Hyundai IBT A727 17" CRT Monitor User Manual

Hyundai IBT Corp. 17" CRT Monitor Users Manual

Users Manual

A727Mutiscanning Color Monitorwww.hyundaiQ.comUser's Guide
U.S.A.U.S.FEDERAL COMMUNICATIONS COMMISSIONRADIO FREQUENCY INTERFERENCE STATEMENTINFORMATION TO THE USERNOTE : This equipment has been tested and found to comply with the limits for aClass B digital device pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmfulinterference in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and, ifnot installed and used in accordance with the instructions, may cause harmfulinterference to radio communications.However, there is no guarantee that interference will not occur in a particularinstallation.If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the followingmeasures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet of a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for assistance.Changes or modification not expressly approved by the party responsible forcompliance could void the user's authority to operate the equipment.Connecting of peripherals requires the use of grounded shielded signal cables.
WE HYUNDAI ImageQuest CO., LTD.Ami-ri Bubal-Eub Ichon-Si Kyungki-Do467-860 KOREAdeclare under our sole responsibility that the product:to which this declaration relates is in conformity with thefollowing standard(s) or other normative document(s)following the provisions of the Low Voltage Directive 73/23/EEC,93/68/EEC and the EMC Directive 89/336/EEC.KOREA / Apr. 02, 2001 HONG KI, KIM(Place and date of issue) (Name and signature of authorized person)DECLARATION OF CONFORMITYKind of equipment : COLOR MONITORT ype-Designation : A727Safety : EN60950 : 1992 + A1, A2, A3, A4, A11EMC : EN 55022/1998, EN 55024: 1998EN 61000-3-2: 1995+A1 : 1998+A2 : 1998EN 61000-3-3: 1995Accredited testlaboratory:TÜV RheinlandAm Grauen Stein51105 Köln
A727 Multiscanning Color MonitorContents3-6. Setting the refresh rate.................8/19Preset Timing Table.......................8/194. Adjusting the picture.......................9/194-1. Using the On Screen Display.......10/194-2. Direct access buttons...................10/194-3. OSD Adjustments.........................11/195. Display power management.........15/19Reducing power consumption..........15/196. Troubleshooting.............................16/197. Specifications.................................19/191. Introduction ...............................1/192. Safety Information ...................1/193. Installing the monitor ..............3/193-1. Packing List ....................................3/193-2. Fastening the swivel and tilt base ...4/193-3. Selecting a suitable location..........4/193-4. Connecting the monitor.................5/193-5. Installing the driver........................7/193-5-1. Windows 95/98/2000...................7/193-5-2. Other operating systems.............8/19
A727 Multiscanning Color Monitor1/191. Introduction2. Safety InformationThis manual contains instructions for installing and operating NEC CI A727.NEC CI A727 is a highly ergonomic color display unit; • 17” diagonal (15.7” viewable) 0.27mm dot pitch CDT• Supporting high screen refresh rates and full scan flicker-free picture quality• With On Screen Display menus for user control• 100-240V AC input voltage• VESA DPMS (Display Power Management Signaling)• VESA DDC1/2B compatibilityWhen you set up and use your display unit, follow the safety instructions below.• Do not use the display unit in humid environments like bathrooms, dampcellars, swimming pools, etc.• This equipment must be connected to an earthed outlet which is close to thedisplay unit and accessible in case you need to disconnect the display.• Do not connect an extension cord.• Never insert objects into the openings on the outside of the device as you cancome into contact with live electrical components. This can cause fire or givestrong electrical shocks.• Slots in the cabinet are provided for ventilation. Do not block the ventilationslots in the display unit cabinet.• Do not under any circumstances open the display unit cabinet.
