IS DEPRESSED.

LOW
POSITION

•
PUSH IN TO
"DISENGAGE"
02

77
5

FIG. 10

Choose the slowest speed before starting up or down
hills.
Avoid stopping or changing speed on hills.
If slowing is necessary, move throttle control lever to
slower position.
If stopping is absolutely necessary, push clutch/brake
pedal quickly to brake position and engage parking
brake.
Move motion control lever to neutral (N) position.

•
•

DEFLECTOR
SHIELD

To restart movement, slowly release parking brake and
clutch/brake pedal.
Slowly move motion control lever to slowest setting.
Make all turns slowly.

OPERATION
TO TRANSPORT (See Figs. 7 and 11)

ADD GASOLINE

When pushing or towing your tractor, be sure to disengage
transmission by placing freewheel control in freewheeling
position. Free wheel control is located at the rear drawbar
of tractor.
• Raise attachment lift to highest position with attachment
lift control.
• Pull freewheel control out and down into the slot and
release so it is held in the disengaged position.
• Do not push or tow tractor at more than two (2)
MPH.
• To reengage transmission, reverse above procedure.
NOTE: To protect hood from damage when transporting
your tractor on a truck or a trailer, be sure hood is closed
and secured to tractor. Use an appropriate means of tying
hood to tractor (rope, cord, etc.).

•

CAUTION: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
IMPORTANT: WHEN OPERATING IN TEMPERATURES
BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE
GAS O LINE TO HELP INSURE GOOD COLD WEATHER
STARTING.

CAUTION: Alcohol blended fuels (called
gasohol or using ethanol or methanol) can attract moisture which leads to separation and
formation of acids during storage. Acidic gas
can damage the fuel system of an engine while
in storage. To avoid engine problems, the fuel
system should be emptied before storage of
30 days or longer. Drain the gas tank, start
the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel next
season. See Storage Instructions for additional
information. Never use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur.

02219

FIG. 11

TOWING CARTS AND OTHER AT TACH MENTS

TO START ENGINE (See Fig. 8)

Tow only the attachments that are recommended by and
comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load,
while on a slope, is dangerous. Tires can lose traction with
the ground and cause you to lose control of your tractor.

When starting the engine for the first time or if the engine
has run out of fuel, it will take extra cranking time to move
fuel from the tank to the engine.
• Be sure freewheel control is in the transmission engaged
position.
• Sit on seat in operating position, depress clutch/brake
pedal and set parking brake.
• Place motion control lever in neutral (N) position.
• Move attachment clutch to “DISENGAGED” position.
• Move throttle control to fast position
• Pull choke control out for a cold engine start attempt.
For a warm engine start attempt the choke control may
not be needed.
NOTE: Before starting, read the warm and cold starting
procedures below.
• Insert key into ignition and turn key clockwise to
“START” position and release key as soon as engine
starts. Do not run starter continuously for more than
fifteen seconds per minute. If the engine does not start
after several attempts, push choke control in, wait a
few minutes and try again. If engine still does not start,
pull the choke control out and retry.

BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL
•
•
•

•
•

Fill fuel tank to bottom of filler neck. Do not overfill.
Use fresh, clean, regular unleaded gasoline with a
minimum of 87 octane. (Use of leaded gasoline will
increase carbon and lead oxide deposits and reduce
valve life). Do not mix oil with gasoline. Purchase fuel
in quantities that can be used within 30 days to assure
fuel freshness.

The engine in your tractor has been shipped, from the
factory, already filled with summer weight oil.
Check engine oil with tractor on level ground.
Remove oil fill cap/dipstick and wipe clean, reinsert the
dipstick and screw cap tight, wait for a few seconds,
remove and read oil level. If necessary, add oil until
“FULL” mark on dipstick is reached. Do not overfill.
For cold weather operation you should change oil for
easier starting (See “OIL VISCOSITY CHART” in the
Maintenance section of this manual).
To change engine oil, see the Maintenance section in
this manual.

WARM WEATHER STARTING (50° F and above)
• When engine starts, slowly push choke control in until
the engine begins to run smoothly. If the engine starts
to run roughly, pull the choke control out slightly for a
few seconds and then continue to push the control in
slowly.

OPERATION
•

The attachments and ground drive can now be used. If
the engine does not accept the load, restart the engine
and allow it to warm up for one minute using the choke
as described above.

MOWING TIPS
•

COLD WEATHER STARTING (50° F and below)
• When engine starts, slowly push choke control in until
the engine begins to run smoothly. Continue to push
the choke control in small steps allowing the engine to
accept small changes in speed and load, until the choke
control is fully in. If the engine starts to run roughly, pull
the choke control out slightly for a few seconds and
then continue to push the control in slowly. This may
require an engine warm-up period from several seconds
to several minutes, depending on the temperature.

•
•

•

AUTOMATIC TRANSMISSION WARM UP
• Before driving the unit in cold weather, the transmission
should be warmed up as follows:
• Be sure the tractor is on level ground.
• Place the motion control lever in neutral.
Release the parking brake and let the clutch/
brake slowly return to operating position.
• Allow one minute for transmission to warm up. This
can be done during the engine warm up period.
• The attachments can be used during the engine warmup period after the transmission has been warmed
up and may require the choke control be pulled out
slightly.
NOTE: If at a high altitude (above 3000 feet) or in cold
temperatures (below 32 F) the carburetor fuel mixture may
need to be adjusted for best engine performance. See “TO
ADJUST CARBURETOR” in the Service and Adjustments
section of this manual.

Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the
Service and Adjustments section of this manual.
The left hand side of mower should be used for trimming.
Drive so that clippings are discharged onto the area
that has been cut. Have the cut area to the right of the
machine. This will result in a more even distribution of
clippings and more uniform cutting.
When mowing large areas, start by turning to the right so
that clippings will discharge away from shrubs, fences,
driveways, etc. After one or two rounds, mow in the
opposite direction making left hand turns until finished
(See Fig. 12).

00272

FIG. 12
•

•

PURGE TRANSMISSION
To ensure proper operation and performance, it is recommended that the transmission be purged before operating
tractor for the first time. This procedure will remove any
trapped air inside the transmission which may have developed during shipping of your tractor.

•

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE
REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD
BE PURGED AFTER REINSTALLATION BEFORE OPERATING
THE TRACTOR.

•

Place tractor safely in an area that is flat for approximately 80 feet in front of the tractor and set the parking
brake.
• Sitting in the tractor seat, start engine. After the engine
is running, move throttle control to slow position. With
motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.
• Slowly move motion control lever to full forward position
and hold for five (5) seconds, or approximately 40 feet.
Slowly move lever to full reverse position and hold for
five (5) seconds, or approximately 20 feet. After the
tractor moves approximately 20 feet in reverse return
the motion control lever to the neutral (N) position.
Your transmission is now purged and now ready for normal
operation.

If grass is extremely tall, it should be mowed twice to
reduce load and possible fire hazard from dried clippings. Make first cut relatively high; the second to the
desired height.
Do not mow grass when it is wet. Wet grass will plug
mower and leave undesirable clumps. Allow grass to
dry before mowing.
Always operate engine at full throttle when mowing to assure better mowing performance and proper
discharge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting
performance as well as the quality of cut desired.
When operating attachments, select a ground speed
that will suit the terrain and give best performance of
the attachment being used.

MAINTENANCE
MAINTENANCE SCHEDULE
FILL IN DATES
AS YOU COMPLETE
REGULAR SERVICE

E
E
S
S
RS
AG
US
RS
UR OUR
OU SON OR
U
O
H
O
H
H
A
0
ST
E
8H
SE RE
25
10
50
Y
Y
Y
Y
Y
RE
O
R
R
R
R
R
O
F
E
E
E
E
E
F
BE
SERVICE
EV
EV
EV
EV
EV
BE
H
AC

DATES

Check Brake Operation
Check Tire Pressure

T
R
A
C
T
0
R

Check Operator Presence and
ROS Systems
Check for Loose Fasteners
Sharpen/Replace Mower Blades

5
3

Lubrication Chart
Check Battery Level

Clean Battery and Terminals
Check Transaxle Cooling
Check V-Belts
Check Engine Oil Level
Change Engine Oil (with oil filter)
Change Engine Oil (without oil filter)

1,2

Clean Air Filter

Clean Air Screen

Inspect Muffler/Spark Arrester
Replace Oil Filter (If equipped)

1, 2

Clean Engine Cooling Fins

maint_sch-tractore.ROS.e

E
N
G
I
N
E

1,2

Replace Spark Plug
Replace Air Filter Paper Cartridge

Replace Fuel Filter
3 - Replace blades more often when mowing in sandy soil.
4 - Not required if equipped with maintenance-free battery.
5 - Tighten front axle pivot bolt to 35 ft.-lbs. maximum.
Do not overtighten.

1 - Change more often when operating under a heavy load or
in high ambient temperatures.
2 - Service more often when operating in dirty or dusty conditions.

GENERAL RECOMMENDATIONS

LUBRICATION CHART

The warranty on this tractor does not cover items that
have been subjected to operator abuse or negligence. To
receive full value from the warranty, operator must maintain
tractor as instructed in this manual.
Some adjustments will need to be made periodically to
properly maintain your tractor.
At least once a season, check to see if you should
make any of the adjustments described in the Service
and Adjustments section of this manual.
• At least once a year you should replace the spark
plug, clean or replace air filter, and check blades and
belts for wear. A new spark plug and clean air filter
assure proper air-fuel mixture and help your engine
run better and last longer.

•

➀

FRONT ➀
WHEEL
BEARING
ZERK

WHEEL
BEARING
ZERK

ENGINE

➁

01964

BEFORE EACH USE
•
•
•
•

SPINDLE ZERK

➀ SPINDLE ZERK
➀ FRONT

Check engine oil level.
Check brake operation.
Check tire pressure.
Check operator presence and
ROS systems for proper operation.
Check for loose fasteners.

➀ General Purpose Grease
➁ Refer to Maintenance “ENGINE” Section

IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS
WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS
LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL
SHORTEN THE LIFE OF THE SELF-LUBRICATING BEARINGS.
IF YOU FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY,
POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY.

MAINTENANCE
TRACTOR

BLADE CARE
For best results mower blades must be kept sharp. Replace
bent or damaged blades.

Always observe safety rules when performing any maintenance.
BRAKE OPERATION
If tractor requires more than five (5) feet to stop at highest
speed in highest gear on a level, dry concrete or paved
surface, then brake must be checked and adjusted. (See
“TO ADJUST BRAKE” in the Service and Adjustments
section of this manual).

