Hyundai IBT Q15 15-inch LCD Monitor User Manual

Hyundai IBT Corp. 15-inch LCD Monitor Users Manual

Users Manual

NEXTType No. L15A0C060User’s GuideImageQuest Q15TFT LCD Color MonitorClickwww.hyundaiQ.com
U.S.A.U.S.FEDERAL COMMUNICATIONS COMMISSIONRADIO FREQUENCY INTERFERENCE STATEMENTINFORMATION TO THE USERNOTE : This equipment has been tested and found to comply with the limits for aClass B digital device pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmfulinterference in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and, ifnot installed and used in accordance with the instructions, may cause harmfulinterference to radio communications.However, there is no guarantee that interference will not occur in a particularinstallation.If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the followingmeasures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet of a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for assistance.Changes or modification not expressly approved by the party responsible forcompliance could void the user’s authority to operate the equipment.Connecting of peripherals requires the use of grounded shielded signal cables.BACKNEXT
WE ImageQuest CO., LTD.Ami-ri Bubal-Eub Ichon-Si Kyungki-Do467-860 KOREAdeclare under our sole responsibility that the product:to which this declaration relates is in conformity with thefollowing standard(s) or other normative document(s)following the provisions of the Low Voltage Directive 73/23/EEC,93/68/EEC and the EMC Directive 89/336/EEC.KOREA / April. 8, 2002 HONG KI, KIM(Place and date of issue) (Name and signature of authorized person)DECLARATION OF CONFORMITY BACKNEXTKind of equipment : COLOR MONITORT ype-Designation : L15A0C060Safety : EN 60950 : 1992 + A1, A2, A3, A4, A11EMC : EN 55022 : 1998, EN 55024 : 1998EN 61000-3-2 : 1995+A1 : 1998+A2 : 1998EN 61000-3-3 : 1995Accredited testlaboratory:TÜV RheinlandAm Grauen Stein51105 Köln
Q1515" TFT LCD Color MonitorBACKNEXTContents4. Adjusting the picture ..................11/194-1. Using the On Screen Display ...........12/194-2. Direct access buttons ........................12/194-3. OSD Adjustments .............................13/195. Display power management ......15/19Reducing power consumption ...............15/196. Troubleshooting ..........................16/197. Specifications ..............................19/191. Introduction ...................................1/192. Safety Information .......................1/193. Installing the monitor ..................4/193-1. Packing List .........................................4/193-2. Selecting a suitable location .............5/193-3. Connecting the monitor ....................5/19USB hub ..............................................7/193-4. Setting the refresh rate .....................8/19Preset Timing Table ............................9/193-5. User’s Environment ..........................10/19
Q1515" TFT LCD Color Monitor1. Introduction2. Safety Information1BACKNEXTThis manual contains instructions for installing and operating ImageQuest Q15.ImageQuest Q15 is a highly ergonomic color display unit.• 15" viewable XGA LCD• Supporting full scan flicker-free picture quality• With On Screen Display menus for user control• 100-240V AC input voltage• VESA DPMS (Display Power Management Signalling)• VESA DDC1/2B compatibility• High guality screen re-scaling capability• Fast and accurate auto adjustment• Most advanced image scaling• USB (Universal Serial Bus) hub• Supporting VESA Flat Panel Monitor Physical Mounting InterfaceThis Monitor has been engineered and manufactured to assure your safety. You can prevent serious electrical shock and other hazards by keeping in mind the following:Do not place anything wet on the monitor or the powercord. Never cover the ventilation openings with anymaterial and never touch them with metallic or inflammable materials.
Q1515" TFT LCD Color Monitor2BACKNEXTAvoid operating the monitor in extreme heat, humidity or areas affected by dust. Temperature : 5~35°CHumidity : 30~80RH Be sure to turn the monitor off before plugging thepower cord into the socket. Make sure that the powercord and the other cords are securely and rightlyconnected.Overloaded AC outlets and extension cords are dangerous, as are frayed power cords and broken plugs, which may cause electric shock or fire. Call your service technician for replacement.Do not use sharp tools such as a pin or a pencil near the monitor, as they may scratch the LCD surface.Do not use a solvent, such as benzene, to clean the monitor, as it will damage the LCD surface.
