Hussman Igsv Ascs 0303 Users Manual 6.5

IGSV-ASCS-0303 to the manual ba921330-dada-4896-abd4-d1e31fac9116

2015-02-05

: Hussman Hussman-Igsv-Ascs-0303-Users-Manual-403466 hussman-igsv-ascs-0303-users-manual-403466 hussman pdf

Open the PDF directly: View PDF .
Page Count: 40

/Chino

ASCS

DELI, MEAT, FISH SERVICE CASE REV.0303

Installation

& Operation

Manual

ASCS

DELI, MEAT, FISH

SERVICE CASE

P/N IGSV-ASCS-0303

INSTALLATION & OPERATION GUIDE

IGSV-ASCS-0303

/Chino

A publication of

Hussmann® Chino

13770 Ramona Avenue • Chino, California 91710

(909) 628-8942 FAX

(909) 590-4910

(800) 395-9229

Keep this booklet with the case at all times for future reference.

THIS BOOKLET CONTAINS INFORMATION ON:

ASCS refrigerated, service deli, meat, fish mechandiser

SHIPPING DAMAGE

All equipment should be thoroughly examined for shipping

damage before and during unloading.

This equipment has been carefully inspected at our factory

and the carrier has assumed responsibility for safe arrival.

If damaged, either apparent or concealed, claim must be

made to the carrier.

APPARENT LOSS OR DAMAGE

If there is an obvious loss or damage, it must be noted on

the freight bill or express receipt and signed by the carrier’s

agent; otherwise, carrier may refuse claim. The carrier will

supply necessary claim forms.

CONCEALED LOSS OR DAMAGE

When loss or damage is not apparent until after equipment

is uncrated, a claim for concealed damage is made. Make

request in writing to carrier for inspection within 15 days,

and retain all packaging. The carrier will supply inspection

report and required claim forms.

SHORTAGES

Check your shipment for any possible shortages of material.

If a shortage should exist and is found to be the

responsibility of Hussmann Chino, notify Hussmann Chino.

If such a shortage involves the carrier, notify the carrier

immediately, and request an inspection. Hussmann Chino

will acknowledge shortages within ten days from receipt

of equipment.

HUSSMANN CHINO PRODUCT CONTROL

The serial number and shipping date of all equipment has

been recorded in Hussmann’s files for warranty and

replacement part purposes. All correspondence pertaining

to warranty or parts ordering must include the serial

number of each piece of equipment involved, in order to

provide the customer with the correct parts.

The Hussmann warranty is printed on the back

of this guide.

General Instructions

Ta b l e of Contents

General Instructions ................................................. 2

Cut & Plan Views ....................................................... 3

Installation ................................................................. 3

LEVELING.............................................................................................................. 4

Plumbing .................................................................... 6

WASTE OUTLET AND P-TRAP .............................................................................. 6

Manifold Flush System ............................................. 7

Humidity System ...................................................... 9

Refrigeration ............................................................. 10

T-STAT LOCATION .................................................................................................. 11

Electrical .................................................................... 12

WIRING COLOR CODE ......................................................................................... 12

ASHRAE COLOR CODE .......................................................................................... 12

Finishing Touches ...................................................... 13

JOINT TRIM........................................................................................................... 13

User Information ...................................................... 14

STOCKING.............................................................................................................. 14

CASE CLEANING.................................................................................................... 14

NON-GLARE GLASS ............................................................................................... 15

PLEXIGLASS and ACRYLIC CARE ........................................................................... 15

REPLACING FLUORESCENT LAMPS ....................................................................... 16

Maintenance .............................................................. 16

TIPS and TROUBLESHOOTING .............................................................................. 16

LIFT UP GLASS ..................................................................................................... 17

Electrical and Refrigeration Specifications ............ 19

Electrical Schematics ............................................... 20

Appendices ................................................................ 35

APPENDIX A. – Temperature Guidelines ............................................................ 35

APPENDIX B. – Application Recommendations.................................................. 35

APPENDIX C. – Field Recommendations -......................................................... 35

APPENDIX D. – Recommendations to user - .................................................... 36

Rev.0303

Cut & Plan Views

Installation

LOCATION

The refrigerated merchandisers have been designed for

use only in air conditioned stores where temperature and

humidity are maintained at or below 75°F and 55% relative

humidity. DO NOT allow air conditioning, electric fans,

ovens, open doors or windows (etc.) to create air currents

around the merchandiser, as this will impair its correct

operation.

Product temperature should always be maintained at a

constant and proper temperature. This means that from

the time the product is received, through storage,

preparation and display, the temperature of the product

must be controlled to maximize life of the product.

UNCRATING THE STAND

Place the fixture as close to its permanent position as

possible. Keep in place, attached case until ready to set/

bolt to adjoining case.

TIGHTEN GLASS SCREWS

Tighten screws along clamshell located on the underside

of glass before placing unit into operation.

EXTERIOR LOADING

These models have not been structurally designed to

support excessive external loading. Do not walk on their

tops. This could cause serious personal injury and damage

to the fixture.

SETTING AND JOINING

The sectional construction of these models enable them

to be joined in line to give the effect of one continuous

display. A joint trim kit is supplied with each joint.

ASC with

22 1/2º Wedge

ASC with 22 1/2º Wedge

ASCS

Single Deck Refrigerated Service

Scale = 1/2"

34"

11"

45"

"4"

45"

CASE FRONT

11"

ASCS

Plan View

Scale = 1/4"

DRAIN

MECHANICAL

STUB UP AREA

19" X 19"

WATER, ELEC.

& REFRIG.

MECHANICAL

STUB UP AREA

19" X 19"

8'-2"

(VARIABLE LENGTHS)

1" 1"

IGSV-ASCS-0303

adjustable legs to allow for leveling.

NOTE: The mock pedestal option supplies panels that

clamp on to adjustable legs.

2. Set first case over the highest part of the floor and

adjust legs so that case is level. Remove side and back

leg braces after case is set and joined.

3. Set second case within one foot (1’) of the first case,

and remove end shipping support. Keep the supports

along the length of the case and far end of case. Level

case to the first using the instructions in step one.

4. Apply masking tape 1/8" in from end of case on inside

and outside rear mullion on both cases to be joined.

5. Apply liberal bead of case joint sealant (butyl) to first

case. Sealant area is shown using a dotted line in

illustration in Step 8. Apply heavy amount to cover

entire shaded area.

DO NOT USE PERMAGUM

Butyl

ASCS

Butyl Locations

LEVELING

Important! It is imperative that cases be

leveled from front to back and side to side

prior to joining. A level case is necessary to

insure proper operation, water drainage,

glass alignment, and operation of the hinges

supporting the glass. Leveling the case

correctly will solve all hinge operation and

glass alignment problems.

NOTE: A. To avoid removing concrete flooring, begin lineup

leveling from the highest point of the store floor.

B. When wedges are involved in a lineup, set them first.

All cases were leveled and joined prior to shipment to

insure the closest possible fit when cases are joined in the

field. When joining, use a carpenters level and adjust legs

accordingly. The legs on the ASCS are adjustable and do

not require shims. Simply screw the leg up or down to

adjust height.

1. Using case blueprints, measure off and mark on the

floor the exact dimensions of where the cases will sit.

Snap chalk line for front and back positions of base rail

or pedestal. Mark the location of each joint front and

back. Find the highest point throughout the lineup.

FLOORS ARE NORMALLY NOT LEVEL! Determine

the highest point of the floor; cases will be set off this

point. All cases in the entire lineup must be brought

up to the highest level of the case sitting at the highest

point in the lineup. This may be done a few different

ways. 1) Walk the floor looking for any mounds or dips.

2) Use a string level. 3) Use a transit. If a wedge is used

in the middle of a lineup, the wedge must be set on the

highest point on the floor FIRST, with the rest if the

lineup being leveled from it. The ASCS case has

Installation (continued)

Rev.0303

It is the contractor's responsibility to install

case(s) according to local construction and

health codes.

6. Slide second case up to first case snugly. Then level

second case to the first case so glass front, bumper and

top are flush.

Do not use bolts to pull cases together!

7. To compress butyl at joint, use two Jurgenson wood

clamps. Make sure case is level from front to back and

side to side on inside bulkheads at joint.

8. Attach sections together via the bolts pictured in the

illustration below.

1/4” Binding Post

5/16” Bolts

ASCS

Bolt Locations

9. Apply bead of butyl to top of bulkheads and slip on

stainless steel bulkhead cap. Also apply silicone to

seam between overhead light tubes.

10. Use finger to smooth silicone as thin as possible at

masking tape on inside and outside of rear mullion

Installation (continued)

(apply additional silicone if necessary). Remove tape

applied on line #4.

11. Remove front, back and end shipping braces.

INSIDE REFRIGERATED WEDGES

Line up taper pins with holes on adjoining case. Turn

camlock to lock in. Two camlocks are located at the rear

of the case behind the air discharge and behind the lower

electrical raceway access panel. Bolt the wedge into the

adjoining case in the front. If the adjoining case is

refrigerated, the bolt is located under the pans in the front.

When the adjoining case is a hot case, the cases are bolted

together by mans of a bracket located behind the front

panel. Remove the front panel by lifting it up and out..

COMMON END BETWEEN UNLIKE CASES

AND HOT CASES

Bolt the end onto the case using the bolts provided in

predrilled holes behind the front of the panel through the

bracket provided and in the rear behind the rear access

panel on the bottom Common ends between refrigerated

cases are also bolted together behind the air discharge

panel. Remove the discharge panel by lifting up and out.

Hot cases are only bolted in two places, in the rear of the

case, behind the access panel, and in the front of the case

behind the front panel.

OUTSIDE REFRIGERATED WEDGE:

Taper pin and camlock locations are the same as a standard

case.

INSIDE DRY WEDGES

Bolt the wedge into the sides of the adjoining case. Use

the bolts provided

INSIDE PEDESTAL WEDGES

Set the wedge on adjoining case’s mounting brackets

located at the base of the unit, and bolt down. Drive screws

provided through the sides of the wedge (4 screws per

side), accessible through the back of the wedge.

1. Secure the joint backer located behind the cart

bumper support at the joints. To adjust the front panel.

Loosen the screws holding the bumper on the case on

either side the joint, and slide the extrusion to the

center of the joint.

2. Starting from a center case in a lineup or wedge, align

the front panels. Front panels can be loosened and

adjusted laterally by loosing the screws holding the

case bumper channel.

IGSV-ASCS-0303

Installation (cont.)

Plumbing

WASTE OUTLET AND P-TRAP

The waste outlet is located off the center of the case on

one side allowing drip piping to be run lengthwise under

the fixture.

A 1-1/2" P-trap and threaded adapter are supplied with

each fixture. The P-trap must be installed to prevent air

leakage and insect entrance into the fixture.

NOTE: PVC-DWV solvent cement is recommended.

Follow the Hussmann’s instructions.

INSTALLING CONDENSATE DRAIN

Poorly or improperly installed condensate drains can

seriously interfere with the operation of this refrigerator,

and result in costly maintenance and product losses. Please

follow the recommendations listed below when installing

condensate drains to insure a proper installation:

1. Never use pipe for condensate drains smaller than the

nominal diameter of the pipe or P-trap supplied with

the case.

2. When connecting condensate drains, the P-trap must

be used as part of the condensate drain to prevent air

leakage or insect entrance. Store plumbing system

floor drains should be at least 14" off the center of the

case to allow use of the P-trap pipe section. Never use

two water seals in series in any one line. Double P-

traps in series will cause a lock and prevent draining.

