ICOM orporated 366501 UHF Digital Transceiver User Manual 2

ICOM Incorporated UHF Digital Transceiver 2

Contents

User Manual 2

Download: ICOM orporated 366501 UHF Digital Transceiver User Manual 2
Mirror Download [FCC.gov]ICOM orporated 366501 UHF Digital Transceiver User Manual 2
Document ID2294779
Application IDiNf7c81izlQmLgx/Zl0niQ==
Document DescriptionUser Manual 2
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize27.09kB (338656 bits)
Date Submitted2014-06-13 00:00:00
Date Available2014-09-01 00:00:00
Creation Date2017-10-22 09:52:14
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-10-22 09:52:14
Document TitleUser Manual 2
Document CreatorAdobe InDesign CS3_J (5.0.4)

FCC INFORMATION
PRECAUTIONS
VHF DIGITAL TRANSCEIVER
Iç-F5360D
UHF DIGITAL TRANSCEIVER
Thank you for choosing the IC-F5360D VHF DIGITAL
or IC-F6360D UHF DIGITAL TRANSCEIVER.
READ ALL PRECAUTIONS carefully and completely before using your transceiver.
Iç-F6360D
TRANSCEIVER
EXPLICIT DEFINITIONS
WORD
Personal death, serious injury or an explosion may occur.
RWARNING!
Personal injury, fire hazard or electric shock may occur.
NOTE
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause
harmful interference.
DEFINITION
RDANGER!
CAUTION
•฀FOR฀CLASS฀A฀UNINTENTIONAL฀RADIATORS:
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
CAUTION:
Changes or modifications to this transceiver, not expressly
approved by Icom Inc., could void your authority to operate
this transceiver under FCC regulations.
Equipment damage may occur.
If disregarded, inconvenience only. No risk of personal injury, fire or electric shock.
PRECAUTIONS
RWARNING! NEVER connect the radio to an AC outlet.
This may pose a fire hazard or result in an electric shock.
RWARNING! NEVER connect the radio to a power
DO NOT operate the radio without running the vehicle’s engine. The vehicle’s battery will quickly run out when the radio
transmits while the vehicle’s engine is OFF.
source of more than 16 V DC such as a 24 V battery. This
will ruin the radio.
DO NOT place the radio in excessively dusty environ-
RWARNING! NEVER cut the DC power cable between
the DC plug and fuse holder. If an incorrect connection is
made after cutting, the radio might be damaged.
DO NOT place the radio against walls. Otherwise heat dis-
RWARNING! NEVER place the radio where normal
operation of the vehicle may be hindered or where it could
cause bodily injury.
ments.
sipation will be obstructed.
DO NOT use chemical agents such as benzine or alcohol
when cleaning, as they damage the radio surfaces.
BE CAREFUL! The radio will become hot when operating
continuously for long periods.
CAUTION: NEVER allow children to touch the radio.
CAUTION: NEVER expose the radio to rain, snow or any
liquids.
• POUR LES RAYONNEMENTS NON INTENTIONNELS
DE CLASSE A:
Cet équipement a été testé et reconnu conforme aux limites
ixées pour un appareil numérique de classe A, conformément au point 15 de la réglementation FCC.
Ces limites assurent une protection raisonnable contre les
interférences nuisibles lorsque l'équipement est utilisé dans
un environnement commercial. Cet équipement génère une
énergie de radio fréquence, utilise et rayonner et s'il n'est
pas installé et utilisé conformément au manuel d'instruction,
peut causer des interférences nuisibles aux communications radio. Le fonctionnement de cet équipement dans une
zone résidentielle est susceptible de causer des interférences nuisibles lorsque l'utilisateur doit corriger les interférences à ses propres frais.
Cet appareil respecte les conditions établies au paragraphe
15 des règles de la FCC. Son utilisation est assujettie à la
condition de ne pas provoquer des interférences nuisibles.
COUNTRY CODE LIST
•฀ISO 3166-1
10
11
12
13
14
15
16
17
Country
Austria
Belgium
Bulgaria
Croatia
Czech Republic
Cyprus
Denmark
Estonia
Finland
France
Germany
Greece
Hungary
Iceland
Ireland
Italy
Latvia
Codes
AT
BE
BG
HR
CZ
CY
DK
EE
FI
FR
DE
GR
HU
IS
IE
IT
LV
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Country
Liechtenstein
Lithuania
Luxembourg
Malta
Netherlands
Norway
Poland
Portugal
Romania
Slovakia
Slovenia
Spain
Sweden
Switzerland
Turkey
United Kingdom
Codes
LI
LT
LU
MT
NL
NO
PL
PT
RO
SK
SI
ES
SE
CH
TR
GB
< Intended Country of Use >
AT
FI
IT
PL
GB
RO
BE
FR
LV
PT
IS
TR
CY
DE
LT
SK
LI
HR
CZ
GR
LU
SI
NO
DK
HU
MT
ES
CH
EE
IE
NL
SE
BG
VOICE CODING TECHNOLOGY
The AMBE+2™ voice coding Technology embodied in this
product is protected by intellectual property rights including
patent rights, copyrights and trade secrets of Digital Voice
Systems, Inc. This voice coding Technology is licensed solely
for use within this Communications Equipment. The user of
this Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse engineer, or disassemble
the Object Code, or in any other way convert the Object Code