Q1515" TFT LCD Color MonitorCleaning and Maintenance • To avoid risk of electric shock, do not disassemble the display unit cabinet. Theunit is not user-serviceable. Remember to unplug the display unit from thepower outlet before cleaning.• Do not use alcohol (methyl, ethyl or isopropyl) or any strong dissolvent. Do notuse thinner or benzene, abrasive cleaners or compressed air.• Do not wipe the screen with a cloth or sponge that could scratch the surface.• To clean your antistatic screen, use water and a special microfiber screencleaning tissue used in optical lens cleaning, or lightly dampen a soft, cleancloth with water or a mild detergent.• If the instructions above do not help in removing stains, contact an authorizedservice agent. 3BACKNEXT
Q1515" TFT LCD Color Monitor4BACKNEXTThe following items should be found in the packaging.Above power cord can be changed upon different voltage areas. Pleasecontact your dealer if anything is missing or damaged.3. Installing the monitor3-1. Packing List!UKAmerican/CanadaJapanAustraliaKoreaEuropeSouth AfricaPower cordSignal cableAC/DC Power adapterUSB cable(Option)Compact Disc
Q1515" TFT LCD Color Monitor5BACKNEXT3-2. Selecting a suitablelocation3-3. Connecting the monitor• Place the monitor at least 30cm from other electrical or heat-emittingequipment and allow at least 10cm on each side for ventilation.• Place the monitor in a position where no light shines directly onto or isreflected on the screen.• To reduce eye strain, avoid installing the display unit against a brightbackground such as a window.• Position the monitor so that the top of the screen is no higher than eye level.• Position the monitor directly in front of you at a comfortable reading distance(around 45 to 90cm) Before you start cabling your monitor, check that thepower is off on all units. To avoid any possibility ofelectric shock, always connect your equipment toproperly earthed outlets.1. Insert the other 15-pin signal cable connector into the 15-pin VGA connectionon your computer and screw it down. 2. Plug the power cord connection to connection on the AC-DC Power adapter.3. Plug the jack of the AC-DC Power adapter connection to connection on monitor.4. Plug the other end of the power cord to your computer's main supply or to a100V-240V earthed electrical outlet.5. Turn on the monitor using the power switch and check that the power LED ison. If not, repeat steps 1,2,3 and 4 or refer to the Troubleshooting section ofthis guide.!!
Q1515" TFT LCD Color Monitor6BACKNEXT6. Turn on the power to the computer. The picture will appear within about 10seconds. Adjust the picture to obtain optimum picture quality. See sectionAdjusting the picture in this guide for more information.
Q1515" TFT LCD Color MonitorUSB hub (Optional)The USB hub(Bus-powered mode hub) have 1 upstream port and 2 downstreamports. The upstream port can be connected to the root hub of host PC or otherdownstream port. Two(2) downstream ports allow to connect another USBdevice such as USB mouse, joystick, printer etc.1) The maximum supply current of downstream port is 100mA each whenbus-powered mode hub.2) To activate the USB hub, your host system should have USB capability.7BACKNEXTUSB 2 downstream ports
Q1515" TFT LCD Color Monitor8BACKNEXT3-4. Setting the refreshrate Follow the instructions below to set your refresh rate in Windows 98/ME/XP/2000.1. Go to the configuration window(Start-Settings-Configuration window).2. Double click on the ‘Display’ icon.3. Click on the ‘Settings’ tab.4. Click on the ‘Advanced’ button.5. Click on ‘Adapter’ and select 60Hz from the list.6. Click on ‘Apply’ to accept the selected value.Power Switch / LED Indicator
Q1515" TFT LCD Color MonitorNo.12345678Resolution720 x 400640 x 480640 x 480800 x 600800 x 600*1024 x 7681024 x 7681024 x 768Horizontal Frequency31.5 KHz31.5 KHz37.9 KHz37.9 KHz46.9 KHz48.4 KHz56.5 KHz60.0 KHzRefresh rate70.1 Hz59.9 Hz72.8 Hz60.3 Hz75.0 Hz60.0 Hz70.1 Hz75.0 Hz* Recommended primary mode.Preset Timing Table If the signal from the system doesn't equal to the preset timing mode, adjustthe mode with reference to the user guide of videocard because the screenmay not be displayed.The recommended setting is a resolution of 1024x768 and a refresh rate of 60Hz.9BACKNEXT!
