ICOM orporated 328500 VHF Transceiver User Manual IC F3011 F3013 F4011 F4013 Instruction Manual

ICOM Incorporated VHF Transceiver IC F3011 F3013 F4011 F4013 Instruction Manual

Contents

User Manual

INSTRUCTION MANUALThis device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.UHF TRANSCEIVERSiF4000SeriesVHF TRANSCEIVERSiF3000Series
iFOREWORDREAD ALL INSTRUCTIONS carefully and completely before using the transceiver.SAVE THIS INSTRUCTION MANUAL— This instruction manual contains important operating instructions for the IC-F3001/IC-F3003/IC-F3006/IC-F3008 VHF TRANSCEIVERS and the IC-F4001/IC-F4003/IC-F4006/IC-F4008 UHF TRANSCEIVERS.EXPLICIT DEFINITIONSWORD DEFINITIONRDANGER Personal death, serious injury or an explo-sion may occur.RWARNING Personal injury, fire hazard or electric shock may occur.CAUTION Equipment damage may occur.NOTEIf disregarded, inconvenience only. No risk of personal injury, fire or electric shock.Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorpo-rated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries.
iiPRECAUTIONSCAUTION: NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 in.) away from the lips and the transceiver is vertical.CAUTION: NEVER operate the transceiver with a headset or other audio accessories at high volume levels.CAUTION: NEVER short the terminals of the battery pack.CAUTION: NEVER use non-Icom battery packs/chargers, to pre-vent the loss of the transceiver’s good performance and warranty.DO NOT push [PTT] when not actually intending to transmit.DO NOT use or place the transceiver in direct sunlight or in areas with temperatures below –30°C (+22°F) or above +60°C (+140°F). DO NOT modify the transceiver. The transceiver warranty does not cover any problems caused by unauthorized modification.KEEP the transceiver away from heavy rain, and never immerse it in the water. MAKE SURE the flexible antenna and battery pack are securely attached to the transceiver, and that the antenna and battery pack are dry before attachment. Exposing the inside of the transceiver to water will result in serious damage to the transceiver.MAKE SURE to turn the transceiver power OFF before con-necting the supplied/optional equipment.
iiiFCC INFORMATION• FOR CLASS B UNINTENTIONAL RADIATORS:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televi-sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.CAUTION: Changes or modifications to this device, not ex-pressly approved by Icom Inc., could void your authority to oper-ate this transceiver under FCC regulations.
ivTABLE OF CONTENTS 1234567891011121314151617181920FOREWORD ........................................................................................ iEXPLICIT DEFINITIONS ...................................................................... iPRECAUTIONS ................................................................................... iiFCC INFORMATION ...........................................................................iiiTABLE OF CONTENTS ...................................................................... iv1 ACCESSORIES ......................................................................... 1–4 ■ Supplied accessories .................................................................. 1 ■ Accessory attachments .............................................................. 12 PANEL DESCRIPTION ............................................................ 5–11 ■ Front, top and side panels .......................................................... 5 ■ LED indicator .............................................................................. 7 ■ Programmable function keys ......................................................83 BASIC OPERATION .............................................................. 12–22 ■ Turning power ON .....................................................................12 ■ Channel selection ..................................................................... 13 ■ Call procedure .......................................................................... 14 ■ Receiving and transmitting ....................................................... 15 ■ Setting the microphone gain ..................................................... 18 ■ Setting the squelch level ........................................................... 19 ■ Priority A channel selection ...................................................... 19 ■ MDC 1200 system operation .................................................... 20 ■ Emergency Call ........................................................................ 21 ■ Lone Worker Emergency Call ................................................... 224 BATTERY CHARGNING ........................................................ 23–30 ■ Caution (for BP-265 li-ion battery) .......................................... 23 ■ Caution (for the BP-264 ni-mh battery).................................... 26 ■ Optional battery chargers ......................................................... 285 BATTERY CASE .......................................................................... 31 ■ Optional battery case (BP-263) ................................................ 316 OPTIONS ............................................................................... 32–37 ■ VOX function ............................................................................. 357 SAFETY TRAINING INFORMATION ..................................... 38–39
■ Supplied accessoriesThe following accessories are supplied.Flexible antenna(This illustration is for the VHF type.)Battery packBelt clipJack cover(with screws)■ Accessory attachmentsD Flexible antennaConnect the flexible antenna to the an-tenna connector.CAUTION:• NEVER HOLD just the antenna when carrying the transceiver.• Transmitting without an antenna will damage the transceiver.11ACCESSORIES
21ACCESSORIES1234567891011121314151617181920D Belt clipTo attach the belt clip:➥ Slide the belt clip in the direction of the arrow until the belt clip locks in place, and makes a ‘click’ sound.Battery packTo detach the belt clip:q Remove the battery pack from the transceiver, if it is attached. (p. 3)w Lift the tab up (q), and slide the belt clip in the direction of the arrow (w).wqTab
31ACCESSORIESD Battery packTo attach the battery pack:q Fit the battery pack in the direction of the arrow (q), then close.w Hook the latch until it makes a ‘click’ sound (w).qBattery packLatchwTo remove the battery pack:Unhook the latch (e), and lift up the battery pack in the direction of the arrow (r).erNEVER remove or attach the battery pack when the transceiver is wet or soiled. This may result in water or dust getting into the transceiver/battery pack and may result in them being damaged.NOTE: Keep the battery pack terminals clean. It’s a good idea to clean the battery pack terminals once a week.