3. Always provide as much down hill slope (“fall”) as

possible; 1/8" per foot is the preferred minimum. PVC

pipe, when used, must be supported to maintain the

1/8" pitch and to prevent warping.

4. Avoid long runs of condensate drains. Long runs make

it impossible to provide the “fall” necessary for good

drainage.

5. Provide a suitable air break between the flood rim of

the floor drain and outlet of condensate drain. 1" is

ideal.

6. Prevent condensate drains from freezing:

a. Do not install condensate drains in contact with

non-insulated suction lines. Suction lines should be

insulated with a nonabsorbent insulation material

such as Armstrong’s Armaflex.

b. Where condensate drains are located in dead air

spaces (between refrigerators or between a

refrigerator and a wall), provide means to prevent

freezing. The water seal should be insulated to

prevent condensation.

ARM STRUT

GUSSET

WEDGE BRACKET

Corner wedges are attached via front and rear camlocks.

Use a 7mm Allen wrench to turn the locks. Do not

overtighten! Join the top by using a joint bracket (included

in joint kit) with 3/8" bolts.

Rev.0303

Manifold Flush System

GENERAL DESCRIPTION

The flush system generates a high pressure water stream

meant to flush most residue buildup from the bottom of

the manifold chamber. This is the area that residue builds

and expands. Frequency of this periodic maintenance will

vary depending on water mineral content and sanitary

conditions.

MANUAL FLUSH SYSTEM

Water valve is located on the outside of the case, in the

rear, on the left hand side as viewed from the rear.

AUTOMATIC FLUSH SYSTEM

Electrical components are located within the electrical

raceway. Electrical components in this area are 115V AC.

Step-down transformer is located in the wireway, and is

controlled by pump switch. Water flow for flush system is

rated at 0.25 GPM at 60 PSI water pressure. Flush nozzle

located in the rear of the case.

BASIC SYSTEM OPERATION:

1. Filtered water is supplied to the 115V solenoid valve.

2. At a time of day determined by you, the 115V time

clock will energize the solenoid for two (2) minutes.

PROGRAMMING THE TIMER

The circular keypads are positioned to provide a sequential

[at for programming. Starting the Prog. button to select a

program clockwise to ON/OFF, h for hour, m for minute,

and finally Day to select the day for days of the week you

wish the flush to operate on. If one of these selections is

omitted, the control will flash when the clock or program

key is depressed. The missing entry must be completed

before the programming can resume.

•A program consists of

1. ON/OFF

2. Hour and minute

3. Day or multiple days on which it is to occur.

•Res. is the reset key and will erase the current

program.

•The ±h key adjusts the set clock time for daylight

savings time.

•Military time (24 hr clock) or 12 hour clock may be

selected by pressing and holding the h key while

depressing the ±h key.

•A flashing light indicated a missing selection in the

program or a low battery. Check to make sure the

timeclock’s program is complete (ON/OFF, time, and

days)

NOTE: If the h and m keys are held down longer than 2

seconds, the numbers will advance rapidly. Press and hold

the (2) day during the following: (If Daylight Savings Time is

In effect, press ±1h first).

1. Press the Prog. key.

1 2 4 5 6 7

AM– –:– –

will appear in display.

2. Press the key between ON/OFF. The word ON will

appear.

3. Press h to select hour for initial system startup.

4. Press m to select the minute the system starts up (30

for 10:30)

5. Select the days desired with the Day key.

1. If the program is to occur every day of the week,

ignore Day and press Prog. key to advance to next

program.

2. If specific, 7 day time control is desired, press Day

and 1-5 will appear for Mon. - Fri. Pressing Day

again will display 6,7 for Sat. and Sun.

6. Press the key between ON/OFF to select the cycle

termination time. The word OFF will appear.

7. Press h to select hour the system terminates.

8. Press m to select the minute the system terminates.

9. Repeat with the days.

10. Press Prog. key and repeat steps 2 thru 11 for

additional defrost schedules.

11. After programming press clock key to enter run

mode.

NOTE: If the days are flashing, it indicates the day of the week was not set

when setting the time. The timer cannot be programmed unless the day of

the week is entered.

Ref.

Prog.

Day

hr.

Mo Tu We Sa

Th Su

GRÄSSLIN

On Off

START UP:

1. Manually move time clock to initiate a flush cycle.

2. Observe that flush nozzle is spraying down center of

manifold chamber.

3. Set clock to correct time of day.

4. Set trip pins to the “time of day system is to flush”

(NOTE: Two [2] flushes per day!)

IGSV-ASCS-0303

ELBOW 90°

1/4" NPT x 1/4" NPT

# 225-01-0336 COMPRESSION FITTING

PVC - 1/4" NPT x 1/2" OD

# 225-01-1323

CASE BOTTOM LINER

(16 GA. GALV)

INSULATION @

CENTER OF CASE

(FRONT TO BACK)

POLYURETHANE COAT

PERMAGUM SEAL

WASHER # 038222

NOZZLE - MONARCH

Model #: H-545-R2-0.72-360 303SS

# 225-01-2004-SS

USE WASHERS

(IF REQUIRED)

1/2" OD POLY TUBING

# 225-01-0003

(HOCKEY-POCK SPACER)

NIPPLE (1/2) 3" LONG

304 SS PIPE

# 225-01-0602

These two components

are now assembly

part # 225-01-0603

Nozzle and Components with Part Numbers

ELBOW 90°- BRASS

1/4" NPT x 1/4" NPT

# 225-01-0336

COMPRESSION FITTING

PVC - 1/4" NPT x 1/2" OD

# 225-01-1323

NOZZLE - MONARCH

Model #: H-545-R2-0.72-360

303SS

# 225-01-2004-SS

1/2" OD POLY TUBING

# 225-01-0003

WASHER / PIPE ASSEMBLY

304 STAINLESS

# 225-01-0603

COMPRESSION FITTING

PVC - 1/2" OD x 1/2" NPT

# 225-01-1322

SOLENOID VALVE

ALCO 222CB- B- B-AMS

# 225-01-1340

UNION TEE COMPRESSION

PVC - 1/2" OD x 1/2" OD

# 225-01-1324

COMPRESSION FITTING

PVC - 1/2" OD x 1/2" NPT

# 225-01-1322

COMPRESSION FITTING

PVC - 1/2" OD x 1/2" FPT

# 225-01-1327

(FIELD CONNECTION)

HAND BALL VALVE

PVC - 1/2" FPT - FULL

BORE - # 225-01-2122

IN-LINE STRAINER - CLEAR

BOWL - NYLON 1/2" MPT

TEEL 2P131 # 225-01-2133

LEAVE AT LEAST 10'

FOR FIELD CONNECTION

Nozzle count to change

according to case length.

WATER PRESSURE

REGULATOR

SPRAY SYSTEMS CO. 6815-1/2

# 225-01-1403

Water Flush Fittings with Part Numbers

SOLENOID VALVE BODY

ALCO 222CB- B-

# 225-01-1340

SOLENOID COIL

ALCO- AMS

COMPRESSION FITTING

PVC - 1/2" OD x 1/2" NPT

# 225-01-1322

COMPRESSION FITTING

PVC - 1/2" OD x 1/2" NPT

# 225-01-1322

BRACKET

# 038244

#5-32 SELF

TAP SCREW

#5-32 SELF

TAP SCREW

#5-32 SELF

TAP SCREW

BRACKET

# 038244 #5-32 SELF

TAP SCREW

Solenoid Valve and Part Numbers

Rev.0303

Humidity System

GENERAL DESCRIPTION

One contributor to the spoilage of fresh meats is

dehydration, which causes loss in weight and volume

(shrinkage) and product discoloration. As the refrigeration

system removes heat from the case, it also removes critical

moisture from the air, and any unwrapped products in the

case. The Humidity System replaces the moisture in the

air, in order to compensate for the moisture taken by the

refrigeration system, and disposed of down the drain line.

The system is built into the discharge plenum, and mixes

moisture laden air with refrigerated air before the air is

passed through - and around the product.

The system is constructed almost entirely of PVC pipe,

and uses air that is subcooled to approximately the same

temperature as the case. The sub-cooling of air inhibits

the formation of growth found to be a problem in other

humidification systems. Maintenance is almost unnecessary

if you follow a few simple rules:

1. Keep the case clean.

2.Keep the water filter clean, and change it every six

to twelve months or sooner, depending on the kind of

water found in your area.

3. Flush the header every six (6) months, by loosening

the connecting “L”, then removing it from the case, and

flushing with a hose.

**IMPORTANT INFORMATION**

The ASCS is capable of maintaining superb product quality

with the installation of the proper controlling devices. These

devices should be set according to the Hussmann’s

specifications. The humidity system should be properly

maintained. Incorrect settings and failure to maintain the

humidity system will result in short product life. Below

are a few guidelines for optimum performance and product

life:

•Set thermostat to cut in at the discharge temperature

designated in the case specifications section of the

appropriate installation guide or spec. sheet. Maintain

the recommended product temperature for Deli,

Meat, and Fish. DO NOT set temperature too cold, as

this causes product dehydration.

•Temperatures should be achieved by means of a T-Stat

and Suction Solenoid at each case. DO NOT use EPR

valves, Liquid Line Solenoids, or electronic control

devices of any kind. These controls allow temperature

swings that cause dehydration and excessive energy

consumption.

•Set defrost cycles as listed in the Case Specifications

Data for your particular case. The number of defrosts

per day should never change. The duration of the

defrost cycle may be adjusted to meet conditions

present at your location.

•Clean humidity system a minimum of every 90 days for

proper system operation.

•Work and rotate product - not to exceed a four (4)

hour period.

•At night, turn off case lights, and cover unwrapped

product with moistened cheesecloth or fabric towels.

•Keep meat holding box at 32°F.

•Keep meat prep room refrigerated at 55°F.

•Meat Bloom Box (if applicable) should be at 36°F.

•Meat must enter the case at 40°F or below. Product

deteriorates rapidly above 40°F.

•Clean, sanitary conditions are required throughout the

meat holding, prep, and work areas.

•Do not display product directly within the air

discharge

•Turn and rotate meat. The blood works down through

the meat over time, which causes the top surface to

discolor and dehydrate. Turn meat 3-4 times per day.

•It is not required to remove product from case

overnight. Turn off case lights, and cover product with

moistened cheesecloth or fabric towel. This helps slow

down product dehydration, by taking moisture from

the cloth and not the product. This is an old method

used by meat shops for many years, as it extends

product life.

•Cold coils remove heat and moisture from the case

and deposit this as frost onto the coil. Thus a defrost

is required to remove this frost. Our humidity system

induces moisture into the case, and helps slow down

the dehydration process. The only other moisture in

the case is that which is in the product. A single level

of meat will dry out faster than a fully loaded case with

3-4 levels of meat.

•The colder the case, the faster the product loses its

moisture and shelf life. It is very important to maintain

a constant, even, correct, product temperature.

HUMIDIFICATION SYSTEM HOOKUPS

Remove the raceway panel on the lower back of the case.

The pre-piped water shut-off valve and the water filter

are located on the left hand side of the case. The water

line (which is a 1/4" OD copper fitting) can be connected

to the ball shut-off valve, by means of a compression fitting

(supplied). The line should be one size larger than the supply

line. The line can then be run from one case to another

from within the raceway(s) using Tee connectors. Before

connecting the water to the humidity system, it is best to

IGSV-ASCS-0303

Humidity System (cont.)

purge the line to flush any debris that may clog the water

filter. If the water line requires purging after the cases are

hooked together, it is not necessary to check each one.