Q1515" TFT LCD Color Monitor3-5. User’s Environment With the double-hinge structure in the stand, this display unit is designed toSupport the following user s environment.• Without special Mounting Devices for VESA FPMPMI Standard, you can hangthis display unit on the wall by using 2 holes in the bottom side of stand likethe below picture.• You can fold the stand and the monitor by pushing STOPPER button.• You can adjust the tilt angle and height at your suitable level and can fold thestand during carriageIf you cannot fold the stand and the monitor fully, please pull the monitor abit and then follow the above instruction again.10BACKNEXT30 OPUSH!!
Q1515" TFT LCD Color Monitor4. Adjusting the picture11BACKNEXTYou can adjust the screen display by using the buttons located below thescreen.
Q1515" TFT LCD Color Monitor12BACKNEXT1. Push the MENU button to call the OSD to the screen. The resolution andfrequency are displayed at the top of the menu box for your information.2. Push the or button to choose the item you want to adjust. The selecteditem is highlighted.3. Push the SELECT button to adjust the highlighted item. 4. Use the or button to adjust the selection.5. Push the MENU button to return to the previous menu if you are in a submenu.6. The display unit automatically saves the new settings in 1 second after yourlast adjustments and the menu disappears. You can also push the MENU buttonto make the menu disappear.AUTO ADJUSTPush the button SELECT (AUTO) to adjust the shape of screenautomatically.BRIGHTNESS Use the button to select the brightness adjustment. Adjust with or button.CONTRASTUse the button to select the contrast adjustment. Adjust with or button.4-1. Using the On ScreenDisplay 4-2. Direct access buttons
Q1515" TFT LCD Color Monitor13BACKNEXT4-3. OSD AdjustmentsYou can play the movie file tosee how to adjust the pictureimage by clicking each icon ortitle hereunder.The OSD adjustments available to you are listed below.BRIGHTNESSAdjust the brightness of the screen.CONTRASTAdjust the contrast of the screen.COLOR CONTROLColor temperature affects the tint of the image. With lower color temperatures the image turns reddish and with higher temperatures bluish.There are three color settings available: Mode 1(a warm white), Mode 2(acool white) or USER. With the USER setting you can set individual valuesfor red, green and blue.H/V POSITIONH-POSITIONAdjusts the horizontal position of the entire screen image.V-POSITIONAdjusts the vertical position of the entire screen image.
Q1515" TFT LCD Color Monitor14BACKNEXTCLOCK PHASEPHASEAdjust the noise of the screen image.CLOCKAdjust the horizontal size of the entire screen image.AUTO ADJUSTYou can adjust the shape of screen automatically at the full screenpattern.MISCELLANEOUSRECALLRecall the saved color data.OSD TIMERYou can set the displayed time of OSD Menu window on the screen byusing this adjustment.OSD POSITIONAdjust the OSD menu's horizontal or vertical position on the screen.LANGUAGEYou can select the language in which adjustment menus are displayed. The following languages are available : English, French, German, Italian,Spanish, Swedish, Finnish, Danish, Portuguese and Dutch.