41ACCESSORIES1234567891011121314151617181920D Jack coverAttach the jack cover when the optional equipment is not used.To attach the jack cover:q Attach the jack cover to the [SP MIC] jack.w Tighten the screws.To detach the jack cover:e Remove the screws with a phillips screwdriver.r Detach the jack cover to con-nect the optional equipment.rwwqee
52PANEL DESCRIPTION■ Front, top and side panelsMicrophoneSpeakerrweqyuitLOWER KEYUPPER KEYPTT SWITCHANTENNACONNECTORROTARY SELECTORLED INDICATORVOLUME CONTROLSPEAKER-MICROPHONE JACKq ROTARY SELECTOR Rotate to select the pre-programmed memory channels.w VOLUME CONTROL [VOL] Rotate to turn the power ON/OFF, and adjust the audio level.
62PANEL DESCRIPTIONe LED INDICATOR (p. 7) ➥ Lights red* while transmitting. * When the optional battery case is attached, the LED indicator lights orange. ➥ Lights green while receiving a signal, or when the squelch is open. ➥ Lights/blinks orange when the matched 2/5-tone code is re-ceived, depending on the pre-programming.r SPEAKER-MICROPHONE JACK [SP MIC] Connect the optional speaker-microphone, earphone or VOX adapter cable.Jack coverNOTE: Attach the jack cover when the optional equip-ment is not used. (p. 4) t LOWER KEY [Lower]y UPPER KEY [Upper] The desired function can be assigned by your dealer. (p. 8)u PTT SWITCH [PTT]Push and hold to transmit; release to receive.i ANTENNA CONNECTOR Connect the antenna.1234567891011121314151617181920
72PANEL DESCRIPTION■ LED indicatorThe LED indicator indicates the status of various parameters of the transceiver as follows;(Ref.; R=Red, G=Green, O=Orange) R* R* TX Low BATT2 R* R* R* R*O O O O G G G G G GG G G G G G G G R G R G R G R G R G R G R G R GR O R O R O R O R O R O R O R O G G G Clone ErrClone TX/RXLow BATT1Low BATT2BusyF/S ScanCall LED BlinkCall LED ONTX Low BATT1 R* TX• TX: Lights Red while transmitting a signal.• RX: Lights Green while receiving a signal.• Call LED (ON): Turns ON while receiving a matched 2/5-tone.• Call LED (Blink): Blinks while receiving a matched 2/5-tone.• Fast/Slow scan: Blinks when the Fast/Slow scan is activated.• Low Battery 1: You should charge the battery. (blinks slowly)• Low Battery 2: You must charge the battery. (blinks fast)• TX low Battery 2: Very Low Battery was detected during TX mode.• Channel Error: A non-programmed channel is selected.* Lights (or blinks) orange when the optional battery case is attached.• TX low Battery 1: Low Battery was detected during TX mode.
82PANEL DESCRIPTION■ Programmable function keysThe following functions can be assigned to the [Upper] and [Lower] programmable function keys.Consult your Icom dealer or system operator for details concerning your transceiver’s programming.SCAN A➥ Push to start and cancel the scanning operation.➥ When the Power ON scan function is turned ON, push to pause the scanning operation. The paused scan resumes after the specified time period has passed.SCAN BPush to start and cancel the scanning operation.If the scan pauses for any reason, except being cancelled by this key, it will resume after a specified time period has passed.PRIORITY A CHANNEL, PRIORITY B CHANNELPush to select the Priority A or Priority B channel.PRIORITY A CHANNEL (REWRITE),PRIORITY B CHANNEL (REWRITE)➥ Push to select the Priority A or Priority B channel.➥ Push and hold [Prio A (Rewrite)] or [Prio B (Rewrite)] for 1 sec. to assign the operating channel to Priority A or Priority B chan-nel, respectively.MEMORY CHANNELS 1, 2, 3, 4Push to directly select memory channel 1, 2, 3 or 4, if programmed. Consult your dealer for details.1234567891011121314151617181920
92PANEL DESCRIPTIONMONITOR, MONITOR (AUDIBLE)➥ Push to turn the CTCSS (DTCS) or 2/5-tone squelch Mute ON or OFF. • Only during LMR operation, push to open any squelch func-tions, or deactivate any mute functions. • Only during PMR operation, push to activate one or two of the following functions* on each channel. - Push and hold to un-mute the channel (Audible condition). - Push to mute the channel (Inaudible condition). - Push to send a ‘reset code’ after the communication is finished. *Ask your dealer for details. NOTE: The un-mute condition may automatically return to the mute condition, after a specified time period.➥ Depending on the presetting, pushing and holding this key for 1 sec. cancels a scan.LOCKPush and hold to electronically lock all programmable keys except [Moni(Audi)], [Call] (including Call A and Call B), [Emergency], [Surveillance] and [Lone Worker].LONE WORKERPush to turn the Lone Worker function ON or OFF. (p. 22)• When the Lone Worker function is turned ON, and no operation is performed for the specified time period, the Emergency function is automatically turned ON.HIGH/LOWSelect the transmit output power temporarily or permanently, de-pending on the presetting.• Ask your dealer for the output power level for each selection.