A727 Multiscanning Color Monitor2/19• To avoid risk of electric shock, do not disassemble the display unit cabinet. The unit is not user-serviceable. Remember to unplug the display unit from thepower outlet before cleaning.• Do not use alcohol (methyl, ethyl or isopropyl) or any strong dissolvent. Do notuse thinner or benzene, abrasive cleaners or compressed air.• Do not wipe the screen with a cloth or sponge that could scratch the surface.• To clean your antistatic screen, use water and a special microfiber screencleaning tissue used in optical lens cleaning, or lightly dampen a soft, cleancloth with water or a mild detergent.• To clean display unit cabinet, use a cloth lightly dampended with a milddetergent.• During the transportation of the monitor, the swivel base has to be removed inevery case.Cleaning and Maintenance
A727 Multiscanning Color Monitor3/19The following items should be found in the packaging.Above power cord can be changed upon different voltage areas. Pleasecontact your dealer if anything is missing or damaged.3. Installing the monitor3-1. Packing ListTilt and SwivelCompact DiscPower cordMonitorAttached Signal Cable!
A727 Multiscanning Color Monitor4/193-2. Fastening the swiveland tilt base3-3. Selecting a suitablelocation• Place the base against the bottom of the monitor so that the base fasteners arealigned with appropriate slots.• Push the base towards the front of the monitor until the latch locks intoposition.• Place the monitor at least 30cm from other electrical or heat-emittingequipment and allow at least 10cm on each side for ventilation.• Place the monitor in a position where no light shines directly onto or isreflected on the screen.• To reduce eye strain, avoid installing the display unit against a brightbackground such as a window.• Position the monitor so that the top of the screen is no higher than eye level.• Position the monitor directly in front of you at a comfortable reading distance(around 45 to 90cm)
A727 Multiscanning Color Monitor5/193-4. Connecting themonitor Before you start cabling your monitor, check thatthe power is off on all units. To avoid anypossibility of electric shock, always connect yourequipment to properly earthed outlets.!
A727 Multiscanning Color Monitor6/191. Insert the 15-pin signal cable connector to the VGA connection on yourcomputer and screw it down.2. Plug the display unit’s power cable first to the back of the display unit.3. Then plug the power cable to a 100V - 240V earthed electrical outlet or to thesystem unit, if it has an outlet for the display power cable.4. Turn on the display unit using the Soft power switch and check that the powerLED is on. If not, repeat steps 2, 3 and 4 or refer to the Troubleshooting sectionof this guide.5. Turn on the power to the computer. The picture will appear within about 15seconds. Adjust the picture to obtain optimum picture quality. See the sectionAdjusting the picture in this guide for more information.Soft Power SwitchPower LED
A727 Multiscanning Color Monitor7/19This monitor complies with Microsoft Windows Plug and Play standard. The monitor will be detected automatically when starting Windows 95/98 or 2000.1. Switch on the monitor.2. Start Windows. New hardware will be found (Plug and Play monitor) and the'Add New Hardware Wizard' will start up.3. Click on 'Next' to continue. 4. Follow the on-screeninstructions for installing theproper driver. Windows willlocate the driver for the Plugand Play monitor.5. Follow the on-screeninstructions for installing theproper driver.6. Select 'NEC CI A727'and click on 'Next' to continue.7. Follow on-screen instructions tocomplete the installation.The computer does not need to be restarted following installation.3-5. Installing the driver3-5-1. Windows95/98/2000Figure : Installing the driver
A727 Multiscanning Color Monitor8/193-5-2. Other operatingsystems3-6. Setting the refreshratePreset Timing TableNo drivers are required for other operating systems, such as DOS, Windows 3.1x or Windows NT.Follow the instructions below to set your refresh rate in Windows 98.1. Go to the configuration window (Start-Settings-Configuration window).2. Double click on the ‘Display’ icon.3. Click on the ‘Settings’ tab.4. Click on the ‘Advanced’ button.5. Click on ‘Adapter’ and select 85Hz from the list.6. Click on ‘Apply’ to accept the selected value.The recommended setting is a resolution of 800x600 and a refresh rate of 85Hz. * Recommended primary mode.No.12345678Resolution640 480640 480640 480720 400800 600*800 600 800 6001024 768*Horizontal Frequency31.5 KHz43.3 KHz50.0 KHz31.5 KHz46.8 KHz53.6 KHz63.9 KHz68.7KHzRefresh rate60 Hz85 Hz100 Hz70 Hz75 Hz 85 Hz100 Hz85 Hz91280X102463.9 KHz60Hz
A727 Multiscanning Color Monitor9/194. Adjusting the picture You can adjust the screen display by using the buttons located below the screen.