Simply shut ball valves to each humidity system, remove

the water line from the last case in the flow, and purge. By

doing this as a precautionary measure, you may avoid

problems and repeat servicing.

START-UP

Turn on the fan circuit. Check to see if the fan for the

humidity system is running. Remove the right hand bottom

pan (when facing the front of the case), then the TXV cover.

The fan is located up against the right hand side of the

case, as viewed from the front, under the fan plenum (see

diagram). View the blade, and make sure the fan rotation

agrees with the air flow arrows. Turn on the water, by

turning the ball valve in the direction of the flow (OFF is

at 90° to the direction of flow).

After a few minutes, check the spray header by sliding the

honeycomb to the left to expose the discharge tube located

on the right hand side of the case (when viewed from the

rear), by lifting the 4'-0" section of honeycomb with both

ends, until the bottom clears. Pull up and set aside. The

spray header will be exposed. Grasp the header and pull it

loose from the 90° “L” until you see the misting nozzle,

which should be spraying. If not, check the following:

1. Make sure the water is feeding the nozzle.

2. Remove the nozzle, and purge the water.

3. Check strainer at entrance to nozzle.

Reinsert the header into the 90° “L”, making sure that the

nozzle is in the center of the pipe when totally inserted,

and the holes in the header are facing the front of the case

at a level angle.

The discharge tube can easily be pulled to service.

MAINTENANCE

•Clean humidity system a minimum of every 90 days for

proper system operation.

HAGO-M1 NOZZLE

225-01-3221

WATER

SUPPLY

SPRAY HEADER

RUNS LENGTH OF CASE

WATER FILTER

3 STAGE #00015

225-01-2026

3" AXIAL FAN

225-01-2026

2ND FAN USED

IN 12' CASE

REAR INTERIOR WALL OF CASE

VIEWED FROM FRONT

BALL VALVE

HAMMON

225-01-2026

1/4" 100 X 1/8FPT

SW ADAPTER

225-01-2089A

1/4" OD X 1/8" FPT

SW ADAPTER

225-01-3059

1/8" MPT X 1/4" COMP

PVC ADAPTER

225-01-3059

1/4"MPT X 1/4" COMP PVC ADAPTER

225-01-2026

1/4"MPT X 1/4" OD

COMP ADAPTER

225-01-1312

PAN AND ACCESS PANEL

1/8" 100 X 1/8FPT

SW ADAPTER

225-01-3220

HUMIDITY SYSTEM as viewed from the front.

Note: The axial fans included in the humidity system must be

replaced as a unit.

Refrigeration

REFRIGERANT TYPE

The standard refrigerant will be R-22 unless otherwise

specified on the customer order. Check the serial plate

on the case for information.

PIPING

The refrigerant line outlets are located under the case.

Locate first the electrical box, the outlets are then on the

same side of the case, but at the opposite end. Insulate

suction lines to prevent condensation drippage.

REFRIGERATION LINES

LIQUID SUCTION

1/2" O.D. 5/8" O.D.

NOTE: The standard coil is piped at 5/8" (suction); however,

the store tie-in may vary depending on the number of

coils and the draw the case has. Depending on the case

setup, the connecting point in the store may be

5/8", 7/8", or 11/8". Refer to the particular case you are

hooking up.

Refrigerant lines should be sized as shown on the

refrigeration legend furnished by the store.

Install P-traps (oil traps) at the base of all suction line vertical

risers.

Pressure drop can rob the system of capacity. To keep the

pressure drop to a minimum, keep refrigerant line run as

short as possible, using the minimum number of elbows.

Where elbows are required, use long radius elbows only.

CONTROL SETTINGS

See the “Case Specs” section of this guidebook for the

appropriate settings for your merchandiser. Maintain these

parameters to achieve near constant product

temperatures. Product temperature should first be

measured in the morning, after having been refrigerated

overnight. For all multiplexing, defrost should be time

terminated. Defrost length and frequency should as

directed in the Case Specifications section of this guide.

The number of defrosts per day should never change. The

duration of the defrost cycle may be adjusted to meet

conditions present at your location.

Rev.0303

ACCESS TO TX VALVES AND DRAIN LINES

MECHANICAL - Remove product from case. Remove pans.

TX valve (mechanical only) and drain are located under the

pans within the case.

ELECTRONIC - The electronic expansion valve master and

slave cylinder(s) are located within the electrical access

panel(s) in the rear of case. Rear panels lift up and out.

NOTE: Duplex receptacles must be detached before

removing rear panels.

ELECTRONIC EXPANSION VALVE (OPTIONAL)

A wide variety of electronic expansion valves and case

controllers can be utilized. Please refer to EEV and

controller Hussmann’s information sheet. Sensors for

electronic expansion valves will be installed on the coil

inlet, coil outlet, and in the discharge air. (Some

supermarkets require a 4th sensor in the return air). Case

controllers will be located in the electrical raceway or

under the case.

THREE THERMOSTATIC EXPANSION VALVES

ALCO balanced port expansion valves are furnished as

standard equipment, unless otherwise specified by

customer.

EXPANSION VALVE ADJUSTMENT

Expansion valves must be adjusted to fully feed the

evaporator. Before attempting any adjustments, make sure

the evaporator is either clear or very lightly covered with

frost, and that the fixture is within 10°F of its expected

operating temperature.

After case has been brought to

running temperature, tighten glass screws

along clamshell.

MEASURING THE OPERATING SUPERHEAT

1. Determine the suction pressure with an accurate

pressure gauge at the evaporator outlet.

2. From a refrigerant pressure temperature chart,

determine the saturation temperature at the

observed suction pressure.

3. Measure the temperature of the suction gas at the

thermostatic remote bulb location.

4. Subtract the saturation temperature obtained in step No.

2 from the temperature measured in step No. 3.

3. The difference is superheat.

5. Set the superheat for 5°F - 7°F.

T-STAT LOCATION

T- Stats are located in the electrical section; behind the rear

panel, on the right-hand side of the case (facing the back of

the case).

T-Stat

Electrical Raceway

IGSV-ASCS-0303

Electrical

WIRING COLOR CODE

GREEN GROUND

PURPLE ANTI-SWEAT

ORANGE LIGHTS

YELLOW RECEPTACLE

RED / BLACK T-STAT /SOLENOID230V

BLACK / WHITET-STAT / SOLENOID 115V

BROWN FAN MOTORS

CASE MUST BE GROUNDED

NOTE: Refer to label affixed to case to determine the actual

configuration as checked in the “TYPE INSTALLED” boxes.

ELECTRICAL CIRCUIT IDENTIFICATION

Standard lighting for all models will be full length fluorescent

lamps located within the case at the top.

The switch controlling the lights, the plug provided for digital

scale, and the thermometer are located at the rear of the case

mullion.

The receptacle that is provided on the exterior back of these

models is intended for computerized scales with a five amp

maximum load, not for large motors or other high wattage

appliances. It should be wired to a dedicated circuit.

CASE-TO CASE CONNECTORS

HUSSMANN/CHINO now provides “CASE-TO-CASE”

locking electrical connector fittings on the ASCS service cases.

These connectors greatly simplify field installation thereby saving

time and electrical installation costs.

NOTE: The total case electrical draw must not exceed

30 Amps ampacity at 115V in one connected lineup.

ELECTRICAL SERVICE RECEPTACLES

(WHEN APPLICABLE)

The receptacles located on the exterior of the

merchandiser are intended for scales and lighted displays.

They are not intended nor suitable for large motors or

other external appliances.

BEFORE SERVICING

Always Disconnect Electrical

Power at the Main Disconnect

when servicing or replacing any

electrical component.

This includes (but not limited to) Fans, Heaters,

Thermostats, and Lights.

FIELD WIRING AND SERIAL PLATE AMPERAGE

Field wiring must be sized for component amperes printed

on the serial plate. Actual ampere draw may be less than

specified. Field wiring from the refrigeration control panel

to the merchandisers is required for refrigeration

thermostats. Most component amperes are listed in the

“Case Specs” section, but always check the serial plate.

BALLAST LOCATION

Ballasts are located within the access panel that runs the

length of the rear of the case. Refer to diagram on page 6.

WIRING AND SERIAL PLATE AMPERAGE

Field wiring must be sized for component amperes stamped

on the serial plate. Actual ampere draw may be less than

specified. Field wiring from the refrigeration control panel to

the merchandisers is required for refrigeration thermostats.

Most component amperes are listed in the "Case Specs" section,

but always check the serial plate.

ASHRAE COLOR CODE

NOTE: All other manufacturers; no known sensor codes

Case Control Systems SENSOR COLORS

Manufacturer ® > EIL CPC

Location

Coil Inlet Color Blue Blue

Part# 225-01-1755 225-01-3255

Coil Outlet Color Red Red

Part# 225-01-1757 225-01-3123

Discharge Air Color Green Green

Part# 225-01-1756 225-01-3260

Return Air Color Purple Green

Part# 225-01-1758 225-01-3260

Defrost Term. Color White Orange

Part# 225-01-0650 225-01-3254

Liquid Line Color White Blue

Part# 225-01-0650 225-01-3255

Rev.0303

Finishing Touches

JOINT TRIM

After cases have been leveled and joined, and refrigeration,

electrical, and waste piping work completed, install the

splashguards. Fasten along the top edge, or center, with

#10 X 3/3" sheet metal screws.

Joint Trim

ASCS

Butyl Locations

DO NOT SEAL JOINT T RIM T O FLOOR!

BUMPER INSTALLATION TIPS

1. Start to attach the bumper at one end of the lineup,

preferably on a straight case.

2. Push the end of the bumper into the bumper channel

firmly. This may be difficult if bumper is cold.

3. Bend the bumper backwards to open and guide it

forward onto the bumper channel.

4. An inside bumper miter must be cut on wedges.

5. Loose ends on miters must be anchored with screws

on the bottom edge.

6. The top and bottom edges of the bumper must be

firmly seated into the retainer by applying with a

rubber mallet (not by hand).

7. The bumper should be struck by the mallet at a slight

angle that forces the bumper back into itself to

prevent stretching. The installation can be made easier

by applying a paraffin block to the retainer grooves.

INSTALLING SPLASHGUARD

After merchandisers have been leveled and joined, and all

drip piping, electrical and refrigeration work has been

completed, install the splashguards. Splashguards may be

sealed to the floor using a vinyl cove base trim. The size of

trim needed will depend on how much the floor is out of

level. NOTE: The splashguard must be removable to allow

access to components behind it.

1. Remove all dirt, wax, debris, etc. from the area of the

splashguard to ensure a secure adhesion.

2. Apply a good contact cement to the trim, allowing a

proper dry time.

3. Install trim to the splashguard so that it is flush with

the floor.

IGSV-ASCS-0303

User Information

STOCKING

Improper temperature and lighting will cause serious

product loss. Discoloration, dehydration and spoilage can

be controlled with proper use of the equipment and

handling of product. Product temperature should always

be maintained at a constant and proper temperature. This

means that from the time the product is received, through

storage, preparation and display, the temperature of the

product must be controlled to maximize life of the product.

Hussmann cases were not designed to “heat up” or “cool

down” product—but rather to maintain an item’s proper

temperature for maximum shelf life. To achieve the

protection required always:

1. Minimize processing time to avoid damaging

temperature rise to the product. Product should be at

proper temperature.

2. Keep the air in and around the case area free of foreign

gasses and fumes or food will rapidly deteriorate.

3. Maintain the display merchandisers temperature

controls as outlined in the refrigerator section of this

manual.