CAUTION: Use only a replacement
blade approved by the manufacturer
of your tractor. Using a blade not approved by the manufacturer of your
tractor is hazardous, could damage
your tractor and void your warranty.

TIRES
• Maintain proper air pressure in all tires (See “PRODUCT
SPECIFICATIONS” section of this manual).
• Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.
• Avoid stumps, stones, deep ruts, sharp objects and
other hazards that may cause tire damage.
NOTE: To seal tire punctures and prevent flat tires due to
slow leaks, tire sealant may be purchased from your local
parts dealer. Tire sealant also prevents tire dry rot and
corrosion.

BLADE REMOVAL (See Fig. 13)
•

Raise mower to highest position to allow access to
blades.
NOTE: Protect your hands with gloves and/or wrap blade
with heavy cloth.
• Remove blade bolt by turning counterclockwise.
• Install new or resharpened blade with stamped "THIS
SIDE UP" facing deck and mandrel assembly.
IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER
HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL
ASSEMBLY.

OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS)
Be sure operator presence and reverse operation systems
are working properly. If your tractor does not function as
described, repair the problem immediately.
• The engine should not start unless the brake pedal is
fully depressed, and the attachment clutch control is
in the disengaged position.

•

IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.
BLADE

MANDREL
ASSEMBLY

CENTER
HOLE

CHECK OPERATOR PRESENCE SYSTEM
• When the engine is running, any attempt by the operator
to leave the seat without first setting the parking brake
should shut off the engine.
• When the engine is running and the attachment clutch
is engaged, any attempt by the operator to leave the
seat should shut off the engine.
• The attachment clutch should never operate unless
the operator is in the seat.

02
54

BLADE BOLT
(SPECIAL)

STAR

FIG. 13

TO SHARPEN BLADE (See Fig. 14)

CHECK REVERSE OPERATION (ROS) SYSTEM
• When the engine is running with the ignition switch in
the engine "ON" position and the attachment clutch
engaged, any attempt by the operator to shift into
reverse should shut off the engine.
• When the engine is running with the ignition switch in
the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse
should NOT shut off the engine.
ROS "ON" POSITION

Install and tighten blade bolt securely (45-55 Ft. Lbs.
torque).

NOTE: We do not recommend sharpening blade - but if
you do, be sure the blade is balanced.
Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and eventual
damage to mower and engine.
• The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the
mower.
• To check blade balance, you will need a 5/8" diameter
steel bolt, pin, or a cone balancer. (When using a
cone balancer, follow the instructions supplied with
balancer.)
NOTE: Do not use a nail for balancing blade. The lobes of
the center hole may appear to be centered, but are not.
• Slide blade on to an unthreaded portion of the steel bolt
or pin and hold the bolt or pin parallel with the ground.
If blade is balanced, it should remain in a horizontal
position. If either end of the blade moves downward,
sharpen the heavy end until the blade is balanced.

ENGINE "ON" POSITION
(NORMAL OPERATING)

828

MAINTENANCE
TRANSAXLE COOLING

CENTER
HOLE

The transmission fan and cooling fins should be kept clean
to assure proper cooling.
Do not attempt to clean fan or transmission while engine
is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure water or
steam to clean transaxle.
• Inspect cooling fan to be sure fan blades are intact and
clean.
• Inspect cooling fins for dirt, grass clippings and other
materials. To prevent damage to seals, do not use
compressed air or high pressure sprayer to clean cooling fins.

BLADE
5/8" BOLT OR PIN

FIG. 14

BATTERY
Your tractor has a battery charging system which is sufficient
for normal use. However, periodic charging of the battery
with an automotive charger will extend its life.
• Keep battery and terminals clean.
• Keep battery bolts tight.
• Keep small vent holes open.
• Recharge at 6-10 amperes for 1 hour.
NOTE: The original equipment battery on your tractor is
maintenance free. Do not attempt to open or remove caps
or covers. Adding or checking level of electrolyte is not
necessary.

TRANSAXLE PUMP FLUID
The transaxle was sealed at the factory and fluid maintenance is not required for the life of the transaxle. Should
the transaxle ever leak or require servicing, contact your
nearest authorized ser vice center/department.

ENGINE
LUBRICATION

TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the battery and terminals can cause
the battery to “leak” power.
• Remove terminal guard.
• Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor.
• Rinse the battery with plain water and dry.
• Clean terminals and battery cable ends with wire brush
until bright.
• Coat terminals with grease or petroleum jelly.
• Reinstall battery (See “REPLACING BATTERY" in
the SERVICE AND ADJUSTMENTS section of this
manual).

Only use high quality detergent oil rated with API service
classification SG-SL. Select the oil’s SAE viscosity grade
according to your expected operating temperature.
SAE VISCOSITY GRADES
SAE 30
5W-30
-20

F
C

-30

0
-20

30
-10

60
10

100

80
20

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
oil_visc_chart1_e

FIG. 15
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)
improve starting in cold weather, these multi-viscosity oils
will result in increased oil consumption when used above
32°F. Check your engine oil level more frequently to avoid
possible engine damage from running low on oil.

V-BELTS
Check V-belts for deterioration and wear after 100 hours
of operation and replace if necessary. The belts are not
adjustable. Replace belts if they begin to slip from wear.

Change the oil after every 50 hours of operation or at least
once a year if the tractor is not used for 50 hours in one
year.
Check the crankcase oil level before starting the engine
and after each eight (8) hours of operation. Tighten oil fill
cap/dipstick securely each time you check the oil level.

MAINTENANCE
TO CHANGE ENGINE OIL (SEE FIGS. 15 AND 16)
Determine temperature range expected before oil change.
All oil must meet API service classification SG-SL.
• Be sure tractor is on level surface.
• Oil will drain more freely when warm.
• Catch oil in a suitable container.
• Remove oil fill cap/dipstick. Be careful not to allow dirt
to enter the engine when changing oil.
• Remove yellow cap from bottom fitting of drain valve
and install the drain tube onto the fitting.

AIR FILTER
Your engine will not run properly using a dirty air filter.
Service air cleaner more often under dusty conditions. See
Engine Manual.

MUFFLER
Inspect and replace corroded muffler and spark arrester
(if equipped) as it could create a fire hazard and/or damage.

SPARK PLUGS
Replace spark plugs at the beginning of each mowing
season or after every 100 hours of operation, whichever
occurs first. Spark plug type and gap setting are shown in
“PRODUCT SPECIFICATIONS” section of this manual.

OIL DRAIN VALVE
CLOSED AND
LOCKED
POSITION

46
02

YELLOW
CAP

IN-LINE FUEL FILTER (See Fig. 17)
The fuel filter should be replaced once each season. If fuel
filter becomes clogged, obstructing fuel flow to carburetor,
replacement is required.
• With engine cool, remove filter and plug fuel line sections.
• Place new fuel filter in position in fuel line with arrow
pointing towards carburetor.
• Be sure there are no fuel line leaks and clamps are
properly positioned.
• Immediately wipe up any spilled gasoline.

DRAIN
TUBE

FIG. 16
•
•
•
•
•

•

Unlock drain valve by pushing inward and turning
counterclockwise.
To open, pull out on the drain valve.
After oil has drained completely, close and lock the
drain valve by pushing inward and turning clockwise
until the pin is in the locked position as shown.
Remove the drain tube and replace the cap onto to the
bottom fitting of the drain valve.
Refill engine with oil through oil fill dipstick tube. Pour
slowly. Do not overfill. For approximate capacity see
“PRODUCT SPECIFICATIONS” section of this manual.
Use gauge on oil fill cap/dipstick for checking level. For
accurate reading, insert dipstick into the tube and push
down firmly into place before removing. Keep oil up to,
but not over, the “FULL” line on dipstick. Push dipstick
down firmly into the tube when finished.

CLAMP

FUEL
FILTER

00667

FIG. 17

CLEANING
•

Clean engine, battery, seat, finish, etc. of all foreign
matter.
• Keep finished surfaces and wheels free of all gasoline,
oil, etc.
• Protect painted surfaces with automotive type wax.
We do not recommend using a garden hose or pressure
washer to clean your tractor unless the engine and transmission are covered to keep water out. Water in engine or
transmission will shorten the useful life of your tractor. Use
compressed air or a leaf blower to remove grass, leaves
and trash from tractor and mower.

CLEAN AIR SCREEN
Air screen must be kept free of dirt and chaff to prevent
engine damage from overheating. Clean with a wire brush
or compressed air to remove dirt and stubborn dried gum
fibers.

CLEAN AIR INTAKE/COOLING AREAS
To insure proper cooling, make sure the grass screen,
cooling fins, and other external surfaces of the engine are
kept clean at all times.
Every 100 hours of operation (more often under extremely
dusty, dirty conditions), remove the blower housing and
other cooling shrouds. Clean the cooling fins and external
surfaces as necessary. Make sure the cooling shrouds are
reinstalled.
NOTE: Operating the engine with a blocked grass screen,
dirty or plugged cooling fins, and/or cooling shrouds removed
will cause engine damage due to overheating.

SERVICE AND ADJUSTMENTS
WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:
• Depress clutch/brake pedal fully and set parking brake.
• Place motion control lever in neutral (N) position.
• Place attachment clutch in “DISENGAGED” position.
• Turn ignition key to “STOP” and remove key.
• Make sure the blades and all moving parts have completely stopped.
• Disconnect spark plug wire from spark plug and place wire where it cannot come in contact
with plug.

TRACTOR

TO INSTALL MOWER

TO REMOVE MOWER (See Fig. 18)

Be sure tractor is on level surface and mower suspension
arms are raised with attachment lift control. Engage parking brake.
• Swing anti-sway bar to left side of mower deck.
• Slide mower under tractor with deflector shield to right
side of tractor.

•
•
•
•
•
•
•
•
•

Place attachment clutch in “DISENGAGED” position.
If equipped, turn height adjustment knob to lowest
setting.
Lower mower to its lowest position.
Remove retainer spring holding anti-swaybar to chassis
bracket and disengage anti-swaybar from bracket.
Remove four retainer springs from front plate assembly
and remove plate.
Remove retainer springs from suspension arms at deck
and disengage arms from deck.
Raise attachment lift to its highest position.
Slide mower forward and remove belt from electric
clutch pulley.
Slide mower out from under right side of tractor.

SUSPENSION
ARMS

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL
MOWER PULLEY GROOVES.