102PANEL DESCRIPTIONTALK AROUND➥ Push to turn the Talk Around function OFF.➥ Push and hold to turn the Talk Around function ON. • The Talk Around function equalizes the transmit frequency to the receive frequency for transceiver-to-transceiver communication.WIDE/NARROW➥ Push to switch the IF bandwidth to Wide. • The wide passband width can be selected from 20 or 25 kHz using the optional cloning software (PMR operation only). Ask your dealer for details.➥ Push and hold to switch the IF bandwidth to Narrow.DTMF AUTODIALPush to transmit a programmed DTMF code.CALL, CALL A, CALL BPush to transmit a 2/5-tone code.• Tone call transmission may be necessary before you call another sta-tion, depending on your signalling system.• [Call A] and/or [Call B] keys may be available when your system em-ploys selective ‘Individual/Group’ calls. Ask your dealer which call is assigned to each key.1234567891011121314151617181920
EMERGENCYPush and hold for specified time period to transmit an emergency call.• The emergency call transmits with beeps, and the LED indicator lights red.• The transceiver can transmit an emergency call with no beep sound, and the LED indicator light. Ask your dealer for details.• If you want to cancel the emergency call, push and hold the key again before transmitting the call.• The emergency call is transmitted one time only, or repeatedly, until receiving an acknowledgement signal, or until is turned OFF. When a matched 5-tone code signal is received, the emergency function can be cancelled depending on the setting. (PMR operation only)SURVEILLANCEPush to turn the surveillance function ON or OFF.When this function is turned ON, the beep is not heard and the LED does not light when a signal is received, or a key is pushed.SIRENPush and hold for 1 sec. to emit a siren sound.This function can be used for situations other than an emergency alert, such as a security alarm for example.The transceiver emits the siren sound until the power is turned OFF.112PANEL DESCRIPTION
123BASIC OPERATION1234567891011121314151617181920■ Turning power ONPrior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation. (p. 23)➥Rotate [VOL] to turn power ON.D Battery operation type selectionThe battery operation type must be selected according to the attached battery type when the battery pack or case is replaced, and is used for the first time.Check the battery type before starting to select the battery opera-tion type. The beeps sound in sequence, so you must repeat the steps until the number of beeps matches your battery type.q Rotate [VOL] to turn the trans-ceiver power OFF.w While pushing and holding [PTT], rotate [VOL] to turn the power ON. • You should hold [PTT] until the beep sounds. (It takes approx. 5 sec.) • 1 beep sounds when the Li-Ion battery operation is selected. • 2 beeps sound when the battery case operation is selected. • 3 beeps sound when the Ni-MH battery operation is selected.e After the beep sounds, release [PTT].r Repeat steps q to e until you select the attached battery type.NOTE: This operation may not be available, depending on the presetting. Ask your dealer for details.[VOL][VOL][PTT]
■ Channel selectionSeveral types of channel selecting methods are available. They may differ, according to your system set up.To select a desired operating channel, do one of the following.• Rotate [ROTARY SELECTOR].• Push one of memory channel keys, [MR-CH 1] to [MR-CH 4].AUTOMATIC SCAN TYPE:Selecting a channel is not necessary for this type. When turning the power ON, the transceiver automatically starts scanning. Scanning stops when a call is received.NOTE: If the Move to Priority A channel at Power ON function (p. 19) is turned ON, the transceiver does not start scanning at power ON.133BASIC OPERATION
143BASIC OPERATION1234567891011121314151617181920■ Call procedureWhen your system employs tone signalling (excluding CTCSS and DTCS), the tone call procedure may be necessary prior to voice transmission. The tone signalling employed may be a selective call-ing system, which allows you to call only specific station(s), and prevent unwanted stations from contacting you.q Select a desired TX code channel or 2/5-tone code, according to your System Operator’s instructions. • This may not be necessary, depending on programming.w Push [Call] (assigned to one of the dealer programmable keys.) (p. 10)e After transmitting a 2/5-tone code, the remainder of your com-munication can be carried out normally.Selective calling Non-selective calling
153BASIC OPERATION■ Receiving and transmittingNOTE: Transmitting without an antenna will damage the trans-ceiver. See p. 1 for antenna attachment.Receiving:q Rotate [VOL] to turn power ON.w Rotate [ROTARY SELECTOR], or push one of the memory chan-nel keys, [MR-CH 1] to [MR-CH 4], to select a channel.e When receiving a call, adjust the audio output to a comfortable listening level.NOTE: When a matched RX code signal is received, audio from the microphone is automatically transmitted for a specified time period.** Depending on the presetting. Ask your dealer for details.Transmitting:Wait for the channel to become clear to avoid interference.q While pushing and holding [PTT], speak into the microphone at a normal voice level.w Release [PTT] to return to receive.IMPORTANT: To maximize the readability of your signal;1. Pause briefly after pushing [PTT].2. Hold the microphone 5 to 10 cm (2 to 4 inches) from your mouth, then speak into the microphone at a normal voice level.