A727Multiscanning Color Monitor10/191. Push the MENU button to call the OSD to the screen. The resolution andfrequency are displayed at the top of the menu box for your information.2. Push the or button to choose the item you want to adjust. The selecteditem is highlighted.3. Push the SELECT button to adjust the highlighted item. 4. Use the or button to adjust the selection.5. Push the MENU button to return to the previous menu if you are in asubmenu.6. The display unit automatically saves the new settings in 3 to 4 seconds afteryour last adjustments and the menu disappears. You can also push the MENUbutton to make the menu disappear.Brightness : Use the button to select the brightness adjustment. Adjust with or button.Contrast : Use the button to select the contrast adjustment. Adjust with or button.4-1. Using the On ScreenDisplay 4-2. Direct access buttons
A727 Multiscanning Color Monitor11/194-3. OSD AdjustmentsYou can play the moviefile to see how to adjustthe picture image byclicking each icon or titlehereunder.The OSD adjustments available to you are listed below.H. SIZEAdjusts the horizontal size of the entire screen image.H. POSITIONAdjusts the horizontal position of the entire screen image.V. SIZEAdjusts the vertical size of the entire screen image.V. POSITIONAdjusts the vertical position of the entire screen image.PINCUSHIONIf the vertical sides of the picture curve in or bulge out, you can correctthe pincushion distortion by using this adjustment.TRAPEZOIDIf the picture is wider at the top or at the bottom, you can correct thetrapezoid distortion by using this adjustment.PARALLELIf the sides of the screen image are tilted, you can correct the paralleldistortion by using this adjustment.
A727 Multiscanning Color Monitor12/19PIN BALANCEIf the sides of the picture are bowed to the right or to the left, you cancorrect the pincushion balance by using this adjustment.V. MOIREClears vertical moire if a series of concentric circles or arcs appear on your screen.H. MOIREClears horizontal moire if a series of concentric circles or arcs appear on your screen.Moire is an interference pattern that makes the screen seem to havefaint lines. A picture that is rasterised or consists of (small) repeatingfigures is sensitive to moire interference. Strong colors are also liable tointensify moire. The moire pattern on the screen does not affect the printout of theimage.LANGUAGEYou can select the language in which adjustment menus are displayed.The following languages are available; English, French, German, Italian,Spanish, Swedish, Finnish, Danish and Portuguese.ROTATIONIf the entire screen image is tilted, you can correct the distortion by usingthis adjustment.
A727 Multiscanning Color Monitor13/19OSD H. POSITIONAdjusts the OSD menu’s horizontal position on the screen.OSD V. POSITIONAdjusts the OSD menu’s vertical position on the screen.COLOR CONTROL Color temperature affects the tint of theimage. With lower color temperatures theimage turns reddish and with highertemperatures bluish.There are three color settings available: 9300K,6500K or USER. With the USER setting you canset individual values for red, green and blue.RECALLIf you operate your display unit in a factory preset mode, this functiondeletes adjustments you made for size, position and shape, and restoresthe properties which have been set in the factory. If you operate yourdisplay unit in a user mode, this function has no effect except that thecontrast will be reset to the maximum value and the brightness to thecut-off level.INFORMATIONInformation shows horizontal and vertical sync polarity of current timingset.
A727 Multiscanning Color Monitor14/19DEGAUSSExternal magnetic fields may cause distortion or discoloration in thepicture. Demagnetizing takes place automatically when the display unitis switched on, and the unit normally maintains faultless color purityduring operation.If you have tilted, swiveled or moved the display unit, you can performdemagnetization. During this process the picture is distorted for a fewseconds. After demagnetizing, the color impurities have disappeared ifcaused by stray magnetic fields. Do not use the degauss feature more than once every half hour.BRIGHTNESSAdjusts the brightness of the screen.CONTRASTAdjusts the contrast of the screen.