into a human-readable form. U.S. Patent Nos.
#5,870,405, #5,826,222, #5,754,974, #5,701,390, #5,715,365,
#5,649,050, #5,630,011, #5,581,656, #5,517,511, #5,491,772,
#5,247,579, #5,226,084 and #5,195,166.
MISE EN GARDE:
Tout changement ou modiication, non expressément approuvé par Icom Inc., peut annuler l'autorisation de l'utilisateur à utiliser cet appareil conformément à la réglementation FCC.
USE the specified microphone only. Other microphones
have different pin assignments and may damage the radio.
DO NOT use or place the radio in areas with temperatures
below –30°C (–22°F) or above +60°C (+140°F), or in areas
subject to direct sunlight, such as the dashboard.
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany,
France, Spain, Russia and/or other countries.
AMBE+2 is a trademark and property of Digital Voice Systems Inc.
All other products or brands are registered trademarks or trademarks of their
respective holders.
The GPS receiver may not work if the radio transmits near
the 510 MHz. This is made in the internal circuit and does
not indicate a radio malfunction.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
A-7148?-1EX
Printed in Japan
© 2014 Icom Inc.
SAFETY TRAINING INFORMATION
W ARN ING
Your Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed
for and classified as “Occupational Use Only”,
meaning it must be used only during the course
of employment by individuals aware of the hazards, and the ways to minimize such hazards. This
radio is NOT intended for use by the “General
Population” in an uncontrolled environment.
•฀฀For฀compliance฀with฀FCC฀and฀IC฀RF฀Exposure฀Requirements, the transmitter antenna installation shall
comply with the following two conditions:
1. The transmitter antenna gain shall not exceed 0 dBi.
2. IC-F5360D:
The antenna is required to be located outside of a vehicle and
kept at a distance of 45 centimeters or more between the transmitting antenna of this device and any persons during operation.
For small vehicle as worst case, the antenna shall be located on
the roof top at any place on the centre line along the vehicle in
order to achieve 45 centimeters separation distance. In order to
ensure this distance is met, the installation of the antenna must
be mounted at least 45 centimeters away from the nearest edge
of the vehicle in order to protect against exposure to bystanders.
2. IC-F6360D:
The antenna is required to be located outside of a vehicle and
kept at a distance of 37 centimeters or more between the transmitting antenna of this device and any persons during operation.
For small vehicle as worst case, the antenna shall be located on
the roof top at any place on the centre line along the vehicle in
order to achieve 37 centimeters separation distance. In order to
ensure this distance is met, the installation of the antenna must
be mounted at least 37 centimeters away from the nearest edge
of the vehicle in order to protect against exposure to bystanders.
3. IC-F5360D:
Transmit only when people outside the vehicle are at least the
recommended minimum distance of 100 centimeters away
from the properly installed antenna. This separation distance
will ensure that there is sufficient distance from a properly
installed externally-mounted antenna to satisfy the RF exposure
requirements in the applicable RF exposure compliance
standards.
3. IC-F6360D:
Transmit only when people outside the vehicle are at least
the recommended minimum distance of 82 centimeters away
from the properly installed antenna. This separation distance
will ensure that there is sufficient distance from a properly
installed externally-mounted antenna to satisfy the RF exposure
requirements in the applicable RF exposure compliance
standards.
To ensure that your exposure to RF electromagnetic energy is within the FCC and IC allowable
limits for occupational use, always adhere to the
following guidelines:
C AU TIO N
•฀฀DO NOT operate the radio without a proper antenna attached, as
this may damage the radio and may also cause you to exceed FCC
and IC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or an antenna specifically
authorized by the manufacturer for use with this radio.
•฀฀DO NOT transmit for more than 50% of total radio use time (“50%
duty cycle”). Transmitting more than 50% of the time can cause
FCC and IC RF exposure compliance requirements to be exceeded. The radio is transmitting when the LED indicator lights red.
You can cause the radio to transmit by pressing the “PTT” switch.
Electromagnetic Interference/Compatibility
During transmissions, your Icom radio generates RF energy that can
possibly cause interference with other devices or systems. To avoid
such interference, turn off the radio in areas where signs are posted
to do so. DO NOT operate the transmitter in areas that are sensitive