•
•
•
•
•

If equipped, turn height adjustment knob counterclockwise until it stops.
Lower mower linkage with attachment lift control.
Install belt into electric clutch pulley groove.
Place the suspension arms on outward pointing deck
pins. Retain with double loop retainer spring with loops
up as shown.
Install front plate assembly to tractor suspension
brackets and retain with single loop retainer springs
as shown.

FRONT
MOWER
BRACKET

ELECTRIC
FRONT PLATE
CLUTCH
ASSEMBLY
PULLEY

CHASSIS
BRACKET

DOUBLE LOOP
RETAINER SPRING

SINGLE LOOP
REATINER
SPRING

RETAINER
SPRING

FLANGED PINS

ANTI-SWAY
BAR
USE PLIERS FOR
RETAINER SPRINGS

SUSPENSION ARMS
DOUBLE LOOP
RETAINER SPRINGS
(Outward pointing
deck pins)

02566

LOOP UP

FIG. 18

SERVICE AND ADJUSTMENTS
•

Position front plate assembly between front mower
brackets. Raise deck and plate assembly to align holes
and insert flanged pins. Secure pins with double loop
retainer springs between the plate and mower brackets.
NOTE: To assist in locating hole in flanged pin, the hole in
pin is inline with notch on head of pin. If necessary, move
mower side-to-side to give space between plate and mower
brackets.

FRONT-TO-BACK ADJUSTMENT (See Figs. 21 and 22)
IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE
FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY,
BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO
MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower blades should
be adjusted so the front tip is approximately 1/8" to 1/2"
lower than the rear tip when the mower is in its highest
position.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL
MOWER PULLEY GROOVES.

•
•
•

CAUTION: Blades are sharp. Protect
your hands with gloves and/or wrap
blade with heavy cloth.

Connect anti-sway bar to chassis bracket under left
footrest and retain with double loop retainer spring.
If equipped, turn height adjustment knob clockwise to
remove slack from mower suspension.
Raise deck to highest position.

Check adjustment on right side of tractor. Position any blade
so the tip is pointing straight forward. Measure distance "B"
at front and rear tip of the blade.
• Before making any necessary adjustments, check that
both front plate links are equal in length.
• If links are not equal in length, adjust one link to same
length as other link.
• To lower front of blade, loosen nut “C” on both front
links an equal number of turns.
NOTE: Each full turn of nut “C” will change distance. “B”
by approximately 3/16".
• When distance “B” is 1/8" to 1/2" lower at front than rear,
tighten nut “D” against trunnion on both front links.
• To raise front of blade, loosen nut “D” from trunnion on
both front links. Tighten nut “C” on both front links an
equal number of turns. The two front links must remain
equal in length.
• When distance “B” is 1/8" to 1/2" lower at front than rear,
tighten nut “D” against trunnion on both front links.
• Recheck side-to-side adjustment.

TO LEVEL MOWER HOUSING
Adjust the mower while tractor is parked on level ground
or driveway. Make sure tires are properly inflated (See
“PRODUCT SPECIFICATIONS” section of this manual). If
tires are over or underinflated, you will not properly adjust
your mower.
SIDE-TO-SIDE ADJUSTMENT (See Figs. 19 and 20)
• Raise mower to its highest position.
• Measure height from bottom edge of mower to ground
level at front corners of mower. Distance “A” on both
sides of mower should be the same.
• If adjustment is necessary, make adjustment on one
side of mower only.
• To raise one side of mower, tighten lift link adjustment
nut on that side.
• To lower one side of mower, loosen lift link adjustment
nut on that side.
NOTE: Each full turn of adjustment nut will change mower
height about 3/16".
• Recheck measurements after adjusting.
BOTTOM EDGE
OF MOWER TO
GROUND

BLADE
02548

BOTTOM EDGE
OF MOWER TO
GROUND

00598

“B”

FIG. 21
BOTH FRONT PLATE LINKS MUST BE
EQUAL IN LENGTH

GROUND LINE

FIG. 19
SUSPENSION
ARM

02
51
6

01553

LIFT LINK
ADJUSTMENT NUT

NUT “C”

NUT “D”

FIG. 20

0251

TRUNNION

FRONT PLATE
ASSEMBLY

FIG. 22

SERVICE AND ADJUSTMENTS
TO REPLACE MOWER BLADE (SECONDARY)
DRIVE BELT (See Fig. 24)

TO REPLACE MOWER DRIVE BELT
MOWER DRIVE BELT REMOVAL (See Fig. 23)
• Park tractor on a level surface. Engage parking
brake.
• Lower mower to its lowest position.
Remove screws from R.H. mandrel cover and remove
cover.
• Remove any dirt or grass clippings which may have
accumulated around mandrels and entire upper deck
surface.
• Disconnect R.H. suspension arm from rear deck bracket
by removing retainer spring.
• Roll belt over the top of R.H. mandrel pulley carefully.
• Remove belt from electric clutch pulley.
• Remove belt from idler pulleys.
• Check primary idler arm and two idlers to see that they
rotate freely.
• Be sure spring is securely hooked to primary idler arm
and spring arm.

Park the tractor on level surface. Engage parking brake.
• Remove mower (See “TO REMOVE MOWER” in this
section of manual).
• Remove screws from R.H. and L.H. mandrel covers
and remove covers.
REMOVE MOWER DRIVE BELT
(Refer to “TO REMOVE MOWER DRIVE BELT” illustration
in this section of manual).
• Carefully roll belt over the top of R.H. mandrel pulley.
• Remove belt from idler pulleys.
• Check primary idler arm and two idlers to see that they
rotate freely.
• Be sure spring is securely hooked to primary idler arm
and spring arm.
REMOVE MOWER BLADE (SECONDARY) DRIVE BELT
• Carefully roll belt off L.H. mandrel pulley.
• Remove belt from center mandrel pulley, idler pulley,
and R.H. mandrel pulley.
• Remove any dirt or grass which may have accumulated
around mandrels and entire upper deck surface.
• Check secondary idler arm and idler pulley to see that
they rotate freely.
• Be sure spring is hooked in secondary idler arm and
secondary spring arm.
INSTALL NEW MOWER BLADE (SECONDARY) DRIVE
BELT
• Install new belt in lower groove of R.H. mandrel pulley,
idler pulley, and center mandrel pulley as shown.
• Carefully roll belt over L.H. mandrel pulley. Make sure
belt is in all grooves properly.
REINSTALL MOWER DRIVE BELT
(Refer to “TO REMOVE MOWER DRIVE BELT” illustration
in this section of manual).
• Install belt into upper groove of R.H. mandrel pulley
and around both idlers. Pull belt to front of mower to
remove slack.
• Reinstall mandrel covers and securely tighten all
screws.
• Carefully check belt routing making sure belt is in all
grooves correctly.
• Reinstall mower to tractor (See “TO INSTALL MOWER”
in this section of manual).

MOWER DRIVE BELT INSTALLATION (See Fig. 23)
• Install belt in both idlers.
• Install new belt onto electric clutch pulley.
• Roll belt into upper groove of R.H. mandrel pulley carefully.
• Carefully check belt routing making sure belt is in the
grooves correctly.
• Reconnect R.H. suspension arm to rear deck bracket
with retainer spring.
• Reassemble R.H. mandrel cover.

RH MANDREL
COVER

ELECTRIC
CLUTCH
PULLEY

IDLER
PULLEYS

SECONDARY
IDLER ARM
SPRING
SECONDARY
SPRING ARM

L.H. MANDREL
SPRING ARM
RH SUSPENSION
ARM
PRIMARY IDLER ARM
R.H. MANDREL

CENTER
MANDREL

025

FIG. 23
IDLER
PULLEY
R.H. MANDREL

FIG. 24

025

SERVICE AND ADJUSTMENTS
TO CHECK AND ADJUST BRAKE
(See Fig. 25)

TO REPLACE MOTION DRIVE BELT
(See Fig. 26)

Your tractor is equipped with an adjustable brake system
which is mounted on the right side of the transaxle.
If tractor requires more than five (5) feet to stop at highest
speed in highest gear on a level, dry concrete or paved
surface, then brake must be checked and adjusted.

Park the tractor on level surface. Engage parking brake.
For assistance, there is a belt installation guide decal on
bottom side of left footrest.
BELT REMOVAL • Remove mower (See “TO REMOVE MOWER” in this
section of manual).
NOTE: Observe entire motion drive belt and position of all
belt guides and keepers.
• Remove belt from stationary idler and clutching idler.
• Remove belt downward from around engine pulley.
• Pull belt slack toward rear of tractor. Carefully remove
belt upwards from transmission input pulley.
• Remove belt from center span keeper and pull belt
away from tractor.

TO CHECK BRAKE
• Park tractor on a level, dry concrete or paved surface,
depress clutch/brake pedal all the way down and engage parking brake.
• Disengage transmission by placing freewheel control
in “transmission disengaged” position. Pull freewheel
control out and into the slot and release so it is held in
the disengaged position.
The rear wheels must lock and skid when you try to manually
push the tractor forward. If the rear wheels rotate, the brake
needs to be adjusted or the pads need to be replaced.

BELT INSTALLATION • Carefully work new belt down onto the input pulley.
• Slide belt into the center span keeper.
• Pull belt toward front of tractor and roll around the top
groove of engine pulley.
• Install belt through stationary idler and clutching
idler.
• Make sure belt is in all pulley grooves and inside all
belt guides and keepers.
• Install mower (See “TO INSTALL MOWER” in this section of manual).

TO ADJUST BRAKE
• Depress clutch/brake pedal all the way down and engage parking brake.
• Measure distance between brake operating arm and
nut “A” on brake rod.
• If distance is other than 1-9/16", loosen jam nut and
turn nut “A” until distance becomes 1-9/16". Retighten
jam nut against nut “A”.
• Engage transmission by placing freewheel control in
“transmission engaged” position.
• Road test tractor for proper stopping distance as stated
above. Readjust if necessary. If stopping distance is
still greater than five (5) feet in highest gear, further
maintenance is necessary. Replace brake pads or
contact a qualified service center.