A727 Multiscanning Color Monitor15/19If the power management function of your computer is enabled, your monitorturns on and off automatically. You can control power management features fromyour computer.Your computer may have power management features which enable the computeror monitor to enter a power saving mode when the system is idle. You canreactivate the system by pressing any key or moving the mouse.The power button does not disconnect the display unit from the mains. Theonly way to isolate the display unit completely from the mains supply is tounplug the mains cable.Power consumption90 W 15 W15 W5 W4 W0 WModeNormalStandbySuspendoffSoft Power Switch offUnplugged5. Display powermanagementReducing powerconsumption!LEDGreenAmberAmberAmberNot illuminatedNot illuminated
A727 Multiscanning Color Monitor16/196. TroubleshootingProblemBlank screenError message:OUT OF RANGESelf diagnosticsmessageNO SIGNALPossible solutionIf the power LED is not lit, push the power switch to turn themonitor on. If the display unit is powered through the computer,check that the computer is switched on.The display unit might be in standby mode. Push one of thekeyboard keys. Check that the keyboard is properly connected tothe computer.Check that the power cable is correctly connected to the display unitand to the power outlet. The graphics adapter is set for too high refresh rate or linefrequency. Select another display mode with lower frequencies incomputer.This message indicates that the signal is missing or faulty. Checkthat the signal cable connector is properly connected and that theconnection pins are not bent or damaged. If the connector is loose,tighten the connector's screws.If your monitor is not functioning properly, you may be able to solve the problemby reading followings.
A727 Multiscanning Color Monitor17/19Possible solutionThe video signal from the computer does not comply with VESADPMS standard. Either the computer or the graphics adapter is notusing the VESA DPMS power management function.The screen may seem to flicker when the refresh rate is less than75Hz. See the list of recommended modes in the section Presettiming table.If your color is not uniform, demagnetize the display unit asdescribed in the section Degause under OSD adjustments, and makesure that the display unit is at least 30cm from any other electricalequipment.Check that the signal cable connector is properly connected and thatthe connection pins are not bent or damaged. Try another colortemperature. If the picture has strong color defects, switch off the display unitand the computer.Make sure that other electrical devices are at least quality 30cmaway.Adjust the picture characteristics as described in the sectionAdjusting the picture.A problem with your graphics adapter or display unit. Contact yourservice representative.ProblemThe display does not enter power managementmodeScreen flickersColor defectsSize, position,shape or qualityunsatisfactoryDuplicatedimages
A727 Multiscanning Color Monitor18/19Contacting service If the above troubleshooting hints do not help you find a solution to the problem, contact an authorized service agent. If the monitor is sent for service, use the original package if possible.Unplug the display unit from the power outlet and contact a service agent when:• The monitor does not operate normally according to the operating instructions.• The monitor exhibits a distinct change in performance.• The monitor has been dropped or the cabinet has been damaged.• The monitor has been exposed to rain, or water or liquid has been spilled ontothe monitor.
A727 Multiscanning Color Monitor19/1917"(viewable size : 15.7")Dot pitch 0.27 mmAnti-Static, anti-glare, TCO treatment coated.factory preset area : 306X230 mm InfiniteR.G.B Analog, 15 pin D-subHorizontal : 30 to 70kHzVertical : 50 to 150Hz108MHz1280X1024@60Hz100-240 VAC 1.5A 90W VESA DPMSLower than EPA recommendationVESA DDC 1/2BH/V POSITION, H/V SIZE, PINCUSHION, TRAPEZOID,PARALLEL, PIN BALANCE, H/V- MOIRE, LANGUAGES,ROTATION, OSD H/V POSITION, COLOR CONTROL, RECALL,INFORMATION, DEGAUSS, BRIGHTNESS, CONTRASTTCOFCC Class B, CEcULus, TÜV-GS, DHHS, NEMKO, DEMKO,FIMKO, SEMKO0 ~35 O C13.7Kg unpacked, 16.0Kg packed404 X 408 X 420 mmPicture tubeDisplay areaNumber of colorInput signalsFrequency rateMaximum bandwidthMaximum resolutionInput voltagePower consumptionPower ManagementPlug & PlayOSD menuErgonomics,Safety and EMCOperating TemperatureWeightDimensions (W X H X D mm)• Specification is subject to change without notice for performance improvement.7. Specifications

Navigation menu