to electromagnetic radiation such as hospitals, aircraft, and blasting
sites.
SAFETY TRAINING INFORMATION (Continued)
Votre radio Icom produit une énergie électromagnétique de radiofréquences (RF), en mode
de transmission. Cette radio est conçue pour
un «usage professionnel seulement» et clasA V E R T I S S E M E N T sée comme tel, ce qui signiie qu’elle doit être
utilisée uniquement dans le cadre d’un travail
par des personnes conscientes des dangers et
des mesures visant à minimiser ces dangers.
Elle N’EST PAS conçue pour une «utilisation
grand public», dans un environnement non
contrôlé.
• Ain de satisfaire aux exigences de la FCC et d’IC en matière
d’exposition aux RF, il est nécessaire que l’antenne soit installée
conformément aux trois conditions suivantes:
1. Le gain de l’antenne du radio émetteur ne doit pas dépasser
0dBi.
2. IC-F5360D:
Il faut que l’antenne émettrice de cet appareil soit placée à l’extérieur d’un véhicule et tenue éloignée d’au moins 45 cm de toute
personne pendant le fonctionnement. Dans le pire des cas, pour
un petit véhicule, l’antenne doit être placée sur le toit, n’importe
où dans l’axe central du véhicule, ain de respecter une distance
de 45 cm du bord le plus rapproché du véhicule et ainsi éviter
que les personnes présentes soient exposées.
2. IC-F6360D:
Il faut que l’antenne émettrice de cet appareil soit placée à l’extérieur d’un véhicule et tenue éloignée d’au moins 37 cm de toute
personne pendant le fonctionnement. Dans le pire des cas, pour
un petit véhicule, l’antenne doit être placée sur le toit, n’importe
où dans l’axe central du véhicule, ain de respecter une distance
de 37 cm du bord le plus rapproché du véhicule et ainsi éviter
que les personnes présentes soient exposées.
3. IC-F5360D:
Émettre uniquement lorsque les personnes à l’extérieur du véhicule se trouvent à au moins la distance minimale recommandée
de 100 cm de l’antenne correctement installée. Cette distance
de sécurité assurera que les personnes soient placées sufisamment loin d’une antenne correctement ixée à l’extérieur pour satisfaire aux exigences en matière d’exposition aux RF, en vertu
des normes de conformité applicables.
3. IC-F6360D:
Émettre uniquement lorsque les personnes à l’extérieur du véhicule se trouvent à au moins la distance minimale recommandée
de 82 cm de l’antenne correctement installée. Cette distance de
sécurité assurera que les personnes soient placées sufisamment loin d’une antenne correctement ixée à l’extérieur pour satisfaire aux exigences en matière d’exposition aux RF, en vertu
des normes de conformité applicables.
Ain de vous assurer que votre exposition à
une énergie électromagnétique de RF se situe
dans les limites permises par la FCC et d’IC
pour une utilisation grand public, veuillez en
MISE EN GARDE tout temps respecter les directives suivantes:
• NE PAS faire fonctionner la radio sans qu’une antenne appropriée y soit ixée, car ceci risque d’endommager la radio et causer une exposition supérieure aux limites établies par la FCC et
d’IC. L’antenne appropriée est celle qui est fournie avec cette
radio par le fabricant ou une antenne spécialement autorisée
par le fabricant pour être utilisée avec cette radio.
• NE PAS émettre pendant plus de 50 % du temps total d’utilisation de l’appareil («50 % du facteur d’utilisation»). Émettre pendant plus de 50 % du temps total d’utilisation peut causer une
exposition aux RF supérieure aux limites établies par la FCC et
d’IC. Lorsque le voyant DEL rouge s’allume, cette radio est en
train d’émettre. La radio émettra si vous appuyez sur le bouton
du microphone.
Interférence électromagnétique et compatibilité
En mode de transmission, votre radio Icom produit de l’énergie de
RF qui peut provoquer des interférences avec d’autres appareils ou
systèmes. Pour éviter de telles interférences, mettez la radio hors
tension dans les secteurs où une signalisation l’exige. NE PAS faire
fonctionner l’émetteur dans des secteurs sensibles au rayonnement
électromagnétique tels que les hôpitaux, les aéronefs et les sites de
dynamitage.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Create Date                     : 2014:04:15 11:39:49+09:00
Creator                         : Adobe InDesign CS3_J (5.0.4)
Modify Date                     : 2014:05:29 15:46:31-04:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2014:05:29 15:46:31-04:00
Creator Tool                    : Adobe InDesign CS3_J (5.0.4)
Format                          : application/pdf
Document ID                     : uuid:ad8f60f3-c34b-459d-aeda-0ab3f539c3eb
Instance ID                     : uuid:88494e6f-e9ea-468f-b63f-4e46316e7ea5
Producer                        : Adobe PDF Library 8.0
Page Count                      : 2
EXIF Metadata provided by EXIF.tools
FCC ID Filing: AFJ366501

Navigation menu