163BASIC OPERATION1234567891011121314151617181920D Transmitting notes• Transmit inhibit functionThe transceiver has several inhibit functions, which restrict trans-mission under the following conditions:- The channel is muted.- The channel is busy.- A signal with the un-matched (or matched) CTCSS (or DTCS) tone is received.- The selected channel is a ‘receive only’ channel.• Time-out timerAfter continuously transmitting longer than the pre-programmed time period, the time-out timer activates, and stops further transmitting.• Penalty timerOnce the time-out timer activates, transmitting is further inhibited for a time period determined by the penalty timer.• PTTID callThe transceiver automatically sends the ID code (5-tone, DTMF, MDC system or digital ANI) when [PTT] is pushed (beginning of the transmission) and/or released (end of transmission), depending on the presetting.
D DTMF transmissionIf the transceiver has [DTMF Autodial] assigned to it, the automatic DTMF transmission function is usable.➥ Push [DTMF Autodial] to transmit the DTMF code.D Receiving a Stun and ReviveThe dispatcher can send a 2/5-tone signal that will stun or revive your transceiver. When a Stun command that matches your station ID is received, the Stun beep may sound*, and you can not receive or transmit. When a Revive command that matches your station ID is received, normal operation is restored.* Depending on the presetting. Ask your dealer for details.173BASIC OPERATION
■ Setting the microphone gainAdjusts the microphone gain.q Rotate [VOL] to turn the trans-ceiver power OFF.w While pushing and holding [Lower], rotate [VOL] to turn the power ON and enter the micro-phone gain adjustment mode.e Push [Upper] to increase, or push [Lower] to decrease the microphone gain. • The adjustable range is 1 (mini-mum) to 4 (maximum).r Rotate [VOL] to turn the power OFF, then ON to exit the micro-phone gain adjustment mode.NOTE: This operation may not be available, depending on the presetting. Ask your dealer for details.183BASIC OPERATION1234567891011121314151617181920[VOL][Upper][Lower]
■ Setting the squelch levelThe squelch circuit mutes the received audio signal, depending on the signal strength.q Rotate [VOL] to turn the trans-ceiver power OFF.w While pushing and holding [PTT] and [Lower], rotate [VOL] to turn the power ON and enter the squelch level adjustment mode.e Push [Upper] to increase the squelch level (tight squelch), or push [Lower] to decrease the squelch level (loose squelch). • The adjustable range is 0 (loose squelch) to 9 (tight squelch).r Rotate [VOL] to turn the power OFF, then ON to exit the squelch level adjustment mode.NOTE: This operation may not be available, depending on the presetting. Ask your dealer for details.■ Priority A channel selectionDepending on the presetting, the Priority A channel is selected each time the transceiver power is turned ON.193BASIC OPERATION[VOL][PTT][Upper][Lower]
■ MDC 1200 system operationThe MDC 1200 signaling system enhances your transceiver’s capabil-ities. It allows PTT ID*, Emergency signaling, and receiving Radio Check. Also, the dispatcher can stun and revive transceivers on the system.* When [PTT] is pushed and/or released, the transceiver transmits your station ID.D Transmitting an Emergency CallThe MDC 1200 system’s Emergency feature can be accessed using the [Emergency] key (p. 10). The transceiver will send an Emergency MDC 1200 system command once, or repeatedly for a programmed number of times until it receives the acknowledge-ment signal.The emergency call can be transmitted without a beep sound de-pending on how the emergency function is programmed. Ask your dealer for details.D Receiving a Stun and ReviveThe dispatcher can send MDC 1200 system signals that will stun or revive your transceiver. When a Stun command that matches your station ID is received, the Stun beep may sound*, and you can not receive or transmit. When a Revive command that matches your station ID is received, normal operation is restored.* Depending on the presetting. Ask your dealer for details.203BASIC OPERATION1234567891011121314151617181920
