Hyundai IBT C17F05071 17" CRT Monitor User Manual

Hyundai IBT Corp. 17" CRT Monitor Users Manual

Users Manual

ImageQuest F771Perfectly Flat Color MonitorUser's GuideClickwww.hyundaiQ.comNEXTType No. C17F05071
U.S.A.U.S.FEDERAL COMMUNICATIONS COMMISSIONRADIO FREQUENCY INTERFERENCE STATEMENTINFORMATION TO THE USERNOTE : This equipment has been tested and found to comply with the limits for aClass B digital device pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmfulinterference in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and, ifnot installed and used in accordance with the instructions, may cause harmfulinterference to radio communications.However, there is no guarantee that interference will not occur in a particularinstallation.If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the followingmeasures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet of a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for assistance.Changes or modification not expressly approved by the party responsible forcompliance could void the user’s authority to operate the equipment.Connecting of peripherals requires the use of grounded shielded signal cables.BACKNEXT
WE ImageQuest CO., LTD.Ami-ri Bubal-Eub Ichon-Si Kyungki-Do467-860 KOREAdeclare under our sole responsibility that the product:to which this declaration relates is in conformity with thefollowing standard(s) or other normative document(s)following the provisions of the Low Voltage Directive 73/23/EEC,93/68/EEC and the EMC Directive 89/336/EEC.KOREA / SEP. 26, 2000 HONG KI, KIM (Place and date of issue) (Name and signature of authorized person)DECLARATION OF CONFORMITY BACKNEXTKind of equipment : COLOR MONITORT ype-Designation : C17F05071Safety :EN 60950 : 1992 + A1, A2, A3, A4, A11EMC : EN 55022 : 1998, EN 55024 : 1998EN 61000-3-2 : 1995+A1 : 1998+A2 : 1998EN 61000-3-3 : 1995Accredited testlaboratory:TÜV RheinlandAm Grauen Stein51105 Köln
F 771Perfectly Flat MonitorBACKNEXTContents 1. Introduction ..............................1/182. Safety Information ...................1/183. Installing the monitor ..............3/183-1. Packing List ...................................3/183-2. Fastening the swivel and tilt base ..4/183-3. Selecting a suitable location ........4/183-4. Connecting the monitor ...............5/183-5. Setting the refresh rate ................7/18Preset Timing Table ......................7/184. Adjusting the picture .....................8/184-1. Using the On-Screen-Display .......9/184-2. Direct access buttons ....................9/184-3. OSD Adjustments....................... 10/185. Display power management .......14/18Reducing power consumption .........14/186. Troubleshooting ...........................15/187. Specifications ...............................18/18
F 771Perfectly Flat Monitor1. Introduction2. Safety Information1/18BACKNEXTThis manual contains instructions for installing and operating ImageQuestF771. ImageQuest F771 is a highly ergonomic color display unit; • 17” diagonal Flat(16” viewable) 0.25mm dot pitch CDT• Supporting high screen refresh rates and full scan flicker-free picture quality• With On Screen Display menus for user control• 100-240V AC input voltage• VESA DPMS (Display Power Management Signaling)• VESA DDC1/2B compatibilityWhen you set up and use your display unit, follow the safety instructions below.• Do not use the display unit in humid environments like bathrooms, dampcellars, swimming pools, etc.• This equipment must be connected to an earthed outlet which is close to thedisplay unit and accessible in case you need to disconnect the display.• Do not connect an extension cord.• Never insert objects into the openings on the outside of the device as you cancome into contact with live electrical components. This can cause fire or givestrong electrical shocks.• Slots in the cabinet are provided for ventilation. Do not block the ventilationslots in the display unit cabinet.• Do not under any circumstances open the display unit cabinet.
