Hyster P2 0S Users Manual Hys_P2.0SE P2.0S_ P2.#E053E

: Hyster Hyster-P2-0S-Users-Manual-566348 hyster-p2-0s-users-manual-566348 hyster pdf

Open the PDF directly: View PDF .
Page Count: 6

Download
Open PDF In Browser	View PDF

STRONG PARTNERS. TOUGH TRUCKS.

Powered pallet truck with folding platform
P2.0SE, P2.0S, P2.0SD

P2.0SE, P2.0S, P2.0SD

Specification Data is based on VDI 2198
Equipment and weight:
Weights (line 2.1) are based on the following specifications:
Complete truck with 170 mm wide forks. Polyurethane drive wheel and load rollers (P2.0SE).
Complete truck with 170 mm wide forks. Vulkollan drive wheel and load rollers (P2.0S).
Complete truck with 195 mm wide forks, Vulkollan drive wheel and load rollers (P2.0SD).

P2.0SE, P2.0S, P2.0SD

Forks:
P2.0SE:
P2.0S:
P2.0SD:

55 x 170 x 1 191 mm long
55 x 170 x 1 183 mm long
55 x 195 x 1 190 mm long

Fork spacing:
Inside to inside:
220 mm (P2.0SE-S), 180 mm (P2.0SD)
Outside to outside:
560 mm (P2.0SE-S), 570 mm (P2.0SD)
Other fork lengths and widths are optional.

NOTE:
The condition of the vehicle and how it
is equipped, as well as the nature and
condition of the operating area affect
specifications. If these specifications are
critical, the proposed application should
be discussed with your dealer.
Value or text in brackets are referred
to a truck equipped with fixed side (Biga) or
fixed back (Bob) protections.
‹

Values are referred to a P2.0S
equipped with Servo Power Steering
and battery compartment of 400 Ah
(300 Ah for P2.0S) with Fork b5 = 560
L = 1183

™

Speed with electric Servo Power
steering. For higher speed (12,5 km/h)
applications consult your TM - TC

z

Values determined by wheel friction,
if climbing ramps frequently (within 1 h),
consult your salesman

„

With mechanical steering 6/6 km/h
cause truck is without side gates, With
Optional fixed or foldable Side
protection 7,4/7,5 km/h

S

More forks dimensions see the table

{

Add 61 mm with fixed side
protection (Biga)
Add 110 mm with fixed back
protection (Bob)

†

Add 75 mm with fixed side

Ast = Wa + x + l6 + a (see lines 4.33 & 4.34)

protection (Biga)

a = Minimum operating clearance

Add with 114 mm fixed back
protection (Bob)

(V.D.I. standard = 200 mm BITA recommendation = 300 mm)
l6 = Load length

Ë

10/15 with fixed side protection (Biga),
10/14 with fixed back protection (Bob)

Notice
Care must be exercised when handling
elevated loads. When the carriage
and/or load is elevated, truck stability
is reduced. It is important that mast tilt
in either direction be kept to a
minimum when loads are elevated.
Operators must be trained and adhere
to the instructions contained in the
Operating Manual.

Hyster products are subject to change without notice.
Lift trucks illustrated may feature optional equipment.

Safety:
This truck conforms to the current EU requirements.

Product Features
 P2.0SE

Powered pallet truck with folding platform, mechanical steering.

 P2.0S

Powered pallet truck with folding platform, power steering.

 P2.0SD

Powered pallet truck with folding platform, double pallet handler.

Productivity
 Compact chassis design to improve accessibility.
 Operator-friendly tiller head controls for productive load handling.
 Regenerative braking and anti-rollback both available.
 Drive modes tailored around operation needs: pedestrian or stand-on, with or without side arms raised.
 Progressive speed control and steering system ensure optimum performance levels.
 Tandem load wheels and exit / entry rollers.
 Optional key-pad with PIN code for enhanced warehouse management.

Ergonomics
 Ergonomically designed tiller head for maximum operator comfort.
 Generously proportioned folding platform, with built-in suspension.
 Low effort controls ergonomically positioned to reduce operator fatigue.
 Dual lift/lower controls allow operation by either hand.
 Power steering on P2.0S models makes truck highly manoeuvrable.
 'Corner control' system reduces speed automatically when cornering.
 Adjustable performance settings to suit specific operating conditions.

Serviceability
 Brushless lift motor construction ensures low maintenance requirements.
 Built-in diagnostic system for preventative maintenance communication reduces downtime.
 Driver Diagnostic Interface (DDI) allows selection of appropriate performance settings for specific applications.
 CANbus technology for increased functionality, reliability and servicing.

Cost of ownership
 AC motor provides superior performance and reduced operation costs.
 Power transmission supplied via helicoidal gears, running in oil bath.
 IP54 standards control for protection against dust and water.
 Extended service intervals.
 High frequency on-board charger on SE models for quick on-site recharge.

Dependability
 MOSFET high frequency Combi controller for traction and hydraulic controls.
 Welded fork construction makes them highly resistant to torsion and heavy loads.
 Tough two-stage mast with high through-visibility on SD models.
 Hour meter and battery discharge indicator with lift interrupt fitted.
 Cold store protection for application to -30 °C.

Strong Partners, Tough Trucks,
for Demanding Operations Everywhere.
Hyster supplies a complete product range,
including Warehouse trucks, IC and Electric
Counterbalanced trucks, Container Handlers
and Reach Stackers.
Hyster is committed to being much more than a
lift truck supplier. Our aim is to offer a complete
partnership capable of responding to the full
spectrum of materials handling issues:
Whether you need professional consultancy on
your fleet management, fully qualified service
support, or reliable parts supply, you can
depend on Hyster.
Our network of highly trained dealers provides
expert, responsive local support. They can offer
cost-effective finance packages and introduce
effectively managed maintenance programmes
to ensure that you get the best possible value.
Our business is dealing with your materials
handling needs so you can focus on the
success of your business today and in the
future.

Hyster Europe, Flagship House, Reading Road North, Fleet, Hants GU51 4WD, England.
Tel: +44 (0) 1252 810261

Fax: +44 (0) 1252 770702

Email: info@hyster.co.uk

http://www.hyster.co.uk

A division of NACCO Materials Handling Limited.

05/07/TLC Printed in England
Form No. 901272/0

®
Hyster®,
, Vista® and Monotrol® are registered trademarks of Hyster Company in the United States and in certain other countries.
TM
, FortensTM, Pacesetter VSMTM, DuraMatchTM, DuraMatch PlusTM, TouchPointTM, TouchControlTM, EZXchange & HSMTM are trademarks
of Hyster Company in the United States and in certain other countries.
TM



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0.5 for Macintosh
Modify Date                     : 2007:05:21 15:48:36+01:00
Creator Tool                    : QuarkXPress™: LaserWriter 8.7.1 Z1-8.7.1
Create Date                     : 2007:05:21 15:41:29+01:00
Metadata Date                   : 2007:05:21 15:48:36+01:00
Format                          : application/pdf
Creator                         : Keith
Title                           : Hys_P2.0SE-P2.0S_ P2.#E053E.qxd
Document ID                     : uuid:fb6c8c17-07a9-11dc-a613-003065ed0b98
Instance ID                     : uuid:5aae1f52-07aa-11dc-af1c-003065ed0b98
Page Count                      : 6
Author                          : Keith

EXIF Metadata provided by EXIF.tools