ENGINE
PULLEY
CLUTCHING
IDLER
STATIONARY
IDLER

NUT “A”
1-9/16"

JAM NUT

OPERATING
ARM

TRANSMISSION
INPUT PULLEY

CENTER SPAN
KEEPER

FIG. 26
02557-LTH

FIG. 25

SERVICE AND ADJUSTMENTS
TRANSAXLE MOTION CONTROL LEVER
NEUTRAL ADJUSTMENT (See Fig. 27)

TO REMOVE WHEEL FOR REPAIRS
(See Fig. 28)

The motion control lever has been preset at the factory and
adjustment should not be necessary.
• Loosen adjustment bolt in front of the right rear wheel,
and lightly tighten.
• Start engine and move motion control lever until tractor
does not move forward or backward.
• Hold motion control lever in that position and turn engine
off.
• While holding motion control lever in place, loosen the
adjustment bolt.
• Move motion control lever to the neutral (N) (lock gate)
position.
• Tighten adjustment bolt securely.
NOTE: If additional clearance is needed to get to
adjustment bolt, move mower deck height to the lowest
osition.
After above adjustment is made, if the tractor still creeps
forward or backward while motion control lever is in
neutral position, follow these steps:
• Loosen the adjustment bolt.
• Move the motion control lever 1/4 to 1/2 inch in the
direction it is trying to creep.
• Tighten adjustment bolt securely.
• Start engine and test.
• If tractor still creeps, repeat above steps until satisfied.

•
•

Block up axle securely.
Remove axle cover, retaining ring and washers to allow
wheel removal (rear wheel contains a square key - Do
not lose).
• Repair tire and reassemble.
• On rear wheels only: align grooves in rear wheel hub
and axle. Insert square key.
• Replace washers and snap retaining ring securely in
axle groove.
• Replace axle cover.
NOTE: To seal tire punctures and prevent flat tires due
to slow leaks, tire sealant may be purchased from your
local parts dealer. Tire sealant also prevents tire dry rot
and corrosion.

WASHERS

AXLE
COVER

RETAINING
RING

3
0066

SQUARE KEY
(REAR WHEEL ONLY)

FIG. 28

MOTION CONTROL
LEVER

NEUTRAL
LOCK GATE

TO START ENGINE WITH A WEAK
BATTERY(See Fig. 29)
WARNING: Lead-acid batteries generate explosive gases. Keep sparks,
flame and smoking materials away from
batteries. Always wear eye protection
when around batteries.

ADJUSTMENT
BOLT

02239

FIG. 27

If your battery is too weak to start the engine, it should be
recharged. (See "BATTERY" in the MAINTENANCE section of this manual).
If “jumper cables” are used for emergency starting, follow
this procedure:

TRANSMISSION REMOVAL/REPLACEMENT
Should your transmission require removal for service or
replacement, it should be purged after reinstallation and
before operating the tractor. See “PURGE TRANSMISSION”
in the Operation section of this manual.

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT
SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT
SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START
OTHER VEHICLES.

TO ADJUST STEERING WHEEL
ALIGNMENT

TO ATTACH JUMPER CABLES • Connect one end of the RED cable to the POSITIVE
(+) terminal of each battery(A-B), taking care not to
short against tractor chassis.
• Connect one end of the BLACK cable to the NEGATIVE
(-) terminal (C) of fully charged battery.
• Connect the other end of the BLACK cable (D) to good
chassis ground, away from fuel tank and battery.

If steering wheel crossbars are not horizontal (left to right)
when wheels are positioned straight forward, remove steering wheel and reassemble per instructions in the Assembly
section of this manual.

FRONT WHEEL TOE-IN/CAMBER
The front wheel toe-in and camber are not adjustable on
your tractor. If damage has occurred to affect the front
wheel toe-in or camber, contact your nearest authorized
service center/department.

TO REMOVE CABLES, REVERSE ORDER • BLACK cable first from chassis and then from the fully
charged battery.
• RED cable last from both batteries.

SERVICE AND ADJUSTMENTS
INTERLOCKS AND RELAYS
Loose or damaged wiring may cause your tractor to run
poorly, stop running, or prevent it from starting.
• Check wiring. See electrical wiring diagram in the
Repair Parts section.

TO REPLACE FUSE
Replace with 20 amp automotive-type plug-in fuse. The
fuse holder is located behind the dash.
02614

WEAK OR DEAD
BATTERY

TO REMOVE HOOD AND GRILL ASSEMBLY
(See Fig. 31)

FULLY CHARGED
BATTERY

•
•
•

FIG. 29

REPLACING BATTERY (See Fig. 30)

•

WARNING: Do not short battery
terminals by allowing a wrench or any
other object to contact both terminals
at the same time. Before connecting battery, remove metal bracelets,
wristwatch bands, rings, etc.
Positive terminal must be connected
first to prevent sparking from accidental grounding.
•
•
•
•
•

HOOD

HEADLIGHT
WIRE
CONNECTOR

Lift hood to raised position.
Disconnect BLACK battery cable first then RED battery
cable and carefully remove battery from tractor.
Install new battery with terminals in same position as
old battery.
First connect RED battery cable to positive (+) terminal
with hex bolt and keps nut as shown. Tighten securely.
Slide terminal cover over terminal.
Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten
securely.
HEX
BOLT

KEPS NUT

Raise hood.
Unsnap headlight wire connector.
Stand in front of tractor. Grasp hood at sides, tilt toward
engine and lift off of tractor.
To replace, reverse above procedures.

02778

FIG. 31

ENGINE

TERMINAL
COVER

TO ADJUST THROTTLE CONTROL CABLE
The throttle control has been preset at the factory and
adjustment should not be necessary. If adjustment is necessary, see engine manual.

TO ADJUST CHOKE CONTROL

NEGATIVE
(BLACK)
CABLE

02747

The choke control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engne manual.

POSITIVE
(RED)
CABLE

TO ADJUST CARBURETOR
Your carburetor is not adjustable. If your engine does not
operate properly due to suspected carburetor problems,
take your tractor to an authorized service center for repair
and/or adjustment.

FIG. 30

TO REPLACE HEADLIGHT BULB
•
•
•
•

Raise hood.
Pull bulb holder out of the hole in the backside of the
grill.
Replace bulb in holder and push bulb holder securely
back into the hole in the backside of the grill.
Close hood.

STORAGE
Immediately prepare your tractor for storage at the end
of the season or if the tractor will not be used for 30 days
or more.

•

Empty the fuel tank by starting the engine and let it run
until the fuel lines and carburetor are empty.
• Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may occur.
• Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 minutes after adding stabilizer to
allow the stabilizer to reach the carburetor. Do not empty
the gas tank and carburetor if using fuel stabilizer.

WARNING: Never store the tractor with
gasoline in the tank inside a building
where fumes may reach an open flame
or spark. Allow the engine to cool before
storing in any enclosure.

TRACTOR
Remove mower from tractor for winter storage. When mower
is to be stored for a period of time, clean it thoroughly, remove
all dirt, grease, leaves, etc. Store in a clean, dry area.
• Clean entire tractor (See “CLEANING” in the Maintenance section of this manual).
• Inspect and replace belts, if necessary (See belt replacement instructions in the Service and Adjustments
section of this manual).
• Lubricate as shown in the Maintenance section of this
manual.
• Be sure that all nuts, bolts and screws are securely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary.
• Touch up all rusted or chipped paint surfaces; sand
lightly before painting.

ENGINE OIL
Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of
this manual).

CYLINDER(S)
•
•
•
•

OTHER

BATTERY
•
•
•

•
•

Remove spark plug(s).
Pour one ounce of oil through spark plug hole(s) into
cylinder(s).
Turn ignition key to “START” position for a few seconds
to distribute oil.
Replace with new spark plug(s).

•
•

Fully charge the battery for storage.
After a period of time in storage, battery may require
recharging.
To help prevent corrosion and power leakage during
long periods of storage, battery cables should be disconnected and battery cleaned thoroughly (see “TO
CLEAN BATTERY AND TERMINALS” in the Maintenance section of this manual).
After cleaning, leave cables disconnected and place
cables where they cannot come in contact with battery
terminals.
If battery is removed from tractor for storage, do not
store battery directly on concrete or damp surfaces.

•
•

Do not store gasoline from one season to another.
Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
If possible, store your tractor indoors and cover it to
give protection from dust and dirt.
Cover your tractor with a suitable protective cover that
does not retain moisture. Do not use plastic. Plastic
cannot breathe which allows condensation to form and
will cause your tractor to rust.

IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE AND
EXHAUST AREAS ARE STILL WARM.

ENGINE
FUEL SYSTEM
IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS
FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH
AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK
DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT
ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING
ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH
LEADS TO SEPARATION AND FORMATION OF ACIDS DURING
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM
OF AN ENGINE WHILE IN STORAGE.

TROUBLESHOOTING POINTS
PROBLEM
Will not start

CAUSE
1.
2.
3.
4.
5.
6.
7.

Out of fuel.
Engine not “CHOKED” properly.
Engine flooded.
Bad spark plug.
Dirty air filter.
Dirty fuel filter.
Water in fuel.

1.
2.
3.
4.
5.
6.
7.

8.
9.

Loose or damaged wiring.
Carburetor out of adjustment.

8.
9.

10.

Hard to start

CORRECTION

Engine valves out of adjustment.

10.

Fill fuel tank.
See “TO START ENGINE” in Operation section.
Wait several minutes before attempting to start.
Replace spark plug.
Clean/replace air filter.
Replace fuel filter.
Empty fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter.
Check all wiring.
See “To Adjust Carburetor” in Service Adjustments
section.
Contact an authorized service center/department.

1.
2.
3.
4.
5.
6.
7.

Dirty air filter.
Bad spark plug.
Weak or dead battery.
Dirty fuel filter.
Stale or dirty fuel.
Loose or damaged wiring.
Carburetor out of adjustment.

1.
2.
3.
4.
5.
6.
7.

Engine valves out of adjustment.

Clean/replace air filter.
Replace spark plug.
Recharge or replace battery.
Replace fuel filter.
Empty fuel tank and refill tank with fresh, clean gasoline.
Check all wiring.
See “To Adjust Carburetor” in Service Adjustments
section.
Contact an authorized service center/department.

Engine will not turn over

1.
2.
3.
4.
5.
6.
7.
8.
9.

Brake pedal not depressed.
Attachment clutch is engaged.
Weak or dead battery.
Blown fuse.
Corroded battery terminals.
Loose or damaged wiring.
Faulty ignition switch.
Faulty solenoid or starter.
Faulty operator presence switch(es).

1.
2.
3.
4.
5.
6.
7.
8.
9.

Depress brake pedal.
Disengage attachment clutch.
Recharge or replace battery.
Replace fuse.
Clean battery terminals.
Check all wiring.
Check/replace ignition switch.
Check/replace solenoid or starter.
Contact an authorized service center/department.

Engine clicks but will not
start

1.
2.
3.
4.