F 771Perfectly Flat Monitor2/18BACKNEXT• To avoid risk of electric shock, do not disassemble the display unit cabinet. The unit is not user-serviceable. Remember to unplug the display unit from thepower outlet before cleaning.• Do not use alcohol (methyl, ethyl or isopropyl) or any strong solvent. Do notuse thinner or benzene, abrasive cleaners or compressed air.• Do not wipe the screen with a cloth or sponge that could scratch the surface.• To clean your antistatic screen, use water and a special microfiber screencleaning tissue used in optical lens cleaning, or lightly dampen a soft, cleancloth with water or a mild detergent.• To clean display unit cabinet, use a cloth lightly dampended with a milddetergent.• During the transportation of the monitor, the swivel base has to be removed inevery case.Cleaning and Maintenance
The following items should be found in the packaging.Above power cord can be changed upon different voltage areas. Pleasecontact your dealer if anything is missing or damaged.UKAmerica/CanadaJapanAustraliaKoreaEuropeSouth AfricaCompact DiscAttachedSignal CablePower cordF 771Perfectly Flat Monitor3/18BACKNEXT3. Installing the monitor3-1. Packing List!Tilt and SwivelMonitor
F 771Perfectly Flat Monitor4/18BACKNEXT3-2. Fastening the swiveland tilt base3-3. Selecting a suitablelocation• Place the base against the bottom of the monitor so that the base fasteners arealigned with appropriate slots.• Push the base towards the front of the monitor until the latch locks intoposition.• Place the monitor at least 30cm from other electrical or heat-emittingequipment and allow at least 10cm on each side for ventilation.• Place the monitor in a position where no light shines directly onto or isreflected on the screen.• To reduce eye strain, avoid installing the display unit against a brightbackground such as a window.• Position the monitor so that the top of the screen is no higher than eye level.• Position the monitor directly in front of you at a comfortable reading distance(around 45 to 90cm)
F 771Perfectly Flat Monitor5/18BACKNEXT3-4. Connecting themonitor Before you start cabling your monitor, check thatthe power is off on all units. To avoid anypossibility of electric shock, always connect yourequipment to properly earthed outlets.!P/C
Soft Power SwitchPower LEDF 771Perfectly Flat Monitor6/18BACKNEXT1. Insert the 15-pin signal cable connector to the VGA connection on yourcomputer and screw it down.2. Plug the display unit’s power cable first to the back of the display unit.3. Then plug the power cable to a 100V - 240V earthed electrical outlet or to thesystem unit, if it has an outlet for the display power cable.4. Turn on the display unit using the Soft power switch and check that the powerLED is on. If not, repeat steps 2, 3 and 4 or refer to the Troubleshootingsectionof this guide.5. Turn on the power to the computer. The picture will appear within about 15seconds. Adjust the picture to obtain optimum picture quality. See the sectionAdjusting the picture in this guide for more information.
F 771Perfectly Flat Monitor7/18BACKNEXT3-5. Setting the refreshratePreset Timing TableFollow the instructions below to set your refresh rate in Windows 98.1. Go to the configuration window (Start-Settings-Configuration window).2. Double click on the ‘Display’ icon.3. Click on the ‘Settings’ tab.4. Click on the ‘Advanced’ button.5. Click on ‘Adapter’ and select 85Hz from the list.6. Click on ‘Apply’ to accept the selected value.The recommended setting is a resolution of 800x600 and a refresh rate of 85Hz.No.12345678Resolution720 x 400640 x 480640 x 480800 x 600800 x 600*800 x 6001024 x 7681024 x 768*Refresh rate70 Hz85 Hz100 Hz75 Hz85 Hz100 Hz75 Hz85 HzHorizontal Frequency31.5 KHz43.3 KHz50.6 KHz46.9 KHz53.7 KHz63.9 KHz60.0 KHz68.7 KHz* Recommended primary mode.
F 771Perfectly Flat Monitor8/18BACKNEXT4. Adjusting the picture You can adjust the screen display by using the buttons located below the screen.