213BASIC OPERATION■ Emergency CallWhen [Emergency] is pushed for the specified time period*, the emergency signal is transmitted once, or repeatedly, on the speci-fied emergency channel.A repeat emergency signal is automatically transmitted until the transceiver receives an acknowledgement signal, or you turn the transceiver power OFF.When no emergency channel is specified, the signal is transmitted on the previously selected channel.If you want to cancel the emergency call, push and hold [Emer-gency] again before transmitting the call.If your transceiver is programmed for Silent operation, you can transmit an Emergency call without the beep sounding, and the LED indicator lighting.IMPORTANT: It is recommended to set an emergency channel individually to provide the certain emergency call operation.D NOTESDepending on the presetting, the following functions are automati-cally activated. Ask your dealer for details.• Auto TX functionAfter the emergency call transmission, audio from the microphone is automatically transmitted for a specified time period.*• Auto RX functionAfter the emergency call transmission, the transceiver stands by in the audible mode for the specified time period.** Depending on the presetting. Ask your dealer for details.
■ Lone Worker Emergency CallWhen the Lone Worker function is turned ON, and no operation is performed for the specified time period*, the transceiver enters the emergency mode, and then the countdown for the emergency call transmission starts.After the specified time period* has passed, an emergency call is automatically transmitted once, or repeatedly*.If someone operates the transceiver before the call is transmitted, the transceiver exits the emergency mode, and the emergency call is can-celled.➥Push [Lone Worker] to toggle the Lone Worker function ON or OFF.* Depending on the presetting. Ask your dealer for details.223BASIC OPERATION1234567891011121314151617181920
234BATTERY CHARGNING■ Caution (for the BP-265 li-ion battery)Misuse of Li-Ion batteries may result in the following hazards: smoke, fire, or the battery may rupture. Misuse can also cause damage to the battery or degradation of battery performance.R DANGER! Use and charge only specified Icom battery packs with Icom radios or Icom chargers. Only Icom battery packs are tested and approved for use with Icom radios or charged with Icom chargers. Using third-party or counterfeit battery packs or chargers may cause smoke, fire, or cause the battery to burst.D Battery cautionR DANGER! DO NOT hammer or otherwise impact the battery. Do not use the battery if it has been severely impacted or dropped, or if the battery has been subjected to heavy pressure. Battery damage may not be visible on the outside of the case. Even if the surface of the battery does not show cracks or any other damage, the cells inside the battery may rupture or catch fire.R DANGER! NEVER use or leave battery packs in areas with temperatures above +60˚C (+140˚F). High temperature buildup in the battery, such as could occur near fires or stoves, inside a sun heated car, or in direct sunlight may cause the battery to rupture or catch fire. Excessive temperatures may also degrade battery per-formance or shorten battery life.R DANGER! DO NOT expose the battery to rain, snow, seawater, or any other liquids. Do not charge or use a wet battery. If the bat-tery gets wet, be sure to wipe it dry before using. The battery is not waterproof.
244BATTERY CHARGING1234567891011121314151617181920R DANGER! NEVER incinerate used battery packs, since internal battery gas may cause them to rupture, or may cause an explosion.R DANGER! NEVER solder the battery terminals or NEVER mod-ify the battery pack. This may cause heat generation, and the bat-tery may rupture, emit smoke or catch fire.R DANGER! Use the battery only with the transceiver for which it is specified. Never use a battery with any other equipment, or for any purpose that is not specified in this instruction manual.R DANGER! If fluid from inside the battery gets in your eyes, blind-ness can result. Rinse your eyes with clean water, without rubbing them, and see a doctor immediately.R WARNING! Immediately stop using the battery if it emits an ab-normal odor, heats up, or is discolored or deformed. If any of these conditions occur, contact your Icom dealer or distributor.R WARNING! Immediately wash, using clean water, any part of the body that comes into contact with fluid from inside the battery.R WARNING! NEVER put the battery in a microwave oven, high-pressure container, or in an induction heating cooker. This could cause a fire, overheating, or cause the battery to rupture.CAUTION! Always use the battery within the specified temperature range for the transceiver (–30˚C to +60˚C; –22˚F to +140˚F) and the battery itself (–20˚C to +60˚C; –4˚F to +140˚F). Using the bat-tery out of its specified temperature range will reduce the battery’s performance and battery life.