Weak or dead battery.
Corroded battery terminals.
Loose or damaged wiring.
Faulty solenoid or starter.

1.
2.
3.
4.

Recharge or replace battery.
Clean battery terminals.
Check all wiring.
Check/replace solenoid or starter.

Loss of power

1.
2.
3.
4.
5.
6.
7.
8.
9.

Cutting too much grass/too fast.
Throttle in “CHOKE” position.
Build-up of grass, leaves and trash under mower.
Dirty air filter.
Low oil level/dirty oil.
Faulty spark plug.
Dirty fuel filter.
Stale or dirty fuel.
Water in fuel.

1.
2.
3.
4.
5.
6.
7.
8.
9.

Raise cutting height/reduce speed.
Adjust throttle control.
Clean underside of mower housing.
Clean/replace air filter.
Check oil level/change oil.
Clean and regap or change spark plug.
Replace fuel filter.
Empty fuel tank and refill tank with fresh, clean gasoline.
Empty fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter.
Connect and tighten spark plug wire.
Clean engine air screen/fins.
Clean/replace muffler.
Check all wiring.
See “To Adjust Carburetor” in Service Adjustments
section.
Contact an authorized service center/department.

Excessive vibration

10.
11.
12.
13.
14.

Spark plug wire loose.
Dirty engine air screen/fins.
Dirty/clogged muffler.
Loose or damaged wiring.
Carburetor out of adjustment.

10.
11.
12.
13.
14.

15.

Engine valves out of adjustment.

15.

1.
2.
3.

Worn, bent or loose blade.
Bent blade mandrel.
Loose/damaged part(s).

1.
2.
3.

Replace blade. Tighten blade bolt.
Replace blade mandrel.
Tighten loose part(s). Replace damaged parts.

TROUBLESHOOTING POINTS
PROBLEM

CAUSE

CORRECTION

Engine dies when
tractor is shifted
into reverse

1. Turn ignition key to
ROS "ON" position.
See Operation section.

Reverse operation system
(ROS) is not "ON" while
mower or other attachment
is engaged.

Engine continues to run
when operator leaves seat
with attachment clutch
engaged

Faulty operator-safety presence control system.

Check wiring, switches and connections. If not
corrected, contact an authorized service center/
department.

Poor cut - uneven

1.
2.
3.
4.
5.

Worn, bent or loose blade.
Mower deck not level.
Buildup of grass, leaves, and trash under mower.
Bent blade mandrel.
Clogged mower deck vent holes from buildup of
grass, leaves, and trash around mandrels.

1.
2.
3.
4.
5.

Replace blade. Tighten blade bolt.
Level mower deck.
Clean underside of mower housing.
Replace blade mandrel.
Clean around mandrels to open vent holes.

Mower blades will not
rotate

1.
2.
3.
4.

Obstruction in clutch mechanism.
Worn/damaged mower drive belt.
Frozen idler pulley.
Frozen blade mandrel.

1.
2.
3.
4.

Remove obstruction.
Replace mower drive belt.
Replace idler pulley.
Replace blade mandrel.

Poor grass discharge

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.

Engine speed too slow.
Travel speed too fast.
Wet grass.
Mower deck not level.
Low/uneven tire air pressure.
Worn, bent or loose blade.
Buildup of grass, leaves and trash under mower.
Mower drive belt worn.
Blades improperly installed.
Improper blades used.
Clogged mower deck vent holes from buildup of
grass, leaves, and trash around mandrels.

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.

Place throttle control in “FAST” position.
Shift to slower speed.
Allow grass to dry before mowing.
Level mower deck.
Check tires for proper air pressure.
Replace/sharpen blade. Tighten blade bolt.
Clean underside of mower housing.
Replace mower drive belt.
Reinstall blades sharp edge down.
Replace with blades listed in this manual.
Clean around mandrels to open vent holes.

Headlight(s) not working
(if so equipped)

1.
2.
3.
4.
5.

Light switch is “OFF”.
Bulb(s) or lamp(s) burned out.
Faulty light switch.
Loose or damaged wiring.
Blown fuse.

1.
2.
3.
4.
5.

Turn light switch “ON”.
Replace bulb(s) or lamp(s).
Check/replace light switch.
Check wiring and connections.
Replace fuse.

Battery will not charge

1.
2.
3.
4.

Bad battery cell(s).
Poor cable connections.
Faulty regulator (if so equipped).
Faulty alternator.

1.
2.
3.
4.

Replace battery.
Check/clean all connections.
Replace regulator.
Replace alternator.

Loss of drive

1.
2.
3.

Freewheel control in “disengaged” position.
Motion drive belt worn, damaged, or broken.
Air trapped in transmission during shipment
or servicing.

1.
2.
3.

Place freewheel control in “engaged” position.
Replace motion drive belt.
Purge transmission.

Engine “backfires” when
turning engine “OFF”

Engine throttle control not set between half and
full speed (fast) position before stopping engine.

Move throttle control between half and full speed
(fast) position before stopping engine.

TRACTOR - MODEL NO. YTH2448 (279081), PRODUCT NO. 960 13 00-07
SCHEMATIC

BATTERY
SOLENOID
A

RED

AMMETER
(OPTIONAL)

RED

FUSE

STARTER

PTO
(DISENGAGED)

WHITE

S
B
M
A1
G
L A2

WHITE

IGNITION SWITCH

BLACK

CLUTCH / BRAKE
(PEDAL UP)
GRAY

BLACK

SEAT SWITCH
(NOT OCCUPIED)

BLACK

GRAY

BLACK

REVERSE SWITCH

SHORTING CONNECTOR
NOT IN REVERSE

BLACK

ELECTRIC CLUTCH
BLACK
RED

BLACK / WHITE

IGNITION
UNIT
HOUR
METER

BLUE

FUEL SHUT-OFF
SOLENOID

FUEL
LINE

SPARK PLUGS
GAP
(2 PLUGS
ON TWIN CYL. ENGINES)
BLACK

(OPTIONAL)

BLUE

RED

CHARGING SYSTEM OUTPUT
16 AMP DC @ 3600 RPM

(IF SO EQUIPPED)

REGULATOR

YELLOW

ALTERNATOR

28 VOLTS AC @ 3600 RPM
(REGULATOR DISCONNECTED)

ORANGE

LIGHT SW
BLACK

BROWN

BLACK

IGNITION SWITCH
POSITION

CIRCUIT

OFF
RUN/OVERRIDE

M+G+A1
B+A1

RUN
START

B+A1
B + S + A1

“MAKE”

L+A2
02833

NOTE
HEADLIGHTS
YOUR TRACTOR IS
EQUIPPED WITH A SPECIAL
ALTERNATOR SYSTEM.
THE LIGHTS ARE NOT
CONNECTED TO THE
REMOVABLE
NON-REMOVABLE
BATTERY, BUT HAVE THEIR
CONNECTIONS
CONNECTIONS
OWN ELECTRICAL SOURCE.
BECAUSE OF THIS, THE
BRIGHTNESS OF THE LIGHTS
WIRING INSULATED CLIPS
WILL CHANGE WITH ENGINE
NOTE: IF WIRING INSULATED CLIPS
SPEED. AT IDLE THE LIGHTS
WERE REMOVED FOR SERVICING OF
WILL DIM. AS THE ENGINE IS
UNIT, THEY SHOULD BE REPLACED
SPEEDED UP, THE LIGHTS
WILL BECOME THEIR BRIGHTEST. TO PROPERLY SECURE YOUR WIRING.

REPAIR PARTS
TRACTOR - MODEL NO. YTH2448 (279081), PRODUCT NO. 960 13 00-07
ELECTRICAL
22

21
90

43
27

27
40

25
34
16

33
30

50
2

27
D.C

MPE

28
8
y
tter
Ba

_27

RES

193376 ROS

29 46

REPAIR PARTS
TRACTOR - MODEL NO. YTH2448 (279081), PRODUCT NO. 960 13 00-07
ELECTRICAL

KEY
NO.

PART
NO.

DESCRIPTION

1
2
8
16
21
22
24
25
26
27
28
29
30
33
34
40
41
42
43
45
46
50
89
90
91
92
93
94

532 14 49-27
874 76 04-12
532 18 64-91
532 17 61-38
532 18 37-59
532 00 41-52
532 12 47-80
532 14 61-48
532 17 51-58
873 51 04-00
532 14 54-91
532 19 27-49
532 19 33-50
532 14 04-01
532 11 07-12
532 19 33-76
817 72 04-08
532 13 15-63
532 17 88-61
532 12 28-22
532 16 96-35
532 19 61-12
532 16 96-39
532 18 04-49
532 19 02-70
532 19 34-65
532 19 25-40
532 19 18-34

Battery
Bolt Hex Hd 1/4-20 unc x 3/4
Box Battery
Switch Interlock Push-In
Harness Asm Light W/4152j
Bulb Light #1156
Cable Battery 6 Ga. 11" red
Cable Battery 6 Ga. 22" red w/16 wire
Fuse 20 AMP
Nut Keps Hex 1/4-20 unc
Cable Ground black
Switch Seat DP w/ROS
Switch Ign
Key Ign Molded Generic
Switch Light/Reset
Harness Ign.
Bolt 1/4-20 x 1/2
Cover Terminal Red
Solenoid
Ammeter
Hourmeter Snap-In
Switch PTO
Bracket Snap-In Hourmeter
Cover Terminal
Strap Battery
Harness Pigtail Revers Switch
Screw Plastic 10-14 x 2.0
Module Reverse ROS

NOTE: All component dimensions given in U.S. inches.
1 inch = 25.4 mm.

REPAIR PARTS
TRACTOR - MODEL NO. YTH2448 (279081), PRODUCT NO. 960 13 00-07
CHASSIS AND ENCLOSURES
259
212
258

28
212

17
213

217

277

276
10

278

30
214
58
90

31
209

159
280
11

208

9
280
209

278
53

55
278

209

26
142

158

209

144

26
143

144
60
142
209

26
145

208

209

chassis_elite husqy_4

REPAIR PARTS
TRACTOR - MODEL NO. YTH2448 (279081), PRODUCT NO. 960 13 00-07
CHASSIS AND ENCLOSURES

KEY
NO.

PART
NO.