4. Do not place any product into these refrigerators until

all controls have been adjusted and they are operating

at the proper temperature. Allow merchandiser to

operate a minimum of six (6) hours before stocking

with any product.

5. When stocking, never allow the product to extend

beyond the recommended load limit. Air discharge

and return air flue must be unobstructed at all

times to provide proper refrigeration.

6. There are vents located at the base of the front of the

glass, just above the front rail. These vents supply a

continuous, gentle flow of air across the front glass

which inhibits condensation. Do not place any

signs or other restrictive objects on the front of

the refrigerator that will block these vents.

7. Keep the service doors closed (when applicable).

Refrigeration performance will be seriously affected

if left open for a prolonged period of time.

8. Avoid the use of supplemental flood or spot lighting.

Display light intensity has been designed for maximum

visibility and product life at the factory. The use of

higher output fluorescent lamps (H.O. and V.H.O.), will

shorten the shelf life of the product.

9. In the Deli, Meat and Fish cases, completely cover the

product each night with a clean damp cloth or butcher

paper (never use plastic, as it does not allow for

proper circulation). Make sure the cloth or paper is in

direct contact with the product.

10. Turn and rotate the meat fairly often. The blood which

gives the pink color works its way downward with

time.

11. Cold coils remove heat and moisture from the case

and deposit this as frost onto the coil. Thus, a defrost

is required. Our humidity system induces moisture

into the case and helps slow down the dehydration

process. The only other moisture within the case is

that in the product itself. A single level of meat will dry

out faster than a fully loaded case of 3–4 levels of meat.

IMPORTANT STEPS

1. Do not set temperature too cold, as this causes

product dehydration. Product Temperature: 33°–

35°! Set thermostat to cut in at 28° discharge air. Meat

holding box: 32°. Meat prep room: 55°. Meat bloom

box: 36°. Process the meat to enter case at 40° or

below. Product deterioration is very rapid above 40°.

2. Temperature control should be by means of a T-Stat

and Suction Stop Solenoid at each case. DO NOT use

EPR valves, Liquid line solenoids or electronic control

devices of any kind, as these allow temperature swings

causing dehydration and excessive energy

consumption.

3. Product should be worked and rotated on a regular

basis, not to exceed a 4 hour period.

4. At night, turn off case lights and cover the product

with a damp (not wet) cloth similar to cheese cloth

(etc.). This should be washed out in the morning and

kept in a walk-in box during the day—so that it is cool

and moist when covering the product.

5. Discharge air temperature should be approximately

26°F, with between 150-200 FPM air velocity. Do not

display product directly within the air discharge.

6. Clean humidity system a minimum of every 90 days for

proper system operation.

CASE CLEANING

Long life and satisfactory performance of any equipment

are dependent upon the care given to it. To insure long life,

proper sanitation and minimum maintenance costs, the

refrigerator should be thoroughly cleaned frequently. SHUT

OFF FAN DURING CLEANING PROCESS. It can be

unplugged within the case, or shut off entire case at the

source. The interior bottom may be cleaned with any

domestic soap or detergent based cleaners. Sanitizing

solutions will not harm the interior bottom, however, these

solutions should always be used according to the

Hussmann’s directions. It is essential to establish and

regulate cleaning procedures. This will minimize bacteria

causing discoloration which leads to degraded product

Rev.0303

appearance and significantly shortening product shelf life.

Soap and hot water are not enough to kill this bacteria. A

sanitizing solution must be included with each cleaning process

to eliminate this bacteria.

1. Scrub thoroughly, cleaning all surfaces, with soap and

hot water.

2. Rinse with hot water, but do not flood.

3. Apply the sanitizing solution according to Hussmann’s

directions.

4. Rinse thoroughly.

5. Dry completely before resuming operation.

CLEANING GLASS AND MIRRORS

Only use a soft cloth and mild glass cleaner for cleaning

any glass or mirrored components. Be sure to rinse and/

or dry completely.

Never use hot water on cold glass surfaces! It

may shatter and cause serious injury! Allow glass

surfaces to warm first.

CLEANING PRECAUTIONS

WHEN CLEANING:

TO PRESERVE THE ATTRACTIVE FINISH:

Do Use Water and a Mild Detergent for

the Exterior Only!

Do Not Use Abrasives or Steel Wool Scouring Pads

(these will mar the finish)

Do Not Use High Pressure Hoses

Do Not Introduce Water Faster than Waste

Outlet can Drain

Never Use a Cleaning or Sanitizing Solution

that has an OIL BASE (these will dissolve the

butyl sealants) or AMMONIA BASE

(this will corrode the copper components

of the case)

NON-GLARE GLASS

The high optical clarity of this glass is possible due to special

coatings on the glass surface itself. To preserve this coating

and the optical clarity, keep the glass clean.

Windex® or Glass Plus® are the only solutions

recommended for use in cleaning non-glare glass. The

damage to the glass from improper, caustic solutions is

irreparable.

In addition to cleaning the glass with the recommended

product, there are precautions that should be taken when

working and cleaning the inside of the case.

•When cleaning the inside of the cases, we recommend

that the glass be fully opened and covered to prevent

solutions from splashing onto the glass and ruining the

coating on the inside.

PLEXIGLASS and ACRYLIC CARE

Improper cleaning not only accelerates the cleaning cycle

but also degrades the quality of this surface. Normal daily

buffing motions can generated static cling attracting dust

to the surface. Incorrect cleaning agents or cleaning cloths

can cause micro scratching of the surface, causing the plastic

to haze over time.

CLEANING

Hussmann recommends using a clean damp chamois, or a

paper towel marked as “dust and abrasive free” with 210®

Plastic Cleaner and Polish available by calling Sumner

Labs at 1-800-542-8656. Hard, rough cloths or paper

towels will scratch the acrylic and should not be used.

ANTISTATIC COATINGS

The 210® has proven to be very effective in not only

cleaning and polishing the Plexiglass surface, but also

providing antistatic and anti-fog capabilities. This product

also seals pores and provides a protective coating.

IGSV-ASCS-0303

Maintenance

FOR PROMPT SERVICE

When Contacting the Factory

for support, Be sure to have the

Case MODEL and

SERIAL NUMBER Handy.

This Information is on a plate

located on the case itself.

BEFORE SERVICING

Always Disconnect Electrical

Power at the Main Disconnect

when servicing or replacing any

electrical component.

This includes (but not limited to) Fans, Heaters,

Thermostats, and Lights.

REPLACING FLUORESCENT LAMPS

Fluorescent lamps are furnished with a shatterproof

protective coating. The same type of lamp with protective

coating must be used if replaced.

ENCAPSULITE

SHATTERPROOF COATING - SA 10645

Complies with FDA USDA

& OSHA Regulations

for replacement call:

1-800-395-9229

Turn switch off then on after replacing bulb

NSF

EVAPORATOR FANS

The evaporator fans are located at the center front of

these merchandisers directly beneath the display pans.

Should fans or blades need servicing, always replace fan blades

with the raised embossed side of the blade TOWARD THE

MOTOR.

COPPER COILS

The copper coils used in Hussmann merchandisers may

be repaired in the field. Materials are available from local

refrigeration wholesalers.

Hussmann recommends using #15 Sil-Fos for repairs.

TIPS and TROUBLESHOOTING

Before calling for service, check the following:

1.Check electrical power supply to the equipment for

connection.

2.Check fixture loading. Overstocking case will affect

its proper operation.

3.If frost is collecting on fixture and/or product, check

that Humidity Control is working properly, and that no

outside doors or windows are open—allowing

moisture to enter store.

CLEANING PRECAUTIONS

WHEN CLEANING:

TO PRESERVE THE ATTRACTIVE FINISH:

Do Use Water and a Mild Detergent for

the Exterior Only!

Do Not Use Abrasives or Steel Wool Scouring Pads

(these will mar the finish)

Do Not Use High Pressure Hoses

Do Not Introduce Water Faster than Waste

Outlet can Drain

Never Use a Cleaning or Sanitizing Solution

that has an OIL BASE (these will dissolve the

butyl sealants) or AMMONIA BASE

(this will corrode the copper components

of the case)

Rev.0303

LIFT UP GLASS

IMPORTANT!

READ BEFORE RAISING FRONT GLASS :

HEX SCREWS ALONG CLAMSHELL MAY HAVE

LOOSENED DURING SHIPPING!! RETIGHTEN ALL

CLAMSHELL SCREWS BEFORE OPENING GLASS!

The top cylinders, which allow the raising and lowering of

the glass, have been carefully tested for proper tension.

However, during shipment, the lubricant inside may have

settled. This settling may cause excessive or uneven tension

on the glass - to the point of breakage.

After installing new cylinders, it is advisable to perform

these three easy steps before completely raising the front

glass.

1. Slowly raise and lower each glass section 6 times, to

a height of 6".

2. Increase the height to 12", and raise and lower the

glass 6 more times.

3. Finally, raise the glass to it's full extension. This should

release any settled lubricant in the cylinders, and

prevent any stress on the front glass. (1)(3)

RE-ADJUSTMENT After Initial STARTUP

In addition to verifying that the Allen screws on the lift-up

glass are tightened when the case is delivered, recheck

the Allen screws on the glass ONCE THE CASE IS

IN FULL OPERATION AND BROUGHT TO

TEMPERATURE.

Temperature changes can affect the size and shape of the

materials involved, and cas cause changes in the secure fit

of the glass and the clamp.

Important Glass Notifications

Cylinders are a wear item.

They are designed:

•To support the glass

when fully open

•to allow the glass to

close slowly

Have your Service

Contractor replace the

cylinders when required.

CAUTION

Glass is heavy and

can cause bodily

damage. Check

support cylinders

for periodic

maintenance

Once cylinders are

removed, front glass

will have NO support to

maintain a raised

position. Support the

front glass at all times

until cylinder is

replaced or the glass

is lowered.

Maintenance (continued)

IGSV-ASCS-0303

Maintenance (continued)

1. Remove 2. Lift open 3. Loosen hex screw 4. Add or remove 5. Close glass panel(s)

top glass glass panel(s) (1/4" allen). shims as needed. and check alignment

and panel and relieve Remove chrome (see note on shims Retighten hex screw

enclosing tension on access cap in order below) and reinstall removed

mini-top hinge. to hold nut plate. components.

hardware.

1. Remove 2. Lift open 3. Loosen (4mm) 4. Move panel

top glass glass panel(s) screw slightly. as required

enclosing and relieve one at each hinge Retighten components

mini-top tension on

hardware. hinge.

Back

of Case

Inside

of Case

Chrome cap

for access to

nut plate

nut

plate

CUT VIEW:

Mini Top

Hardware

Adjust glass Up and Down

(vertically)

Adjust glass Side to Side

(horizontally)

Adjust glass Front to Back

NOTE: Before making any of the recommended adjustments,

Verify that the case(s) have been leveled properly.

1. Remove 2. Estimate 3. Lift open 4. Loosen hex screw 5. Slide the mini-top

top glass amount of glass panel(s) (1/4" allen) slightly. forward or backward

and panel adjustment and relieve Remove chrome to the mark in step 2.

enclosing and make tension on access plate in order Check alignment of

mini-top pencil mark hinge. to hold nut plate. glass.

hardware. on the mini-cam. Retighten components.

NOTE: Standard shim thickness is 1/16"

RGSDS hardware shown

Tech/glassadj/970602 tn

Rev.0303

Electrical and Refrigeration Specifications

TEMPERATURE DISCHG. FAN SIZE DEFROST

115 V. ELECTRICAL CIRCUITS

SELF CONTA INED UNIT DATA / SEE CROSS

REF.