CAUTION! Shorter battery life could occur if the battery is left fully charged, completely discharged, or in an excessive temperature environment (above +50˚C; +122˚F) for an extended period of time. If the battery must be left unused for a long time, it must be de-tached from the radio after discharging. You may use the battery until the remaining capacity is about half, then keep it safely in a cool dry place within the temperature range as shown below: –20˚C to +50˚C (–4˚F to +122˚F) (up to a month) –20˚C to +35˚C (–4˚F to +95˚F) (up to three months) –20˚C to +20˚C (–4˚F to +68˚F) (up to a year)D Charging cautionR DANGER! NEVER charge the battery pack in areas with ex-tremely high temperatures, such as near fires or stoves, inside a sun heated car, or in direct sunlight. In such environments, the safety/protection circuit in the battery will activate, causing the bat-tery to stop charging.R WARNING! DO NOT charge or leave the battery in the battery charger beyond the specified time for charging. If the battery is not completely charged by the specified time, stop charging and re-move the battery from the battery charger. Continuing to charge the battery beyond the specified time limit may cause a fire, overheat-ing, or the battery may rupture.R WARNING! NEVER insert the transceiver (battery attached to the transceiver) into the charger if it is wet or soiled. This could corrode the battery charger terminals or damage the charger. The charger is not waterproof.CAUTION! DO NOT charge the battery outside of the specified temperature range: BC-193 (0˚C to +40˚C; +32˚F to +104˚F). Icom recommends charging the battery at +20˚C (+68˚F). The battery may heat up or rupture if charged out of the specified temperature range. Additionally, battery performance or battery life may be re-duced.254BATTERY CHARGING
264BATTERY CHARGING1234567891011121314151617181920■ Caution (for the BP-264 ni-mh battery)• CAUTION! NEVER short terminals (or charging terminals) of the battery pack. Also, current may flow into nearby metal objects such as a necklace, so be careful when placing battery packs (or the transceiver) in handbags, etc.Simply carrying with or placing near metal objects such as a neck-lace, etc. may cause shorting. This may damage not only the bat-tery pack, but also the transceiver.• NEVER incinerate used battery packs. Internal battery gas may cause an explosion.• NEVER immerse the battery pack in water. If the battery pack becomes wet, be sure to wipe it dry BEFORE attaching it to the transceiver.• Clean the battery terminals to avoid rust or misscontact.• Keep battery contacts clean. It’s a good idea to clean battery ter-minals once a week.If your Ni-MH battery pack seems to have no capacity, even after being charged, completely discharge it by leaving the power ON overnight. Then, fully charge the battery pack again. If the battery pack still does not retain a charge (or only very little charge), a new battery pack must be purchased. (p. 32)Prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation.• Recommended temperature range for charging: between +10°C +40°C (rapid charge: with BP-191) or between 0°C and +45°C (regular charge: with BP-192)• Use the supplied charger or optional charger (BC-191 for rapid charging, BC-192 for regular charging) only. NEVER use other manufacturers’ chargers.
274BATTERY CHARGINGThe battery pack contains a rechargable battery.Charge the battery pack before first operating the transceiver, or when the battery pack becomes exhausted.If you want to prolong the battery life, the following points should be observed:• Avoid over charging. The charging time period should be less than 48 hours.• Use the battery pack until it becomes almost completely ex-hausted, under normal conditions. We recommend battery charg-ing after transmitting becomes impossible.D Battery pack lifeWhen the operating time becomes extremely short, even after charging the battery pack fully, a new battery pack is needed.
284BATTERY CHARGING1234567891011121314151617181920■ Optional battery chargersD Rapid charging with the BC-191The optional BC-191 provides rapid charging of the Ni-MH battery pack. Charging time period: Approx. 2.5 hours (for the BP-264)The following items are additionally required:• An AC adapter (not supplied with some versions) or the DC power cable (OPC-515L/CP-23L).Optional OPC-515L (for 13.8 V power source) or CP-23L (for 12 V cigarette lighter socket) can be used instead of the AC adapter.Charge indicator• Lights orange: While charging• Lights green: Charging is completed.AC adapter(A different type, or no AC adapt-er is supplied, depending on the version.)Battery pack TransceiverTurn power OFFIMPORTANT!Ensure the tabs on the battery pack are correctly aligned with the guide rails inside the charger adapter.Guide railTabsM3.5 × at least 30mm; Purchase separately)Screws*(*Using screws is rec-ommended to secure the charger.