1
2
9
10
11
13
14
17
26
28

532 17 46-19
532 17 65-54
532 19 61-38
872 14 06-08
532 17 49-96
532 18 17-19
817 49 06-08
532 18 99-77
873 80 06-00
532 18 82-69

30
31
37
38
39
53
55
58
60
64
74
90
142
143
144
145
158
159
208
209
212
213
214
217
258
259
276
277
278
280

532 19 48-06
532 13 99-76
817 49 05-08
532 17 57-10
532 17 47-14
532 18 83-73
532 18 83-72
532 18 93-52
872 14 06-06
532 17 49-97
873 68 06-00
532 12 43-46
532 17 57-02
532 18 66-89
532 17 55-82
532 15 65-24
532 16 20-37
532 19 24-04
817 67 06-08
817 00 06-12
532 18 82-67
532 18 99-79
532 18 99-78
532 18 54-36
532 18 99-81
532 18 99-82
532 18 92-74
532 18 92-75
532 19 16-11
817 06 06-16

DESCRIPTION
Chassis Stamping
Drawbar
Dash P/L M
Bolt Carriage 3/8-16 x 1
Panel Dash Lh
Panel Dash Rh
Screw Thdrol 3/8-16 x 1/2
Hood
Nut Lock Hex W/Ins 3/8-16 unc
Grille/Lens Asm.
(Includes Key #'s 212, 258, 259)
Fender Footrest STLT Pnt
Bracket Support Fender
Screw Thdrol 5/16-18 x 1/2 TYT
Bracket Asm Pivot Mower Rear
Bracket Pivot
Bracket Dash LH
Bracket Dash RH
Air Duct Engine
Bolt Rdhd Sqnk 3/8-16 unc x 3/4
Dash Lower STLT
Nut Crownlock 3/8-16 unc
Nut Self-thd Wsh-Hd 1/4
Plate Reinforcement STLT
Bracket Swaybar Chassis
Bracket Pnt Footrest STLT
Rod Pivot Chassis/Hood
Bracket Parking Brake
Cupholder
Screw Thdrol 3/8-16 x 1/2 TYT Bl
Screw 3/8-16 x 3/4
Insert Lens Reflect
Skirt Side LH
Skirt Side RH
Console Fuel Window
Lens RH
Lens LH
Bumper Hood RH
Bumper Hood LH
Screw 10 x 3/4 Single Lead Hex
Screw 3/18-16 x 1

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

REPAIR PARTS
TRACTOR - MODEL NO. YTH2448 (279081), PRODUCT NO. 960 13 00-07
DRIVE

120

263
23
254

63
246
263

245
85

197

66
161

251
169

159 158

59
202

162

198

83
112

247

150

65
17

168

163

82 165 156

166

48
151
51

27
49

39
62
52

120

36 35

37
32

252
29

252

24
19

77
77

78
76

15
1
74 75

drive-hydro.stlt_71

REPAIR PARTS
TRACTOR - MODEL NO. YTH2448 (279081), PRODUCT NO. 960 13 00-07
DRIVE

KEY
NO.

PART
NO.

--------

8
9
10
14
15
16
17
19
21
22
23
24
25
27
28
29
30
32
34
35
36
37
38
39
41
47
48
49
50
51
52
53
55
56
57
59
61
62
63

532 19 25-02
532 17 93-34
876 02 04-16
810 04 04-00
874 49 05-44
873 80 05-00
532 12 61-97
873 80 06-00
532 14 08-45
532 17 81-41
532 19 07-36
873 35 06-00
532 10 68-88
876 02 04-12
532 17 57-65
532 07 16-73
532 16 95-92
874 76 05-12
532 17 55-78
532 12 01-83
819 21 16-16
532 12 49-63
532 17 91-14
872 11 06-22
532 17 55-56
532 12 77-83
532 15 44-07
532 12 32-05
872 11 06-12
873 68 06-00
873 68 05-00
532 10 57-10
532 10 57-09
817 06 06-20
532 17 81-38
532 16 96-91
817 12 06-14
532 12 48-72
532 17 46-07

DESCRIPTION
Transaxle, Peerless LTH2000
(Order Parts From Transaxle Manufacturer)
Rod Shift Fender
Clutch Electric
Pin Cotter 1/8 x 1 CAD
Washer Lock Hvy Helical
Bolt Hex Flghd 5/16-18 Gr. 5
Nut Lock Hex W/Ins. 5/16-18 unc
Washer 1-1/2 OD x 15/32 ID x .250
Nut Lock Hex W/Wsh 3/8-16 unc
Knob
Rod, Brake Hydro
Bracket Anti-Rot
Locknut
Spring, Brake Rod
Pin Cotter 1/8 x 3/4 CAD.
Rod, Parking Brake
Cap, Parking Brake
Bracket, Transaxle
Bolt Hex Hd 5/16-18 unc x 3/4
Shaft, Foot Pedal Nibbed
Bearing, Nylon
Washer
Pin, Roll
Pulley, Idler, Flat Composite
Bolt 3/8-16 x 2-3/4 Gr. 5
Keeper, Belt Idler Fool-Proof
Pulley, Idler, V-Groove
Bellcrank Clutch Grnd Drv Stl
Retainer, Belt
Bolt Carr. SH 3/8-16 x 1-1/2 Gr. 5
Nut
Nut Crown Lock 5/16-18
Link, Clutch
Spring, Return, Clutch
Screw 3/8-16 x 1-1/4
V-Belt, Ground Drive
Keeper, Center Span
Screw 3/8-16 x .875
Cover, Pedal
Pulley, Engine

KEY
NO.

PART
NO.

DESCRIPTION

64
65
66
69
74
75
76
77
78
81
82
83
85
89
95
112
120
150
151
156
158
159
161
162
163
165
166
168
169
197
198
202
245
246
247
251
252
254
263

532 17 39-37
810 04 07-00
532 15 47-78
532 14 24-32
532 13 70-57
532 12 17-49
812 00 00-01
532 12 35-83
532 12 17-48
532 17 81-39
532 16 57-11
819 17 12-16
532 15 03-60
532 19 48-10
532 17 81-34
819 09 12-10
873 90 06-00
532 17 54-56
819 13 32-10
532 16 60-02
532 16 55-89
532 18 39-00
872 14 04-06
873 68 04-00
874 78 04-16
532 16 56-23
817 49 05-10
532 16 54-92
532 16 55-80
532 16 96-13
532 16 95-93
872 11 06-14
532 17 81-22
532 17 81-21
532 18 14-62
817 06 05-16
819 13 16-16
817 00 06-16
817 00 06-12

Bolt Hex 7/16-20 x 4 x Gr. 5
Washer
Keeper Belt Engine Hydro
Screw Hex Wsh Hi-Lo 1/4-1/2 unc
Spacer, Axle
Washer 25/32 x 1-1/4 x 16 Ga.
E-Ring
Key, Square
Washer 25/32 x 1-5/8 x 16 Ga.
Shaft Asm. Cross
Spring Torsion T/A
Washer 17/32 x 3/4 x 16 Ga.
Nut Lock Center 1/4-28
Console, Shift
Control Asm. Bypass Disconnect
Washer 9/32 x 3/4 x 10 Ga.
Nut Lock 3/8-16
Spacer Retainer
Washer 13/32 x 2 x 10 Ga.
Washer Srrted 5/16 ID x 1.125
Bracket Shift Mount
Hub Shift
Bolt Rdhd Sqnk 1/4-20 x 3/4 Gr. 5
Nut Crownlock 1/4-20 unc
Bolt Hex Fin 1/4-20 unc x 1 Gr. 5
Bracket Pivot Lever
Screw 5/16-18 x 5/8
Bolt Shoulder 5/16-18 x .561
Plate Fastening Lt\
Nyliner Snap-In 5/8" ID
Washer Nyliner 7/8 ID x .105
Bolt 3/8-16 x 1-3/4 Gr. 5
Strap Torque Lh
Strap Torque Rh
Link Shift Transaxle
Screw 5/16-18 x 1
Washer
Screw 3/8-16 x 1
Screw Hexwsh Thdr 3/8-16 x 3/4

NOTE:All component dimensions give in U.S. inches.
1 inch = 25.4 mm.

REPAIR PARTS
TRACTOR - MODEL NO. YTH2448 (279081), PRODUCT NO. 960 13 00-07
STEERING ASSEMBLY
38
12
39

37
36
88

91
43

6
65

8
6

87
5

87
3

4
29

43
82

40
43

steering_pl.lt_54

95
8

REPAIR PARTS
TRACTOR - MODEL NO. YTH2448 (279081), PRODUCT NO. 960 13 00-07
STEERING ASSEMBLY

KEY
NO.

PART
NO.

DESCRIPTION

1
2
3
4
5
6
8
10
11
12
13
15
17
29
32
36
37
38
39
40
41
43
46
65
67
68
71
82
87
88
91
94
95

532 16 66-27
532 18 47-06
532 16 98-40
532 16 98-39
532 12 49-31
532 12 17-48
812 00 00-29
532 17 51-21
810 04 06-00
873 94 08-00
532 13 65-18
532 14 52-12
532 17 78-83
817 00 06-12
532 18 05-80
532 15 51-05
532 15 29-27
532 16 66-26
819 18 24-11
873 54 06-00
532 15 99-45
532 12 17-49
532 12 12-32
532 16 03-67
872 11 06-18
532 16 98-27
532 17 51-46
532 16 98-35
532 17 39-66
532 17 51-18
532 17 55-53
819 12 14-14
532 18 89-67

Wheel Steering
Axle
Spindle Asm LH
Spindle Asm RH
Bearing Race Thrust Harden
Washer 25/32 x 1-5/8 x 16 Ga.
Ring Klip #t5304-75
Link Drag
Washer Lock Hvy Hlcl Spr 3/8
Nut Hex Jam Toplock 1/2-20 unf
Spacer Brg Axle Front
Nut Hex Flange Lock
Shaft Asm Strg
Screw 3/8-16 x 3/4
Rod Tie
Bushing Strg
Screw
Insert Cap Strg Wh
Washer 9/16 x 1-1/2 11 Ga.
Nut Crownlock 3/8-24
Adaptor Wheel Strg
Washer 25/32 x 1 1/4 x 16 Ga.
Cap Spindle Fr Top Blk
Spacer Brace Axle
Bolt Rdhd Sq 3/8-16 x 2-1/4
Axle, Brace
Steering Asm
Bracket Susp Chassis Front
Washer Flat .781 x 1-1/2 x .14
Bolt Shoulder 7/16-20
Clip Steering
Washer 3/8 x 7/8 x 14 Ga.
Washer Hardened

NOTE: All component dimensions given in U.S. inches.
1 inch = 25.4 mm.