MODEL NUMBER

BTU AVG AIR T-STAT/ TYPE TYPE FREQ. AIR SWEEP SELF CONTAINED

REQ’D EVAP PROD DISC VELOC CUT IN OF & NUMBER & FANS/WARMER STD. WARMERS HUMIDITY LOW PRESSURE

CASE LENGTH

PER FT. TMP TMP TMP @FPM SETTINGS COIL USE OF MOTORS DURATION (OPTIONAL) FANS LIGHTS FANS CONTROL & SETTINGS H.P. VOLTS AMPACITY

ASCS

4' Deli 650 20° 36° 28° 250 28° Forced Airsweep - 4

" Axial 1 36 min. 0.18 0.36 .35 1.08 0.16 30# Out

115 10.9

Meat/Fish 33° 26° 26° 26° Air Evap fans - 8” x 15° 1 (4) 1.68 50# In

Humidity 3

" Axial 1

6' Deli 650 20° 36° 28° 250 28° Forced Airsweep - 4

" Axial 2 36 min. 0.36 0.72 .52 1.62 0.16 30# Out

115 19.9

Meat/Fish 33° 26° 26° 26° Air Evap fans - 8” x 15° 2 (4) 1.68 50# In

Humidity 3

" Axial 1

8' Deli 650 20° 36° 28° 250 28° Forced Airsweep - 4

" Axial 3 36 min. 0.54 0.72 .70 1.62 0.16 30# Out

208/ 8.7

Meat/Fish 33° 26° 26° 26° Air Evap fans - 8” x 15° 2 (4) 2.24 50# In 230

Humidity 3

" Axial 1

10' Deli 650 20° 36° 28° 250 28° Forced Airsweep - 4

" Axial 3 36 min. 0.54 1.08 .87 2.70 0.32 30# Out 1 208/ 13.0

Meat/Fish 33° 26° 26° 26° Air Evap fans - 8” x 15° 3 (4) 2.80 50# In 230

Humidity 3

" Axial 2

12' Deli 650 20° 36° 28° 250 28° Forced Airsweep - 4

" Axial 3 36 min. 0.54 1.08 1.04 2.70 0.32 30# Out 1 208/ 13.0

Meat/Fish 33° 26° 26° 26° Air Evap fans - 8” x 15° 3 (4) 3.36 50# In 230

Humidity 3

" Axial 2

NOTE: Case temperature is controlled by a factory installed thermostat and suction solenoid (excluding self contained cases), no other controls are recommended or suported.

The total case electrical draw must not exceed 30 Amps Ampacity @ 115 Volts in one connected lineup.

ASCS for Bakery

4' - - - - - - - 8” x 15° 1 - - .6 - 1.22

used for air circulation

6' - - - - - - - 8” x 15° 2 - - 1.2 - 1.83

used for air circulation

8' - - - - - - - 8” x 15° 2 - - 1.2 - 1.83

used for air circulation

10' - - - - - - - 8” x 15° 3 - - 1.8 - 3.05

used for air circulation

12' - - - - - - - 8” x 15° 3 - - 1.8 - 3.05

used for air circulation

ASCS Wedges

45° Inside Load on parent case

Outside Load on parent case

90° Inside - Deli 2670 20° 36° 28° 250 28° Forced Anti Sweat 4

" Axial 1 36 min. 0.18 0.6 - 0.61

Inside - Meat 34° 26° 26° 26° Air Evap fans - 8” x 15° 1 (4) 1.68

90° Outside - Deli 2670 20° 36° 28° 250 28° Forced Anti Sweat 4

" Axial 1 36 min.0.18 0.6 - 0.61

Outside - Meat 34° 26° 26° 26° Air Evap fans - 8” x 15° 1 (4) 1.68

HUSSMANN CHINO CASE SPECIFICATIONS 0201

INQUIRIES? Technical (800) 395-9229 X2133 Service (800) 395-2320 Parts and Warranty Information (800) 395-9229 X2131

Note: These merchandisers are designed for use in stores where temperature and humidity do not exceed 75°F and 55% R.H. (We reserve the right to change or revisespecifications and product design in

connection with any features of our products. Such changes do not entitle the buyer to corresponding changes, improvements, additions, or replacement of equipment previously sold or shipped).

IGSV-ASCS-0303

DATE:

PROJECT TITLE: DWG #:DRAWN BY:

PRODUCTION ORDER #: DRAWING TITLE:

DATE:

REVISIONS:

#: DESCRIPTION: CHECKED BY:BY:

FILE LOCATION:

ADRIAN E. CRISCI

AEC

PAGE OF

HUSSMANN CORPORATION

13770 RAMONA AVENUE

CHINO, CA.91710

(909) 590-4910 LIC.#: 644406

311

04/15/02

H:\WIRESCHEMATICS\NEW-WIRING

ASC / ASCS CASES W0100020

2' CASE WIRING DIAGRAM

OVERHEAD CANOPY LIGHTS

(2) F17T8-SPX30

LIGHT SWITCH

125-04-0111

125-04-0112

125-01-0110 SUCTION SOLENOID

HUMIDITY FAN

125-04-0110

BALLAST

LH3-120-L

(1)125-04-0142

THERMOSTAT

DUPLEX RECEPTACLES

NOT USED

GFCI DEDICATED

LINE

125-04-0113

NOT USED

125-04-0113

NOT USED

125-04-0100

SINGLE CASE PIGTAIL

125-04-0101

CASE TO CASE HARNESS

125-04-0126

125-04-0115

LEDGE LIGHT (OPTIONAL)

SEE DWG W0100016

125-04-0119

125-04-0116

HEATER WIRE

(CASE REAR)

CAP

125-04-0147

EVAPORATOR FAN

125-04-0122

(OPTIONAL)

125-04-0123

(OPTIONAL)

TUBULAR HEATER ELEMENT

FRONT AIR SWEEP HEATER

(OPTIONAL)

HEATER SWITCH

(OPTIONAL)

AIR SWEEP / ANTI-SWEAT FAN

125-04-0115

Electrical Schematics

Rev.0303

DATE:

PROJECT TITLE: DWG #:DRAWN BY:

PRODUCTION ORDER #: DRAWING TITLE:

DATE:

REVISIONS:

#: DESCRIPTION: CHECKED BY:BY:

FILE LOCATION:

ADRIAN E. CRISCI

AEC

PAGE OF

HUSSMANN CORPORATION

13770 RAMONA AVENUE

CHINO, CA.91710

(909) 590-4910 LIC.#: 644406

311

04/15/02

H:\WIRESCHEMATICS\NEW-WIRING

ASC / ASCS CASES W0100021

4' CASE WIRING DIAGRAM

OVERHEAD CANOPY LIGHTS

(2) F32T8-SPX30

LIGHT SWITCH

125-04-0111

125-04-0112

125-01-0110 SUCTION SOLENOID

HUMIDITY FAN

125-04-0110

BALLAST

LH3-120-L

(2)125-04-0142

THERMOSTAT

DUPLEX RECEPTACLES

NOT USED

GFCI DEDICATED

LINE

125-04-0113

NOT USED

125-04-0113

NOT USED

125-04-0100

SINGLE CASE PIGTAIL

125-04-0101

CASE TO CASE HARNESS

125-04-0103

125-04-0115

LEDGE LIGHT (OPTIONAL)

SEE DWG W0100016

125-04-0119

125-04-0116

HEATER WIRE

(CASE REAR)

CAP

125-04-0147

EVAPORATOR FAN

125-04-0122

(OPTIONAL)

125-04-0123

(OPTIONAL)

TUBULAR HEATER ELEMENT

FRONT AIR SWEEP HEATER

(OPTIONAL)

HEATER SWITCH

(OPTIONAL)

AIR SWEEP / ANTI-SWEAT FAN

125-04-0115

125-04-0112

FRONT LIGHT

(1) F32T8-SPX30

Electrical Schematics Continued

IGSV-ASCS-0303

DATE:

PROJECT TITLE: DWG #:DRAWN BY:

PRODUCTION ORDER #: DRAWING TITLE:

DATE:

REVISIONS:

#: DESCRIPTION: CHECKED BY:BY:

FILE LOCATION:

ADRIAN E. CRISCI

AEC

PAGE OF

HUSSMANN CORPORATION

13770 RAMONA AVENUE

CHINO, CA.91710

(909) 590-4910 LIC.#: 644406

311

04/15/02

H:\WIRESCHEMATICS\NEW-WIRING

ASC / ASCS CASES W0100022

6' CASE WIRING DIAGRAM

125-04-0119

HEATER WIRE

(CASE REAR)

125-04-0147

125-04-0122

(OPTIONAL)

125-04-0123

(OPTIONAL)

TUBULAR HEATER ELEMENT

FRONT AIR SWEEP HEATER

(OPTIONAL)

HEATER SWITCH

(OPTIONAL)

125-04-0115

AIR SWEEP / ANTI-SWEAT FANS

125-04-0121

LEDGE LIGHT (OPTIONAL)

SEE DWG W0100016

EVAPORATOR

FAN

PLENUM EXTENSION

125-04-0148

EVAPORATOR

FAN

CAP

BALLASTS

LH3-120-L

(3) 125-04-0142

125-04-0110

HUMIDITY FAN

SUCTION SOLENOID

OVERHEAD CANOPY LIGHTS

(4) F257T8-SPX30

LIGHT SWITCH

125-04-0112

THERMOSTAT

DUPLEX RECEPTACLES

GFCI DEDICATED

LINE

125-04-0113

125-04-0100

SINGLE CASE PIGTAIL

125-04-0101

CASE TO CASE HARNESS

125-04-0104

BALLAST EXTENSION BOX

(SWITCHED POWER)

125-04-0113

125-04-0111

125-04-0112

CASE FRONT LIGHTS

(2) F25T8-SPX30

Electrical Schematics Continued

Rev.0303

DATE:

PROJECT TITLE: DWG #:DRAWN BY:

PRODUCTION ORDER #: DRAWING TITLE:

DATE:

REVISIONS:

#: DESCRIPTION: CHECKED BY:BY:

FILE LOCATION:

ADRIAN E. CRISCI

AEC

PAGE OF

HUSSMANN CORPORATION

13770 RAMONA AVENUE

CHINO, CA.91710

(909) 590-4910 LIC.#: 644406

311

04/15/02

H:\WIRESCHEMATICS\NEW-WIRING

ASC / ASCS CASE W0100023

8' CASE WIRING DIAGRAM

125-04-0119

HEATER WIRE

(CASE REAR)

125-04-0147

125-04-0122

(OPTIONAL)

125-04-0123

(OPTIONAL)

TUBULAR HEATER ELEMENT

FRONT AIR SWEEP HEATER

(OPTIONAL)

HEATER SWITCH

(OPTIONAL)

125-04-0115

AIR SWEEP / ANTI-SWEAT FANS

125-04-0121

LEDGE LIGHT (OPTIONAL)

SEE DWG W0100016

EVAPORATOR

FAN

PLENUM EXTENSION

125-04-0148

EVAPORATOR

FAN

CAP

BALLASTS

LH3-120-L

(3) 125-04-0142

125-04-0110

HUMIDITY FAN

SUCTION SOLENOID

OVERHEAD CANOPY LIGHTS

(4) F327T8-SPX30

LIGHT SWITCH

125-04-0112

THERMOSTAT

DUPLEX RECEPTACLES

GFCI DEDICATED

LINE

125-04-0113

125-04-0100

SINGLE CASE PIGTAIL

125-04-0101

CASE TO CASE HARNESS

125-04-0105

BALLAST EXTENSION BOX

(SWITCHED POWER)