F 771Perfectly Flat Monitor9/18BACKNEXT1. Push the MENU button to call the OSD to the screen. The resolution andfrequency are displayed at the top of the menu box for your information.2. Push the or button to choose the item you want to adjust. The selecteditem is highlighted.3. Push the SELECT button to adjust the highlighted item. 4. Use the or button to adjust the selection.5. Push the MENU button to return to the previous menu if you are in asubmenu.6. The display unit automatically saves the new settings in 3 to 4 seconds afteryour last adjustments and the menu disappears. You can also push the MENUbutton to make the menu disappear.BRIGHTNESS Use the button to select the brightness adjustment. Adjust with or button.CONTRASTUse the button to select the contrast adjustment. Adjust with or button.4-1. Using the On ScreenDisplay 4-2. Direct access buttons
F 771Perfectly Flat Monitor10/18BACKNEXT4-3. OSD AdjustmentsYou can play the moviefile to see how to adjustthe picture image byclicking each icon or titlehereunder.The OSD adjustments available to you are listed below.H. SIZEAdjust the horizontal size of the entire screen image.H. POSITIONAdjust the horizontal position of the entire screen image.V. SIZEAdjust the vertical size of the entire screen image.V. POSITIONAdjust the vertical position of the entire screen image.PINCUSHIONIf the vertical sides of the picture curve in or bulge out, you can correctthe pincushion distortion by using this adjustment.TRAPEZOIDIf the picture is wider at the top or at the bottom, you can correct thetrapezoid distortion by using this adjustment.PARALLELIf the sides of the screen image are tilted, you can correct the paralleldistortion by using this adjustment.
F 771Perfectly Flat Monitor11/18BACKNEXTPIN BALANCEIf the sides of the picture are bowed to the right or to the left, you cancorrect the pincushion balance by using this adjustment.V. MOIREClears vertical moire if a series of concentric circles or arcs appear on your screen.H. MOIREClears horizontal moire if a series of concentric circles or arcs appear on your screen.Moire is an interference pattern that makes the screen seem to havefaint lines. A picture that is rasterised or consists of (small) repeatingfigures is sensitive to moire interference. Strong colors are also liable tointensify moire. The moire pattern on the screen does not affect the printout of theimage.LANGUAGEYou can select the language in which adjustment menus are displayed.The following languages are available; English, French, German, Italian,Spanish, Swedish, Finnish, Danish and Portuguese.ROTATIONIf the entire screen image is tilted, you can correct the distortion by usingthis adjustment.
F 771Perfectly Flat Monitor12/18BACKNEXTOSD H. POSITIONAdjust the OSD menu’s horizontal position on the screen.OSD V. POSITIONAdjust the OSD menu’s vertical position on the screen.COLOR CONTROL Color temperature affects the tint of theimage. With lower color temperatures theimage turns reddish and with highertemperatures bluish.There are three color settings available:9300K, 6500K or USER. With the USERsetting you can set individual values for red,green and blue.RECALLIf you operate your display unit in a factory preset mode, this functiondeletes adjustments you made for size, position and shape, and restoresthe properties which have been set in the factory. If you operate yourdisplay unit in a user mode, this function has no effect except that thecontrast will be reset to the maximum value and the brightness to thecut-off level.INFORMATIONInformation shows horizontal and vertical sync polarity of current timingset.
F 771Perfectly Flat Monitor13/18BACKNEXTDEGAUSSExternal magnetic fields may cause distortion or discoloration in thepicture. Demagnetizing takes place automatically when the display unitis switched on, and the unit normally maintains faultless color purityduring operation.If you have tilted, swiveled or moved the display unit, you can performdemagnetization. During this process the picture is distorted for a fewseconds. After demagnetizing, the color impurities have disappeared ifcaused by stray magnetic fields. Do not use the degauss feature more than once every half hour.CONTRASTAdjust the contrast of the screen.BRIGHTNESSAdjust the brightness of the screen.
F 771Perfectly Flat Monitor14/18BACKNEXT5. Display powermanagementReducing powerconsumption!Power consumption75 W 5 W5 W1 W0 WModeNormalSuspendoffSoft Power Switch offUnpluggedLEDGreenGreen/Orange blinking (0.5sec.)OrangeNot illuminatedNot illuminatedIf the power management function of your computer is enabled, your monitorturns on and off automatically. You can control power management features fromyour computer.Your computer may have power management features which enable the computeror monitor to enter a power saving mode when the system is idle. You canreactivate the system by pressing any key or moving the mouse.The power button does not disconnect the display unit from the mains. Theonly way to isolate the display unit completely from the mains supply is tounplug the mains cable.