REPAIR PARTS
TRACTOR - MODEL NO. YTH2448 (279081), PRODUCT NO. 960 13 00-07
SEAT ASSEMBLY
1

8
8

9
14

5
6
22
21

2
24
5

15
11
4
13
17

seat_lt.knob_1

KEY
NO.

PART
NO.

DESCRIPTION

1
2
3
4
5
6
7
8
9
10
11

532 18 87-15
532 14 05-51
871 11 06-16
819 13 16-10
532 14 50-06
873 80 06-00
532 12 41-81
817 00 06-16
819 13 16-14
532 18 24-93
532 16 63-69

Seat
Bracket Pivot Seat 8 720
Bolt Fin Hex 3/8-16 unc x 1
Washer 13/32 x 1 x 10 Ga.
Clip Push-In
Nut Hex w/Ins. 3/8-16 unc
Spring Seat Cprsn 2 250 Blk Zi
Screw 3/8-16 x 1-1/2 Smgml Tap/R Z
Washer 13/32 x 1 x 14 Ga.
Pan Seat
Knob Seat Adj. Wingnut

KEY
NO.

PART
NO.

DESCRIPTION

12
13
14
15
16
17
21
22
24
25

532 17 46-48
532 12 12-48
872 05 04-12
532 12 17-49
532 12 37-40
532 12 39-76
532 17 18-52
873 80 05-00
819 17 19-12
532 12 70-18

Bracket Mounting Switch
Bushing Snap Blk Nyl 50 Id
Bolt Rdhd Sqnk 1/4-2 x 1-1/2
Spacer
Spring Cprsn
Nut Lock 1/4 Lge Flg Gr. 5 Zinc
Bolt Shoulder 5/16-18 unc-2a Blk DA
Nut Hex Lock W/Ins 5/16-18
Washer 17/32 x 13/16 x 12 Ga.
Bolt Shoulder 5/16-18 x 62

NOTE: All component dimensions given in U.S. inches.
1 inch = 25.4 mm

REPAIR PARTS
TRACTOR - MODEL NO. YTH2448 (279081), PRODUCT NO. 960 13 00-07
DECALS
9

4
10

14
8

16
5

15
17
11

KEY
NO.
1
2
3
4
5
6
7
8
9
10

PART
NO.

KEY
NO.

DESCRIPTION

532 17 84-82
532 19 54-87
532 18 89-18
532 18 89-19
532 19 55-49
532 18 09-41
532 19 60-42
532 18 92-43
532 19 63-52
532 15 70-02

Decal Deck Hvy Duty
Decal Panel Side
Decal Hood RH
Decal Hood LH
Decal HP Engine
Decal Hood Cust. Resp.
Decal Operator
Decal Dash
Decal Replacement
Decal Fender Danger

WHEELS & TIRES
1
2

5,8

4,10

3,9
6

PART
NO.

DESCRIPTION

11
12
13
14
15
16
17
------

532 17 52-91
532 18 89-25
532 17 84-55
532 14 50-05
532 19 15-54
532 17 35-87
532 17 35-89
532 17 83-92
532 18 82-52
532 18 82-53
532 13 83-11
532 40 05-09

Decal V-Belt Sch.
Decal Wheel Steering
Decal Deck Caution
Decal Bat Dan/Psn
Decal Fender
Decal, Reflector RH
Decal, Reflector LH
Decal Chassis Disconnect
Pad Footrest LH STLT
Pad Footrest RH STLT
Decal Handle Lft Height Adjust
Manual Owner's (English)

KEY
NO.
1
2
3
4
5
6
7
8
9
10
11
--

PART
NO.
532 05 91-92
532 06 51-39
532 10 62-22
532 05 99-04
532 13 83-36
532 12 49-57
532 12 49-59
532 13 83-37
532 13 84-68
532 12 49-26
532 17 50-39
532 14 43-34

DESCRIPTION
Cap Valve Tire
Stem Valve
Tire F Ts 15 x 6 0 - 6 Service
Tube Front (Service Item Only)
Rim Asm 6"front Silver Service
Fitting Grease (Front Wheel Only)
Bearing Flange (Front Wheel Only)
Rim Asm 8"rear Silver Service
Tire R Ts 20 x 8-8 C Service
Tube Rear (Service Item Only)
Cap Axle Blk 1 50 x 1 00
Sealant, Tire ( 10 oz. Tube)

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
wheel_1

REPAIR PARTS
TRACTOR - MODEL NO. YTH2448 (279081), PRODUCT NO. 960 13 00-07
ENGINE
8
2

14
38

13
81
17

6
5

32
31

37
112
41

33
23

OPTIONAL EQUIPMENT
engine-bs.twin_43

Spark Arrester

REPAIR PARTS
TRACTOR - MODEL NO. YTH2448 (279081), PRODUCT NO. 960 13 00-07
ENGINE

KEY
NO.

PART
NO.

1
2
3

532 19 04-54 Control Th/ch Flag
817 72 04-08 Screw Hex Thd Cut 1/4-20 x 1/2
-------Engine Briggs 446677
(Order Parts From Engine Manufacturer)
532 14 97-23 Muffler
532 15 99-55 Exhaust Tube LH
532 16 05-89 Exhaust Tube RH
532 17 18-77 Bolt 5/16-18 unc x 3/4
532 16 27-97 Shield Heat Muffler
532 16 53-91 Gasket
532 14 84-56 Tube Drain Oil Easy
817 06 06-24 Screw 3/8-16 x 1-1/2
532 16 98-37 Shield Browning/Debris Guard
532 13 27-82 Control Choke
532 13 71-80 Kit Spark Arrestor (Flat Scrn)
532 17 90-22 Tank Fuel
532 18 18-03 Cap Asm Fuel
532 12 34-87 Clamp Hose Black
532 14 21-58 Line Fuel
532 18 16-54 Plug Drain Oil Easy
532 13 92-77 Stem Tank Fuel
817 00 06-12 Screw Hex Wsh Thdr 3/8-16 x 3/4
532 18 39-06 Screw Socket Head 5/16-18 x 1
873 51 04-00 Nut Keps Hex 1/4-20 Starter Nut
532 12 49-52 Bushing

4
5
6
8
10
13
14
17
23
25
29
31
32
33
37
38
41
45
72
81
112

DESCRIPTION

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
For engine service and replacement parts, call the toll free
number for your engine manufacturer listed below:
Briggs & Stratton
1-800-233-3723
Kohler Co.
1-800-544-2444
Tecumseh Products
1-800-558-5402
Honda Engines
1-800-426-7701
Kawasaki
1-800-460-5688

REPAIR PARTS
TRACTOR - MODEL NO. YTH2448 (279081), PRODUCT NO. 960 13 00-07
MOWER LIFT
7
8

2
6

49
52
31

13
51

32
13

49
54

16 17

15
13
54

lift-rh.1piece_21

REPAIR PARTS
TRACTOR - MODEL NO. YTH2448 (279081), PRODUCT NO. 960 13 00-07
MOWER LIFT

KEY
NO.
1
2
3
4
5
6
7
8
11
12
13
15
16
17
18
20
31
32
49
51
52
53
54

PART
NO.
532 15 94-60
532 15 94-71
532 10 57-67
812 00 00-02
819 21 16-21
532 12 01-83
532 12 56-31
532 12 45-26
532 17 53-70
532 17 53-71
532 12 46-70
532 17 55-62
873 35 08-00
532 17 56-89
873 80 08-00
532 16 35-52
532 17 62-05
532 17 59-94
532 14 52-12
819 17 14-16
532 17 53-78
532 17 58-02
532 17 55-60

DESCRIPTION
Wire Asm Inner W/plunger 17 32
Shaft Asm Lift LH Inf Hgt P/L
Pin Groove 1 500 Zinc
E Ring #5133-62
Washer 21/32 x 1 x 21 Ga.
Bearing Nylon Blk 629 Id
Grip Handle
Button Plunger
Link Lift LH
Link Lift RH
Retainer Spring
Plate Asm Suspension Front
Nut Jam Hex 1/2-13 unc
Trunnion Blk Zinc
Nut Lock W/wsh 1/2-13 unc
Retainer Spring
Trunnion Suspension Arm
Nut Lift Link 7/16-20
Nut Hex Flange Lock
Washer 17/32 x 7/8 x 16 Ga.
Arm Suspension Rear LH
Arm Suspension Rear RH
Pin Flange

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

REPAIR PARTS
TRACTOR - MODEL NO. YTH2448 (279081), PRODUCT NO. 960 13 00-07
MOWER DECK
46
132

95
182

roll
er

130

43
42

31
49

121

30
49

30
39

126
98

32
47

50
97

30
111

50
21

110

116

131

117

56
184

133
118

119

100

55
92

54
72
92

24
25

26
29
17

5
15
18

19
14

13
18
11
48
8
mower_deck.48lowcost_stlt_1

183
91
132

REPAIR PARTS
TRACTOR - MODEL NO. YTH2448 (279081), PRODUCT NO. 960 13 00-07
MOWER DECK
KEY
NO.

PART
NO.

DESCRIPTION

1
3
5
6
8
11
13
14
15
16
17
18
19
20
21
24
25
26
27
28
29
30
31
32
33
37
39
42
43
45
46
47
48
49
50
52
54

532 18 03-58
532 13 80-17
532 12 46-70
532 17 80-24
532 17 43-65
532 18 00-54
532 17 43-60
532 17 43-58
532 11 04-85
532 17 44-93
872 11 06-10
872 14 05-05
532 13 28-27
532 17 43-78
873 68 05-00
532 10 53-04
532 17 81-02
532 11 04-52
532 18 17-07
819 11 10-16
532 13 14-91
532 17 39-84
532 18 76-90
532 17 34-36
532 17 83-42
532 17 79-68
532 17 43-75
532 12 20-52
532 17 43-73
532 18 08-06
532 13 77-29
532 18 08-08
532 17 43-68
873 90 06-00
872 11 06-12
532 17 58-20
874 78 06-16

