I AM PLUS IAM5110 BT headset User Manual User s Guid by IAM

Download:
Mirror Download [FCC.gov]
Document ID	2757490
Application ID	mtWR4k53LR/0aYIl7ZUt3A==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	45.72kB (571480 bits)
Date Submitted	2015-09-22 00:00:00
Date Available	2015-09-22 00:00:00
Creation Date	2015-09-11 10:15:55
Producing Software	Acrobat Distiller 10.1.0 (Windows)
Document Lastmod	2015-09-11 10:15:55
Document Title	Microsoft Word - User's Guid by IAM+
Document Creator	PScript5.dll Version 5.2.2
Document Author:	ls

USER GUIDE
DOTS by i.am+
Bluetooth Headphones IAM5110
Visit PULS.com for support.
English User guide
Warning letter:
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
1.
2.
3.
4.
+ Button
• Power On 0 忏/ Pairing / Function Button
- Button
LED indicator
Micro USB(only for charging)
USB door
Microphone
What’s in the Box.
DOTS by i.am+ Bluetooth Headphones
Micro USB charging cable.
Quick Start Guide
User Guide
Warranty
Headphones operation
Item
Requirement and Description
Power On/Off
l Power On: Press and hold the Function button for 3 seconds. (release the
button after the blue LED bright, the red LED and blue LED start flashing means
the device enter pairing mode)
l Power Off: Press and hold the Function button until the red LED light up. Red
LED turn off means the device power off
Pairing
l First paring: Press and hold Function button for 3 sec. to power on, earphones
auto-enter pairing mode - LED alternates flashing Red and White.
l To paring with your PULS or phone, go to settings on your PULS or phone,
make sure Bluetooth is switched on.
l The ear-phones appears as “DOTS by i.am+” Select to pair.
l Bluetooth pairing after a successful first pairing:
n Power off then Press and hold Function button for 5 sec. to place earphones
in pairing mode - LED alternates flashing Red and White, mobile phone
search the Bluetooth device to connect the headphones (headphones ID is
“ DOTS by i.am+ ”
n If the earphones are outside Bluetooth range and disconnect from PULS or
your phone, the headphones will automatically try to re-connect. If
reconnection is unsuccessful for more than 5 mins, the headset will power
off.
l Set up use of DOTS headphones with multiple devices such as your PULS and
your smartphone.
1. Pair headphones to PULS or phone 1
2. Turn off the Bluetooth on PULS phone 1, and turn on Bluetooth on
phone 2
3. Search and pair the headset to phone 2
4. Turn on Bluetooth on PULS phone 1 and connect to headset
Charging
Open USB door “6” on controller and connect micro USB cable “5”
The headset will power off then enter charging mode - LED signal red while
charging
Solid white when full charge is reached
Use the Aneeda button on your PULS device to speak to and hear Aneeda on your
Using
Headphones headphones
with Aneeda
voice
assistant
LED
l LED turned off when headset powered off or not charging
Indication
Power on: white LED on 1s
Power off: red LED on 1s
Pairing: LED alternates flashing Red and White
Connected: white LED 0.1s on/4s off
Disconnected: white LED 0.1s on 2 times/2s off
Incoming call: white LED 0.5s on /0.5s off
Outgoing call: white LED 0.5s on /0.5s off
Active call: white LED 1s on /1s off
Music play: white LED 1s on /4s off
LED is changed from white blinking to Red blinking when battery low
l Charging：The headset will power off and enter charging mode - LED signal red
while charging, Solid white when full charge is reached.
Music Mode
Function
Status
Sound
indication
Operation
Volume up
Music or phone No
call mode
Press volume +
Volume
down
Play/Pause
Next song
Previous
song
Music or phone
call mode
Music mode
Music mode
Music mode
No
Press volume -
No
No
No
Short press Function button
Double press Function button
Phone
mode
call Answer call
Reject
incoming call
Hang
up
phone call
Switch call
between
headset and
phone
Mute
Incoming call
Incoming call
During
call
During
call
‘Beep’
once
No
phone ‘Beep’
one time
phone No
sound Press Function button 1 time
Press and hold Function button
for 2 seconds
sound Press Function button 1 time
During phone ‘Beep’ sound
call
two times
Cancel Mute During phone No
call
l Incoming call status:
Double press Function button
Fast press volume down button
for 2 times
Fast press volume up button for
2 times
n When mobile phone connected to headset through Bluetooth, mobile phone
will stop music player and play ring tone when have incoming call
n Mobile phone to resume playing music after hanging up phone call
l 3 party phone call:
- Short press Function button to connect the waiting phone call and hang off
current call
- Long press 1s the Function button to connect the waiting phone call and hold
current call. Long press 1s again to switch the two phone call status
DOTS by i.am+ Bluetooth Headphones Specification:
AptX for enhanced audio quality with PULS and compatible devices.
Up to 6hrs use time
Micro USB charging
Ip54 water resistance.
Frequency Response 20 ~ 20K Hz
Sensitivity 107 dB/mW
at 1KHz
Impedance 32 Ohm
Speaker driver
Magnet type
NdFeB
Distortion <1% at 1KHz
Music playback time 6hours
Batteries charging time 3hours
Battery typeLi-Polymer Battery
Bluetooth version v4.1
Bluetooth range 10m
Audio connection HSP, A2DP with aptX
Weight 18g
Hardware Version: 1.0
Software Version (FVIN): 1.0
Antenna Gain: 2.0dBi
Antenna Type: Ceramic
§ 15.19 Labeling requirements.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
§ 15.21 Information to user.
Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable
exposure condition without restriction.
This device complies with Industry Canada licenceexempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device m
ay not cause interference, and (2) This device must accept any interfer
ence, including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée
aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : ls
Create Date                     : 2015:09:11 10:15:55+08:00
Modify Date                     : 2015:09:11 10:15:55+08:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - User's Guid by IAM+
Creator                         : ls
Producer                        : Acrobat Distiller 10.1.0 (Windows)
Document ID                     : uuid:645116ab-19a4-4c90-9beb-8b467ccd7554
Instance ID                     : uuid:0e4267a6-9cb8-4bed-9633-fdbbace856e0
Page Count                      : 7

EXIF Metadata provided by EXIF.tools