Q1515" TFT LCD Color MonitorIf the power management function of your computer is enabled, your monitorturns on and off automatically. You can control power management features fromyour computer.Your computer may have power management features which enable the computeror monitor to enter a power saving mode when the system is idle. You canreactivate the system by pressing any key or moving the mouse.The power button does not disconnect the monitor from the mains. The onlyway to isolate the monitor completely from the mains supply is to unplug themains cable.The power modes listed are for the monitor only and do not include any USBdevices connected to the USB ports.15BACKNEXT5. Display power managementReducing powerconsumption!Power consumption40 W5 W0 WModeNormaloffUnpluggedLEDGreenOrangeNot illuminated
Q1515" TFT LCD Color Monitor6. Troubleshooting16BACKNEXTProblemBlank screenError message:Video mode notsupportedThe display does not enter power managementmodePossible solutionIf the power LED is not lit, push the Soft power switch or check theAC cord to turn the monitor on. If the display unit is poweredthrough the computer, check that the computer is switched on.The display unit might be in standby mode. Push one of thekeyboard keys. Check that the keyboard is properly connected tothe computer.Check that the signal cable connector is properly connected and thatthe connection pins are not bent or damaged. If the connector isloose, tighten the connector's screws.Check that the power cable is correctly connected to the display unitand to the power outlet. Check the resolution and the frequency on the video port of yourcomputer.Compare these values with the data in the Preset Timing Table.The video signal from the computer does not comply with VESADPMS standard. Either the computer or the graphics adapter is notusing the VESA DPMS power management function.If your monitor is not functioning properly, you may be able to solve the problemby following the suggestions below :
Q1515" TFT LCD Color Monitor17BACKNEXTPossible solutionCheck that the signal cable connector is properly connected and thatthe connection pins are not bent or damaged. Try another colortemperature. Adjust the picture characteristics as described in the section OSDAdjustment(4-3).A problem with your graphics adapter or display unit. Contact yourservice representative.Check that the display resolution and frequency from your PC orgraphic adapter is an available mode for your monitor.In your PC, you can check through Control panel, Display, Settings.If the setting is not correct, use your computer utility program tochange the display settings.Check that the signal cabel connector is properly connected and thatthe connection pins are not bent or damaged.If the connector is loose, tighten the connector’s screws.Check that the computer is switched on.To enter a power saving mode. You can reactivate the system bypressing any key or moving the mouse.ProblemColor defectsSize, position,shape or qualityunsatisfactoryDuplicatedimagesImage is notstableMessage : No signalThe power LED is aorange color
Q1515" TFT LCD Color MonitorContacting service18BACKNEXTPossible solutionLED Indicator can be orange color on changing of video mode orInput Signal.Check the Resolution and the frequency on the video part of yourcomputer. Compare these values with the data in the Preset TimingTable.ProblemThe power LED is aorange colorIf the above troubleshooting hints do not help you find a solution to the problem,contact an authorized service agent. If the monitor is sent for service, use theoriginal package if possible.Unplug the display unit from the power outlet and contact a service agent when:• The monitor does not operate normally according to the operating instructions.• The monitor exhibits a distinct change in performance.• The monitor has been dropped or the cabinet has been damaged.• The monitor has been exposed to rain, or water or liquid has been spilled ontothe monitor.
Q1515" TFT LCD Color Monitor19BACK15"viewable, DiagonalPixel pitch 0.297 mm, A-Si TFT250cd/m2(Typ.)20msec304 X 228 mm16.2 million colorsR.G.B Analog, 15 pin D-subHorizontal : 31.0 to 60.0KHz, Vertical : 56 to 75Hz80 MHz1024X768@75HzDC 12V/5V 2.0A /2.0A40WVESA DPMSVESA DDC 1/2BBRIGHTNESS, CONTRAST, COLOR CONTROL, MISCELLANEOUS, AUTO ADJUST, LANGUAGE, H/V POSITION, CLOCK PHASE1up x 2down (Bus-Powered Hub)75 mm X 75 mm screw mountingTCO, FCC Class B, CE, cULus, TÜV-GS, SEMKO5 ~ 35O C3.5Kg unpacked, 5.0Kg packed350 X 357 X 201 mmLCDBrightnessResponse TimeDisplay areaNumber of colorInput signalsFrequency rateMaximum bandwidthMaximum resolutionInput voltagePower consumptionPower managementPlug & PlayOSD menuUSB (Optional)VESA FPMPMIErgonomics,Safety and EMCOperating TemperatureWeightDimensions (W X H X D mm)• Specification is subject to change without notice for performance improvement.7. Specifications

Navigation menu