Deck Weldment Mower 48
Bracket Asm., Sway Bar
Retainer Spring
Bar Sway Deck
Bolt, 7/16 Asm. Blade
Blade
Shaft Asm. Mandrel Sealed
Housing Mandrel 48"
Bearing, Ball, Mandrel
Stripper, Mower
Bolt Rdhd Sq Neck 3/8-16 x 1.25
Bolt, Carriage 5/16-18 x 5/8
Bolt, Hex Head, Shoulder 5/16-18
Baffle, Vortex Mower
Nut, Crownlock 5/16-18 unc
Cap, Sleeve
Spring, Torsion
Nut, Push
Shield, Deflector Mower
Washer 11/32 x 5/8 x 16 Ga.
Rod, Hinge
Screw, Thdroll, Washer Head
Washer, Spacer Mower Vented
Pulley, Mandrel
Nut, Flg. Top Lock Cntr. 9/16
Pulley, Idler, Flat
Pulley, Idler, Driven
Spacer, Retainer
Arm, Idler Secondary
Cover, Mandrel Deck
Screw, Thdroll. 1/4-20 x 5/8
V-Belt, Mower, Secondary
V-Belt, Mower, Primary
Nut, Lock 3/8-16 unc
Bolt, Carriage 3/8-16 x 1-1/2 Gr. 5
Pulley Idler Flat 46 Pri. Drive
Bolt Fin Hex 3/8-16 x 1

KEY
NO.
55
56
57
72
91
92
94
95
97
98
99
100
110
111
116
117
118
119
121
126
130
131
132
133
182
183
184
---

PART
NO.
872 14 06-08
532 15 59-86
532 15 69-41
819 13 13-12
532 18 05-35
873 80 06-00
532 17 60-66
532 18 05-34
532 17 85-15
532 17 94-79
532 18 99-93
872 11 06-16
532 17 50-16
532 17 46-10
532 18 42-19
532 17 48-73
873 93 06-00
819 12 14-14
532 17 43-71
532 17 43-72
817 00 06-16
819 13 16-06
817 00 06-12
872 11 05-06
532 17 91-27
532 16 35-52
532 17 39-79
532 17 43-57

DESCRIPTION
Bolt Rdhd Sqnk 3/8-16 x 1
Bar Pnt Adjusting Wheel Gauge
Pin Head Rivet
Washer 13/32 x 13/16 x 12
Bracket, Asm Noseroller, RH 48
Nut Lock Hex w/Ins 3/8-16
Roller, Nose 48"
Bracket, Asm Noseroller LH 48
Washer Hardened
Spring Primary Drive
Pulley Idler "V"
Bolt RDHD Sqnk 3/8-16 unc x 2
Arm Spring Secondary
Arm Spring Fixed Tension
Bolt, Shoulder
Gauge Wheel
Nut, Centerlock 3/8-16 unc
Washer 3/8 x 7/8 x 14 Ga.
Spring Secondary Drive
Arm, Idler, Primary Deck
Screw 3/8-16 x 1.0
Washer 13/32 x 1 x 6 Ga.
Screw 3/8-16 x 3/4
Bolt Rdhd Sqnk 5/16-18 unc x 3/4
Rod Roller Nose
Retainer Spring
Keeper Belt Idler
Mandrel Assembly (Includes Housing, Shaft and Shaft Hardware
Only-Pulley Not Included)
532 18 99-06 Replacement Mower, Complete
(Std Deck-Order Separately Nose
Roller Components Key Nos. 91,
94, 95, 132, 182-183)

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION

FOL
D AL
ONG
THIS
DO T
IS A
TED
15 D
LINE
EGR
EE S
LOP
E

ONLY RIDE UP AND DOWN HILL,
NOT ACROSS HILL

15 DEGREES MAX.

WARNING: To avoid serious injury, operate your tractor up and
down the face of slopes, never across the face. Do not mow
slopes greater than 15 degrees. Make turns gradually to prevent
tipping or loss of control. Exercise extreme caution when
changing direction on slopes.
1. Fold this page along dotted line indicated above.
2. Hold page before you so that its left edge is vertically parallel to a tree
trunk or other upright structure.
3. Sight across the fold in the direction of hill slope you want to measure.
4. Compare the angle of the fold with the slope of the hill.

WARRANTY STATEMENT
SECTION 1: LIMITED WARRANTY

SECTION 4: EXCEPTIONS AND LIMITATIONS

Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser
to be free from defects in material and workmanship from the date of purchase for the “Warranty Period” of the
product as set forth below:
Lifetime Warranty: All tiller tines against breakage, trimmer shafts, ignition coils and modules on hand held
product.

This warranty shall be inapplicable to defects resulting from the following:
(1)Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust,
corrosion, or any adverse reaction due to incorrect storage or use habits;
(2)Failure to operate or maintain the unit in accordance with the Owner’s/Operator’s manual or instruction sheet furnished by Husqvarna;
(3)Alterations or modifications that change the intended use of the product or affects the product’s performance, operation, safety, or durability, or causes the product to fail to comply with any applicable
laws; or:
(4)Additional damage to parts or components due to continued use occurring after any of the above.

3 Year Warranty: Spindles (on Zero Turn Riders and Commercial Walk-Behinds)
2 Year COMMERCIAL-Warranty: Husqvarna Commercial Turf Equipment—zero turn riders, wide area walks,
and ground engaging commercial equipment.
2 Year NON-COMMERCIAL Warranty: Automatic Mower, Riding lawn mowers, yard and garden tractors, walk
behind mowers, tillers, chain saws, trimmers, brushcutters, clearing saws, snow blowers, handheld blowers,
backpack blowers, hedge trimmers, electrical products and power-assist collection systems for noncommercial, nonprofessional, noninstitutional or nonincome producing use, except as herein stated.
Emission control system components necessary to comply with CARB-TIER-II and EPA regulations, except
for those components which are part of engine systems manufactured by third party engine manufacturers for
which the purchaser has received a separate warranty with product information supplied at time of purchase.
1 Year Warranty: Power cutters, stump grinder, pole pruners and pole saws for non-commercial, non-professional, non-institutional or non-income producing use. All trimmers, brushcutters, clearing saws, hovering
trimmers, stick edgers, backpack blowers, hand held blowers, hedge trimmers, power-assist collection systems
used for commercial, institutional, professional or income producing purposes or use.

Batteries have a one-year prorated limited warranty with 100% replacement during the first 6 months.
90 Day Warranty: Automatic Mower, Chain saws, power cutters, stump grinders, pole saws, pole pruners,
snow throwers, model series 580 & 600 walk-behind mowers and commercial turf equipment or any Husqvarna
product used for commercial, institutional, professional, or income producing purposes or use except as otherwise provided herein.
Husqvarna Safety Apparel carries a 90-day warranty from the date of the customer’s original purchase for
defects in material and workmanship. Normal wear, tear or abuse is not covered under warranty. Product must
be returned to Charlotte with a warranty claim form. All care and maintenance instructions must be followed
as stated by the manufacturer on the care label. The fit of the protective apparel/boot is not covered under
warranty.
30 Day Warranty: Replacement parts, accessories including bars and chains, tools and display items.

SECTION 2: HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY
Husqvarna will repair or replace defective components without charge for parts or labor if a component fails
because of a defect in material or workmanship during the warranty period.

SECTION 3: ITEMS NOT COVERED BY THIS WARRANTY
The following items are not covered by this warranty:
(1)Normal customer maintenance items which become worn through normal regular use, including, but
not limited to, belts, blades, blade adapters, bulbs, filters, guide bars, lubricants, rewind springs, saw
chain, spark plugs, starter ropes and tines;
(2)Natural discoloration of material due to ultraviolet light;
(3)Engine and drive systems not manufactured by Husqvarna; these items are covered by the respective
manufacturer’s warranty as provided in writing with the product information supplied at the time of purchase; all claims must be sent to the appropriate manufacturer;
(4)Lawn and garden attachments are covered by a third party which gives a warranty, all claims for warranty should be sent to the manufacturer; and
(5)Emission Control System components necessary to comply with CARB-TIER-II and EPA regulations
which are manufactured by third party engine manufacturer.

REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF
THE PURCHASER. HUSQVARNA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THESE PRODUCTS EXCEPT
TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THESE PRODUCTS IS LIMITED IN DURATION TO
THE WARRANTY PERIOD AS DEFINED IN THE LIMITED WARRANTY STATEMENT. HUSQVARNA RESERVES THE RIGHT TO CHANGE OR IMPROVE THE DESIGN OF THE PRODUCT WITHOUT NOTICE,
AND DOES NOT ASSUME OBLIGATION TO UPDATE PREVIOUSLY
MANUFACTURED PRODUCTS.
Some states do not allow the exclusion of incidental or consequential damages, or limitations on how long
an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state.

SECTION 5: CUSTOMER RESPONSIBILITIES
The product must exhibit reasonable care, maintenance, operation, storage and general upkeep as written
in the maintenance section of the Owner’s/Operator’s manual. Should an operational problem or failure occur,
the product should not be used, but delivered as is to an authorized Husqvarna dealer for evaluation. Proof
of purchase, as explained in section 6, rests solely with the customer.

SECTION 6: PROCEDURE TO OBTAIN WARRANTY CONSIDERATION
It is the Owner’s and Dealer’s responsibility to make certain that the Warranty Registration Card is properly
filled out and mailed to Husqvarna Forest & Garden Company. This card should be mailed within ten (10) days
from the date of purchase in order to confirm the warranty and to facilitate post-sale service.
Proof of purchase must be presented to the authorized Husqvarna dealer in order to obtain warranty service. This proof must include date purchased, model number, serial number, and complete name and address
of the selling dealer.
To obtain the benefit of this warranty, the product believed to be defective must be delivered to an authorized Husqvarna dealer in a timely manner, no later than thirty (30) days from date of the operational
problem or failure. The product must be delivered at the owner’s expense. Pick-up and delivery charges are
not covered by this warranty. An authorized Husqvarna dealer can be normally located through the “Yellow
Pages” of the local telephone directory or by calling 1-800-HUSKY62 for a dealer in your area.

HUSQVARNA
7349 Statesville Road
Charlotte, NC 28269
531 83 81-23

2002

532 40 05-09 08.09.05 rad

Printed in U.S.A.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Create Date                     : 2005:08:09 19:28:00Z
Modify Date                     : 2007:06:04 15:54:37-04:00
Page Count                      : 48
Creation Date                   : 2005:08:09 19:28:00Z
Mod Date                        : 2007:06:04 15:54:37-04:00
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : Husqvarna
Metadata Date                   : 2007:06:04 15:54:37-04:00
Title                           : OM, YTH 2448 (917.279081), 960130007, 2005-08, Ride Mower
Creator                         : Husqvarna
Page Mode                       : UseOutlines
Page Layout                     : OneColumn

EXIF Metadata provided by EXIF.tools

Husqvarna Yth 2448 Users Manual OM, (917.279081), 960130007, 2005 08, Ride Mower

YTH 2448 to the manual 47d65c1c-e771-4dbf-b9a6-908c6d63443d

Navigation menu

Versions of this User Manual:

Views

Navigation