294BATTERY CHARGINGD Regular charging with the BC-192The optional BC-192 provides regular charging of the Ni-MH bat-tery pack. Charging time period: Approx. 16 hours (for the BP-264)The following item is additionally required:• An AC adapter (not supplied with some versions)Charge indicatorLights orange while charging.AC adapter(A different type, or no AC adapt-er is supplied, depending on the version.)Battery pack TransceiverTurn power OFFIMPORTANT!Ensure the tabs on the battery pack are correctly aligned with the guide rails inside the charger adapter.Guide railTabsM3.5 × at least 30mm; Purchase separately)Screws*(*Using screws is rec-ommended to secure the charger.
304BATTERY CHARGING1234567891011121314151617181920D Rapid charging with the BC-193The optional BC-193 provides rapid charging of the Li-Ion battery pack. Charging time period: Approx. 3 hours (for the BP-265)The following items are additionally required:• An AC adapter (not supplied with some versions) or the DC power cable (OPC-515L/CP-23L).Optional OPC-515L (for 13.8 V power source) or CP-23L (for 12 V cigarette lighter socket) can be used instead of the AC adapter.Charge indicator• Lights orange: While charging• Lights green: Charging is completed.AC adapter(A different type, or no AC adapt-er is supplied, depending on the version.)Battery pack TransceiverTurn power OFFIMPORTANT!Ensure the tabs on the battery pack are correctly aligned with the guide rails inside the charger adapter.Guide railTabsM3.5 × at least 30mm; Purchase separately)Screws*(*Using screws is rec-ommended to secure the charger.
315BATTERY CASE■ Optional battery case (BP-263)When using the optional battery case, install 6 × (LR6) size alkaline batteries, as illustrated below.q Remove the battery case if it is attached. (p. 3)w Install 6 × AA (LR6) size alkaline batteries, as shown below. • Install only alkaline batteries. • Be sure to observe the correct polarity.e Attach the battery case. (p. 3)CAUTION:• When installing batteries, make sure they are all the same brand, type and capacity. Also, do not mix new and old batter-ies together.• Keep battery contacts clean. It’s a good idea to clean battery terminals once a week.• Never incinerate used battery cells since internal battery gas may cause them to rupture.• Never expose a detached battery case to water. If the battery case gets wet, be sure to wipe it dry before using it.NOTE: When the optional battery case is attached, the battery type must be selected as “Alkaline battery operation” when turn-ing the transceiver ON. Ask your dealer for details.
326OPTIONS1234567891011121314151617181920D BATTERY PACKBattery pack Voltage Capacity Battery life*1BP-264 7.2 V 1400 mAh VHF 14.1 hrs.UHF 13.7 hrs.BP-265 7.4 V 1900 mAh (min.)2000 mAh (typ.)VHF 20.2 hrs.UHF 19.6 hrs.BP-263 Battery case for AA (LR6) × 6 alkaline —*2*1 When the power save function is turned ON, and the operating time is calculated under the following conditions; TX : RX : standby = 5 : 5 : 90*2 The average operating time depends on the alkaline cells used.D CHARGERS• BC-191 desktop charger + BC-123S ac adapter For rapid charging of the Ni-MH battery pack. An AC adapter is supplied with the charger, depending on the version. Charging time: approx. 2.5 hours for the BP-264.• BC-192 desktop charger + BC-147S ac adapter For regular charging of the Ni-MH battery pack. An AC adapter is supplied with the charger, depending on the version. Charging time: approx. 16 hours for the BP-264.• BC-193 desktop charger + BC-123S ac adapter For rapid charging of the Li-Ion battery pack. An AC adapter is supplied with the charger, depending on the version. Charging time: approx. 3 hours for the BP-265.
D DC CABLES• CP-23L cigarette lighter cable Allows charging of the battery pack through a 12 V cigarette lighter socket. (For BC-191/BC-193)• OPC-515L dc power cable Allows charging of the battery pack using a 13.8 V power source instead of the AC adapter. (For BC-191/BC-193)D BELT CLIPS• MB-124 belt clip Exclusive alligator-type belt clip.D ANTENNAS• FA-SC73US/FA-SC56VS/FA-SC57VS stubby antennas FA-SC73US: 450–490 MHz FA-SC56VS: 150–162 MHz FA-SC57VS: 160–174 MHz• FA-SC25U/FA-SC57U/FA-SC72U/ FA-SC25V/FA-SC55V antennas FA-SC25U: 400–430 MHz FA-SC57U: 430–470 MHz FA-SC72U: 470–520 MHz FA-SC25V: 136–155 MHz FA-SC55V: 146–174 MHz• FA-SC61VC/FA-SC61UC cut antennas FA-SC61VC: 136–174 MHz FA-SC61UC: 380–520 MHz336OPTIONS
346OPTIONS1234567891011121314151617181920D OTHER OPTIONS• SP-13 earphone Provides clear audio in noisy environment.• AD-98FSC antenna connector converter Allows you to connect an external antenna with a BNC connector.• HM-153L/HM-166L earphone-microphone• HM-131L/HM-159L speaker-microphone Combination speaker-microphone that provides convenient op-eration while hanging the transceiver on your belt.• HS-94/HS-95/HS-97 headset + OPC-2004 plug adapter cable HS-94 : Ear hook type HS-95 : Neck-arm type HS-97 : Throat microphone OPC-2004 : Allows you to connect the HS-94 to the transceiver. After connection, the VOX function can be used.Approved Icom optional equipment is designed for optimal performance when used with an Icom transceiver.Icom is not responsible for the destruction or damage to an Icom trans-ceiver in the event the Icom transceiver is used with equipment that is not manufactured or approved by Icom.Some options may not be available in some countries. Please ask your dealer for details.