125-04-0113

125-04-0111

125-04-0112

CASE FRONT LIGHTS

(2) F32T8-SPX30

Electrical Schematics Continued

IGSV-ASCS-0303

DATE:

PROJECT TITLE: DWG #:DRAWN BY:

PRODUCTION ORDER #: DRAWING TITLE:

DATE:

REVISIONS:

#: DESCRIPTION: CHECKED BY:BY:

FILE LOCATION:

ADRIAN E. CRISCI

AEC

PAGE OF

HUSSMANN CORPORATION

13770 RAMONA AVENUE

CHINO, CA.91710

(909) 590-4910 LIC.#: 644406

311

04/15/02

H:\WIRESCHEMATICS\NEW-WIRING

ASC / ASCS CASES W0100024

10' CASE WIRING DIAGRAM

125-04-0119

HEATER WIRE

(CASE REAR)

125-04-0147

125-04-0122

(OPTIONAL)

125-04-0123

(OPTIONAL)

TUBULAR HEATER ELEMENT

FRONT AIR SWEEP HEATER

(OPTIONAL)

HEATER SWITCH

(OPTIONAL)

125-04-0115

AIR SWEEP / ANTI-SWEAT FANS

125-04-0121

LEDGE LIGHT (OPTIONAL)

SEE DWG W0100016

EVAPORATOR

FAN

PLENUM EXTENSION

125-04-0148

EVAPORATOR

FAN

PLENUM EXTENSION

125-04-0148

EVAPORATOR

FAN

CAP

BALLASTS

LH3-120-L

(5) 125-04-0142

125-04-0110

HUMIDITY FANS

SUCTION SOLENOID

OVERHEAD CANOPY LIGHTS

(4) F257T8-SPX30 + (2) F32T8-SPX30

LIGHT SWITCH

125-04-0112

THERMOSTAT

DUPLEX RECEPTACLES

GFCI DEDICATED

LINE

125-04-0113

125-04-0100

SINGLE CASE PIGTAIL

125-04-0101

CASE TO CASE HARNESS

125-04-0106

BALLAST EXTENSION BOX

(SWITCHED POWER)

125-04-0113

125-04-0114

125-04-0111

125-04-0112

CASE FRONT LIGHTS

(2) F25T8-SPX30 + (1) F32T8-SPX30

Electrical Schematics Continued

Rev.0303

DATE:

PROJECT TITLE: DWG #:DRAWN BY:

PRODUCTION ORDER #: DRAWING TITLE:

DATE:

REVISIONS:

#: DESCRIPTION: CHECKED BY:BY:

FILE LOCATION:

ADRIAN E. CRISCI

AEC

PAGE OF

HUSSMANN CORPORATION

13770 RAMONA AVENUE

CHINO, CA.91710

(909) 590-4910 LIC.#: 644406

311

04/15/02

H:\WIRESCHEMATICS\NEW-WIRING

ASC / ASCS CASES W0100025

12' CASE WIRING DIAGRAM

125-04-0119

HEATER WIRE

(CASE REAR)

125-04-0147

125-04-0122

(OPTIONAL)

125-04-0123

(OPTIONAL)

TUBULAR HEATER ELEMENT

FRONT AIR SWEEP HEATER

(OPTIONAL)

HEATER SWITCH

(OPTIONAL)

125-04-0115

AIR SWEEP / ANTI-SWEAT FANS

125-04-0121

LEDGE LIGHT (OPTIONAL)

SEE DWG W0100016

EVAPORATOR

FAN

PLENUM EXTENSION

125-04-0148

EVAPORATOR

FAN

PLENUM EXTENSION

125-04-0148

EVAPORATOR

FAN

CAP

BALLASTS

LH3-120-L

(5) 125-04-0142

125-04-0110

HUMIDITY FANS

SUCTION SOLENOID

OVERHEAD CANOPY LIGHTS

(6) F327T8-SPX30

LIGHT SWITCH

125-04-0112

THERMOSTAT

DUPLEX RECEPTACLES

GFCI DEDICATED

LINE

125-04-0113

125-04-0100

SINGLE CASE PIGTAIL

125-04-0101

CASE TO CASE HARNESS

125-04-0107

BALLAST EXTENSION BOX

(SWITCHED POWER)

125-04-0113

125-04-0114

125-04-0111

125-04-0112

CASE FRONT LIGHTS

(3) F32T8-SPX30

Electrical Schematics Continued

IGSV-ASCS-0303

DATE:

PROJECT TITLE: DWG #:DRAWN BY:

PRODUCTION ORDER #: DRAWING TITLE:

DATE:

REVISIONS:

#: DESCRIPTION: CHECKED BY:BY:

FILE LOCATION:

ADRIAN E. CRISCI

AEC

PAGE OF

HUSSMANN CORPORATION

13770 RAMONA AVENUE

CHINO, CA.91710

(909) 590-4910 LIC.#: 644406

311

04/15/02

H:\WIRESCHEMATICS\NEW-WIRING

ASC-UPP ADD ONS W0100013

ASC-UPP SETUP FOR MITERED WEDGES

REDRAWN TO SPEC FROM 0916/99 BY AEC 04/15/02 AEC

INSTALL ¼" SPADE CONNECTORS

ON FAN LEADS FOR FIELD

REPLACEMENT

WRAP WITH INSULATION

TAPE FOR MOISTURE

CONTROL

CASE FRONT

MITER MITER

PLENUM PLENUM

FAN

UPP PANEL

MITER WEDGE FAN

(3" AXIAL FAN)

WEDGE FAN HARNESS

125-04-0124

EVAPORATOR

FAN

PLENUM EXTENSION

125-04-0148

(IF REQUIRED)

EVAPORATOR

FAN

PRIMARY FAN HARNESS

125-04-0147

CABLE SPLITTER

125-04-0119

USE AIR-SWEEP HARNESS TO

EXTEND WIRING

125-04-0122

STANDARD ASC-UPP POWER

PANEL 125-04-0100

INSTALL ¼" SPADE CONNECTORS

ON FAN LEADS FOR FIELD

REPLACEMENT

MITER WEDGE FAN

(3" AXIAL FAN)

WRAP WITH INSULATION

TAPE FOR MOISTURE

CONTROL

NOTE:

CASE COMPONENT LAYOUT DEPENDS ON PARENT CASE DESIGN. (BALLOON

NUMBERS INDICATE CORRESPONDING MATCHING HARNESS)

¤ ALL COMPONENTS ARE ADDITIONAL TO EXISTING CASE HARNESSES ¤

FOR "RIGHT" MITER CASE USE ONLY:

(1) 125-04-0119 + (1) 125-04-0122

FOR "LEFT" MITER CASE USE ONLY:

(1) 125-04-0124

FOR "DOUBLE MITERED" CASES USE:

(1) 125-04-0119 + (1) 125-04-0122 + (1) 125-04-0124

Electrical Schematics Continued

Rev.0303

DATE:

PROJECT TITLE: DWG #:DRAWN BY:

PRODUCTION ORDER #: DRAWING TITLE:

DATE:

REVISIONS:

#: DESCRIPTION: CHECKED BY:BY:

FILE LOCATION:

ADRIAN E. CRISCI

AEC

PAGE OF

HUSSMANN CORPORATION

13770 RAMONA AVENUE

CHINO, CA.91710

(909) 590-4910 LIC.#: 644406

311

04/15/02

H:\WIRESCHEMATICS\NEW-WIRING

WATER FLUSH W0100014

TYPICAL CASE WATER FLUSH SYSTEM

REDRAWN TO SPEC FROM 10/21/99 BY AEC 04/15/02 AEC

12:00

GRÄSSLIN

TIME CLOCK

125-04-0100

125-04-0119

PRIMARY FAN HARNESS

EVAPORATOR FAN

125-04-0127A

SOLENOID VALVE

ALCO 222CD½B½B-AMS

225-01-1340

INDICATOR LIGHT

(GREEN COLOR)

175-01-1122

PART # 125-01-0713

GRÄSSLIN FM/1 DIGI 20 - 120

NOTE: THE WATER FLUSH SYSTEM IS CONNECTED TO THE ASC-UPP

MAIN POWER PANEL THROUGH THE EVAPORATOR SYSTEM.

(USE CABLE SPLITTER 125-04-0119 TO CONNECT)

Electrical Schematics Continued

IGSV-ASCS-0303

DATE:

PROJECT TITLE: DWG #:DRAWN BY:

PRODUCTION ORDER #: DRAWING TITLE:

DATE:

REVISIONS:

#: DESCRIPTION: CHECKED BY:BY:

FILE LOCATION:

ADRIAN E. CRISCI

AEC

PAGE OF

HUSSMANN CORPORATION

13770 RAMONA AVENUE

CHINO, CA.91710

(909) 590-4910 LIC.#: 644406

312

04/15/02

H:\WIRESCHEMATICS\NEW-WIRING

LEDGE / NOSE LIGHTS W0100016

TYPICAL LEDGE LIGHT ASSEMBLIES

REDRAWN TO SPEC FROM 07/07/01 BY AEC 04/15/02 AEC

ADDED NOSE LIGHTS ON PAGE 2 OF 2 04/18/02 AEC

FP28T5 / 830 FP28T5 / 830 FP28T5 / 830

FP28T5 / 830 FP28T5 / 830

FP28T5 / 830

FP2IT5 / 830 FP2IT5 / 830

CAP UNUSED RED LEAD

4' CASES

6' CASES

8' CASES

10' CASES

12' CASES

RED

YELLOW

RED

YELLOW

RED

125-04-0119

BALLAST FULHAM

LH4-120-L 125-04-0141

BALLAST FULHAM

LH4-120-L 125-04-0141

BALLAST FULHAM

LH4-120-L 125-04-0141

BALLAST FULHAM

LH4-120-L 125-04-0141

BALLAST FULHAM

LH4-120-L 125-04-0141

CAP UNUSED RED LEAD

YELLOW

RED

RED YELLOW

RED

125-04-0119

BALLAST FULHAM

LH4-120-L 125-04-0141

BALLAST FULHAM

LH4-120-L 125-04-0141

FP21T5 / 830 FP28T5 / 830 FP21T5 / 830

YELLOW

RED

RED YELLOW

RED

FP14T5 / 830

CAP UNUSED RED LEAD

2' CASES

RED

YELLOW

BALLAST FULHAM

LH4-120-L 125-04-0141

Electrical Schematics Continued

Rev.0303

Electrical Schematics Continued

DATE:

PROJECT TITLE: DWG #:DRAWN BY:

PRODUCTION ORDER #: DRAWING TITLE:

DATE:

REVISIONS:

#: DESCRIPTION: CHECKED BY:BY:

FILE LOCATION:

ADRIAN E. CRISCI

AEC

PAGE OF

HUSSMANN CORPORATION

13770 RAMONA AVENUE

CHINO, CA.91710

(909) 590-4910 LIC.#: 644406

311

04/15/02

H:\WIRESCHEMATICS\NEW-WIRING

CASE POWER PANEL W0000001

ASC-UPP (UNIVERSAL POWER PANEL)

REDRAWN FROM 07/24/00 BY AEC 04/15/02 AEC

MAIN CONNECTOR BUNDLE COLOR & USE

LINE # COLOR USE

1 2 3 WHITE DEDICATED GFCI

4 5 6 YELLOW RECEPTACLES

7 10 ORANGE LIGHTS

8 11 PURPLE ANTI-SWEAT HTR + FAN

9 12 BROWN EVAP FANS + T-STAT

3 2 1

B B G

B W B WB WB WB W

B W B WB WB WB WB W

2 1

2 1 2 12 12 1

2 1 2 12 12 12 1

LIGHT SWITCH

BALLAST POWER CONNECTORS

LEDGE

LIGHTS

(SWITCHED)

AIR-SWEEP

FANS

ANTI-SWEAT

HEATER

HUMIDITY

FANS

EVAP.

