Hwa Yao Technologies UTO-08-UTP-14 2.4G USB Dongle User Manual

Hwa Yao Technologies Co.,Ltd 2.4G USB Dongle Users Manual

Contents

User manual I

1
2.4GHz U-Tenna PANEL 14dBi
USER’S MANUAL
VERSION 2.0
2007/04/24
2
The installation & driver CD will automatically activate the autorun
installation program after you insert the disk into your CD drive.
Step 1 :
Insert the installation & driver
CD into your CD-ROM.
Step 2 :
Click Next to continue.
3
Step 3 :
Click Next to install at the
designated folder. Or, click
“Browse” to select different
folder.
Step 4 :
Start copying files until it
finishes the installation.
Step 5 :
Click Finish to complete
installation.
Step 6 :
After finished install driver and
utility on your system, plug the
USB adapter into the USB
port of your PC. Windows
XP/2000 will automatically
detect the USB Adapter.
4
WLAN USB Adapter uses its own management software. All functions
controlled by users are provided by this application. When you insert the
WLAN USB Adapter into the USB port of your PC, a new icon should
appear in the Windows System Tray automatically.
If the icon is in red, it means that WLAN USB Adapter configuration is
invalid or incomplete. Double click on that icon and the configuration
window will pop up as shown below. It shows the SSID of available
network. Once a network is chosen, the signal strength and link quality
are displayed.
The Link Quality and Signal Strength
bar chart is only active when the
node is in Infrastructure Mode. The
bar graph displays the quality and
strength of the link between the
node and its Access Point. Link
Quality is a measurement
of receiving and transmitting
performances over the radio.
Tx/Rx Frame displays the instantaneous wireless Transmit and Receive
Throughput in bytes per second, these values are updated every two seconds
The Configuration Tool contains several fields where operating parameters of
the driver can be viewed or changed. Changes to any of the parameters in this
panel can be applied to the driver without a need to restart the computer.
5
1. The installation & driver CD will automatically activate the autorun
installation program after you insert the disk into your CD drive. Please
refer to page 2”INSTALL DRIVER / UTILITY”
2. To install manually:
Plug your USB dongle into USB
interface, windows Vista will search
for compatible driver to install.
Step 1 :
Select “Locate and install the driver
software”, Windows will guide you
through the process of installing
driver software for your device.
Step 2 :
Insert the installation disc into the
CD-ROM and click “next” to continue
installation.
6
Step 3 :
Windows Vista search for the
software and it will be installed
successfully.
Step 4 :
After installation, right click the
network icon on the Windows Vista
System Tray, and click “Connect to a
network”.
7
Step 5 :
Select a network to connect to and
click “Connect”.
Step 6 :
Click “Connect Anyway” if the
network is an unsecured network.
Step 7:
USB Dongle successfully connected
to network, Click “Close”
8
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to
operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your
body.
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.

Navigation menu