356OPTIONS■ VOX functionThe transceiver has a VOX function, which allows you hands-free operation.An optional headset (HS-94/HS-95/HS-97) and a plug adapter cable (OPC-2004) are additionally required for operation.• The VOX (voice operated transmission) function starts transmitting when you speak into the microphone, without needing to push the PTT switch; then, automatically returns to receive when you stop speaking.D Optional unit connectionq Rotate [VOL] to turn the transceiver power OFF.w Remove the jack cover. (p. 4)e Connect the optional HS-94, HS-95 or HS-97 and OPC-2004 as described below.HS-94OPC-2004qwe[VOL]
366OPTIONS1234567891011121314151617181920D Turning the VOX function ON or OFFThe VOX function can be turned ON or OFF when turning the trans-ceiver ON.q Connect the optional HS-94 and OPC-2004. (p. 35)w Rotate [VOL] to turn the trans-ceiver power OFF.e While pushing and holding [Up-per], rotate [VOL] to turn the power ON. • 1 beep sounds when the VOX function is turned OFF. • 2 beeps sound when the VOX function is turned ON.NOTE: This operation may not be available, depending on the presetting. Ask your dealer for details.[VOL][Upper]
376OPTIONSD Setting the VOX gainThe VOX sensitivity level can be adjusted from 1 (minimum) to 10 (maximum).q Connect the optional HS-94 and OPC-2004. (p. 35)w Rotate [VOL] to turn the trans-ceiver power OFF.e While pushing and holding [PTT] and [Upper], rotate [VOL] to turn the power ON and enter the VOX gain adjustment mode.r Push [Upper] to increase, or push [Lower] to decrease the VOX gain while speaking into the optional headset. • The adjustable range is 1 (mini-mum) to 10 (maximum).t Rotate [VOL] to turn the power OFF, then ON to exit the VOX gain adjustment mode.NOTE: This operation may not be available, depending on the presetting. Ask your dealer for details.[VOL][PTT][Upper][Lower]
W AR N INGYour Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during the course of employment by indi-viduals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment.This radio has been tested and complies with the FCC RF exposure limits for “Occupational Use Only”. In addition, your Icom radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans: • FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. • American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Fre-quency Electromagnetic Fields, 3 kHz to 300 GHz. • American National Standards Institute (C95.3-1992), IEEE Recom-mended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields– RF and Microwave. • The accessories (antennas, batteries, belt clips, speaker-micro-phone, etc. that is listed on pages 32–34) are authorized for use with this product. Use of accessories other than those specified may result in RF exposure levels exceeding the FCC requirements for wireless RF exposure.C AU TIO NTo ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for occu-pational use, always adhere to the following guide-lines:387SAFETY TRAINING INFORMATION1234567891011121314151617181920
397SAFETY TRAINING INFORMATION • DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio. • DO NOT transmit for more than 50% of total radio use time (“50% duty cycle”). “50% duty cycle” is also applicable to VOX/PTT mode. Transmitting more than 50% of the time can cause FCC RF expo-sure compliance requirements to be exceeded. The radio is trans-mitting when the “LED indicator” lights red. You can cause the radio to transmit by pressing the “PTT” switch or VOX function. • ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting and only use the Icom belt-clip which is listed on page 33 when attaching the radio to your belt, etc., to en-sure FCC RF exposure compliance requirements are not exceeded. To provide the recipients of your transmission the best sound qual-ity, hold the antenna at least 5 cm (2 inches) from your mouth, and slightly off to one side.The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to as-sure that this radio operates with the FCC RF exposure limits of this radio.Electromagnetic Interference/CompatibilityDuring transmissions, your Icom radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electro-magnetic radiation such as hospitals, aircraft, and blasting sites.Occupational/Controlled UseThe radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure.
MEMO1234567891011121314151617181920
MEMO
MEMO1234567891011121314151617181920
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, JapanA-6797H-1EXPrinted in Japan© 2009 Icom Inc.Printed on recycled paper with soy ink.

Navigation menu