FANS

SUCTION

SOLENOID

MAIN POWER PANEL

CONNECTOR

(18"LONG)

T-STAT

CONNECTIONS

RECEPTACLES

GFCI DEDICATED

OUTLETS

BALLASTS

EXTENSION BOX

CASE GROUND

REFERENCE WIRE COLOR:

B = BLACK

W = WHITE

G = GREEN

2 1

POWER PANEL INTERNAL WIRING

IGSV-ASCS-0303

Electrical Schematics Continued

DATE:

PROJECT TITLE: DWG #:DRAWN BY:

PRODUCTION ORDER #: DRAWING TITLE:

DATE:

REVISIONS:

#: DESCRIPTION: CHECKED BY:BY:

FILE LOCATION:

ADRIAN E. CRISCI

AEC

PAGE OF

HUSSMANN CORPORATION

13770 RAMONA AVENUE

CHINO, CA.91710

(909) 590-4910 LIC.#: 644406

311

04/15/02

H:\WIRESCHEMATICS\NEW-WIRING

CASE POWER PANEL W0000001

ASC-UPP (UNIVERSAL POWER PANEL)

REDRAWN FROM 07/24/00 BY AEC 04/15/02 AEC

MAIN CONNECTOR BUNDLE COLOR & USE

LINE # COLOR USE

1 2 3 WHITE DEDICATED GFCI

4 5 6 YELLOW RECEPTACLES

7 10 ORANGE LIGHTS

8 11 PURPLE ANTI-SWEAT HTR + FAN

9 12 BROWN EVAP FANS + T-STAT

3 2 1

B B G

B W B WB WB WB W

B W B WB WB WB WB W

2 1

2 1 2 12 12 1

2 1 2 12 12 12 1

LIGHT SWITCH

BALLAST POWER CONNECTORS

LEDGE

LIGHTS

(SWITCHED)

AIR-SWEEP

FANS

ANTI-SWEAT

HEATER

HUMIDITY

FANS

EVAP.

FANS

SUCTION

SOLENOID

MAIN POWER PANEL

CONNECTOR

(18"LONG)

T-STAT

CONNECTIONS

RECEPTACLES

GFCI DEDICATED

OUTLETS

BALLASTS

EXTENSION BOX

CASE GROUND

REFERENCE WIRE COLOR:

B = BLACK

W = WHITE

G = GREEN

2 1

POWER PANEL INTERNAL WIRING

Rev.0303

Light Switch

Overhead Canopy Lights Front Lights

Ledge Lights

(Optional)

Ballasts

WH3-120-164

(125-04-0118)

Thermostat Suction Solenoid

Duplex Receptacles

Humidity Fan

GFCI Dedicated

Line

Ballast Extension Box

(Switched Power)

Evaporator Fans

Cap

Case to Case Harness

Single case Pigtail

F25T8-SPX30 (2) F25T8-SPX30 (2) F25T8-SPX30 (2)

Plenum extension

Evaporator Fans

125-04-0104

125-04-0101

125-04-0108

125-04-0110

125-04-0111

125-04-0113

12GA Copper Jumper

125-04-0112

125-04-0113

125-04-0112

125-04-0110

125-04-0100

(Not used)

125-04-0117

125-04-0115

Anti-sweat Fans

(Optional)

125-04-0115

125-04-0119

Heater Wire

(case rear)

Tubular Heater Element

(Front air sweep heater)

(Optional)

125-04-0122

125-04-0123

Heater switch

(optional)

475-01-1421

(2) Anti-sweat Heater Rop 6' approx

Single Loop on Front extrusion

125-04-0109

Sheet ____ of ____

Date:

Project Title: Drawing No.:

Drawn By:

Next Assembly: Drawing Title:

Date:

Hussmann Corporation

13770 Ramona Avenue

Chino, CA. 91710

(909)-590-4910

Lic.#: 644406

Revisions:

No. Description: Checked By:

By:

6' Case layout with T8 Lights W0100002

ASC-UPP Universal Power Module

Adrian Crisci

05.02.2000

1 Added air sweep heater and harnesses 07/26/99 AEC

2 Updated front anti-sweat heater rope wire Installation 05.30.00 BK

IGSV-ASCS-0303

Light Switch

Overhead Canopy Lights Front Lights

Ledge Lights

(Optional)

Ballasts

WH3-120-164

(125-04-0118)

Thermostat Suction Solenoid

Duplex Receptacles

Humidity Fan

GFCI Dedicated

Line

Ballast Extension Box

(Switched Power)

Evaporator Fans

Cap

Case to Case Harness

Single case Pigtail

F32T8-SPX30 (2) F32T8-SPX30 (2) F32T8-SPX30 (2)

Plenum extension

Evaporator Fans

125-04-0105

125-04-0101

125-04-0120

125-04-0108

125-04-0110

125-04-0111

125-04-0113

125-04-0109

125-04-0112

125-04-0113

125-04-0112

125-04-0110

125-04-0100

(Not used)

125-04-0115

Anti-sweat Fans

(Optional)

125-04-0115

125-04-0119

Heater Wire

(case rear)

Tubular Heater Element

(Front air sweep heater)

(Optional)

475-01-1421

(2) Anti-sweat Heater Rope 8' approx

Single Loop on Front extrusion

125-04-0122

125-04-0123

Heater switch

(optional)

12GA Copper Jumper

Sheet ____ of ____

Date:

Project Title: Drawing No.:

Drawn By:

Next Assembly: Drawing Title:

Date:

Hussmann Corporation

13770 Ramona Avenue

Chino, CA. 91710

(909)-590-4910

Lic.#: 644406

Revisions:

No. Description: Checked By:

By:

8' Case layout with T8 Lights W0100003.dft

ASC-UPP Universal Power Module

Adrian Crisci

05.02.2000

1 Added air sweep heater and harnesses 07/26/99 AEC

2 Updated front anti-sweat heater rope wire installation 05.30.00 BK

Rev.0303

Light Switch

Overhead Canopy Lights Front Lights

Ledge Lights

Ballasts

WH3-120-164 (125-04-0118)

Thermostat

Suction Solenoid

Anti-sweat Fans

(Optional)

F32T8-SPX30 (1)

Duplex Receptacles

Humidity Fans

GFCI Dedicated

Line

Ballast Extension Box

(Switched Power)

Evaporator Fans

Cap

Case to Case Harness

Single case Pigtail

F25T8-SPX30 (2) F32T8-SPX30 (2) F25T8-SPX30 (2) F25T8-SPX30 (2)

Plenum extension

Evaporator Fans

Plenum extension

Evaporator Fans

125-04-0106

125-04-0101

125-04-0108

125-04-0109

125-04-0110

125-04-0112

125-04-0111

125-04-0114

125-04-0113

125-04-0109

125-04-0112

125-04-0113

125-04-0112

125-04-0110

125-04-0100

125-04-0121

125-04-0115

125-04-0119

Heater Wire

(case rear)

Tubular Heater Element

(Front air sweep heater)

(Optional)

475-01-14212

(2) Anti-sweat Heater Rope approx 10'

Single Loop on Front extrusion

-Standard-

125-04-0122

125-04-0123

Heater switch

(optional)

12GA Copper Jumper

Sheet of

final

Date:

Project Title: Drawing No.:

Drawn By:

Next Assembly: Drawing Title:

Date:

Hussmann Corporation

13770 Ramona Avenue

Chino, CA. 91710

(909)-590-4910

Lic.#: 644406

Revisions:

No. Description: Checked By:

By:

10' Case with T8 Lights W0100004.dft

ASC-UPP Universal Power Module

Adrian Crisci

05.02.2000

1 Added air sweep heater switch and harnesses 07/26/99 AEC

2 Updated front anti-sweat heater rope wire installation 05.24.00 BK

IGSV-ASCS-0303

Light Switch

Overhead Canopy Lights Front Lights

Ledge Lights

(Optional)

Ballasts

WH3-120-164 (125-04-0118)

Thermostat

Suction Solenoid

F32T8-SPX30 (1)

Duplex Receptacles

Humidity Fans

GFCI Dedicated

Line

Ballast Extension Box

(Switched Power)

Evaporator Fans

Cap

Case to Case Harness

Single case Pigtail

F32T8-SPX30 (2) F32T8-SPX30 (2) F32T8-SPX30 (2) F32T8-SPX30 (2)

Plenum extension

Evaporator Fans

Plenum extension

Evaporator Fans

125-04-0107

125-04-0101

125-04-0108

125-04-0109

125-04-0110

125-04-0112

125-04-0111

125-04-0114

125-04-0113

125-04-0112

125-04-0113

125-04-0112

125-04-0110

125-04-0100

125-04-0115

Heater Wire

(case rear)

Anti-sweat Fans

(Optional)

125-04-0121

125-04-0115

Tubular Heater Element

(Front air sweep heater)

(Optional)

125-04-0115

475-01-1421

(2) Anti-sweat Heat Rope 12' approx

Parallel Run on Front extrusion

125-04-0119

125-04-0109

125-04-0122

125-04-0123

Heater switch

(optional)

Sheet of

final

Date:

Project Title: Drawing No.:

Drawn By:

Next Assembly: Drawing Title:

Date:

Hussmann Corporation

13770 Ramona Avenue

Chino, CA. 91710

(909)-590-4910

Lic.#: 644406

Revisions:

No. Description: Checked By:

By:

12' Case with T8 Lights W0100005.dft

ASC-UPP Universal Power Module

Adrian Crisci

05.02.2000

1 Added air sweep heater switch and harnesses 07/23/99 AEC

2 Updated front anti-sweat heater rope wire 05.24.00 BK

Rev.0303

APPENDIX A. – Temperature Guidelines

Refrigerated

The refrigerators should be operated according to Hussmann’s published

engineering specifications for entering air temperatures for specific

equipment applications. Table 1 shows the typical temperature of the air

entering the food zone one hour before the start of defrost and one hour

after defrost for various categories of refrigerators. Refer to Appendix C for

Field Evaluation Guidelines.

TABLE 1

TYPE OF TYPICAL ENTERING

REFRIGERATOR AIR TEMPERATURE

I. OPEN DISPLAY

A. Non frozen:

1) Meat 28°F

2) Dairy/Deli 32°F

3) Produce

a. Processed 36°F

b. Unprocessed 45°F

B. Frozen 0°F

C. Ice Cream -5°F

II. CLOSED DISPLAY

A. Non frozen:

1) Meat 34°F

2) Dairy/Deli 34°F

3) Produce

a. Processed 36°F

b. Unprocessed 45°F

B. Frozen 0°F

C. Ice Cream -5°F

Single Deck Multi Deck Service Case Reach-In

I. Open Display Styles II. Closed Display Styles

APPENDIX B. – Application Recommendations

Refrigerated

1.0 Temperature performance is critical for controlling bacteria growth.

Therefore, the following recommendations are included in the standard.

They are based on confirmed field experience over many years.

1.1 The installer is responsible for following the installation instructions and

recommendations provided by Hussmann for the installation of each

individual type refrigerator.

1.2 Refrigeration piping should be sized according to Hussmann’s

equipment recommendations and installed in accordance with normal

refrigeration practices. Refrigeration piping should be insulated

according to Hussmann’s recommendations.