F 771Perfectly Flat Monitor15/18BACKNEXT6. TroubleshootingProblemBlank screenError message:OUT OF RANGESelf diagnosticsmessageNO SIGNALPossible solutionIf the power LED is not lit, push the power switch to turn themonitor on. If the display unit is powered through the computer,check that the computer is switched on.The display unit might be in standby mode. Push one of thekeyboard keys. Check that the keyboard is properly connected tothe computer.Check that the power cable is correctly connected to the display unitand to the power outlet. The graphics adapter is set for too high refresh rate or linefrequency. Select another display mode with lower frequencies incomputer.This message indicates that the signal is missing or faulty. Checkthat the signal cable connector is properly connected and that theconnection pins are not bent or damaged. If the connector is loose,tighten the connector's screws.If your monitor is not functioning properly, you may be able to solve the problemby following the suggestions below :
F 771Perfectly Flat Monitor16/18BACKNEXTPossible solutionThe video signal from the computer does not comply with VESADPMS standard. Either the computer or the graphics adapter is notusing the VESA DPMS power management function.The screen may seem to flicker when the refresh rate is less than75Hz. See the list of recommended modes in the section Presettiming table.If your color is not uniform, demagnetize the display unit asdescribed in the section Degauss under OSD adjustments, and makesure that the display unit is at least 30cm from any other electricalequipment.Check that the signal cable connector is properly connected and thatthe connection pins are not bent or damaged. Try another colortemperature. If the picture has strong color defects, switch off the display unitand the computer.Make sure that other electrical devices are at least quality 30cmaway.Adjust the picture characteristics as described in the sectionAdjusting the picture.A problem with your graphics adapter or display unit. Contact yourservice representative.ProblemThe display does not enter power managementmodeScreen flickersColor defectsSize, position,shape or qualityunsatisfactoryDuplicatedimages
F 771Perfectly Flat Monitor17/18BACKNEXTContacting service If the above troubleshooting hints do not help you find a solution to the problem,contact an authorized service agent. If the monitor is sent for service, use theoriginal package if possible.Unplug the display unit from the power outlet and contact a service agent when:• The monitor does not operate normally according to the operating instructions.• The monitor exhibits a distinct change in performance.• The monitor has been dropped or the cabinet has been damaged.• The monitor has been exposed to rain, or water or liquid has been spilled ontothe monitor.
F 771Perfectly Flat Monitor18/18BACK17"(viewable size : 16")Dot pitch 0.25 mmAnti-Static, anti-glare, TCO treatment coated.factory preset area : 305X229 mm InfiniteR.G.B Analog, 15 pin D-subHorizontal : 30 to 70kHz, Vertical : 50 to 150Hz108 MHz1024X768@85Hz100 - 240 VAC, 1.5 A75W VESA DPMSLower than EPA recommendationVESA DDC 1/2BH/V SIZE, H/V POSITION, PINCUSHION, TRAPEZOID,PARALLEL, PIN BALANCE, H/V- MOIRE, LANGUAGES,ROTATION, OSD H/V POSITION, COLOR CONTROL, RECALL,INFORMATION, DEGAUSS, BRIGHTNESS, CONTRASTTCOFCC Class B, CE, cULus, TÜV-GS, DHHS, SEMKO0 ~ 40O C16.0Kg unpacked, 19.0Kg packed404 X 408 X 414 mmPicture tubeDisplay areaNumber of colorInput signalsFrequency rateMaximum bandwidthMaximum resolutionInput voltagePower consumptionPower ManagementPlug & PlayOSD menuErgonomics,Safety and EMCOperating TemperatureWeightDimensions (W X H X D mm)• Specification is subject to change without notice for performance improvement.7. Specifications

Navigation menu