1.3 A clogged waste outlet blocks refrigeration. The installer is responsible

for the proper installation of the system which dispenses condensate

waste through an air gap into the building indirect waste system.

1.4 The installer should perform a complete start-up evaluation prior to

the loading of food into the refrigerator, which includes such items

as:

a) Initial temperature performance, coils should be properly fed with a

refrigerant according to Hussmann’s recommendations.

b) Observation of outside influences such as drafts, radiant heating

from the ceiling and from lamps. Such influence should be properly

corrected or compensated for.

c) At the same time, checks should be made of the store dry-bulb

and wet-bulb temperatures to ASCSertain that they are within the

limits prescribed by Hussmann.

d) Complete start-up procedures should include checking through a

defrost to make certain of its adequate frequency and length

without substantially exceeding the actual needs. This should

include checking the electrical or refrigerant circuits to make sure

that defrosts are correctly programmed for all the refrigerators

connected to each refrigeration system.

e) Recording instruments should be used to check performance.

APPENDIX C. – Field Recommendations -

Refrigerated

Recommendations for field evaluating the performance of retail

food refrigerators and hot cases

1.0 The most consistent indicator of display refrigerator performance is

temperature of the air entering the product zone (Refrigerated see

Diagram 1, Appendix A). In practical use, the precise determination of

return air temperature is extremely difficult. Readings of return air

temperatures will be variable and results will be inconsistent. The

product temperature alone is not an indicator of refrigerator

performance.

NOTE: Public Health will use the temperature of the product in

determining if the refrigerator will be allowed to display potentially

hazardous food. For the purpose of this evaluation, product temperature

above the FDA Food Code 1993 temperature for potentially hazardous food

will be the first indication that an evaluation should be performed. It is

expected that all refrigerators will keep food at the FDA Food Code 1993

temperature for potentially hazardous food.

1.1 The following recommendations are made for the purpose of arriving

at easily taken and understood data which, coupled with other

observations, may be used to determined whether a display refrigera-

tor is working as intended:

a) INSTRUMENT – A stainless steel stem-type thermometer is

recommended and it should have a dial a minimum of 1 inch

internal diameter. A test thermometer scaled only in Celsius or

Appendices

IGSV-ASCS-0303

dually scaled in Celsius and Fahrenheit shall be accurate to 1°C

(1.8°F). Temperature measuring devices that are scaled only in

Fahrenheit shall be accurate to 2°F. The thermometer should be

checked for proper calibration. (It should read 32°F when the stem

is immersed in an ice water bath).

b) LOCATION – The probe or sensing element of the thermometer

should be located in the airstream where the air first enters the

display or storage area, and not more than 1 inch away from the

surface and in the center of the discharge opening.

c) READING – It should first be determined that the refrigerator is

refrigerating and has operated at least one hour since the end of

the last defrost period. The thermometer reading should be made

only after it has been allowed to stabilize, i.e., maintain a constant

reading.

d) OTHER OBSERVATIONS – Other observations should be made which

may indicate operating problems, such as unsatisfactory product,

feel/appearance.

e) CONCLUSIONS – In the absence of any apparent undesirable

conditions, the refrigerator should be judged to be operating

properly. If it is determined that such condition is undesirable, i.e.,

the product is above proper temperature, checks should be made

for the following:

1. Has the refrigerator been loaded with warm

product?

2. Is the product loaded beyond the “Safe Load Line”

markers?

3. Are the return air ducts blocked?

4. Are the entering air ducts blocked?

5. Is a dumped display causing turbulent air flow and

mixing with room air?

6. Are spotlights or other high intensity lighting

directed onto the product?

7. Are there unusual draft conditions (from heating /

air-conditioning ducts, open doors, etc.)?

8. Is there exposure to direct sunlight?

9. Are display signs blocking or diverting airflow?

10. Are the coils of the refrigerator iced up?

11. Is the store ambient over 75°F, 55% RH as set forth

in ASHRAE Standard 72 and ASHRAE Standard 117?

12. Are the shelf positions, number, and size other than

recommended by Hussmann?

13. Is there an improper application or control system?

14. Is the evaporator fan motor/blade inoperative?

15. Is the defrost time excessive?

16. Is the defrost termination, thermostat (if used) set

too high?

17. Are the refrigerant controls incorrectly adjusted?

18. Is the air entering the condenser above design

conditions? Are the condenser fins clear of dirt, dust,

etc.?

19. Is there a shortage of refrigerant?

20. Has the equipment been modified to use

replacements for CFC-12, CFC-502 or other

refrigerant? If so, have the modifications been made in

accordance with the recommendations of Hussmann

equipment? Is the refrigerator charged with the

proper refrigerant and lubricant? Does the system use

the recommended compressor?

APPENDIX D. – Recommendations to user -

Refrigerated

1.0 Hussmann should provide instructions and recommendations for proper

periodic cleaning. The user will be responsible for such cleaning, including

the cleaning of low temperature equipment within the compartment and

the cooling coil area(s). Cleaning practices, particularly with respect to

proper refrigerator unloading and warm-up, must be in accordance with

applicable recommendations.

1.1 Cleaning of non frozen food equipment should include a weekly cleaning

of the food compartment as a minimum to prevent bacteria growth from

accumulating. Actual use and products may dictate more frequent cleaning.

Circumstances of use and equipment design must also dictate the frequency

of cleaning the display areas. Weekly washing down of the storage

compartment is also recommended, especially for equipment subject to

drippage of milk or other liquids, or the collection of vegetable, meat,

crumbs, etc. or other debris or litter. Daily cleaning of the external areas

surrounding the storage or display compartments with detergent and water

will keep the equipment presentable and prevent grime buildup.

1.2 Load levels as defined by Hussmann must be observed.

1.3 The best preservation is achieved by following these rules:

a) Buy quality products.

b) Receive perishables from transit equipment at the ideal temperature

for the particular product.

c) Expedite perishables to the store’s storage equipment to avoid

unnecessary warm-up and prolonged temperature recovery. Food

store refrigerators are not food chillers nor can they reclaim quality

lost through previous mishandling.

d) Care must be taken when cross merchandising products to ensure

that potentially hazardous vegetable products are not placed in non

refrigerated areas.

e) Display and storage equipment doors should be kept closed during

periods of inactivity.

f) Minimize the transfer time of perishables from storage to display.

g) Keep meat under refrigeration in meat cutting and processing area

except for the few moments it is being handled in processing. When

a cut or tray of meat is not to be worked on immediately, the

procedure should call for returning it to refrigeration.

h) Keep tools clean and sanitized. Since mechanical equipment is used

for fresh meat processing, all such equipment should be cleaned at

Rev.0303

least daily and each time a different kind of meat product comes

in contact with the tool or equipment.

i) Make sure that all refrigeration equipment is installed and adjusted

in strict accordance with Hussmann’s recommendations.

j) See that all storage and refrigeration equipment is kept in proper

working order by routine maintenance.

IGSV-ASCS-0303

Rev.0303

Limited Warranty

This warranty is made to the original user at the original installation site and is not transferable.

Hussmann merchandisers are warranted to be free from defect in material and workmanship under normal use and

service for a period of one (1) year from the date of original installation (not to exceed fifteen (15) months from the date of

shipment for the factory). Hussmann Impact Modular Coils are warranted for a total of five (5) years based upon

the above criteria. Hussmann’s obligation under this warranty shall be limited to repairing or exchanging any part or parts,

without charge F.O.B. factory or nearest authorized parts depot within said period and which is proven to the satisfaction of

the original manufacturing plant warranty group to be thus defective.

Hussmann covers the entire case or refrigeration product and all its components (except for lamps, driers, fuses, and

other maintenance type replacement parts) for the one (1) year warranty period.

Additionally, Hussmann warrants for a total period of three (3) years all sealed, multi-glass assemblies except those

used in sliding doors on closed meat display cases. If within three (3) years from the date of installation (not to exceed thirty-

nine (39) months from the date of shipment from factory), it shall be proven to the satisfaction of the originating factory

warranty group that there is impaired visibility through the multi-glass assemblies thereof caused by moisture between the

glasses, the multi-glass assembly will be replaced free of charge, F.O.B. factory. This additional warranty excludes accident,

misuse, or glass breakage.

On Hussmann manufactured self-contained display cases, Hussmann agrees to repair or exchange, at its option, the

original motor/compressor unit only with a motor/compressor of like or of similar design and capacity if it is shown to the

satisfaction of Hussmann that the motor/compressor is inoperative due to defects in factory workmanship or material under

normal use and service as outlined in Hussmann’s “Installation Instructions” which are shipped inside new Hussmann equipment.

Hussmann’s sole obligation under this warranty shall be limited to a period not to exceed five years from date of factory

shipment.

On Hussmann refrigeration systems, an additional (4) year extended warranty for the motor/compressor assembly

is available, but must be purchased prior to shipment to be in effect. Hussmann reserves the right to inspect the job site,

installation and reason for failure.

The motor/compressor warranties listed above do not include replacement or repair of controls, relays, capacitors,

overload protectors, valve plates, oil pumps, gaskets or any external part on the motor/compressor replaceable in the field, or

any other part of the refrigeration system or self-contained display case.

THE WARRANTIES TO REPAIR OR REPLACE ABOVE RECITED ARE THE ONLY WARRANTIES, EXPRESS, IMPLIED

OR STATUTORY, MADE BY HUSSMANN WITH RESPECT TO THE ABOVE MENTIONED EQUIPMENT, INCLUDING ANY

IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS, AND HUSSMANN NEITHER ASSUMES NOR AUTHORIZES

ANY PERSON TO ASSUME FOR IT, ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH THE SALE OF

SAID EQUIPMENT OR ANY PART THEREOF.

THIS WARRANTY SHALL NOT APPLY TO LOSS OF FOOD OR CONTENTS OF THE EQUIPMENT DUE

TO FAILURE FOR ANY REASON. HUSSMANN SHALL NOT BE LIABLE:

•For payment of labor for any removal or installation of warranted parts;

•For any repair or replacements made without the written consent of Hussmann, or when the equipment is installed or

operated in a manner contrary to the printed instructions covering installation and service which accompanied such

equipment;

•For any damages, delays, or losses, direct or consequential which may arise in connection with such equipment or part

thereof;

•For damages caused by fire, flood, strikes, acts of God or circumstances beyond its control;

•When the equipment is subject to negligence, abuse, misuse or when the serial number of the equipment has been removed,

defaced, or altered;

•When the equipment is operated on low or improper voltages

•When the equipment is put to a use other than normally recommended by Hussmann (i.e. deli case used for fresh meat);

•When operation of this equipment is impaired due to improper drain installation;

•For payment of refrigerant loss for any reason;

•For costs related to shipping or handling of replacement parts.

Hussmann Corporation, Corporate Headquarters: Bridgeton, Missouri, U.S.A. 63044 August 1, 1998

IGSV-ASCS-0303

The MODEL NAME and SERIAL NUMBER is required in order to provide you

with the correct parts and information for your particular unit.

They can be found on a small metal plate on the unit.

Please note them below for future reference.

MODEL:

SERIAL NUMBER:

/Chino

Additional copies of this publication may be obtained by contacting:

Hussmann® Chino

13770 Ramona Avenue • Chino, California 91710

(909) 628-8942 FAX

(909) 590-4910

(800) 395-9229

Service Record

Last service date: By:

Hussman Igsv Ascs 0303 Users Manual 6.5

IGSV-ASCS-0303 to the manual ba921330-dada-4896-abd4-d1e31fac9116

Navigation menu

Versions of this User Manual:

Views

Navigation